PIC18F2450/4450 Data Sheet 24/40/44-Pin High-Performance, 12 MIPS, Enhanced Flash, USB Microcontrollers with nanoWatt Technology © 2008 Microchip Technology Inc. DS39760D Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PRO MATE, rfPIC and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM, PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2008, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS39760D-page ii © 2008 Microchip Technology Inc. PIC18F2450/4450 28/40/44-Pin High-Performance, 12 MIPS, Enhanced Flash, USB Microcontrollers with nanoWatt Technology Universal Serial Bus Features: Peripheral Highlights: • USB V2.0 Compliant • Low Speed (1.5 Mb/s) and Full Speed (12 Mb/s) • Supports Control, Interrupt, Isochronous and Bulk Transfers • Supports Up to 32 Endpoints (16 bidirectional) • 256-Byte Dual Access RAM for USB • On-Chip USB Transceiver with On-Chip Voltage Regulator • Interface for Off-Chip USB Transceiver • • • • High-Current Sink/Source: 25 mA/25 mA Three External Interrupts Three Timer modules (Timer0 to Timer2) Capture/Compare/PWM (CCP) module: - Capture is 16-bit, max. resolution 5.2 ns - Compare is 16-bit, max. resolution 83.3 ns - PWM output: PWM resolution is 1 to 10-bit • Enhanced USART module: - LIN bus support • 10-Bit, Up to 13-Channel Analog-to-Digital Converter module (A/D): - Up to 100 ksps sampling rate - Programmable acquisition time Power-Managed Modes: • • • • • • • • Run: CPU on, Peripherals on Idle: CPU off, Peripherals on Sleep: CPU off, Peripherals off Idle mode Currents Down to 5.8 μA Typical Sleep mode Currents Down to 0.1 μA Typical Timer1 Oscillator: 1.8 μA Typical, 32 kHz, 2V Watchdog Timer: 2.1 μA Typical Two-Speed Oscillator Start-up Special Microcontroller Features: Flexible Oscillator Structure: • Four Crystal modes, including High-Precision PLL for USB • Two External Clock modes, up to 48 MHz • Internal 31 kHz Oscillator • Secondary Oscillator using Timer1 @ 32 kHz • Dual Oscillator Options allow Microcontroller and USB module to Run at Different Clock Speeds • Fail-Safe Clock Monitor: - Allows for safe shutdown if any clock stops Program Memory • C Compiler Optimized Architecture with Optional Extended Instruction Set • Flash Memory Retention: > 40 Years • Self-Programmable under Software Control • Priority Levels for Interrupts • 8 x 8 Single-Cycle Hardware Multiplier • Extended Watchdog Timer (WDT): - Programmable period from 4 ms to 131s • Programmable Code Protection • Single-Supply In-Circuit Serial Programming™ (ICSP™) via Two Pins • In-Circuit Debug (ICD) via Two Pins • Optional Dedicated ICD/ICSP Port (44-pin TQFP devices only) • Wide Operating Voltage Range (2.0V to 5.5V) Device Flash (bytes) # Single-Word Instructions Data Memory SRAM (bytes) PIC18F2450 16K 8192 768* 23 10 1 1 1/2 PIC18F4450 16K 8192 768* 34 13 1 1 1/2 * I/O 10-Bit A/D (ch) CCP EUSART Timers 8/16-Bit Includes 256 bytes of dual access RAM used by USB module and shared with data memory. © 2008 Microchip Technology Inc. DS39760D-page 1 PIC18F2450/4450 Pin Diagrams 1 2 3 4 5 6 7 8 9 10 11 12 13 14 MCLR/VPP/RE3 RA0/AN0 RA1/AN1 RA2/AN2/VREFRA3/AN3/VREF+ RA4/T0CKI/RCV RA5/AN4/HLVDIN VSS OSC1/CLKI OSC2/CLKO/RA6 RC0/T1OSO/T1CKI RC1/T1OSI/UOE RC2/CCP1 VUSB PIC18F2450 28-Pin SPDIP, SOIC 28 27 26 25 24 23 22 21 20 19 18 17 16 15 RB7/KBI3/PGD RB6/KBI2/PGC RB5/KBI1/PGM RB4/AN11/KBI0 RB3/AN9/VPO RB2/AN8/INT2/VMO RB1/AN10/INT1 RB0/AN12/INT0 VDD VSS RC7/RX/DT RC6/TX/CK RC5/D+/VP RC4/D-/VM RA1/AN1 RA0/AN0 MCLR/VPP/RE3 RB7/KBI3/PGD RB6/KBI2/PGC RB5/KBI1/PGM RB4/AN11/KBI0 28-Pin QFN 28 27 26 25 24 23 22 1 2 3 4 5 6 7 PIC18F2450 8 9 10 11 12 13 14 21 20 19 18 17 16 15 RB3/AN9/VPO RB2/AN8/INT2/VMO RB1/AN10/INT1 RB0/AN12/INT0 VDD VSS RC7/RX/DT RC0/T1OSO/T1CKI RC1/T1OSI/UOE RC2/CCP1 VUSB RC4/D-/VM RC5/D+/VP RC6/TX/CK RA2/AN2/VREFRA3/AN3/VREF+ RA4/T0CKI/RCV RA5/AN4/HLVDIN VSS OSC1/CLKI OSC2/CLKO/RA6 DS39760D-page 2 © 2008 Microchip Technology Inc. PIC18F2450/4450 Pin Diagrams (Continued) MCLR/VPP/RE3 RA0/AN0 RA1/AN1 RA2/AN2/VREFRA3/AN3/VREF+ RA4/T0CKI/RCV RA5/AN4/HLVDIN RE0/AN5 RE1/AN6 RE2/AN7 VDD VSS OSC1/CLKI OSC2/CLKO/RA6 RC0/T1OSO/T1CKI RC1/T1OSI/UOE RC2/CCP1 VUSB RD0 RD1 RB7/KBI3/PGD RB6/KBI2/PGC RB5/KBI1/PGM RB4/AN11/KBI0 RB3/AN9/VPO RB2/AN8/INT2/VMO RB1/AN10/INT1 RB0/AN12/INT0 VDD VSS RD7 RD6 RD5 RD4 RC7/RX/DT RC6/TX/CK RC5/D+/VP RC4/D-/VM RD3 RD2 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 PIC18F4450 33 32 31 30 29 28 27 26 25 24 23 12 13 14 15 16 17 18 19 20 21 22 1 2 3 4 5 6 7 8 9 10 11 OSC2/CLKO/RA6 OSC1/CLKI VSS AVSS VDD AVDD RE2/AN7 RE1/AN6 RE0/AN5 RA5/AN4/HLVDIN RA4/T0CKI/RCV RB3/AN9/VPO NC RB4/AN11/KBI0 RB5/KBI1/PGM RB6/KBI2/PGC RB7/KBI3/PGD MCLR/VPP/RE3 RA0/AN0 RA1/AN1 RA2/AN2/VREFRA3/AN3/VREF+ RC7/RX/DT RD4 RD5 RD6 RD7 VSS AVDD VDD RB0/AN12/INT0 RB1/AN10/INT1 RB2/AN8/INT2/VMO 44 43 42 41 40 39 38 37 36 35 34 RC6/TX/CK RC5/D+/VP RC4/D-/VM RD3 RD2 RD1 RD0 VUSB RC2/CCP1 RC1/T1OSI/UOE RC0/T1OSO/T1CKI 44-Pin QFN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PIC18F4450 40-Pin PDIP © 2008 Microchip Technology Inc. DS39760D-page 3 PIC18F2450/4450 Pin Diagrams (Continued) PIC18F4450 33 32 31 30 29 28 27 26 25 24 23 12 13 14 15 16 17 18 19 20 21 22 1 2 3 4 5 6 7 8 9 10 11 NC/ICRST(1)/ICVPP(1) RC0/T1OSO/T1CKI OSC2/CLKO/RA6 OSC1/CLKI VSS VDD RE2/AN7 RE1/AN6 RE0/AN5 RA5/AN4/HLVDIN RA4/T0CKI/RCV NC/ICCK(1)/ICPGC(1) NC/ICDT(1)/ICPGD(1) RB4/AN11/KBI0 RB5/KBI1/PGM RB6/KBI2/PGC RB7/KBI3/PGD MCLR/VPP/RE3 RA0/AN0 RA1/AN1 RA2/AN2/VREFRA3/AN3/VREF+ RC7/RX/DT RD4 RD5 RD6 RD7 VSS VDD RB0/AN12/INT0 RB1/AN10/INT1 RB2/AN8/INT2/VMO RB3/AN9/VPO 44 43 42 41 40 39 38 37 36 35 34 RC6/TX/CK RC5/D+/VP RC4/D-/VM RD3 RD2 RD1 RD0 VUSB RC2/CCP1 RC1/T1OSI/UOE NC/ICPORTS(1) 44-Pin TQFP Note 1: DS39760D-page 4 Special ICPORT features are available in select circumstances. For more information, see Section 18.9 “Special ICPORT Features (Designated Packages Only)”. © 2008 Microchip Technology Inc. PIC18F2450/4450 Table of Contents 1.0 Device Overview .......................................................................................................................................................................... 7 2.0 Oscillator Configurations ............................................................................................................................................................ 23 3.0 Power-Managed Modes ............................................................................................................................................................. 33 4.0 Reset .......................................................................................................................................................................................... 41 5.0 Memory Organization ................................................................................................................................................................. 53 6.0 Flash Program Memory.............................................................................................................................................................. 73 7.0 8 x 8 Hardware Multiplier............................................................................................................................................................ 83 8.0 Interrupts .................................................................................................................................................................................... 85 9.0 I/O Ports ..................................................................................................................................................................................... 99 10.0 Timer0 Module ......................................................................................................................................................................... 111 11.0 Timer1 Module ......................................................................................................................................................................... 115 12.0 Timer2 Module ......................................................................................................................................................................... 121 13.0 Capture/Compare/PWM (CCP) Module ................................................................................................................................... 123 14.0 Universal Serial Bus (USB) ...................................................................................................................................................... 129 15.0 Enhanced Universal Synchronous Receiver Transmitter (EUSART)....................................................................................... 153 16.0 10-Bit Analog-to-Digital Converter (A/D) Module ..................................................................................................................... 175 17.0 High/Low-Voltage Detect (HLVD)............................................................................................................................................. 185 18.0 Special Features of the CPU.................................................................................................................................................... 191 19.0 Instruction Set Summary .......................................................................................................................................................... 213 20.0 Development Support............................................................................................................................................................... 263 21.0 Electrical Characteristics .......................................................................................................................................................... 267 22.0 Packaging Information.............................................................................................................................................................. 295 Appendix A: Revision History............................................................................................................................................................. 307 Appendix B: Device Differences ........................................................................................................................................................ 308 Appendix C: Conversion Considerations ........................................................................................................................................... 309 Appendix D: Migration From Baseline to Enhanced Devices ............................................................................................................ 309 Appendix E: Migration From Mid-Range to Enhanced Devices ......................................................................................................... 310 Appendix F: Migration From High-End to Enhanced Devices............................................................................................................ 310 Index ................................................................................................................................................................................................. 311 The Microchip Web Site ..................................................................................................................................................................... 319 Customer Change Notification Service .............................................................................................................................................. 319 Customer Support .............................................................................................................................................................................. 319 Reader Response .............................................................................................................................................................................. 320 Product Identification System ............................................................................................................................................................ 321 © 2008 Microchip Technology Inc. DS39760D-page 5 PIC18F2450/4450 TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at [email protected] or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Web site; http://www.microchip.com • Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products. DS39760D-page 6 © 2008 Microchip Technology Inc. PIC18F2450/4450 1.0 DEVICE OVERVIEW This document contains device-specific information for the following devices: • PIC18F2450 • PIC18F4450 This family of devices offers the advantages of all PIC18 microcontrollers – namely, high computational performance at an economical price – with the addition of high-endurance, Enhanced Flash program memory. In addition to these features, the PIC18F2450/4450 family introduces design enhancements that make these microcontrollers a logical choice for many high-performance, power sensitive applications. 1.1 1.1.1 New Core Features nanoWatt TECHNOLOGY All of the devices in the PIC18F2450/4450 family incorporate a range of features that can significantly reduce power consumption during operation. Key items include: • Alternate Run Modes: By clocking the controller from the Timer1 source or the internal RC oscillator, power consumption during code execution can be reduced by as much as 90%. • Multiple Idle Modes: The controller can also run with its CPU core disabled but the peripherals still active. In these states, power consumption can be reduced even further, to as little as 4% of normal operation requirements. • On-the-Fly Mode Switching: The powermanaged modes are invoked by user code during operation, allowing the user to incorporate power-saving ideas into their application’s software design. • Low Consumption in Key Modules: The power requirements for both Timer1 and the Watchdog Timer are minimized. See Section 21.0 “Electrical Characteristics” for values. 1.1.2 1.1.3 MULTIPLE OSCILLATOR OPTIONS AND FEATURES All of the devices in the PIC18F2450/4450 family offer twelve different oscillator options, allowing users a wide range of choices in developing application hardware. These include: • Four Crystal modes using crystals or ceramic resonators. • Four External Clock modes, offering the option of using two pins (oscillator input and a divide-by-4 clock output) or one pin (oscillator input, with the second pin reassigned as general I/O). • An INTRC source (approximately 31 kHz, stable over temperature and VDD). This option frees an oscillator pin for use as an additional general purpose I/O. • A Phase Lock Loop (PLL) frequency multiplier, available to both the High-Speed Crystal and External Oscillator modes, which allows a wide range of clock speeds from 4 MHz to 48 MHz. • Asynchronous dual clock operation, allowing the USB module to run from a high-frequency oscillator while the rest of the microcontroller is clocked from an internal low-power oscillator. The internal oscillator provides a stable reference source that gives the family additional features for robust operation: • Fail-Safe Clock Monitor: This option constantly monitors the main clock source against a reference signal provided by the internal oscillator. If a clock failure occurs, the controller is switched to the internal oscillator, allowing for continued low-speed operation or a safe application shutdown. • Two-Speed Start-up: This option allows the internal oscillator to serve as the clock source from Power-on Reset, or wake-up from Sleep mode, until the primary clock source is available. UNIVERSAL SERIAL BUS (USB) Devices in the PIC18F2450/4450 family incorporate a fully featured Universal Serial Bus communications module that is compliant with the USB Specification Revision 2.0. The module supports both low-speed and full-speed communication for all supported data transfer types. It also incorporates its own on-chip transceiver and 3.3V regulator and supports the use of external transceivers and voltage regulators. © 2008 Microchip Technology Inc. DS39760D-page 7 PIC18F2450/4450 1.2 Other Special Features • Memory Endurance: The Enhanced Flash cells for program memory are rated to last for many thousands of erase/write cycles – up to 100,000. • Self-Programmability: These devices can write to their own program memory spaces under internal software control. By using a bootloader routine, located in the protected Boot Block at the top of program memory, it becomes possible to create an application that can update itself in the field. • Extended Instruction Set: The PIC18F2450/ 4450 family introduces an optional extension to the PIC18 instruction set, which adds 8 new instructions and an Indexed Literal Offset Addressing mode. This extension, enabled as a device configuration option, has been specifically designed to optimize re-entrant application code originally developed in high-level languages such as C. • Enhanced Addressable USART: This serial communication module is capable of standard RS-232 operation and provides support for the LIN bus protocol. Other enhancements include Automatic Baud Rate Detection and a 16-bit Baud Rate Generator for improved resolution. • 10-Bit A/D Converter: This module incorporates programmable acquisition time, allowing for a channel to be selected and a conversion to be initiated, without waiting for a sampling period and thus, reducing code overhead. • Dedicated ICD/ICSP Port: These devices introduce the use of debugger and programming pins that are not multiplexed with other microcontroller features. Offered as an option in select packages, this feature allows users to develop I/O intensive applications while retaining the ability to program and debug in the circuit. DS39760D-page 8 1.3 Details on Individual Family Members Devices in the PIC18F2450/4450 family are available in 28-pin and 40/44-pin packages. Block diagrams for the two groups are shown in Figure 1-1 and Figure 1-2. The devices are differentiated from each other in the following two ways: 1. 2. A/D channels (10 for 28-pin devices, 13 for 40/44-pin devices). I/O ports (3 bidirectional ports and 1 input only port on 28-pin devices, 5 bidirectional ports on 40/44-pin devices). All other features for devices in this family are identical. These are summarized in Table 1-1. The pinouts for all devices are listed in Table 1-2 and Table 1-3. Like all Microchip PIC18 devices, members of the PIC18F2450/4450 family are available as both standard and low-voltage devices. Standard devices with Enhanced Flash memory, designated with an “F” in the part number (such as PIC18F2450), accommodate an operating VDD range of 4.2V to 5.5V. Low-voltage parts, designated by “LF” (such as PIC18LF2450), function over an extended VDD range of 2.0V to 5.5V. © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 1-1: DEVICE FEATURES Features PIC18F2450 PIC18F4450 DC – 48 MHz DC – 48 MHz Program Memory (Bytes) 16384 16384 Program Memory (Instructions) 8192 8192 Data Memory (Bytes) 768 768 Operating Frequency Interrupt Sources 13 13 Ports A, B, C, (E) Ports A, B, C, D, E Timers 3 3 Capture/Compare/PWM Modules 1 1 I/O Ports Enhanced USART 1 1 Universal Serial Bus (USB) Module 1 1 10 Input Channels 13 Input Channels POR, BOR, RESET Instruction, Stack Full, Stack Underflow (PWRT, OST), MCLR (optional), WDT POR, BOR, RESET Instruction, Stack Full, Stack Underflow (PWRT, OST), MCLR (optional), WDT Yes Yes 10-Bit Analog-to-Digital Module Resets (and Delays) Programmable Low-Voltage Detect Programmable Brown-out Reset Instruction Set Packages © 2008 Microchip Technology Inc. Yes Yes 75 Instructions; 83 with Extended Instruction Set enabled 75 Instructions; 83 with Extended Instruction Set enabled 28-Pin SPDIP 28-Pin SOIC 28-Pin QFN 40-Pin PDIP 44-Pin QFN 44-Pin TQFP DS39760D-page 9 PIC18F2450/4450 FIGURE 1-1: PIC18F2450 (28-PIN) BLOCK DIAGRAM Data Bus<8> Table Pointer<21> 8 inc/dec logic PORTA Data Memory (2 Kbytes) PCLATU PCLATH 21 20 Address Latch PCU PCH PCL Program Counter 12 Data Address<12> 31 Level Stack 4 BSR Address Latch Program Memory (24/32 Kbytes) STKPTR Data Latch 8 Instruction Bus <16> RA0/AN0 RA1/AN1 RA2/AN2/VREFRA3/AN3/VREF+ RA4/T0CKI/RCV RA5/AN4/HLVDIN OSC2/CLKO/RA6 Data Latch 8 4 Access Bank 12 FSR0 FSR1 FSR2 12 PORTB RB0/AN12/INT0 RB1/AN10/INT1 RB2/AN8/INT2/VMO RB3/AN9/VPO RB4/AN11/KBI0 RB5/KBI1/PGM RB6/KBI2/PGC RB7/KBI3/PGD inc/dec logic Table Latch Address Decode ROM Latch IR 8 Instruction Decode & Control State Machine Control Signals PRODH PRODL 3 (2) OSC1 OSC2(2) Internal Oscillator Block Power-up Timer Oscillator Start-up Timer Power-on Reset INTRC Oscillator T1OSI MCLR(1) VDD, VSS BOR HLVD Timer0 Note 1: 2: 8 ALU<8> 8 Timer1 CCP1 8 8 PORTE Band Gap Reference USB Voltage Regulator VUSB W 8 Brown-out Reset Fail-Safe Clock Monitor Single-Supply Programming In-Circuit Debugger RC0/T1OSO/T1CKI RC1/T1OSI/UOE RC2/CCP1 RC4/D-/VM RC5/D+/VP RC6/TX/CK RC7/RX/DT 8 BITOP 8 Watchdog Timer T1OSO PORTC 8 x 8 Multiply Timer2 EUSART MCLR/VPP/RE3(1) ADC 10-Bit USB RE3 is multiplexed with MCLR and is only available when the MCLR Resets are disabled. OSC1/CLKI and OSC2/CLKO are only available in select oscillator modes and when these pins are not being used as digital I/O. Refer to Section 2.0 “Oscillator Configurations” for additional information. DS39760D-page 10 © 2008 Microchip Technology Inc. PIC18F2450/4450 FIGURE 1-2: PIC18F4450 (40/44-PIN) BLOCK DIAGRAM Data Bus<8> Table Pointer<21> Data Memory (2 Kbytes) PCLATU PCLATH 21 20 Address Latch PCU PCH PCL Program Counter 12 Data Address<12> 31 Level Stack 4 BSR Address Latch Program Memory (24/32 Kbytes) STKPTR Data Latch 8 Instruction Bus <16> RA0/AN0 RA1/AN1 RA2/AN2/VREFRA3/AN3/VREF+ RA4/T0CKI/RCV RA5/AN4/HLVDIN OSC2/CLKO/RA6 Data Latch 8 8 inc/dec logic PORTA 12 FSR0 FSR1 FSR2 PORTB RB0/AN12/INT0 RB1/AN10/INT1 RB2/AN8/INT2/VMO RB3/AN9/VPO RB4/AN11/KBI0 RB5/KBI1/PGM RB6/KBI2/PGC RB7/KBI3/PGD 4 Access Bank 12 inc/dec logic Table Latch PORTC Address Decode ROM Latch RC0/T1OSO/T1CKI RC1/T1OSI/UOE RC2/CCP1 RC4/D-/VM RC5/D+/VP RC6/TX/CK RC7/RX/DT IR 8 Instruction Decode & Control State Machine Control Signals PRODH PRODL 3 VDD, VSS OSC1(2) OSC2(2) T1OSI Internal Oscillator Block Power-up Timer INTRC Oscillator Oscillator Start-up Timer T1OSO Power-on Reset ICPGC(3) Watchdog Timer Single-Supply Programming ICPGD(3) In-Circuit Debugger (3) ICPORTS ICRST(3) MCLR(1) PORTD 8 x 8 Multiply RD0 RD1 RD2 RD3 RD4 RD5 RD6 RD7 8 BITOP 8 W 8 8 8 8 ALU<8> 8 Brown-out Reset Fail-Safe Clock Monitor PORTE Band Gap Reference RE0/AN5 RE1/AN6 RE2/AN7 MCLR/VPP/RE3(1) USB Voltage Regulator VUSB BOR HLVD Timer0 CCP1 Note 1: 2: 3: Timer1 EUSART Timer2 ADC 10-Bit USB RE3 is multiplexed with MCLR and is only available when the MCLR Resets are disabled. OSC1/CLKI and OSC2/CLKO are only available in select oscillator modes and when these pins are not being used as digital I/O. Refer to Section 2.0 “Oscillator Configurations” for additional information. These pins are only available on 44-pin TQFP under certain conditions. Refer to Section 18.9 “Special ICPORT Features (Designated Packages Only)” for additional information. © 2008 Microchip Technology Inc. DS39760D-page 11 PIC18F2450/4450 TABLE 1-2: PIC18F2450 PINOUT I/O DESCRIPTIONS Pin Number Pin Name MCLR/VPP/RE3 MCLR Pin Buffer SPDIP, QFN Type Type SOIC 1 26 I ST P I ST I I Analog Analog O — CLKO O — RA6 I/O TTL VPP RE3 OSC1/CLKI OSC1 CLKI 9 OSC2/CLKO/RA6 OSC2 10 6 7 Description Master Clear (input) or programming voltage (input). Master Clear (Reset) input. This pin is an active-low Reset to the device. Programming voltage input. Digital input. Oscillator crystal or external clock input. Oscillator crystal input or external clock source input. External clock source input. Always associated with pin function OSC1. (See OSC2/CLKO pin.) Oscillator crystal or clock output. Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. In select modes, OSC2 pin outputs CLKO which has 1/4 the frequency of OSC1 and denotes the instruction cycle rate. General purpose I/O pin. Legend: TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels O = Output DS39760D-page 12 CMOS = CMOS compatible input or output I = Input P = Power © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 1-2: PIC18F2450 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number Pin Buffer SPDIP, QFN Type Type SOIC Description PORTA is a bidirectional I/O port. RA0/AN0 RA0 AN0 2 RA1/AN1 RA1 AN1 3 RA2/AN2/VREFRA2 AN2 VREF- 4 RA3/AN3/VREF+ RA3 AN3 VREF+ 5 RA4/T0CKI/RCV RA4 T0CKI RCV 6 RA5/AN4/HLVDIN RA5 AN4 HLVDIN 7 RA6 — 27 I/O I TTL Analog Digital I/O. Analog input 0. I/O I TTL Analog Digital I/O. Analog input 1. I/O I I TTL Analog Analog Digital I/O. Analog input 2. A/D reference voltage (low) input. I/O I I TTL Analog Analog Digital I/O. Analog input 3. A/D reference voltage (high) input. I/O I I ST ST TTL I/O I I TTL Analog Analog Digital I/O. Analog input 4. High/Low-Voltage Detect input. — — See the OSC2/CLKO/RA6 pin. 28 1 2 3 4 — Legend: TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels O = Output © 2008 Microchip Technology Inc. Digital I/O. Timer0 external clock input. External USB transceiver RCV input. CMOS = CMOS compatible input or output I = Input P = Power DS39760D-page 13 PIC18F2450/4450 TABLE 1-2: PIC18F2450 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number Pin Buffer SPDIP, QFN Type Type SOIC Description PORTB is a bidirectional I/O port. PORTB can be software programmed for internal weak pull-ups on all inputs. RB0/AN12/INT0 RB0 AN12 INT0 21 RB1/AN10/INT1 RB1 AN10 INT1 22 RB2/AN8/INT2/VMO RB2 AN8 INT2 VMO 23 RB3/AN9/VPO RB3 AN9 VPO 24 RB4/AN11/KBI0 RB4 AN11 KBI0 25 RB5/KBI1/PGM RB5 KBI1 PGM 26 RB6/KBI2/PGC RB6 KBI2 PGC 27 RB7/KBI3/PGD RB7 KBI3 PGD 28 18 I/O I I TTL Analog ST Digital I/O. Analog input 12. External interrupt 0. I/O I I TTL Analog ST Digital I/O. Analog input 10. External interrupt 1. I/O I I O TTL Analog ST — Digital I/O. Analog input 8. External interrupt 2. External USB transceiver VMO output. I/O I O TTL Analog — Digital I/O. Analog input 9. External USB transceiver VPO output. I/O I I TTL Analog TTL Digital I/O. Analog input 11. Interrupt-on-change pin. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. Low-Voltage ICSP™ Programming enable pin. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. In-Circuit Debugger and ICSP programming clock pin. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. In-Circuit Debugger and ICSP programming data pin. 19 20 21 22 23 24 25 Legend: TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels O = Output DS39760D-page 14 CMOS = CMOS compatible input or output I = Input P = Power © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 1-2: PIC18F2450 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number Pin Buffer SPDIP, QFN Type Type SOIC Description PORTC is a bidirectional I/O port. RC0/T1OSO/T1CKI RC0 T1OSO T1CKI 11 RC1/T1OSI/UOE RC1 T1OSI UOE 12 RC2/CCP1 RC2 CCP1 13 RC4/D-/VM RC4 DVM 15 RC5/D+/VP RC5 D+ VP 16 RC6/TX/CK RC6 TX CK 17 RC7/RX/DT RC7 RX DT 18 RE3 — VUSB 8 I/O O I ST — ST I/O I O ST CMOS — I/O I/O ST ST Digital I/O. Capture 1 input/Compare 1 output/PWM1 output. I I/O I TTL — TTL Digital input. USB differential minus line (input/output). External USB transceiver VM input. I I/O O TTL — TTL Digital input. USB differential plus line (input/output). External USB transceiver VP input. I/O O I/O ST — ST Digital I/O. EUSART asynchronous transmit. EUSART synchronous clock (see RX/DT). I/O I I/O ST ST ST Digital I/O. EUSART asynchronous receive. EUSART synchronous data (see TX/CK). — — — See MCLR/VPP/RE3 pin. 14 11 P — Internal USB 3.3V voltage regulator. Output, positive supply for internal USB transceiver. VSS 8, 19 5, 16 P — Ground reference for logic and I/O pins. VDD 20 17 P — Positive supply for logic and I/O pins. Digital I/O. Timer1 oscillator output. Timer1external clock input. 9 Digital I/O. Timer1 oscillator input. External USB transceiver OE output. 10 12 13 14 15 Legend: TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels O = Output © 2008 Microchip Technology Inc. CMOS = CMOS compatible input or output I = Input P = Power DS39760D-page 15 PIC18F2450/4450 TABLE 1-3: PIC18F4450 PINOUT I/O DESCRIPTIONS Pin Name MCLR/VPP/RE3 MCLR Pin Number PDIP QFN 1 18 Pin Buffer TQFP Type Type 18 I ST P I — ST I I Analog Analog O — CLKO O — RA6 I/O TTL VPP RE3 OSC1/CLKI OSC1 CLKI 13 OSC2/CLKO/RA6 OSC2 14 32 33 30 31 Description Master Clear (input) or programming voltage (input). Master Clear (Reset) input. This pin is an active-low Reset to the device. Programming voltage input. Digital input. Oscillator crystal or external clock input. Oscillator crystal input or external clock source input. External clock source input. Always associated with pin function OSC1. (See OSC2/CLKO pin.) Oscillator crystal or clock output. Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. In select modes, OSC2 pin outputs CLKO which has 1/4 the frequency of OSC1 and denotes the instruction cycle rate. General purpose I/O pin. Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: These pins are No Connect unless the ICPRT Configuration bit is set. For NC/ICPORTS, the pin is No Connect unless ICPRT is set and the DEBUG Configuration bit is cleared. DS39760D-page 16 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 1-3: PIC18F4450 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number PDIP QFN RA0/AN0 RA0 AN0 2 19 RA1/AN1 RA1 AN1 3 RA2/AN2/VREFRA2 AN2 VREF- 4 RA3/AN3/VREF+ RA3 AN3 VREF+ 5 RA4/T0CKI/RCV RA4 T0CKI RCV 6 RA5/AN4/HLVDIN RA5 AN4 HLVDIN 7 RA6 — Pin Buffer TQFP Type Type Description PORTA is a bidirectional I/O port. 20 21 22 23 24 — 19 I/O I TTL Analog Digital I/O. Analog input 0. I/O I TTL Analog Digital I/O. Analog input 1. I/O I I TTL Analog Analog Digital I/O. Analog input 2. A/D reference voltage (low) input. I/O I I TTL Analog Analog Digital I/O. Analog input 3. A/D reference voltage (high) input. I/O I I ST ST TTL I/O I I TTL Analog Analog Digital I/O. Analog input 4. High/Low-Voltage Detect input. — — See the OSC2/CLKO/RA6 pin. 20 21 22 23 Digital I/O. Timer0 external clock input. External USB transceiver RCV input. 24 — Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: These pins are No Connect unless the ICPRT Configuration bit is set. For NC/ICPORTS, the pin is No Connect unless ICPRT is set and the DEBUG Configuration bit is cleared. © 2008 Microchip Technology Inc. DS39760D-page 17 PIC18F2450/4450 TABLE 1-3: PIC18F4450 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number PDIP QFN Pin Buffer TQFP Type Type Description PORTB is a bidirectional I/O port. PORTB can be software programmed for internal weak pull-ups on all inputs. RB0/AN12/INT0 RB0 AN12 INT0 33 RB1/AN10/INT1 RB1 AN10 INT1 34 RB2/AN8/INT2/VMO RB2 AN8 INT2 VMO 35 RB3/AN9/VPO RB3 AN9 VPO 36 RB4/AN11/KBI0 RB4 AN11 KBI0 37 RB5/KBI1/PGM RB5 KBI1 PGM 38 RB6/KBI2/PGC RB6 KBI2 PGC 39 RB7/KBI3/PGD RB7 KBI3 PGD 40 9 10 11 12 14 15 16 17 8 I/O I I TTL Analog ST Digital I/O. Analog input 12. External interrupt 0. I/O I I TTL Analog ST Digital I/O. Analog input 10. External interrupt 1. I/O I I O TTL Analog ST — Digital I/O. Analog input 8. External interrupt 2. External USB transceiver VMO output. I/O I O TTL Analog — Digital I/O. Analog input 9. External USB transceiver VPO output. I/O I I TTL Analog TTL Digital I/O. Analog input 11. Interrupt-on-change pin. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. Low-Voltage ICSP™ Programming enable pin. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. In-Circuit Debugger and ICSP programming clock pin. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. In-Circuit Debugger and ICSP programming data pin. 9 10 11 14 15 16 17 Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: These pins are No Connect unless the ICPRT Configuration bit is set. For NC/ICPORTS, the pin is No Connect unless ICPRT is set and the DEBUG Configuration bit is cleared. DS39760D-page 18 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 1-3: PIC18F4450 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number PDIP QFN RC0/T1OSO/T1CKI RC0 T1OSO T1CKI 15 34 RC1/T1OSI/UOE RC1 T1OSI UOE 16 RC2/CCP1 RC2 CCP1 17 RC4/D-/VM RC4 DVM 23 RC5/D+/VP RC5 D+ VP 24 RC6/TX/CK RC6 TX CK 25 RC7/RX/DT RC7 RX DT 26 Pin Buffer TQFP Type Type Description PORTC is a bidirectional I/O port. 35 36 42 43 44 1 32 I/O O I ST — ST Digital I/O. Timer1 oscillator output. Timer1 external clock input. I/O I O ST CMOS — I/O I/O ST ST Digital I/O. Capture 1 input/Compare 1 output/PWM1 output. I I/O I TTL — TTL Digital input. USB differential minus line (input/output). External USB transceiver VM input. I I/O I TTL — TTL Digital input. USB differential plus line (input/output). External USB transceiver VP input. I/O O I/O ST — ST Digital I/O. EUSART asynchronous transmit. EUSART synchronous clock (see RX/DT). I/O I I/O ST ST ST Digital I/O. EUSART asynchronous receive. EUSART synchronous data (see TX/CK). 35 Digital I/O. Timer1 oscillator input. External USB transceiver OE output. 36 42 43 44 1 Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: These pins are No Connect unless the ICPRT Configuration bit is set. For NC/ICPORTS, the pin is No Connect unless ICPRT is set and the DEBUG Configuration bit is cleared. © 2008 Microchip Technology Inc. DS39760D-page 19 PIC18F2450/4450 TABLE 1-3: Pin Name PIC18F4450 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Number PDIP QFN Pin Buffer TQFP Type Type Description PORTD is a bidirectional I/O port. RD0 19 38 38 I/O ST Digital I/O. RD1 20 39 39 I/O ST Digital I/O. RD2 21 40 40 I/O ST Digital I/O. RD3 22 41 41 I/O ST Digital I/O. RD4 27 2 2 I/O ST Digital I/O. RD5 28 3 3 I/O ST Digital I/O. RD6 29 4 4 I/O ST Digital I/O. RD7 30 5 5 I/O ST Digital I/O. Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: These pins are No Connect unless the ICPRT Configuration bit is set. For NC/ICPORTS, the pin is No Connect unless ICPRT is set and the DEBUG Configuration bit is cleared. DS39760D-page 20 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 1-3: PIC18F4450 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number PDIP QFN RE0/AN5 RE0 AN5 8 25 RE1/AN6 RE1 AN6 9 RE2/AN7 RE2 AN7 10 RE3 — Pin Buffer TQFP Type Type Description PORTE is a bidirectional I/O port. 26 27 — 25 I/O I ST Analog Digital I/O. Analog input 5. I/O I ST Analog Digital I/O. Analog input 6. I/O I ST Analog Digital I/O. Analog input 7. — — — See MCLR/VPP/RE3 pin. 26 27 VSS 12, 31 6, 30, 31 6, 29 P — Ground reference for logic and I/O pins. VDD 11, 32 7, 8, 7, 28 28, 29 P — Positive supply for logic and I/O pins. P — Internal USB 3.3V voltage regulator output. Positive supply for internal USB transceiver. I/O I/O ST ST No Connect or dedicated ICD/ICSP™ port clock. In-Circuit Debugger clock. ICSP programming clock. I/O I/O ST ST No Connect or dedicated ICD/ICSP port clock. In-Circuit Debugger data. ICSP programming data. I P — — No Connect or dedicated ICD/ICSP port Reset. Master Clear (Reset) input. Programming voltage input. VUSB 18 37 37 NC/ICCK/ICPGC(1) ICCK ICPGC — — 12 NC/ICDT/ICPGD(1) ICDT ICPGD — NC/ICRST/ICVPP(1) ICRST ICVPP — NC/ICPORTS(1) ICPORTS — — 34 P — No Connect or 28-pin device emulation. Enable 28-pin device emulation when connected to VSS. NC — 13 — — — No Connect. — — 13 33 Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: These pins are No Connect unless the ICPRT Configuration bit is set. For NC/ICPORTS, the pin is No Connect unless ICPRT is set and the DEBUG Configuration bit is cleared. © 2008 Microchip Technology Inc. DS39760D-page 21 PIC18F2450/4450 NOTES: DS39760D-page 22 © 2008 Microchip Technology Inc. PIC18F2450/4450 2.0 2.1 OSCILLATOR CONFIGURATIONS Overview Devices in the PIC18F2450/4450 family incorporate a different oscillator and microcontroller clock system than the non-USB PIC18F devices. The addition of the USB module, with its unique requirements for a stable clock source, make it necessary to provide a separate clock source that is compliant with both USB low-speed and full-speed specifications. To accommodate these requirements, PIC18F2450/ 4450 devices include a new clock branch to provide a 48 MHz clock for full-speed USB operation. Since it is driven from the primary clock source, an additional system of prescalers and postscalers has been added to accommodate a wide range of oscillator frequencies. An overview of the oscillator structure is shown in Figure 2-1. Other oscillator features used in PIC18 enhanced microcontrollers, such as the internal RC oscillator and clock switching, remain the same. They are discussed later in this chapter. 2.1.1 OSCILLATOR CONTROL The operation of the oscillator in PIC18F2450/4450 devices is controlled through two Configuration registers and two control registers. Configuration registers, CONFIG1L and CONFIG1H, select the oscillator mode and USB prescaler/postscaler options. As Configuration bits, these are set when the device is programmed and left in that configuration until the device is reprogrammed. 2.2 Oscillator Types PIC18F2450/4450 devices can be operated in twelve distinct oscillator modes. In contrast with the non-USB PIC18 enhanced microcontrollers, four of these modes involve the use of two oscillator types at once. Users can program the FOSC3:FOSC0 Configuration bits to select one of these modes: 1. 2. 3. 4. XT XTPLL HS HSPLL Crystal/Resonator Crystal/Resonator with PLL Enabled High-Speed Crystal/Resonator High-Speed Crystal/Resonator with PLL Enabled 5. EC External Clock with FOSC/4 Output 6. ECIO External Clock with I/O on RA6 7. ECPLL External Clock with PLL Enabled and FOSC/4 Output on RA6 8. ECPIO External Clock with PLL Enabled, I/O on RA6 9. INTHS Internal Oscillator used as Microcontroller Clock Source, HS Oscillator used as USB Clock Source 10. INTXT Internal Oscillator used as Microcontroller Clock Source, XT Oscillator used as USB Clock Source 11. INTIO Internal Oscillator used as Microcontroller Clock Source, EC Oscillator used as USB Clock Source, Digital I/O on RA6 12. INTCKO Internal Oscillator used as Microcontroller Clock Source, EC Oscillator used as USB Clock Source, FOSC/4 Output on RA6 The OSCCON register (Register 2-1) selects the Active Clock mode; it is primarily used in controlling clock switching in power-managed modes. Its use is discussed in Section 2.4.1 “Oscillator Control Register”. © 2008 Microchip Technology Inc. DS39760D-page 23 PIC18F2450/4450 2.2.1 OSCILLATOR MODES AND USB OPERATION Because of the timing requirements imposed by USB, an internal clock of either 6 MHz or 48 MHz is required while the USB module is enabled. Fortunately, the microcontroller and other peripherals are not required to run at this clock speed when using the primary oscillator. There are numerous options to achieve the USB module clock requirement and still provide flexibility for clocking the rest of the device from the primary oscillator source. These are detailed in Section 2.3 “Oscillator Settings for USB”. Because of the unique requirements of the USB module, a different approach to clock operation is necessary. In previous PIC® microcontrollers, all core and peripheral clocks were driven by a single oscillator source; the usual sources were primary, secondary or the internal oscillator. With PIC18F2450/4450 devices, the primary oscillator becomes part of the USB module and cannot be associated to any other clock source. Thus, the USB module must be clocked from the primary clock source; however, the microcontroller core and other peripherals can be separately clocked from the secondary or internal oscillators as before. FIGURE 2-1: PIC18F2450/4450 CLOCK DIAGRAM PIC18F2450/4450 PLLDIV<2:0> ÷ 12 111 Sleep OSC1 110 ÷6 USBDIV 101 ÷5 100 ÷4 011 ÷3 (4 MHz Input Only) MUX Primary Oscillator PLL Prescaler ÷ 10 OSC2 USB Clock Source 96 MHz PLL 0 ÷2 1 010 ÷2 FSEN 001 ÷1 000 1 HSPLL, ECPLL, XTPLL, ECPIO USB Peripheral ÷4 ÷3 ÷2 ÷1 11 ÷6 ÷4 ÷3 ÷2 ÷4 11 0 10 01 00 10 CPU 1 0 01 Primary Clock FOSC3:FOSC0 00 Secondary Oscillator T1OSO T1OSI T1OSC IDLEN Peripherals MUX XT, HS, EC, ECIO Oscillator Postscaler CPUDIV<1:0> PLL Postscaler CPUDIV<1:0> T1OSCEN Enable Oscillator OSCCON<6:4> Internal RC Oscillator 31.25 kHz Internal Oscillator Clock Control FOSC3:FOSC0 OSCCON<1:0> Clock Source Option for Other Modules WDT, PWRT, FSCM and Two-Speed Start-up DS39760D-page 24 © 2008 Microchip Technology Inc. PIC18F2450/4450 2.2.2 CRYSTAL OSCILLATOR/CERAMIC RESONATORS In HS, HSPLL, XT and XTPLL Oscillator modes, a crystal or ceramic resonator is connected to the OSC1 and OSC2 pins to establish oscillation. Figure 2-2 shows the pin connections. The oscillator design requires the use of a parallel cut crystal. Note: Use of a series cut crystal may give a frequency out of the crystal manufacturer’s specifications. FIGURE 2-2: C1(1) CRYSTAL/CERAMIC RESONATOR OPERATION (XT, HS OR HSPLL CONFIGURATION) OSC1 XTAL RF(3) PIC18FXXXX OSC2 Note 1: See Table 2-1 and Table 2-2 for initial values of C1 and C2. 2: A series resistor (RS) may be required for AT strip cut crystals. 3: RF varies with the oscillator mode chosen. TABLE 2-1: CAPACITOR SELECTION FOR CERAMIC RESONATORS Typical Capacitor Values Used: Mode Freq OSC1 OSC2 XT 4.0 MHz 33 pF 33 pF HS 8.0 MHz 16.0 MHz 27 pF 22 pF 27 pF 22 pF Capacitor values are for design guidance only. These capacitors were tested with the resonators listed below for basic start-up and operation. These values are not optimized. Different capacitor values may be required to produce acceptable oscillator operation. The user should test the performance of the oscillator over the expected VDD and temperature range for the application. See the notes following Table 2-2 for additional information. Resonators Used: 4.0 MHz 8.0 MHz Osc Type CAPACITOR SELECTION FOR CRYSTAL OSCILLATOR Crystal Freq Typical Capacitor Values Tested: C1 C2 XT 4 MHz 27 pF 27 pF HS 4 MHz 27 pF 27 pF 8 MHz 22 pF 22 pF 20 MHz 15 pF 15 pF Capacitor values are for design guidance only. These capacitors were tested with the crystals listed below for basic start-up and operation. These values are not optimized. Different capacitor values may be required to produce acceptable oscillator operation. The user should test the performance of the oscillator over the expected VDD and temperature range for the application. See the notes following this table for additional information. Crystals Used: Sleep RS(2) C2(1) To Internal Logic TABLE 2-2: 4 MHz 8 MHz 20 MHz Note 1: Higher capacitance increases the stability of oscillator but also increases the start-up time. 2: When operating below 3V VDD, or when using certain ceramic resonators at any voltage, it may be necessary to use the HS mode or switch to a crystal oscillator. 3: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 4: Rs may be required to avoid overdriving crystals with low drive level specification. 5: Always verify oscillator performance over the VDD and temperature range that is expected for the application. An internal postscaler allows users to select a clock frequency other than that of the crystal or resonator. Frequency division is determined by the CPUDIV Configuration bits. Users may select a clock frequency of the oscillator frequency, or 1/2, 1/3 or 1/4 of the frequency. An external clock may also be used when the microcontroller is in HS Oscillator mode. In this case, the OSC2/CLKO pin is left open (Figure 2-3). 16.0 MHz © 2008 Microchip Technology Inc. DS39760D-page 25 PIC18F2450/4450 EXTERNAL CLOCK INPUT OPERATION (HS OSC CONFIGURATION) OSC1 Clock from Ext. System PIC18FXXXX Open 2.2.3 OSC2 (HS Mode) EXTERNAL CLOCK INPUT The EC, ECIO, ECPLL and ECPIO Oscillator modes require an external clock source to be connected to the OSC1 pin. There is no oscillator start-up time required after a Power-on Reset or after an exit from Sleep mode. In the EC and ECPLL Oscillator modes, the oscillator frequency divided by 4 is available on the OSC2 pin. This signal may be used for test purposes or to synchronize other logic. Figure 2-4 shows the pin connections for the EC Oscillator mode. FIGURE 2-4: EXTERNAL CLOCK INPUT OPERATION (EC AND ECPLL CONFIGURATION) OSC1/CLKI Clock from Ext. System 2.2.4 PLL FREQUENCY MULTIPLIER PIC18F2450/4450 devices include a Phase Locked Loop (PLL) circuit. This is provided specifically for USB applications with lower speed oscillators and can also be used as a microcontroller clock source. The PLL is enabled in HSPLL, XTPLL, ECPLL and ECPIO Oscillator modes. It is designed to produce a fixed 96 MHz reference clock from a fixed 4 MHz input. The output can then be divided and used for both the USB and the microcontroller core clock. Because the PLL has a fixed frequency input and output, there are eight prescaling options to match the oscillator input frequency to the PLL. There is also a separate postscaler option for deriving the microcontroller clock from the PLL. This allows the USB peripheral and microcontroller to use the same oscillator input and still operate at different clock speeds. In contrast to the postscaler for XT, HS and EC modes, the available options are 1/2, 1/3, 1/4 and 1/6 of the PLL output. The HSPLL, ECPLL and ECPIO modes make use of the HS mode oscillator for frequencies up to 48 MHz. The prescaler divides the oscillator input by up to 12 to produce the 4 MHz drive for the PLL. The XTPLL mode can only use an input frequency of 4 MHz which drives the PLL directly. FIGURE 2-6: PIC18FXXXX FOSC/4 OSC2/CLKO The ECIO and ECPIO Oscillator modes function like the EC and ECPLL modes, except that the OSC2 pin becomes an additional general purpose I/O pin. The I/O pin becomes bit 6 of PORTA (RA6). Figure 2-5 shows the pin connections for the ECIO Oscillator mode. FIGURE 2-5: EXTERNAL CLOCK INPUT OPERATION (ECIO AND ECPIO CONFIGURATION) OSC1/CLKI Clock from Ext. System PLL BLOCK DIAGRAM (HS MODE) HS/EC/ECIO/XT Oscillator Enable PLL Enable (from CONFIG1H Register) OSC2 OSC1 Oscillator and Prescaler FIN Phase Comparator FOUT Loop Filter ÷24 VCO MUX FIGURE 2-3: SYSCLK PIC18FXXXX RA6 I/O (OSC2) The internal postscaler for reducing clock frequency in XT and HS modes is also available in EC and ECIO modes. DS39760D-page 26 © 2008 Microchip Technology Inc. PIC18F2450/4450 2.2.5 INTERNAL OSCILLATOR The PIC18F2450/4450 devices include an internal RC oscillator (INTRC) which provides a nominal 31 kHz output. INTRC is enabled if it is selected as the device clock source; it is also enabled automatically when any of the following are enabled: • • • • Power-up Timer Fail-Safe Clock Monitor Watchdog Timer Two-Speed Start-up These features are discussed in greater detail in Section 18.0 “Special Features of the CPU”. 2.2.5.1 Internal Oscillator Modes When the internal oscillator is used as the microcontroller clock source, one of the other oscillator modes (External Clock or External Crystal/Resonator) must be used as the USB clock source. The choice of USB clock source is determined by the particular internal oscillator mode. There are four distinct modes available: 1. 2. 3. 4. INTHS mode: The USB clock is provided by the oscillator in HS mode. INTXT mode: The USB clock is provided by the oscillator in XT mode. INTCKO mode: The USB clock is provided by an external clock input on OSC1/CLKI; the OSC2/ CLKO pin outputs FOSC/4. INTIO mode: The USB clock is provided by an external clock input on OSC1/CLKI; the OSC2/ CLKO pin functions as a digital I/O (RA6). Of these four modes, only INTIO mode frees up an additional pin (OSC2/CLKO/RA6) for port I/O use. © 2008 Microchip Technology Inc. 2.3 Oscillator Settings for USB When the PIC18F2450/4450 is used for USB connectivity, it must have either a 6 MHz or 48 MHz clock for USB operation, depending on whether LowSpeed or Full-Speed mode is being used. This may require some forethought in selecting an oscillator frequency and programming the device. The full range of possible oscillator configurations compatible with USB operation is shown in Table 2-3. 2.3.1 LOW-SPEED OPERATION The USB clock for Low-Speed mode is derived from the primary oscillator chain and not directly from the PLL. It is divided by 4 to produce the actual 6 MHz clock. Because of this, the microcontroller can only use a clock frequency of 24 MHz when the USB module is active and the controller clock source is one of the primary oscillator modes (XT, HS or EC, with or without the PLL). This restriction does not apply if the microcontroller clock source is the secondary oscillator or internal oscillator. 2.3.2 RUNNING DIFFERENT USB AND MICROCONTROLLER CLOCKS The USB module, in either mode, can run asynchronously with respect to the microcontroller core and other peripherals. This means that applications can use the primary oscillator for the USB clock while the microcontroller runs from a separate clock source at a lower speed. If it is necessary to run the entire application from only one clock source, full-speed operation provides a greater selection of microcontroller clock frequencies. DS39760D-page 27 PIC18F2450/4450 TABLE 2-3: OSCILLATOR CONFIGURATION OPTIONS FOR USB OPERATION Input Oscillator Frequency 48 MHz PLL Division (PLLDIV2:PLLDIV0) N/A(1) Clock Mode (FOSC3:FOSC0) EC, ECIO EC, ECIO 48 MHz ÷12 (111) ECPLL, ECPIO EC, ECIO 40 MHz ÷10 (110) ECPLL, ECPIO HS, EC, ECIO 24 MHz ÷6 (101) HSPLL, ECPLL, ECPIO HS, EC, ECIO 20 MHz ÷5 (100) HSPLL, ECPLL, ECPIO HS, EC, ECIO 16 MHz ÷4 (011) HSPLL, ECPLL, ECPIO Legend: Note 1: MCU Clock Division (CPUDIV1:CPUDIV0) Microcontroller Clock Frequency None (00) 48 MHz ÷2 (01) 24 MHz ÷3 (10) 16 MHz ÷4 (11) 12 MHz None (00) 48 MHz ÷2 (01) 24 MHz ÷3 (10) 16 MHz ÷4 (11) 12 MHz ÷2 (00) 48 MHz ÷3 (01) 32 MHz ÷4 (10) 24 MHz ÷6 (11) 16 MHz None (00) 40 MHz ÷2 (01) 20 MHz ÷3 (10) 13.33 MHz ÷4 (11) 10 MHz ÷2 (00) 48 MHz ÷3 (01) 32 MHz ÷4 (10) 24 MHz ÷6 (11) 16 MHz None (00) 24 MHz ÷2 (01) 12 MHz ÷3 (10) 8 MHz ÷4 (11) 6 MHz ÷2 (00) 48 MHz ÷3 (01) 32 MHz ÷4 (10) 24 MHz ÷6 (11) 16 MHz None (00) 20 MHz ÷2 (01) 10 MHz ÷3 (10) 6.67 MHz ÷4 (11) 5 MHz ÷2 (00) 48 MHz ÷3 (01) 32 MHz ÷4 (10) 24 MHz ÷6 (11) 16 MHz None (00) 16 MHz ÷2 (01) 8 MHz ÷3 (10) 5.33 MHz ÷4 (11) 4 MHz ÷2 (00) 48 MHz ÷3 (01) 32 MHz ÷4 (10) 24 MHz ÷6 (11) 16 MHz All clock frequencies, except 24 MHz, are exclusively associated with full-speed USB operation (USB clock of 48 MHz). Bold is used to highlight clock selections that are compatible with low-speed USB operation (system clock of 24 MHz, USB clock of 6 MHz). Only valid when the USBDIV Configuration bit is cleared. DS39760D-page 28 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 2-3: OSCILLATOR CONFIGURATION OPTIONS FOR USB OPERATION (CONTINUED) Input Oscillator Frequency PLL Division (PLLDIV2:PLLDIV0) Clock Mode (FOSC3:FOSC0) HS, EC, ECIO 12 MHz ÷3 (010) HSPLL, ECPLL, ECPIO HS, EC, ECIO 8 MHz ÷2 (001) HSPLL, ECPLL, ECPIO XT, HS, EC, ECIO 4 MHz ÷1 (000) HSPLL, ECPLL, XTPLL, ECPIO Legend: Note 1: MCU Clock Division (CPUDIV1:CPUDIV0) Microcontroller Clock Frequency None (00) 12 MHz ÷2 (01) 6 MHz ÷3 (10) 4 MHz ÷4 (11) 3 MHz ÷2 (00) 48 MHz ÷3 (01) 32 MHz ÷4 (10) 24 MHz ÷6 (11) 16 MHz None (00) 8 MHz ÷2 (01) 4 MHz ÷3 (10) 2.67 MHz ÷4 (11) 2 MHz ÷2 (00) 48 MHz ÷3 (01) 32 MHz ÷4 (10) 24 MHz ÷6 (11) 16 MHz None (00) 4 MHz ÷2 (01) 2 MHz ÷3 (10) 1.33 MHz ÷4 (11) 1 MHz ÷2 (00) 48 MHz ÷3 (01) 32 MHz ÷4 (10) 24 MHz ÷6 (11) 16 MHz All clock frequencies, except 24 MHz, are exclusively associated with full-speed USB operation (USB clock of 48 MHz). Bold is used to highlight clock selections that are compatible with low-speed USB operation (system clock of 24 MHz, USB clock of 6 MHz). Only valid when the USBDIV Configuration bit is cleared. © 2008 Microchip Technology Inc. DS39760D-page 29 PIC18F2450/4450 2.4 Clock Sources and Oscillator Switching Like previous PIC18 enhanced devices, the PIC18F2450/4450 family includes a feature that allows the device clock source to be switched from the main oscillator to an alternate, low-frequency clock source. PIC18F2450/4450 devices offer two alternate clock sources. When an alternate clock source is enabled, the various power-managed operating modes are available. Essentially, there are three clock sources for these devices: • Primary oscillators • Secondary oscillators • Internal oscillator The primary oscillators include the External Crystal and Resonator modes, the External Clock modes and the internal oscillator. The particular mode is defined by the FOSC3:FOSC0 Configuration bits. The details of these modes are covered earlier in this chapter. The secondary oscillators are those external sources not connected to the OSC1 or OSC2 pins. These sources may continue to operate even after the controller is placed in a power-managed mode. PIC18F2450/4450 devices offer the Timer1 oscillator as a secondary oscillator. This oscillator, in all powermanaged modes, is often the time base for functions such as a Real-Time Clock (RTC). Most often, a 32.768 kHz watch crystal is connected between the RC0/T1OSO/T1CKI and RC1/T1OSI/UOE pins. Like the XT and HS Oscillator mode circuits, loading capacitors are also connected from each pin to ground. The Timer1 oscillator is discussed in greater detail in Section 11.3 “Timer1 Oscillator”. In addition to being a primary clock source, the internal oscillator is available as a power-managed mode clock source. The INTRC source is also used as the clock source for several special features, such as the WDT and Fail-Safe Clock Monitor. 2.4.1 OSCILLATOR CONTROL REGISTER The OSCCON register (Register 2-1) controls several aspects of the device clock’s operation, both in full-power operation and in power-managed modes. INTRC always remains the clock source for features such as the Watchdog Timer and the Fail-Safe Clock Monitor. The OSTS and T1RUN bits indicate which clock source is currently providing the device clock. The OSTS bit indicates that the Oscillator Start-up Timer (OST) has timed out and the primary clock is providing the device clock in primary clock modes. The T1RUN bit (T1CON<6>) indicates when the Timer1 oscillator is providing the device clock in secondary clock modes. In power-managed modes, only one of these three bits will be set at any time. If none of these bits are set, the INTRC is providing the clock or the internal oscillator has just started and is not yet stable. The IDLEN bit determines if the device goes into Sleep mode, or one of the Idle modes, when the SLEEP instruction is executed. The use of the flag and control bits in the OSCCON register is discussed in more detail in Section 3.0 “Power-Managed Modes”. Note 1: The Timer1 oscillator must be enabled to select the secondary clock source. The Timer1 oscillator is enabled by setting the T1OSCEN bit in the Timer1 Control register (T1CON<3>). If the Timer1 oscillator is not enabled, then any attempt to select a secondary clock source will be ignored. 2: It is recommended that the Timer1 oscillator be operating and stable prior to switching to it as the clock source; otherwise, a very long delay may occur while the Timer1 oscillator starts. 2.4.2 OSCILLATOR TRANSITIONS PIC18F2450/4450 devices contain circuitry to prevent clock “glitches” when switching between clock sources. A short pause in the device clock occurs during the clock switch. The length of this pause is the sum of two cycles of the old clock source and three to four cycles of the new clock source. This formula assumes that the new clock source is stable. Clock transitions are discussed in greater detail in Section 3.1.2 “Entering Power-Managed Modes”. The System Clock Select bits, SCS1:SCS0, select the clock source. The available clock sources are the primary clock (defined by the FOSC3:FOSC0 Configuration bits), the secondary clock (Timer1 oscillator) and the internal oscillator. The clock source changes immediately, after one or more of the bits is written to, following a brief clock transition interval. The SCS bits are cleared on all forms of Reset. DS39760D-page 30 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 2-1: OSCCON: OSCILLATOR CONTROL REGISTER R/W-0 U-0 U-0 U-0 R(1) U-0 R/W-0 R/W-0 IDLEN — — — OSTS — SCS1 SCS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 IDLEN: Idle Enable bit 1 = Device enters Idle mode on SLEEP instruction 0 = Device enters Sleep mode on SLEEP instruction bit 6-4 Unimplemented: Read as ‘0’ bit 3 OSTS: Oscillator Start-up Time-out Status bit(1) 1 = Oscillator Start-up Timer time-out has expired; primary oscillator is running 0 = Oscillator Start-up Timer time-out is running; primary oscillator is not ready bit 2 Unimplemented: Read as ‘0’ bit 1-0 SCS1:SCS0: System Clock Select bits 1x = Internal oscillator 01 = Timer1 oscillator 00 = Primary oscillator Note 1: Depends on the state of the IESO Configuration bit. © 2008 Microchip Technology Inc. DS39760D-page 31 PIC18F2450/4450 2.5 Effects of Power-Managed Modes on the Various Clock Sources When PRI_IDLE mode is selected, the designated primary oscillator continues to run without interruption. For all other power-managed modes, the oscillator using the OSC1 pin is disabled. Unless the USB module is enabled, the OSC1 pin (and OSC2 pin if used by the oscillator) will stop oscillating. In secondary clock modes (SEC_RUN and SEC_IDLE), the Timer1 oscillator is operating and providing the device clock. The Timer1 oscillator may also run in all power-managed modes if required to clock Timer1. In internal oscillator modes (RC_RUN and RC_IDLE), the internal oscillator provides the device clock source. The 31 kHz INTRC output can be used directly to provide the clock and may be enabled to support various special features regardless of the power-managed mode (see Section 18.2 “Watchdog Timer (WDT)”, Section 18.3 “Two-Speed Start-up” and Section 18.4 “Fail-Safe Clock Monitor” for more information on WDT, Fail-Safe Clock Monitor and Two-Speed Start-up). Regardless of the Run or Idle mode selected, the USB clock source will continue to operate. If the device is operating from a crystal or resonator-based oscillator, that oscillator will continue to clock the USB module. The core and all other modules will switch to the new clock source. If the Sleep mode is selected, all clock sources are stopped. Since all the transistor switching currents have been stopped, Sleep mode achieves the lowest current consumption of the device (only leakage currents). Sleep mode should never be invoked while the USB module is operating and connected. The only exception is when the device has been issued a “Suspend” command over the USB. Once the module has suspended operation and shifted to a low-power state, the microcontroller may be safely put into Sleep mode. TABLE 2-4: Enabling any on-chip feature that will operate during Sleep will increase the current consumed during Sleep. The INTRC is required to support WDT operation. The Timer1 oscillator may be operating to support a RealTime Clock. Other features may be operating that do not require a device clock source (i.e., PSP, INTx pins and others). Peripherals that may add significant current consumption are listed in Section 21.2 “DC Characteristics: Power-Down and Supply Current”. 2.6 Power-up Delays Power-up delays are controlled by two timers, so that no external Reset circuitry is required for most applications. The delays ensure that the device is kept in Reset until the device power supply is stable under normal circumstances and the primary clock is operating and stable. For additional information on power-up delays, see Section 4.5 “Device Reset Timers”. The first timer is the Power-up Timer (PWRT), which provides a fixed delay on power-up (parameter 33, Table 21-10). It is enabled by clearing (= 0) the PWRTEN Configuration bit. The second timer is the Oscillator Start-up Timer (OST), intended to keep the chip in Reset until the crystal oscillator is stable (XT and HS modes). The OST does this by counting 1024 oscillator cycles before allowing the oscillator to clock the device. When the HSPLL Oscillator mode is selected, the device is kept in Reset for an additional 2 ms following the HS mode OST delay, so the PLL can lock to the incoming clock frequency. There is a delay of interval, TCSD (parameter 38, Table 21-10), following POR, while the controller becomes ready to execute instructions. This delay runs concurrently with any other delays. This may be the only delay that occurs when any of the EC or internal oscillator modes are used as the primary clock source. OSC1 AND OSC2 PIN STATES IN SLEEP MODE Oscillator Mode OSC1 Pin OSC2 Pin INTCKO Floating, pulled by external clock At logic low (clock/4 output) INTIO Floating, pulled by external clock Configured as PORTA, bit 6 ECIO, ECPIO Floating, pulled by external clock Configured as PORTA, bit 6 EC Floating, pulled by external clock At logic low (clock/4 output) XT and HS Feedback inverter disabled at quiescent voltage level Feedback inverter disabled at quiescent voltage level Note: See Table 4-2 in Section 4.0 “Reset” for time-outs due to Sleep and MCLR Reset. DS39760D-page 32 © 2008 Microchip Technology Inc. PIC18F2450/4450 3.0 POWER-MANAGED MODES 3.1.1 PIC18F2450/4450 devices offer a total of seven operating modes for more efficient power management. These modes provide a variety of options for selective power conservation in applications where resources may be limited (i.e., battery-powered devices). There are three categories of power-managed modes: • Run modes • Idle modes • Sleep mode These categories define which portions of the device are clocked and sometimes, what speed. The Run and Idle modes may use any of the three available clock sources (primary, secondary or internal oscillator); the Sleep mode does not use a clock source. The power-managed modes include several powersaving features offered on previous PIC® microcontrollers. One is the clock switching feature, offered in other PIC18 devices, allowing the controller to use the Timer1 oscillator in place of the primary oscillator. Also included is the Sleep mode, offered by all PIC microcontrollers, where all device clocks are stopped. 3.1 Selecting Power-Managed Modes Selecting a power-managed mode requires two decisions: if the CPU is to be clocked or not and the selection of a clock source. The IDLEN bit (OSCCON<7>) controls CPU clocking, while the SCS1:SCS0 bits (OSCCON<1:0>) select the clock source. The individual modes, bit settings, clock sources and affected modules are summarized in Table 3-1. TABLE 3-1: The SCS1:SCS0 bits allow the selection of one of three clock sources for power-managed modes. They are: • The primary clock, as defined by the FOSC3:FOSC0 Configuration bits • The secondary clock (the Timer1 oscillator) • The internal oscillator (for RC modes) 3.1.2 ENTERING POWER-MANAGED MODES Switching from one power-managed mode to another begins by loading the OSCCON register. The SCS1:SCS0 bits select the clock source and determine which Run or Idle mode is to be used. Changing these bits causes an immediate switch to the new clock source, assuming that it is running. The switch may also be subject to clock transition delays. These are discussed in Section 3.1.3 “Clock Transitions and Status Indicators” and subsequent sections. Entry to the power-managed Idle or Sleep modes is triggered by the execution of a SLEEP instruction. The actual mode that results depends on the status of the IDLEN bit. Depending on the current mode and the mode being switched to, a change to a power-managed mode does not always require setting all of these bits. Many transitions may be done by changing the oscillator select bits, or changing the IDLEN bit, prior to issuing a SLEEP instruction. If the IDLEN bit is already configured correctly, it may only be necessary to perform a SLEEP instruction to switch to the desired mode. POWER-MANAGED MODES OSCCON Bits Mode CLOCK SOURCES Module Clocking Available Clock and Oscillator Source IDLEN(1) SCS1:SCS0 CPU Peripherals 0 N/A Off Off PRI_RUN N/A 00 Clocked Clocked Primary – all oscillator modes. This is the normal full-power execution mode. SEC_RUN N/A 01 Clocked Clocked Secondary – Timer1 oscillator RC_RUN N/A 1x Clocked Clocked Internal oscillator(2) PRI_IDLE 1 00 Off Clocked Primary – all oscillator modes SEC_IDLE 1 01 Off Clocked Secondary – Timer1 oscillator RC_IDLE 1 1x Off Clocked Internal oscillator(2) Sleep Note 1: 2: None – all clocks are disabled IDLEN reflects its value when the SLEEP instruction is executed. Clock is INTRC source. © 2008 Microchip Technology Inc. DS39760D-page 33 PIC18F2450/4450 3.1.3 CLOCK TRANSITIONS AND STATUS INDICATORS The length of the transition between clock sources is the sum of two cycles of the old clock source and three to four cycles of the new clock source. This formula assumes that the new clock source is stable. Two bits indicate the current clock source and its status. They are: • OSTS (OSCCON<3>) • T1RUN (T1CON<6>) In general, only one of these bits will be set while in a given power-managed mode. When the OSTS bit is set, the primary clock is providing the device clock. When the T1RUN bit is set, the Timer1 oscillator is providing the clock. Note: 3.1.4 Executing a SLEEP instruction does not necessarily place the device into Sleep mode. It acts as the trigger to place the controller into either the Sleep mode, or one of the Idle modes, depending on the setting of the IDLEN bit. MULTIPLE SLEEP COMMANDS The power-managed mode that is invoked with the SLEEP instruction is determined by the setting of the IDLEN bit at the time the instruction is executed. If another SLEEP instruction is executed, the device will enter the power-managed mode specified by IDLEN at that time. If IDLEN has changed, the device will enter the new power-managed mode specified by the new setting. 3.2 3.2.1 PRI_RUN MODE The PRI_RUN mode is the normal, full-power execution mode of the microcontroller. This is also the default mode upon a device Reset unless Two-Speed Start-up is enabled (see Section 18.3 “Two-Speed Start-up” for details). In this mode, the OSTS bit is set. 3.2.2 SEC_RUN MODE The SEC_RUN mode is the compatible mode to the “clock switching” feature offered in other PIC18 devices. In this mode, the CPU and peripherals are clocked from the Timer1 oscillator. This gives users the option of lower power consumption while still using a high accuracy clock source. SEC_RUN mode is entered by setting the SCS1:SCS0 bits to ‘01’. The device clock source is switched to the Timer1 oscillator (see Figure 3-1), the primary oscillator is shut down, the T1RUN bit (T1CON<6>) is set and the OSTS bit is cleared. Note: The Timer1 oscillator should already be running prior to entering SEC_RUN mode. If the T1OSCEN bit is not set when the SCS1:SCS0 bits are set to ‘01’, entry to SEC_RUN mode will not occur. If the Timer1 oscillator is enabled but not yet running, device clocks will be delayed until the oscillator has started. In such situations, initial oscillator operation is far from stable and unpredictable operation may result. Run Modes In the Run modes, clocks to both the core and peripherals are active. The difference between these modes is the clock source. DS39760D-page 34 © 2008 Microchip Technology Inc. PIC18F2450/4450 On transitions from SEC_RUN mode to PRI_RUN mode, the peripherals and CPU continue to be clocked from the Timer1 oscillator while the primary clock is started. When the primary clock becomes ready, a clock switch back to the primary clock occurs (see FIGURE 3-1: Figure 3-2). When the clock switch is complete, the T1RUN bit is cleared, the OSTS bit is set and the primary clock is providing the clock. The IDLEN and SCS bits are not affected by the wake-up; the Timer1 oscillator continues to run. TRANSITION TIMING FOR ENTRY TO SEC_RUN MODE Q1 Q2 Q3 Q4 Q1 Q2 1 T1OSI 2 3 n-1 Q3 Q4 Q1 Q2 Q3 n Clock Transition(1) OSC1 CPU Clock Peripheral Clock Program Counter Note 1: PC PC + 2 PC + 4 Clock transition typically occurs within 2-4 TOSC. FIGURE 3-2: TRANSITION TIMING FROM SEC_RUN MODE TO PRI_RUN MODE (HSPLL) Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 T1OSI OSC1 TOST(1) TPLL(1) 1 PLL Clock Output 2 n-1 n Clock(2) Transition CPU Clock Peripheral Clock Program Counter SCS1:SCS0 bits Changed Note PC + 2 PC OSTS bit Set 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale. 2: Clock transition typically occurs within 2-4 TOSC. © 2008 Microchip Technology Inc. PC + 4 DS39760D-page 35 PIC18F2450/4450 3.2.3 RC_RUN MODE This mode is entered by setting SCS1 to ‘1’. Although it is ignored, it is recommended that SCS0 also be cleared; this is to maintain software compatibility with future devices. When the clock source is switched to the INTRC (see Figure 3-3), the primary oscillator is shut down and the OSTS bit is cleared. In RC_RUN mode, the CPU and peripherals are clocked from the internal oscillator; the primary clock is shut down. When using the INTRC source, this mode provides the best power conservation of all the Run modes while still executing code. It works well for user applications which are not highly timing sensitive or do not require high-speed clocks at all times. On transitions from RC_RUN mode to PRI_RUN mode, the device continues to be clocked from the INTRC while the primary clock is started. When the primary clock becomes ready, a clock switch to the primary clock occurs (see Figure 3-4). When the clock switch is complete, the OSTS bit is set and the primary clock is providing the device clock. The IDLEN and SCS bits are not affected by the switch. The INTRC source will continue to run if either the WDT or the Fail-Safe Clock Monitor is enabled. If the primary clock source is the internal oscillator (INTRC), there are no distinguishable differences between the PRI_RUN and RC_RUN modes during execution. However, a clock switch delay will occur during entry to and exit from RC_RUN mode. Therefore, if the primary clock source is the internal oscillator, the use of RC_RUN mode is not recommended. FIGURE 3-3: TRANSITION TIMING TO RC_RUN MODE Q1 Q2 Q3 Q4 Q1 Q2 1 INTRC 2 3 n-1 Q3 Q4 Q1 Q2 Q3 n Clock Transition(1) OSC1 CPU Clock Peripheral Clock Program Counter Note 1: PC PC + 2 PC + 4 Clock transition typically occurs within 2-4 TOSC. FIGURE 3-4: TRANSITION TIMING FROM RC_RUN MODE TO PRI_RUN MODE Q1 Q2 Q3 Q4 Q2 Q3 Q4 Q1 Q2 Q3 Q1 INTRC OSC1 TOST(1) TPLL(1) 1 PLL Clock Output 2 n-1 n Clock(2) Transition CPU Clock Peripheral Clock Program Counter PC SCS1:SCS0 bits Changed Note PC + 2 OSTS bit Set 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale. 2: Clock transition typically occurs within 2-4 TOSC. DS39760D-page 36 PC + 4 © 2008 Microchip Technology Inc. PIC18F2450/4450 3.3 Sleep Mode 3.4 The power-managed Sleep mode in the PIC18F2450/ 4450 devices is identical to the legacy Sleep mode offered in all other PIC microcontrollers. It is entered by clearing the IDLEN bit (the default state on device Reset) and executing the SLEEP instruction. This shuts down the selected oscillator (Figure 3-5). All clock source status bits are cleared. Idle Modes The Idle modes allow the controller’s CPU to be selectively shut down while the peripherals continue to operate. Selecting a particular Idle mode allows users to further manage power consumption. If the IDLEN bit is set to ‘1’ when a SLEEP instruction is executed, the peripherals will be clocked from the clock source selected using the SCS1:SCS0 bits; however, the CPU will not be clocked. The clock source status bits are not affected. Setting IDLEN and executing a SLEEP instruction provides a quick method of switching from a given Run mode to its corresponding Idle mode. Entering the Sleep mode from any other mode does not require a clock switch. This is because no clocks are needed once the controller has entered Sleep. If the WDT is selected, the INTRC source will continue to operate. If the Timer1 oscillator is enabled, it will also continue to run. If the WDT is selected, the INTRC source will continue to operate. If the Timer1 oscillator is enabled, it will also continue to run. When a wake event occurs in Sleep mode (by interrupt, Reset or WDT time-out), the device will not be clocked until the clock source selected by the SCS1:SCS0 bits becomes ready (see Figure 3-6), or it will be clocked from the internal oscillator if either the Two-Speed Start-up or the Fail-Safe Clock Monitor are enabled (see Section 18.0 “Special Features of the CPU”). In either case, the OSTS bit is set when the primary clock is providing the device clocks. The IDLEN and SCS bits are not affected by the wake-up. Since the CPU is not executing instructions, the only exits from any of the Idle modes are by interrupt, WDT time-out or a Reset. When a wake event occurs, CPU execution is delayed by an interval of TCSD (parameter 38, Table 21-10) while it becomes ready to execute code. When the CPU begins executing code, it resumes with the same clock source for the current Idle mode. For example, when waking from RC_IDLE mode, the internal oscillator will clock the CPU and peripherals (in other words, RC_RUN mode). The IDLEN and SCS bits are not affected by the wake-up. While in any Idle mode or Sleep mode, a WDT time-out will result in a WDT wake-up to the Run mode currently specified by the SCS1:SCS0 bits. FIGURE 3-5: TRANSITION TIMING FOR ENTRY TO SLEEP MODE Q1 Q2 Q3 Q4 Q1 OSC1 CPU Clock Peripheral Clock Sleep Program Counter PC FIGURE 3-6: PC + 2 TRANSITION TIMING FOR WAKE FROM SLEEP (HSPLL) Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 OSC1 PLL Clock Output TOST(1) TPLL(1) CPU Clock Peripheral Clock Program Counter PC Wake Event PC + 2 PC + 4 PC + 6 OSTS bit Set Note 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale. © 2008 Microchip Technology Inc. DS39760D-page 37 PIC18F2450/4450 3.4.1 PRI_IDLE MODE 3.4.2 This mode is unique among the three low-power Idle modes in that it does not disable the primary device clock. For timing sensitive applications, this allows for the fastest resumption of device operation, with its more accurate primary clock source, since the clock source does not have to “warm up” or transition from another oscillator. PRI_IDLE mode is entered from PRI_RUN mode by setting the IDLEN bit and executing a SLEEP instruction. If the device is in another Run mode, set IDLEN first, then clear the SCS bits and execute SLEEP. Although the CPU is disabled, the peripherals continue to be clocked from the primary clock source specified by the FOSC3:FOSC0 Configuration bits. The OSTS bit remains set (see Figure 3-7). In SEC_IDLE mode, the CPU is disabled but the peripherals continue to be clocked from the Timer1 oscillator. This mode is entered from SEC_RUN by setting the IDLEN bit and executing a SLEEP instruction. If the device is in another Run mode, set IDLEN first, then set SCS1:SCS0 to ‘01’ and execute SLEEP. When the clock source is switched to the Timer1 oscillator, the primary oscillator is shut down, the OSTS bit is cleared and the T1RUN bit is set. When a wake event occurs, the peripherals continue to be clocked from the Timer1 oscillator. After an interval of TCSD following the wake event, the CPU begins executing code being clocked by the Timer1 oscillator. The IDLEN and SCS bits are not affected by the wake-up; the Timer1 oscillator continues to run (see Figure 3-8). When a wake event occurs, the CPU is clocked from the primary clock source. A delay of interval TCSD is required between the wake event and when code execution starts. This is required to allow the CPU to become ready to execute instructions. After the wakeup, the OSTS bit remains set. The IDLEN and SCS bits are not affected by the wake-up (see Figure 3-8). FIGURE 3-7: SEC_IDLE MODE Note: The Timer1 oscillator should already be running prior to entering SEC_IDLE mode. If the T1OSCEN bit is not set when the SLEEP instruction is executed, the SLEEP instruction will be ignored and entry to SEC_IDLE mode will not occur. If the Timer1 oscillator is enabled but not yet running, peripheral clocks will be delayed until the oscillator has started. In such situations, initial oscillator operation is far from stable and unpredictable operation may result. TRANSITION TIMING FOR ENTRY TO IDLE MODE Q1 Q4 Q3 Q2 Q1 OSC1 CPU Clock Peripheral Clock Program Counter PC FIGURE 3-8: PC + 2 TRANSITION TIMING FOR WAKE FROM IDLE TO RUN MODE Q1 Q2 Q3 Q4 OSC1 TCSD CPU Clock Peripheral Clock Program Counter PC Wake Event DS39760D-page 38 © 2008 Microchip Technology Inc. PIC18F2450/4450 3.4.3 RC_IDLE MODE In RC_IDLE mode, the CPU is disabled but the peripherals continue to be clocked from the internal oscillator, INTRC. This mode allows for controllable power conservation during Idle periods. From RC_RUN, this mode is entered by setting the IDLEN bit and executing a SLEEP instruction. If the device is in another Run mode, first set IDLEN, then set the SCS1 bit and execute SLEEP. Although its value is ignored, it is recommended that SCS0 also be cleared; this is to maintain software compatibility with future devices. When the clock source is switched to the INTRC, the primary oscillator is shut down and the OSTS bit is cleared. When a wake event occurs, the peripherals continue to be clocked from the INTRC. After a delay of TCSD following the wake event, the CPU begins executing code being clocked by the INTRC. The IDLEN and SCS bits are not affected by the wake-up. The INTRC source will continue to run if either the WDT or the Fail-Safe Clock Monitor is enabled. 3.5 Exiting Idle and Sleep Modes An exit from Sleep mode or any of the Idle modes is triggered by an interrupt, a Reset or a WDT time-out. This section discusses the triggers that cause exits from power-managed modes. The clocking subsystem actions are discussed in each of the power-managed modes (see Section 3.2 “Run Modes”, Section 3.3 “Sleep Mode” and Section 3.4 “Idle Modes”). 3.5.1 EXIT BY INTERRUPT Any of the available interrupt sources can cause the device to exit from an Idle mode, or the Sleep mode, to a Run mode. To enable this functionality, an interrupt source must be enabled by setting its enable bit in one of the INTCON or PIE registers. The exit sequence is initiated when the corresponding interrupt flag bit is set. A fixed delay of interval, TCSD, following the wake event, is required when leaving Sleep and Idle modes. This delay is required for the CPU to prepare for execution. Instruction execution resumes on the first clock cycle following this delay. 3.5.2 EXIT BY WDT TIME-OUT A WDT time-out will cause different actions depending on which power-managed mode the device is in when the time-out occurs. If the device is not executing code (all Idle modes and Sleep mode), the time-out will result in an exit from the power-managed mode (see Section 3.2 “Run Modes” and Section 3.3 “Sleep Mode”). If the device is executing code (all Run modes), the time-out will result in a WDT Reset (see Section 18.2 “Watchdog Timer (WDT)”). 3.5.3 EXIT BY RESET Normally, the device is held in Reset by the Oscillator Start-up Timer (OST) until the primary clock becomes ready. At that time, the OSTS bit is set and the device begins executing code. The exit delay time from Reset to the start of code execution depends on both the clock sources before and after the wake-up and the type of oscillator if the new clock source is the primary clock. Exit delays are summarized in Table 3-2. Code execution can begin before the primary clock becomes ready. If either the Two-Speed Start-up (see Section 18.3 “Two-Speed Start-up”) or Fail-Safe Clock Monitor (see Section 18.4 “Fail-Safe Clock Monitor”) is enabled, the device may begin execution as soon as the Reset source has cleared. Execution is clocked by the INTRC driven by the internal oscillator. Execution is clocked by the internal oscillator until either the primary clock becomes ready or a powermanaged mode is entered before the primary clock becomes ready; the primary clock is then shut down. On all exits from Idle or Sleep modes by interrupt, code execution branches to the interrupt vector if the GIE/ GIEH bit (INTCON<7>) is set. Otherwise, code execution continues or resumes without branching (see Section 8.0 “Interrupts”). © 2008 Microchip Technology Inc. DS39760D-page 39 PIC18F2450/4450 3.5.4 EXIT WITHOUT AN OSCILLATOR START-UP DELAY Certain exits from power-managed modes do not invoke the OST at all. There are two cases: • PRI_IDLE mode, where the primary clock source is not stopped; and • The primary clock source is not any of the XT or HS modes TABLE 3-2: In these instances, the primary clock source either does not require an oscillator start-up delay, since it is already running (PRI_IDLE), or normally does not require an oscillator start-up delay (EC and any internal oscillator modes). However, a fixed delay of interval TCSD following the wake event is still required when leaving Sleep and Idle modes to allow the CPU to prepare for execution. Instruction execution resumes on the first clock cycle following this delay. EXIT DELAY ON WAKE-UP BY RESET FROM SLEEP MODE OR ANY IDLE MODE (BY CLOCK SOURCES) Microcontroller Clock Source Before Wake-up After Wake-up Primary Device Clock (PRI_IDLE mode) XTPLL, HSPLL Exit Delay Clock Ready Status Bit (OSCCON) None OSTS XT, HS EC INTRC(1) T1OSC or INTRC(1) INTRC(1) None (Sleep mode) Note 1: 2: 3: 4: XT, HS TOST(3) XTPLL, HSPLL TOST + trc(3) EC TCSD(2) INTRC(1) TIOBST(4) XT, HS TOST(3) XTPLL, HSPLL TOST + trc(3) EC TCSD(2) INTRC(1) None XT, HS TOST(3) XTPLL, HSPLL TOST + trc(3) EC TCSD(2) INTRC(1) TIOBST(4) OSTS OSTS OSTS In this instance, refers specifically to the 31 kHz INTRC clock source. TCSD (parameter 38, Table 21-10) is a required delay when waking from Sleep and all Idle modes and runs concurrently with any other required delays (see Section 3.4 “Idle Modes”). TOST is the Oscillator Start-up Timer period (parameter 32, Table 21-10). trc is the PLL lock time-out (parameter F12, Table 21-7); it is also designated as TPLL. Execution continues during TIOBST (parameter 39, Table 21-10), the INTRC stabilization period. DS39760D-page 40 © 2008 Microchip Technology Inc. PIC18F2450/4450 4.0 RESET The PIC18F2450/4450 devices differentiate between various kinds of Reset: a) b) c) d) e) f) g) h) Power-on Reset (POR) MCLR Reset during normal operation MCLR Reset during power-managed modes Watchdog Timer (WDT) Reset (during execution) Programmable Brown-out Reset (BOR) RESET Instruction Stack Full Reset Stack Underflow Reset This section discusses Resets generated by MCLR, POR and BOR, and covers the operation of the various start-up timers. Stack Reset events are covered in Section 5.1.2.4 “Stack Full and Underflow Resets”. WDT Resets are covered in Section 18.2 “Watchdog Timer (WDT)”. FIGURE 4-1: A simplified block diagram of the on-chip Reset circuit is shown in Figure 4-1. 4.1 RCON Register Device Reset events are tracked through the RCON register (Register 4-1). The lower five bits of the register indicate that a specific Reset event has occurred. In most cases, these bits can only be cleared by the event and must be set by the application after the event. The state of these flag bits, taken together, can be read to indicate the type of Reset that just occurred. This is described in more detail in Section 4.6 “Reset State of Registers”. The RCON register also has control bits for setting interrupt priority (IPEN) and software control of the BOR (SBOREN). Interrupt priority is discussed in Section 8.0 “Interrupts”. BOR is covered in Section 4.4 “Brown-out Reset (BOR)”. SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT RESET Instruction Stack Full/Underflow Reset Stack Pointer External Reset MCLR MCLRE ( )_IDLE Sleep WDT Time-out VDD Rise Detect POR Pulse VDD Brown-out Reset BOREN S OST/PWRT OST 1024 Cycles 10-Bit Ripple Counter OSC1 32 μs INTRC(1) PWRT Chip_Reset R Q 65.5 ms 11-Bit Ripple Counter Enable PWRT Enable OST(2) Note 1: 2: This is the INTRC source from the internal oscillator and is separate from the RC oscillator of the CLKI pin. See Table 4-2 for time-out situations. © 2008 Microchip Technology Inc. DS39760D-page 41 PIC18F2450/4450 REGISTER 4-1: RCON: RESET CONTROL REGISTER R/W-0 R/W-1(1) U-0 R/W-1 R-1 R-1 R/W-0(2) R/W-0 IPEN SBOREN — RI TO PD POR BOR bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 IPEN: Interrupt Priority Enable bit 1 = Enable priority levels on interrupts 0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode) bit 6 SBOREN: BOR Software Enable bit(1) If BOREN1:BOREN0 = 01: 1 = BOR is enabled 0 = BOR is disabled If BOREN1:BOREN0 = 00, 10 or 11: Bit is disabled and read as ‘0’. bit 5 Unimplemented: Read as ‘0’ bit 4 RI: RESET Instruction Flag bit 1 = The RESET instruction was not executed (set by firmware only) 0 = The RESET instruction was executed causing a device Reset (must be set in software after a Brown-out Reset occurs) bit 3 TO: Watchdog Time-out Flag bit 1 = Set by power-up, CLRWDT instruction or SLEEP instruction 0 = A WDT time-out occurred bit 2 PD: Power-Down Detection Flag bit 1 = Set by power-up or by the CLRWDT instruction 0 = Set by execution of the SLEEP instruction bit 1 POR: Power-on Reset Status bit(2) 1 = A Power-on Reset has not occurred (set by firmware only) 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) bit 0 BOR: Brown-out Reset Status bit 1 = A Brown-out Reset has not occurred (set by firmware only) 0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs) Note 1: 2: If SBOREN is enabled, its Reset state is ‘1’; otherwise, it is ‘0’. The actual Reset value of POR is determined by the type of device Reset. See the notes following this register and Section 4.6 “Reset State of Registers” for additional information. Note 1: It is recommended that the POR bit be set after a Power-on Reset has been detected so that subsequent Power-on Resets may be detected. 2: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming that POR was set to ‘1’ by software immediately after a Power-on Rest). DS39760D-page 42 © 2008 Microchip Technology Inc. PIC18F2450/4450 4.2 Master Clear Reset (MCLR) The MCLR pin provides a method for triggering an external Reset of the device. A Reset is generated by holding the pin low. These devices have a noise filter in the MCLR Reset path which detects and ignores small pulses. FIGURE 4-2: In PIC18F2450/4450 devices, the MCLR input can be disabled with the MCLRE Configuration bit. When MCLR is disabled, the pin becomes a digital input. See Section 9.5 “PORTE, TRISE and LATE Registers” for more information. 4.3 D To take advantage of the POR circuitry, tie the MCLR pin through a resistor (1 kΩ to 10 kΩ) to VDD. This will eliminate external RC components usually needed to create a Power-on Reset delay. A minimum rise rate for VDD is specified (parameter D004, Section269 “DC Characteristics”). For a slow rise time, see Figure 4-2. R R1 C MCLR PIC18FXXXX Note 1: External Power-on Reset circuit is required only if the VDD power-up slope is too slow. The diode D helps discharge the capacitor quickly when VDD powers down. 2: R < 40 kΩ is recommended to make sure that the voltage drop across R does not violate the device’s electrical specification. 3: R1 ≥ 1 kΩ will limit any current flowing into MCLR from external capacitor C, in the event of MCLR/VPP pin breakdown, due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS). Power-on Reset (POR) A Power-on Reset pulse is generated on-chip whenever VDD rises above a certain threshold. This allows the device to start in the initialized state when VDD is adequate for operation. VDD VDD The MCLR pin is not driven low by any internal Resets, including the WDT. EXTERNAL POWER-ON RESET CIRCUIT (FOR SLOW VDD POWER-UP) When the device starts normal operation (i.e., exits the Reset condition), device operating parameters (voltage, frequency, temperature, etc.) must be met to ensure operation. If these conditions are not met, the device must be held in Reset until the operating conditions are met. POR events are captured by the POR bit (RCON<1>). The state of the bit is set to ‘0’ whenever a Power-on Reset occurs; it does not change for any other Reset event. POR is not reset to ‘1’ by any hardware event. To capture multiple events, the user manually resets the bit to ‘1’ in software following any Power-on Reset. © 2008 Microchip Technology Inc. DS39760D-page 43 PIC18F2450/4450 4.4 Brown-out Reset (BOR) PIC18F2450/4450 devices implement a BOR circuit that provides the user with a number of configuration and power-saving options. The BOR is controlled by the BORV1:BORV0 and BOREN1:BOREN0 Configuration bits. There are a total of four BOR configurations which are summarized in Table 4-1. The BOR threshold is set by the BORV1:BORV0 bits. If BOR is enabled (any values of BOREN1:BOREN0 except ‘00’), any drop of VDD below VBOR (parameter D005, Section 269 “DC Characteristics: Supply Voltage”) for greater than TBOR (parameter 35, Table 21-10) will reset the device. A Reset may or may not occur if VDD falls below VBOR for less than TBOR. The chip will remain in Brown-out Reset until VDD rises above VBOR. If the Power-up Timer is enabled, it will be invoked after VDD rises above VBOR; it then will keep the chip in Reset for an additional time delay, TPWRT (parameter 33, Table 21-10). If VDD drops below VBOR while the Power-up Timer is running, the chip will go back into a Brown-out Reset and the Power-up Timer will be initialized. Once VDD rises above VBOR, the Power-up Timer will execute the additional time delay. BOR and the Power-on Timer (PWRT) are independently configured. Enabling BOR Reset does not automatically enable the PWRT. 4.4.1 SOFTWARE ENABLED BOR When BOREN1:BOREN0 = 01, the BOR can be enabled or disabled by the user in software. This is done with the control bit, SBOREN (RCON<6>). Setting SBOREN enables the BOR to function as previously described. Clearing SBOREN disables the BOR entirely. The SBOREN bit operates only in this mode; otherwise, it is read as ‘0’. TABLE 4-1: Placing the BOR under software control gives the user the additional flexibility of tailoring the application to its environment without having to reprogram the device to change BOR configuration. It also allows the user to tailor device power consumption in software by eliminating the incremental current that the BOR consumes. While the BOR current is typically very small, it may have some impact in low-power applications. Note: 4.4.2 Even when BOR is under software control, the BOR Reset voltage level is still set by the BORV1:BORV0 Configuration bits. It cannot be changed in software. DETECTING BOR When Brown-out Reset is enabled, the BOR bit always resets to ‘0’ on any Brown-out Reset or Power-on Reset event. This makes it difficult to determine if a Brown-out Reset event has occurred just by reading the state of BOR alone. A more reliable method is to simultaneously check the state of both POR and BOR. This assumes that the POR bit is reset to ‘1’ in software immediately after any Power-on Reset event. IF BOR is ‘0’ while POR is ‘1’, it can be reliably assumed that a Brown-out Reset event has occurred. 4.4.3 DISABLING BOR IN SLEEP MODE When BOREN1:BOREN0 = 10, the BOR remains under hardware control and operates as previously described. Whenever the device enters Sleep mode, however, the BOR is automatically disabled. When the device returns to any other operating mode, BOR is automatically re-enabled. This mode allows for applications to recover from brown-out situations, while actively executing code, when the device requires BOR protection the most. At the same time, it saves additional power in Sleep mode by eliminating the small incremental BOR current. BOR CONFIGURATIONS BOR Configuration BOREN1 BOREN0 Status of SBOREN (RCON<6>) 0 0 Unavailable 0 1 Available 1 0 Unavailable BOR enabled in hardware in Run and Idle modes, disabled during Sleep mode. 1 1 Unavailable BOR enabled in hardware; must be disabled by reprogramming the Configuration bits. DS39760D-page 44 BOR Operation BOR disabled; must be enabled by reprogramming the Configuration bits. BOR enabled in software; operation controlled by SBOREN. © 2008 Microchip Technology Inc. PIC18F2450/4450 4.5 Device Reset Timers 4.5.3 PIC18F2450/4450 devices incorporate three separate on-chip timers that help regulate the Power-on Reset process. Their main function is to ensure that the device clock is stable before code is executed. These timers are: • Power-up Timer (PWRT) • Oscillator Start-up Timer (OST) • PLL Lock Time-out 4.5.1 With the PLL enabled in its PLL mode, the time-out sequence following a Power-on Reset is slightly different from other oscillator modes. A separate timer is used to provide a fixed time-out that is sufficient for the PLL to lock to the main oscillator frequency. This PLL lock time-out (TPLL) is typically 2 ms and follows the oscillator start-up time-out. 4.5.4 POWER-UP TIMER (PWRT) The Power-up Timer (PWRT) of the PIC18F2450/4450 devices is an 11-bit counter which uses the INTRC source as the clock input. This yields an approximate time interval of 2048 x 32 μs = 65.6 ms. While the PWRT is counting, the device is held in Reset. The power-up time delay depends on the INTRC clock and will vary from chip to chip due to temperature and process variation. See DC parameter 33 (Table 21-10) for details. The PWRT is enabled by clearing the PWRTEN Configuration bit. 4.5.2 PLL LOCK TIME-OUT OSCILLATOR START-UP TIMER (OST) The Oscillator Start-up Timer (OST) provides a 1024 oscillator cycle (from OSC1 input) delay after the PWRT delay is over (parameter 33, Table 21-10). This ensures that the crystal oscillator or resonator has started and stabilized. TIME-OUT SEQUENCE On power-up, the time-out sequence is as follows: 1. 2. After the POR condition has cleared, PWRT time-out is invoked (if enabled). Then, the OST is activated. The total time-out will vary based on oscillator configuration and the status of the PWRT. Figure 4-3, Figure 4-4, Figure 4-5, Figure 4-6 and Figure 4-7 all depict time-out sequences on power-up, with the Power-up Timer enabled and the device operating in HS Oscillator mode. Figure 4-3 through Figure 4-6 also apply to devices operating in XT mode. For devices in RC mode and with the PWRT disabled, on the other hand, there will be no time-out at all. Since the time-outs occur from the POR pulse, if MCLR is kept low long enough, all time-outs will expire. Bringing MCLR high will begin execution immediately (Figure 4-5). This is useful for testing purposes or to synchronize more than one PIC18FXXXX device operating in parallel. The OST time-out is invoked only for XT, HS and HSPLL modes and only on Power-on Reset or on exit from most power-managed modes. TABLE 4-2: TIME-OUT IN VARIOUS SITUATIONS Power-up(2) and Brown-out Oscillator Configuration PWRTEN = 0 1024 TOSC 1024 TOSC 66 ms(1) + 1024 TOSC + 2 ms(2) 1024 TOSC + 2 ms(2) 1024 TOSC + 2 ms(2) 66 ms(1) — — 66 ms(1) + 2 ms(2) 2 ms(2) 2 ms(2) EC, ECIO ECPLL, ECPIO 66 ms(1) INTIO, INTCKO INTHS, INTXT Note 1: 2: Exit from Power-Managed Mode 66 ms(1) + 1024 TOSC HS, XT HSPLL, XTPLL PWRTEN = 1 66 ms(1) + 1024 TOSC — — 1024 TOSC 1024 TOSC 66 ms (65.5 ms) is the nominal Power-up Timer (PWRT) delay. 2 ms is the nominal time required for the PLL to lock. © 2008 Microchip Technology Inc. DS39760D-page 45 PIC18F2450/4450 FIGURE 4-3: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD, VDD RISE < TPWRT) VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1 FIGURE 4-4: VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2 FIGURE 4-5: VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET DS39760D-page 46 © 2008 Microchip Technology Inc. PIC18F2450/4450 FIGURE 4-6: SLOW RISE TIME (MCLR TIED TO VDD, VDD RISE > TPWRT) 5V VDD 1V 0V MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET TIME-OUT SEQUENCE ON POR w/PLL ENABLED (MCLR TIED TO VDD) FIGURE 4-7: VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT OST TIME-OUT TOST TPLL PLL TIME-OUT INTERNAL RESET Note: TOST = 1024 clock cycles. TPLL ≈ 2 ms max. First three stages of the Power-up Timer. © 2008 Microchip Technology Inc. DS39760D-page 47 PIC18F2450/4450 4.6 Reset State of Registers POR and BOR, are set or cleared differently in different Reset situations as indicated in Table 4-3. These bits are used in software to determine the nature of the Reset. Most registers are unaffected by a Reset. Their status is unknown on POR and unchanged by all other Resets. The other registers are forced to a “Reset state” depending on the type of Reset that occurred. Table 4-4 describes the Reset states for all of the Special Function Registers. These are categorized by Power-on and Brown-out Resets, Master Clear and WDT Resets and WDT wake-ups. Most registers are not affected by a WDT wake-up, since this is viewed as the resumption of normal operation. Status bits from the RCON register, RI, TO, PD, TABLE 4-3: STATUS BITS, THEIR SIGNIFICANCE AND THE INITIALIZATION CONDITION FOR RCON REGISTER Condition Program Counter RCON Register SBOREN RI TO PD STKPTR Register POR BOR STKFUL STKUNF Power-on Reset 0000h 1 1 1 1 0 0 0 0 RESET instruction 0000h u(2) 0 u u u u u u Brown-out Reset 0000h u (2) 1 1 1 u 0 u u MCLR Reset during power-managed Run modes 0000h u(2) u 1 u u u u u MCLR Reset during power-managed Idle modes and Sleep mode 0000h u(2) u 1 0 u u u u WDT time-out during full-power or power-managed Run modes 0000h u(2) u 0 u u u u u MCLR Reset during full-power execution 0000h u(2) u u u u u u u Stack Full Reset (STVREN = 1) 0000h u(2) u u u u u 1 u Stack Underflow Reset (STVREN = 1) 0000h u(2) u u u u u u 1 Stack Underflow Error (not an actual Reset, STVREN = 0) 0000h u(2) u u u u u u 1 WDT time-out during power-managed Idle or Sleep modes PC + 2 u(2) u 0 0 u u u u PC + 2(1) u(2) u u 0 u u u u Interrupt exit from power-managed modes Legend: u = unchanged Note 1: When the wake-up is due to an interrupt and the GIEH or GIEL bit is set, the PC is loaded with the interrupt vector (008h or 0018h). 2: Reset state is ‘1’ for POR and unchanged for all other Resets when software BOR is enabled (BOREN1:BOREN0 Configuration bits = 01 and SBOREN = 1); otherwise, the Reset state is ‘0’. DS39760D-page 48 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 4-4: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS Applicable Devices Power-on Reset, Brown-out Reset MCLR Resets, WDT Reset, RESET Instruction, Stack Resets Wake-up via WDT or Interrupt TOSU 2450 4450 ---0 0000 ---0 0000 ---0 uuuu(1) TOSH 2450 4450 0000 0000 0000 0000 uuuu uuuu(1) TOSL 2450 4450 0000 0000 0000 0000 uuuu uuuu(1) STKPTR 2450 4450 00-0 0000 uu-0 0000 uu-u uuuu(1) PCLATU 2450 4450 ---0 0000 ---0 0000 ---u uuuu PCLATH 2450 4450 0000 0000 0000 0000 uuuu uuuu PCL 2450 4450 0000 0000 0000 0000 PC + 2(3) TBLPTRU 2450 4450 --00 0000 --00 0000 --uu uuuu TBLPTRH 2450 4450 0000 0000 0000 0000 uuuu uuuu TBLPTRL 2450 4450 0000 0000 0000 0000 uuuu uuuu TABLAT 2450 4450 0000 0000 0000 0000 uuuu uuuu PRODH 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu PRODL 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu INTCON 2450 4450 0000 000x 0000 000u uuuu uuuu(2) INTCON2 2450 4450 1111 -1-1 1111 -1-1 uuuu -u-u(2) INTCON3 2450 4450 11-0 0-00 11-0 0-00 uu-u u-uu(2) INDF0 2450 4450 N/A N/A N/A POSTINC0 2450 4450 N/A N/A N/A POSTDEC0 2450 4450 N/A N/A N/A PREINC0 2450 4450 N/A N/A N/A PLUSW0 2450 4450 N/A N/A N/A FSR0H 2450 4450 ---- 0000 ---- 0000 ---- uuuu FSR0L 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu WREG 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu INDF1 2450 4450 N/A N/A N/A POSTINC1 2450 4450 N/A N/A N/A POSTDEC1 2450 4450 N/A N/A N/A PREINC1 2450 4450 N/A N/A N/A PLUSW1 2450 4450 N/A N/A N/A FSR1H 2450 4450 ---- 0000 ---- 0000 ---- uuuu FSR1L 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu BSR 2450 4450 ---- 0000 ---- 0000 ---- uuuu Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition. Shaded cells indicate conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 3: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 4: See Table 4-3 for Reset value for specific condition. 5: PORTA<6>, LATA<6> and TRISA<6> are enabled depending on the oscillator mode selected. When not enabled as PORTA pins, they are disabled and read ‘0’. © 2008 Microchip Technology Inc. DS39760D-page 49 PIC18F2450/4450 TABLE 4-4: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Applicable Devices Power-on Reset, Brown-out Reset MCLR Resets, WDT Reset, RESET Instruction, Stack Resets Wake-up via WDT or Interrupt INDF2 2450 4450 N/A N/A N/A POSTINC2 2450 4450 N/A N/A N/A POSTDEC2 2450 4450 N/A N/A N/A PREINC2 2450 4450 N/A N/A N/A PLUSW2 2450 4450 N/A N/A N/A FSR2H 2450 4450 ---- 0000 ---- 0000 ---- uuuu FSR2L 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu STATUS 2450 4450 ---x xxxx ---u uuuu ---u uuuu TMR0H 2450 4450 0000 0000 0000 0000 uuuu uuuu TMR0L 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu T0CON 2450 4450 1111 1111 1111 1111 uuuu uuuu OSCCON 2450 4450 0--- q-00 0--- 0-q0 u--- u-qu u-uu uuuu HLVDCON 2450 4450 0-00 0101 0-00 0101 WDTCON 2450 4450 ---- ---0 ---- ---0 ---- ---u RCON 2450 4450 0q-1 11q0 0q-q qquu uq-u qquu TMR1H 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu TMR1L 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu T1CON 2450 4450 0000 0000 u0uu uuuu uuuu uuuu TMR2 2450 4450 0000 0000 0000 0000 uuuu uuuu PR2 2450 4450 1111 1111 1111 1111 1111 1111 T2CON 2450 4450 -000 0000 -000 0000 -uuu uuuu ADRESH 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu (4) ADRESL 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu ADCON0 2450 4450 --00 0000 --00 0000 --uu uuuu ADCON1 2450 4450 --00 qqqq --00 qqqq --uu uuuu ADCON2 2450 4450 0-00 0000 0-00 0000 u-uu uuuu CCPR1H 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu CCPR1L 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu CCP1CON 2450 4450 --00 0000 --00 0000 --uu uuuu BAUDCON 2450 4450 01-0 0-00 01-0 0-00 uu-u u-uu SPBRG 2450 4450 0000 0000 0000 0000 uuuu uuuu RCREG 2450 4450 0000 0000 0000 0000 uuuu uuuu Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition. Shaded cells indicate conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 3: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 4: See Table 4-3 for Reset value for specific condition. 5: PORTA<6>, LATA<6> and TRISA<6> are enabled depending on the oscillator mode selected. When not enabled as PORTA pins, they are disabled and read ‘0’. DS39760D-page 50 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 4-4: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Applicable Devices Power-on Reset, Brown-out Reset MCLR Resets, WDT Reset, RESET Instruction, Stack Resets Wake-up via WDT or Interrupt TXREG 2450 4450 0000 0000 0000 0000 uuuu uuuu TXSTA 2450 4450 0000 0010 0000 0010 uuuu uuuu RCSTA 2450 4450 0000 000x 0000 000x uuuu uuuu EECON2 2450 4450 0000 0000 0000 0000 0000 0000 EECON1 2450 4450 -x-0 x00- -u-0 u00- -u-0 u00- IPIR2 2450 4450 1-1- -1-- 1-1- -1-- u-u- -u-- PIR2 2450 4450 0-0- -0-- 0-0- -0-- u-u- -u--(2) PIE2 2450 4450 0-0- -0-- 0-0- -0-- u-u- -u-- IPR1 2450 4450 -111 -111 -111 -111 -uuu -uuu PIR1 2450 4450 -000 -000 -000 -000 -uuu -uuu(2) PIE1 2450 4450 -000 -000 -000 -000 -uuu -uuu TRISE 2450 4450 ---- -111 ---- -111 ---- -uuu TRISD 2450 4450 1111 1111 1111 1111 uuuu uuuu TRISC 2450 4450 11-- -111 11-- -111 uu-- -uuu TRISB 2450 4450 1111 1111 1111 1111 uuuu uuuu TRISA(5) 2450 4450 -111 1111(5) -111 1111(5) -uuu uuuu(5) LATE 2450 4450 ---- -xxx ---- -uuu ---- -uuu LATD 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu LATC 2450 4450 xx-- -xxx uu-- -uuu uu-- -uuu LATB 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu (5) LATA 2450 4450 -xxx xxxx(5) -uuu uuuu(5) -uuu uuuu(5) PORTE 2450 4450 ---- x000 ---- x000 ---- uuuu PORTD 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu PORTC 2450 4450 xxxx -xxx uuuu -uuu uuuu -uuu PORTB 2450 4450 xxxx xxxx uuuu uuuu uuuu uuuu PORTA(5) 2450 4450 -x0x 0000(5) -u0u 0000(5) -uuu uuuu(5) UEP15 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP14 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP13 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP12 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP11 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP10 2450 4450 ---0 0000 ---0 0000 ---u uuuu Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition. Shaded cells indicate conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 3: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 4: See Table 4-3 for Reset value for specific condition. 5: PORTA<6>, LATA<6> and TRISA<6> are enabled depending on the oscillator mode selected. When not enabled as PORTA pins, they are disabled and read ‘0’. © 2008 Microchip Technology Inc. DS39760D-page 51 PIC18F2450/4450 TABLE 4-4: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Applicable Devices Power-on Reset, Brown-out Reset MCLR Resets, WDT Reset, RESET Instruction, Stack Resets Wake-up via WDT or Interrupt UEP9 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP8 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP7 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP6 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP5 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP4 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP3 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP2 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP1 2450 4450 ---0 0000 ---0 0000 ---u uuuu UEP0 2450 4450 ---0 0000 ---0 0000 ---u uuuu UCFG 2450 4450 00-0 0000 00-0 0000 uu-u uuuu UADDR 2450 4450 -000 0000 -000 0000 -uuu uuuu UCON 2450 4450 -0x0 000- -0x0 000- -uuu uuu- USTAT 2450 4450 -xxx xxx- -xxx xxx- -uuu uuu- UEIE 2450 4450 0--0 0000 0--0 0000 u--u uuuu UEIR 2450 4450 0--0 0000 0--0 0000 u--u uuuu UIE 2450 4450 -000 0000 -000 0000 -uuu uuuu UIR 2450 4450 -000 0000 -000 0000 -uuu uuuu UFRMH 2450 4450 ---- -xxx ---- -xxx ---- -uuu UFRML 2450 4450 xxxx xxxx xxxx xxxx uuuu uuuu Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition. Shaded cells indicate conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 3: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 4: See Table 4-3 for Reset value for specific condition. 5: PORTA<6>, LATA<6> and TRISA<6> are enabled depending on the oscillator mode selected. When not enabled as PORTA pins, they are disabled and read ‘0’. DS39760D-page 52 © 2008 Microchip Technology Inc. PIC18F2450/4450 5.0 MEMORY ORGANIZATION 5.1 Program Memory Organization PIC18 microcontrollers implement a 21-bit program counter which is capable of addressing a 2-Mbyte program memory space. Accessing a location between the upper boundary of the physically implemented memory and the 2-Mbyte address will return all ‘0’s (a NOP instruction). There are two types of memory in PIC18F2450/4450 microcontroller devices: • Program Memory • Data RAM As Harvard architecture devices, the data and program memories use separate busses; this allows for concurrent access of the two memory spaces. The PIC18F2450 and PIC18F4450 each have 16 Kbytes of Flash memory and can store up to 8192 single-word instructions. Additional detailed information on the operation of the Flash program memory is provided in Section 6.0 “Flash Program Memory”. PIC18 devices have two interrupt vectors. The Reset vector address is at 0000h and the interrupt vector addresses are at 0008h and 0018h. The program memory maps for PIC18F2450 and PIC18F4450 devices are shown in Figure 5-1. FIGURE 5-1: PROGRAM MEMORY MAP AND STACK FOR PIC18F2450/4450 DEVICES PIC18F2450/4450 PC<20:0> CALL, RCALL, RETURN, RETFIE, RETLW, CALLW, ADDULNK, SUBULNK 21 Stack Level 1 • • • Stack Level 31 Reset Vector 0000h High-Priority Interrupt Vector 0008h Low-Priority Interrupt Vector 0018h 3FFFh 4000h Read ‘0’ User Memory Space On-Chip Program Memory 1FFFFFh 200000h © 2008 Microchip Technology Inc. DS39760D-page 53 PIC18F2450/4450 5.1.1 PROGRAM COUNTER The Program Counter (PC) specifies the address of the instruction to fetch for execution. The PC is 21 bits wide and is contained in three separate 8-bit registers. The low byte, known as the PCL register, is both readable and writable. The high byte, or PCH register, contains the PC<15:8> bits; it is not directly readable or writable. Updates to the PCH register are performed through the PCLATH register. The upper byte is called PCU. This register contains the PC<20:16> bits; it is also not directly readable or writable. Updates to the PCU register are performed through the PCLATU register. The contents of PCLATH and PCLATU are transferred to the program counter by any operation that writes PCL. Similarly, the upper two bytes of the program counter are transferred to PCLATH and PCLATU by an operation that reads PCL. This is useful for computed offsets to the PC (see Section 5.1.4.1 “Computed GOTO”). The PC addresses bytes in the program memory. To prevent the PC from becoming misaligned with word instructions, the Least Significant bit of PCL is fixed to a value of ‘0’. The PC increments by 2 to address sequential instructions in the program memory. The CALL, RCALL and GOTO program branch instructions write to the program counter directly. For these instructions, the contents of PCLATH and PCLATU are not transferred to the program counter. 5.1.2 RETURN ADDRESS STACK The return address stack allows any combination of up to 31 program calls and interrupts to occur. The PC is pushed onto the stack when a CALL or RCALL instruction is executed or an interrupt is Acknowledged. The PC value is pulled off the stack on a RETURN, RETLW or a RETFIE instruction. PCLATU and PCLATH are not affected by any of the RETURN or CALL instructions. FIGURE 5-2: The stack operates as a 31-word by 21-bit RAM and a 5-bit Stack Pointer, STKPTR. The stack space is not part of either program or data space. The Stack Pointer is readable and writable and the address on the top of the stack is readable and writable through the Top-ofStack Special Function Registers. Data can also be pushed to, or popped from the stack, using these registers. A CALL type instruction causes a push onto the stack. The Stack Pointer is first incremented and the location pointed to by the Stack Pointer is written with the contents of the PC (already pointing to the instruction following the CALL). A RETURN type instruction causes a pop from the stack. The contents of the location pointed to by the STKPTR are transferred to the PC and then the Stack Pointer is decremented. The Stack Pointer is initialized to ‘00000’ after all Resets. There is no RAM associated with the location corresponding to a Stack Pointer value of ‘00000’; this is only a Reset value. Status bits indicate if the stack is full, has overflowed or has underflowed. 5.1.2.1 Top-of-Stack Access Only the top of the return address stack (TOS) is readable and writable. A set of three registers, TOSU:TOSH:TOSL, hold the contents of the stack location pointed to by the STKPTR register (Figure 5-2). This allows users to implement a software stack if necessary. After a CALL, RCALL or interrupt, the software can read the pushed value by reading the TOSU:TOSH:TOSL registers. These values can be placed on a user-defined software stack. At return time, the software can return these values to TOSU:TOSH:TOSL and do a return. The user must disable the global interrupt enable bits while accessing the stack to prevent inadvertent stack corruption. RETURN ADDRESS STACK AND ASSOCIATED REGISTERS Return Address Stack<20:0> 11111 11110 11101 Top-of-Stack Registers TOSU 00h TOSH 1Ah DS39760D-page 54 STKPTR<4:0> 00010 TOSL 34h Top-of-Stack Stack Pointer 001A34h 000D58h 00011 00010 00001 00000 © 2008 Microchip Technology Inc. PIC18F2450/4450 5.1.2.2 Return Stack Pointer (STKPTR) When the stack has been popped enough times to unload the stack, the next pop will return a value of zero to the PC and sets the STKUNF bit, while the Stack Pointer remains at zero. The STKUNF bit will remain set until cleared by software or until a POR occurs. The STKPTR register (Register 5-1) contains the Stack Pointer value, the STKFUL (Stack Full) status bit and the STKUNF (Stack Underflow) status bit. The value of the Stack Pointer can be 0 through 31. The Stack Pointer increments before values are pushed onto the stack and decrements after values are popped off the stack. On Reset, the Stack Pointer value will be zero. The user may read and write the Stack Pointer value. This feature can be used by a Real-Time Operating System (RTOS) for return stack maintenance. Note: After the PC is pushed onto the stack 31 times (without popping any values off the stack), the STKFUL bit is set. The STKFUL bit is cleared by software or by a POR. 5.1.2.3 PUSH and POP Instructions Since the Top-of-Stack is readable and writable, the ability to push values onto the stack and pull values off the stack, without disturbing normal program execution, is a desirable feature. The PIC18 instruction set includes two instructions, PUSH and POP, that permit the TOS to be manipulated under software control. TOSU, TOSH and TOSL can be modified to place data or a return address on the stack. The action that takes place when the stack becomes full depends on the state of the STVREN (Stack Overflow Reset Enable) Configuration bit. (Refer to Section 18.1 “Configuration Bits” for a description of the device Configuration bits.) If STVREN is set (default), the 31st push will push the (PC + 2) value onto the stack, set the STKFUL bit and reset the device. The STKFUL bit will remain set and the Stack Pointer will be set to zero. The PUSH instruction places the current PC value onto the stack. This increments the Stack Pointer and loads the current PC value onto the stack. If STVREN is cleared, the STKFUL bit will be set on the 31st push and the Stack Pointer will increment to 31. Any additional pushes will not overwrite the 31st push and the STKPTR will remain at 31. REGISTER 5-1: Returning a value of zero to the PC on an underflow has the effect of vectoring the program to the Reset vector, where the stack conditions can be verified and appropriate actions can be taken. This is not the same as a Reset, as the contents of the SFRs are not affected. The POP instruction discards the current TOS by decrementing the Stack Pointer. The previous value pushed onto the stack then becomes the TOS value. STKPTR: STACK POINTER REGISTER R/C-0 R/C-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 STKFUL(1) STKUNF(1) — SP4 SP3 SP2 SP1 SP0 bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 STKFUL: Stack Full Flag bit(1) 1 = Stack became full or overflowed 0 = Stack has not become full or overflowed bit 6 STKUNF: Stack Underflow Flag bit(1) 1 = Stack underflow occurred 0 = Stack underflow did not occur bit 5 Unimplemented: Read as ‘0’ bit 4-0 SP4:SP0: Stack Pointer Location bits Note 1: x = Bit is unknown Bit 7 and bit 6 are cleared by user software or by a POR. © 2008 Microchip Technology Inc. DS39760D-page 55 PIC18F2450/4450 5.1.2.4 Stack Full and Underflow Resets Device Resets on stack overflow and stack underflow conditions are enabled by setting the STVREN bit in Configuration Register 4L. When STVREN is set, a full or underflow condition will set the appropriate STKFUL or STKUNF bit and then cause a device Reset. When STVREN is cleared, a full or underflow condition will set the appropriate STKFUL or STKUNF bit but not cause a device Reset. The STKFUL or STKUNF bits are cleared by user software or a Power-on Reset. 5.1.3 FAST REGISTER STACK A Fast Register Stack is provided for the STATUS, WREG and BSR registers to provide a “fast return” option for interrupts. Each stack is only one level deep and is neither readable nor writable. It is loaded with the current value of the corresponding register when the processor vectors for an interrupt. All interrupt sources will push values into the stack registers. The values in the registers are then loaded back into their associated registers if the RETFIE, FAST instruction is used to return from the interrupt. 5.1.4 LOOK-UP TABLES IN PROGRAM MEMORY There may be programming situations that require the creation of data structures, or look-up tables, in program memory. For PIC18 devices, look-up tables can be implemented in two ways: • Computed GOTO • Table Reads 5.1.4.1 Computed GOTO A computed GOTO is accomplished by adding an offset to the program counter. An example is shown in Example 5-2. A look-up table can be formed with an ADDWF PCL instruction and a group of RETLW nn instructions. The W register is loaded with an offset into the table before executing a call to that table. The first instruction of the called routine is the ADDWF PCL instruction. The next instruction executed will be one of the RETLW nn instructions that returns the value ‘nn’ to the calling function. If both low and high-priority interrupts are enabled, the stack registers cannot be used reliably to return from low-priority interrupts. If a high-priority interrupt occurs while servicing a low-priority interrupt, the stack register values stored by the low-priority interrupt will be overwritten. In these cases, users must save the key registers in software during a low-priority interrupt. The offset value (in WREG) specifies the number of bytes that the program counter should advance and should be multiples of 2 (LSb = 0). If interrupt priority is not used, all interrupts may use the Fast Register Stack for returns from interrupt. If no interrupts are used, the Fast Register Stack can be used to restore the STATUS, WREG and BSR registers at the end of a subroutine call. To use the Fast Register Stack for a subroutine call, a CALL label, FAST instruction must be executed to save the STATUS, WREG and BSR registers to the Fast Register Stack. A RETURN, FAST instruction is then executed to restore these registers from the Fast Register Stack. EXAMPLE 5-2: Example 5-1 shows a source code example that uses the Fast Register Stack during a subroutine call and return. EXAMPLE 5-1: CALL FAST REGISTER STACK CODE EXAMPLE SUB1, FAST • • SUB1 • • RETURN, FAST DS39760D-page 56 ;STATUS, WREG, BSR ;SAVED IN FAST REGISTER ;STACK ;RESTORE VALUES SAVED ;IN FAST REGISTER STACK In this method, only one data byte may be stored in each instruction location and room on the return address stack is required. ORG TABLE 5.1.4.2 MOVF CALL nn00h ADDWF RETLW RETLW RETLW . . . COMPUTED GOTO USING AN OFFSET VALUE OFFSET, W TABLE PCL nnh nnh nnh Table Reads and Table Writes A better method of storing data in program memory allows two bytes of data to be stored in each instruction location. Look-up table data may be stored two bytes per program word by using table reads and writes. The Table Pointer (TBLPTR) register specifies the byte address and the Table Latch (TABLAT) register contains the data that is read from or written to program memory. Data is transferred to or from program memory one byte at a time. Table read and table write operations are discussed further in Section 6.1 “Table Reads and Table Writes”. © 2008 Microchip Technology Inc. PIC18F2450/4450 5.2 PIC18 Instruction Cycle 5.2.1 5.2.2 An “Instruction Cycle” consists of four Q cycles: Q1 through Q4. The instruction fetch and execute are pipelined in such a manner that a fetch takes one instruction cycle, while the decode and execute takes another instruction cycle. However, due to the pipelining, each instruction effectively executes in one cycle. If an instruction causes the program counter to change (e.g., GOTO), then two cycles are required to complete the instruction (Example 5-3). CLOCKING SCHEME The microcontroller clock input, whether from an internal or external source, is internally divided by four to generate four non-overlapping quadrature clocks (Q1, Q2, Q3 and Q4). Internally, the program counter is incremented on every Q1; the instruction is fetched from the program memory and latched into the Instruction Register (IR) during Q4. The instruction is decoded and executed during the following Q1 through Q4. The clocks and instruction execution flow are shown in Figure 5-3. FIGURE 5-3: INSTRUCTION FLOW/PIPELINING A fetch cycle begins with the Program Counter (PC) incrementing in Q1. In the execution cycle, the fetched instruction is latched into the Instruction Register (IR) in cycle Q1. This instruction is then decoded and executed during the Q2, Q3 and Q4 cycles. Data memory is read during Q2 (operand read) and written during Q4 (destination write). CLOCK/INSTRUCTION CYCLE Q1 Q2 Q3 Q4 Q2 Q1 Q3 Q4 Q2 Q1 Q3 Q4 OSC1 Q1 Q2 Internal Phase Clock Q3 Q4 PC PC PC + 2 PC + 4 OSC2/CLKO (RC mode) Execute INST (PC – 2) Fetch INST (PC) EXAMPLE 5-3: TCY0 TCY1 Fetch 1 Execute 1 2. MOVWF PORTB 4. BSF SUB_1 PORTA, BIT3 (Forced NOP) 5. Instruction @ address SUB_1 Note: Execute INST (PC + 2) Fetch INST (PC + 4) INSTRUCTION PIPELINE FLOW 1. MOVLW 55h 3. BRA Execute INST (PC) Fetch INST (PC + 2) Fetch 2 TCY2 TCY3 TCY4 TCY5 Execute 2 Fetch 3 Execute 3 Fetch 4 Flush (NOP) Fetch SUB_1 Execute SUB_1 All instructions are single cycle, except for any program branches. These take two cycles since the fetch instruction is “flushed” from the pipeline while the new instruction is being fetched and then executed. © 2008 Microchip Technology Inc. DS39760D-page 57 PIC18F2450/4450 5.2.3 INSTRUCTIONS IN PROGRAM MEMORY The program memory is addressed in bytes. Instructions are stored as two bytes or four bytes in program memory. The Least Significant Byte of an instruction word is always stored in a program memory location with an even address (LSb = 0). To maintain alignment with instruction boundaries, the PC increments in steps of 2 and the LSb will always read ‘0’ (see Section 5.1.1 “Program Counter”). Figure 5-4 shows an example of how instruction words are stored in the program memory. FIGURE 5-4: INSTRUCTIONS IN PROGRAM MEMORY Program Memory Byte Locations → 5.2.4 Instruction 1: Instruction 2: MOVLW GOTO 055h 0006h Instruction 3: MOVFF 123h, 456h TWO-WORD INSTRUCTIONS The standard PIC18 instruction set has four two-word instructions: CALL, MOVFF, GOTO and LSFR. In all cases, the second word of the instructions always has ‘1111’ as its four Most Significant bits; the other 12 bits are literal data, usually a data memory address. The use of ‘1111’ in the 4 MSbs of an instruction specifies a special form of NOP. If the instruction is executed in proper sequence, immediately after the first word, the data in the second word is accessed and EXAMPLE 5-4: The CALL and GOTO instructions have the absolute program memory address embedded into the instruction. Since instructions are always stored on word boundaries, the data contained in the instruction is a word address. The word address is written to PC<20:1>, which accesses the desired byte address in program memory. Instruction #2 in Figure 5-4 shows how the instruction, GOTO 0006h, is encoded in the program memory. Program branch instructions, which encode a relative address offset, operate in the same manner. The offset value stored in a branch instruction represents the number of single-word instructions that the PC will be offset by. Section 19.0 “Instruction Set Summary” provides further details of the instruction set. LSB = 1 LSB = 0 0Fh EFh F0h C1h F4h 55h 03h 00h 23h 56h Word Address ↓ 000000h 000002h 000004h 000006h 000008h 00000Ah 00000Ch 00000Eh 000010h 000012h 000014h used by the instruction sequence. If the first word is skipped for some reason and the second word is executed by itself, a NOP is executed instead. This is necessary for cases when the two-word instruction is preceded by a conditional instruction that changes the PC. Example 5-4 shows how this works. Note: See Section 5.5 “Program Memory and the Extended Instruction Set” for information on two-word instruction in the extended instruction set. TWO-WORD INSTRUCTIONS CASE 1: Object Code Source Code 0110 0110 0000 0000 TSTFSZ REG1 1100 0001 0010 0011 MOVFF REG1, REG2 ; No, skip this word 1111 0100 0101 0110 0010 0100 0000 0000 ; is RAM location 0? ; Execute this word as a NOP ADDWF REG3 ; continue code CASE 2: Object Code Source Code 0110 0110 0000 0000 TSTFSZ REG1 1100 0001 0010 0011 MOVFF REG1, REG2 ; Yes, execute this word 1111 0100 0101 0110 0010 0100 0000 0000 DS39760D-page 58 ; is RAM location 0? ; 2nd word of instruction ADDWF REG3 ; continue code © 2008 Microchip Technology Inc. PIC18F2450/4450 5.3 Note: Data Memory Organization The operation of some aspects of data memory are changed when the PIC18 extended instruction set is enabled. See Section 5.6 “Data Memory and the Extended Instruction Set” for more information. The data memory in PIC18 devices is implemented as static RAM. Each register in the data memory has a 12-bit address, allowing up to 4096 bytes of data memory. The memory space is divided into as many as 16 banks that contain 256 bytes each. PIC18F2450/ 4450 devices implement three complete banks, for a total of 768 bytes. Figure 5-5 shows the data memory organization for the devices. The data memory contains Special Function Registers (SFRs) and General Purpose Registers (GPRs). The SFRs are used for control and status of the controller and peripheral functions, while GPRs are used for data storage and scratchpad operations in the user’s application. Any read of an unimplemented location will read as ‘0’s. The instruction set and architecture allow operations across all banks. The entire data memory may be accessed by Direct, Indirect or Indexed Addressing modes. Addressing modes are discussed later in this subsection. To ensure that commonly used registers (SFRs and select GPRs) can be accessed in a single cycle, PIC18 devices implement an Access Bank. This is a 256-byte memory space that provides fast access to SFRs and the lower portion of GPR Bank 0 without using the BSR. Section 5.3.3 “Access Bank” provides a detailed description of the Access RAM. 5.3.1 USB RAM Bank 4 of the data memory is actually mapped to special dual port RAM. When the USB module is disabled, the GPRs in these banks are used like any other GPR in the data memory space. When the USB module is enabled, the memory in this bank is allocated as buffer RAM for USB operation. This area is shared between the microcontroller core and the USB Serial Interface Engine (SIE) and is used to transfer data directly between the two. 5.3.2 BANK SELECT REGISTER (BSR) Large areas of data memory require an efficient addressing scheme to make rapid access to any address possible. Ideally, this means that an entire address does not need to be provided for each read or write operation. For PIC18 devices, this is accomplished with a RAM banking scheme. This divides the memory space into 16 contiguous banks of 256 bytes. Depending on the instruction, each location can be addressed directly by its full 12-bit address, or an 8-bit low-order address and a 4-bit Bank Pointer. Most instructions in the PIC18 instruction set make use of the Bank Pointer, known as the Bank Select Register (BSR). This SFR holds the 4 Most Significant bits of a location’s address; the instruction itself includes the 8 Least Significant bits. Only the four lower bits of the BSR are implemented (BSR3:BSR0). The upper four bits are unused; they will always read ‘0’ and cannot be written to. The BSR can be loaded directly by using the MOVLB instruction. The value of the BSR indicates the bank in data memory. The eight bits in the instruction show the location in the bank and can be thought of as an offset from the bank’s lower boundary. The relationship between the BSR’s value and the bank division in data memory is shown in Figure 5-6. Since up to 16 registers may share the same low-order address, the user must always be careful to ensure that the proper bank is selected before performing a data read or write. For example, writing what should be program data to an 8-bit address of F9h, while the BSR is 0Fh, will end up resetting the program counter. While any bank can be selected, only those banks that are actually implemented can be read or written to. Writes to unimplemented banks are ignored, while reads from unimplemented banks will return ‘0’s. Even so, the STATUS register will still be affected as if the operation was successful. The data memory map in Figure 5-6 indicates which banks are implemented. In the core PIC18 instruction set, only the MOVFF instruction fully specifies the 12-bit address of the source and target registers. This instruction ignores the BSR completely when it executes. All other instructions include only the low-order address as an operand and must use either the BSR or the Access Bank to locate their target registers. It is theoretically possible to use this area of USB RAM that is not allocated as USB buffers for normal scratchpad memory or other variable storage. In practice, the dynamic nature of buffer allocation makes this risky at best. Bank 4 is also used for USB buffer management when the module is enabled and should not be used for any other purposes during that time. Additional information on USB RAM and buffer operation is provided in Section 14.0 “Universal Serial Bus (USB)”. © 2008 Microchip Technology Inc. DS39760D-page 59 PIC18F2450/4450 FIGURE 5-5: DATA MEMORY MAP FOR PIC18F2450/4450 DEVICES BSR<3:0> = 0000 = 0001 = 0010 = 0011 = 0100 = 0101 When a = 0: Data Memory Map 00h Access RAM FFh 00h GPR Bank 0 GPR Bank 1 Bank 2 Bank 3 Bank 4 Bank 5 000h 05Fh 060h 0FFh 100h FFh 00h FFh 00h FFh 00h Unused Read as 00h Unused Read as 00h GPR(1) 1FFh 200h 2FFh 300h The BSR is ignored and the Access Bank is used. The first 96 bytes are general purpose RAM (from Bank 0). The remaining 160 bytes are Special Function Registers (from Bank 15). When a = 1: The BSR specifies the bank used by the instruction. 3FFh 400h 4FFh 800h FFh 00h Access Bank Access RAM Low 00h 5Fh Access RAM High 60h (SFRs) FFh to Unused Read as 00h = 1110 = 1111 Note 1: Bank 14 FFh 00h Unused FFh SFR Bank 15 EFFh F00h F5Fh F60h FFFh This bank also serve as RAM buffer for USB operation. See Section 5.3.1 “USB RAM” for more information. DS39760D-page 60 © 2008 Microchip Technology Inc. PIC18F2450/4450 FIGURE 5-6: USE OF THE BANK SELECT REGISTER (DIRECT ADDRESSING) BSR(1) 7 0 0 0 0 0 0 0 Bank Select(2) 1 1 000h Data Memory 00h Bank 0 100h Bank 1 200h Bank 2 300h FFh 00h From Opcode(2) 7 1 1 1 1 1 1 0 1 1 FFh 00h FFh 00h Bank 3 through Bank 13 E00h Bank 14 F00h FFFh Note 1: 2: 5.3.3 Bank 15 FFh 00h FFh 00h FFh The Access RAM bit of the instruction can be used to force an override of the selected bank (BSR<3:0>) to the registers of the Access Bank. The MOVFF instruction embeds the entire 12-bit address in the instruction. ACCESS BANK While the use of the BSR, with an embedded 8-bit address, allows users to address the entire range of data memory, it also means that the user must always ensure that the correct bank is selected. Otherwise, data may be read from or written to the wrong location. This can be disastrous if a GPR is the intended target of an operation but an SFR is written to instead. Verifying and/or changing the BSR for each read or write to data memory can become very inefficient. To streamline access for the most commonly used data memory locations, the data memory is configured with an Access Bank, which allows users to access a mapped block of memory without specifying a BSR. The Access Bank consists of the first 96 bytes of memory (00h-5Fh) in Bank 0 and the last 160 bytes of memory (60h-FFh) in Block 15. The lower half is known as the “Access RAM” and is composed of GPRs. The upper half is where the device’s SFRs are mapped. These two areas are mapped contiguously in the Access Bank and can be addressed in a linear fashion by an 8-bit address (Figure 5-5). The Access Bank is used by core PIC18 instructions that include the Access RAM bit (the ‘a’ parameter in the instruction). When ‘a’ is equal to ‘1’, the instruction uses the BSR and the 8-bit address included in the opcode for the data memory address. When ‘a’ is ‘0’, © 2008 Microchip Technology Inc. however, the instruction is forced to use the Access Bank address map; the current value of the BSR is ignored entirely. Using this “forced” addressing allows the instruction to operate on a data address in a single cycle without updating the BSR first. For 8-bit addresses of 60h and above, this means that users can evaluate and operate on SFRs more efficiently. The Access RAM below 60h is a good place for data values that the user might need to access rapidly, such as immediate computational results or common program variables. Access RAM also allows for faster and more code efficient context saving and switching of variables. The mapping of the Access Bank is slightly different when the extended instruction set is enabled (XINST Configuration bit = 1). This is discussed in more detail in Section 5.6.3 “Mapping the Access Bank in Indexed Literal Offset Mode”. 5.3.4 GENERAL PURPOSE REGISTER FILE PIC18 devices may have banked memory in the GPR area. This is data RAM which is available for use by all instructions. GPRs start at the bottom of Bank 0 (address 000h) and grow upwards towards the bottom of the SFR area. GPRs are not initialized by a Power-on Reset and are unchanged on all other Resets. DS39760D-page 61 PIC18F2450/4450 5.3.5 SPECIAL FUNCTION REGISTERS The Special Function Registers (SFRs) are registers used by the CPU and peripheral modules for controlling the desired operation of the device. These registers are implemented as static RAM in the data memory space. SFRs start at the top of data memory and extend downward to occupy the top segment of Bank 15, from F60h to FFFh. A list of these registers is given in Table 5-1 and Table 5-2. peripheral functions. The Reset and interrupt registers are described in their respective chapters, while the ALU’s STATUS register is described later in this section. Registers related to the operation of a peripheral feature are described in the chapter for that peripheral. The SFRs are typically distributed among the peripherals whose functions they control. Unused SFR locations are unimplemented and read as ‘0’s. The SFRs can be classified into two sets: those associated with the “core” device functionality (ALU, Resets and interrupts) and those related to the TABLE 5-1: Address SPECIAL FUNCTION REGISTER MAP FOR PIC18F2450/4450 DEVICES Name Address Name INDF2 (1) Address Name Address Name Address Name FFFh TOSU FDFh FBFh CCPR1H F9Fh IPR1 F7Fh UEP15 FFEh TOSH FDEh POSTINC2(1) FBEh CCPR1L F9Eh PIR1 F7Eh UEP14 FFDh TOSL FDDh POSTDEC2(1) FBDh CCP1CON F9Dh PIE1 F7Dh UEP13 FFCh STKPTR FDCh PREINC2(1) FBCh —(2) F9Ch —(2) F7Ch UEP12 FFBh PCLATU FDBh PLUSW2(1) FBBh —(2) F9Bh —(2) F7Bh UEP11 FFAh PCLATH FDAh FSR2H FBAh —(2) F9Ah —(2) F7Ah UEP10 FF9h PCL FD9h FSR2L FB9h —(2) F99h —(2) F79h UEP9 FF8h TBLPTRU FD8h STATUS FB8h BAUDCON F98h —(2) F78h UEP8 FF7h TBLPTRH FD7h TMR0H FB7h —(2) F97h —(2) F77h UEP7 FF6h TBLPTRL FD6h TMR0L FB6h —(2) F96h TRISE(3) F76h UEP6 (2) F95h (3) FF5h TABLAT FD5h T0CON FB5h — F75h UEP5 FF4h PRODH FD4h —(2) FB4h —(2) F94h TRISD TRISC F74h UEP4 FF3h PRODL FD3h OSCCON FB3h —(2) F93h TRISB F73h UEP3 FF2h INTCON FD2h HLVDCON FB2h —(2) F92h TRISA F72h UEP2 F71h UEP1 FF1h INTCON2 FD1h WDTCON FB1h —(2) F91h —(2) FF0h INTCON3 FD0h RCON FB0h SPBRGH F90h —(2) F70h UEP0 FEFh INDF0(1) FCFh TMR1H FAFh SPBRG F8Fh —(2) F6Fh UCFG FCEh TMR1L FAEh RCREG F8Eh —(2) F6Eh UADDR FEEh POSTINC0(1) FEDh POSTDEC0 (1) (3) FCDh T1CON FADh TXREG F8Dh LATE F6Dh UCON FECh PREINC0(1) FCCh TMR2 FACh TXSTA F8Ch LATD(3) F6Ch USTAT FEBh PLUSW0(1) FCBh PR2 FABh RCSTA F8Bh LATC F6Bh UEIE FEAh FSR0H FCAh T2CON FAAh —(2) F8Ah LATB F6Ah UEIR FE9h FSR0L FC9h —(2) FA9h —(2) F89h LATA F69h UIE FA8h —(2) F88h —(2) F68h UIR FE8h WREG FC8h —(2) FE7h INDF1(1) FC7h —(2) FA7h EECON2(1) F87h —(2) F67h UFRMH FC6h —(2) FA6h EECON1 F86h —(2) F66h UFRML FC5h (2) — (2) F85h (2) F65h —(2) FA4h — (2) F84h PORTE F64h —(2) F83h PORTD(3) F63h —(2) FE6h POSTINC1(1) FE5h POSTDEC1 (1) (1) ADRESH FA5h — FE4h PREINC1 FE3h PLUSW1(1) FC3h ADRESL FA3h —(2) FE2h FSR1H FC2h ADCON0 FA2h IPR2 F82h PORTC F62h —(2) FE1h FSR1L FC1h ADCON1 FA1h PIR2 F81h PORTB F61h —(2) FE0h BSR FC0h ADCON2 FA0h PIE2 F80h PORTA F60h —(2) Note 1: 2: 3: FC4h — Not a physical register. Unimplemented registers are read as ‘0’. These registers are implemented only on 40/44-pin devices. DS39760D-page 62 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 5-2: File Name TOSU REGISTER FILE SUMMARY (PIC18F2450/4450) Bit 7 Bit 6 Bit 5 — — — Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Top-of-Stack Upper Byte (TOS<20:16>) Value on Details POR, BOR on Page: ---0 0000 49, 54 TOSH Top-of-Stack High Byte (TOS<15:8>) 0000 0000 49, 54 TOSL Top-of-Stack Low Byte (TOS<7:0>) 0000 0000 49, 54 00-0 0000 49, 55 ---0 0000 49, 54 STKPTR STKFUL STKUNF — PCLATU — — — SP4 SP3 SP2 SP1 SP0 Holding Register for PC<20:16> PCLATH Holding Register for PC<15:8> 0000 0000 49, 54 PCL PC Low Byte (PC<7:0>) 0000 0000 49, 54 TBLPTRU — — bit 21(1) --00 0000 49, 76 TBLPTRH Program Memory Table Pointer High Byte (TBLPTR<15:8>) Program Memory Table Pointer Upper Byte (TBLPTR<20:16>) 0000 0000 49, 76 TBLPTRL Program Memory Table Pointer Low Byte (TBLPTR<7:0>) 0000 0000 49, 76 TABLAT Program Memory Table Latch 0000 0000 49, 76 PRODH Product Register High Byte xxxx xxxx 49, 83 PRODL Product Register Low Byte xxxx xxxx 49, 83 INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 49, 87 INTCON2 RBPU INTEDG0 INTEDG1 INTEDG2 — TMR0IP — RBIP 1111 -1-1 49, 88 INT2IP INT1IP — INT2IE INT1IE — INT2IF INT1IF INTCON3 11-0 0-00 49, 89 INDF0 Uses contents of FSR0 to address data memory – value of FSR0 not changed (not a physical register) N/A 49, 68 POSTINC0 Uses contents of FSR0 to address data memory – value of FSR0 post-incremented (not a physical register) N/A 49, 69 POSTDEC0 Uses contents of FSR0 to address data memory – value of FSR0 post-decremented (not a physical register) N/A 49, 69 PREINC0 Uses contents of FSR0 to address data memory – value of FSR0 pre-incremented (not a physical register) N/A 49, 69 PLUSW0 Uses contents of FSR0 to address data memory – value of FSR0 pre-incremented (not a physical register) – value of FSR0 offset by W N/A 49, 69 FSR0H ---- 0000 49, 68 FSR0L Indirect Data Memory Address Pointer 0 Low Byte — xxxx xxxx 49, 68 WREG Working Register xxxx xxxx 49, INDF1 Uses contents of FSR1 to address data memory – value of FSR1 not changed (not a physical register) N/A 49, 68 POSTINC1 Uses contents of FSR1 to address data memory – value of FSR1 post-incremented (not a physical register) N/A 49, 69 POSTDEC1 Uses contents of FSR1 to address data memory – value of FSR1 post-decremented (not a physical register) N/A 49, 69 PREINC1 Uses contents of FSR1 to address data memory – value of FSR1 pre-incremented (not a physical register) N/A 49, 69 PLUSW1 Uses contents of FSR1 to address data memory – value of FSR1 pre-incremented (not a physical register) – value of FSR1 offset by W N/A 49, 69 ---- 0000 49, 68 xxxx xxxx 49, 68 FSR1H — FSR1L — — — — — — Indirect Data Memory Address Pointer 0 High Byte Indirect Data Memory Address Pointer 1 High Byte Indirect Data Memory Address Pointer 1 Low Byte BSR — — — — Bank Select Register ---- 0000 49, 59 INDF2 Uses contents of FSR2 to address data memory – value of FSR2 not changed (not a physical register) N/A 50, 68 POSTINC2 Uses contents of FSR2 to address data memory – value of FSR2 post-incremented (not a physical register) N/A 50, 69 POSTDEC2 Uses contents of FSR2 to address data memory – value of FSR2 post-decremented (not a physical register) N/A 50, 69 PREINC2 Uses contents of FSR2 to address data memory – value of FSR2 pre-incremented (not a physical register) N/A 50, 69 PLUSW2 Uses contents of FSR2 to address data memory – value of FSR2 pre-incremented (not a physical register) – value of FSR2 offset by W N/A 50, 69 ---- 0000 50, 68 xxxx xxxx 50, 68 FSR2H — FSR2L — — — Indirect Data Memory Address Pointer 2 High Byte Indirect Data Memory Address Pointer 2 Low Byte STATUS — — TMR0H Timer0 Register High Byte TMR0L Timer0 Register Low Byte T0CON TMR0ON Legend: Note 1: 2: 3: 4: 5: 6: T08BIT — T0CS N T0SE OV PSA Z T0PS2 DC T0PS1 C T0PS0 ---x xxxx 50, 66 0000 0000 50, 113 xxxx xxxx 50, 113 1111 1111 50, 111 x = unknown, u = unchanged, - = unimplemented, q = value depends on condition. Shaded cells are unimplemented, read as ‘0’. Bit 21 of the TBLPTRU allows access to the device Configuration bits. The SBOREN bit is only available when BOREN<1:0> = 01; otherwise, the bit reads as ‘0’. These registers and/or bits are not implemented on 28-pin devices and are read as ‘0’. Reset values are shown for 40/44-pin devices; individual unimplemented bits should be interpreted as ‘-’. RA6 is configured as a port pin based on various primary oscillator modes. When the port pin is disabled, all of the associated bits read ‘0’. RE3 is only available as a port pin when the MCLRE Configuration bit is clear; otherwise, the bit reads as ‘0’. RC5 and RC4 are only available as port pins when the USB module is disabled (UCON<3> = 0). © 2008 Microchip Technology Inc. DS39760D-page 63 PIC18F2450/4450 TABLE 5-2: File Name REGISTER FILE SUMMARY (PIC18F2450/4450) (CONTINUED) Bit 6 OSCCON IDLEN — — — OSTS — SCS1 SCS0 0--- q-00 50, 31 HLVDCON VDIRMAG — IRVST HLVDEN HLVDL3 HLVDL2 HLVDL1 HLVDL0 0-00 0101 50, 185 WDTCON — — — — — — — SWDTEN --- ---0 50, 204 — RI TO PD POR BOR RCON IPEN SBOREN Bit 5 (2) TMR1H Timer1 Register High Byte TMR1L Timer1 Register Low Byte T1CON RD16 T1RUN TMR2 Timer2 Register PR2 Timer2 Period Register T2CON — T2OUTPS3 T1CKPS1 T2OUTPS2 ADRESH A/D Result Register High Byte ADRESL A/D Result Register Low Byte Bit 4 T1CKPS0 T2OUTPS1 Bit 3 T1OSCEN T2OUTPS0 Bit 2 T1SYNC TMR2ON Bit 1 TMR1CS T2CKPS1 Bit 0 Value on Details POR, BOR on Page: Bit 7 TMR1ON T2CKPS0 0q-1 11q0 50, 42 xxxx xxxx 50, 120 xxxx xxxx 50, 120 0000 0000 50, 115 0000 0000 50, 122 1111 1111 50, 122 -000 0000 50, 121 xxxx xxxx 50, 184 xxxx xxxx 50, 184 ADCON0 — — CHS3 CHS2 CHS1 CHS0 GO/DONE ADON --00 0000 50, 175 ADCON1 — — VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 --00 qqqq 50, 176 ADFM — ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0 ADCON2 CCPR1H Capture/Compare/PWM Register 1 High Byte CCPR1L Capture/Compare/PWM Register 1 Low Byte CCP1CON BAUDCON 0-00 0000 50, 177 xxxx xxxx 50, 124 xxxx xxxx 50, 124 — — DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 50, 123, ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN 01-0 0-00 51, 156, SPBRGH EUSART Baud Rate Generator Register High Byte 0000 0000 50, 157 SPBRG EUSART Baud Rate Generator Register Low Byte 0000 0000 50, 157 RCREG EUSART Receive Register 0000 0000 50, 165 TXREG EUSART Transmit Register 0000 0000 51, 163 TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 51, 154 RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 000x 51, 155 EECON2 0000 0000 51, 74 — CFGS — FREE WRERR WREN WR — -x-0 x00- 51, 75 IPR2 OSCFIP — USBIP — — HLVDIP — — 1-1- -1-- 51, 95 PIR2 OSCFIF — USBIF — — HLVDIF — — 0-0- -0-- 51, 91 PIE2 OSCFIE — USBIE — — HLVDIE — — 0-0- -0-- 51, 93 IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP -111 -111 51, 94 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF -000 -000 51, 90 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE -000 -000 51, 92 TRISE(3) — — — — — TRISE2 TRISE1 TRISE0 ---- -111 51, 110 TRISD(3) TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 1111 1111 51, 108 TRISC TRISC7 TRISC6 — — — TRISC2 TRISC1 TRISC0 11-- -111 51, 106 TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 1111 1111 51, 103 TRISA — TRISA6(4) TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 -111 1111 51, 100 LATE(3) — — — — — LATE2 LATE1 LATE0 ---- -xxx 51, 110 LATD(3) LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0 xxxx xxxx 51, 108 EECON1 Data Memory Control Register 2 (not a physical register) LATC LATC7 LATC6 — — — LATC2 LATC1 LATC0 xx-- -xxx 51, 106 LATB LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 xxxx xxxx 51, 103 LATA — LATA6(4) LATA5 LATA4 LATA3 LATA2 LATA1 LATA0 -xxx xxxx 51, 100 PORTE — — — — RE3(5) RE2(3) RE1(3) RE0(3) ---- x000 51, 109 RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 xxxx xxxx 51, 108 PORTD(3) Legend: Note 1: 2: 3: 4: 5: 6: x = unknown, u = unchanged, - = unimplemented, q = value depends on condition. Shaded cells are unimplemented, read as ‘0’. Bit 21 of the TBLPTRU allows access to the device Configuration bits. The SBOREN bit is only available when BOREN<1:0> = 01; otherwise, the bit reads as ‘0’. These registers and/or bits are not implemented on 28-pin devices and are read as ‘0’. Reset values are shown for 40/44-pin devices; individual unimplemented bits should be interpreted as ‘-’. RA6 is configured as a port pin based on various primary oscillator modes. When the port pin is disabled, all of the associated bits read ‘0’. RE3 is only available as a port pin when the MCLRE Configuration bit is clear; otherwise, the bit reads as ‘0’. RC5 and RC4 are only available as port pins when the USB module is disabled (UCON<3> = 0). DS39760D-page 64 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 5-2: File Name REGISTER FILE SUMMARY (PIC18F2450/4450) (CONTINUED) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on Details POR, BOR on Page: PORTC RC7 RC6 RC5(6) RC4(6) — RC2 RC1 RC0 xxxx -xxx 51, 106 PORTB RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxx xxxx 51, 100 PORTA — RA6(4) RA5 RA4 RA3 RA2 RA1 RA0 -x0x 0000 51, 100 UEP15 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 51, 135 UEP14 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 51, 135 UEP13 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 51, 135 UEP12 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 51, 135 UEP11 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 51, 135 UEP10 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 51, 135 UEP9 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 52, 135 UEP8 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 52, 135 UEP7 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 52, 135 UEP6 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 52, 135 UEP5 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 52, 135 UEP4 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 52, 135 UEP3 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 52, 135 UEP2 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 52, 135 UEP1 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 52, 135 UEP0 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL ---0 0000 52, 135 UCFG UTEYE UOEMON — UPUEN UTRDIS FSEN PPB1 PPB0 00-0 0000 52, 132 UADDR — ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0 -000 0000 52, 136 UCON — PPBRST SE0 PKTDIS USBEN RESUME SUSPND — -0x0 000- 52, 130 USTAT — ENDP3 ENDP2 ENDP1 ENDP0 DIR PPBI — -xxx xxx- 52, 134 UEIE BTSEE — — BTOEE DFN8EE CRC16EE CRC5EE PIDEE 0--0 0000 52, 148 UEIR BTSEF — — BTOEF DFN8EF CRC16EF CRC5EF PIDEF 0--0 0000 52, 147 UIE — SOFIE STALLIE IDLEIE TRNIE ACTVIE UERRIE URSTIE -000 0000 52, 146 UIR — SOFIF STALLIF IDLEIF TRNIF ACTVIF UERRIF URSTIF -000 0000 52, 144 UFRMH — — — — — FRM10 FRM9 FRM8 ---- -xxx 52, 136 UFRML FRM7 FRM6 FRM5 FRM4 FRM3 FRM2 FRM1 FRM0 xxxx xxxx 52, 136 Legend: Note 1: 2: 3: 4: 5: 6: x = unknown, u = unchanged, - = unimplemented, q = value depends on condition. Shaded cells are unimplemented, read as ‘0’. Bit 21 of the TBLPTRU allows access to the device Configuration bits. The SBOREN bit is only available when BOREN<1:0> = 01; otherwise, the bit reads as ‘0’. These registers and/or bits are not implemented on 28-pin devices and are read as ‘0’. Reset values are shown for 40/44-pin devices; individual unimplemented bits should be interpreted as ‘-’. RA6 is configured as a port pin based on various primary oscillator modes. When the port pin is disabled, all of the associated bits read ‘0’. RE3 is only available as a port pin when the MCLRE Configuration bit is clear; otherwise, the bit reads as ‘0’. RC5 and RC4 are only available as port pins when the USB module is disabled (UCON<3> = 0). © 2008 Microchip Technology Inc. DS39760D-page 65 PIC18F2450/4450 5.3.6 STATUS REGISTER The STATUS register, shown in Register 5-2, contains the arithmetic status of the ALU. As with any other SFR, it can be the operand for any instruction. If the STATUS register is the destination for an instruction that affects the Z, DC, C, OV or N bits, the results of the instruction are not written; instead, the STATUS register is updated according to the instruction performed. Therefore, the result of an instruction with the STATUS register as its destination may be different than intended. As an example, CLRF STATUS will set the Z bit and leave the remaining Status bits unchanged (‘000u u1uu’). REGISTER 5-2: It is recommended that only BCF, BSF, SWAPF, MOVFF and MOVWF instructions are used to alter the STATUS register because these instructions do not affect the Z, C, DC, OV or N bits in the STATUS register. For other instructions that do not affect Status bits, see the instruction set summaries in Table 19-2 and Table 19-3. Note: The C and DC bits operate as the Borrow and Digit Borrow bits, respectively, in subtraction. STATUS REGISTER U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x — — — N OV Z DC(1) C(2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-5 Unimplemented: Read as ‘0’ bit 4 N: Negative bit This bit is used for signed arithmetic (2’s complement). It indicates whether the result was negative (ALU MSB = 1). 1 = Result was negative 0 = Result was positive bit 3 OV: Overflow bit This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the 7-bit magnitude which causes the sign bit (bit 7 of the result) to change state. 1 = Overflow occurred for signed arithmetic (in this arithmetic operation) 0 = No overflow occurred bit 2 Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1 DC: Digit Carry/Borrow bit(1) For ADDWF, ADDLW, SUBLW and SUBWF instructions: 1 = A carry-out from the 4th low-order bit of the result occurred 0 = No carry-out from the 4th low-order bit of the result bit 0 C: Carry/Borrow bit(2) For ADDWF, ADDLW, SUBLW and SUBWF instructions: 1 = A carry-out from the Most Significant bit of the result occurred 0 = No carry-out from the Most Significant bit of the result occurred Note 1: 2: For borrow, the polarity is reversed. A subtraction is executed by adding the 2’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either bit 4 or bit 3 of the source register. For borrow, the polarity is reversed. A subtraction is executed by adding the 2’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low-order bit of the source register. DS39760D-page 66 © 2008 Microchip Technology Inc. PIC18F2450/4450 5.4 Data Addressing Modes Note: The execution of some instructions in the core PIC18 instruction set are changed when the PIC18 extended instruction set is enabled. See Section 5.6 “Data Memory and the Extended Instruction Set” for more information. While the program memory can be addressed in only one way – through the program counter – information in the data memory space can be addressed in several ways. For most instructions, the addressing mode is fixed. Other instructions may use up to three modes, depending on which operands are used and whether or not the extended instruction set is enabled. The addressing modes are: • • • • Inherent Literal Direct Indirect An additional addressing mode, Indexed Literal Offset, is available when the extended instruction set is enabled (XINST Configuration bit = 1). Its operation is discussed in greater detail in Section 5.6.1 “Indexed Addressing with Literal Offset”. 5.4.1 INHERENT AND LITERAL ADDRESSING Many PIC18 control instructions do not need any argument at all; they either perform an operation that globally affects the device or they operate implicitly on one register. This addressing mode is known as Inherent Addressing. Examples include SLEEP, RESET and DAW. Other instructions work in a similar way but require an additional explicit argument in the opcode. This is known as Literal Addressing mode because they require some literal value as an argument. Examples include ADDLW and MOVLW, which respectively, add or move a literal value to the W register. Other examples include CALL and GOTO, which include a 20-bit program memory address. 5.4.2 Purpose Register File”) or a location in the Access Bank (Section 5.3.3 “Access Bank”) as the data source for the instruction. The Access RAM bit ‘a’ determines how the address is interpreted. When ‘a’ is ‘1’, the contents of the BSR (Section 5.3.2 “Bank Select Register (BSR)”) are used with the address to determine the complete 12-bit address of the register. When ‘a’ is ‘0’, the address is interpreted as being a register in the Access Bank. Addressing that uses the Access RAM is sometimes also known as Direct Forced Addressing mode. A few instructions, such as MOVFF, include the entire 12-bit address (either source or destination) in their opcodes. In these cases, the BSR is ignored entirely. The destination of the operation’s results is determined by the destination bit ‘d’. When ‘d’ is ‘1’, the results are stored back in the source register, overwriting its original contents. When ‘d’ is ‘0’, the results are stored in the W register. Instructions without the ‘d’ argument have a destination that is implicit in the instruction; their destination is either the target register being operated on or the W register. 5.4.3 Indirect Addressing allows the user to access a location in data memory without giving a fixed address in the instruction. This is done by using File Select Registers (FSRs) as pointers to the locations to be read or written to. Since the FSRs are themselves located in RAM as Special Function Registers, they can also be directly manipulated under program control. This makes FSRs very useful in implementing data structures, such as tables and arrays in data memory. The registers for Indirect Addressing are also implemented with Indirect File Operands (INDFs) that permit automatic manipulation of the pointer value with auto-incrementing, auto-decrementing or offsetting with another value. This allows for efficient code, using loops, such as the example of clearing an entire RAM bank in Example 5-5. EXAMPLE 5-5: DIRECT ADDRESSING Direct Addressing mode specifies all or part of the source and/or destination address of the operation within the opcode itself. The options are specified by the arguments accompanying the instruction. In the core PIC18 instruction set, bit-oriented and byteoriented instructions use some version of Direct Addressing by default. All of these instructions include some 8-bit literal address as their Least Significant Byte. This address specifies either a register address in one of the banks of data RAM (Section 5.3.4 “General © 2008 Microchip Technology Inc. INDIRECT ADDRESSING NEXT LFSR CLRF BTFSS BRA CONTINUE HOW TO CLEAR RAM (BANK 1) USING INDIRECT ADDRESSING FSR0, 100h ; POSTINC0 ; Clear INDF ; register then ; inc pointer FSR0H, 1 ; All done with ; Bank1? NEXT ; NO, clear next ; YES, continue DS39760D-page 67 PIC18F2450/4450 5.4.3.1 FSR Registers and the INDF Operand mapped in the SFR space but are not physically implemented. Reading or writing to a particular INDF register actually accesses its corresponding FSR register pair. A read from INDF1, for example, reads the data at the address indicated by FSR1H:FSR1L. Instructions that use the INDF registers as operands actually use the contents of their corresponding FSR as a pointer to the instruction’s target. The INDF operand is just a convenient way of using the pointer. At the core of Indirect Addressing are three sets of registers: FSR0, FSR1 and FSR2. Each represents a pair of 8-bit registers: FSRnH and FSRnL. The four upper bits of the FSRnH register are not used, so each FSR pair holds a 12-bit value. This represents a value that can address the entire range of the data memory in a linear fashion. The FSR register pairs, then, serve as pointers to data memory locations. Because Indirect Addressing uses a full 12-bit address, data RAM banking is not necessary. Thus, the current contents of the BSR and the Access RAM bit have no effect on determining the target address. Indirect Addressing is accomplished with a set of Indirect File Operands, INDF0 through INDF2. These can be thought of as “virtual” registers; they are FIGURE 5-7: INDIRECT ADDRESSING 000h Using an instruction with one of the indirect addressing registers as the operand.... Bank 0 ADDWF, INDF1, 1 100h Bank 1 200h ...uses the 12-bit address stored in the FSR pair associated with that register.... 300h FSR1H:FSR1L 7 0 x x x x 1 1 1 0 7 Bank 2 0 1 1 0 0 1 1 0 0 Bank 3 through Bank 13 ...to determine the data memory location to be used in that operation. In this case, the FSR1 pair contains ECCh. This means the contents of location ECCh will be added to that of the W register and stored back in ECCh. E00h Bank 14 F00h FFFh Bank 15 Data Memory DS39760D-page 68 © 2008 Microchip Technology Inc. PIC18F2450/4450 5.4.3.2 FSR Registers and POSTINC, POSTDEC, PREINC and PLUSW In addition to the INDF operand, each FSR register pair also has four additional indirect operands. Like INDF, these are “virtual” registers that cannot be indirectly read or written to. Accessing these registers actually accesses the associated FSR register pair, but also performs a specific action on it stored value. They are: • POSTDEC: accesses the FSR value, then automatically decrements it by ‘1’ afterwards • POSTINC: accesses the FSR value, then automatically increments it by ‘1’ afterwards • PREINC: increments the FSR value by ‘1’, then uses it in the operation • PLUSW: adds the signed value of the W register (range of -127 to 128) to that of the FSR and uses the new value in the operation. In this context, accessing an INDF register uses the value in the FSR registers without changing them. Similarly, accessing a PLUSW register gives the FSR value offset by that in the W register; neither value is actually changed in the operation. Accessing the other virtual registers changes the value of the FSR registers. Operations on the FSRs with POSTDEC, POSTINC and PREINC affect the entire register pair; that is, rollovers of the FSRnL register from FFh to 00h carry over to the FSRnH register. On the other hand, results of these operations do not change the value of any flags in the STATUS register (e.g., Z, N, OV, etc.). 5.4.3.3 Operations by FSRs on FSRs Indirect Addressing operations that target other FSRs or virtual registers represent special cases. For example, using an FSR to point to one of the virtual registers will not result in successful operations. As a specific case, assume that FSR0H:FSR0L contains FE7h, the address of INDF1. Attempts to read the value of INDF1, using INDF0 as an operand, will return 00h. Attempts to write to INDF1, using INDF0 as the operand, will result in a NOP. On the other hand, using the virtual registers to write to an FSR pair may not occur as planned. In these cases, the value will be written to the FSR pair but without any incrementing or decrementing. Thus, writing to INDF2 or POSTDEC2 will write the same value to the FSR2H:FSR2L. Since the FSRs are physical registers mapped in the SFR space, they can be manipulated through all direct operations. Users should proceed cautiously when working on these registers, particularly if their code uses Indirect Addressing. Similarly, operations by Indirect Addressing are generally permitted on all other SFRs. Users should exercise the appropriate caution that they do not inadvertently change settings that might affect the operation of the device. The PLUSW register can be used to implement a form of Indexed Addressing in the data memory space. By manipulating the value in the W register, users can reach addresses that are fixed offsets from pointer addresses. In some applications, this can be used to implement some powerful program control structure, such as software stacks, inside of data memory. © 2008 Microchip Technology Inc. DS39760D-page 69 PIC18F2450/4450 5.5 Program Memory and the Extended Instruction Set The operation of program memory is unaffected by the use of the extended instruction set. Enabling the extended instruction set adds eight additional two-word commands to the existing PIC18 instruction set: ADDFSR, ADDULNK, CALLW, MOVSF, MOVSS, PUSHL, SUBFSR and SUBULNK. These instructions are executed as described in Section 5.2.4 “Two-Word Instructions”. 5.6 Data Memory and the Extended Instruction Set Enabling the PIC18 extended instruction set (XINST Configuration bit = 1) significantly changes certain aspects of data memory and its addressing. Specifically, the use of the Access Bank for many of the core PIC18 instructions is different. This is due to the introduction of a new addressing mode for the data memory space. This mode also alters the behavior of Indirect Addressing using FSR2 and its associated operands. What does not change is just as important. The size of the data memory space is unchanged, as well as its linear addressing. The SFR map remains the same. Core PIC18 instructions can still operate in both Direct and Indirect Addressing mode; inherent and literal instructions do not change at all. Indirect Addressing with FSR0 and FSR1 also remains unchanged. 5.6.1 INDEXED ADDRESSING WITH LITERAL OFFSET Enabling the PIC18 extended instruction set changes the behavior of Indirect Addressing using the FSR2 register pair and its associated file operands. Under the proper conditions, instructions that use the Access Bank – that is, most bit-oriented and byte-oriented instructions – can invoke a form of Indexed Addressing using an offset specified in the instruction. This special addressing mode is known as Indexed Addressing with Literal Offset or Indexed Literal Offset mode. DS39760D-page 70 When using the extended instruction set, this addressing mode requires the following: • The use of the Access Bank is forced (‘a’ = 0); and • The file address argument is less than or equal to 5Fh. Under these conditions, the file address of the instruction is not interpreted as the lower byte of an address (used with the BSR in Direct Addressing), or as an 8-bit address in the Access Bank. Instead, the value is interpreted as an offset value to an Address Pointer specified by FSR2. The offset and the contents of FSR2 are added to obtain the target address of the operation. 5.6.2 INSTRUCTIONS AFFECTED BY INDEXED LITERAL OFFSET MODE Any of the core PIC18 instructions that can use Direct Addressing are potentially affected by the Indexed Literal Offset Addressing mode. This includes all byteoriented and bit-oriented instructions, or almost one-half of the standard PIC18 instruction set. Instructions that only use Inherent or Literal Addressing modes are unaffected. Additionally, byte-oriented and bit-oriented instructions are not affected if they do not use the Access Bank (Access RAM bit is ‘1’) or include a file address of 60h or above. Instructions meeting these criteria will continue to execute as before. A comparison of the different possible addressing modes when the extended instruction set is enabled in shown in Figure 5-8. Those who desire to use byte-oriented or bit-oriented instructions in the Indexed Literal Offset mode should note the changes to assembler syntax for this mode. This is described in more detail in Section 19.2.1 “Extended Instruction Syntax”. © 2008 Microchip Technology Inc. PIC18F2450/4450 FIGURE 5-8: COMPARING ADDRESSING OPTIONS FOR BIT-ORIENTED AND BYTE-ORIENTED INSTRUCTIONS (EXTENDED INSTRUCTION SET ENABLED) EXAMPLE INSTRUCTION: ADDWF, f, d, a (Opcode: 0010 01da ffff ffff) When a = 0 and f ≥ 60h: The instruction executes in Direct Forced mode. ‘f’ is interpreted as a location in the Access RAM between 060h and 0FFh. This is the same as the SFRs or locations F60h to 0FFh (Bank 15) of data memory. 000h Locations below 60h are not available in this addressing mode. F00h 060h 080h 100h 00h Bank 1 through Bank 14 Bank 15 Note that in this mode, the correct syntax is now: ADDWF [k], d where ‘k’ is the same as ‘f’. When a = 1 (all values of f): The instruction executes in Direct mode (also known as Direct Long mode). ‘f’ is interpreted as a location in one of the 16 banks of the data memory space. The bank is designated by the Bank Select Register (BSR). The address can be in any implemented bank in the data memory space. 60h Valid range for ‘f’ Access RAM FFh F60h SFRs FFFh When a = 0 and f ≤ 5Fh: The instruction executes in Indexed Literal Offset mode. ‘f’ is interpreted as an offset to the address value in FSR2. The two are added together to obtain the address of the target register for the instruction. The address can be anywhere in the data memory space. Bank 0 Data Memory 000h Bank 0 080h 100h 001001da ffffffff Bank 1 through Bank 14 FSR2H FSR2L F00h F60h Bank 15 SFRs FFFh Data Memory BSR 00000000 000h Bank 0 080h 100h Bank 1 through Bank 14 F00h F60h 001001da ffffffff Bank 15 SFRs FFFh © 2008 Microchip Technology Inc. Data Memory DS39760D-page 71 PIC18F2450/4450 5.6.3 MAPPING THE ACCESS BANK IN INDEXED LITERAL OFFSET MODE The use of Indexed Literal Offset Addressing mode effectively changes how the lower portion of Access RAM (00h to 5Fh) is mapped. Rather than containing just the contents of the bottom half of Bank 0, this mode maps the contents from Bank 0 and a user-defined “window” that can be located anywhere in the data memory space. The value of FSR2 establishes the lower boundary of the addresses mapped into the window, while the upper boundary is defined by FSR2 plus 95 (5Fh). Addresses in the Access RAM above 5Fh are mapped as previously described (see Section 5.3.3 “Access Bank”). An example of Access Bank remapping in this addressing mode is shown in Figure 5-9. FIGURE 5-9: Remapping of the Access Bank applies only to operations using the Indexed Literal Offset mode. Operations that use the BSR (Access RAM bit is ‘1’) will continue to use Direct Addressing as before. Any indirect or indexed operation that explicitly uses any of the indirect file operands (including FSR2) will continue to operate as standard Indirect Addressing. Any instruction that uses the Access Bank, but includes a register address of greater than 05Fh, will use Direct Addressing and the normal Access Bank map. 5.6.4 BSR IN INDEXED LITERAL OFFSET MODE Although the Access Bank is remapped when the extended instruction set is enabled, the operation of the BSR remains unchanged. Direct Addressing, using the BSR to select the data memory bank, operates in the same manner as previously described. REMAPPING THE ACCESS BANK WITH INDEXED LITERAL OFFSET ADDRESSING Example Situation: ADDWF f, d, a 000h FSR2H:FSR2L = 120h Locations in the region from the FSR2 Pointer (120h) to the pointer plus 05Fh (17Fh) are mapped to the bottom of the Access RAM (000h-05Fh). Bank 0 100h 120h 17Fh 200h Special Function Registers at F60h through FFFh are mapped to 60h through FFh as usual. Bank 0 addresses below 5Fh are not available in this mode. They can still be addressed by using the BSR. Window Bank 1 00h Bank 1 “Window” 5Fh 60h Bank 2 through Bank 14 SFRs FFh Access Bank F00h F60h Bank 15 SFRs FFFh Data Memory DS39760D-page 72 © 2008 Microchip Technology Inc. PIC18F2450/4450 6.0 FLASH PROGRAM MEMORY 6.1 Table Reads and Table Writes The Flash program memory is readable, writable and erasable, during normal operation over the entire VDD range. In order to read and write program memory, there are two operations that allow the processor to move bytes between the program memory space and the data RAM: A read from program memory is executed on one byte at a time. A write to program memory is executed on blocks of 16 bytes at a time. Program memory is erased in blocks of 64 bytes at a time. A Bulk Erase operation may not be issued from user code. • Table Read (TBLRD) • Table Write (TBLWT) Writing or erasing program memory will cease instruction fetches until the operation is complete. The program memory cannot be accessed during the write or erase, therefore, code cannot execute. An internal programming timer terminates program memory writes and erases. A value written to program memory does not need to be a valid instruction. Executing a program memory location that forms an invalid instruction results in a NOP. The program memory space is 16 bits wide, while the data RAM space is 8 bits wide. Table reads and table writes move data between these two memory spaces through an 8-bit register (TABLAT). Table read operations retrieve data from program memory and place it into the data RAM space. Figure 6-1 shows the operation of a table read with program memory and data RAM. Table write operations store data from the data memory space into holding registers in program memory. The procedure to write the contents of the holding registers into program memory is detailed in Section 6.5 “Writing to Flash Program Memory”. Figure 6-2 shows the operation of a table write with program memory and data RAM. Table operations work with byte entities. A table block containing data, rather than program instructions, is not required to be word-aligned. Therefore, a table block can start and end at any byte address. If a table write is being used to write executable code into program memory, program instructions will need to be word-aligned. FIGURE 6-1: TABLE READ OPERATION Instruction: TBLRD* Program Memory Table Pointer(1) TBLPTRU TBLPTRH Table Latch (8-bit) TBLPTRL TABLAT Program Memory (TBLPTR) Note 1: Table Pointer register points to a byte in program memory. © 2008 Microchip Technology Inc. DS39760D-page 73 PIC18F2450/4450 FIGURE 6-2: TABLE WRITE OPERATION Instruction: TBLWT* Program Memory Holding Registers Table Pointer(1) TBLPTRU TBLPTRH Table Latch (8-bit) TBLPTRL TABLAT Program Memory (TBLPTR) Note 1: 6.2 Table Pointer actually points to one of 16 holding registers, the address of which is determined by TBLPTRL<3:0>. The process for physically writing data to the program memory array is discussed in Section 6.5 “Writing to Flash Program Memory”. Control Registers Several control registers are used in conjunction with the TBLRD and TBLWT instructions. These include the: • • • • EECON1 register EECON2 register TABLAT register TBLPTR registers 6.2.1 EECON1 AND EECON2 REGISTERS The EECON1 register (Register 6-1) is the control register for memory accesses. The EECON2 register is not a physical register; it is used exclusively in the memory write and erase sequences. Reading EECON2 will read all ‘0’s. The CFGS control bit determines if the access will be to the Configuration/Calibration registers or to program memory. DS39760D-page 74 The FREE bit, when set, will allow a program memory erase operation. When FREE is set, the erase operation is initiated on the next WR command. When FREE is clear, only writes are enabled. The WREN bit, when set, will allow a write operation. On power-up, the WREN bit is clear. The WRERR bit is set in hardware when the WREN bit is set and cleared when the internal programming timer expires and the write operation is complete. Note: During normal operation, the WRERR is read as ‘1’. This can indicate that a write operation was prematurely terminated by a Reset or a write operation was attempted improperly. The WR control bit initiates write operations. The bit cannot be cleared, only set, in software; it is cleared in hardware at the completion of the write operation. © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 6-1: EECON1: MEMORY CONTROL REGISTER 1 U-0 R/W-x U-0 R/W-0 R/W-x R/W-0 R/S-0 U-0 — CFGS — FREE WRERR(1) WREN WR — bit 7 bit 0 Legend: S = Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 Unimplemented: Read as ‘0’ bit 6 CFGS: Flash Program or Configuration Select bit 1 = Access Configuration registers 0 = Access Flash program bit 5 Unimplemented: Read as ‘0’ bit 4 FREE: Flash Row Erase Enable bit 1 = Erase the program memory row addressed by TBLPTR on the next WR command (cleared by completion of erase operation) 0 = Perform write-only bit 3 WRERR: Flash Program Error Flag bit(1) 1 = A write operation is prematurely terminated (any Reset during self-timed programming in normal operation or an improper write attempt) 0 = The write operation completed bit 2 WREN: Flash Program Write Enable bit 1 = Allows write cycles to Flash program 0 = Inhibits write cycles to Flash program bit 1 WR: Write Control bit 1 = Initiates a program memory erase cycle or write cycle (The operation is self-timed and the bit is cleared by hardware once write is complete. The WR bit can only be set (not cleared) in software.) 0 = Write cycle complete bit 0 Unimplemented: Read as ‘0’ Note 1: When a WRERR occurs, the CFGS bit is not cleared. This allows tracing of the error condition. © 2008 Microchip Technology Inc. DS39760D-page 75 PIC18F2450/4450 6.2.2 TABLE LATCH REGISTER (TABLAT) 6.2.4 The Table Latch (TABLAT) is an 8-bit register mapped into the SFR space. The Table Latch register is used to hold 8-bit data during data transfers between program memory and data RAM. 6.2.3 TBLPTR is used in reads, writes and erases of the Flash program memory. When a TBLRD is executed, all 22 bits of the TBLPTR determine which byte is read from program memory into TABLAT. TABLE POINTER REGISTER (TBLPTR) When a TBLWT is executed, the four LSbs of the Table Pointer register (TBLPTR<3:0>) determine which of the 16 program memory holding registers is written to. When the timed write to program memory begins (via the WR bit), the 16 MSbs of the TBLPTR (TBLPTR<21:4>) determine which program memory block of 16 bytes is written to. For more detail, see Section 6.5 “Writing to Flash Program Memory”. The Table Pointer (TBLPTR) register addresses a byte within the program memory. The TBLPTR is comprised of three SFR registers: Table Pointer Upper Byte, Table Pointer High Byte and Table Pointer Low Byte (TBLPTRU:TBLPTRH:TBLPTRL). These three registers join to form a 22-bit wide pointer. The low-order 21 bits allow the device to address up to 2 Mbytes of program memory space. The 22nd bit allows access to the device ID, the user ID and the Configuration bits. When an erase of program memory is executed, the 16 MSbs of the Table Pointer register (TBLPTR<21:6>) point to the 64-byte block that will be erased. The Least Significant bits (TBLPTR<5:0>) are ignored. The Table Pointer, TBLPTR, is used by the TBLRD and TBLWT instructions. These instructions can update the TBLPTR in one of four ways based on the table operation. These operations are shown in Table 6-1. These operations on the TBLPTR only affect the low-order 21 bits. TABLE 6-1: TABLE POINTER BOUNDARIES Figure 6-3 describes the relevant boundaries of the TBLPTR based on Flash program memory operations. TABLE POINTER OPERATIONS WITH TBLRD AND TBLWT INSTRUCTIONS Example Operation on Table Pointer TBLRD* TBLWT* TBLPTR is not modified TBLRD*+ TBLWT*+ TBLPTR is incremented after the read/write TBLRD*TBLWT*- TBLPTR is decremented after the read/write TBLRD+* TBLWT+* TBLPTR is incremented before the read/write FIGURE 6-3: 21 TABLE POINTER BOUNDARIES BASED ON OPERATION TBLPTRU 16 15 TBLPTRH 8 7 TBLPTRL 0 TABLE ERASE TBLPTR<21:6> TABLE WRITE – TBLPTR<21:4> TABLE READ – TBLPTR<21:0> DS39760D-page 76 © 2008 Microchip Technology Inc. PIC18F2450/4450 6.3 Reading the Flash Program Memory TBLPTR points to a byte address in program space. Executing TBLRD places the byte pointed to into TABLAT. In addition, TBLPTR can be modified automatically for the next table read operation. The TBLRD instruction is used to retrieve data from program memory and places it into data RAM. Table reads from program memory are performed one byte at a time. FIGURE 6-4: The internal program memory is typically organized by words. The Least Significant bit of the address selects between the high and low bytes of the word. Figure 6-4 shows the interface between the internal program memory and the TABLAT. READS FROM FLASH PROGRAM MEMORY Program Memory (Even Byte Address) (Odd Byte Address) TBLPTR = xxxxx1 Instruction Register (IR) EXAMPLE 6-1: FETCH TBLRD TBLPTR = xxxxx0 TABLAT Read Register READING A FLASH PROGRAM MEMORY WORD MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF CODE_ADDR_UPPER TBLPTRU CODE_ADDR_HIGH TBLPTRH CODE_ADDR_LOW TBLPTRL ; Load TBLPTR with the base ; address of the word READ_WORD TBLRD*+ MOVF MOVWF TBLRD*+ MOVF MOVF TABLAT, W WORD_EVEN TABLAT, W WORD_ODD © 2008 Microchip Technology Inc. ; read into TABLAT and increment ; get data ; read into TABLAT and increment ; get data DS39760D-page 77 PIC18F2450/4450 6.4 Erasing Flash Program Memory 6.4.1 The minimum erase block is 32 words or 64 bytes. Only through the use of an external programmer, or through ICSP control, can larger blocks of program memory be Bulk Erased. Word Erase in the Flash array is not supported. The sequence of events for erasing a block of internal program memory is: 1. When initiating an erase sequence from the microcontroller itself, a block of 64 bytes of program memory is erased. The Most Significant 16 bits of the TBLPTR<21:6> point to the block being erased. TBLPTR<5:0> are ignored. 2. 3. 4. 5. 6. The EECON1 register commands the erase operation. The WREN bit must be set to enable write operations. The FREE bit is set to select an erase operation. For protection, the write initiate sequence for EECON2 must be used. 7. A long write is necessary for erasing the internal Flash. Instruction execution is halted while in a long write cycle. The long write will be terminated by the internal programming timer. EXAMPLE 6-2: FLASH PROGRAM MEMORY ERASE SEQUENCE 8. Load Table Pointer register with address of row being erased. Set the EECON1 register for the erase operation: • clear the CFGS bit to access program memory; • set WREN bit to enable writes; • set FREE bit to enable the erase. Disable interrupts. Write 55h to EECON2. Write 0AAh to EECON2. Set the WR bit. This will begin the Row Erase cycle. The CPU will stall for duration of the erase (about 2 ms using internal timer). Re-enable interrupts. ERASING A FLASH PROGRAM MEMORY ROW MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF CODE_ADDR_UPPER TBLPTRU CODE_ADDR_HIGH TBLPTRH CODE_ADDR_LOW TBLPTRL ; load TBLPTR with the base ; address of the memory block BCF BSF BSF BCF MOVLW MOVWF MOVLW MOVWF BSF BSF EECON1, EECON1, EECON1, INTCON, 55h EECON2 0AAh EECON2 EECON1, INTCON, ; ; ; ; ERASE_ROW Required Sequence DS39760D-page 78 CFGS WREN FREE GIE access Flash program memory enable write to memory enable Row Erase operation disable interrupts ; write 55h WR GIE ; write 0AAh ; start erase (CPU stall) ; re-enable interrupts © 2008 Microchip Technology Inc. PIC18F2450/4450 6.5 Writing to Flash Program Memory The long write is necessary for programming the internal Flash. Instruction execution is halted while in a long write cycle. The long write will be terminated by the internal programming timer. The minimum programming block is 8 words or 16 bytes. Word or byte programming is not supported. Table writes are used internally to load the holding registers needed to program the Flash memory. There are 16 holding registers used by the table writes for programming. The write/erase voltages are generated by an on-chip charge pump, rated to operate over the voltage range of the device. Since the Table Latch (TABLAT) is only a single byte, the TBLWT instruction may need to be executed 16 times for each programming operation. All of the table write operations will essentially be short writes because only the holding registers are written. At the end of updating the 16 holding registers, the EECON1 register must be written to in order to start the programming operation with a long write. FIGURE 6-5: Note: The default value of the holding registers on device Resets and after write operations is FFh. A write of FFh to a holding register does not modify that byte. This means that individual bytes of program memory may be modified, provided that the change does not attempt to change any bit from a ‘0’ to a ‘1’. When modifying individual bytes, it is not necessary to load all 16 holding registers before executing a write operation. TABLE WRITES TO FLASH PROGRAM MEMORY TABLAT Write Register 8 8 TBLPTR = xxxxx0 8 TBLPTR = xxxxx1 Holding Register TBLPTR = xxxxx2 Holding Register 8 TBLPTR = xxxxxF Holding Register Holding Register Program Memory 6.5.1 FLASH PROGRAM MEMORY WRITE SEQUENCE The sequence of events for programming an internal program memory location should be: 1. 2. 3. 4. 5. 6. 7. 8. 9. Read 64 bytes into RAM. Update data values in RAM as necessary. Load Table Pointer register with address being erased. Execute the Row Erase procedure. Load Table Pointer register with address of first byte being written. Write 16 bytes into the holding registers with auto-increment. Set the EECON1 register for the write operation: • clear the CFGS bit to access program memory; • set WREN to enable byte writes. Disable interrupts. Write 55h to EECON2. © 2008 Microchip Technology Inc. 10. Write 0AAh to EECON2. 11. Set the WR bit. This will begin the write cycle. 12. The CPU will stall for duration of the write (about 2 ms using internal timer). 13. Re-enable interrupts. 14. Repeat steps 6 through 14 once more to write 64 bytes. 15. Verify the memory (table read). This procedure will require about 8 ms to update one row of 64 bytes of memory. An example of the required code is given in Example 6-3. Note: Before setting the WR bit, the Table Pointer address needs to be within the intended address range of the 16 bytes in the holding register. DS39760D-page 79 PIC18F2450/4450 EXAMPLE 6-3: WRITING TO FLASH PROGRAM MEMORY MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF D'64’ COUNTER BUFFER_ADDR_HIGH FSR0H BUFFER_ADDR_LOW FSR0L CODE_ADDR_UPPER TBLPTRU CODE_ADDR_HIGH TBLPTRH CODE_ADDR_LOW TBLPTRL ; number of bytes in erase block TBLRD*+ MOVF MOVWF DECFSZ BRA TABLAT, W POSTINC0 COUNTER READ_BLOCK MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF DATA_ADDR_HIGH FSR0H DATA_ADDR_LOW FSR0L NEW_DATA_LOW POSTINC0 NEW_DATA_HIGH INDF0 ; point to buffer MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF BCF BSF BSF BCF CODE_ADDR_UPPER TBLPTRU CODE_ADDR_HIGH TBLPTRH CODE_ADDR_LOW TBLPTRL EECON1, CFGS EECON1, WREN EECON1, FREE INTCON, GIE ; load TBLPTR with the base ; address of the memory block ; point to buffer ; Load TBLPTR with the base ; address of the memory block READ_BLOCK ; ; ; ; ; read into TABLAT, and inc get data store data done? repeat MODIFY_WORD ; update buffer word ERASE_BLOCK MOVLW MOVWF MOVLW MOVWF BSF BSF TBLRD*MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF WRITE_BUFFER_BACK MOVLW MOVWF WRITE_BYTE_TO_HREGS MOVF MOVWF TBLWT+* Required Sequence DECFSZ BRA DS39760D-page 80 55h EECON2 0AAh EECON2 EECON1, WR INTCON, GIE BUFFER_ADDR_HIGH FSR0H BUFFER_ADDR_LOW FSR0L D’4’ COUNTER1 ; ; ; ; access Flash program memory enable write to memory enable Row Erase operation disable interrupts ; write 55h ; ; ; ; ; write 0AAh start erase (CPU stall) re-enable interrupts dummy read decrement point to buffer D’16’ COUNTER ; number of bytes in holding register POSTINC0, W TABLAT ; ; ; ; ; COUNTER WRITE_WORD_TO_HREGS get low byte of buffer data present data to table latch write data, perform a short write to internal TBLWT holding register. loop until buffers are full © 2008 Microchip Technology Inc. PIC18F2450/4450 EXAMPLE 6-3: WRITING TO FLASH PROGRAM MEMORY (CONTINUED) PROGRAM_MEMORY Required Sequence 6.5.2 BCF BSF BCF EECON1, CFGS EECON1, WREN INTCON, GIE ; access Flash program memory ; enable write to memory ; disable interrupts MOVLW MOVWF MOVLW MOVWF BSF DECFSZ BRA BSF BCF 55h EECON2 0AAh EECON2 EECON1, WR COUNTER1 WRITE_BUFFER_BACK INTCON, GIE EECON1, WREN UNEXPECTED TERMINATION OF WRITE OPERATION ; re-enable interrupts ; disable write to memory PROTECTION AGAINST SPURIOUS WRITES To protect against spurious writes to Flash program memory, the write initiate sequence must also be followed. See Section 18.0 “Special Features of the CPU” for more detail. 6.6 If a write is terminated by an unplanned event, such as loss of power or an unexpected Reset, the memory location just programmed should be verified and reprogrammed if needed. If the write operation is interrupted by a MCLR Reset or a WDT time-out Reset during normal operation, the user can check the WRERR bit and rewrite the location(s) as needed. TABLE 6-2: ; write 0AAh ; start program (CPU stall) 6.5.4 WRITE VERIFY Depending on the application, good programming practice may dictate that the value written to the memory should be verified against the original value. This should be used in applications where excessive writes can stress bits near the specification limit. 6.5.3 ; write 55h Flash Program Operation During Code Protection See Section 18.5 “Program Verification and Code Protection” for details on code protection of Flash program memory. REGISTERS ASSOCIATED WITH PROGRAM FLASH MEMORY Name Bit 7 Bit 6 Bit 5 TBLPTRU — — bit 21 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Program Memory Table Pointer Upper Byte (TBLPTR<20:16>) Reset Values on Page: 49 TBPLTRH Program Memory Table Pointer High Byte (TBLPTR<15:8>) 49 TBLPTRL Program Memory Table Pointer Low Byte (TBLPTR<7:0>) 49 TABLAT Program Memory Table Latch INTCON GIE/GIEH PEIE/GIEL TMR0IE 49 EECON2 Data Memory Control Register 2 (not a physical register) INT0IE RBIE TMR0IF INT0IF RBIF 49 51 — CFGS — FREE WRERR WREN WR — 51 IPR2 OSCFIP — USBIP — — HLVDIP — — 51 PIR2 OSCFIF — USBIF — — HLVDIF — — 51 PIE2 OSCFIE — USBIE — — HLVDIE — — 51 EECON1 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used during Flash access. © 2008 Microchip Technology Inc. DS39760D-page 81 PIC18F2450/4450 NOTES: DS39760D-page 82 © 2008 Microchip Technology Inc. PIC18F2450/4450 7.0 8 x 8 HARDWARE MULTIPLIER 7.1 Introduction EXAMPLE 7-1: MOVF MULWF All PIC18 devices include an 8 x 8 hardware multiplier as part of the ALU. The multiplier performs an unsigned operation and yields a 16-bit result that is stored in the product register pair, PRODH:PRODL. The multiplier’s operation does not affect any flags in the STATUS register. ARG1, W ARG2 ; ; ARG1 * ARG2 -> ; PRODH:PRODL EXAMPLE 7-2: Making multiplication a hardware operation allows it to be completed in a single instruction cycle. This has the advantages of higher computational throughput and reduced code size for multiplication algorithms and allows the PIC18 devices to be used in many applications previously reserved for digital signal processors. A comparison of various hardware and software multiply operations, along with the savings in memory and execution time, is shown in Table 7-1. 7.2 8 x 8 UNSIGNED MULTIPLY ROUTINE 8 x 8 SIGNED MULTIPLY ROUTINE MOVF MULWF ARG1, W ARG2 BTFSC SUBWF ARG2, SB PRODH, F MOVF BTFSC SUBWF ARG2, W ARG1, SB PRODH, F Operation ; ; ; ; ; ARG1 * ARG2 -> PRODH:PRODL Test Sign Bit PRODH = PRODH - ARG1 ; Test Sign Bit ; PRODH = PRODH ; - ARG2 Example 7-1 shows the instruction sequence for an 8 x 8 unsigned multiplication. Only one instruction is required when one of the arguments is already loaded in the WREG register. Example 7-2 shows the sequence to do an 8 x 8 signed multiplication. To account for the sign bits of the arguments, each argument’s Most Significant bit (MSb) is tested and the appropriate subtractions are done. TABLE 7-1: PERFORMANCE COMPARISON FOR VARIOUS MULTIPLY OPERATIONS Routine 8 x 8 unsigned 8 x 8 signed 16 x 16 unsigned 16 x 16 signed Multiply Method Program Memory (Words) Cycles (Max) @ 40 MHz @ 10 MHz @ 4 MHz Without hardware multiply 13 69 6.9 μs 27.6 μs 69 μs Time Hardware multiply 1 1 100 ns 400 ns 1 μs Without hardware multiply 33 91 9.1 μs 36.4 μs 91 μs Hardware multiply 6 6 600 ns 2.4 μs 6 μs Without hardware multiply 21 242 24.2 μs 96.8 μs 242 μs Hardware multiply 28 28 2.8 μs 11.2 μs 28 μs Without hardware multiply 52 254 25.4 μs 102.6 μs 254 μs Hardware multiply 35 40 4.0 μs 16.0 μs 40 μs © 2008 Microchip Technology Inc. DS39760D-page 83 PIC18F2450/4450 Example 7-3 shows the sequence to do a 16 x 16 unsigned multiplication. Equation 7-1 shows the algorithm that is used. The 32-bit result is stored in four registers (RES3:RES0). EQUATION 7-1: RES3:RES0 = = EXAMPLE 7-3: 16 x 16 UNSIGNED MULTIPLICATION ALGORITHM ARG1H:ARG1L • ARG2H:ARG2L (ARG1H • ARG2H • 216) + (ARG1H • ARG2L • 28) + (ARG1L • ARG2H • 28) + (ARG1L • ARG2L) EQUATION 7-2: RES3:RES0= ARG1H:ARG1L • ARG2H:ARG2L = (ARG1H • ARG2H • 216) + (ARG1H • ARG2L • 28) + (ARG1L • ARG2H • 28) + (ARG1L • ARG2L) + (-1 • ARG2H<7> • ARG1H:ARG1L • 216) + (-1 • ARG1H<7> • ARG2H:ARG2L • 216) EXAMPLE 7-4: 16 x 16 UNSIGNED MULTIPLY ROUTINE MOVF MULWF ARG1L, W ARG2L MOVFF MOVFF PRODH, RES1 PRODL, RES0 MOVF MULWF ARG1H, W ARG2H MOVFF MOVFF PRODH, RES3 PRODL, RES2 MOVF MULWF ARG1L, W ARG2H MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F MOVF MULWF ARG1H, W ARG2L MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F ; ARG1L * ARG2L-> ; PRODH:PRODL ; ; ARG1L * ARG2H-> PRODH:PRODL Add cross products ARG1H * ARG2L-> PRODH:PRODL Add cross products Example 7-4 shows the sequence to do a 16 x 16 signed multiply. Equation 7-2 shows the algorithm used. The 32-bit result is stored in four registers (RES3:RES0). To account for the sign bits of the arguments, the MSb for each argument pair is tested and the appropriate subtractions are done. DS39760D-page 84 ARG1L, W ARG2L MOVFF MOVFF PRODH, RES1 PRODL, RES0 MOVF MULWF ARG1H, W ARG2H MOVFF MOVFF PRODH, RES3 PRODL, RES2 MOVF MULWF ARG1L,W ARG2H MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F MOVF MULWF ARG1H, W ARG2L MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F BTFSS BRA MOVF SUBWF MOVF SUBWFB ARG2H, 7 SIGN_ARG1 ARG1L, W RES2 ARG1H, W RES3 ; ARG2H:ARG2L neg? ; no, check ARG1 ; ; ; ARG1H, 7 CONT_CODE ARG2L, W RES2 ARG2H, W RES3 ; ARG1H:ARG1L neg? ; no, done ; ; ; ; ARG1L * ARG2L -> ; PRODH:PRODL ; ; ; ARG1H * ARG2H -> ; PRODH:PRODL ; ; ; ; ; ; ; ; ; ; ARG1L * ARG2H -> PRODH:PRODL Add cross products ; ; ; ; ; ; ; ; ; ; ; MOVF MULWF ; ; ; ; ; ; ; ; ; ; 16 x 16 SIGNED MULTIPLY ROUTINE ; ; ; ARG1H * ARG2H-> ; PRODH:PRODL ; ; 16 x 16 SIGNED MULTIPLICATION ALGORITHM ; ; ; ; ; ; ; ; ; ARG1H * ARG2L -> PRODH:PRODL Add cross products ; ; SIGN_ARG1 BTFSS BRA MOVF SUBWF MOVF SUBWFB ; CONT_CODE : © 2008 Microchip Technology Inc. PIC18F2450/4450 8.0 INTERRUPTS The PIC18F2450/4450 devices have multiple interrupt sources and an interrupt priority feature that allows each interrupt source to be assigned a high-priority level or a low-priority level. The high-priority interrupt vector is at 000008h and the low-priority interrupt vector is at 000018h. High-priority interrupt events will interrupt any low-priority interrupts that may be in progress. There are ten registers which are used to control interrupt operation. These registers are: • • • • • • • RCON INTCON INTCON2 INTCON3 PIR1, PIR2 PIE1, PIE2 IPR1, IPR2 It is recommended that the Microchip header files supplied with MPLAB® IDE be used for the symbolic bit names in these registers. This allows the assembler/ compiler to automatically take care of the placement of these bits within the specified register. When an interrupt is responded to, the global interrupt enable bit is cleared to disable further interrupts. If the IPEN bit is cleared, this is the GIE bit. If interrupt priority levels are used, this will be either the GIEH or GIEL bit. High-priority interrupt sources can interrupt a lowpriority interrupt. Low-priority interrupts are not processed while high-priority interrupts are in progress. The return address is pushed onto the stack and the PC is loaded with the interrupt vector address (000008h or 000018h). Once in the Interrupt Service Routine, the source(s) of the interrupt can be determined by polling the interrupt flag bits. The interrupt flag bits must be cleared in software before re-enabling interrupts to avoid recursive interrupts. The “return from interrupt” instruction, RETFIE, exits the interrupt routine and sets the GIE bit (GIEH or GIEL if priority levels are used) which re-enables interrupts. For external interrupt events, such as the INTx pins or the PORTB input change interrupt, the interrupt latency will be three to four instruction cycles. The exact latency is the same for one or two-cycle instructions. Individual interrupt flag bits are set regardless of the status of their corresponding enable bit or the GIE bit. Note: Each interrupt source has three bits to control its operation. The functions of these bits are: • Flag bit to indicate that an interrupt event occurred • Enable bit that allows program execution to branch to the interrupt vector address when the flag bit is set • Priority bit to select high priority or low priority The interrupt priority feature is enabled by setting the IPEN bit (RCON<7>). When interrupt priority is enabled, there are two bits which enable interrupts globally. Setting the GIEH bit (INTCON<7>) enables all interrupts that have the priority bit set (high priority). Setting the GIEL bit (INTCON<6>) enables all interrupts that have the priority bit cleared (low priority). When the interrupt flag, enable bit and appropriate global interrupt enable bit are set, the interrupt will vector immediately to address 000008h or 000018h, depending on the priority bit setting. Individual interrupts can be disabled through their corresponding enable bits. When the IPEN bit is cleared (default state), the interrupt priority feature is disabled and interrupts are compatible with PIC® mid-range microcontrollers. In Compatibility mode, the interrupt priority bits for each source have no effect. INTCON<6> is the PEIE bit which enables/disables all peripheral interrupt sources. INTCON<7> is the GIE bit which enables/disables all interrupt sources. All interrupts branch to address 000008h in Compatibility mode. © 2008 Microchip Technology Inc. 8.1 Do not use the MOVFF instruction to modify any of the interrupt control registers while any interrupt is enabled. Doing so may cause erratic microcontroller behavior. USB Interrupts Unlike other peripherals, the USB module is capable of generating a wide range of interrupts for many types of events. These include several types of normal communication and status events and several module level error events. To handle these events, the USB module is equipped with its own interrupt logic. The logic functions in a manner similar to the microcontroller level interrupt funnel, with each interrupt source having separate flag and enable bits. All events are funneled to a single device level interrupt, USBIF (PIR2<5>). Unlike the device level interrupt logic, the individual USB interrupt events cannot be individually assigned their own priority. This is determined at the device level interrupt funnel for all USB events by the USBIP bit. For additional details on USB interrupt logic, refer to Section 14.5 “USB Interrupts”. DS39760D-page 85 PIC18F2450/4450 FIGURE 8-1: INTERRUPT LOGIC TMR0IF TMR0IE TMR0IP RBIF RBIE RBIP INT0IF INT0IE Interrupt to CPU Vector to Location 0008h INT1IF INT1IE INT1IP INT2IF INT2IE INT2IP Peripheral Interrupt Flag bit Peripheral Interrupt Enable bit Peripheral Interrupt Priority bit GIE/GIEH TMR1IF TMR1IE TMR1IP From USB Interrupt Logic Wake-up if in Sleep Mode IPEN IPEN USBIF USBIE USBIP PEIE/GIEL IPEN Additional Peripheral Interrupts High-Priority Interrupt Generation Low-Priority Interrupt Generation Peripheral Interrupt Flag bit Peripheral Interrupt Enable bit Peripheral Interrupt Priority bit TMR1IF TMR1IE TMR1IP From USB Interrupt Logic RBIF RBIE RBIP USBIF USBIE USBIP Additional Peripheral Interrupts DS39760D-page 86 Interrupt to CPU Vector to Location 0018h TMR0IF TMR0IE TMR0IP PEIE/GIEL GIE/GIEH INT1IF INT1IE INT1IP INT2IF INT2IE INT2IP © 2008 Microchip Technology Inc. PIC18F2450/4450 8.2 INTCON Registers Note: The INTCON registers are readable and writable registers which contain various enable, priority and flag bits. REGISTER 8-1: Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the global interrupt enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling. INTCON: INTERRUPT CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-x GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 GIE/GIEH: Global Interrupt Enable bit When IPEN = 0: 1 = Enables all unmasked interrupts 0 = Disables all interrupts When IPEN = 1: 1 = Enables all high-priority interrupts 0 = Disables all interrupts bit 6 PEIE/GIEL: Peripheral Interrupt Enable bit When IPEN = 0: 1 = Enables all unmasked peripheral interrupts 0 = Disables all peripheral interrupts When IPEN = 1: 1 = Enables all low-priority peripheral interrupts 0 = Disables all low-priority peripheral interrupts bit 5 TMR0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 overflow interrupt 0 = Disables the TMR0 overflow interrupt bit 4 INT0IE: INT0 External Interrupt Enable bit 1 = Enables the INT0 external interrupt 0 = Disables the INT0 external interrupt bit 3 RBIE: RB Port Change Interrupt Enable bit 1 = Enables the RB port change interrupt 0 = Disables the RB port change interrupt bit 2 TMR0IF: TMR0 Overflow Interrupt Flag bit 1 = TMR0 register has overflowed (must be cleared in software) 0 = TMR0 register did not overflow bit 1 INT0IF: INT0 External Interrupt Flag bit 1 = The INT0 external interrupt occurred (must be cleared in software) 0 = The INT0 external interrupt did not occur bit 0 RBIF: RB Port Change Interrupt Flag bit(1) 1 = At least one of the RB7:RB4 pins changed state (must be cleared in software) 0 = None of the RB7:RB4 pins have changed state Note 1: A mismatch condition will continue to set this bit. Reading PORTB and waiting 1 TCY will end the mismatch condition and allow the bit to be cleared. © 2008 Microchip Technology Inc. DS39760D-page 87 PIC18F2450/4450 REGISTER 8-2: INTCON2: INTERRUPT CONTROL REGISTER 2 R/W-1 R/W-1 INTEDG0 RBPU R/W-1 INTEDG1 R/W-1 U-0 INTEDG2 — R/W-1 U-0 R/W-1 TMR0IP — RBIP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 RBPU: PORTB Pull-up Enable bit 1 = All PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled by individual port latch values bit 6 INTEDG0: External Interrupt 0 Edge Select bit 1 = Interrupt on rising edge 0 = Interrupt on falling edge bit 5 INTEDG1: External Interrupt 1 Edge Select bit 1 = Interrupt on rising edge 0 = Interrupt on falling edge bit 4 INTEDG2: External Interrupt 2 Edge Select bit 1 = Interrupt on rising edge 0 = Interrupt on falling edge bit 3 Unimplemented: Read as ‘0’ bit 2 TMR0IP: TMR0 Overflow Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 Unimplemented: Read as ‘0’ bit 0 RBIP: RB Port Change Interrupt Priority bit 1 = High priority 0 = Low priority Note: x = Bit is unknown Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the global interrupt enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling. DS39760D-page 88 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 8-3: INTCON3: INTERRUPT CONTROL REGISTER 3 R/W-1 R/W-1 U-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 INT2IP INT1IP — INT2IE INT1IE — INT2IF INT1IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 INT2IP: INT2 External Interrupt Priority bit 1 = High priority 0 = Low priority bit 6 INT1IP: INT1 External Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 Unimplemented: Read as ‘0’ bit 4 INT2IE: INT2 External Interrupt Enable bit 1 = Enables the INT2 external interrupt 0 = Disables the INT2 external interrupt bit 3 INT1IE: INT1 External Interrupt Enable bit 1 = Enables the INT1 external interrupt 0 = Disables the INT1 external interrupt bit 2 Unimplemented: Read as ‘0’ bit 1 INT2IF: INT2 External Interrupt Flag bit 1 = The INT2 external interrupt occurred (must be cleared in software) 0 = The INT2 external interrupt did not occur bit 0 INT1IF: INT1 External Interrupt Flag bit 1 = The INT1 external interrupt occurred (must be cleared in software) 0 = The INT1 external interrupt did not occur Note: x = Bit is unknown Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the global interrupt enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling. © 2008 Microchip Technology Inc. DS39760D-page 89 PIC18F2450/4450 8.3 PIR Registers The PIR registers contain the individual flag bits for the peripheral interrupts. Due to the number of peripheral interrupt sources, there are two Peripheral Interrupt Request (Flag) registers (PIR1 and PIR2). REGISTER 8-4: Note 1: Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the Global Interrupt Enable bit, GIE (INTCON<7>). 2: User software should ensure the appropriate interrupt flag bits are cleared prior to enabling an interrupt and after servicing that interrupt. PIR1: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 1 U-0 R/W-0 R-0 R-0 U-0 R/W-0 R/W-0 R/W-0 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 Unimplemented: Read as ‘0’ bit 6 ADIF: A/D Converter Interrupt Flag bit 1 = An A/D conversion completed (must be cleared in software) 0 = The A/D conversion is not complete bit 5 RCIF: EUSART Receive Interrupt Flag bit 1 = The EUSART receive buffer, RCREG, is full (cleared when RCREG is read) 0 = The EUSART receive buffer is empty bit 4 TXIF: EUSART Transmit Interrupt Flag bit 1 = The EUSART transmit buffer, TXREG, is empty (cleared when TXREG is written) 0 = The EUSART transmit buffer is full bit 3 Unimplemented: Read as ‘0’ bit 2 CCP1IF: CCP1 Interrupt Flag bit Capture mode: 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare mode: 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM mode: Unused in this mode. bit 1 TMR2IF: TMR2 to PR2 Match Interrupt Flag bit 1 = TMR2 to PR2 match occurred (must be cleared in software) 0 = No TMR2 to PR2 match occurred bit 0 TMR1IF: TMR1 Overflow Interrupt Flag bit 1 = TMR1 register overflowed (must be cleared in software) 0 = TMR1 register did not overflow DS39760D-page 90 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 8-5: PIR2: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 2 R/W-0 U-0 R/W-0 U-0 U-0 R/W-0 U-0 U-0 OSCFIF — USBIF — — HLVDIF — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 OSCFIF: Oscillator Fail Interrupt Flag bit 1 = System oscillator failed, clock input has changed to INTRC (must be cleared in software) 0 = System clock operating bit 6 Unimplemented: Read as ‘0’ bit 5 USBIF: USB Interrupt Flag bit 1 = USB has requested an interrupt (must be cleared in software) 0 = No USB interrupt request bit 4-3 Unimplemented: Read as ‘0’ bit 2 HLVDIF: High/Low-Voltage Detect Interrupt Flag bit 1 = A high/low-voltage condition occurred 0 = No high/low-voltage event has occurred bit 1-0 Unimplemented: Read as ‘0’ © 2008 Microchip Technology Inc. DS39760D-page 91 PIC18F2450/4450 8.4 PIE Registers The PIE registers contain the individual enable bits for the peripheral interrupts. Due to the number of peripheral interrupt sources, there are two Peripheral Interrupt Enable registers (PIE1 and PIE2). When IPEN = 0, the PEIE bit must be set to enable any of these peripheral interrupts. REGISTER 8-6: PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1 U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 Unimplemented: Read as ‘0’ bit 6 ADIE: A/D Converter Interrupt Enable bit 1 = Enables the A/D interrupt 0 = Disables the A/D interrupt bit 5 RCIE: EUSART Receive Interrupt Enable bit 1 = Enables the EUSART receive interrupt 0 = Disables the EUSART receive interrupt bit 4 TXIE: EUSART Transmit Interrupt Enable bit 1 = Enables the EUSART transmit interrupt 0 = Disables the EUSART transmit interrupt bit 3 Unimplemented: Read as ‘0’ bit 2 CCP1IE: CCP1 Interrupt Enable bit 1 = Enables the CCP1 interrupt 0 = Disables the CCP1 interrupt bit 1 TMR2IE: TMR2 to PR2 Match Interrupt Enable bit 1 = Enables the TMR2 to PR2 match interrupt 0 = Disables the TMR2 to PR2 match interrupt bit 0 TMR1IE: TMR1 Overflow Interrupt Enable bit 1 = Enables the TMR1 overflow interrupt 0 = Disables the TMR1 overflow interrupt DS39760D-page 92 x = Bit is unknown © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 8-7: PIE2: PERIPHERAL INTERRUPT ENABLE REGISTER 2 R/W-0 U-0 R/W-0 U-0 U-0 R/W-0 U-0 U-0 OSCFIE — USBIE — — HLVDIE — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 OSCFIE: Oscillator Fail Interrupt Enable bit 1 = Enabled 0 = Disabled bit 6 Unimplemented: Read as ‘0’ bit 5 USBIE: USB Interrupt Enable bit 1 = Enabled 0 = Disabled bit 4-3 Unimplemented: Read as ‘0’ bit 2 HLVDIE: High/Low-Voltage Detect Interrupt Enable bit 1 = Enabled 0 = Disabled bit 1-0 Unimplemented: Read as ‘0’ © 2008 Microchip Technology Inc. x = Bit is unknown DS39760D-page 93 PIC18F2450/4450 8.5 IPR Registers The IPR registers contain the individual priority bits for the peripheral interrupts. Due to the number of peripheral interrupt sources, there are two Peripheral Interrupt Priority registers (IPR1 and IPR2). Using the priority bits requires that the Interrupt Priority Enable (IPEN) bit be set. REGISTER 8-8: IPR1: PERIPHERAL INTERRUPT PRIORITY REGISTER 1 U-0 R/W-1 R/W-1 R/W-1 U-0 R/W-1 R/W-1 R/W-1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 Unimplemented: Read as ‘0’ bit 6 ADIP: A/D Converter Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 RCIP: EUSART Receive Interrupt Priority bit 1 = High priority 0 = Low priority bit 4 TXIP: EUSART Transmit Interrupt Priority bit x = Bit is unknown 1 = High priority 0 = Low priority bit 3 Unimplemented: Read as ‘0’ bit 2 CCP1IP: CCP1 Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 TMR2IP: TMR2 to PR2 Match Interrupt Priority bit 1 = High priority 0 = Low priority bit 0 TMR1IP: TMR1 Overflow Interrupt Priority bit 1 = High priority 0 = Low priority DS39760D-page 94 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 8-9: IPR2: PERIPHERAL INTERRUPT PRIORITY REGISTER 2 R/W-1 U-0 R/W-1 U-0 U-0 R/W-1 U-0 U-0 OSCFIP — USBIP — — HLVDIP — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 OSCFIP: Oscillator Fail Interrupt Priority bit 1 = High priority 0 = Low priority bit 6 Unimplemented: Read as ‘0’ bit 5 USBIP: USB Interrupt Priority bit 1 = High priority 0 = Low priority bit 4-3 Unimplemented: Read as ‘0’ bit 2 HLVDIP: High/Low-Voltage Detect Interrupt Priority bit 1 = High priority 0 = Low priority bit 1-0 Unimplemented: Read as ‘0’ © 2008 Microchip Technology Inc. x = Bit is unknown DS39760D-page 95 PIC18F2450/4450 8.6 RCON Register The RCON register contains flag bits which are used to determine the cause of the last Reset or wake-up from Idle or Sleep modes. RCON also contains the IPEN bit which enables interrupt priorities. REGISTER 8-10: RCON: RESET CONTROL REGISTER R/W-0 R/W-1(1) U-0 R/W-1 R-1 R-1 R/W-0(2) R/W-0 IPEN SBOREN — RI TO PD POR BOR bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 IPEN: Interrupt Priority Enable bit 1 = Enable priority levels on interrupts 0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode) bit 6 SBOREN: BOR Software Enable bit(1) For details of bit operation, see Register 4-1. bit 5 Unimplemented: Read as ‘0’ bit 4 RI: RESET Instruction Flag bit For details of bit operation, see Register 4-1. bit 3 TO: Watchdog Time-out Flag bit For details of bit operation, see Register 4-1. bit 2 PD: Power-Down Detection Flag bit For details of bit operation, see Register 4-1. bit 1 POR: Power-on Reset Status bit(2) For details of bit operation, see Register 4-1. bit 0 BOR: Brown-out Reset Status bit For details of bit operation, see Register 4-1. Note 1: 2: If SBOREN is enabled, its Reset state is ‘1’; otherwise, it is ‘0’. See Register 4-1 for additional information. The actual Reset value of POR is determined by the type of device Reset. See Register 4-1 for additional information. DS39760D-page 96 © 2008 Microchip Technology Inc. PIC18F2450/4450 8.7 INTx Pin Interrupts 8.8 TMR0 Interrupt External interrupts on the RB0/AN12/INT0, RB1/AN10/ INT1and RB2/AN8/INT2/VMO pins are edge-triggered. If the corresponding INTEDGx bit in the INTCON2 register is set (= 1), the interrupt is triggered by a rising edge; if the bit is clear, the trigger is on the falling edge. When a valid edge appears on the RBx/INTx pin, the corresponding flag bit, INTxIF, is set. This interrupt can be disabled by clearing the corresponding enable bit, INTxIE. Flag bit, INTxIF, must be cleared in software in the Interrupt Service Routine before re-enabling the interrupt. In 8-bit mode (which is the default), an overflow in the TMR0 register (FFh → 00h) will set flag bit, TMR0IF. In 16-bit mode, an overflow in the TMR0H:TMR0L register pair (FFFFh → 0000h) will set TMR0IF. The interrupt can be enabled/disabled by setting/clearing enable bit, TMR0IE (INTCON<5>). Interrupt priority for Timer0 is determined by the value contained in the interrupt priority bit, TMR0IP (INTCON2<2>). See Section 12.0 “Timer2 Module” for further details on the Timer0 module. All external interrupts (INT0, INT1 and INT2) can wakeup the processor from the power-managed modes if bit, INTxIE, was set prior to going into the power-managed modes. If the Global Interrupt Enable bit, GIE, is set, the processor will branch to the interrupt vector following wake-up. 8.9 Interrupt priority for INT1 and INT2 is determined by the value contained in the interrupt priority bits, INT1IP (INTCON3<6>) and INT2IP (INTCON3<7>). There is no priority bit associated with INT0. It is always a high-priority interrupt source. EXAMPLE 8-1: MOVWF MOVFF MOVFF ; ; USER ; MOVFF MOVF MOVFF PORTB Interrupt-on-Change An input change on PORTB<7:4> sets flag bit, RBIF (INTCON<0>). The interrupt can be enabled/disabled by setting/clearing enable bit, RBIE (INTCON<3>). Interrupt priority for PORTB interrupt-on-change is determined by the value contained in the interrupt priority bit, RBIP (INTCON2<0>). 8.10 Context Saving During Interrupts During interrupts, the return PC address is saved on the stack. Additionally, the WREG, STATUS and BSR registers are saved on the Fast Return Stack. If a fast return from interrupt is not used (see Section 5.3 “Data Memory Organization”), the user may need to save the WREG, STATUS and BSR registers on entry to the Interrupt Service Routine. Depending on the user’s application, other registers may also need to be saved. Example 8-1 saves and restores the WREG, STATUS and BSR registers during an Interrupt Service Routine. SAVING STATUS, WREG AND BSR REGISTERS IN RAM W_TEMP STATUS, STATUS_TEMP BSR, BSR_TEMP ; W_TEMP is in virtual bank ; STATUS_TEMP located anywhere ; BSR_TMEP located anywhere ISR CODE BSR_TEMP, BSR W_TEMP, W STATUS_TEMP, STATUS © 2008 Microchip Technology Inc. ; Restore BSR ; Restore WREG ; Restore STATUS DS39760D-page 97 PIC18F2450/4450 NOTES: DS39760D-page 98 © 2008 Microchip Technology Inc. PIC18F2450/4450 9.0 I/O PORTS Depending on the device selected and features enabled, there are up to five ports available. Some pins of the I/O ports are multiplexed with an alternate function from the peripheral features on the device. In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin. Each port has three registers for its operation. These registers are: • TRIS register (Data Direction register) • PORT register (reads the levels on the pins of the device) • LAT register (Output Latch register) The Output Latch register (LATA) is useful for readmodify-write operations on the value driven by the I/O pins. A simplified model of a generic I/O port, without the interfaces to other peripherals, is shown in Figure 9-1. FIGURE 9-1: GENERIC I/O PORT OPERATION D WR LAT or PORT Q I/O pin(1) CK The RA4 pin is multiplexed with the Timer0 module clock input to become the RA4/T0CKI pin. The RA6 pin is multiplexed with the main oscillator pin; it is enabled as an oscillator or I/O pin by the selection of the main oscillator in Configuration Register 1H (see Section 18.1 “Configuration Bits” for details). When not used as a port pin, RA6 and its associated TRIS and LAT bits are read as ‘0’. RA4 is also multiplexed with the USB module; it serves as a receiver input from an external USB transceiver. For details on configuration of the USB module, see Section 14.2 “USB Status and Control”. Several PORTA pins are multiplexed with analog inputs. The operation of pins RA5 and RA3:RA0 as A/D Converter inputs is selected by clearing/setting the control bits in the ADCON1 register (A/D Control Register 1). D Q All other PORTA pins have TTL input levels and full CMOS output drivers. CK TRIS Latch Input Buffer EXAMPLE 9-1: CLRF RD TRIS CLRF Q D ENEN RD PORT Note 1: MOVLW MOVWF MOVLW I/O pins have diode protection to VDD and VSS. MOVWF 9.1 On a Power-on Reset, RA5 and RA3:RA0 are configured as analog inputs and read as ‘0’. RA4 is configured as a digital input. The TRISA register controls the direction of the RA pins, even when they are being used as analog inputs. The user must ensure the bits in the TRISA register are maintained set when using them as analog inputs. Data Latch WR TRIS The Output Latch register (LATA) is also memory mapped. Read-modify-write operations on the LATA register read and write the latched output value for PORTA. Note: RD LAT Data Bus Reading the PORTA register reads the status of the pins; writing to it will write to the port latch. PORTA, TRISA and LATA Registers PORTA ; ; ; LATA ; ; ; 0Fh ; ADCON1 ; 0CFh ; ; ; TRISA ; ; INITIALIZING PORTA Initialize PORTA by clearing output data latches Alternate method to clear output data latches Configure A/D for digital inputs Value used to initialize data direction Set RA<3:0> as inputs RA<5:4> as outputs PORTA is an 8-bit wide, bidirectional port. The corresponding Data Direction register is TRISA. Setting a TRISA bit (= 1) will make the corresponding PORTA pin an input (i.e., put the corresponding output driver in a high-impedance mode). Clearing a TRISA bit (= 0) will make the corresponding PORTA pin an output (i.e., put the contents of the output latch on the selected pin). © 2008 Microchip Technology Inc. DS39760D-page 99 PIC18F2450/4450 TABLE 9-1: Pin PORTA I/O SUMMARY Function TRIS Setting I/O RA0 0 OUT DIG 1 IN TTL PORTA<0> data input; disabled when analog input enabled. AN0 1 IN ANA A/D input channel 0. Default configuration on POR; does not affect digital output. RA1 0 OUT DIG LATA<1> data output; not affected by analog input. 1 IN TTL PORTA<1> data input; reads ‘0’ on POR. AN1 1 IN ANA A/D input channel 1. Default configuration on POR; does not affect digital output. RA2 0 OUT DIG LATA<2> data output; not affected by analog input. 1 IN TTL PORTA<2> data input. Disabled when analog functions enabled. AN2 1 IN ANA A/D input channel 2. Default configuration on POR; not affected by analog output. VREF- 1 IN ANA A/D voltage reference low input. RA3 0 OUT DIG LATA<3> data output; not affected by analog input. 1 IN TTL PORTA<3> data input; disabled when analog input enabled. AN3 1 IN ANA A/D input channel 3. Default configuration on POR. VREF+ 1 IN ANA A/D voltage reference high input. RA4 0 OUT DIG LATA<4> data output; not affected by analog input. 1 IN ST PORTA<4> data input; disabled when analog input enabled. T0CKI 1 IN ST Timer0 clock input. RCV x IN TTL External USB transceiver RCV input. RA5 0 OUT DIG LATA<5> data output; not affected by analog input. 1 IN TTL PORTA<5> data input; disabled when analog input enabled. AN4 1 IN ANA A/D input channel 4. Default configuration on POR. HLVDIN 1 IN ANA High/Low-Voltage Detect external trip point input. OSC2 x OUT ANA Main oscillator feedback output connection (all XT and HS modes). CLKO x OUT DIG System cycle clock output (FOSC/4); available in EC, ECPLL and INTCKO modes. RA6 0 OUT DIG LATA<6> data output. Available only in ECIO, ECPIO and INTIO modes; otherwise, reads as ‘0’. 1 IN TTL PORTA<6> data input. Available only in ECIO, ECPIO and INTIO modes; otherwise, reads as ‘0’. RA0/AN0 RA1/AN1 RA2/AN2/ VREF- RA3/AN3/ VREF+ RA4/T0CKI/ RCV RA5/AN4/ HLVDIN OSC2/CLKO/ RA6 Legend: I/O Type Description LATA<0> data output; not affected by analog input. OUT = Output, IN = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Buffer Input, TTL = TTL Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option) TABLE 9-2: SUMMARY OF REGISTERS ASSOCIATED WITH PORTA Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: — RA6(1) RA5 RA4 RA3 RA2 RA1 RA0 51 LATA — LATA6(1) LATA5 LATA4 LATA3 LATA2 LATA1 LATA0 51 TRISA — TRISA6(1) TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 51 ADCON1 — — VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 50 UCON — PPBRST SE0 PKTDIS USBEN — 52 Name PORTA RESUME SUSPND Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PORTA. Note 1: RA6 and its associated latch and data direction bits are enabled as I/O pins based on oscillator configuration; otherwise, they are read as ‘0’. DS39760D-page 100 © 2008 Microchip Technology Inc. PIC18F2450/4450 9.2 PORTB, TRISB and LATB Registers PORTB is an 8-bit wide, bidirectional port. The corresponding Data Direction register is TRISB. Setting a TRISB bit (= 1) will make the corresponding PORTB pin an input (i.e., put the corresponding output driver in a high-impedance mode). Clearing a TRISB bit (= 0) will make the corresponding PORTB pin an output (i.e., put the contents of the output latch on the selected pin). The Output Latch register (LATB) is also memory mapped. Read-modify-write operations on the LATB register read and write the latched output value for PORTB. Each of the PORTB pins has a weak internal pull-up. A single control bit can turn on all the pull-ups. This is performed by clearing bit, RBPU (INTCON2<7>). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on a Power-on Reset. Note: On a Power-on Reset, RB4:RB0 are configured as analog inputs by default and read as ‘0’; RB7:RB5 are configured as digital inputs. By programming the Configuration bit, PBADEN (CONFIG3H<1>), RB4:RB0 will alternatively be configured as digital inputs on POR. Four of the PORTB pins (RB7:RB4) have an interrupton-change feature. Only pins configured as inputs can cause this interrupt to occur. Any RB7:RB4 pin configured as an output is excluded from the interrupton-change comparison. The pins are compared with the old value latched on the last read of PORTB. The “mismatch” outputs of RB7:RB4 are ORed together to generate the RB Port Change Interrupt with Flag bit, RBIF (INTCON<0>). A mismatch condition will continue to set flag bit, RBIF. Reading PORTB will end the mismatch condition and allow flag bit, RBIF, to be cleared. The interrupt-on-change feature is recommended for wake-up on key depression operation and operations where PORTB is only used for the interrupt-on-change feature. Polling of PORTB is not recommended while using the interrupt-on-change feature. Pins, RB2 and RB3, are multiplexed with the USB peripheral and serve as the differential signal outputs for an external USB transceiver (TRIS configuration). Refer to Section 14.2.2.2 “External Transceiver” for additional information on configuring the USB module for operation with an external transceiver. EXAMPLE 9-2: CLRF CLRF MOVLW MOVWF MOVLW MOVWF PORTB ; ; ; LATB ; ; ; 0Eh ; ADCON1 ; ; ; 0CFh ; ; ; TRISB ; ; ; INITIALIZING PORTB Initialize PORTB by clearing output data latches Alternate method to clear output data latches Set RB<4:0> as digital I/O pins (required if config bit PBADEN is set) Value used to initialize data direction Set RB<3:0> as inputs RB<5:4> as outputs RB<7:6> as inputs The interrupt-on-change can be used to wake the device from Sleep. The user, in the Interrupt Service Routine, can clear the interrupt in the following manner: a) b) c) Any read or write of PORTB (except with the MOVFF (ANY), PORTB instruction). This will end the mismatch condition. Wait one or more instruction cycles. Clear flag bit, RBIF. © 2008 Microchip Technology Inc. DS39760D-page 101 PIC18F2450/4450 TABLE 9-3: Pin RB0/AN12/ INT0 PORTB I/O SUMMARY Function TRIS Setting I/O I/O Type RB0 0 OUT DIG LATB<0> data output; not affected by analog input. 1 IN TTL PORTB<0> data input; weak pull-up when RBPU bit is cleared. Disabled when analog input enabled.(1) 1 IN ANA A/D input channel 12.(1) AN12 RB1/AN10/ INT1 INT0 1 IN ST External interrupt 0 input. RB1 0 OUT DIG LATB<1> data output; not affected by analog input. 1 IN TTL PORTB<1> data input; weak pull-up when RBPU bit is cleared. Disabled when analog input enabled.(1) 1 IN ANA A/D input channel 10.(1) AN10 RB2/AN8/ INT2/VMO RB3/AN9/VPO RB4/AN11/ KBI0 INT1 1 IN ST External interrupt 1 input. RB2 0 OUT DIG LATB<2> data output; not affected by analog input. 1 IN TTL PORTB<2> data input; weak pull-up when RBPU bit is cleared. Disabled when analog input enabled.(1) AN8 1 IN ANA A/D input channel 8.(1) INT2 1 IN ST External interrupt 2 input. VMO 0 OUT DIG External USB transceiver VMO data output. RB3 0 OUT DIG LATB<3> data output; not affected by analog input. 1 IN TTL PORTB<3> data input; weak pull-up when RBPU bit is cleared. Disabled when analog input enabled.(1) AN9 1 IN ANA A/D input channel 9.(1) VPO 0 OUT DIG External USB transceiver VPO data output. RB4 0 OUT DIG LATB<4> data output; not affected by analog input. 1 IN TTL PORTB<4> data input; weak pull-up when RBPU bit is cleared. Disabled when analog input enabled.(1) 1 IN ANA A/D input channel 11.(1) AN11 RB5/KBI1/ PGM RB6/KBI2/ PGC RB7/KBI3/ PGD Legend: Note 1: 2: Description KBI0 1 IN TTL Interrupt-on-pin change. RB5 0 OUT DIG LATB<5> data output. 1 IN TTL PORTB<5> data input; weak pull-up when RBPU bit is cleared. KBI1 1 IN TTL Interrupt-on-pin change. PGM x IN ST Single-Supply Programming mode entry (ICSP™). Enabled by LVP Configuration bit; all other pin functions disabled. RB6 0 OUT DIG LATB<6> data output. 1 IN TTL PORTB<6> data input; weak pull-up when RBPU bit is cleared. KBI2 1 IN TTL Interrupt-on-pin change. PGC x IN ST Serial execution (ICSP) clock input for ICSP and ICD operation.(2) RB7 0 OUT DIG LATB<7> data output. 1 IN TTL PORTB<7> data input; weak pull-up when RBPU bit is cleared. KBI3 1 IN TTL Interrupt-on-pin change. PGD x OUT DIG Serial execution data output for ICSP and ICD operation.(2) x IN ST Serial execution data input for ICSP and ICD operation.(2) OUT = Output, IN = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Buffer Input, TTL = TTL Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option) Configuration on POR is determined by PBADEN Configuration bit. Pins are configured as analog inputs when PBADEN is set and digital inputs when PBADEN is cleared. All other pin functions are disabled when ICSP™ or ICD operation is enabled. DS39760D-page 102 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 9-4: Name PORTB SUMMARY OF REGISTERS ASSOCIATED WITH PORTB Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 51 LATB LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 51 TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 51 TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 — TMR0IP — RBIP 49 INTCON GIE/GIEH PEIE/GIEL INTCON2 RBPU INTEDG0 INTEDG1 INTEDG2 INTCON3 INT2IP INT1IP — INT2IE INT1IE — INT2IF INT1IF 49 ADCON1 — — VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 50 UCON — PPBRST SE0 PKTDIS USBEN — 52 RESUME SUSPND Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PORTB. © 2008 Microchip Technology Inc. DS39760D-page 103 PIC18F2450/4450 9.3 PORTC, TRISC and LATC Registers PORTC is a 7-bit wide, bidirectional port. The corresponding Data Direction register is TRISC. Setting a TRISC bit (= 1) will make the corresponding PORTC pin an input (i.e., put the corresponding output driver in a high-impedance mode). Clearing a TRISC bit (= 0) will make the corresponding PORTC pin an output (i.e., put the contents of the output latch on the selected pin). When enabling peripheral functions on PORTC pins other than RC4 and RC5, care should be taken in defining the TRIS bits. Some peripherals override the TRIS bit to make a pin an output, while other peripherals override the TRIS bit to make a pin an input. The user should refer to the corresponding peripheral section for the correct TRIS bit settings. Note: In PIC18F2450/4450 devices, the RC3 pin is not implemented. The Output Latch register (LATC) is also memory mapped. Read-modify-write operations on the LATC register read and write the latched output value for PORTC. PORTC is primarily multiplexed with serial communication modules, including the EUSART and the USB module (Table 9-5). Except for RC4 and RC5, PORTC uses Schmitt Trigger input buffers. Pins RC4 and RC5 are multiplexed with the USB module. Depending on the configuration of the module, they can serve as the differential data lines for the onchip USB transceiver, or the data inputs from an external USB transceiver. Both RC4 and RC5 have TTL input buffers instead of the Schmitt Trigger buffers on the other pins. Unlike other PORTC pins, RC4 and RC5 do not have TRISC bits associated with them. As digital ports, they can only function as digital inputs. When configured for USB operation, the data direction is determined by the configuration and status of the USB module at a given time. If an external transceiver is used, RC4 and RC5 always function as inputs from the transceiver. If the on-chip transceiver is used, the data direction is determined by the operation being performed by the module at that time. On a Power-on Reset, these pins, except RC4 and RC5, are configured as digital inputs. To use pins RC4 and RC5 as digital inputs, the USB module must be disabled (UCON<3> = 0) and the on-chip USB transceiver must be disabled (UCFG<3> = 1). The contents of the TRISC register are affected by peripheral overrides. Reading TRISC always returns the current contents, even though a peripheral device may be overriding one or more of the pins. EXAMPLE 9-3: CLRF PORTC CLRF LATC MOVLW 07h MOVWF TRISC INITIALIZING PORTC ; ; ; ; ; ; ; ; ; ; ; Initialize PORTC by clearing output data latches Alternate method to clear output data latches Value used to initialize data direction RC<5:0> as outputs RC<7:6> as inputs When the external transceiver is enabled, RC2 also serves as the output enable control to the transceiver. Additional information on configuring USB options is provided in Section 14.2.2.2 “External Transceiver”. DS39760D-page 104 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 9-5: Pin RC0/T1OSO/ T1CKI PORTC I/O SUMMARY Function TRIS Setting I/O I/O Type RC0 0 OUT DIG T1OSO RC1/T1OSI/ UOE RC2/CCP1 IN ST x OUT ANA RC6/TX/CK RC7/RX/DT Legend: Note 1: PORTC<0> data input. Timer1 oscillator output; enabled when Timer1 oscillator enabled. Disables digital I/O. 1 IN ST RC1 0 OUT DIG LATC<1> data output. 1 IN ST PORTC<1> data input. T1OSI x IN ANA Timer1 oscillator input; enabled when Timer1 oscillator enabled. Disables digital I/O. UOE 0 OUT DIG External USB transceiver OE output. RC2 0 OUT DIG LATC<2> data output. 1 IN ST PORTC<2> data input. 0 OUT DIG CCP1 Compare and PWM output; takes priority over port data. 1 IN ST CCP1 Capture input. RC4 —(1) IN TTL PORTC<4> data input; disabled when USB module or on-chip transceiver is enabled. D- —(1) Timer1 counter input. OUT XCVR (1) IN XCVR VM —(1) IN TTL External USB transceiver VM input. RC5 —(1) IN TTL PORTC<5> data input; disabled when USB module or on-chip transceiver is enabled. D+ —(1) OUT XCVR —(1) IN XCVR VP —(1) IN TTL RC6 0 OUT DIG LATC<6> data output. 1 IN ST PORTC<6> data input. TX 0 OUT DIG Asynchronous serial transmit data output (EUSART module); takes priority over port data. User must configure as output. CK 0 OUT DIG Synchronous serial clock output (EUSART module); takes priority over port data. Synchronous serial clock input (EUSART module). — RC5/D+/VP LATC<0> data output. T1CKI CCP1 RC4/D-/VM 1 Description USB bus differential minus line output (internal transceiver). USB bus differential minus line input (internal transceiver). USB bus differential plus line output (internal transceiver). USB bus differential plus line input (internal transceiver). External USB transceiver VP input. 1 IN ST 0 OUT DIG LATC<7> data output. 1 IN ST PORTC<7> data input. RX 1 IN ST Asynchronous serial receive data input (EUSART module). DT 1 OUT DIG Synchronous serial data output (EUSART module). 1 IN ST Synchronous serial data input (EUSART module). User must configure as an input. RC7 OUT = Output, IN = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Buffer Input, TTL = TTL Buffer Input, XCVR = USB Transceiver, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option) RC4 and RC5 do not have corresponding TRISC bits. In Port mode, these pins are input only. USB data direction is determined by the USB configuration. © 2008 Microchip Technology Inc. DS39760D-page 105 PIC18F2450/4450 TABLE 9-6: Name PORTC SUMMARY OF REGISTERS ASSOCIATED WITH PORTC Reset Values on Page: RC1 RC0 51 LATC1 LATC0 51 TRISC0 51 — 52 Bit 6 Bit 5 Bit 4 Bit 3 RC7 RC6 RC5(1) RC4(1) — RC2 — — LATC2 TRISC2 TRISC1 LATC LATC7 LATC6 — TRISC TRISC7 TRISC6 — — — UCON — PPBRST SE0 PKTDIS USBEN Bit 2 Bit 0 Bit 7 Bit 1 RESUME SUSPND Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PORTC. Note 1: RC5 and RC4 are only available as port pins when the USB module is disabled (UCON<3> = 0). DS39760D-page 106 © 2008 Microchip Technology Inc. PIC18F2450/4450 9.4 Note: PORTD, TRISD and LATD Registers PORTD is only available on 40/44-pin devices. PORTD is an 8-bit wide, bidirectional port. The corresponding Data Direction register is TRISD. Setting a TRISD bit (= 1) will make the corresponding PORTD pin an input (i.e., put the corresponding output driver in a high-impedance mode). Clearing a TRISD bit (= 0) will make the corresponding PORTD pin an output (i.e., put the contents of the output latch on the selected pin). EXAMPLE 9-4: CLRF PORTD CLRF LATD MOVLW 0CFh MOVWF TRISD INITIALIZING PORTD ; ; ; ; ; ; ; ; ; ; ; ; Initialize PORTD by clearing output data latches Alternate method to clear output data latches Value used to initialize data direction Set RD<3:0> as inputs RD<5:4> as outputs RD<7:6> as inputs The Output Latch register (LATD) is also memory mapped. Read-modify-write operations on the LATD register read and write the latched output value for PORTD. All pins on PORTD are implemented with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. Note: On a Power-on Reset, these pins are configured as digital inputs. © 2008 Microchip Technology Inc. DS39760D-page 107 PIC18F2450/4450 TABLE 9-7: Pin PORTD I/O SUMMARY Function TRIS Setting I/O I/O Type RD0 0 OUT DIG 1 IN ST PORTD<0> data input. 0 OUT DIG LATD<1> data output. 1 IN ST PORTD<1> data input. 0 OUT DIG LATD<2> data output. 1 IN ST PORTD<2> data input. 0 OUT DIG LATD<3> data output. 1 IN ST PORTD<3> data input. 0 OUT DIG LATD<4> data output. 1 IN ST PORTD<4> data input. 0 OUT DIG LATD<5> data output 1 IN ST PORTD<5> data input 0 OUT DIG LATD<6> data output. 1 IN ST PORTD<6> data input. 0 OUT DIG LATD<7> data output. 1 IN ST PORTD<7> data input. RD0 RD1 RD1 RD2 RD2 RD3 RD3 RD4 RD4 RD5 RD5 RD6 RD6 RD7 Legend: RD7 PORTD(1) LATD<0> data output. OUT = Output, IN = Input, DIG = Digital Output, ST = Schmitt Buffer Input TABLE 9-8: Name Description SUMMARY OF REGISTERS ASSOCIATED WITH PORTD Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 51 LATD(1) LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0 51 TRISD(1) TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 51 Note 1: These registers and/or bits are unimplemented on 28-pin devices. DS39760D-page 108 © 2008 Microchip Technology Inc. PIC18F2450/4450 9.5 PORTE, TRISE and LATE Registers Depending on the particular PIC18F2450/4450 device selected, PORTE is implemented in two different ways. For 40/44-pin devices, PORTE is a 4-bit wide port. Three pins (RE0/AN5, RE1/AN6 and RE2/AN7) are individually configurable as inputs or outputs. These pins have Schmitt Trigger input buffers. When selected as an analog input, these pins will read as ‘0’s. The corresponding Data Direction register is TRISE. Setting a TRISE bit (= 1) will make the corresponding PORTE pin an input (i.e., put the corresponding output driver in a high-impedance mode). Clearing a TRISE bit (= 0) will make the corresponding PORTE pin an output (i.e., put the contents of the output latch on the selected pin). TRISE controls the direction of the RE pins, even when they are being used as analog inputs. The user must make sure to keep the pins configured as inputs when using them as analog inputs. Note: functions as a digital input only pin; as such, it does not have TRIS or LAT bits associated with its operation. Otherwise, it functions as the device’s Master Clear input. In either configuration, RE3 also functions as the programming voltage input during programming. Note: EXAMPLE 9-5: CLRF CLRF MOVLW MOVWF MOVLW MOVWF On a Power-on Reset, RE2:RE0 are configured as analog inputs. The Output Latch register (LATE) is also memory mapped. Read-modify-write operations on the LATE register read and write the latched output value for PORTE. The fourth pin of PORTE (MCLR/VPP/RE3) is an input only pin. Its operation is controlled by the MCLRE Configuration bit. When selected as a port pin (MCLRE = 0), it REGISTER 9-1: U-0 9.5.1 PORTE ; ; ; LATE ; ; ; 0Ah ; ADCON1 ; 03h ; ; ; TRISC ; ; ; INITIALIZING PORTE Initialize PORTE by clearing output data latches Alternate method to clear output data latches Configure A/D for digital inputs Value used to initialize data direction Set RE<0> as inputs RE<1> as inputs RE<2> as outputs PORTE IN 28-PIN DEVICES For 28-pin devices, PORTE is only available when Master Clear functionality is disabled (MCLRE = 0). In these cases, PORTE is a single bit, input only port comprised of RE3 only. The pin operates as previously described. PORTE REGISTER U-0 — On a Power-on Reset, RE3 is enabled as a digital input only if Master Clear functionality is disabled. — U-0 — U-0 — R/W-x (1,2) RE3 R/W-0 R/W-0 R/W-0 RE2(3) RE1(3) RE0(3) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-4 Unimplemented: Read as ‘0’ bit 3-0 RE3:RE0: PORTE Data Input bits(1,2,3) Note 1: 2: 3: x = Bit is unknown implemented only when Master Clear functionality is disabled (MCLRE Configuration bit = 0); otherwise, read as ‘0’. RE3 is the only PORTE bit implemented on both 28-pin and 40/44-pin devices. All other bits are implemented only when PORTE is implemented (i.e., 40/44-pin devices). Unimplemented in 28-pin devices; read as ‘0’. © 2008 Microchip Technology Inc. DS39760D-page 109 PIC18F2450/4450 TABLE 9-9: Pin PORTE I/O SUMMARY Function TRIS Setting I/O I/O Type RE0 0 OUT DIG 1 IN ST AN5 1 IN ANA A/D input channel 5; default configuration on POR. RE1 0 OUT DIG LATE<1> data output; not affected by analog input. 1 IN ST AN6 1 IN ANA A/D input channel 6; default configuration on POR. RE2 0 OUT DIG LATE<2> data output; not affected by analog input. 1 IN ST PORTE<2> data input; disabled when analog input enabled. RE0/AN5 RE1/AN6 RE2/AN7 MCLR/VPP/ RE3 Legend: Note 1: LATE<0> data output; not affected by analog input. PORTE<0> data input; disabled when analog input enabled. PORTE<1> data input; disabled when analog input enabled. AN7 1 IN ANA MCLR —(1) IN ST A/D input channel 7; default configuration on POR. VPP — (1) IN ANA High-voltage detection, used for ICSP™ mode entry detection. Always available regardless of pin mode. RE3 — (1) IN ST PORTE<3> data input; enabled when MCLRE Configuration bit is clear. External Master Clear input; enabled when MCLRE Configuration bit is set. OUT = Output, IN = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Buffer Input. RE3 does not have a corresponding TRISE<3> bit. This pin is always an input regardless of mode. TABLE 9-10: Name Description SUMMARY OF REGISTERS ASSOCIATED WITH PORTE Reset Values on Page: Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PORTE — — — — RE3(1,2) RE2(3) RE1(3) RE0(3) 51 (3) LATE — — — — — LATE2 LATE1 LATE0 51 TRISE(3) — — — — — TRISE2 TRISE1 TRISE0 51 ADCON1 — — VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 50 Legend: — = unimplemented, read as ‘0’ Note 1: Implemented only when Master Clear functionality is disabled (MCLRE Configuration bit = 0); otherwise, read as ‘0’. 2: RE3 is the only PORTE bit implemented on both 28-pin and 40/44-pin devices. All other bits are implemented only when PORTE is implemented (i.e., 40/44-pin devices). 3: These registers and/or bits are unimplemented on 28-pin devices. DS39760D-page 110 © 2008 Microchip Technology Inc. PIC18F2450/4450 10.0 TIMER0 MODULE The T0CON register (Register 10-1) controls all aspects of the module’s operation, including the prescale selection. It is both readable and writable. The Timer0 module incorporates the following features: • Software selectable operation as a timer or counter in both 8-bit or 16-bit modes • Readable and writable registers • Dedicated 8-bit, software programmable prescaler • Selectable clock source (internal or external) • Edge select for external clock • Interrupt on overflow REGISTER 10-1: A simplified block diagram of the Timer0 module in 8-bit mode is shown in Figure 10-1. Figure 10-2 shows a simplified block diagram of the Timer0 module in 16-bit mode. T0CON: TIMER0 CONTROL REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 TMR0ON T08BIT T0CS T0SE PSA T0PS2 T0PS1 T0PS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 TMR0ON: Timer0 On/Off Control bit 1 = Enables Timer0 0 = Stops Timer0 bit 6 T08BIT: Timer0 8-Bit/16-Bit Control bit 1 = Timer0 is configured as an 8-bit timer/counter 0 = Timer0 is configured as a 16-bit timer/counter bit 5 T0CS: Timer0 Clock Source Select bit 1 = Transition on T0CKI pin 0 = Internal instruction cycle clock (CLKO) bit 4 T0SE: Timer0 Source Edge Select bit 1 = Increment on high-to-low transition on T0CKI pin 0 = Increment on low-to-high transition on T0CKI pin bit 3 PSA: Timer0 Prescaler Assignment bit 1 = TImer0 prescaler is not assigned. Timer0 clock input bypasses prescaler. 0 = Timer0 prescaler is assigned. Timer0 clock input comes from prescaler output. bit 2-0 T0PS2:T0PS0: Timer0 Prescaler Select bits 111 = 1:256 Prescale value 110 = 1:128 Prescale value 101 = 1:64 Prescale value 100 = 1:32 Prescale value 011 = 1:16 Prescale value 010 = 1:8 Prescale value 001 = 1:4 Prescale value 000 = 1:2 Prescale value © 2008 Microchip Technology Inc. DS39760D-page 111 PIC18F2450/4450 10.1 Timer0 Operation Timer0 can operate as either a timer or a counter; the mode is selected by clearing the T0CS bit (T0CON<5>). In Timer mode, the module increments on every clock by default unless a different prescaler value is selected (see Section 10.3 “Prescaler”). If the TMR0 register is written to, the increment is inhibited for the following two instruction cycles. The user can work around this by writing an adjusted value to the TMR0 register. The Counter mode is selected by setting the T0CS bit (= 1). In Counter mode, Timer0 increments either on every rising or falling edge of pin RA4/T0CKI. The incrementing edge is determined by the Timer0 Source Edge Select bit, T0SE (T0CON<4>); clearing this bit selects the rising edge. Restrictions on the external clock input are discussed below. An external clock source can be used to drive Timer0; however, it must meet certain requirements to ensure that the external clock can be synchronized with the FIGURE 10-1: internal phase clock (TOSC). There is a delay between synchronization and the onset of incrementing the timer/counter. 10.2 TMR0H is not the actual high byte of Timer0 in 16-bit mode; it is actually a buffered version of the real high byte of Timer0, which is not directly readable nor writable (refer to Figure 10-2). TMR0H is updated with the contents of the high byte of Timer0 during a read of TMR0L. This provides the ability to read all 16 bits of Timer0 without having to verify that the read of the high and low byte were valid, due to a rollover between successive reads of the high and low byte. Similarly, a write to the high byte of Timer0 must also take place through the TMR0H Buffer register. The high byte is updated with the contents of TMR0H when a write occurs to TMR0L. This allows all 16 bits of Timer0 to be updated at once. TIMER0 BLOCK DIAGRAM (8-BIT MODE) FOSC/4 0 1 1 Programmable Prescaler T0CKI pin T0SE T0CS 0 Sync with Internal Clocks Set TMR0IF on Overflow TMR0L (2 TCY Delay) 8 3 T0PS2:T0PS0 8 PSA Note: Timer0 Reads and Writes in 16-Bit Mode Internal Data Bus Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI maximum prescale. FIGURE 10-2: TIMER0 BLOCK DIAGRAM (16-BIT MODE) FOSC/4 0 1 1 T0CKI pin T0SE T0CS Programmable Prescaler 0 Sync with Internal Clocks TMR0 High Byte TMR0L 8 Set TMR0IF on Overflow (2 TCY Delay) 3 Read TMR0L T0PS2:T0PS0 Write TMR0L PSA 8 8 TMR0H 8 8 Internal Data Bus Note: Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI maximum prescale. DS39760D-page 112 © 2008 Microchip Technology Inc. PIC18F2450/4450 10.3 Prescaler 10.3.1 An 8-bit counter is available as a prescaler for the Timer0 module. The prescaler is not directly readable or writable; its value is set by the PSA and T0PS2:T0PS0 bits (T0CON<3:0>) which determine the prescaler assignment and prescale ratio. Clearing the PSA bit assigns the prescaler to the Timer0 module. When it is assigned, prescale values from 1:2 through 1:256, in power-of-2 increments, are selectable. When assigned to the Timer0 module, all instructions writing to the TMR0 register (e.g., CLRF TMR0, MOVWF TMR0, BSF TMR0,etc.) clear the prescaler count. Note: Writing to TMR0 when the prescaler is assigned to Timer0 will clear the prescaler count but will not change the prescaler assignment. TABLE 10-1: Name SWITCHING PRESCALER ASSIGNMENT The prescaler assignment is fully under software control and can be changed “on-the-fly” during program execution. 10.4 Timer0 Interrupt The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h in 8-bit mode, or from FFFFh to 0000h in 16-bit mode. This overflow sets the TMR0IF flag bit. The interrupt can be masked by clearing the TMR0IE bit (INTCON<5>). Before reenabling the interrupt, the TMR0IF bit must be cleared in software by the Interrupt Service Routine. Since Timer0 is shut down in Sleep mode, the TMR0 interrupt cannot awaken the processor from Sleep. REGISTERS ASSOCIATED WITH TIMER0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: TMR0L Timer0 Register Low Byte 50 TMR0H Timer0 Register High Byte INTCON GIE/GIEH PEIE/GIEL TMR0IE T0CON TMR0ON T08BIT T0CS T0SE PSA T0PS2 T0PS1 T0PS0 50 TRISA — TRISA6(1) TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 51 50 INT0IE RBIE TMR0IF INT0IF RBIF 49 Legend: — = unimplemented locations, read as ‘0’. Shaded cells are not used by Timer0. Note 1: RA6 is configured as a port pin based on various primary oscillator modes. When the port pin is disabled, all of the associated bits read ‘0’. © 2008 Microchip Technology Inc. DS39760D-page 113 PIC18F2450/4450 NOTES: DS39760D-page 114 © 2008 Microchip Technology Inc. PIC18F2450/4450 11.0 TIMER1 MODULE The Timer1 timer/counter module incorporates these features: • Software selectable operation as a 16-bit timer or counter • Readable and writable 8-bit registers (TMR1H and TMR1L) • Selectable clock source (internal or external) with device clock or Timer1 oscillator internal options • Interrupt on overflow • Module Reset on CCP Special Event Trigger • Device clock status flag (T1RUN) REGISTER 11-1: R/W-0 The module incorporates its own low-power oscillator to provide an additional clocking option. The Timer1 oscillator can also be used as a low-power clock source for the microcontroller in power-managed operation. Timer1 can also be used to provide Real-Time Clock (RTC) functionality to applications with only a minimal addition of external components and code overhead. Timer1 is controlled through the T1CON Control register (Register 11-1). It also contains the Timer1 Oscillator Enable bit (T1OSCEN). Timer1 can be enabled or disabled by setting or clearing control bit, TMR1ON (T1CON<0>). T1CON: TIMER1 CONTROL REGISTER R-0 RD16 A simplified block diagram of the Timer1 module is shown in Figure 11-1. A block diagram of the module’s operation in Read/Write mode is shown in Figure 11-2. T1RUN R/W-0 T1CKPS1 R/W-0 T1CKPS0 R/W-0 T1OSCEN R/W-0 R/W-0 R/W-0 T1SYNC TMR1CS TMR1ON bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 RD16: 16-Bit Read/Write Mode Enable bit 1 = Enables register read/write of Timer1 in one 16-bit operation 0 = Enables register read/write of Timer1 in two 8-bit operations bit 6 T1RUN: Timer1 System Clock Status bit 1 = Device clock is derived from Timer1 oscillator 0 = Device clock is derived from another source bit 5-4 T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value bit 3 T1OSCEN: Timer1 Oscillator Enable bit 1 = Timer1 oscillator is enabled 0 = Timer1 oscillator is shut off The oscillator inverter and feedback resistor are turned off to eliminate power drain. bit 2 T1SYNC: Timer1 External Clock Input Synchronization Select bit When TMR1CS = 1: 1 = Do not synchronize external clock input 0 = Synchronize external clock input When TMR1CS = 0: This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0. bit 1 TMR1CS: Timer1 Clock Source Select bit 1 = External clock from RC0/T1OSO/T1CKI pin (on the rising edge) 0 = Internal clock (FOSC/4) bit 0 TMR1ON: Timer1 On bit 1 = Enables Timer1 0 = Stops Timer1 © 2008 Microchip Technology Inc. DS39760D-page 115 PIC18F2450/4450 11.1 Timer1 Operation cycle (FOSC/4). When the bit is set, Timer1 increments on every rising edge of the Timer1 external clock input or the Timer1 oscillator, if enabled. Timer1 can operate in one of these modes: • Timer • Synchronous Counter • Asynchronous Counter When Timer1 is enabled, the RC1/T1OSI/UOE and RC0/T1OSO/T1CKI pins become inputs. This means the values of TRISC<1:0> are ignored and the pins are read as ‘0’. The operating mode is determined by the clock select bit, TMR1CS (T1CON<1>). When TMR1CS is cleared (= 0), Timer1 increments on every internal instruction FIGURE 11-1: TIMER1 BLOCK DIAGRAM Timer1 Oscillator On/Off T1OSO/T1CKI 1 FOSC/4 Internal Clock T1OSI 1 Synchronize Prescaler 1, 2, 4, 8 0 Detect 0 2 T1OSCEN(1) Sleep Input TMR1CS Timer1 On/Off T1CKPS1:T1CKPS0 T1SYNC TMR1ON Clear TMR1 (CCP Special Event Trigger) Set TMR1IF on Overflow TMR1 High Byte TMR1L Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain. FIGURE 11-2: TIMER1 BLOCK DIAGRAM (16-BIT READ/WRITE MODE) Timer1 Oscillator 1 T1OSO/T1CKI 1 FOSC/4 Internal Clock T1OSI Synchronize Prescaler 1, 2, 4, 8 0 Detect 0 2 Sleep Input (1) TMR1CS T1OSCEN T1CKPS1:T1CKPS0 T1SYNC Timer1 On/Off TMR1ON Clear TMR1 (CCP Special Event Trigger) TMR1 High Byte TMR1L 8 Set TMR1IF on Overflow Read TMR1L Write TMR1L 8 8 TMR1H 8 8 Internal Data Bus Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain. DS39760D-page 116 © 2008 Microchip Technology Inc. PIC18F2450/4450 11.2 Timer1 16-Bit Read/Write Mode Timer1 can be configured for 16-bit reads and writes (see Figure 11-2). When the RD16 control bit (T1CON<7>) is set, the address for TMR1H is mapped to a buffer register for the high byte of Timer1. A read from TMR1L will load the contents of the high byte of Timer1 into the Timer1 high byte buffer. This provides the user with the ability to accurately read all 16 bits of Timer1 without having to determine whether a read of the high byte, followed by a read of the low byte, has become invalid due to a rollover between reads. TABLE 11-1: Osc Type LP CAPACITOR SELECTION FOR THE TIMER OSCILLATOR(2,3,4) Freq 32 kHz C1 27 pF C2 (1) 27 pF(1) Note 1: Microchip suggests these values as a starting point in validating the oscillator circuit. 2: Higher capacitance increases the stability of the oscillator but also increases the start-up time. A write to the high byte of Timer1 must also take place through the TMR1H Buffer register. The Timer1 high byte is updated with the contents of TMR1H when a write occurs to TMR1L. This allows a user to write all 16 bits to both the high and low bytes of Timer1 at once. 3: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. The high byte of Timer1 is not directly readable or writable in this mode. All reads and writes must take place through the Timer1 High Byte Buffer register. Writes to TMR1H do not clear the Timer1 prescaler. The prescaler is only cleared on writes to TMR1L. 4: Capacitor values are for design guidance only. 11.3 Timer1 Oscillator An on-chip crystal oscillator circuit is incorporated between pins T1OSI (input) and T1OSO (amplifier output). It is enabled by setting the Timer1 Oscillator Enable bit, T1OSCEN (T1CON<3>). The oscillator is a low-power circuit rated for 32 kHz crystals. It will continue to run during all power-managed modes. The circuit for a typical LP oscillator is shown in Figure 11-3. Table 11-1 shows the capacitor selection for the Timer1 oscillator. The user must provide a software time delay to ensure proper start-up of the Timer1 oscillator. FIGURE 11-3: EXTERNAL COMPONENTS FOR THE TIMER1 LP OSCILLATOR C1 33 pF PIC18FXXXX T1OSI XTAL 32.768 kHz T1OSO C2 33 pF Note: See the Notes with Table 11-1 for additional information about capacitor selection. © 2008 Microchip Technology Inc. 11.3.1 USING TIMER1 AS A CLOCK SOURCE The Timer1 oscillator is also available as a clock source in power-managed modes. By setting the clock select bits, SCS1:SCS0 (OSCCON<1:0>), to ‘01’, the device switches to SEC_RUN mode. Both the CPU and peripherals are clocked from the Timer1 oscillator. If the IDLEN bit (OSCCON<7>) is cleared and a SLEEP instruction is executed, the device enters SEC_IDLE mode. Additional details are available in Section 3.0 “Power-Managed Modes”. Whenever the Timer1 oscillator is providing the clock source, the Timer1 system clock status flag, T1RUN (T1CON<6>), is set. This can be used to determine the controller’s current clocking mode. It can also indicate the clock source being currently used by the Fail-Safe Clock Monitor. If the Clock Monitor is enabled and the Timer1 oscillator fails while providing the clock, polling the T1RUN bit will indicate whether the clock is being provided by the Timer1 oscillator or another source. 11.3.2 LOW-POWER TIMER1 OPTION The Timer1 oscillator can operate at two distinct levels of power consumption based on device configuration. When the LPT1OSC Configuration bit is set, the Timer1 oscillator operates in a low-power mode. When LPT1OSC is not set, Timer1 operates at a higher power level. Power consumption for a particular mode is relatively constant, regardless of the device’s operating mode. The default Timer1 configuration is the higher power mode. As the Low-Power Timer1 mode tends to be more sensitive to interference, high noise environments may cause some oscillator instability. The low-power option is, therefore, best suited for low noise applications where power conservation is an important design consideration. DS39760D-page 117 PIC18F2450/4450 11.3.3 TIMER1 OSCILLATOR LAYOUT CONSIDERATIONS The Timer1 oscillator circuit draws very little power during operation. Due to the low-power nature of the oscillator, it may also be sensitive to rapidly changing signals in close proximity. The oscillator circuit, shown in Figure 11-3, should be located as close as possible to the microcontroller. There should be no circuits passing within the oscillator circuit boundaries other than VSS or VDD. If a high-speed circuit must be located near the oscillator (such as the CCP1 pin in Output Compare or PWM mode, or the primary oscillator using the OSC2 pin), a grounded guard ring around the oscillator circuit, as shown in Figure 11-4, may be helpful when used on a single-sided PCB or in addition to a ground plane. FIGURE 11-4: OSCILLATOR CIRCUIT WITH GROUNDED GUARD RING 11.5 If the CCP module is configured in Compare mode to generate a Special Event Trigger (CCP1M3:CCP1M0 = 1011), this signal will reset Timer1. The trigger from CCP1 will also start an A/D conversion if the A/D module is enabled (see Section 13.3.4 “Special Event Trigger” for more information). The module must be configured as either a timer or a synchronous counter to take advantage of this feature. When used this way, the CCPRH:CCPRL register pair effectively becomes a period register for Timer1. If Timer1 is running in Asynchronous Counter mode, this Reset operation may not work. In the event that a write to Timer1 coincides with a Special Event Trigger, the write operation will take precedence. Note: VDD VSS OSC1 OSC2 RC0 RC1 RC2 Note: Not drawn to scale. 11.4 Timer1 Interrupt The TMR1 register pair (TMR1H:TMR1L) increments from 0000h to FFFFh and rolls over to 0000h. The Timer1 interrupt, if enabled, is generated on overflow which is latched in interrupt flag bit, TMR1IF (PIR1<0>). This interrupt can be enabled or disabled by setting or clearing the Timer1 Interrupt Enable bit, TMR1IE (PIE1<0>). Resetting Timer1 Using the CCP Special Event Trigger 11.6 The Special Event Triggers from the CCP1 module will not set the TMR1IF interrupt flag bit (PIR1<0>). Using Timer1 as a Real-Time Clock Adding an external LP oscillator to Timer1 (such as the one described in Section 11.3 “Timer1 Oscillator”) gives users the option to include RTC functionality to their applications. This is accomplished with an inexpensive watch crystal to provide an accurate time base and several lines of application code to calculate the time. When operating in Sleep mode and using a battery or supercapacitor as a power source, it can completely eliminate the need for a separate RTC device and battery backup. The application code routine, RTCisr, shown in Example 11-1, demonstrates a simple method to increment a counter at one-second intervals using an Interrupt Service Routine. Incrementing the TMR1 register pair to overflow triggers the interrupt and calls the routine which increments the seconds counter by one. Additional counters for minutes and hours are incremented as the previous counter overflows. Since the register pair is 16 bits wide, counting up to overflow the register directly from a 32.768 kHz clock would take 2 seconds. To force the overflow at the required one-second intervals, it is necessary to preload it. The simplest method is to set the MSb of TMR1H with a BSF instruction. Note that the TMR1L register is never preloaded or altered; doing so may introduce cumulative error over many cycles. For this method to be accurate, Timer1 must operate in Asynchronous mode and the Timer1 overflow interrupt must be enabled (PIE1<0> = 1) as shown in the routine, RTCinit. The Timer1 oscillator must also be enabled and running at all times. DS39760D-page 118 © 2008 Microchip Technology Inc. PIC18F2450/4450 11.7 Considerations in Asynchronous Counter Mode Following a Timer1 interrupt and an update to the TMR1 registers, the Timer1 module uses a falling edge on its clock source to trigger the next register update on the rising edge. If the update is completed after the clock input has fallen, the next rising edge will not be counted. If the application can reliably update TMR1 before the timer input goes low, no additional action is needed. Otherwise, an adjusted update can be performed EXAMPLE 11-1: following a later Timer1 increment. This can be done by monitoring TMR1L within the interrupt routine until it increments, and then updating the TMR1H:TMR1L register pair while the clock is low, or one-half of the period of the clock source. Assuming that Timer1 is being used as a Real-Time Clock, the clock source is a 32.768 kHz crystal oscillator. In this case, one-half period of the clock is 15.25 μs. The Real-Time Clock application code in Example 11-1 shows a typical ISR for Timer1, as well as the optional code required if the update cannot be done reliably within the required interval. IMPLEMENTING A REAL-TIME CLOCK USING A TIMER1 INTERRUPT SERVICE RTCinit MOVLW MOVWF CLRF MOVLW MOVWF CLRF CLRF MOVLW MOVWF BSF RETURN 80h TMR1H TMR1L b’00001111’ T1CON secs mins .12 hours PIE1, TMR1IE ; Preload TMR1 register pair ; for 1 second overflow ; Configure for external clock, ; Asynchronous operation, external oscillator ; Initialize timekeeping registers ; ; Enable Timer1 interrupt RTCisr BTFSC BRA BTFSS BRA TMR1L,0 $-2 TMR1L,0 $-2 BSF BCF INCF MOVLW CPFSGT RETURN CLRF INCF MOVLW CPFSGT RETURN CLRF INCF MOVLW CPFSGT RETURN CLRF RETURN TMR1H, 7 PIR1, TMR1IF secs, F .59 secs secs mins, F .59 mins mins hours, F .23 hours hours © 2008 Microchip Technology Inc. ; ; ; ; ; ; ; ; ; ; ; ; Insert the next 4 lines of code when TMR1 cannot be reliably updated before clock pulse goes low wait for TMR1L to become clear (may already be clear) wait for TMR1L to become set TMR1 has just incremented If TMR1 update can be completed before clock pulse goes low Start ISR here Preload for 1 sec overflow Clear interrupt flag Increment seconds 60 seconds elapsed? ; ; ; ; No, done Clear seconds Increment minutes 60 minutes elapsed? ; ; ; ; No, done clear minutes Increment hours 24 hours elapsed? ; No, done ; Reset hours ; Done DS39760D-page 119 PIC18F2450/4450 TABLE 11-2: Name INTCON REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER Bit 7 Bit 6 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 IPR1 GIE/GIEH PEIE/GIEL Bit 5 TMR1L Timer1 Register Low Byte TMR1H TImer1 Register High Byte T1CON RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC 50 50 TMR1CS TMR1ON 50 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Timer1 module. DS39760D-page 120 © 2008 Microchip Technology Inc. PIC18F2450/4450 12.0 TIMER2 MODULE 12.1 Timer2 Operation • 8-Bit Timer and Period Registers (TMR2 and PR2, respectively) • Readable and Writable (both registers) • Software Programmable Prescaler (1:1, 1:4 and 1:16) • Software Programmable Postscaler (1:1 through 1:16) • Interrupt on TMR2 to PR2 Match In normal operation, TMR2 is incremented from 00h on each clock (FOSC/4). A 2-bit counter/prescaler on the clock input gives direct input, divide-by-4 and divide-by16 prescale options. These are selected by the prescaler control bits, T2CKPS1:T2CKPS0 (T2CON<1:0>). The value of TMR2 is compared to that of the period register, PR2, on each clock cycle. When the two values match, the comparator generates a match signal as the timer output. This signal also resets the value of TMR2 to 00h on the next cycle and drives the output counter/ postscaler (see Section 12.2 “Timer2 Interrupt”). The module is controlled through the T2CON register (Register 12-1) which enables or disables the timer and configures the prescaler and postscaler. Timer2 can be shut off by clearing control bit, TMR2ON (T2CON<2>), to minimize power consumption. The TMR2 and PR2 registers are both directly readable and writable. The TMR2 register is cleared on any device Reset, while the PR2 register initializes at FFh. Both the prescaler and postscaler counters are cleared on the following events: A simplified block diagram of the module is shown in Figure 12-1. • a write to the TMR2 register • a write to the T2CON register • any device Reset (Power-on Reset, MCLR Reset, Watchdog Timer Reset or Brown-out Reset) The Timer2 module timer incorporates the following features: TMR2 is not cleared when T2CON is written. REGISTER 12-1: T2CON: TIMER2 CONTROL REGISTER U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 Unimplemented: Read as ‘0’ bit 6-3 T2OUTPS3:T2OUTPS0: Timer2 Output Postscale Select bits 0000 = 1:1 Postscale 0001 = 1:2 Postscale • • • 1111 = 1:16 Postscale bit 2 TMR2ON: Timer2 On bit 1 = Timer2 is on 0 = Timer2 is off bit 1-0 T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits 00 = Prescaler is 1 01 = Prescaler is 4 1x = Prescaler is 16 © 2008 Microchip Technology Inc. x = Bit is unknown DS39760D-page 121 PIC18F2450/4450 12.2 Timer2 Interrupt A range of 16 postscale options (from 1:1 through 1:16 inclusive) can be selected with the postscaler control bits, T2OUTPS3:T2OUTPS0 (T2CON<6:3>). Timer2 also can generate an optional device interrupt. The Timer2 output signal (TMR2 to PR2 match) provides the input for the 4-bit output counter/ postscaler. This counter generates the TMR2 match interrupt flag which is latched in TMR2IF (PIR1<1>). The interrupt is enabled by setting the TMR2 Match Interrupt Enable bit, TMR2IE (PIE1<1>). FIGURE 12-1: 12.3 TMR2 Output The unscaled output of TMR2 is available primarily to the CCP module, where it is used as a time base for operations in PWM mode. TIMER2 BLOCK DIAGRAM 4 T2OUTPS3:T2OUTPS0 T2CKPS1:T2CKPS0 Set TMR2IF 2 TMR2 Output (to PWM) 1:1, 1:4, 1:16 Prescaler FOSC/4 1:1 to 1:16 Postscaler TMR2/PR2 Match Reset Comparator TMR2 8 PR2 8 8 Internal Data Bus TABLE 12-1: Name REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER Bit 7 Bit 6 INTCON GIE/GIEH PEIE/GIEL Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 TMR2 T2CON PR2 Timer2 Register — 50 T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0 Timer2 Period Register 50 50 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Timer2 module. DS39760D-page 122 © 2008 Microchip Technology Inc. PIC18F2450/4450 13.0 CAPTURE/COMPARE/PWM (CCP) MODULE PIC18F2450/4450 devices have one CCP (Capture/ Compare/PWM) module. The module contains a 16-bit register, which can operate as a 16-bit Capture register, a 16-bit Compare register or a PWM Master/Slave Duty Cycle register. REGISTER 13-1: CCP1CON: CAPTURE/COMPARE/PWM CONTROL REGISTER U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 DC1B1:DC1B0: PWM Duty Cycle for CCP Module bits Capture mode: Unused. Compare mode: Unused. PWM mode: These bits are the two LSbs (bit 1 and bit 0) of the 10-bit PWM duty cycle. The eight MSbs of the duty cycle are found in CCPR1L. bit 3-0 CCP1M3:CCP1M0: CCP Module Mode Select bits 0000 = Capture/Compare/PWM disabled (resets CCP module) 0001 = Reserved 0010 = Compare mode: toggle output on match (CCP1IF bit is set) 0011 = Reserved 0100 = Capture mode: every falling edge 0101 = Capture mode: every rising edge 0110 = Capture mode: every 4th rising edge 0111 = Capture mode: every 16th rising edge 1000 = Compare mode: initialize CCP1 pin low; on compare match, force CCP1 pin high (CCP1IF bit is set) 1001 = Compare mode: initialize CCP1 pin high; on compare match, force CCP1 pin low (CCP1IF bit is set) 1010 = Compare mode: generate software interrupt on compare match (CCP1IF bit is set, CCP1 pin reflects I/O state) 1011 = Compare mode: trigger special event, reset timer and start A/D conversion on CCP1 match (CCP1IF bit is set) 11xx = PWM mode © 2008 Microchip Technology Inc. DS39760D-page 123 PIC18F2450/4450 13.1 CCP Module Configuration 13.2.1 The Capture/Compare/PWM module is associated with a control register (generically, CCP1CON) and a data register (CCPR1). The data register, in turn, is comprised of two 8-bit registers: CCPR1L (low byte) and CCPR1H (high byte). All registers are both readable and writable. 13.1.1 CCP MODULE AND TIMER RESOURCES TABLE 13-1: CCP MODE – TIMER RESOURCE CCP Mode Timer Resource Capture Compare PWM Timer1 Timer1 Timer2 Capture Mode In Capture mode, the CCPR1H:CCPR1L register pair captures the 16-bit value of the TMR1 register when an event occurs on the corresponding CCP1 pin. An event is defined as one of the following: • • • • If RC2/CCP1 is configured as an output, a write to the port can cause a capture condition. SOFTWARE INTERRUPT When the Capture mode is changed, a false capture interrupt may be generated. The user should keep the CCP1IE interrupt enable bit clear to avoid false interrupts. The interrupt flag bit, CCP1IF, should also be cleared following any such change in operating mode. CCP PRESCALER There are four prescaler settings in Capture mode. They are specified as part of the operating mode selected by the mode select bits (CCP1M3:CCP1M0). Whenever the CCP module is turned off or Capture mode is disabled, the prescaler counter is cleared. This means that any Reset will clear the prescaler counter. Switching from one capture prescaler to another may generate an interrupt. Also, the prescaler counter will not be cleared, therefore, the first capture may be from a non-zero prescaler. Example 13-1 shows the recommended method for switching between capture prescalers. This example also clears the prescaler counter and will not generate the “false” interrupt. EXAMPLE 13-1: every falling edge every rising edge every 4th rising edge every 16th rising edge The event is selected by the mode select bits, CCP1M3:CCP1M0 (CCP1CON<3:0>). When a capture is made, the interrupt request flag bit, CCP1IF, is set; it must be cleared in software. If another capture occurs before the value in register CCPR1 is read, the old captured value is overwritten by the new captured value. FIGURE 13-1: Note: 13.2.3 In Timer1 in Asynchronous Counter mode, the capture operation will not work. 13.2 In Capture mode, the CCP1 pin should be configured as an input by setting the corresponding TRIS direction bit. 13.2.2 The CCP module utilizes Timer1 or Timer2, depending on the mode selected. Timer1 is available to the module in Capture or Compare modes, while Timer2 is available for modules in PWM mode. CCP1 PIN CONFIGURATION CHANGING BETWEEN CAPTURE PRESCALERS (CCP1 SHOWN) CLRF MOVLW CCP1CON NEW_CAPT_PS MOVWF CCP1CON ; ; ; ; ; ; Turn CCP module off Load WREG with the new prescaler mode value and CCP ON Load CCP1CON with this value CAPTURE MODE OPERATION BLOCK DIAGRAM Set CCP1IF CCP1 pin Prescaler ÷ 1, 4, 16 and Edge Detect CCPR1H CCPR1L TMR1 Enable CCP1CON<3:0> Q1:Q4 DS39760D-page 124 4 TMR1H TMR1L 4 © 2008 Microchip Technology Inc. PIC18F2450/4450 13.3 Compare Mode 13.3.3 In Compare mode, the 16-bit CCPR1 register value is constantly compared against the TMR1 register pair value. When a match occurs, the CCP1 pin can be: • • • • driven high driven low toggled (high-to-low or low-to-high) remain unchanged (that is, reflects the state of the I/O latch) The action on the pin is based on the value of the mode select bits (CCP1M3:CCP1M0). At the same time, the interrupt flag bit, CCP1IF, is set. 13.3.1 CCP1 PIN CONFIGURATION The user must configure the CCP1 pin as an output by clearing the appropriate TRIS bit. Note: 13.3.2 Clearing the CCP1CON register will force the RC2 compare output latch to the default low level. SOFTWARE INTERRUPT MODE When the Generate Software Interrupt mode is chosen (CCP1M3:CCP1M0 = 1010), the CCP1 pin is not affected. Only a CCP interrupt is generated, if enabled, and the CCP1IE bit is set. 13.3.4 SPECIAL EVENT TRIGGER The CCP module is equipped with a Special Event Trigger. This is an internal hardware signal generated in Compare mode to trigger actions by other modules. The Special Event Trigger is enabled by selecting the Compare Special Event Trigger mode (CCP1M3:CCP1M0 = 1011). For the CCP module, the Special Event Trigger resets the Timer1 register pair. This allows the CCPR1 registers to serve as a programmable period register for the Timer1. The Special Event Trigger for CCP1 can also start an A/D conversion. In order to do this, the A/D Converter must already be enabled. TIMER1 MODE SELECTION Timer1 must be running in Timer mode, or Synchronized Counter mode, if the CCP module is using the compare feature. In Asynchronous Counter mode, the compare operation may not work. FIGURE 13-2: COMPARE MODE OPERATION BLOCK DIAGRAM CCPR1H CCPR1L Set CCP1IF Special Event Trigger (Timer1 Reset) CCP1 pin Comparator Compare Match Output Logic 4 S Q R TRIS Output Enable CCP1CON<3:0> TMR1H TMR1L © 2008 Microchip Technology Inc. DS39760D-page 125 PIC18F2450/4450 TABLE 13-2: Name INTCON REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, TIMER1 Bit 7 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 Bit 6 GIE/GIEH PEIE/GIEL (1) — RI TO PD POR BOR 50 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 TRISC7 TRISC6 — — — TRISC2 TRISC1 TRISC0 RCON TRISC IPEN SBOREN 51 TMR1L Timer1 Register Low Byte 50 TMR1H Timer1 Register High Byte 50 T1CON RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC CCPR1L Capture/Compare/PWM Register 1 Low Byte CCPR1H Capture/Compare/PWM Register 1 High Byte CCP1CON — — DC1B1 DC1B0 TMR1CS TMR1ON 50 50 50 CCP1M3 CCP1M2 CCP1M1 CCP1M0 50 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by capture/compare and Timer1. Note 1: The SBOREN bit is only available when BOREN<1:0> = 01; otherwise, the bit reads as ‘0’. DS39760D-page 126 © 2008 Microchip Technology Inc. PIC18F2450/4450 13.4 PWM Mode 13.4.1 In Pulse-Width Modulation (PWM) mode, the CCP1 pin produces up to a 10-bit resolution PWM output. Figure 13-3 shows a simplified block diagram of the CCP module in PWM mode. For a step-by-step procedure on how to set up the CCP module for PWM operation, see Section 13.4.3 “Setup for PWM Operation”. FIGURE 13-3: SIMPLIFIED PWM BLOCK DIAGRAM CCP1CON<5:4> Duty Cycle Registers The PWM period is specified by writing to the PR2 register. The PWM period can be calculated using the following formula: EQUATION 13-1: PWM Period = [(PR2) + 1] • 4 • TOSC • (TMR2 Prescale Value) PWM frequency is defined as 1/[PWM period]. When TMR2 is equal to PR2, the following three events occur on the next increment cycle: • TMR2 is cleared • The CCP1 pin is set (exception: if PWM duty cycle = 0%, the CCP1 pin will not be set) • The PWM duty cycle is latched from CCPR1L into CCPR1H CCPR1L CCPR1H (Slave) Note: R Comparator Comparator S Clear Timer, CCP1 pin and latch D.C. PR2 Q CCP1 Output (Note 1) TMR2 Corresponding TRIS bit Note 1: The 8-bit TMR2 value is concatenated with the 2-bit internal Q clock, or 2 bits of the prescaler, to create the 10-bit time base. A PWM output (Figure 13-4) has a time base (period) and a time that the output stays high (duty cycle). The frequency of the PWM is the inverse of the period (1/period). FIGURE 13-4: PWM PERIOD PWM OUTPUT 13.4.2 The Timer2 postscalers (see Section 12.0 “Timer2 Module”) are not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output. PWM DUTY CYCLE The PWM duty cycle is specified by writing to the CCPR1L register and to the CCP1CON<5:4> bits. Up to 10-bit resolution is available. The CCPR1L contains the eight MSbs and the CCP1CON<5:4> bits contain the two LSbs. This 10-bit value is represented by CCPR1L:CCP1CON<5:4>. Equation 13-2 is used to calculate the PWM duty cycle in time: EQUATION 13-2: PWM Duty Cycle = (CCPR1L:CCP1CON<5:4>) • TOSC • (TMR2 Prescale Value) Period Duty Cycle TMR2 = PR2 CCPR1L and CCP1CON<5:4> can be written to at any time, but the duty cycle value is not latched into CCPR1H until after a match between PR2 and TMR2 occurs (i.e., the period is complete). In PWM mode, CCPR1H is a read-only register. TMR2 = Duty Cycle TMR2 = PR2 © 2008 Microchip Technology Inc. DS39760D-page 127 PIC18F2450/4450 The CCPR1H register and a 2-bit internal latch are used to double-buffer the PWM duty cycle. This double-buffering is essential for glitchless PWM operation. When the CCPR1H and 2-bit latch match TMR2, concatenated with an internal 2-bit Q clock or 2 bits of the TMR2 prescaler, the CCP1 pin is cleared. The maximum PWM resolution (bits) for a given PWM frequency is given by the equation: F OSC log ⎛ ---------------⎞ ⎝ F PWM⎠ PWM Resolution (max) = -----------------------------bits log ( 2 ) 2. 3. 5. Set the PWM period by writing to the PR2 register. Set the PWM duty cycle by writing to the CCPR1L register and CCP1CON<5:4> bits. Make the CCP1 pin an output by clearing the appropriate TRIS bit. Set the TMR2 prescale value, then enable Timer2 by writing to T2CON. Configure the CCP module for PWM operation. EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 40 MHz PWM Frequency 2.44 kHz 9.77 kHz 39.06 kHz 156.25 kHz 312.50 kHz 416.67 kHz 16 4 1 1 1 1 FFh FFh FFh 3Fh 1Fh 17h 10 10 10 8 7 6.58 Timer Prescaler (1, 4, 16) PR2 Value Maximum Resolution (bits) TABLE 13-4: INTCON 1. If the PWM duty cycle value is longer than the PWM period, the CCP1 pin will not be cleared. TABLE 13-3: Name SETUP FOR PWM OPERATION The following steps should be taken when configuring the CCP module for PWM operation: 4. EQUATION 13-3: Note: 13.4.3 REGISTERS ASSOCIATED WITH PWM AND TIMER2 Bit 7 Bit 6 GIE/GIEH PEIE/GIEL Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 IPEN SBOREN(1) — RI TO PD POR BOR 50 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 TRISC7 TRISC6 — — — TRISC2 TRISC1 TRISC0 51 RCON TRISC TMR2 Timer2 Register PR2 Timer2 Period Register T2CON — 50 50 T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0 50 CCPR1L Capture/Compare/PWM Register 1 Low Byte 50 CCPR1H Capture/Compare/PWM Register 1 High Byte 50 CCP1CON — — DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 50 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PWM or Timer2. Note 1: The SBOREN bit is only available when BOREN<1:0> = 01; otherwise, the bit reads as ‘0’. DS39760D-page 128 © 2008 Microchip Technology Inc. PIC18F2450/4450 14.0 any USB host and the PIC® microcontroller. The SIE can be interfaced directly to the USB, utilizing the internal transceiver, or it can be connected through an external transceiver. An internal 3.3V regulator is also available to power the internal transceiver in 5V applications. UNIVERSAL SERIAL BUS (USB) This section describes the details of the USB peripheral. Because of the very specific nature of the module, knowledge of USB is expected. Some high-level USB information is provided in Section 14.9 “Overview of USB” only for application design reference. Designers are encouraged to refer to the official specification published by the USB Implementers Forum (USB-IF) for the latest information. USB Specification Revision 2.0 is the most current specification at the time of publication of this document. 14.1 Some special hardware features have been included to improve performance. Dual port memory in the device’s data memory space (USB RAM) has been supplied to share direct memory access between the microcontroller core and the SIE. Buffer descriptors are also provided, allowing users to freely program endpoint memory usage within the USB RAM space. Figure 14-1 presents a general overview of the USB peripheral and its features. Overview of the USB Peripheral The PIC18F2450/4450 device family contains a fullspeed and low-speed, compatible USB Serial Interface Engine (SIE) that allows fast communication between FIGURE 14-1: USB PERIPHERAL AND OPTIONS PIC18F2450/4450 Family 3.3V Regulator VREGEN External 3.3V Supply(3) VUSB EN P FSEN UPUEN UTRDIS P Transceiver OE USB Control and Configuration USB SIE (Full Speed) Internal Pull-ups FS USB Clock from the Oscillator Module External Pull-ups(2) (Low Speed) USB Bus D+ DUOE(1) VM(1) VP(1) RCV(1) VMO(1) VPO(1) External Transceiver USB Bus 256-Byte USB RAM Note 1: This signal is only available if the internal transceiver is disabled (UTRDIS = 1). 2: The pull-ups can be supplied either from the VUSB pin or from an external 3.3V supply. 3: Do not enable the internal regulator when using an external 3.3V supply. © 2008 Microchip Technology Inc. DS39760D-page 129 PIC18F2450/4450 14.2 USB Status and Control In addition, the USB Control register contains a status bit, SE0 (UCON<5>), which is used to indicate the occurrence of a single-ended zero on the bus. When the USB module is enabled, this bit should be monitored to determine whether the differential data lines have come out of a single-ended zero condition. This helps to differentiate the initial power-up state from the USB Reset signal. The operation of the USB module is configured and managed through three control registers. In addition, a total of 22 registers are used to manage the actual USB transactions. The registers are: • • • • • • USB Control register (UCON) USB Configuration register (UCFG) USB Transfer Status register (USTAT) USB Device Address register (UADDR) Frame Number registers (UFRMH:UFRML) Endpoint Enable registers 0 through 15 (UEPn) 14.2.1 The overall operation of the USB module is controlled by the USBEN bit (UCON<3>). Setting this bit activates the module and resets all of the PPBI bits in the Buffer Descriptor Table to ‘0’. This bit also activates the onchip voltage regulator, if enabled. Thus, this bit can be used as a soft attach/detach to the USB. Although all status and control bits are ignored when this bit is clear, the module needs to be fully preconfigured prior to setting this bit. USB CONTROL REGISTER (UCON) The USB Control register (Register 14-1) contains bits needed to control the module behavior during transfers. The register contains bits that control the following: • • • • Main USB Peripheral Enable Ping-Pong Buffer Pointer Reset Control of the Suspend Mode Packet Transfer Disable REGISTER 14-1: UCON: USB CONTROL REGISTER U-0 R/W-0 R-x R/C-0 R/W-0 R/W-0 R/W-0 U-0 — PPBRST SE0 PKTDIS USBEN RESUME SUSPND — bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 Unimplemented: Read as ‘0’ bit 6 PPBRST: Ping-Pong Buffers Reset bit 1 = Reset all Ping-Pong Buffer Pointers to the EVEN Buffer Descriptor (BD) banks 0 = Ping-Pong Buffer Pointers not being reset bit 5 SE0: Live Single-Ended Zero Flag bit 1 = Single-ended zero active on the USB bus 0 = No single-ended zero detected bit 4 PKTDIS: Packet Transfer Disable bit 1 = SIE token and packet processing disabled, automatically set when a SETUP token is received 0 = SIE token and packet processing enabled bit 3 USBEN: USB Module Enable bit 1 = USB module and supporting circuitry enabled (device attached) 0 = USB module and supporting circuitry disabled (device detached) bit 2 RESUME: Resume Signaling Enable bit 1 = Resume signaling activated 0 = Resume signaling disabled bit 1 SUSPND: Suspend USB bit 1 = USB module and supporting circuitry in Power Conserve mode, SIE clock inactive 0 = USB module and supporting circuitry in normal operation, SIE clock clocked at the configured rate bit 0 Unimplemented: Read as ‘0’ DS39760D-page 130 © 2008 Microchip Technology Inc. PIC18F2450/4450 The PPBRST bit (UCON<6>) controls the Reset status when Double-Buffering mode (ping-pong buffering) is used. When the PPBRST bit is set, all Ping-Pong Buffer Pointers are set to the EVEN buffers. PPBRST has to be cleared by firmware. This bit is ignored in buffering modes not using ping-pong buffering. The PKTDIS bit (UCON<4>) is a flag indicating that the SIE has disabled packet transmission and reception. This bit is set by the SIE when a SETUP token is received to allow setup processing. This bit cannot be set by the microcontroller, only cleared; clearing it allows the SIE to continue transmission and/or reception. Any pending events within the Buffer Descriptor Table will still be available, indicated within the USTAT register’s FIFO buffer. The RESUME bit (UCON<2>) allows the peripheral to perform a remote wake-up by executing Resume signaling. To generate a valid remote wake-up, firmware must set RESUME for 10 ms and then clear the bit. For more information on Resume signaling, see Sections 7.1.7.5, 11.4.4 and 11.9 in the USB 2.0 Specification. The SUSPND bit (UCON<1>) places the module and supporting circuitry (i.e., voltage regulator) in a lowpower mode. The input clock to the SIE is also disabled. This bit should be set by the software in response to an IDLEIF interrupt. It should be reset by the microcontroller firmware after an ACTVIF interrupt is observed. When this bit is active, the device remains attached to the bus but the transceiver outputs remain Idle. The voltage on the VUSB pin may vary depending on the value of this bit. Setting this bit before a IDLEIF request will result in unpredictable bus behavior. Note: 14.2.2 While in Suspend mode, a typical bus powered USB device is limited to 500 μA of current. This is the complete current drawn by the PIC microcontroller and its supporting circuitry. Care should be taken to assure minimum current draw when the device enters Suspend mode. USB CONFIGURATION REGISTER (UCFG) The UCFG register also contains two bits which aid in module testing, debugging and USB certifications. These bits control output enable state monitoring and eye pattern generation. Note: 14.2.2.1 • Bus Speed (full speed versus low speed) • On-Chip Transceiver Enable • Ping-Pong Buffer Usage © 2008 Microchip Technology Inc. Internal Transceiver The USB peripheral has a built-in, USB 2.0, full-speed and low-speed compliant transceiver, internally connected to the SIE. This feature is useful for low-cost, single chip applications. The UTRDIS bit (UCFG<3>) controls the transceiver; it is enabled by default (UTRDIS = 0). The FSEN bit (UCFG<2>) controls the transceiver speed; setting the bit enables full-speed operation. The on-chip USB pull-up resistors are controlled by the UPUEN bit (UCFG<4>). They can only be selected when the on-chip transceiver is enabled. The USB specification requires 3.3V operation for communications; however, the rest of the chip may be running at a higher voltage. Thus, the transceiver is supplied power from a separate source, VUSB. 14.2.2.2 External Transceiver This module provides support for use with an off-chip transceiver. The off-chip transceiver is intended for applications where physical conditions dictate the location of the transceiver to be away from the SIE. For example, applications that require isolation from the USB could use an external transceiver through some isolation to the microcontroller’s SIE (Figure 14-2). External transceiver operation is enabled by setting the UTRDIS bit. FIGURE 14-2: PIC® Microcontroller TYPICAL EXTERNAL TRANSCEIVER WITH ISOLATION VDD Isolated from USB 3.3V Derived from USB VDD VUSB Prior to communicating over USB, the module’s associated internal and/or external hardware must be configured. Most of the configuration is performed with the UCFG register (Register 14-2). The separate USB voltage regulator (see Section 14.2.2.8 “Internal Regulator”) is controlled through the Configuration registers. The UFCG register contains most of the bits that control the system level behavior of the USB module. These include: The USB speed, transceiver and pull-up should only be configured during the module setup phase. It is not recommended to switch these settings while the module is enabled. VM VP RCV VMO VPO UOE Note: 1.5 kΩ Isolation Transceiver D+ D- The above setting shows a simplified schematic for a full-speed configuration using an external transceiver with isolation. DS39760D-page 131 PIC18F2450/4450 REGISTER 14-2: UCFG: USB CONFIGURATION REGISTER R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 UTEYE UOEMON(1) — UPUEN(2,3) UTRDIS(2) FSEN(2) PPB1 PPB0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 UTEYE: USB Eye Pattern Test Enable bit 1 = Eye pattern test enabled 0 = Eye pattern test disabled bit 6 UOEMON: USB OE Monitor Enable bit(1) 1 = UOE signal active; it indicates intervals during which the D+/D- lines are driving 0 = UOE signal inactive bit 5 Unimplemented: Read as ‘0’ bit 4 UPUEN: USB On-Chip Pull-up Enable bit(2,3) 1 = On-chip pull-up enabled (pull-up on D+ with FSEN = 1 or D- with FSEN = 0) 0 = On-chip pull-up disabled bit 3 UTRDIS: On-Chip Transceiver Disable bit(2) 1 = On-chip transceiver disabled; digital transceiver interface enabled 0 = On-chip transceiver active bit 2 FSEN: Full-Speed Enable bit(2) 1 = Full-speed device: controls transceiver edge rates; requires input clock at 48 MHz 0 = Low-speed device: controls transceiver edge rates; requires input clock at 6 MHz bit 1-0 PPB1:PPB0: Ping-Pong Buffers Configuration bits 11 = Enabled for all endpoints except Endpoint 0 10 = EVEN/ODD ping-pong buffers enabled for all endpoints 01 = EVEN/ODD ping-pong buffer enabled for OUT Endpoint 0 00 = EVEN/ODD ping-pong buffers disabled Note 1: 2: 3: If UTRDIS is set, the UOE signal will be active independent of the UOEMON bit setting. The UPUEN, UTRDIS and FSEN bits should never be changed while the USB module is enabled. These values must be preconfigured prior to enabling the module. This bit is only valid when the on-chip transceiver is active (UTRDIS = 0); otherwise, it is ignored. There are 6 signals from the module to communicate with and control an external transceiver: • • • • • • VM: Input from the single-ended D- line VP: Input from the single-ended D+ line RCV: Input from the differential receiver VMO: Output to the differential line driver VPO: Output to the differential line driver UOE: Output enable DS39760D-page 132 The VPO and VMO signals are outputs from the SIE to the external transceiver. The RCV signal is the output from the external transceiver to the SIE; it represents the differential signals from the serial bus translated into a single pulse train. The VM and VP signals are used to report conditions on the serial bus to the SIE that can’t be captured with the RCV signal. The combinations of states of these signals and their interpretation are listed in Table 14-1 and Table 14-2. © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 14-1: DIFFERENTIAL OUTPUTS TO TRANSCEIVER VPO VMO Bus State 0 0 Single-Ended Zero 0 1 Differential ‘0’ 1 0 Differential ‘1’ 1 1 Illegal Condition TABLE 14-2: SINGLE-ENDED INPUTS FROM TRANSCEIVER VP VM Bus State 0 0 Single-Ended Zero 0 1 Low Speed 1 0 High Speed 1 1 Error The UOE signal toggles the state of the external transceiver. This line is pulled low by the device to enable the transmission of data from the SIE to an external device. 14.2.2.3 Internal Pull-up Resistors The PIC18F2450/4450 devices have built-in pull-up resistors designed to meet the requirements for lowspeed and full-speed USB. The UPUEN bit (UCFG<4>) enables the internal pull-ups. Figure 14-1 shows the pull-ups and their control. 14.2.2.4 Pull-up Resistors The PIC18F2450/4450 devices require an external pull-up resistor to meet the requirements for low-speed and full-speed USB. Either an external 3.3V supply or the VUSB pin may be used to pull up D+ or D-. The pullup resistor must be 1.5 kΩ (±5%) as required by the USB specifications. Figure 14-3 shows an example with the VUSB pin. FIGURE 14-3: EXTERNAL CIRCUITRY PIC® Microcontroller Host Controller/HUB VUSB 1.5 kΩ D+ DNote: The above setting shows a typical connection for a full-speed configuration using an on-chip regulator and an external pull-up resistor. 14.2.2.5 Ping-Pong Buffer Configuration 14.2.2.6 USB Output Enable Monitor The USB OE monitor provides indication as to whether the SIE is listening to the bus or actively driving the bus. This is enabled by default when using an external transceiver or when UCFG<6> = 1. The USB OE monitoring is useful for initial system debugging, as well as scope triggering during eye pattern generation tests. 14.2.2.7 Eye Pattern Test Enable An automatic eye pattern test can be generated by the module when the UCFG<7> bit is set. The eye pattern output will be observable based on module settings, meaning that the user is first responsible for configuring the SIE clock settings, pull-up resistor and Transceiver mode. In addition, the module has to be enabled. Once UTEYE is set, the module emulates a switch from a receive to transmit state and will start transmitting a J-K-J-K bit sequence (K-J-K-J for full speed). The sequence will be repeated indefinitely while the Eye Pattern Test mode is enabled. Note that this bit should never be set while the module is connected to an actual USB system. This test mode is intended for board verification to aid with USB certification tests. It is intended to show a system developer the noise integrity of the USB signals which can be affected by board traces, impedance mismatches and proximity to other system components. It does not properly test the transition from a receive to a transmit state. Although the eye pattern is not meant to replace the more complex USB certification test, it should aid during first order system debugging. 14.2.2.8 Internal Regulator The PIC18F2450/4450 devices have a built-in 3.3V regulator to provide power to the internal transceiver and provide a source for the external pull-ups. An external 220 nF (±20%) capacitor is required for stability. Note: The drive from VUSB is sufficient to only drive an external pull-up in addition to the internal transceiver. The regulator is disabled by default and can be enabled through the VREGEN Configuration bit. When enabled, the voltage is visible on pin VUSB. When the regulator is disabled, a 3.3V source must be provided through the VUSB pin for the internal transceiver. If the internal transceiver is disabled, VUSB is not used. Note 1: Do not enable the internal regulator if an external regulator is connected to VUSB. 2: VDD must be greater than or equal to VUSB at all times, even with the regulator disabled. The usage of ping-pong buffers is configured using the PPB1:PPB0 bits. Refer to Section 14.4.4 “Ping-Pong Buffering” for a complete explanation of the ping-pong buffers. © 2008 Microchip Technology Inc. DS39760D-page 133 PIC18F2450/4450 14.2.3 USB STATUS REGISTER (USTAT) Clearing the transfer complete flag bit, TRNIF, causes the SIE to advance the FIFO. If the next data in the FIFO holding register is valid, the SIE will reassert the interrupt within 6 TCY of clearing TRNIF. If no additional data is present, TRNIF will remain clear; USTAT data will no longer be reliable. The USB Status register reports the transaction status within the SIE. When the SIE issues a USB transfer complete interrupt, USTAT should be read to determine the status of the transfer. USTAT contains the transfer endpoint number, direction and Ping-Pong Buffer Pointer value (if used). Note: Note: The data in the USB Status register is valid only when the TRNIF interrupt flag is asserted. The USTAT register is actually a read window into a four-byte status FIFO, maintained by the SIE. It allows the microcontroller to process one transfer while the SIE processes additional endpoints (Figure 14-4). When the SIE completes using a buffer for reading or writing data, it updates the USTAT register. If another USB transfer is performed before a transaction complete interrupt is serviced, the SIE will store the status of the next transfer into the status FIFO. If an endpoint request is received while the USTAT FIFO is full, the SIE will automatically issue a NAK back to the host. FIGURE 14-4: USTAT FIFO USTAT from SIE Clearing TRNIF Advances FIFO 4-Byte FIFO for USTAT Data Bus REGISTER 14-3: USTAT: USB STATUS REGISTER U-0 R-x R-x R-x R-x R-x R-x U-0 — ENDP3 ENDP2 ENDP1 ENDP0 DIR PPBI(1) — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 Unimplemented: Read as ‘0’ bit 6-3 ENDP3:ENDP0: Encoded Number of Last Endpoint Activity bits (represents the number of the BDT updated by the last USB transfer) 1111 = Endpoint 15 1110 = Endpoint 14 .... 0001 = Endpoint 1 0000 = Endpoint 0 bit 2 DIR: Last BD Direction Indicator bit 1 = The last transaction was an IN token 0 = The last transaction was an OUT or SETUP token bit 1 PPBI: Ping-Pong BD Pointer Indicator bit(1) 1 = The last transaction was to the ODD BD bank 0 = The last transaction was to the EVEN BD bank bit 0 Unimplemented: Read as ‘0’ Note 1: x = Bit is unknown This bit is only valid for endpoints with available EVEN and ODD BD registers. DS39760D-page 134 © 2008 Microchip Technology Inc. PIC18F2450/4450 14.2.4 USB ENDPOINT CONTROL Each of the 16 possible bidirectional endpoints has its own independent control register, UEPn (where ‘n’ represents the endpoint number). Each register has an identical complement of control bits. The prototype is shown in Register 14-4. The EPHSHK bit (UEPn<4>) controls handshaking for the endpoint; setting this bit enables USB handshaking. Typically, this bit is always set except when using isochronous endpoints. The EPCONDIS bit (UEPn<3>) is used to enable or disable USB control operations (SETUP) through the endpoint. Clearing this bit enables SETUP transactions. Note that the corresponding EPINEN and EPOUTEN bits must be set to enable IN and OUT REGISTER 14-4: transactions. For Endpoint 0, this bit should always be cleared since the USB specifications identify Endpoint 0 as the default control endpoint. The EPOUTEN bit (UEPn<2>) is used to enable or disable USB OUT transactions from the host. Setting this bit enables OUT transactions. Similarly, the EPINEN bit (UEPn<1>) enables or disables USB IN transactions from the host. The EPSTALL bit (UEPn<0>) is used to indicate a STALL condition for the endpoint. If a STALL is issued on a particular endpoint, the EPSTALL bit for that endpoint pair will be set by the SIE. This bit remains set until it is cleared through firmware, or until the SIE is reset. UEPn: USB ENDPOINT n CONTROL REGISTER (UEP0 THROUGH UEP15) U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-5 Unimplemented: Read as ‘0’ bit 4 EPHSHK: Endpoint Handshake Enable bit 1 = Endpoint handshake enabled 0 = Endpoint handshake disabled (typically used for isochronous endpoints) bit 3 EPCONDIS: Bidirectional Endpoint Control bit If EPOUTEN = 1 and EPINEN = 1: 1 = Disable Endpoint n from control transfers; only IN and OUT transfers allowed 0 = Enable Endpoint n for control (SETUP) transfers; IN and OUT transfers also allowed bit 2 EPOUTEN: Endpoint Output Enable bit 1 = Endpoint n output enabled 0 = Endpoint n output disabled bit 1 EPINEN: Endpoint Input Enable bit 1 = Endpoint n input enabled 0 = Endpoint n input disabled bit 0 EPSTALL: Endpoint Stall Indicator bit 1 = Endpoint n has issued one or more STALL packets 0 = Endpoint n has not issued any STALL packets © 2008 Microchip Technology Inc. DS39760D-page 135 PIC18F2450/4450 14.2.5 USB ADDRESS REGISTER (UADDR) The USB Address register contains the unique USB address that the peripheral will decode when active. UADDR is reset to 00h when a USB Reset is received, indicated by URSTIF, or when a Reset is received from the microcontroller. The USB address must be written by the microcontroller during the USB setup phase (enumeration) as part of the Microchip USB firmware support. 14.2.6 USB FRAME NUMBER REGISTERS (UFRMH:UFRML) The Frame Number registers contain the 11-bit frame number. The low-order byte is contained in UFRML, while the three high-order bits are contained in UFRMH. The register pair is updated with the current frame number whenever a SOF token is received. For the microcontroller, these registers are read-only. The Frame Number register is primarily used for isochronous transfers. 14.3 USB RAM FIGURE 14-5: Banks 0 to 1 Banks 2 to 3 Bank 4 IMPLEMENTATION OF USB RAM IN DATA MEMORY SPACE 000h User Data 1FFh 200h Unused Buffer Descriptors, USB Data or User Data 3FFh 400h 4FFh 500h USB Data or User Data Banks 5 to 14 7FFh 800h Unused USB data moves between the microcontroller core and the SIE through a memory space known as the USB RAM. This is a special dual port memory that is mapped into the normal data memory space in Bank 4 (400h to 4FFh) for a total of 256 bytes (Figure 14-5). Some portion of Bank 4 (400h through 4FFh) is used specifically for endpoint buffer control, while the remaining portion is available for USB data. Depending on the type of buffering being used, all but 8 bytes of Bank 4 may also be available for use as USB buffer space. Although USB RAM is available to the microcontroller as data memory, the sections that are being accessed by the SIE should not be accessed by the microcontroller. A semaphore mechanism is used to determine the access to a particular buffer at any given time. This is discussed in Section 14.4.1.1 “Buffer Ownership”. DS39760D-page 136 Bank15 SFRs F00h F80h FFFh © 2008 Microchip Technology Inc. PIC18F2450/4450 14.4 Buffer Descriptors and the Buffer Descriptor Table The registers in Bank 4 are used specifically for endpoint buffer control in a structure known as the Buffer Descriptor Table (BDT). This provides a flexible method for users to construct and control endpoint buffers of various lengths and configuration. The BDT is composed of Buffer Descriptors (BD) which are used to define and control the actual buffers in the USB RAM space. Each BD, in turn, consists of four registers, where n represents one of the 64 possible BDs (range of 0 to 63): • • • • BDnSTAT: BD Status register BDnCNT: BD Byte Count register BDnADRL: BD Address Low register BDnADRH: BD Address High register BDs always occur as a four-byte block in the sequence, BDnSTAT:BDnCNT:BDnADRL:BDnADRH. The address of BDnSTAT is always an offset of (4n – 1) (in hexadecimal) from 400h, with n being the buffer descriptor number. Depending on the buffering configuration used (Section 14.4.4 “Ping-Pong Buffering”), there are up to 32, 33 or 64 sets of buffer descriptors. At a minimum, the BDT must be at least 8 bytes long. This is because the USB specification mandates that every device must have Endpoint 0 with both input and output for initial setup. Depending on the endpoint and buffering configuration, the BDT can be as long as 256 bytes. Although they can be thought of as Special Function Registers, the Buffer Descriptor Status and Address registers are not hardware mapped, as conventional microcontroller SFRs in Bank 15 are. If the endpoint corresponding to a particular BD is not enabled, its registers are not used. Instead of appearing as unimplemented addresses, however, they appear as available RAM. Only when an endpoint is enabled by setting the UEPn<1> bit does the memory at those addresses become functional as BD registers. As with any address in the data memory space, the BD registers have an indeterminate value on any device Reset. A total of 256 bytes of address space in Bank 4 is available for BDT and USB data RAM. In Ping-Pong Buffer mode, all the 16 bidirectional endpoints can not be implemented where BDT itself can be as long as 256 bytes. In the majority of USB applications, few endpoints are required to be implemented. Hence, a small portion of the 256 bytes will be used for BDT and the rest can be used for USB data. An example of a BD for a 16-byte buffer, starting at 480h, is shown in Figure 14-6. A particular set of BD registers is only valid if the corresponding endpoint has been enabled using the UEPn register. All BD registers are available in USB RAM. The BD for each endpoint should be set up prior to enabling the endpoint. © 2008 Microchip Technology Inc. 14.4.1 BD STATUS AND CONFIGURATION Buffer descriptors not only define the size of an endpoint buffer, but also determine its configuration and control. Most of the configuration is done with the BD Status register, BDnSTAT. Each BD has its own unique and correspondingly numbered BDnSTAT register. FIGURE 14-6: Buffer Descriptor EXAMPLE OF A BUFFER DESCRIPTOR Address Registers Contents 400h BD0STAT (xxh) 401h BD0CNT 10h 402h BD0ADRL 80h 403h BD0ADRH 04h Size of Block Starting Address 480h USB Data Buffer 48Fh Note: Memory regions are not to scale. Unlike other control registers, the bit configuration for the BDnSTAT register is context sensitive. There are two distinct configurations, depending on whether the microcontroller or the USB module is modifying the BD and buffer at a particular time. Only three bit definitions are shared between the two. 14.4.1.1 Buffer Ownership Because the buffers and their BDs are shared between the CPU and the USB module, a simple semaphore mechanism is used to distinguish which is allowed to update the BD and associated buffers in memory. This is done by using the UOWN bit (BDnSTAT<7>) as a semaphore to distinguish which is allowed to update the BD and associated buffers in memory. UOWN is the only bit that is shared between the two configurations of BDnSTAT. When UOWN is clear, the BD entry is “owned” by the microcontroller core. When the UOWN bit is set, the BD entry and the buffer memory are “owned” by the USB peripheral. The core should not modify the BD or its corresponding data buffer during this time. Note that the microcontroller core can still read BDnSTAT while the SIE owns the buffer and vice versa. The buffer descriptors have a different meaning based on the source of the register update. Prior to placing ownership with the USB peripheral, the user can configure the basic operation of the peripheral through the BDnSTAT bits. During this time, the byte count and buffer location registers can also be set. DS39760D-page 137 PIC18F2450/4450 When UOWN is set, the user can no longer depend on the values that were written to the BDs. From this point, the SIE updates the BDs as necessary, overwriting the original BD values. The BDnSTAT register is updated by the SIE with the token PID and the transfer count, BDnCNT, is updated. The BDnSTAT byte of the BDT should always be the last byte updated when preparing to arm an endpoint. The SIE will clear the UOWN bit when a transaction has completed. The only exception to this is when KEN is enabled and/or BSTALL is enabled. No hardware mechanism exists to block access when the UOWN bit is set. Thus, unexpected behavior can occur if the microcontroller attempts to modify memory when the SIE owns it. Similarly, reading such memory may produce inaccurate data until the USB peripheral returns ownership to the microcontroller. 14.4.1.2 BDnSTAT Register (CPU Mode) When UOWN = 0, the microcontroller core owns the BD. At this point, the other seven bits of the register take on control functions. The Data Toggle Sync Enable bit, DTSEN (BDnSTAT<3>), controls data toggle parity checking. Setting DTSEN enables data toggle synchronization by the SIE. When enabled, it checks the data packet’s parity against the value of DTS (BDnSTAT<6>). If a packet arrives with an incorrect synchronization, the data will essentially be ignored. It will not be written to TABLE 14-3: the USB RAM and the USB transfer complete interrupt flag will not be set. The SIE will send an ACK token back to the host to Acknowledge receipt, however. The effects of the DTSEN bit on the SIE are summarized in Table 14-3. The Buffer Stall bit, BSTALL (BDnSTAT<2>), provides support for control transfers, usually one-time stalls on Endpoint 0. It also provides support for the SET_FEATURE/CLEAR_FEATURE commands specified in Chapter 9 of the USB specification; typically, continuous STALLs to any endpoint other than the default control endpoint. The BSTALL bit enables buffer stalls. Setting BSTALL causes the SIE to return a STALL token to the host if a received token would use the BD in that location. The EPSTALL bit in the corresponding UEPn control register is set and a STALL interrupt is generated when a STALL is issued to the host. The UOWN bit remains set and the BDs are not changed unless a SETUP token is received. In this case, the STALL condition is cleared and the ownership of the BD is returned to the microcontroller core. The BD9:BD8 bits (BDnSTAT<1:0>) store the two most significant digits of the SIE byte count; the lower 8 digits are stored in the corresponding BDnCNT register. See Section 14.4.2 “BD Byte Count” for more information. EFFECT OF DTSEN BIT ON ODD/EVEN (DATA0/DATA1) PACKET RECEPTION OUT Packet from Host BDnSTAT Settings Device Response after Receiving Packet DTSEN DTS Handshake UOWN TRNIF BDnSTAT and USTAT Status DATA0 1 0 ACK 0 1 Updated DATA1 1 0 ACK 1 0 Not Updated DATA1 1 1 ACK 0 1 Updated DATA0 1 1 ACK 1 0 Not Updated Either 0 x ACK 0 1 Updated Either, with error x x NAK 1 0 Not Updated Legend: x = don’t care DS39760D-page 138 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 14-5: BDnSTAT: BUFFER DESCRIPTOR n STATUS REGISTER (BD0STAT THROUGH BD63STAT), CPU MODE (DATA IS WRITTEN TO THE SIDE) R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x UOWN(1) DTS(2) —(3) —(3) DTSEN BSTALL BC9 BC8 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 UOWN: USB Own bit(1) 0 = The microcontroller core owns the BD and its corresponding buffer bit 6 DTS: Data Toggle Synchronization bit(2) 1 = Data 1 packet 0 = Data 0 packet bit 5-4 Reserved: These bits should always be programmed to ‘0’(3) bit 3 DTSEN: Data Toggle Synchronization Enable bit 1 = Data toggle synchronization is enabled; data packets with incorrect Sync value will be ignored except for a SETUP transaction, which is accepted even if the data toggle bits do not match. 0 = No data toggle synchronization is performed bit 2 BSTALL: Buffer Stall Enable bit 1 = Buffer stall enabled; STALL handshake issued if a token is received that would use the BD in the given location (UOWN bit remains set, BD value is unchanged) 0 = Buffer stall disabled bit 1-0 BC9:BC8: Byte Count 9 and 8 bits The byte count bits represent the number of bytes that will be transmitted for an IN token or received during an OUT token. Together with BC<7:0>, the valid byte counts are 0-1023. Note 1: 2: 3: This bit must be initialized by the user to the desired value prior to enabling the USB module. This bit is ignored unless DTSEN = 1. If these bits are set, USB communication may not work. Hence, these bits should always be maintained as ‘0’. © 2008 Microchip Technology Inc. DS39760D-page 139 PIC18F2450/4450 14.4.1.3 BDnSTAT Register (SIE Mode) When the BD and its buffer are owned by the SIE, most of the bits in BDnSTAT take on a different meaning. The configuration is shown in Register 14-6. Once UOWN is set, any data or control settings previously written there by the user will be overwritten with data from the SIE. The BDnSTAT register is updated by the SIE with the token Packet Identifier (PID) which is stored in BDnSTAT<5:3>. The transfer count in the corresponding BDnCNT register is updated. Values that overflow the 8-bit register carry over to the two most significant digits of the count, stored in BDnSTAT<1:0>. 14.4.2 BD BYTE COUNT The byte count represents the total number of bytes that will be transmitted during an IN transfer. After an IN transfer, the SIE will return the number of bytes sent to the host. For an OUT transfer, the byte count represents the maximum number of bytes that can be received and stored in USB RAM. After an OUT transfer, the SIE will return the actual number of bytes received. If the number of bytes received exceeds the corresponding REGISTER 14-6: byte count, the data packet will be rejected and a NAK handshake will be generated. When this happens, the byte count will not be updated. The 10-bit byte count is distributed over two registers. The lower 8 bits of the count reside in the BDnCNT register. The upper two bits reside in BDnSTAT<1:0>. This represents a valid byte range of 0 to 1023. 14.4.3 BD ADDRESS VALIDATION The BD Address register pair contains the starting RAM address location for the corresponding endpoint buffer. For an endpoint starting location to be valid, it must fall in the range of the USB RAM, 400h to 4FFh. No mechanism is available in hardware to validate the BD address. If the value of the BD address does not point to an address in the USB RAM, or if it points to an address within another endpoint’s buffer, data is likely to be lost or overwritten. Similarly, overlapping a receive buffer (OUT endpoint) with a BD location in use can yield unexpected results. When developing USB applications, the user may want to consider the inclusion of software-based address validation in their code. BDnSTAT: BUFFER DESCRIPTOR n STATUS REGISTER (BD0STAT THROUGH BD63STAT), SIE MODE (DATA RETURNED BY THE SIDE TO THE MICROCONTROLLER) R/W-x U-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x UOWN — PID3 PID2 PID1 PID0 BC9 BC8 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 UOWN: USB Own bit 1 = The SIE owns the BD and its corresponding buffer bit 6 Reserved: Not written by the SIE bit 5-2 PID3:PID0: Packet Identifier bits The received token PID value of the last transfer (IN, OUT or SETUP transactions only). bit 1-0 BC9:BC8: Byte Count 9 and 8 bits These bits are updated by the SIE to reflect the actual number of bytes received on an OUT transfer and the actual number of bytes transmitted on an IN transfer. DS39760D-page 140 © 2008 Microchip Technology Inc. PIC18F2450/4450 14.4.4 PING-PONG BUFFERING An endpoint is defined to have a ping-pong buffer when it has two sets of BD entries: one set for an EVEN transfer and one set for an ODD transfer. This allows the CPU to process one BD while the SIE is processing the other BD. Double-buffering BDs in this way allows for maximum throughput to/from the USB. The USB module supports three modes of operation: • No ping-pong support • Ping-pong buffer support for OUT Endpoint 0 only • Ping-pong buffer support for all endpoints The ping-pong buffer settings are configured using the PPB1:PPB0 bits in the UCFG register. The USB module keeps track of the Ping-Pong Pointer individually for each endpoint. All pointers are initially reset to the EVEN BD when the module is enabled. After the completion of a transaction (UOWN cleared FIGURE 14-7: by the SIE), the pointer is toggled to the ODD BD. After the completion of the next transaction, the pointer is toggled back to the EVEN BD and so on. The EVEN/ODD status of the last transaction is stored in the PPBI bit of the USTAT register. The user can reset all Ping-Pong Pointers to EVEN using the PPBRST bit. Figure 14-7 shows the three different modes of operation and how USB RAM is filled with the BDs. BDs have a fixed relationship to a particular endpoint, depending on the buffering configuration. The mapping of BDs to endpoints is detailed in Table 14-4. This relationship also means that gaps may occur in the BDT if endpoints are not enabled contiguously. This theoretically means that the BDs for disabled endpoints could be used as buffer space. In practice, users should avoid using such spaces in the BDT unless a method of validating BD addresses is implemented. BUFFER DESCRIPTOR TABLE MAPPING FOR BUFFERING MODES PPB1:PPB0 = 00 No Ping-Pong Buffers PPB1:PPB0 = 01 Ping-Pong Buffer on EP0 OUT 400h 400h PPB1:PPB0 = 10 Ping-Pong Buffers on All EPs 400h EP0 OUT Descriptor EP0 OUT EVEN Descriptor EP0 OUT EVEN Descriptor EP0 IN Descriptor EP0 OUT ODD Descriptor EP0 OUT ODD Descriptor EP1 OUT Descriptor EP0 IN EVEN Descriptor EP0 IN Descriptor EP1 IN Descriptor EP0 IN ODD Descriptor EP1 OUT Descriptor EP1 OUT EVEN Descriptor EP1 IN Descriptor 47Fh Available as Data RAM EP1 IN ODD Descriptor Available as Data RAM 4FFh 4FFh Maximum Memory Used: 128 bytes Maximum BDs: 32 (BD0 to BD31) EP1 IN EVEN Descriptor EP15 IN Descriptor 483h Note: EP1 OUT ODD Descriptor EP15 IN Descriptor Maximum Memory Used: 132 bytes Maximum BDs: 33 (BD0 to BD32) 4FFh EP15 IN ODD Descriptor Maximum Memory Used: 256 bytes Maximum BDs: 64 (BD0 to BD63) Memory area not shown to scale. © 2008 Microchip Technology Inc. DS39760D-page 141 PIC18F2450/4450 TABLE 14-4: ASSIGNMENT OF BUFFER DESCRIPTORS FOR THE DIFFERENT BUFFERING MODES BDs Assigned to Endpoint Mode 0 (No Ping-Pong) Endpoint Mode 1 (Ping-Pong on EP0 OUT) Mode 2 (Ping-Pong on all EPs) Out In Out In Out In 0 0 1 0 (E), 1 (O) 2 0 (E), 1 (O) 2 (E), 3 (O) 1 2 3 3 4 4 (E), 5 (O) 6 (E), 7 (O) 2 4 5 5 6 8 (E), 9 (O) 10 (E), 11 (O) 3 6 7 7 8 12 (E), 13 (O) 14 (E), 15 (O) 4 8 9 9 10 16 (E), 17 (O) 18 (E), 19 (O) 5 10 11 11 12 20 (E), 21 (O) 22 (E), 23 (O) 6 12 13 13 14 24 (E), 25 (O) 26 (E), 27 (O) 7 14 15 15 16 28 (E), 29 (O) 30 (E), 31 (O) 8 16 17 17 18 32 (E), 33 (O) 34 (E), 35 (O) 9 18 19 19 20 36 (E), 37 (O) 38 (E), 39 (O) 10 20 21 21 22 40 (E), 41 (O) 42 (E), 43 (O) 11 22 23 23 24 44 (E), 45 (O) 46 (E), 47 (O) 12 24 25 25 26 48 (E), 49 (O) 50 (E), 51 (O) 13 26 27 27 28 52 (E), 53 (O) 54 (E), 55 (O) 14 28 29 29 30 56 (E), 57 (O) 58 (E), 59 (O) 15 30 31 31 32 60 (E), 61 (O) 62 (E), 63 (O) Legend: (E) = EVEN transaction buffer, (O) = ODD transaction buffer TABLE 14-5: SUMMARY OF USB BUFFER DESCRIPTOR TABLE REGISTERS Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 BDnSTAT(1) UOWN DTS(4) PID3(2) PID2(2) PID1(2) DTSEN(3) PID0(2) BSTALL(3) BC9 BC8 BDnCNT(1) Byte Count BDnADRL(1) Buffer Address Low BDnADRH(1) Buffer Address High Note 1: 2: 3: 4: For buffer descriptor registers, n may have a value of 0 to 63. For the sake of brevity, all 64 registers are shown as one generic prototype. All registers have indeterminate Reset values (xxxx xxxx). Bits 5 through 2 of the BDnSTAT register are used by the SIE to return PID3:PID0 values once the register is turned over to the SIE (UOWN bit is set). Once the registers have been under SIE control, the values written for DTSEN and BSTALL are no longer valid. Prior to turning the buffer descriptor over to the SIE (UOWN bit is cleared), bits 3 and 2 of the BDnSTAT register are used to configure the DTSEN and BSTALL settings. This bit is ignored unless DTSEN = 1. DS39760D-page 142 © 2008 Microchip Technology Inc. PIC18F2450/4450 14.5 USB Interrupts Figure 14-8 shows the interrupt logic for the USB module. There are two layers of interrupt registers in the USB module. The top level consists of overall USB status interrupts; these are enabled and flagged in the UIE and UIR registers, respectively. The second level consists of USB error conditions, which are enabled and flagged in the UEIR and UEIE registers. An interrupt condition in any of these triggers a USB Error Interrupt Flag (UERRIF) in the top level. The USB module can generate multiple interrupt conditions. To accommodate all of these interrupt sources, the module is provided with its own interrupt logic structure, similar to that of the microcontroller. USB interrupts are enabled with one set of control registers and trapped with a separate set of flag registers. All sources are funneled into a single USB interrupt request, USBIF (PIR2<5>), in the microcontroller’s interrupt logic. FIGURE 14-8: Interrupts may be used to trap routine events in a USB transaction. Figure 14-9 shows some common events within a USB frame and their corresponding interrupts. USB INTERRUPT LOGIC FUNNEL Second Level USB Interrupts (USB Error Conditions) Top Level USB Interrupts (USB Status Interrupts) UEIR (Flag) and UEIE (Enable) Registers UIR (Flag) and UIE (Enable) Registers SOFIF SOFIE BTSEF BTSEE TRNIF TRNIE BTOEF BTOEE USBIF IDLEIF IDLEIE DFN8EF DFN8EE UERRIF UERRIE CRC16EF CRC16EE STALLIF STALLIE CRC5EF CRC5EE PIDEF PIDEE ACTVIF ACTVIE URSTIF URSTIE FIGURE 14-9: EXAMPLE OF A USB TRANSACTION AND INTERRUPT EVENTS From Host From Host To Host SETUP Token Data ACK To Host From Host Data ACK From Host To Host Empty Data ACK From Host IN Token USB Reset URSTIF From Host Start-of-Frame (SOF) SOFIF OUT Token Set TRNIF Set TRNIF Set TRNIF Transaction Transaction Complete RESET SOF SETUP DATA SOF STATUS Differential Data Control Transfer(1) 1 ms Frame Note 1: The control transfer shown here is only an example showing events that can occur for every transaction. Typical control transfers will spread across multiple frames. © 2008 Microchip Technology Inc. DS39760D-page 143 PIC18F2450/4450 14.5.1 USB INTERRUPT STATUS REGISTER (UIR) When the USB module is in the Low-Power Suspend mode (UCON<1> = 1), the SIE does not get clocked. When in this state, the SIE cannot process packets, and therefore, cannot detect new interrupt conditions other than the Activity Detect Interrupt, Flag ACTVIF. The ACTVIF bit is typically used by USB firmware to detect when the microcontroller should bring the USB module out of the Low-Power Suspend mode (UCON<1> = 0). The USB Interrupt Status register (Register 14-7) contains the flag bits for each of the USB status interrupt sources. Each of these sources has a corresponding interrupt enable bit in the UIE register. All of the USB status flags are ORed together to generate the USBIF interrupt flag for the microcontroller’s interrupt funnel. Once an interrupt bit has been set by the SIE, it must be cleared by software by writing a ‘0’. The flag bits can also be set in software which can aid in firmware debugging. REGISTER 14-7: U-0 UIR: USB INTERRUPT STATUS REGISTER R/W-0 — SOFIF R/W-0 R/W-0 R/W-0 R/W-0 R-0 R/W-0 STALLIF IDLEIF(1) TRNIF(2) ACTVIF(3) UERRIF(4) URSTIF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 Unimplemented: Read as ‘0’ bit 6 SOFIF: Start-of-Frame Token Interrupt bit 1 = A Start-of-Frame token received by the SIE 0 = No Start-of-Frame token received by the SIE bit 5 STALLIF: A STALL Handshake Interrupt bit 1 = A STALL handshake was sent by the SIE 0 = A STALL handshake has not been sent bit 4 IDLEIF: Idle Detect Interrupt bit(1) 1 = Idle condition detected (constant Idle state of 3 ms or more) 0 = No Idle condition detected bit 3 TRNIF: Transaction Complete Interrupt bit(2) 1 = Processing of pending transaction is complete; read USTAT register for endpoint information 0 = Processing of pending transaction is not complete or no transaction is pending bit 2 ACTVIF: Bus Activity Detect Interrupt bit(3) 1 = Activity on the D+/D- lines was detected 0 = No activity detected on the D+/D- lines bit 1 UERRIF: USB Error Condition Interrupt bit(4) 1 = An unmasked error condition has occurred 0 = No unmasked error condition has occurred. bit 0 URSTIF: USB Reset Interrupt bit 1 = Valid USB Reset occurred; 00h is loaded into UADDR register 0 = No USB Reset has occurred Note 1: 2: 3: 4: Once an Idle state is detected, the user may want to place the USB module in Suspend mode. Clearing this bit will cause the USTAT FIFO to advance (valid only for IN, OUT and SETUP tokens). This bit is typically unmasked only following the detection of a UIDLE interrupt event. Only error conditions enabled through the UEIE register will set this bit. This bit is a status bit only and cannot be set or cleared by the user. DS39760D-page 144 © 2008 Microchip Technology Inc. PIC18F2450/4450 14.5.1.1 Bus Activity Detect Interrupt Bit (ACTVIF) The ACTVIF bit cannot be cleared immediately after the USB module wakes up from Suspend or while the USB module is suspended. A few clock cycles are required to synchronize the internal hardware state machine before the ACTVIF bit can be cleared by firmware. Clearing the ACTVIF bit before the internal hardware is synchronized may not have an effect on the value of ACTVIF. Additionally, if the USB module uses the clock from the 96 MHz PLL source, then after clearing the SUSPND bit, the USB module may not be immediately operational while waiting for the 96 MHz PLL to lock. The application code should clear the ACTVIF bit as shown in Example 14-1. EXAMPLE 14-1: CLEARING ACTVIF BIT (UIR<2>) Assembly: BCF UCON, SUSPND BTFSS BRA BCF BRA UIR, ACTVIF DONE UIR, ACTVIF LOOP LOOP: DONE C: UCONbits.SUSPND = 0; while (UIRbits.ACTVIF){UIRbits.ACTVIF = 0}; Only one ACTVIF interrupt is generated when resuming from the USB bus Idle condition. If user firmware clears the ACTVIF bit, the bit will not immediately become set again, even when there is continuous bus traffic. Bus traffic must cease long enough to generate another IDLEIF condition before another ACTVIF interrupt can be generated. © 2008 Microchip Technology Inc. DS39760D-page 145 PIC18F2450/4450 14.5.2 USB INTERRUPT ENABLE REGISTER (UIE) The USB Interrupt Enable register (Register 14-8) contains the enable bits for the USB status interrupt sources. Setting any of these bits will enable the respective interrupt source in the UIR register. REGISTER 14-8: The values in this register only affect the propagation of an interrupt condition to the microcontroller’s interrupt logic. The flag bits are still set by their interrupt conditions, allowing them to be polled and serviced without actually generating an interrupt. UIE: USB INTERRUPT ENABLE REGISTER U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — SOFIE STALLIE IDLEIE TRNIE ACTVIE UERRIE URSTIE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 Unimplemented: Read as ‘0’ bit 6 SOFIE: Start-of-Frame Token Interrupt Enable bit 1 = Start-of-Frame token interrupt enabled 0 = Start-of-Frame token interrupt disabled bit 5 STALLIE: STALL Handshake Interrupt Enable bit 1 = STALL interrupt enabled 0 = STALL interrupt disabled bit 4 IDLEIE: Idle Detect Interrupt Enable bit 1 = Idle detect interrupt enabled 0 = Idle detect interrupt disabled bit 3 TRNIE: Transaction Complete Interrupt Enable bit 1 = Transaction interrupt enabled 0 = Transaction interrupt disabled bit 2 ACTVIE: Bus Activity Detect Interrupt Enable bit 1 = Bus activity detect interrupt enabled 0 = Bus activity detect interrupt disabled bit 1 UERRIE: USB Error Interrupt Enable bit 1 = USB error interrupt enabled 0 = USB error interrupt disabled bit 0 URSTIE: USB Reset Interrupt Enable bit 1 = USB Reset interrupt enabled 0 = USB Reset interrupt disabled DS39760D-page 146 x = Bit is unknown © 2008 Microchip Technology Inc. PIC18F2450/4450 14.5.3 USB ERROR INTERRUPT STATUS REGISTER (UEIR) The USB Error Interrupt Status register (Register 14-9) contains the flag bits for each of the error sources within the USB peripheral. Each of these sources is controlled by a corresponding interrupt enable bit in the UEIE register. All of the USB error flags are ORed together to generate the USB Error Interrupt Flag (UERRIF) at the top level of the interrupt logic. REGISTER 14-9: Each error bit is set as soon as the error condition is detected. Thus, the interrupt will typically not correspond with the end of a token being processed. Once an interrupt bit has been set by the SIE, it must be cleared by software by writing a ‘0’. UEIR: USB ERROR INTERRUPT STATUS REGISTER R/C-0 U-0 U-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 BTSEF — — BTOEF DFN8EF CRC16EF CRC5EF PIDEF bit 7 bit 0 Legend: R = Readable bit C = Clearable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 BTSEF: Bit Stuff Error Flag bit 1 = A bit stuff error has been detected 0 = No bit stuff error bit 6-5 Unimplemented: Read as ‘0’ bit 4 BTOEF: Bus Turnaround Time-out Error Flag bit 1 = Bus turnaround time-out has occurred (more than 16 bit times of Idle from previous EOP elapsed) 0 = No bus turnaround time-out bit 3 DFN8EF: Data Field Size Error Flag bit 1 = The data field was not an integral number of bytes 0 = The data field was an integral number of bytes bit 2 CRC16EF: CRC16 Failure Flag bit 1 = The CRC16 failed 0 = The CRC16 passed bit 1 CRC5EF: CRC5 Host Error Flag bit 1 = The token packet was rejected due to a CRC5 error 0 = The token packet was accepted bit 0 PIDEF: PID Check Failure Flag bit 1 = PID check failed 0 = PID check passed © 2008 Microchip Technology Inc. DS39760D-page 147 PIC18F2450/4450 14.5.4 USB ERROR INTERRUPT ENABLE REGISTER (UEIE) As with the UIE register, the enable bits only affect the propagation of an interrupt condition to the microcontroller’s interrupt logic. The flag bits are still set by their interrupt conditions, allowing them to be polled and serviced without actually generating an interrupt. The USB Error Interrupt Enable register (Register 14-10) contains the enable bits for each of the USB error interrupt sources. Setting any of these bits will enable the respective error interrupt source in the UEIR register to propagate into the UERR bit at the top level of the interrupt logic. REGISTER 14-10: UEIE: USB ERROR INTERRUPT ENABLE REGISTER R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 BTSEE — — BTOEE DFN8EE CRC16EE CRC5EE PIDEE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 BTSEE: Bit Stuff Error Interrupt Enable bit 1 = Bit stuff error interrupt enabled 0 = Bit stuff error interrupt disabled bit 6-5 Unimplemented: Read as ‘0’ bit 4 BTOEE: Bus Turnaround Time-out Error Interrupt Enable bit 1 = Bus turnaround time-out error interrupt enabled 0 = Bus turnaround time-out error interrupt disabled bit 3 DFN8EE: Data Field Size Error Interrupt Enable bit 1 = Data field size error interrupt enabled 0 = Data field size error interrupt disabled bit 2 CRC16EE: CRC16 Failure Interrupt Enable bit 1 = CRC16 failure interrupt enabled 0 = CRC16 failure interrupt disabled bit 1 CRC5EE: CRC5 Host Error Interrupt Enable bit 1 = CRC5 host error interrupt enabled 0 = CRC5 host error interrupt disabled bit 0 PIDEE: PID Check Failure Interrupt Enable bit 1 = PID check failure interrupt enabled 0 = PID check failure interrupt disabled DS39760D-page 148 x = Bit is unknown © 2008 Microchip Technology Inc. PIC18F2450/4450 14.6 USB Power Modes Many USB applications will likely have several different sets of power requirements and configuration. The most common power modes encountered are Bus Power Only, Self-Power Only and Dual Power with Self-Power Dominance. The most common cases are presented here. 14.6.1 In order to meet compliance specifications, the USB module (and the D+ or D- pull-up resistor) should not be enabled until the host actively drives VBUS high. One of the I/O pins may be used for this purpose. The application should never source any current onto the 5V VBUS pin of the USB cable. FIGURE 14-11: BUS POWER ONLY SELF-POWER ONLY Attach Sense VBUS ~5V In Bus Power Only mode, all power for the application is drawn from the USB (Figure 14-10). This is effectively the simplest power method for the device. VSELF ~5V In order to meet the inrush current requirements of the USB 2.0 specifications, the total effective capacitance appearing across VBUS and ground must be no more than 10 μF; otherwise, some kind of inrush limiting is required. For more details, see Section 7.2.4 of the USB 2.0 specification. According to the USB 2.0 specification, all USB devices must also support a Low-Power Suspend mode. In the USB Suspend mode, devices must consume no more than 500 A (or 2.5 mA for high-powered devices that are capable of remote wake-up) from the 5V VBUS line of the USB cable. The host signals the USB device to enter the Suspend mode by stopping all USB traffic to that device for more than 3 ms. This condition will set the IDLEIF bit in the UIR register. During the USB Suspend mode, the D+ or D- pull-up resistor must remain active, which will consume some of the allowed suspend current: 500A/2.5 mA budget. I/O pin 100 kΩ VDD VUSB 100 kΩ VSS 14.6.3 DUAL POWER WITH SELF-POWER DOMINANCE Some applications may require a dual power option. This allows the application to use internal power primarily, but switch to power from the USB when no internal power is available. Figure 14-12 shows a simple Dual Power with Self-Power Dominance example, which automatically switches between Self-Power Only and USB Bus Power Only modes. FIGURE 14-12: DUAL POWER EXAMPLE 100 kΩ Attach Sense FIGURE 14-10: BUS POWER ONLY VBUS ~5V VBUS ~5V VDD VUSB 100 kΩ VSELF ~5V I/O pin VDD VUSB VSS VSS 14.6.2 SELF-POWER ONLY In Self-Power Only mode, the USB application provides its own power, with very little power being pulled from the USB. Figure 14-11 shows an example. Note that an attach indication is added to show when the USB has been connected and the host is actively powering VBUS. © 2008 Microchip Technology Inc. Dual power devices must also meet all of the special requirements for inrush current and Suspend mode current, and must not enable the USB module until VBUS is driven high. For descriptions of those requirements, see Section 14.6.1 “Bus Power Only” and Section 14.6.2 “Self-Power Only”. Additionally, dual power devices must never source current onto the 5V VUSB pin of the USB cable. Note: Users should keep in mind the limits for devices drawing power from the USB. According to USB Specification 2.0, this cannot exceed 100 mA per low-power device or 500 mA per high-power device. DS39760D-page 149 PIC18F2450/4450 14.7 Oscillator 14.8 The USB module has specific clock requirements. For full-speed operation, the clock source must be 48 MHz. Even so, the microcontroller core and other peripherals are not required to run at that clock speed or even from the same clock source. Available clocking options are described in detail in Section 2.3 “Oscillator Settings for USB”. TABLE 14-6: Name INTCON USB Firmware and Drivers Microchip provides a number of application-specific resources, such as USB firmware and driver support. Refer to www.microchip.com for the latest firmware and driver support. REGISTERS ASSOCIATED WITH USB MODULE OPERATION(1) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Details on Page: GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 IPR2 OSCFIP — USBIP — — HLVDIP — — 51 PIR2 OSCFIF — USBIF — — HLVDIF — — 51 PIE2 OSCFIE — USBIE — — HLVDIE — — 51 UCON — PPBRST SE0 PKTDIS USBEN RESUME SUSPND — 52 UCFG UTEYE UOEMON — UPUEN UTRDIS FSEN PPB1 PPB0 52 USTAT — ENDP3 ENDP2 ENDP1 ENDP0 DIR PPBI — 52 UADDR — ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0 52 UFRML FRM7 FRM6 FRM5 FRM4 FRM3 FRM2 FRM1 FRM0 52 UFRMH — — — — — FRM10 FRM9 FRM8 52 UIR — SOFIF STALLIF IDLEIF TRNIF ACTVIF UERRIF URSTIF 52 UIE — SOFIE STALLIE IDLEIE TRNIE ACTVIE UERRIE URSTIE 52 UEIR BTSEF — — BTOEF DFN8EF CRC16EF CRC5EF PIDEF 52 UEIE BTSEE — — BTOEE DFN8EE CRC16EE CRC5EE PIDEE 52 UEP0 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 52 UEP1 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 52 UEP2 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 52 UEP3 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 52 UEP4 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 52 UEP5 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 52 UEP6 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 52 UEP7 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 52 UEP8 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 52 UEP9 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 52 UEP10 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 51 UEP11 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 51 UEP12 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 51 UEP13 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 51 UEP14 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 51 UEP15 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL 51 Legend: Note 1: — = unimplemented, read as ‘0’. Shaded cells are not used by the USB module. This table includes only those hardware mapped SFRs located in Bank 15 of the data memory space. The Buffer Descriptor registers, which are mapped into Bank 4 and are not true SFRs, are listed separately in Table 14-5. DS39760D-page 150 © 2008 Microchip Technology Inc. PIC18F2450/4450 14.9 Overview of USB 14.9.3 This section presents some of the basic USB concepts and useful information necessary to design a USB device. Although much information is provided in this section, there is a plethora of information provided within the USB specifications and class specifications. Thus, the reader is encouraged to refer to the USB specifications for more information (www.usb.org). If you are very familiar with the details of USB, then this section serves as a basic, high-level refresher of USB. 14.9.1 LAYERED FRAMEWORK USB device functionality is structured into a layered framework graphically shown in Figure 14-13. Each level is associated with a functional level within the device. The highest layer, other than the device, is the configuration. A device may have multiple configurations. For example, a particular device may have multiple power requirements based on Self-Power Only or Bus Power Only modes. For each configuration, there may be multiple interfaces. Each interface could support a particular mode of that configuration. Below the interface is the endpoint(s). Data is directly moved at this level. There can be as many as 16 bidirectional endpoints. Endpoint 0 is always a control endpoint and by default, when the device is on the bus, Endpoint 0 must be available to configure the device. 14.9.2 TRANSFERS There are four transfer types defined in the USB specification. • Isochronous: This type provides a transfer method for large amounts of data (up to 1023 bytes) with timely delivery ensured; however, the data integrity is not ensured. This is good for streaming applications where small data loss is not critical, such as audio. • Bulk: This type of transfer method allows for large amounts of data to be transferred with ensured data integrity; however, the delivery timeliness is not ensured. • Interrupt: This type of transfer provides for ensured timely delivery for small blocks of data; plus data integrity is ensured. • Control: This type provides for device setup control. While full-speed devices support all transfer types, low-speed devices are limited to interrupt and control transfers only. 14.9.4 POWER Power is available from the Universal Serial Bus. The USB specification defines the bus power requirements. Devices may either be self-powered or bus powered. Self-powered devices draw power from an external source, while bus powered devices use power supplied from the bus. FRAMES Information communicated on the bus is grouped into 1 ms time slots, referred to as frames. Each frame can contain many transactions to various devices and endpoints. Figure 14-9 shows an example of a transaction within a frame. FIGURE 14-13: USB LAYERS Device To Other Configurations (if any) Configuration To Other Interfaces (if any) Interface Interface Endpoint Endpoint © 2008 Microchip Technology Inc. Endpoint Endpoint Endpoint DS39760D-page 151 PIC18F2450/4450 The USB specification limits the power taken from the bus. Each device is ensured 100 mA at approximately 5V (one-unit load). Additional power may be requested, up to a maximum of 500 mA. Note that power above a oneunit load is a request and the host or hub is not obligated to provide the extra current. Thus, a device capable of consuming more than a one-unit load must be able to maintain a low-power configuration of a one-unit load or less, if necessary. 14.9.6.2 The USB specification also defines a Suspend mode. In this situation, current must be limited to 500 μA, averaged over 1 second. A device must enter a Suspend state after 3 ms of inactivity (i.e., no SOF tokens for 3 ms). A device entering Suspend mode must drop current consumption within 10 ms after Suspend mode. Likewise, when signaling a wake-up, the device must signal a wake-up within 10 ms of drawing current above the Suspend limit. The interface descriptor details the number of endpoints used in this interface, as well as the class of the interface. There may be more than one interface for a configuration. 14.9.5 ENUMERATION When the device is initially attached to the bus, the host enters an enumeration process in an attempt to identify the device. Essentially, the host interrogates the device, gathering information such as power consumption, data rates and sizes, protocol and other descriptive information; descriptors contain this information. A typical enumeration process would be as follows: 1. 2. 3. 4. 5. 6. 7. 8. USB Reset: Reset the device. Thus, the device is not configured and does not have an address (address 0). Get Device Descriptor: The host requests a small portion of the device descriptor. USB Reset: Reset the device again. Set Address: The host assigns an address to the device. Get Device Descriptor: The host retrieves the device descriptor, gathering info such as manufacturer, type of device, maximum control packet size. Get configuration descriptors. Get any other descriptors. Set a configuration. The exact enumeration process depends on the host. 14.9.6 DESCRIPTORS There are eight different standard descriptor types of which five are most important for this device. 14.9.6.1 Device Descriptor The device descriptor provides general information, such as manufacturer, product number, serial number, the class of the device and the number of configurations. There is only one device descriptor. DS39760D-page 152 Configuration Descriptor The configuration descriptor provides information on the power requirements of the device and how many different interfaces are supported when in this configuration. There may be more than one configuration for a device (i.e., low-power and high-power configurations). 14.9.6.3 14.9.6.4 Interface Descriptor Endpoint Descriptor The endpoint descriptor identifies the transfer type (Section 14.9.3 “Transfers”) and direction, as well as some other specifics for the endpoint. There may be many endpoints in a device and endpoints may be shared in different configurations. 14.9.6.5 String Descriptor Many of the previous descriptors reference one or more string descriptors. String descriptors provide human readable information about the layer (Section 14.9.1 “Layered Framework”) they describe. Often these strings show up in the host to help the user identify the device. String descriptors are generally optional to save memory and are encoded in a unicode format. 14.9.7 BUS SPEED Each USB device must indicate its bus presence and speed to the host. This is accomplished through a 1.5 kΩ resistor which is connected to the bus at the time of the attachment event. Depending on the speed of the device, the resistor either pulls up the D+ or D- line to 3.3V. For a lowspeed device, the pull-up resistor is connected to the D- line. For a full-speed device, the pull-up resistor is connected to the D+ line. 14.9.8 CLASS SPECIFICATIONS AND DRIVERS USB specifications include class specifications which operating system vendors optionally support. Examples of classes include Audio, Mass Storage, Communications and Human Interface (HID). In most cases, a driver is required at the host side to ‘talk’ to the USB device. In custom applications, a driver may need to be developed. Fortunately, drivers are available for most common host systems for the most common classes of devices. Thus, these drivers can be reused. © 2008 Microchip Technology Inc. PIC18F2450/4450 15.0 ENHANCED UNIVERSAL SYNCHRONOUS RECEIVER TRANSMITTER (EUSART) The Universal Synchronous Asynchronous Receiver Transmitter (USART) module is one of the two serial I/O modules. (USART is also known as a Serial Communications Interface or SCI.) The USART can be configured as a full-duplex asynchronous system that can communicate with peripheral devices, such as CRT terminals and personal computers. It can also be configured as a half-duplex synchronous system that can communicate with peripheral devices, such as A/D or D/A integrated circuits, serial EEPROMs and so on. The Enhanced Universal Synchronous Receiver Transmitter (EUSART) module implements additional features, including Automatic Baud Rate Detection (ABD) and calibration, automatic wake-up on Sync Break reception and 12-bit Break character transmit. These features make it ideally suited for use in Local Interconnect Network bus (LIN bus) systems. The pins of the Enhanced USART are multiplexed with PORTC. In order to configure RC6/TX/CK and RC7/RX/DT as an EUSART: • bit SPEN (RCSTA<7>) must be set (= 1) • bit TRISC<7> must be set (= 1) • bit TRISC<6> must be cleared (= 0) for Asynchronous and Synchronous Master modes or set (= 1) for Synchronous Slave mode Note: The EUSART control will automatically reconfigure the pin from input to output as needed. The operation of the Enhanced USART module is controlled through three registers: • Transmit Status and Control (TXSTA) • Receive Status and Control (RCSTA) • Baud Rate Control (BAUDCON) These are detailed on the following pages in Register 15-1, Register 15-2 and Register 15-3, respectively. The EUSART can be configured in the following modes: • Asynchronous (full-duplex) with: - Auto-wake-up on character reception - Auto-baud calibration - 12-bit Break character transmission • Synchronous – Master (half-duplex) with selectable clock polarity • Synchronous – Slave (half-duplex) with selectable clock polarity © 2008 Microchip Technology Inc. DS39760D-page 153 PIC18F2450/4450 REGISTER 15-1: TXSTA: TRANSMIT STATUS AND CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R-1 R/W-0 CSRC TX9 TXEN(1) SYNC SENDB BRGH TRMT TX9D bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 CSRC: Clock Source Select bit Asynchronous mode: Don’t care. Synchronous mode: 1 = Master mode (clock generated internally from BRG) 0 = Slave mode (clock from external source) bit 6 TX9: 9-Bit Transmit Enable bit 1 = Selects 9-bit transmission 0 = Selects 8-bit transmission bit 5 TXEN: Transmit Enable bit(1) 1 = Transmit enabled 0 = Transmit disabled bit 4 SYNC: EUSART Mode Select bit 1 = Synchronous mode 0 = Asynchronous mode bit 3 SENDB: Send Break Character bit Asynchronous mode: 1 = Send Sync Break on next transmission (cleared by hardware upon completion) 0 = Sync Break transmission completed Synchronous mode: Don’t care. bit 2 BRGH: High Baud Rate Select bit Asynchronous mode: 1 = High speed 0 = Low speed Synchronous mode: Unused in this mode. bit 1 TRMT: Transmit Shift Register Status bit 1 = TSR empty 0 = TSR full bit 0 TX9D: 9th bit of Transmit Data Can be address/data bit or a parity bit. Note 1: SREN/CREN overrides TXEN in Sync mode with the exception that SREN has no effect in Synchronous Slave mode. DS39760D-page 154 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 15-2: RCSTA: RECEIVE STATUS AND CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-x SPEN RX9 SREN CREN ADDEN FERR OERR RX9D bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 SPEN: Serial Port Enable bit 1 = Serial port enabled (configures RX/DT and TX/CK pins as serial port pins) 0 = Serial port disabled (held in Reset) bit 6 RX9: 9-Bit Receive Enable bit 1 = Selects 9-bit reception 0 = Selects 8-bit reception bit 5 SREN: Single Receive Enable bit Asynchronous mode: Don’t care. Synchronous mode – Master: 1 = Enables single receive 0 = Disables single receive This bit is cleared after reception is complete. Synchronous mode – Slave: Don’t care. bit 4 CREN: Continuous Receive Enable bit Asynchronous mode: 1 = Enables receiver 0 = Disables receiver Synchronous mode: 1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN) 0 = Disables continuous receive bit 3 ADDEN: Address Detect Enable bit Asynchronous mode 9-bit (RX9 = 1): 1 = Enables address detection, enables interrupt and loads the receive buffer when RSR<8> is set 0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit Asynchronous mode 8-bit (RX9 = 0): Don’t care. bit 2 FERR: Framing Error bit 1 = Framing error (can be updated by reading RCREG register and receiving next valid byte) 0 = No framing error bit 1 OERR: Overrun Error bit 1 = Overrun error (can be cleared by clearing bit CREN) 0 = No overrun error bit 0 RX9D: 9th bit of Received Data This can be address/data bit or a parity bit and must be calculated by user firmware. © 2008 Microchip Technology Inc. DS39760D-page 155 PIC18F2450/4450 REGISTER 15-3: BAUDCON: BAUD RATE CONTROL REGISTER R/W-0 R-1 U-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 ABDOVF: Auto-Baud Acquisition Rollover Status bit 1 = A BRG rollover has occurred during Auto-Baud Rate Detect mode (must be cleared in software) 0 = No BRG rollover has occurred bit 6 RCIDL: Receive Operation Idle Status bit 1 = Receive operation is Idle 0 = Receive operation is active bit 5 Unimplemented: Read as ‘0’ bit 4 SCKP: Synchronous Clock Polarity Select bit Asynchronous mode: Unused in this mode. Synchronous mode: 1 = Idle state for clock (CK) is a high level 0 = Idle state for clock (CK) is a low level bit 3 BRG16: 16-Bit Baud Rate Register Enable bit 1 = 16-bit Baud Rate Generator – SPBRGH and SPBRG 0 = 8-bit Baud Rate Generator – SPBRG only (Compatible mode), SPBRGH value ignored bit 2 Unimplemented: Read as ‘0’ bit 1 WUE: Wake-up Enable bit Asynchronous mode: 1 = EUSART will continue to sample the RX pin – interrupt generated on falling edge; bit cleared in hardware on following rising edge 0 = RX pin not monitored or rising edge detected Synchronous mode: Unused in this mode. bit 0 ABDEN: Auto-Baud Detect Enable bit Asynchronous mode: 1 = Enable baud rate measurement on the next character. Requires reception of a Sync field (55h); cleared in hardware upon completion. 0 = Baud rate measurement disabled or completed Synchronous mode: Unused in this mode. DS39760D-page 156 © 2008 Microchip Technology Inc. PIC18F2450/4450 15.1 Baud Rate Generator (BRG) The BRG is a dedicated, 8-bit or 16-bit generator that supports both the Asynchronous and Synchronous modes of the EUSART. By default, the BRG operates in 8-bit mode. Setting the BRG16 bit (BAUDCON<3>) selects 16-bit mode. The SPBRGH:SPBRG register pair controls the period of a free-running timer. In Asynchronous mode, bits BRGH (TXSTA<2>) and BRG16 (BAUDCON<3>) also control the baud rate. In Synchronous mode, BRGH is ignored. Table 15-1 shows the formula for computation of the baud rate for different EUSART modes which only apply in Master mode (internally generated clock). Given the desired baud rate and FOSC, the nearest integer value for the SPBRGH:SPBRG registers can be calculated using the formulas in Table 15-1. From this, the error in baud rate can be determined. An example calculation is shown in Example 15-1. Typical baud rates and error values for the various Asynchronous modes are shown in Table 15-2. It may be advantageous to use TABLE 15-1: Writing a new value to the SPBRGH:SPBRG registers causes the BRG timer to be reset (or cleared). This ensures the BRG does not wait for a timer overflow before outputting the new baud rate. 15.1.1 OPERATION IN POWER-MANAGED MODES The device clock is used to generate the desired baud rate. When one of the power-managed modes is entered, the new clock source may be operating at a different frequency. This may require an adjustment to the value in the SPBRG register pair. 15.1.2 SAMPLING The data on the RX pin is sampled three times by a majority detect circuit to determine if a high or a low level is present at the RX pin. BAUD RATE FORMULAS Configuration Bits SYNC the high baud rate (BRGH = 1) or the 16-bit BRG to reduce the baud rate error, or achieve a slow baud rate for a fast oscillator frequency. BRG16 BRGH BRG/EUSART Mode 0 0 0 8-Bit/Asynchronous 0 0 1 8-Bit/Asynchronous 0 1 0 16-Bit/Asynchronous 0 1 1 16-Bit/Asynchronous 1 0 x 8-Bit/Synchronous 1 1 x 16-Bit/Synchronous Legend: x = Don’t care, n = Value of SPBRGH:SPBRG register pair © 2008 Microchip Technology Inc. Baud Rate Formula FOSC/[64 (n + 1)] FOSC/[16 (n + 1)] FOSC/[4 (n + 1)] DS39760D-page 157 PIC18F2450/4450 EXAMPLE 15-1: CALCULATING BAUD RATE ERROR For a device with FOSC of 16 MHz, desired baud rate of 9600, Asynchronous mode, 8-bit BRG: Desired Baud Rate = FOSC/(64 ([SPBRGH:SPBRG] + 1) Solving for SPBRGH:SPBRG: X = ((FOSC/Desired Baud Rate)/64) – 1 = ((16000000/9600)/64) – 1 = [25.042] = 25 Calculated Baud Rate = 16000000/(64 (25 + 1)) = 9615 Error = (Calculated Baud Rate – Desired Baud Rate)/Desired Baud Rate = (9615 – 9600)/9600 = 0.16% TABLE 15-2: Name REGISTERS ASSOCIATED WITH BAUD RATE GENERATOR Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TXSTA RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR BAUDCON ABDOVF RCIDL — SCKP BRG16 — WUE SPBRGH EUSART Baud Rate Generator Register High Byte SPBRG EUSART Baud Rate Generator Register Low Byte Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the BRG. DS39760D-page 158 Bit 0 TX9D RX9D ABDEN Reset Values on Page: 51 51 51 50 50 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 15-3: BAUD RATES FOR ASYNCHRONOUS MODES SYNC = 0, BRGH = 0, BRG16 = 0 BAUD RATE (K) FOSC = 40.000 MHz FOSC = 20.000 MHz SPBRG value Actual Rate (K) SPBRG value FOSC = 10.000 MHz Actual Rate (K) SPBRG value FOSC = 8.000 MHz Actual Rate (K) SPBRG value Actual Rate (K) % Error 0.3 — — — — — — — — — — — — 1.2 — — — 1.221 1.73 255 1.202 0.16 129 1.201 -0.16 103 2.4 2.441 1.73 255 2.404 0.16 129 2.404 0.16 64 2.403 -0.16 51 9.6 9.615 0.16 64 9.766 1.73 31 9.766 1.73 15 9.615 -0.16 12 19.2 19.531 1.73 31 19.531 1.73 15 19.531 1.73 7 — — — 57.6 56.818 -1.36 10 62.500 8.51 4 52.083 -9.58 2 — — — 115.2 125.000 8.51 4 104.167 -9.58 2 78.125 -32.18 1 — — — (decimal) % Error (decimal) % Error (decimal) % Error (decimal) SYNC = 0, BRGH = 0, BRG16 = 0 BAUD RATE (K) FOSC = 4.000 MHz FOSC = 2.000 MHz FOSC = 1.000 MHz (decimal) Actual Rate (K) 0.16 207 0.300 -0.16 103 0.300 -0.16 51 0.16 51 1.201 -0.16 25 1.201 -0.16 12 2.404 0.16 25 2.403 -0.16 12 — — — 9.6 8.929 -6.99 6 — — — — — — 19.2 20.833 8.51 2 — — — — — — Actual Rate (K) % Error 0.3 0.300 1.2 1.202 2.4 SPBRG value % Error (decimal) Actual Rate (K) % Error SPBRG value SPBRG value (decimal) 57.6 62.500 8.51 0 — — — — — — 115.2 62.500 -45.75 0 — — — — — — SYNC = 0, BRGH = 1, BRG16 = 0 BAUD RATE (K) FOSC = 40.000 MHz FOSC = 20.000 MHz (decimal) Actual Rate (K) % Error — — — — — — — — — 9.766 1.73 255 Actual Rate (K) % Error 0.3 — 1.2 — 2.4 9.6 SPBRG value FOSC = 10.000 MHz (decimal) Actual Rate (K) % Error — — — — — — — — — 9.615 0.16 FOSC = 8.000 MHz (decimal) Actual Rate (K) % Error — — — — — — — — — 2.441 1.73 255 2.403 -0.16 207 129 9.615 0.16 64 9.615 -0.16 51 25 SPBRG value SPBRG value SPBRG value (decimal) — 19.2 19.231 0.16 129 19.231 0.16 64 19.531 1.73 31 19.230 -0.16 57.6 58.140 0.94 42 56.818 -1.36 21 56.818 -1.36 10 55.555 3.55 8 115.2 113.636 -1.36 21 113.636 -1.36 10 125.000 8.51 4 — — — SYNC = 0, BRGH = 1, BRG16 = 0 BAUD RATE (K) FOSC = 4.000 MHz Actual Rate (K) % Error FOSC = 2.000 MHz SPBRG value (decimal) Actual Rate (K) % Error SPBRG value (decimal) FOSC = 1.000 MHz Actual Rate (K) % Error SPBRG value (decimal) 0.3 — — — — — — 0.300 -0.16 207 1.2 1.202 0.16 207 1.201 -0.16 103 1.201 -0.16 51 2.4 2.404 0.16 103 2.403 -0.16 51 2.403 -0.16 25 9.6 9.615 0.16 25 9.615 -0.16 12 — — — 19.2 19.231 0.16 12 — — — — — — 57.6 62.500 8.51 3 — — — — — — 115.2 125.000 8.51 1 — — — — — — © 2008 Microchip Technology Inc. DS39760D-page 159 PIC18F2450/4450 TABLE 15-3: BAUD RATES FOR ASYNCHRONOUS MODES (CONTINUED) SYNC = 0, BRGH = 0, BRG16 = 1 BAUD RATE (K) FOSC = 40.000 MHz Actual Rate (K) % Error FOSC = 20.000 MHz SPBRG value (decimal) Actual Rate (K) % Error FOSC = 10.000 MHz (decimal) Actual Rate (K) SPBRG value % Error FOSC = 8.000 MHz (decimal) Actual Rate (K) % Error SPBRG value SPBRG value (decimal) 0.3 0.300 0.00 8332 0.300 0.02 4165 0.300 0.02 2082 0.300 -0.04 1.2 1.200 0.02 2082 1.200 -0.03 1041 1.200 -0.03 520 1.201 -0.16 1665 415 2.4 2.402 0.06 1040 2.399 -0.03 520 2.404 0.16 259 2.403 -0.16 207 9.6 9.615 0.16 259 9.615 0.16 129 9.615 0.16 64 9.615 -0.16 51 25 19.2 19.231 0.16 129 19.231 0.16 64 19.531 1.73 31 19.230 -0.16 57.6 58.140 0.94 42 56.818 -1.36 21 56.818 -1.36 10 55.555 3.55 8 115.2 113.636 -1.36 21 113.636 -1.36 10 125.000 8.51 4 — — — SYNC = 0, BRGH = 0, BRG16 = 1 BAUD RATE (K) FOSC = 4.000 MHz FOSC = 2.000 MHz (decimal) Actual Rate (K) % Error 0.04 832 0.300 0.16 207 1.201 2.404 0.16 103 9.6 9.615 0.16 19.2 19.231 57.6 62.500 115.2 125.000 FOSC = 1.000 MHz (decimal) Actual Rate (K) % Error -0.16 415 0.300 -0.16 -0.16 103 1.201 -0.16 51 2.403 -0.16 51 2.403 -0.16 25 25 9.615 -0.16 12 — — — 0.16 12 — — — — — — 8.51 3 — — — — — — 8.51 1 — — — — — — Actual Rate (K) % Error 0.3 0.300 1.2 1.202 2.4 SPBRG value SPBRG value SPBRG value (decimal) 207 SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1 BAUD RATE (K) FOSC = 40.000 MHz FOSC = 20.000 MHz (decimal) Actual Rate (K) % Error 0.00 33332 0.300 0.00 8332 1.200 0.02 4165 Actual Rate (K) % Error 0.3 0.300 1.2 1.200 2.4 2.400 SPBRG value FOSC = 10.000 MHz (decimal) Actual Rate (K) % Error 0.00 16665 0.300 0.02 4165 1.200 2.400 0.02 2082 2.402 SPBRG value FOSC = 8.000 MHz (decimal) Actual Rate (K) % Error 0.00 8332 0.300 -0.01 6665 0.02 2082 1.200 -0.04 1665 0.06 1040 2.400 -0.04 832 SPBRG value SPBRG value (decimal) 9.6 9.606 0.06 1040 9.596 -0.03 520 9.615 0.16 259 9.615 -0.16 207 19.2 19.193 -0.03 520 19.231 0.16 259 19.231 0.16 129 19.230 -0.16 103 57.6 57.803 0.35 172 57.471 -0.22 86 58.140 0.94 42 57.142 0.79 34 115.2 114.943 -0.22 86 116.279 0.94 42 113.636 -1.36 21 117.647 -2.12 16 SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1 BAUD RATE (K) 0.3 1.2 FOSC = 4.000 MHz Actual Rate (K) % Error 0.300 1.200 0.01 0.04 FOSC = 2.000 MHz (decimal) Actual Rate (K) % Error 3332 832 0.300 1.201 -0.04 -0.16 SPBRG value FOSC = 1.000 MHz (decimal) Actual Rate (K) % Error 1665 415 0.300 1.201 -0.04 -0.16 832 207 SPBRG value SPBRG value (decimal) 2.4 2.404 0.16 415 2.403 -0.16 207 2.403 -0.16 103 9.6 9.615 0.16 103 9.615 -0.16 51 9.615 -0.16 25 19.2 19.231 0.16 51 19.230 -0.16 25 19.230 -0.16 12 57.6 58.824 2.12 16 55.555 3.55 8 — — — 115.2 111.111 -3.55 8 — — — — — — DS39760D-page 160 © 2008 Microchip Technology Inc. PIC18F2450/4450 15.1.3 AUTO-BAUD RATE DETECT The Enhanced USART module supports the automatic detection and calibration of baud rate. This feature is active only in Asynchronous mode and while the WUE bit is clear. While the ABD sequence takes place, the EUSART state machine is held in Idle. The RCIF interrupt is set once the fifth rising edge on RX is detected. The value in the RCREG needs to be read to clear the RCIF interrupt. The contents of RCREG should be discarded. The automatic baud rate measurement sequence (Figure 15-1) begins whenever a Start bit is received and the ABDEN bit is set. The calculation is self-averaging. Note 1: If the WUE bit is set with the ABDEN bit, Auto-Baud Rate Detection will occur on the byte following the Break character. In the Auto-Baud Rate Detect (ABD) mode, the clock to the BRG is reversed. Rather than the BRG clocking the incoming RX signal, the RX signal is timing the BRG. In ABD mode, the internal Baud Rate Generator is used as a counter to time the bit period of the incoming serial byte stream. 2: It is up to the user to determine that the incoming character baud rate is within the range of the selected BRG clock source. Some combinations of oscillator frequency and EUSART baud rates are not possible due to bit error rates. Overall system timing and communication baud rates must be taken into consideration when using the Auto-Baud Rate Detection feature. Once the ABDEN bit is set, the state machine will clear the BRG and look for a Start bit. The Auto-Baud Rate Detection must receive a byte with the value 55h (ASCII “U”, which is also the LIN bus Sync character) in order to calculate the proper bit rate. The measurement is taken over both a low and a high bit time in order to minimize any effects caused by asymmetry of the incoming signal. After a Start bit, the SPBRG begins counting up, using the preselected clock source on the first rising edge of RX. After eight bits on the RX pin, or the fifth rising edge, an accumulated value totalling the proper BRG period is left in the SPBRGH:SPBRG register pair. Once the 5th edge is seen (this should correspond to the Stop bit), the ABDEN bit is automatically cleared. If a rollover of the BRG occurs (an overflow from FFFFh to 0000h), the event is trapped by the ABDOVF status bit (BAUDCON<7>). It is set in hardware by BRG rollovers and can be set or cleared by the user in software. ABD mode remains active after rollover events and the ABDEN bit remains set (Figure 15-2). While calibrating the baud rate period, the BRG registers are clocked at 1/8th the preconfigured clock rate. Note that the BRG clock will be configured by the BRG16 and BRGH bits. Independent of the BRG16 bit setting, both the SPBRG and SPBRGH will be used as a 16-bit counter. This allows the user to verify that no carry occurred for 8-bit modes by checking for 00h in the SPBRGH register. Refer to Table 15-4 for counter clock rates to the BRG. © 2008 Microchip Technology Inc. TABLE 15-4: BRG COUNTER CLOCK RATES BRG16 BRGH BRG Counter Clock 0 0 FOSC/512 0 1 FOSC/128 1 0 FOSC/128 1 FOSC/32 1 Note: 15.1.3.1 During the ABD sequence, SPBRG and SPBRGH are both used as a 16-bit counter, independent of the BRG16 setting. ABD and EUSART Transmission Since the BRG clock is reversed during ABD acquisition, the EUSART transmitter cannot be used during ABD. This means that whenever the ABDEN bit is set, TXREG cannot be written to. Users should also ensure that ABDEN does not become set during a transmit sequence. Failing to do this may result in unpredictable EUSART operation. DS39760D-page 161 PIC18F2450/4450 FIGURE 15-1: BRG Value AUTOMATIC BAUD RATE CALCULATION XXXXh RX pin 0000h 001Ch Start Edge #1 bit 1 bit 0 Edge #2 bit 3 bit 2 Edge #3 bit 5 bit 4 Edge #4 bit 7 bit 6 Edge #5 Stop bit BRG Clock Auto-Cleared Set by User ABDEN bit RCIF bit (Interrupt) Read RCREG SPBRG XXXXh 1Ch SPBRGH XXXXh 00h Note: The ABD sequence requires the EUSART module to be configured in Asynchronous mode and WUE = 0. FIGURE 15-2: BRG OVERFLOW SEQUENCE BRG Clock ABDEN bit RX pin Start bit 0 ABDOVF bit FFFFh BRG Value DS39760D-page 162 XXXXh 0000h 0000h © 2008 Microchip Technology Inc. PIC18F2450/4450 15.2 EUSART Asynchronous Mode Once the TXREG register transfers the data to the TSR register (occurs in one TCY), the TXREG register is empty and the TXIF flag bit (PIR1<4>) is set. This interrupt can be enabled or disabled by setting or clearing the interrupt enable bit, TXIE (PIE1<4>). TXIF will be set regardless of the state of TXIE; it cannot be cleared in software. TXIF is also not cleared immediately upon loading TXREG but becomes valid in the second instruction cycle following the load instruction. Polling TXIF immediately following a load of TXREG will return invalid results. The Asynchronous mode of operation is selected by clearing the SYNC bit (TXSTA<4>). In this mode, the EUSART uses the standard Non-Return-to-Zero (NRZ) format (one Start bit, eight or nine data bits and one Stop bit). The most common data format is eight bits. An on-chip dedicated 8-bit/16-bit Baud Rate Generator can be used to derive standard baud rate frequencies from the oscillator. The EUSART transmits and receives the LSb first. The EUSART’s transmitter and receiver are functionally independent but use the same data format and baud rate. The Baud Rate Generator produces a clock, either x16 or x64 of the bit shift rate depending on the BRGH and BRG16 bits (TXSTA<2> and BAUDCON<3>). Parity is not supported by the hardware but can be implemented in software and stored as the ninth data bit. While TXIF indicates the status of the TXREG register, another bit, TRMT (TXSTA<1>), shows the status of the TSR register. TRMT is a read-only bit which is set when the TSR register is empty. No interrupt logic is tied to this bit so the user has to poll this bit in order to determine if the TSR register is empty. Note 1: The TSR register is not mapped in data memory so it is not available to the user. When operating in Asynchronous mode, the EUSART module consists of the following important elements: • • • • • • • 2: Flag bit, TXIF, is set when enable bit, TXEN, is set. Baud Rate Generator Sampling Circuit Asynchronous Transmitter Asynchronous Receiver Auto-Wake-up on Sync Break Character 12-Bit Break Character Transmit Auto-Baud Rate Detection 15.2.1 To set up an Asynchronous Transmission: 1. 2. EUSART ASYNCHRONOUS TRANSMITTER 3. 4. The EUSART transmitter block diagram is shown in Figure 15-3. The heart of the transmitter is the Transmit (Serial) Shift Register (TSR). The Shift register obtains its data from the Read/Write Transmit Buffer register, TXREG. The TXREG register is loaded with data in software. The TSR register is not loaded until the Stop bit has been transmitted from the previous load. As soon as the Stop bit is transmitted, the TSR is loaded with new data from the TXREG register (if available). FIGURE 15-3: 5. 6. 7. 8. Initialize the SPBRGH:SPBRG registers for the appropriate baud rate. Set or clear the BRGH and BRG16 bits, as required, to achieve the desired baud rate. Enable the asynchronous serial port by clearing bit, SYNC, and setting bit, SPEN. If interrupts are desired, set enable bit, TXIE. If 9-bit transmission is desired, set transmit bit, TX9. Can be used as address/data bit. Enable the transmission by setting bit, TXEN, which will also set bit, TXIF. If 9-bit transmission is selected, the ninth bit should be loaded in bit, TX9D. Load data to the TXREG register (starts transmission). If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. EUSART TRANSMIT BLOCK DIAGRAM Data Bus TXIF TXREG Register TXIE 8 MSb (8) LSb • • • Pin Buffer and Control 0 TSR Register TX pin Interrupt TXEN Baud Rate CLK TRMT BRG16 SPBRGH SPBRG Baud Rate Generator © 2008 Microchip Technology Inc. SPEN TX9 TX9D DS39760D-page 163 PIC18F2450/4450 FIGURE 15-4: ASYNCHRONOUS TRANSMISSION Write to TXREG Word 1 BRG Output (Shift Clock) TX (pin) Start bit bit 0 bit 1 bit 7/8 Stop bit Word 1 TXIF bit (Transmit Buffer Reg. Empty Flag) 1 TCY Word 1 Transmit Shift Reg TRMT bit (Transmit Shift Reg. Empty Flag) FIGURE 15-5: ASYNCHRONOUS TRANSMISSION (BACK-TO-BACK) Write to TXREG Word 2 Word 1 BRG Output (Shift Clock) TX (pin) TXIF bit (Interrupt Reg. Flag) Start bit INTCON bit 7/8 Stop bit Start bit bit 0 Word 2 Word 1 1 TCY Word 1 Transmit Shift Reg. Word 2 Transmit Shift Reg. This timing diagram shows two consecutive transmissions. TABLE 15-5: Name bit 1 1 TCY TRMT bit (Transmit Shift Reg. Empty Flag) Note: bit 0 REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION Bit 7 Bit 6 GIE/GIEH PEIE/GIEL Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 51 IPR1 RCSTA TXREG TXSTA EUSART Transmit Register CSRC BAUDCON ABDOVF 51 TX9 TXEN SYNC SENDB BRGH TRMT TX9D 51 RCIDL — SCKP BRG16 — WUE ABDEN 51 SPBRGH EUSART Baud Rate Generator Register High Byte 50 SPBRG EUSART Baud Rate Generator Register Low Byte 50 Legend: — = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous transmission. DS39760D-page 164 © 2008 Microchip Technology Inc. PIC18F2450/4450 15.2.2 EUSART ASYNCHRONOUS RECEIVER 15.2.3 The receiver block diagram is shown in Figure 15-6. The data is received on the RX pin and drives the data recovery block. The data recovery block is actually a high-speed shifter operating at x16 times the baud rate, whereas the main receive serial shifter operates at the bit rate or at FOSC. This mode would typically be used in RS-232 systems. This mode would typically be used in RS-485 systems. To set up an Asynchronous Reception with Address Detect Enable: 1. Initialize the SPBRGH:SPBRG registers for the appropriate baud rate. Set or clear the BRGH and BRG16 bits, as required, to achieve the desired baud rate. 2. Enable the asynchronous serial port by clearing the SYNC bit and setting the SPEN bit. 3. If interrupts are required, set the RCEN bit and select the desired priority level with the RCIP bit. 4. Set the RX9 bit to enable 9-bit reception. 5. Set the ADDEN bit to enable address detect. 6. Enable reception by setting the CREN bit. 7. The RCIF bit will be set when reception is complete. The interrupt will be Acknowledged if the RCIE and GIE bits are set. 8. Read the RCSTA register to determine if any error occurred during reception, as well as read bit 9 of data (if applicable). 9. Read RCREG to determine if the device is being addressed. 10. If any error occurred, clear the CREN bit. 11. If the device has been addressed, clear the ADDEN bit to allow all received data into the receive buffer and interrupt the CPU. To set up an Asynchronous Reception: 1. Initialize the SPBRGH:SPBRG registers for the appropriate baud rate. Set or clear the BRGH and BRG16 bits, as required, to achieve the desired baud rate. 2. Enable the asynchronous serial port by clearing bit, SYNC, and setting bit, SPEN. 3. If interrupts are desired, set enable bit, RCIE. 4. If 9-bit reception is desired, set bit, RX9. 5. Enable the reception by setting bit, CREN. 6. Flag bit, RCIF, will be set when reception is complete and an interrupt will be generated if enable bit, RCIE, was set. 7. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. 8. Read the 8-bit received data by reading the RCREG register. 9. If any error occurred, clear the error by clearing enable bit, CREN. 10. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. FIGURE 15-6: SETTING UP 9-BIT MODE WITH ADDRESS DETECT EUSART RECEIVE BLOCK DIAGRAM CREN OERR FERR x64 Baud Rate CLK BRG16 SPBRGH SPBRG Baud Rate Generator ÷ 64 or ÷ 16 or ÷4 RSR Register MSb Stop (8) 7 • • • 1 LSb 0 Start RX9 Pin Buffer and Control Data Recovery RX RX9D RCREG Register FIFO SPEN 8 Interrupt RCIF Data Bus RCIE © 2008 Microchip Technology Inc. DS39760D-page 165 PIC18F2450/4450 FIGURE 15-7: ASYNCHRONOUS RECEPTION Start bit RX (pin) bit 0 bit 1 bit 7/8 Stop bit Rcv Shift Reg Rcv Buffer Reg Start bit bit 0 Stop bit Start bit bit 7/8 Stop bit Word 2 RCREG Word 1 RCREG Read Rcv Buffer Reg RCREG bit 7/8 RCIF (Interrupt Flag) OERR bit CREN Note: This timing diagram shows three words appearing on the RX input. The RCREG (Receive Buffer) is read after the third word causing the OERR (Overrun Error) bit to be set. TABLE 15-6: Name INTCON REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION Bit 7 Bit 6 Bit 5 GIE/GIEH PEIE/GIEL TMR0IE Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: INT0IE RBIE TMR0IF INT0IF RBIF 49 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 51 IPR1 RCSTA RCREG TXSTA EUSART Receive Register 50 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 51 RCIDL — SCKP BRG16 — WUE ABDEN 51 BAUDCON ABDOVF SPBRGH EUSART Baud Rate Generator Register High Byte 50 SPBRG EUSART Baud Rate Generator Register Low Byte 50 Legend: — = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous reception. DS39760D-page 166 © 2008 Microchip Technology Inc. PIC18F2450/4450 15.2.4 AUTO-WAKE-UP ON SYNC BREAK CHARACTER During Sleep mode, all clocks to the EUSART are suspended. Therefore, the Baud Rate Generator is inactive and proper byte reception cannot be performed. The auto-wake-up feature allows the controller to wake-up due to activity on the RX/DT line while the EUSART is operating in Asynchronous mode. The auto-wake-up feature is enabled by setting the WUE bit (BAUDCON<1>). Once set, the typical receive sequence on RX/DT is disabled and the EUSART remains in an Idle state, monitoring for a wake-up event independent of the CPU mode. A wake-up event consists of a high-to-low transition on the RX/DT line. (This coincides with the start of a Sync Break or a Wake-up Signal character for the LIN protocol.) Following a wake-up event, the module generates an RCIF interrupt. The interrupt is generated synchronously to the Q clocks in normal operating modes (Figure 15-8) and asynchronously if the device is in Sleep mode (Figure 15-9). The interrupt condition is cleared by reading the RCREG register. The WUE bit is automatically cleared once a low-to-high transition is observed on the RX line following the wakeup event. At this point, the EUSART module is in Idle mode and returns to normal operation. This signals to the user that the Sync Break event is over. 15.2.4.1 Special Considerations Using Auto-Wake-up Since auto-wake-up functions by sensing rising edge transitions on RX/DT, information with any state changes before the Stop bit may signal a false End-of-Character FIGURE 15-8: (EOC) and cause data or framing errors. To work properly, therefore, the initial character in the transmission must be all ‘0’s. This can be 00h (8 bits) for standard RS-232 devices or 000h (12 bits) for LIN bus. Oscillator start-up time must also be considered, especially in applications using oscillators with longer start-up intervals (i.e., XT or HS mode). The Sync Break (or Wake-up Signal) character must be of sufficient length and be followed by a sufficient interval to allow enough time for the selected oscillator to start and provide proper initialization of the EUSART. 15.2.4.2 Special Considerations Using the WUE Bit The timing of WUE and RCIF events may cause some confusion when it comes to determining the validity of received data. As noted, setting the WUE bit places the EUSART in an Idle mode. The wake-up event causes a receive interrupt by setting the RCIF bit. The WUE bit is cleared after this when a rising edge is seen on RX/ DT. The interrupt condition is then cleared by reading the RCREG register. Ordinarily, the data in RCREG will be dummy data and should be discarded. The fact that the WUE bit has been cleared (or is still set) and the RCIF flag is set should not be used as an indicator of the integrity of the data in RCREG. Users should consider implementing a parallel method in firmware to verify received data integrity. To assure that no actual data is lost, check the RCIDL bit to verify that a receive operation is not in process. If a receive operation is not occurring, the WUE bit may then be set just prior to entering the Sleep mode. AUTO-WAKE-UP BIT (WUE) TIMINGS DURING NORMAL OPERATION Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 WUE bit(1) Bit set by user Auto-Cleared RX/DT Line RCIF Cleared due to user read of RCREG Note 1: The EUSART remains in Idle while the WUE bit is set. FIGURE 15-9: AUTO-WAKE-UP BIT (WUE) TIMINGS DURING SLEEP Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 WUE bit(2) Q1 Bit set by user Auto-Cleared RX/DT Line Note 1 RCIF Sleep Command Executed Note 1: 2: Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Sleep Ends Cleared due to user read of RCREG If the wake-up event requires long oscillator warm-up time, the auto-clear of the WUE bit can occur while the stposc signal is still active. This sequence should not depend on the presence of Q clocks. The EUSART remains in Idle while the WUE bit is set. © 2008 Microchip Technology Inc. DS39760D-page 167 PIC18F2450/4450 15.2.5 BREAK CHARACTER SEQUENCE The EUSART module has the capability of sending the special Break character sequences that are required by the LIN bus standard. The Break character transmit consists of a Start bit, followed by twelve ‘0’ bits and a Stop bit. The Frame Break character is sent whenever the SENDB and TXEN bits (TXSTA<3> and TXSTA<5>) are set while the Transmit Shift Register is loaded with data. Note that the value of data written to TXREG will be ignored and all ‘0’s will be transmitted. The SENDB bit is automatically reset by hardware after the corresponding Stop bit is sent. This allows the user to preload the transmit FIFO with the next transmit byte following the Break character (typically, the Sync character in the LIN specification). Note that the data value written to the TXREG for the Break character is ignored. The write simply serves the purpose of initiating the proper sequence. The TRMT bit indicates when the transmit operation is active or Idle, just as it does during normal transmission. See Figure 15-10 for the timing of the Break character sequence. 15.2.5.1 Break and Sync Transmit Sequence The following sequence will send a message frame header made up of a Break, followed by an Auto-Baud Sync byte. This sequence is typical of a LIN bus master. 1. 2. Configure the EUSART for the desired mode. Set the TXEN and SENDB bits to set up the Break character. FIGURE 15-10: Write to TXREG 3. 4. 5. Load the TXREG with a dummy character to initiate transmission (the value is ignored). Write ‘55h’ to TXREG to load the Sync character into the transmit FIFO buffer. After the Break has been sent, the SENDB bit is reset by hardware. The Sync character now transmits in the preconfigured mode. When the TXREG becomes empty, as indicated by the TXIF, the next data byte can be written to TXREG. 15.2.6 RECEIVING A BREAK CHARACTER The Enhanced USART module can receive a Break character in two ways. The first method forces configuration of the baud rate at a frequency of 9/13 the typical speed. This allows for the Stop bit transition to be at the correct sampling location (13 bits for Break versus Start bit and eight data bits for typical data). The second method uses the auto-wake-up feature described in Section 15.2.4 “Auto-Wake-up on Sync Break Character”. By enabling this feature, the EUSART will sample the next two transitions on RX/DT, cause an RCIF interrupt and receive the next data byte followed by another interrupt. Note that following a Break character, the user will typically want to enable the Auto-Baud Rate Detect feature. For both methods, the user can set the ABD bit once the TXIF interrupt is observed. SEND BREAK CHARACTER SEQUENCE Dummy Write BRG Output (Shift Clock) TX (pin) Start bit bit 0 bit 1 bit 11 Stop bit Break TXIF bit (Transmit Buffer Reg. Empty Flag) TRMT bit (Transmit Shift Reg. Empty Flag) SENDB sampled here Auto-Cleared SENDB (Transmit Shift Reg. Empty Flag) DS39760D-page 168 © 2008 Microchip Technology Inc. PIC18F2450/4450 15.3 EUSART Synchronous Master Mode Once the TXREG register transfers the data to the TSR register (occurs in one TCYCLE), the TXREG register is empty and the TXIF flag bit (PIR1<4>) is set. The interrupt can be enabled or disabled by setting or clearing the interrupt enable bit, TXIE (PIE1<4>). TXIF is set regardless of the state of enable bit, TXIE; it cannot be cleared in software. It will reset only when new data is loaded into the TXREG register. The Synchronous Master mode is entered by setting the CSRC bit (TXSTA<7>). In this mode, the data is transmitted in a half-duplex manner (i.e., transmission and reception do not occur at the same time). When transmitting data, the reception is inhibited and vice versa. Synchronous mode is entered by setting bit, SYNC (TXSTA<4>). In addition, enable bit, SPEN (RCSTA<7>), is set in order to configure the TX and RX pins to CK (clock) and DT (data) lines, respectively. While flag bit, TXIF, indicates the status of the TXREG register, another bit, TRMT (TXSTA<1>), shows the status of the TSR register. TRMT is a read-only bit which is set when the TSR is empty. No interrupt logic is tied to this bit so the user must poll this bit in order to determine if the TSR register is empty. The TSR is not mapped in data memory so it is not available to the user. The Master mode indicates that the processor transmits the master clock on the CK line. Clock polarity is selected with the SCKP bit (BAUDCON<4>). Setting SCKP sets the Idle state on CK as high, while clearing the bit sets the Idle state as low. This option is provided to support Microwire devices with this module. 15.3.1 To set up a Synchronous Master Transmission: 1. EUSART SYNCHRONOUS MASTER TRANSMISSION 2. The EUSART transmitter block diagram is shown in Figure 15-3. The heart of the transmitter is the Transmit (Serial) Shift Register (TSR). The Shift register obtains its data from the Read/Write Transmit Buffer register, TXREG. The TXREG register is loaded with data in software. The TSR register is not loaded until the last bit has been transmitted from the previous load. As soon as the last bit is transmitted, the TSR is loaded with new data from the TXREG (if available). 3. 4. 5. 6. 7. 8. FIGURE 15-11: Initialize the SPBRGH:SPBRG registers for the appropriate baud rate. Set or clear the BRG16 bit, as required, to achieve the desired baud rate. Enable the synchronous master serial port by setting bits, SYNC, SPEN and CSRC. If interrupts are desired, set enable bit, TXIE. If 9-bit transmission is desired, set bit, TX9. Enable the transmission by setting bit, TXEN. If 9-bit transmission is selected, the ninth bit should be loaded in bit, TX9D. Start transmission by loading data to the TXREG register. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. SYNCHRONOUS TRANSMISSION Q1 Q2 Q3Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 RC7/RX/DT pin bit 0 bit 2 bit 7 Word 1 RC6/TX/CK pin (SCKP = 0) RC6/TX/CK pin (SCKP = 1) Write to TXREG Reg bit 1 Write Word 1 bit 0 bit 1 bit 7 Word 2 Write Word 2 TXIF bit (Interrupt Flag) TRMT bit TXEN bit Note: ‘1’ ‘1’ Sync Master mode (SPBRG = 0), continuous transmission of two 8-bit words. © 2008 Microchip Technology Inc. DS39760D-page 169 PIC18F2450/4450 FIGURE 15-12: SYNCHRONOUS TRANSMISSION (THROUGH TXEN) RC7/RX/DT pin bit 0 bit 1 bit 2 bit 6 bit 7 RC6/TX/CK pin Write to TXREG reg TXIF bit TRMT bit TXEN bit TABLE 15-7: Name INTCON REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION Bit 7 Bit 6 Bit 5 GIE/GIEH PEIE/GIEL TMR0IE Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: INT0IE RBIE TMR0IF INT0IF RBIF 49 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 51 RCSTA TXREG EUSART Transmit Register 51 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 51 BAUDCON ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN 51 SPBRGH EUSART Baud Rate Generator Register High Byte 50 SPBRG EUSART Baud Rate Generator Register Low Byte 50 TXSTA Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master transmission. DS39760D-page 170 © 2008 Microchip Technology Inc. PIC18F2450/4450 15.3.2 EUSART SYNCHRONOUS MASTER RECEPTION 3. 4. 5. 6. Ensure bits, CREN and SREN, are clear. If interrupts are desired, set enable bit, RCIE. If 9-bit reception is desired, set bit, RX9. If a single reception is required, set bit, SREN. For continuous reception, set bit, CREN. 7. Interrupt flag bit, RCIF, will be set when reception is complete and an interrupt will be generated if the enable bit, RCIE, was set. 8. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. 9. Read the 8-bit received data by reading the RCREG register. 10. If any error occurred, clear the error by clearing bit, CREN. 11. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. Once Synchronous mode is selected, reception is enabled by setting either the Single Receive Enable bit, SREN (RCSTA<5>), or the Continuous Receive Enable bit, CREN (RCSTA<4>). Data is sampled on the RX pin on the falling edge of the clock. If enable bit, SREN, is set, only a single word is received. If enable bit, CREN, is set, the reception is continuous until CREN is cleared. If both bits are set, then CREN takes precedence. To set up a Synchronous Master Reception: 1. 2. Initialize the SPBRGH:SPBRG registers for the appropriate baud rate. Set or clear the BRG16 bit, as required, to achieve the desired baud rate. Enable the synchronous master serial port by setting bits, SYNC, SPEN and CSRC. FIGURE 15-13: SYNCHRONOUS RECEPTION (MASTER MODE, SREN) Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 RC7/RX/DT pin bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 RC6/TX/CK pin (SCKP = 0) RC6/TX/CK pin (SCKP = 1) Write to SREN bit SREN bit CREN bit ‘0’ ‘0’ RCIF bit (Interrupt) Read RXREG Note: Timing diagram demonstrates Sync Master mode with SREN bit = 1 and BRGH bit = 0. TABLE 15-8: Name INTCON REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 51 RCSTA RCREG TXSTA EUSART Receive Register CSRC BAUDCON ABDOVF 50 TX9 TXEN SYNC SENDB BRGH TRMT TX9D 51 RCIDL — SCKP BRG16 — WUE ABDEN 51 SPBRGH EUSART Baud Rate Generator Register High Byte 51 SPBRG EUSART Baud Rate Generator Register Low Byte 50 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception. © 2008 Microchip Technology Inc. DS39760D-page 171 PIC18F2450/4450 15.4 EUSART Synchronous Slave Mode To set up a Synchronous Slave Transmission: 1. Synchronous Slave mode is entered by clearing bit, CSRC (TXSTA<7>). This mode differs from the Synchronous Master mode in that the shift clock is supplied externally at the CK pin (instead of being supplied internally in Master mode). This allows the device to transfer or receive data while in any low-power mode. 15.4.1 2. 3. 4. 5. 6. EUSART SYNCHRONOUS SLAVE TRANSMIT The operation of the Synchronous Master and Slave modes is identical, except in the case of Sleep mode. 7. 8. If two words are written to the TXREG register and then the SLEEP instruction is executed, the following will occur: a) b) c) d) e) Enable the synchronous slave serial port by setting bits, SYNC and SPEN, and clearing bit, CSRC. Clear bits, CREN and SREN. If interrupts are desired, set enable bit, TXIE. If 9-bit transmission is desired, set bit, TX9. Enable the transmission by setting enable bit, TXEN. If 9-bit transmission is selected, the ninth bit should be loaded in bit, TX9D. Start transmission by loading data to the TXREG register. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. The first word will immediately transfer to the TSR register and transmit. The second word will remain in the TXREG register. Flag bit, TXIF, will not be set. When the first word has been shifted out of TSR, the TXREG register will transfer the second word to the TSR and flag bit, TXIF, will now be set. If enable bit, TXIE, is set, the interrupt will wake the chip from Sleep. If the global interrupt is enabled, the program will branch to the interrupt vector. TABLE 15-9: Name INTCON REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION Bit 7 Bit 6 GIE/GIEH PEIE/GIEL Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 51 RCSTA TXREG EUSART Transmit Register 51 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D BAUDCON ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN SPBRGH EUSART Baud Rate Generator Register High Byte 50 SPBRG EUSART Baud Rate Generator Register Low Byte 50 TXSTA 51 51 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave transmission. DS39760D-page 172 © 2008 Microchip Technology Inc. PIC18F2450/4450 15.4.2 EUSART SYNCHRONOUS SLAVE RECEPTION To set up a Synchronous Slave Reception: 1. The operation of the Synchronous Master and Slave modes is identical, except in the case of Sleep or any Idle mode and bit, SREN, which is a “don’t care” in Slave mode. If receive is enabled by setting the CREN bit prior to entering Sleep or any Idle mode, then a word may be received while in this low-power mode. Once the word is received, the RSR register will transfer the data to the RCREG register. If the RCIE enable bit is set, the interrupt generated will wake the chip from the lowpower mode. If the global interrupt is enabled, the program will branch to the interrupt vector. Enable the synchronous master serial port by setting bits, SYNC and SPEN, and clearing bit, CSRC. If interrupts are desired, set enable bit, RCIE. If 9-bit reception is desired, set bit, RX9. To enable reception, set enable bit, CREN. Flag bit RCIF will be set when reception is complete. An interrupt will be generated if enable bit, RCIE, was set. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. Read the 8-bit received data by reading the RCREG register. If any error occurred, clear the error by clearing bit, CREN. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. 2. 3. 4. 5. 6. 7. 8. 9. TABLE 15-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION Name INTCON Bit 7 Bit 6 Bit 5 GIE/GIEH PEIE/GIEL TMR0IE Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: INT0IE RBIE TMR0IF INT0IF RBIF 49 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 51 RCSTA RCREG TXSTA EUSART Receive Register 50 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 51 BAUDCON ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN 51 SPBRGH EUSART Baud Rate Generator Register High Byte 50 SPBRG EUSART Baud Rate Generator Register Low Byte 50 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception. © 2008 Microchip Technology Inc. DS39760D-page 173 PIC18F2450/4450 NOTES: DS39760D-page 174 © 2008 Microchip Technology Inc. PIC18F2450/4450 16.0 10-BIT ANALOG-TO-DIGITAL CONVERTER (A/D) MODULE The Analog-to-Digital (A/D) Converter module has 10 inputs for the 28-pin devices and 13 for the 40/44-pin devices. This module allows conversion of an analog input signal to a corresponding 10-bit digital number. The ADCON0 register, shown in Register 16-1, controls the operation of the A/D module. The ADCON1 register, shown in Register 16-2, configures the functions of the port pins. The ADCON2 register, shown in Register 16-3, configures the A/D clock source, programmed acquisition time and justification. The module has five registers: • • • • • A/D Result High Register (ADRESH) A/D Result Low Register (ADRESL) A/D Control Register 0 (ADCON0) A/D Control Register 1 (ADCON1) A/D Control Register 2 (ADCON2) REGISTER 16-1: ADCON0: A/D CONTROL REGISTER 0 U0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — CHS3 CHS2 CHS1 CHS0 GO/DONE ADON bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-6 Unimplemented: Read as ‘0’ bit 5-2 CHS3:CHS0: Analog Channel Select bits 0000 = Channel 0 (AN0) 0001 = Channel 1 (AN1) 0010 = Channel 2 (AN2) 0011 = Channel 3 (AN3) 0100 = Channel 4 (AN4) 0101 = Channel 5 (AN5)(1,2) 0110 = Channel 6 (AN6)(1,2) 0111 = Channel 7 (AN7)(1,2) 1000 = Channel 8 (AN8) 1001 = Channel 9 (AN9) 1010 = Channel 10 (AN10) 1011 = Channel 11 (AN11) 1100 = Channel 12 (AN12 1101 = Unimplemented(2) 1110 = Unimplemented(2) 1111 = Unimplemented(2) bit 1 GO/DONE: A/D Conversion Status bit When ADON = 1: 1 = A/D conversion in progress 0 = A/D Idle bit 0 ADON: A/D On bit 1 = A/D Converter module is enabled 0 = A/D Converter module is disabled Note 1: 2: x = Bit is unknown These channels are not implemented on 28-pin devices. Performing a conversion on unimplemented channels will return a floating input measurement. © 2008 Microchip Technology Inc. DS39760D-page 175 PIC18F2450/4450 REGISTER 16-2: ADCON1: A/D CONTROL REGISTER 1 U-0 U-0 R/W-0 R/W-0 R/W-0(1) R/W(1) R/W(1) R/W(1) — — VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared PCFG3: PCFG0 AN5(2) AN4 AN3 AN2 AN1 AN0 PCFG3:PCFG0: A/D Port Configuration Control bits: AN6(2) bit 3-0 AN7(2) VCFG0: Voltage Reference Configuration bit (VREF+ source) 1 = VREF+ (AN3) 0 = VDD AN8 bit 4 AN9 VCFG1: Voltage Reference Configuration bit (VREF- source) 1 = VREF- (AN2) 0 = VSS AN10 bit 5 AN11 Unimplemented: Read as ‘0’ AN12 bit 7-6 0000(1) 0001 0010 0011 0100 0101 0110 A A A A A A A A A A A A A A A D D D D D A A A D D D D A A A A D D D A A A A A D D A A A A A A D A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D A D D D D D D D A A D D D D D D A A A D D D D D A A A A D D D D A A A A A D D D A A A A A A D D A A A A A A A D 0111(1) 1000 1001 1010 1011 1100 1101 1110 1111 A = Analog input Note 1: 2: x = Bit is unknown D = Digital I/O The POR value of the PCFG bits depends on the value of the PBADEN Configuration bit. When PBADEN = 1, PCFG<3:0> = 0000; when PBADEN = 0, PCFG<3:0> = 0111. AN5 through AN7 are available only on 40/44-pin devices. DS39760D-page 176 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 16-3: ADCON2: A/D CONTROL REGISTER 2 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADFM — ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 ADFM: A/D Result Format Select bit 1 = Right justified 0 = Left justified bit 6 Unimplemented: Read as ‘0’ bit 5-3 ACQT2:ACQT0: A/D Acquisition Time Select bits 111 = 20 TAD 110 = 16 TAD 101 = 12 TAD 100 = 8 TAD 011 = 6 TAD 010 = 4 TAD 001 = 2 TAD 000 = 0 TAD(1) bit 2-0 ADCS2:ADCS0: A/D Conversion Clock Select bits 111 = FRC (clock derived from A/D RC oscillator)(1) 110 = FOSC/64 101 = FOSC/16 100 = FOSC/4 011 = FRC (clock derived from A/D RC oscillator)(1) 010 = FOSC/32 001 = FOSC/8 000 = FOSC/2 Note 1: x = Bit is unknown If the A/D FRC clock source is selected, a delay of one TCY (instruction cycle) is added before the A/D clock starts. This allows the SLEEP instruction to be executed before starting a conversion. © 2008 Microchip Technology Inc. DS39760D-page 177 PIC18F2450/4450 The analog reference voltage is software selectable to either the device’s positive and negative supply voltage (VDD and VSS) or the voltage level on the RA3/AN3/ VREF+ and RA2/AN2/VREF- pins. A device Reset forces all registers to their Reset state. This forces the A/D module to be turned off and any conversion in progress is aborted. Each port pin associated with the A/D Converter can be configured as an analog input or as a digital I/O. The ADRESH and ADRESL registers contain the result of the A/D conversion. When the A/D conversion is complete, the result is loaded into the ADRESH:ADRESL register pair, the GO/DONE bit (ADCON0 register) is cleared and A/D Interrupt Flag bit, ADIF, is set. The block diagram of the A/D module is shown in Figure 16-1. The A/D Converter has a unique feature of being able to operate while the device is in Sleep mode. To operate in Sleep, the A/D conversion clock must be derived from the A/D’s internal RC oscillator. The output of the sample and hold is the input into the converter, which generates the result via successive approximation. FIGURE 16-1: A/D BLOCK DIAGRAM CHS3:CHS0 1100 1011 1010 1001 1000 0111 0110 0101 0100 VAIN 0011 (Input Voltage) 10-Bit A/D Converter 0010 0001 VCFG1:VCFG0 VDD(2) Reference Voltage VREF+ VREF- 0000 AN12 AN11 AN10 AN9 AN8 AN7(1) AN6(1) AN5(1) AN4 AN3 AN2 AN1 AN0 X0 X1 1X 0X VSS(2) Note 1: 2: Channels AN5 through AN7 are not available on 28-pin devices. I/O pins have diode protection to VDD and VSS. DS39760D-page 178 © 2008 Microchip Technology Inc. PIC18F2450/4450 Wait for A/D conversion to complete, by either: • Polling for the GO/DONE bit to be cleared OR • Waiting for the A/D interrupt Read A/D Result registers (ADRESH:ADRESL); clear bit, ADIF, if required. For next conversion, go to step 1 or step 2, as required. The A/D conversion time per bit is defined as TAD. A minimum wait of 3 TAD is required before the next acquisition starts. 6. 7. FIGURE 16-2: 3FFh 1. 3FEh FIGURE 16-3: 002h 001h 1023 LSB 1023.5 LSB 1022 LSB 1022.5 LSB 3 LSB Analog Input Voltage ANALOG INPUT MODEL VDD Rs VAIN 2 LSB 000h 2.5 LSB 3. 4. A/D TRANSFER FUNCTION 003h 0.5 LSB 2. Configure the A/D module: • Configure analog pins, voltage reference and digital I/O (ADCON1) • Select A/D input channel (ADCON0) • Select A/D acquisition time (ADCON2) • Select A/D conversion clock (ADCON2) • Turn on A/D module (ADCON0) Configure A/D interrupt (if desired): • Clear ADIF bit • Set ADIE bit • Set GIE bit Wait the required acquisition time (if required). Start conversion: • Set GO/DONE bit (ADCON0 register) Digital Code Output The following steps should be followed to perform an A/D conversion: 1 LSB After the A/D module has been configured as desired, the selected channel must be acquired before the conversion is started. The analog input channels must have their corresponding TRIS bits selected as an input. To determine acquisition time, see Section 16.1 “A/D Acquisition Requirements”. After this acquisition time has elapsed, the A/D conversion can be started. An acquisition time can be programmed to occur between setting the GO/DONE bit and the actual start of the conversion. 5. 1.5 LSB The value in the ADRESH:ADRESL registers is not modified for a Power-on Reset. The ADRESH:ADRESL registers will contain unknown data after a Power-on Reset. ANx CPIN 5 pF Sampling Switch VT = 0.6V RIC ≤ 1k VT = 0.6V SS RSS ILEAKAGE ±100 nA CHOLD = 25 pF VSS Legend: CPIN = Input Capacitance VT = Threshold Voltage ILEAKAGE = Leakage Current at the pin due to various junctions = Interconnect Resistance RIC = Sampling Switch SS = Sample/hold Capacitance (from DAC) CHOLD RSS = Sampling Switch Resistance © 2008 Microchip Technology Inc. VDD 6V 5V 4V 3V 2V 1 2 3 4 Sampling Switch (kΩ) DS39760D-page 179 PIC18F2450/4450 16.1 A/D Acquisition Requirements For the A/D Converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The analog input model is shown in Figure 16-3. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD). The source impedance affects the offset voltage at the analog input (due to pin leakage current). The maximum recommended impedance for analog sources is 2.5 kΩ. After the analog input channel is selected (changed), the channel must be sampled for at least the minimum acquisition time before starting a conversion. Note: CHOLD Rs Conversion Error VDD Temperature = = ≤ = = 25 pF 2.5 kΩ 1/2 LSb 5V → RSS = 2 kΩ 85°C (system max.) ACQUISITION TIME = Amplifier Settling Time + Holding Capacitor Charging Time + Temperature Coefficient = TAMP + TC + TCOFF EQUATION 16-2: VHOLD or TC Example 16-3 shows the calculation of the minimum required acquisition time TACQ. This calculation is based on the following application system assumptions: When the conversion is started, the holding capacitor is disconnected from the input pin. EQUATION 16-1: TACQ To calculate the minimum acquisition time, Equation 16-1 may be used. This equation assumes that 1/2 LSb error is used (1024 steps for the A/D). The 1/2 LSb error is the maximum error allowed for the A/D to meet its specified resolution. A/D MINIMUM CHARGING TIME = (VREF – (VREF/2048)) • (1 – e(-TC/CHOLD(RIC + RSS + RS))) = -(CHOLD)(RIC + RSS + RS) ln(1/2048) EQUATION 16-3: CALCULATING THE MINIMUM REQUIRED ACQUISITION TIME TACQ = TAMP + TC + TCOFF TAMP = 0.2 μs TCOFF = (Temp – 25°C)(0.02 μs/°C) (85°C – 25°C)(0.02 μs/°C) 1.2 μs Temperature coefficient is only required for temperatures > 25°C. Below 25°C, TCOFF = 0 ms. TC = -(CHOLD)(RIC + RSS + RS) ln(1/2047) μs -(25 pF) (1 kΩ + 2 kΩ + 2.5 kΩ) ln(0.0004883) μs 1.05 μs TACQ = 0.2 μs + 1 μs + 1.2 μs 2.4 μs DS39760D-page 180 © 2008 Microchip Technology Inc. PIC18F2450/4450 16.2 Selecting and Configuring Acquisition Time 16.3 Selecting the A/D Conversion Clock The ADCON2 register allows the user to select an acquisition time that occurs each time the GO/DONE bit is set. It also gives users the option to use an automatically determined acquisition time. The A/D conversion time per bit is defined as TAD. The A/D conversion requires 11 TAD per 10-bit conversion. The source of the A/D conversion clock is software selectable. There are seven possible options for TAD: Acquisition time may be set with the ACQT2:ACQT0 bits (ADCON2<5:3>) which provide a range of 2 to 20 TAD. When the GO/DONE bit is set, the A/D module continues to sample the input for the selected acquisition time, then automatically begins a conversion. Since the acquisition time is programmed, there may be no need to wait for an acquisition time between selecting a channel and setting the GO/DONE bit. • • • • • • • Manual acquisition is selected when ACQT2:ACQT0 = 000. When the GO/DONE bit is set, sampling is stopped and a conversion begins. The user is responsible for ensuring the required acquisition time has passed between selecting the desired input channel and setting the GO/DONE bit. This option is also the default Reset state of the ACQT2:ACQT0 bits and is compatible with devices that do not offer programmable acquisition times. For correct A/D conversions, the A/D conversion clock (TAD) must be as short as possible but greater than the minimum TAD (see parameter 130 in Table 21-18 for more information). 2 TOSC 4 TOSC 8 TOSC 16 TOSC 32 TOSC 64 TOSC Internal RC Oscillator Table 16-1 shows the resultant TAD times derived from the device operating frequencies and the A/D clock source selected. In either case, when the conversion is completed, the GO/DONE bit is cleared, the ADIF flag is set and the A/D begins sampling the currently selected channel again. If an acquisition time is programmed, there is nothing to indicate if the acquisition time has ended or if the conversion has begun. TABLE 16-1: TAD vs. DEVICE OPERATING FREQUENCIES AD Clock Source (TAD) Operation ADCS2:ADCS0 PIC18FX450 PIC18LFX450(4) 2 TOSC 000 2.86 MHz 1.43 MHz 4 TOSC 100 5.71 MHz 2.86 MHz 8 TOSC 001 11.43 MHz 5.72 MHz 16 TOSC 101 22.86 MHz 11.43 MHz 32 TOSC 010 45.71 MHz 22.86 MHz 64 TOSC 110 48.0 MHz 45.71 MHz RC(3) Note 1: 2: 3: 4: Maximum Device Frequency x11 1.00 MHz(1) 1.00 MHz(2) The RC source has a typical TAD time of 1.2 μs. The RC source has a typical TAD time of 2.5 μs. For device frequencies above 1 MHz, the device must be in Sleep for the entire conversion or the A/D accuracy may be out of specification. Low-power devices only. © 2008 Microchip Technology Inc. DS39760D-page 181 PIC18F2450/4450 16.4 Operation in Power-Managed Modes The selection of the automatic acquisition time and A/D conversion clock is determined in part by the clock source and frequency while in a power-managed mode. If the A/D is expected to operate while the device is in a power-managed mode, the ACQT2:ACQT0 and ADCS2:ADCS0 bits in ADCON2 should be updated in accordance with the clock source to be used in that mode. After entering the mode, an A/D acquisition or conversion may be started. Once started, the device should continue to be clocked by the same clock source until the conversion has been completed. If desired, the device may be placed into the corresponding Idle mode during the conversion. If the device clock frequency is less than 1 MHz, the A/D RC clock source should be selected. Operation in the Sleep mode requires the A/D FRC clock to be selected. If bits ACQT2:ACQT0 are set to ‘000’ and a conversion is started, the conversion will be delayed one instruction cycle to allow execution of the SLEEP instruction and entry to Sleep mode. The IDLEN bit (OSCCON<7>) must have already been cleared prior to starting the conversion. DS39760D-page 182 16.5 Configuring Analog Port Pins The ADCON1, TRISA, TRISB and TRISE registers all configure the A/D port pins. The port pins needed as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. The A/D operation is independent of the state of the CHS3:CHS0 bits and the TRIS bits. Note 1: When reading the PORT register, all pins configured as analog input channels will read as cleared (a low level). Pins configured as digital inputs will convert as analog inputs. Analog levels on a digitally configured input will be accurately converted. 2: Analog levels on any pin defined as a digital input may cause the digital input buffer to consume current out of the device’s specification limits. 3: The PBADEN bit in Configuration Register 3H configures PORTB pins to reset as analog or digital pins by controlling how the PCFG0 bits in ADCON1 are reset. © 2008 Microchip Technology Inc. PIC18F2450/4450 16.6 A/D Conversions After the A/D conversion is completed or aborted, a 2 TAD wait is required before the next acquisition can be started. After this wait, acquisition on the selected channel is automatically started. Figure 16-4 shows the operation of the A/D Converter after the GO/DONE bit has been set and the ACQT2:ACQT0 bits are cleared. A conversion is started after the following instruction to allow entry into Sleep mode before the conversion begins. Note: Figure 16-5 shows the operation of the A/D Converter after the GO/DONE bit has been set, the ACQT2:ACQT0 bits are set to ‘010’ and selecting a 4 TAD acquisition time before the conversion starts. 16.7 Discharge The discharge phase is used to initialize the value of the capacitor array. The array is discharged before every sample. This feature helps to optimize the unitygain amplifier as the circuit always needs to charge the capacitor array, rather than charge/discharge based on previous measurement values. Clearing the GO/DONE bit during a conversion will abort the current conversion. The A/D Result register pair will NOT be updated with the partially completed A/D conversion sample. This means the ADRESH:ADRESL registers will continue to contain the value of the last completed conversion (or the last value written to the ADRESH:ADRESL registers). FIGURE 16-4: The GO/DONE bit should NOT be set in the same instruction that turns on the A/D. A/D CONVERSION TAD CYCLES (ACQT<2:0> = 000, TACQ = 0) TCY - TAD TAD1 TAD2 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 TAD9 TAD10 TAD11 TAD1 b4 b1 b0 b6 b7 b2 b9 b8 b3 b5 Conversion starts Discharge Holding capacitor is disconnected from analog input (typically 100 ns) Set GO/DONE bit On the following cycle: ADRESH:ADRESL is loaded, GO/DONE bit is cleared, ADIF bit is set, holding capacitor is connected to analog input. FIGURE 16-5: A/D CONVERSION TAD CYCLES (ACQT<2:0> = 010, TACQ = 4 TAD) TAD Cycles TACQ Cycles 1 2 3 Automatic Acquisition Time 4 1 2 3 4 5 6 7 8 9 10 11 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Conversion starts (Holding capacitor is disconnected) Set GO/DONE bit (Holding capacitor continues acquiring input) © 2008 Microchip Technology Inc. TAD1 Discharge On the following cycle: ADRESH:ADRESL is loaded, GO/DONE bit is cleared, ADIF bit is set, holding capacitor is connected to analog input. DS39760D-page 183 PIC18F2450/4450 16.8 Use of the CCP1 Trigger An A/D conversion can be started by the Special Event Trigger of the CCP1 module. This requires that the CCP1M3:CCP1M0 bits (CCP1CON<3:0>) be programmed as ‘1011’ and that the A/D module is enabled (ADON bit is set). When the trigger occurs, the GO/DONE bit will be set, starting the A/D acquisition and conversion, and the Timer1 counter will be reset to zero. Timer1 is reset to automatically repeat the A/D acquisition period with minimal software overhead TABLE 16-2: Name INTCON (moving ADRESH:ADRESL to the desired location). The appropriate analog input channel must be selected and the minimum acquisition period is either timed by the user, or an appropriate TACQ time selected before the Special Event Trigger sets the GO/DONE bit (starts a conversion). If the A/D module is not enabled (ADON is cleared), the Special Event Trigger will be ignored by the A/D module but will still reset the Timer1 counter. REGISTERS ASSOCIATED WITH A/D OPERATION Bit 7 Bit 6 GIE/GIEH PEIE/GIEL Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF 51 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE 51 IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP 51 PIR2 OSCFIF — USBIF — — HLVDIF — — 51 PIE2 OSCFIE — USBIE — — HLVDIE — — 51 IPR2 OSCFIP — USBIP — — HLVDIP — — 51 ADRESH A/D Result Register High Byte 50 ADRESL A/D Result Register Low Byte 50 ADCON0 — — CHS3 CHS2 CHS1 CHS0 GO/DONE ADON 50 ADCON1 — — VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 50 ADCON2 ADFM — ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0 50 PORTA — RA6(2) RA5 RA4 RA3 RA2 RA1 RA0 51 TRISA — TRISA6(2) TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 51 PORTB RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 51 TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 51 LATB LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 51 (4) (4) (4) 51 PORTE — — — — TRISE(4) — — — — LATE(4) — — — — RE3 (1,3) RE2 RE1 RE0 — TRISE2(4) TRISE1(4) TRISE0(4) 51 — LATE2(4) 51 LATE1(4) LATE0(4) Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for A/D conversion. Note 1: Implemented only when Master Clear functionality is disabled (MCLRE Configuration bit = 0). 2: RA6 and its associated latch and data direction bits are enabled as I/O pins based on oscillator configuration; otherwise, they are read as ‘0’. 3: RE3 port bit is available only as an input pin when the MCLRE Configuration bit is ‘0’. 4: These registers and/or bits are not implemented on 28-pin devices. DS39760D-page 184 © 2008 Microchip Technology Inc. PIC18F2450/4450 17.0 HIGH/LOW-VOLTAGE DETECT (HLVD) PIC18F2450/4450 devices have a High/Low-Voltage Detect module (HLVD). This is a programmable circuit that allows the user to specify both a device voltage trip point and the direction of change from that point. If the device experiences an excursion past the trip point in that direction, an interrupt flag is set. If the interrupt is enabled, the program execution will branch to the interrupt vector address and the software can then respond to the interrupt. REGISTER 17-1: The High/Low-Voltage Detect Control register (Register 17-1) completely controls the operation of the HLVD module. This allows the circuitry to be “turned off” by the user under software control which minimizes the current consumption for the device. The block diagram for the HLVD module is shown in Figure 17-1. HLVDCON: HIGH/LOW-VOLTAGE DETECT CONTROL REGISTER R/W-0 U-0 R-0 R/W-0 R/W-0 R/W-1 R/W-0 R/W-1 VDIRMAG — IRVST HLVDEN HLVDL3(1) HLVDL2(1) HLVDL1(1) HLVDL0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 VDIRMAG: Voltage Direction Magnitude Select bit 1 = Event occurs when voltage equals or exceeds trip point (HLVDL3:HLDVL0) 0 = Event occurs when voltage equals or falls below trip point (HLVDL3:HLVDL0) bit 6 Unimplemented: Read as ‘0’ bit 5 IRVST: Internal Reference Voltage Stable Flag bit 1 = Indicates that the voltage detect logic will generate the interrupt flag at the specified voltage trip point 0 = Indicates that the voltage detect logic will not generate the interrupt flag at the specified voltage trip point and the LVD interrupt should not be enabled bit 4 HLVDEN: High/Low-Voltage Detect Power Enable bit 1 = HLVD enabled 0 = HLVD disabled bit 3-0 HLVDL3:HLVDL0: Voltage Detection Limit bits(1) 1111 = Reserved 1110 = Maximum setting . . . 0000 = Minimum setting Note 1: See Table 21-4 in Section 21.0 “Electrical Characteristics” for specifications. © 2008 Microchip Technology Inc. DS39760D-page 185 PIC18F2450/4450 The module is enabled by setting the HLVDEN bit. Each time that the HLVD module is enabled, the circuitry requires some time to stabilize. The IRVST bit is a read-only bit and is used to indicate when the circuit is stable. The module can only generate an interrupt after the circuit is stable and IRVST is set. event, depending on the configuration of the module. When the supply voltage is equal to the trip point, the voltage tapped off of the resistor array is equal to the internal reference voltage generated by the voltage reference module. The comparator then generates an interrupt signal by setting the HLVDIF bit. The VDIRMAG bit determines the overall operation of the module. When VDIRMAG is cleared, the module monitors for drops in VDD below a predetermined set point. When the bit is set, the module monitors for rises in VDD above the set point. The trip point voltage is software programmable to any one of 16 values. The trip point is selected by programming the HLVDL3:HLVDL0 bits (HLVDCON<3:0>). 17.1 The HLVD module has an additional feature that allows the user to supply the trip voltage to the module from an external source. This mode is enabled when bits, HLVDL3:HLVDL0, are set to ‘1111’. In this state, the comparator input is multiplexed from the external input pin, HLVDIN. This gives users flexibility because it allows them to configure the High/Low-Voltage Detect interrupt to occur at any voltage in the valid operating range. Operation When the HLVD module is enabled, a comparator uses an internally generated reference voltage as the set point. The set point is compared with the trip point, where each node in the resistor divider represents a trip point voltage. The “trip point” voltage is the voltage level at which the device detects a high or low-voltage FIGURE 17-1: HLVD MODULE BLOCK DIAGRAM (WITH EXTERNAL INPUT) Externally Generated Trip Point VDD VDD HLVDL3:HLVDL0 HLVDCON Register HLVDEN 16-to-1 MUX HLVDIN VDIRMAG Set HLVDIF HLVDEN BOREN DS39760D-page 186 Internal Voltage Reference 1.2V Typical © 2008 Microchip Technology Inc. PIC18F2450/4450 17.2 HLVD Setup Depending on the application, the HLVD module does not need to be operating constantly. To decrease the current requirements, the HLVD circuitry may only need to be enabled for short periods where the voltage is checked. After doing the check, the HLVD module may be disabled. The following steps are needed to set up the HLVD module: 1. 2. 3. 4. 5. 6. Disable the module by clearing the HLVDEN bit (HLVDCON<4>). Write the value to the HLVDL3:HLVDL0 bits that selects the desired HLVD trip point. Set the VDIRMAG bit to detect high voltage (VDIRMAG = 1) or low voltage (VDIRMAG = 0). Enable the HLVD module by setting the HLVDEN bit. Clear the HLVD Interrupt Flag, HLVDIF (PIR2<2>), which may have been set from a previous interrupt. Enable the HLVD interrupt, if interrupts are desired, by setting the HLVDIE and GIE/GIEH bits (PIE2<2> and INTCON<7>). An interrupt will not be generated until the IRVST bit is set. 17.3 17.4 The internal reference voltage of the HLVD module, specified in electrical specification parameter D420 (see Table 21-4 in Section 21.0 “Electrical Characteristics”), may be used by other internal circuitry, such as the Programmable Brown-out Reset. If the HLVD or other circuits using the voltage reference are disabled to lower the device’s current consumption, the reference voltage circuit will require time to become stable before a low or high-voltage condition can be reliably detected. This start-up time, TIRVST, is an interval that is independent of device clock speed. It is specified in electrical specification parameter 36 (Table 21-10). Current Consumption The HLVD interrupt flag is not enabled until TIRVST has expired and a stable reference voltage is reached. For this reason, brief excursions beyond the set point may not be detected during this interval. Refer to Figure 17-2 or Figure 17-3. When the module is enabled, the HLVD comparator and voltage divider are enabled and will consume static current. The total current consumption, when enabled, is specified in electrical specification parameter D022 (Section 270 “DC Characteristics”). FIGURE 17-2: HLVD Start-up Time LOW-VOLTAGE DETECT OPERATION (VDIRMAG = 0) CASE 1: HLVDIF may not be set VDD VHLVD HLVDIF Enable HLVD TIRVST IRVST Internal Reference is Stable HLVDIF Cleared in Software CASE 2: VDD VHLVD HLVDIF Enable HLVD TIRVST IRVST Internal Reference is Stable HLVDIF Cleared in Software HLVDIF Cleared in Software, HLVDIF Remains Set since HLVD Condition still Exists © 2008 Microchip Technology Inc. DS39760D-page 187 PIC18F2450/4450 FIGURE 17-3: HIGH-VOLTAGE DETECT OPERATION (VDIRMAG = 1) CASE 1: HLVDIF may not be Set VHLVD VDD HLVDIF Enable HLVD TIRVST IRVST HLVDIF Cleared in Software Internal Reference is Stable CASE 2: VHLVD VDD HLVDIF Enable HLVD TIRVST IRVST Internal Reference is Stable HLVDIF Cleared in software HLVDIF Cleared in Software, HLVDIF Remains Set since HLVD Condition still Exists Applications In many applications, the ability to detect a drop below or rise above a particular threshold is desirable. For example, the HLVD module could be periodically enabled to detect Universal Serial Bus (USB) attach or detach. This assumes the device is powered by a lower voltage source than the USB when detached. An attach would indicate a high-voltage detect from, for example, 3.3V to 5V (the voltage on USB) and vice versa for a detach. This feature could save a design a few extra components and an attach signal (input pin). For general battery applications, Figure 17-4 shows a possible voltage curve. Over time, the device voltage decreases. When the device voltage reaches voltage, VA, the HLVD logic generates an interrupt at time, TA. The interrupt could cause the execution of an ISR, which would allow the application to perform “housekeeping tasks” and perform a controlled shutdown before the device voltage exits the valid operating range at TB. The HLVD, thus, would give the application a time window, represented by the difference between TA and TB, to safely exit. DS39760D-page 188 FIGURE 17-4: TYPICAL HIGH/LOW-VOLTAGE DETECT APPLICATION VA VB Voltage 17.5 Time TA TB Legend: VA = HLVD trip point VB = Minimum valid device operating voltage © 2008 Microchip Technology Inc. PIC18F2450/4450 17.6 Operation During Sleep 17.7 When enabled, the HLVD circuitry continues to operate during Sleep. If the device voltage crosses the trip point, the HLVDIF bit will be set and the device will wake-up from Sleep. Device execution will continue from the interrupt vector address if interrupts have been globally enabled. TABLE 17-1: Effects of a Reset A device Reset forces all registers to their Reset state. This forces the HLVD module to be turned off. REGISTERS ASSOCIATED WITH HIGH/LOW-VOLTAGE DETECT MODULE Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: HLVDCON VDIRMAG — IRVST HLVDEN HLVDL3 HLVDL2 HLVDL1 HLVDL0 50 INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49 PIR2 OSCFIF — USBIF — — HLVDIF — — 51 PIE2 OSCFIE — USBIE — — HLVDIE — — 51 IPR2 OSCFIP — USBIP — — HLVDIP — — 51 Legend: — = unimplemented, read as ‘0’. Shaded cells are unused by the HLVD module. © 2008 Microchip Technology Inc. DS39760D-page 189 PIC18F2450/4450 NOTES: DS39760D-page 190 © 2008 Microchip Technology Inc. PIC18F2450/4450 18.0 SPECIAL FEATURES OF THE CPU PIC18F2450/4450 devices include several features intended to maximize reliability and minimize cost through elimination of external components. These are: • Oscillator Selection • Resets: - Power-on Reset (POR) - Power-up Timer (PWRT) - Oscillator Start-up Timer (OST) - Brown-out Reset (BOR) • Interrupts • Watchdog Timer (WDT) • Fail-Safe Clock Monitor (FSCM) • Two-Speed Start-up • Code Protection • ID Locations • In-Circuit Serial Programming (ICSP) In addition to their Power-up and Oscillator Start-up Timers provided for Resets, PIC18F2450/4450 devices have a Watchdog Timer, which is either permanently enabled via the Configuration bits or software controlled (if configured as disabled). The inclusion of an internal RC oscillator also provides the additional benefits of a Fail-Safe Clock Monitor (FSCM) and Two-Speed Start-up. FSCM provides for background monitoring of the peripheral clock and automatic switchover in the event of its failure. TwoSpeed Start-up enables code to be executed almost immediately on start-up, while the primary clock source completes its start-up delays. All of these features are enabled and configured by setting the appropriate Configuration register bits. The oscillator can be configured for the application depending on frequency, power, accuracy and cost. All of the options are discussed in detail in Section 2.0 “Oscillator Configurations”. A complete discussion of device Resets and interrupts is available in previous sections of this data sheet. © 2008 Microchip Technology Inc. DS39760D-page 191 PIC18F2450/4450 18.1 Configuration Bits Programming the Configuration registers is done in a manner similar to programming the Flash memory. The WR bit in the EECON1 register starts a self-timed write to the Configuration register. In normal operation mode, a TBLWT instruction, with the TBLPTR pointing to the Configuration register, sets up the address and the data for the Configuration register write. Setting the WR bit starts a long write to the Configuration register. The Configuration registers are written a byte at a time. To write or erase a configuration cell, a TBLWT instruction can write a ‘1’ or a ‘0’ into the cell. For additional details on Flash programming, refer to Section 6.5 “Writing to Flash Program Memory”. The Configuration bits can be programmed (read as ‘0’) or left unprogrammed (read as ‘1’) to select various device configurations. These bits are mapped starting at program memory location 300000h. The user will note that address 300000h is beyond the user program memory space. In fact, it belongs to the configuration memory space (300000h-3FFFFFh), which can only be accessed using table reads and table writes. TABLE 18-1: CONFIGURATION BITS AND DEVICE IDs File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 USBDIV CPUDIV1 CPUDIV0 PLLDIV2 Bit 1 Bit 0 Default/ Unprogrammed Value PLLDIV1 PLLDIV0 --00 0111 FOSC1 FOSC0 00-- 0111 300000h CONFIG1L — — 300001h CONFIG1H IESO FCMEN — — FOSC3 FOSC2 300002h CONFIG2L — — VREGEN BORV1 BORV0 BOREN1 300003h CONFIG2H — — — 300005h CONFIG3H MCLRE — — — — — 1--- -01- 300006h CONFIG4L DEBUG XINST ICPRT(2) — BBSIZ LVP — STVREN 100- 01-1 300008h CONFIG5L — — — — — — CP1 CP0 ---- --11 -1-- ---- BOREN0 PWRTEN WDTPS3 WDTPS2 WDTPS1 WDTPS0 LPT1OSC PBADEN WDTEN --01 1111 ---1 1111 300009h CONFIG5H — CPB — — — — — — 30000Ah CONFIG6L — — — — — — WRT1 WRT0 ---- --11 30000Bh CONFIG6H — WRTB WRTC — — — — — -11- ---- 30000Ch CONFIG7L — — — — — — EBTR1 EBTR0 ---- --11 30000Dh CONFIG7H -1-- ---- — EBTRB — — — — — — 3FFFFEh DEVID1 DEV2 DEV1 DEV0 REV4 REV3 REV2 REV1 REV0 xxxx xxxx(1) 3FFFFFh DEVID2 DEV10 DEV9 DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 0001 0010(1) Legend: Note 1: x = unknown, u = unchanged, - = unimplemented. Shaded cells are unimplemented, read as ‘0’. See Register 18-13 and Register 18-14 for device ID values. DEVID registers are read-only and cannot be programmed by the user. Available only on PIC18F4450 devices in 44-pin TQFP packages. Always leave this bit clear in all other devices. 2: DS39760D-page 192 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 18-1: CONFIG1L: CONFIGURATION REGISTER 1 LOW (BYTE ADDRESS 300000h) U-0 U-0 R/P-0 R/P-0 R/P-0 R/P-1 R/P-1 R/P-1 — — USBDIV CPUDIV1 CPUDIV0 PLLDIV2 PLLDIV1 PLLDIV0 bit 7 bit 0 Legend: R = Readable bit P = Programmable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state bit 7-6 Unimplemented: Read as ‘0’ bit 5 USBDIV: USB Clock Selection bit (used in Full-Speed USB mode only; UCFG:FSEN = 1) 1 = USB clock source comes from the 96 MHz PLL divided by 2 0 = USB clock source comes directly from the primary oscillator block with no postscale bit 4-3 CPUDIV1:CPUDIV0: System Clock Postscaler Selection bits For XT, HS, EC and ECIO Oscillator modes: 11 = Primary oscillator divided by 4 to derive system clock 10 = Primary oscillator divided by 3 to derive system clock 01 = Primary oscillator divided by 2 to derive system clock 00 = Primary oscillator used directly for system clock (no postscaler) For XTPLL, HSPLL, ECPLL and ECPIO Oscillator modes: 11 = 96 MHz PLL divided by 6 to derive system clock 10 = 96 MHz PLL divided by 4 to derive system clock 01 = 96 MHz PLL divided by 3 to derive system clock 00 = 96 MHz PLL divided by 2 to derive system clock bit 2-0 PLLDIV2:PLLDIV0: PLL Prescaler Selection bits 111 = Divide by 12 (48 MHz oscillator input) 110 = Divide by 10 (40 MHz oscillator input) 101 = Divide by 6 (24 MHz oscillator input) 100 = Divide by 5 (20 MHz oscillator input) 011 = Divide by 4 (16 MHz oscillator input) 010 = Divide by 3 (12 MHz oscillator input) 001 = Divide by 2 (8 MHz oscillator input) 000 = No prescale (4 MHz oscillator input drives PLL directly) © 2008 Microchip Technology Inc. DS39760D-page 193 PIC18F2450/4450 REGISTER 18-2: CONFIG1H: CONFIGURATION REGISTER 1 HIGH (BYTE ADDRESS 300001h) R/P-0 R/P-0 U-0 U-0 R/P-0 R/P-1 R/P-1 R/P-1 IESO FCMEN — — FOSC3(1) FOSC2(1) FOSC1(1) FOSC0(1) bit 7 bit 0 Legend: R = Readable bit P = Programmable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state bit 7 IESO: Internal/External Oscillator Switchover bit 1 = Oscillator Switchover mode enabled 0 = Oscillator Switchover mode disabled bit 6 FCMEN: Fail-Safe Clock Monitor Enable bit 1 = Fail-Safe Clock Monitor enabled 0 = Fail-Safe Clock Monitor disabled bit 5-4 Unimplemented: Read as ‘0’ bit 3-0 FOSC3:FOSC0: Oscillator Selection bits(1) 111x = HS oscillator, PLL enabled (HSPLL) 110x = HS oscillator (HS) 1011 = Internal oscillator, HS oscillator used by USB (INTHS) 1010 = Internal oscillator, XT used by USB (INTXT) 1001 = Internal oscillator, CLKO function on RA6, EC used by USB (INTCKO) 1000 = Internal oscillator, port function on RA6, EC used by USB (INTIO) 0111 = EC oscillator, PLL enabled, CLKO function on RA6 (ECPLL) 0110 = EC oscillator, PLL enabled, port function on RA6 (ECPIO) 0101 = EC oscillator, CLKO function on RA6 (EC) 0100 = EC oscillator, port function on RA6 (ECIO) 001x = XT oscillator, PLL enabled (XTPLL) 000x = XT oscillator (XT) Note 1: The microcontroller and USB module both use the selected oscillator as their clock source in XT, HS and EC modes. The USB module uses the indicated XT, HS or EC oscillator as its clock source whenever the microcontroller uses the internal oscillator. DS39760D-page 194 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 18-3: U-0 CONFIG2L: CONFIGURATION REGISTER 2 LOW (BYTE ADDRESS 300002h) U-0 — — R/P-0 VREGEN R/P-1 BORV1 (1) R/P-1 BORV0 (1) R/P-1 R/P-1 (2) BOREN1 BOREN0 bit 7 R/P-1 (2) PWRTEN(2) bit 0 Legend: R = Readable bit P = Programmable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state bit 7-6 Unimplemented: Read as ‘0’ bit 5 VREGEN: USB Internal Voltage Regulator Enable bit 1 = USB voltage regulator enabled 0 = USB voltage regulator disabled bit 4-3 BORV1:BORV0: Brown-out Reset Voltage bits(1) 11 = Minimum setting . . . 00 = Maximum setting bit 2-1 BOREN1:BOREN0: Brown-out Reset Enable bits(2) 11 = Brown-out Reset enabled in hardware only (SBOREN is disabled) 10 = Brown-out Reset enabled in hardware only and disabled in Sleep mode (SBOREN is disabled) 01 = Brown-out Reset enabled and controlled by software (SBOREN is enabled) 00 = Brown-out Reset disabled in hardware and software bit 0 PWRTEN: Power-up Timer Enable bit(2) 1 = PWRT disabled 0 = PWRT enabled Note 1: 2: See Section 21.0 “Electrical Characteristics” for the specifications. The Power-up Timer is decoupled from Brown-out Reset, allowing these features to be independently controlled. © 2008 Microchip Technology Inc. DS39760D-page 195 PIC18F2450/4450 REGISTER 18-4: U-0 CONFIG2H: CONFIGURATION REGISTER 2 HIGH (BYTE ADDRESS 300003h) U-0 — — U-0 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 — WDTPS3 WDTPS2 WDTPS1 WDTPS0 WDTEN bit 7 bit 0 Legend: R = Readable bit P = Programmable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state bit 7-5 Unimplemented: Read as ‘0’ bit 4-1 WDTPS3:WDTPS0: Watchdog Timer Postscale Select bits 1111 = 1:32,768 1110 = 1:16,384 1101 = 1:8,192 1100 = 1:4,096 1011 = 1:2,048 1010 = 1:1,024 1001 = 1:512 1000 = 1:256 0111 = 1:128 0110 = 1:64 0101 = 1:32 0100 = 1:16 0011 = 1:8 0010 = 1:4 0001 = 1:2 0000 = 1:1 bit 0 WDTEN: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled (control is placed on the SWDTEN bit) DS39760D-page 196 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 18-5: CONFIG3H: CONFIGURATION REGISTER 3 HIGH (BYTE ADDRESS 300005h) R/P-1 U-0 U-0 U-0 U-0 R/P-0 R/P-1 U-0 MCLRE — — — — LPT1OSC PBADEN — bit 7 bit 0 Legend: R = Readable bit P = Programmable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state bit 7 MCLRE: MCLR Pin Enable bit 1 = MCLR pin enabled, RA5 input pin disabled 0 = RA5 input pin enabled, MCLR pin disabled bit 6-3 Unimplemented: Read as ‘0’ bit 2 LPT1OSC: Low-Power Timer1 Oscillator Enable bit 1 = Timer1 configured for low-power operation 0 = Timer1 configured for higher power operation bit 1 PBADEN: PORTB A/D Enable bit (Affects ADCON1 Reset state. ADCON1 controls PORTB<4:0> pin configuration.) 1 = PORTB<4:0> pins are configured as analog input channels on Reset 0 = PORTB<4:0> pins are configured as digital I/O on Reset bit 0 Unimplemented: Read as ‘0’ © 2008 Microchip Technology Inc. DS39760D-page 197 PIC18F2450/4450 REGISTER 18-6: R/P-1 CONFIG4L: CONFIGURATION REGISTER 4 LOW (BYTE ADDRESS 300006h) R/P-0 XINST DEBUG R/P-0 ICPRT U-0 R/P-0 R/P-1 U-0 R/P-1 — BBSIZ LVP — STVREN (1) bit 7 bit 0 Legend: R = Readable bit P = Programmable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state bit 7 DEBUG: Background Debugger Enable bit 1 = Background debugger disabled, RB6 and RB7 configured as general purpose I/O pins 0 = Background debugger enabled, RB6 and RB7 are dedicated to In-Circuit Debug bit 6 XINST: Extended Instruction Set Enable bit 1 = Instruction set extension and Indexed Addressing mode enabled 0 = Instruction set extension and Indexed Addressing mode disabled (Legacy mode) bit 5 ICPRT: Dedicated In-Circuit Debug/Programming Port (ICPORT) Enable bit(1) 1 = ICPORT enabled 0 = ICPORT disabled bit 4 Unimplemented: Read as ‘0’ bit 3 BBSIZ: Boot Block Size Select bit 1 = 2 kW boot block size 0 = 1 kW boot block size bit 2 LVP: Single-Supply ICSP™ Enable bit 1 = Single-Supply ICSP enabled 0 = Single-Supply ICSP disabled bit 1 Unimplemented: Read as ‘0’ bit 0 STVREN: Stack Full/Underflow Reset Enable bit 1 = Stack full/underflow will cause Reset 0 = Stack full/underflow will not cause Reset Note 1: Available only on PIC18F4450 devices in 44-pin TQFP packages. Always leave this bit clear in all other devices. DS39760D-page 198 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 18-7: CONFIG5L: CONFIGURATION REGISTER 5 LOW (BYTE ADDRESS 300008h) U-0 U-0 U-0 U-0 U-0 U-0 R/C-1 R/C-1 — — — — — — CP1 CP0 bit 7 bit 0 Legend: R = Readable bit C = Clearable bit U = Unimplemented bit, read as ‘0’ -n = Value when device is unprogrammed u = Unchanged from programmed state bit 7-2 Unimplemented: Read as ‘0’ bit 1 CP1: Code Protection bit 1 = Block 1 (002000-003FFFh) is not code-protected 0 = Block 1 (002000-003FFFh) is code-protected bit 0 CP0: Code Protection bit 1 = Block 0 (000800-001FFFh) or (001000-001FFFh) is not code-protected 0 = Block 0 (000800-001FFFh) or (001000-001FFFh) is code-protected REGISTER 18-8: CONFIG5H: CONFIGURATION REGISTER 5 HIGH (BYTE ADDRESS 300009h) U-0 R/C-1 U-0 U-0 U-0 U-0 U-0 U-0 — CPB — — — — — — bit 7 bit 0 Legend: R = Readable bit C = Clearable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state bit 7 Unimplemented: Read as ‘0’ bit 6 CPB: Boot Block Code Protection bit 1 = Boot block (000000-0007FFh) or (000000-000FFFh) is not code-protected 0 = Boot block (000000-0007FFh) or (000000-000FFFh) is code-protected bit 5-0 Unimplemented: Read as ‘0’ © 2008 Microchip Technology Inc. DS39760D-page 199 PIC18F2450/4450 REGISTER 18-9: CONFIG6L: CONFIGURATION REGISTER 6 LOW (BYTE ADDRESS 30000Ah) U-0 U-0 U-0 U-0 U-0 U-0 R/C-1 R/C-1 — — — — — — WRT1 WRT0 bit 7 bit 0 Legend: R = Readable bit C = Clearable bit U = Unimplemented bit, read as ‘0’ -n = Value when device is unprogrammed u = Unchanged from programmed state bit 7-2 Unimplemented: Read as ‘0’ bit 1 WRT1: Write Protection bit 1 = Block 1 (002000-003FFFh) is not write-protected 0 = Block 1 (002000-003FFFh) is write-protected bit 0 WRT0: Write Protection bit 1 = Block 0 (000800-001FFFh) or (001000-001FFFh) is not write-protected 0 = Block 0 (000800-001FFFh) or (001000-001FFFh) is write-protected REGISTER 18-10: CONFIG6H: CONFIGURATION REGISTER 6 HIGH (BYTE ADDRESS 30000Bh) U-0 — R/C-1 R-1 U-0 U-0 U-0 U-0 U-0 WRTB WRTC(1) — — — — — bit 7 bit 0 Legend: R = Readable bit C = Clearable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state bit 7 Unimplemented: Read as ‘0’ bit 6 WRTB: Boot Block Write Protection bit 1 = Boot block (000000-0007FFh) or (000000-000FFFh) is not write-protected 0 = Boot block (000000-0007FFh) or (000000-000FFFh) is write-protected bit 5 WRTC: Configuration Register Write Protection bit(1) 1 = Configuration registers (300000-3000FFh) are not write-protected 0 = Configuration registers (300000-3000FFh) are write-protected bit 4-0 Unimplemented: Read as ‘0’ Note 1: This bit is read-only in normal execution mode; it can be written only in Program mode. DS39760D-page 200 © 2008 Microchip Technology Inc. PIC18F2450/4450 REGISTER 18-11: CONFIG7L: CONFIGURATION REGISTER 7 LOW (BYTE ADDRESS 30000Ch) U-0 U-0 U-0 U-0 U-0 U-0 R/C-1 R/C-1 — — — — — — EBTR1 EBTR0 bit 7 bit 0 Legend: R = Readable bit C = Clearable bit U = Unimplemented bit, read as ‘0’ -n = Value when device is unprogrammed u = Unchanged from programmed state bit 7-2 Unimplemented: Read as ‘0’ bit 1 EBTR1: Table Read Protection bit 1 = Block 1 (002000-003FFFh) is not protected from table reads executed in other blocks 0 = Block 1 (002000-003FFFh) is protected from table reads executed in other blocks bit 0 EBTR0: Table Read Protection bit 1 = Block 0 (000800-001FFFh) or (001000-001FFFh) is not protected from table reads executed in other blocks 0 = Block 0 (000800-001FFFh) or (001000-001FFFh) is protected from table reads executed in other blocks REGISTER 18-12: CONFIG7H: CONFIGURATION REGISTER 7 HIGH (BYTE ADDRESS 30000Dh) U-0 R/C-1 U-0 U-0 U-0 U-0 U-0 U-0 — EBTRB — — — — — — bit 7 bit 0 Legend: R = Readable bit C = Clearable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state bit 7 Unimplemented: Read as ‘0’ bit 6 EBTRB: Boot Block Table Read Protection bit 1 = Boot block (000000-0007FFh) or (000000-000FFFh) is not protected from table reads executed in other blocks 0 = Boot block (000000-0007FFh) or (000000-000FFFh) is protected from table reads executed in other blocks bit 5-0 Unimplemented: Read as ‘0’ © 2008 Microchip Technology Inc. DS39760D-page 201 PIC18F2450/4450 REGISTER 18-13: DEVID1: DEVICE ID REGISTER 1 FOR PIC18F2450/4450 DEVICES R R R R R R R R DEV2 DEV1 DEV0 REV4 REV3 REV2 REV1 REV0 bit 7 bit 0 Legend: R = Read-only bit P = Programmable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state bit 7-5 DEV2:DEV0: Device ID bits 001 = PIC18F2450 000 = PIC18F4450 bit 4-0 REV4:REV0: Revision ID bits These bits are used to indicate the device revision. REGISTER 18-14: DEVID2: DEVICE ID REGISTER 2 FOR PIC18F2450/4450 DEVICES R (1) DEV10 R R R R R R R DEV9(1) DEV8(1) DEV7(1) DEV6(1) DEV5(1) DEV4(1) DEV3(1) bit 7 bit 0 Legend: R = Read-only bit P = Programmable bit -n = Value when device is unprogrammed bit 7-0 Note 1: U = Unimplemented bit, read as ‘0’ u = Unchanged from programmed state DEV10:DEV3: Device ID bits(1) These bits are used with the DEV2:DEV0 bits in the DEVID1 register to identify the part number. 0010 0100 = PIC18F2450/4450 devices These values for DEV10:DEV3 may be shared with other devices. The specific device is always identified by using the entire DEV10:DEV0 bit sequence. DS39760D-page 202 © 2008 Microchip Technology Inc. PIC18F2450/4450 18.2 Watchdog Timer (WDT) For PIC18F2450/4450 devices, the WDT is driven by the INTRC source. When the WDT is enabled, the clock source is also enabled. The nominal WDT period is 4 ms and has the same stability as the INTRC oscillator. The 4 ms period of the WDT is multiplied by a 16-bit postscaler. Any output of the WDT postscaler is selected by a multiplexer, controlled by bits in Configuration Register 2H. Available periods range from 4 ms to 131.072 seconds (2.18 minutes). The WDT and postscaler are cleared when any of the following events occur: a SLEEP or CLRWDT instruction is executed or a clock failure has occurred. FIGURE 18-1: Note 1: The CLRWDT and SLEEP instructions clear the WDT and postscaler counts when executed. 2: When a CLRWDT instruction is executed, the postscaler count will be cleared. 18.2.1 CONTROL REGISTER Register 18-15 shows the WDTCON register. This is a readable and writable register which contains a control bit that allows software to override the WDT enable Configuration bit, but only if the Configuration bit has disabled the WDT. WDT BLOCK DIAGRAM SWDTEN WDTEN Enable WDT INTRC Control WDT Counter INTRC Source Wake-up from Power-Managed Modes ÷128 CLRWDT All Device Resets Programmable Postscaler 1:1 to 1:32,768 Reset WDT Reset WDT WDTPS<3:0> 4 SLEEP © 2008 Microchip Technology Inc. DS39760D-page 203 PIC18F2450/4450 REGISTER 18-15: WDTCON: WATCHDOG TIMER CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — SWDTEN(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-1 Unimplemented: Read as ‘0’ bit 0 SWDTEN: Software Controlled Watchdog Timer Enable bit(1) 1 = Watchdog Timer is on 0 = Watchdog Timer is off Note 1: This bit has no effect if the Configuration bit, WDTEN, is enabled. TABLE 18-2: Name RCON WDTCON x = Bit is unknown SUMMARY OF WATCHDOG TIMER REGISTERS Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page: IPEN SBOREN(1) — RI TO PD POR BOR 50 — — — — — — — SWDTEN 50 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Watchdog Timer. Note 1: The SBOREN bit is only available when BOREN<1:0> = 01; otherwise, the bit reads as ‘0’. DS39760D-page 204 © 2008 Microchip Technology Inc. PIC18F2450/4450 18.3 Two-Speed Start-up In all other power-managed modes, Two-Speed Start-up is not used. The device will be clocked by the currently selected clock source until the primary clock source becomes available. The setting of the IESO bit is ignored. The Two-Speed Start-up feature helps to minimize the latency period, from oscillator start-up to code execution, by allowing the microcontroller to use the INTRC oscillator as a clock source until the primary clock source is available. It is enabled by setting the IESO Configuration bit. 18.3.1 Two-Speed Start-up should be enabled only if the primary oscillator mode is XT, HS, XTPLL or HSPLL (Crystal-Based modes). Other sources do not require an Oscillator Start-up Timer delay; for these, Two-Speed Start-up should be disabled. While using the INTRC oscillator in Two-Speed Start-up, the device still obeys the normal command sequences for entering power-managed modes, including serial SLEEP instructions (refer to Section 3.1.4 “Multiple Sleep Commands”). In practice, this means that user code can change the SCS1:SCS0 bit settings or issue SLEEP instructions before the OST times out. This would allow an application to briefly wake-up, perform routine “housekeeping” tasks and return to Sleep before the device starts to operate from the primary oscillator. When enabled, Resets and wake-ups from Sleep mode cause the device to configure itself to run from the internal oscillator as the clock source, following the time-out of the Power-up Timer after a Power-on Reset is enabled. This allows almost immediate code execution while the primary oscillator starts and the OST is running. Once the OST times out, the device automatically switches to PRI_RUN mode. User code can also check if the primary clock source is currently providing the device clocking by checking the status of the OSTS bit (OSCCON<3>). If the bit is set, the primary oscillator is providing the clock. Otherwise, the internal oscillator is providing the clock during wake-up from Reset or Sleep mode. Because the OSCCON register is cleared on Reset events, the INTRC clock is used directly at its base frequency. FIGURE 18-2: SPECIAL CONSIDERATIONS FOR USING TWO-SPEED START-UP TIMING TRANSITION FOR TWO-SPEED START-UP (INTRC TO HSPLL) Q1 Q2 Q3 Q4 Q2 Q3 Q4 Q1 Q2 Q3 Q1 INTRC OSC1 TOST(1) TPLL(1) 1 PLL Clock Output 2 n-1 n Clock Transition CPU Clock Peripheral Clock Program Counter PC Wake from Interrupt Event Note 1: PC + 2 PC + 4 PC + 6 OSTS bit Set TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale. © 2008 Microchip Technology Inc. DS39760D-page 205 PIC18F2450/4450 18.4 Fail-Safe Clock Monitor The Fail-Safe Clock Monitor (FSCM) allows the microcontroller to continue operation in the event of an external oscillator failure by automatically switching the device clock to the internal oscillator. The FSCM function is enabled by setting the FCMEN Configuration bit. When FSCM is enabled, the INTRC oscillator runs at all times to monitor clocks to peripherals and provide a backup clock in the event of a clock failure. Clock monitoring (shown in Figure 18-3) is accomplished by creating a sample clock signal, which is the INTRC output divided by 64. This allows ample time between FSCM sample clocks for a peripheral clock edge to occur. The peripheral device clock and the sample clock are presented as inputs to the Clock Monitor latch (CM). The CM is set on the falling edge of the device clock source, but cleared on the rising edge of the sample clock. FIGURE 18-3: FSCM BLOCK DIAGRAM Clock Monitor Latch (CM) (edge-triggered) Peripheral Clock INTRC Source (32 μs) ÷ 64 488 Hz (2.048 ms) S Q C Q Clock Failure Detected Clock failure is tested for on the falling edge of the sample clock. If a sample clock falling edge occurs while CM is still set, a clock failure has been detected (Figure 18-4). This causes the following: The FSCM will detect failures of the primary or secondary clock sources only. If the internal oscillator fails, no failure would be detected, nor would any action be possible. 18.4.1 FSCM AND THE WATCHDOG TIMER Both the FSCM and the WDT are clocked by the INTRC oscillator. Since the WDT operates with a separate divider and counter, disabling the WDT has no effect on the operation of the INTRC oscillator when the FSCM is enabled. If the WDT is enabled with a small prescale value, a decrease in clock speed allows a WDT time-out to occur and a subsequent device Reset. For this reason, Fail-Safe Clock Monitor events also reset the WDT and postscaler, allowing it to start timing from when execution speed was changed and decreasing the likelihood of an erroneous time-out. 18.4.2 EXITING FAIL-SAFE OPERATION The fail-safe condition is terminated by either a device Reset or by entering a power-managed mode. On Reset, the controller starts the primary clock source specified in Configuration Register 1H (with any startup delays that are required for the oscillator mode, such as OST or PLL timer). The INTRC provides the device clock until the primary clock source becomes ready (similar to a Two-Speed Start-up). The clock source is then switched to the primary clock (indicated by the OSTS bit in the OSCCON register becoming set). The Fail-Safe Clock Monitor then resumes monitoring the peripheral clock. The primary clock source may never become ready during start-up. In this case, operation is clocked by the INTRC. The OSCCON register will remain in its Reset state until a power-managed mode is entered. • the FSCM generates an oscillator fail interrupt by setting bit, OSCFIF (PIR2<7>); • the device clock source is switched to the internal oscillator (OSCCON is not updated to show the current clock source – this is the fail-safe condition); and • the WDT is reset. DS39760D-page 206 © 2008 Microchip Technology Inc. PIC18F2450/4450 FIGURE 18-4: FSCM TIMING DIAGRAM Sample Clock Oscillator Failure Device Clock Output CM Output (Q) Failure Detected OSCFIF CM Test Note: 18.4.3 CM Test The device clock is normally at a much higher frequency than the sample clock. The relative frequencies in this example have been chosen for clarity. FSCM INTERRUPTS IN POWER-MANAGED MODES By entering a power-managed mode, the clock multiplexer selects the clock source selected by the OSCCON register. Fail-Safe Clock Monitoring of the powermanaged clock source resumes in the power-managed mode. If an oscillator failure occurs during power-managed operation, the subsequent events depend on whether or not the oscillator failure interrupt is enabled. If enabled (OSCFIF = 1), code execution will be clocked by the INTRC. An automatic transition back to the failed clock source will not occur. If the interrupt is disabled, subsequent interrupts while in Idle mode will cause the CPU to begin executing instructions while being clocked by the INTRC source. 18.4.4 CM Test POR OR WAKE-UP FROM SLEEP The FSCM is designed to detect oscillator failure at any point after the device has exited Power-on Reset (POR) or low-power Sleep mode. When the primary device clock is either EC or INTRC, monitoring can begin immediately following these events. considerably longer than the FCSM sample clock time, a false clock failure may be detected. To prevent this, the internal oscillator is automatically configured as the device clock and functions until the primary clock is stable (the OST and PLL timers have timed out). This is identical to Two-Speed Start-up mode. Once the primary clock is stable, the INTRC returns to its role as the FSCM source. Note: The same logic that prevents false oscillator failure interrupts on POR or wake from Sleep will also prevent the detection of the oscillator’s failure to start at all following these events. This can be avoided by monitoring the OSTS bit and using a timing routine to determine if the oscillator is taking too long to start. Even so, no oscillator failure interrupt will be flagged. As noted in Section 18.3.1 “Special Considerations for Using Two-Speed Start-up”, it is also possible to select another clock configuration and enter an alternate power-managed mode while waiting for the primary clock to become stable. When the new power-managed mode is selected, the primary clock is disabled. For oscillator modes involving a crystal or resonator (HS, HSPLL or XT), the situation is somewhat different. Since the oscillator may require a start-up time © 2008 Microchip Technology Inc. DS39760D-page 207 PIC18F2450/4450 18.5 Program Verification and Code Protection Each of the three blocks has three code protection bits associated with them. They are: The overall structure of the code protection on the PIC18 Flash devices differs significantly from other PIC® microcontrollers. • Code-Protect bit (CPx) • Write-Protect bit (WRTx) • External Block Table Read bit (EBTRx) The user program memory is divided into three blocks. One of these is a boot block of 1 or 2 Kbytes. The remainder of the memory is divided into two blocks on binary boundaries. Figure 18-5 shows the program memory organization for 24 and 32-Kbyte devices and the specific code protection bit associated with each block. The actual locations of the bits are summarized in Table 18-3. FIGURE 18-5: CODE-PROTECTED PROGRAM MEMORY FOR PIC18F2450/4450 MEMORY SIZE/DEVICE 16 Kbytes (PIC18F2450/4450) Address Range Boot Block 000000h 0007FFh 000FFFh Block Code Protection Controlled By: CPB, WRTB, EBTRB 001000h Block 0 CP0, WRT0, EBTR0 001FFFh 002000h Block 1 CP1, WRT1, EBTR1 003FFFh Unimplemented Read ‘0’s Unimplemented Read ‘0’s Unimplemented Read ‘0’s (Unimplemented Memory Space) 1FFFFFh TABLE 18-3: SUMMARY OF CODE PROTECTION REGISTERS File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 300008h CONFIG5L — — — — — — CP1 CP0 300009h CONFIG5H — CPB — — — — — — 30000Ah CONFIG6L — — — — — — WRT1 WRT0 30000Bh CONFIG6H — WRTB WRTC — — — — — 30000Ch CONFIG7L — — — — — — EBTR1 EBTR0 30000Dh CONFIG7H — EBTRB — — — — — — Legend: Shaded cells are unimplemented. DS39760D-page 208 © 2008 Microchip Technology Inc. PIC18F2450/4450 18.5.1 PROGRAM MEMORY CODE PROTECTION The program memory may be read to or written from any location using the table read and table write instructions. The device ID may be read with table reads. The Configuration registers may be read and written with the table read and table write instructions. A table read instruction that executes from a location outside of that block is not allowed to read and will result in reading ‘0’s. Figure 18-6 through Figure 18-8 illustrate table write and table read protection. Note: In normal execution mode, the CPx bits have no direct effect. CPx bits inhibit external reads and writes. A block of user memory may be protected from table writes if the WRTx Configuration bit is ‘0’. The EBTRx bits control table reads. For a block of user memory with the EBTRx bit set to ‘0’, a table read instruction that executes from within that block is allowed to read. FIGURE 18-6: Code protection bits may only be written to a ‘0’ from a ‘1’ state. It is not possible to write a ‘1’ to a bit in the ‘0’ state. Code protection bits are only set to ‘1’ by a full Chip Erase or Block Erase function. The full Chip Erase and Block Erase functions can only be initiated via ICSP operation or an external programmer. TABLE WRITE (WRTx) DISALLOWED Register Values Program Memory Configuration Bit Settings 000000h 0007FFh 000FFFh 001000h TBLPTR = 0008FFh PC = 001FFEh WRTB, EBTRB = 11 WRT0, EBTR0 = 01 TBLWT* 001FFFh 002000h WRT1, EBTR1 = 11 003FFFh WRT2, EBTR2 = 11 WRT3, EBTR3 = 11 Results: All table writes disabled to Blockn whenever WRTx = 0. © 2008 Microchip Technology Inc. DS39760D-page 209 PIC18F2450/4450 FIGURE 18-7: EXTERNAL BLOCK TABLE READ (EBTRx) DISALLOWED Register Values Program Memory Configuration Bit Settings 000000h 0007FFh 000FFFh 001000h WRTB, EBTRB = 11 WRT0, EBTR0 = 10 TBLPTR = 0008FFh 001FFFh 002000h WRT1, EBTR1 = 11 PC = 003FFEh TBLRD* 003FFFh Results: All table reads from external blocks to Blockn are disabled whenever EBTRx = 0. TABLAT register returns a value of ‘0’. FIGURE 18-8: EXTERNAL BLOCK TABLE READ (EBTRx) ALLOWED Register Values Program Memory Configuration Bit Settings 000000h 0007FFh 000FFFh 001000h TBLPTR = 0008FFh WRTB, EBTRB = 11 WRT0, EBTR0 = 10 PC = 001FFEh TBLRD* 001FFFh 002000h WRT1, EBTR1 = 11 003FFFh Results: Table reads permitted within Blockn, even when EBTRBx = 0. TABLAT register returns the value of the data at the location TBLPTR. DS39760D-page 210 © 2008 Microchip Technology Inc. PIC18F2450/4450 18.5.2 CONFIGURATION REGISTER PROTECTION The Configuration registers can be write-protected. The WRTC bit controls protection of the Configuration registers. In normal execution mode, the WRTC bit is readable only. WRTC can only be written via ICSP operation or an external programmer. 18.6 18.9 ID Locations Eight memory locations (200000h-200007h) are designated as ID locations, where the user can store checksum or other code identification numbers. These locations are both readable and writable during normal execution through the TBLRD and TBLWT instructions or during program/verify. The ID locations can be read when the device is code-protected. 18.7 In-Circuit Serial Programming PIC18F2450/4450 microcontrollers can be serially programmed while in the end application circuit. This is simply done with two lines for clock and data and three other lines for power, ground and the programming voltage. This allows customers to manufacture boards with unprogrammed devices and then program the microcontroller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. 18.8 To use the In-Circuit Debugger function of the microcontroller, the design must implement In-Circuit Serial Programming connections to MCLR/VPP/RE3, VDD, VSS, RB7 and RB6. This will interface to the In-Circuit Debugger module available from Microchip or one of the third party development tool companies. In-Circuit Debugger When the DEBUG Configuration bit is programmed to a ‘0’, the In-Circuit Debugger functionality is enabled. This function allows simple debugging functions when used with MPLAB® IDE. When the microcontroller has this feature enabled, some resources are not available for general use. Table 18-4 shows which resources are required by the background debugger. TABLE 18-4: DEBUGGER RESOURCES I/O pins: RB6, RB7 Stack: 2 levels Program Memory: 512 bytes Data Memory: 10 bytes Special ICPORT Features (Designated Packages Only) Under specific circumstances, the No Connect (NC) pins of PIC18F4450 devices in 44-pin TQFP packages can provide additional functionality. These features are controlled by device Configuration bits and are available only in this package type and pin count. 18.9.1 DEDICATED ICD/ICSP PORT The 44-pin TQFP devices can use NC pins to provide an alternate port for In-Circuit Debugging (ICD) and InCircuit Serial Programming (ICSP). These pins are collectively known as the dedicated ICSP/ICD port, since they are not shared with any other function of the device. When implemented, the dedicated port activates three NC pins to provide an alternate device Reset, data and clock ports. None of these ports overlap with standard I/O pins, making the I/O pins available to the user’s application. The dedicated ICSP/ICD port is enabled by setting the ICPRT Configuration bit. The port functions the same way as the legacy ICSP/ICD port on RB6/RB7. Table 18-5 identifies the functionally equivalent pins for ICSP and ICD purposes. TABLE 18-5: Pin Name Legacy Port Dedicated Port Pin Type Pin Function MCLR/VPP/ RE3 NC/ICRST/ ICVPP P Device Reset and Programming Enable RB6/KBI2/ PGC NC/ICCK/ ICPGC I Serial Clock RB7/KBI3/ PGD NC/ICDT/ ICPGD I/O Serial Data Legend: © 2008 Microchip Technology Inc. EQUIVALENT PINS FOR LEGACY AND DEDICATED ICD/ICSP™ PORTS I = Input, O = Output, P = Power DS39760D-page 211 PIC18F2450/4450 Even when the dedicated port is enabled, the ICSP and ICD functions remain available through the legacy port. When VIHH is seen on the MCLR/VPP/RE3 pin, the state of the ICRST/ICVPP pin is ignored. Note 1: The ICPRT Configuration bit can only be programmed through the default ICSP port. 2: The ICPRT Configuration bit must be maintained clear for all 28-pin and 40-pin devices; otherwise, unexpected operation may occur. 18.9.2 28-PIN EMULATION PIC18F4450 devices in 44-pin TQFP packages also have the ability to change their configuration under external control for debugging purposes. This allows the device to behave as if it were a PIC18F2450/4450 28-pin device. This 28-pin Configuration mode is controlled through a single pin, NC/ICPORTS. Connecting this pin to VSS forces the device to function as a 28-pin device. Features normally associated with the 40/44-pin devices are disabled, along with their corresponding control registers and bits. On the other hand, connecting the pin to VDD forces the device to function in its default configuration. The configuration option is only available when background debugging and the dedicated ICD/ICSP port are both enabled (DEBUG Configuration bit is clear and ICPRT Configuration bit is set). When disabled, NC/ICPORTS is a No Connect pin. 18.10 Single-Supply ICSP Programming The LVP Configuration bit enables Single-Supply ICSP Programming (formerly known as Low-Voltage ICSP Programming or LVP). When Single-Supply Programming is enabled, the microcontroller can be programmed without requiring high voltage being applied to the MCLR/VPP/RE3 pin, but the RB5/KBI1/ PGM pin is then dedicated to controlling Program mode entry and is not available as a general purpose I/O pin. Note 1: High-Voltage Programming is always available, regardless of the state of the LVP bit, by applying VIHH to the MCLR pin. 2: While in Low-Voltage ICSP Programming mode, the RB5 pin can no longer be used as a general purpose I/O pin and should be held low during normal operation. 3: When using Low-Voltage ICSP Programming (LVP) and the pull-ups on PORTB are enabled, bit 5 in the TRISB register must be cleared to disable the pull-up on RB5 and ensure the proper operation of the device. 4: If the device Master Clear is disabled, verify that either of the following is done to ensure proper entry into ICSP mode: a) Disable Low-Voltage Programming (CONFIG4L<2> = 0); or b) Make certain that RB5/KBI1/PGM is held low during entry into ICSP. If Single-Supply ICSP Programming mode will not be used, the LVP bit can be cleared. RB5/KBI1/PGM then becomes available as the digital I/O pin, RB5. The LVP bit may be set or cleared only when using standard high-voltage programming (VIHH applied to the MCLR/ VPP/RE3 pin). Once LVP has been disabled, only the standard high-voltage programming is available and must be used to program the device. Memory that is not code-protected can be erased using either a Block Erase, or erased row by row, then written at any specified VDD. If code-protected memory is to be erased, a Block Erase is required. If a Block Erase is to be performed when using Low-Voltage Programming, the device must be supplied with VDD of 4.5V to 5.5V. While programming using Single-Supply Programming, VDD is applied to the MCLR/VPP/RE3 pin as in normal execution mode. To enter Programming mode, VDD is applied to the PGM pin. DS39760D-page 212 © 2008 Microchip Technology Inc. PIC18F2450/4450 19.0 INSTRUCTION SET SUMMARY PIC18F2450/4450 devices incorporate the standard set of 75 PIC18 core instructions, as well as an extended set of eight new instructions for the optimization of code that is recursive or that utilizes a software stack. The extended set is discussed later in this section. 19.1 Standard Instruction Set The standard PIC18 instruction set adds many enhancements to the previous PIC MCU instruction sets, while maintaining an easy migration from these PIC MCU instruction sets. Most instructions are a single program memory word (16 bits) but there are four instructions that require two program memory locations. Each single-word instruction is a 16-bit word divided into an opcode, which specifies the instruction type and one or more operands, which further specify the operation of the instruction. The instruction set is highly orthogonal and is grouped into four basic categories: • • • • Byte-oriented operations Bit-oriented operations Literal operations Control operations The PIC18 instruction set summary in Table 19-2 lists byte-oriented, bit-oriented, literal and control operations. Table 19-1 shows the opcode field descriptions. Most byte-oriented instructions have three operands: 1. 2. 3. The file register (specified by ‘f’) The destination of the result (specified by ‘d’) The accessed memory (specified by ‘a’) The file register designator, ‘f’, specifies which file register is to be used by the instruction. The destination designator, ‘d’, specifies where the result of the operation is to be placed. If ‘d’ is ‘0’, the result is placed in the WREG register. If ‘d’ is ‘1’, the result is placed in the file register specified in the instruction. All bit-oriented instructions have three operands: 1. 2. 3. The file register (specified by ‘f’) The bit in the file register (specified by ‘b’) The accessed memory (specified by ‘a’) The literal instructions may use some of the following operands: • A literal value to be loaded into a file register (specified by ‘k’) • The desired FSR register to load the literal value into (specified by ‘f’) • No operand required (specified by ‘—’) The control instructions may use some of the following operands: • A program memory address (specified by ‘n’) • The mode of the CALL or RETURN instructions (specified by ‘s’) • The mode of the table read and table write instructions (specified by ‘m’) • No operand required (specified by ‘—’) All instructions are a single word, except for four double-word instructions. These instructions were made double-word to contain the required information in 32 bits. In the second word, the 4 MSbs are ‘1’s. If this second word is executed as an instruction (by itself), it will execute as a NOP. All single-word instructions are executed in a single instruction cycle, unless a conditional test is true or the program counter is changed as a result of the instruction. In these cases, the execution takes two instruction cycles with the additional instruction cycle(s) executed as a NOP. The double-word instructions execute in two instruction cycles. One instruction cycle consists of four oscillator periods. Thus, for an oscillator frequency of 4 MHz, the normal instruction execution time is 1 μs. If a conditional test is true, or the program counter is changed as a result of an instruction, the instruction execution time is 2 μs. Two-word branch instructions (if true) would take 3 μs. Figure 19-1 shows the general formats that the instructions can have. All examples use the convention ‘nnh’ to represent a hexadecimal number. The instruction set summary, shown in Table 19-2, lists the standard instructions recognized by the Microchip MPASMTM Assembler. Section 19.1.1 “Standard Instruction Set” provides a description of each instruction. The bit field designator ‘b’ selects the number of the bit affected by the operation, while the file register designator, ‘f’, represents the number of the file in which the bit is located. © 2008 Microchip Technology Inc. DS39760D-page 213 PIC18F2450/4450 TABLE 19-1: OPCODE FIELD DESCRIPTIONS Field Description a RAM access bit a = 0: RAM location in Access RAM (BSR register is ignored) a = 1: RAM bank is specified by BSR register bbb Bit address within an 8-bit file register (0 to 7). BSR Bank Select Register. Used to select the current RAM bank. C, DC, Z, OV, N ALU Status bits: Carry, Digit Carry, Zero, Overflow, Negative. d Destination select bit d = 0: store result in WREG d = 1: store result in file register f dest Destination: either the WREG register or the specified register file location. f 8-bit register file address (00h to FFh) or 2-bit FSR designator (0h to 3h). fs 12-bit register file address (000h to FFFh). This is the source address. fd 12-bit register file address (000h to FFFh). This is the destination address. GIE Global Interrupt Enable bit. k Literal field, constant data or label (may be either an 8-bit, 12-bit or a 20-bit value). label Label name. mm The mode of the TBLPTR register for the table read and table write instructions. Only used with table read and table write instructions: * No change to register (such as TBLPTR with table reads and writes) *+ Post-Increment register (such as TBLPTR with table reads and writes) *- Post-Decrement register (such as TBLPTR with table reads and writes) Pre-Increment register (such as TBLPTR with table reads and writes) +* n The relative address (2’s complement number) for relative branch instructions or the direct address for Call/Branch and Return instructions. PC Program Counter. PCL Program Counter Low Byte. PCH Program Counter High Byte. PCLATH Program Counter High Byte Latch. PCLATU Program Counter Upper Byte Latch. PD Power-Down bit. PRODH Product of Multiply High Byte. PRODL Product of Multiply Low Byte. s Fast Call/Return mode select bit s = 0: do not update into/from shadow registers s = 1: certain registers loaded into/from shadow registers (Fast mode) TBLPTR 21-bit Table Pointer (points to a program memory location). TABLAT 8-bit Table Latch. TO Time-out bit. TOS Top-of-Stack. u Unused or unchanged. WDT Watchdog Timer. WREG Working register (accumulator). x Don’t care (‘0’ or ‘1’). The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. zs 7-bit offset value for indirect addressing of register files (source). 7-bit offset value for indirect addressing of register files (destination). zd { } Optional argument. [text] Indicates an indexed address. (text) The contents of text. [expr]<n> Specifies bit n of the register indicated by the pointer, expr. → Assigned to. < > Register bit field. ∈ In the set of. italics User-defined term (font is Courier New). DS39760D-page 214 © 2008 Microchip Technology Inc. PIC18F2450/4450 FIGURE 19-1: GENERAL FORMAT FOR INSTRUCTIONS Byte-oriented file register operations 15 10 9 OPCODE Example Instruction 8 7 d 0 a ADDWF MYREG, W, B f (FILE #) d = 0 for result destination to be WREG register d = 1 for result destination to be file register (f) a = 0 to force Access Bank a = 1 for BSR to select bank f = 8-bit file register address Byte to Byte move operations (2-word) 15 12 11 0 OPCODE 15 MOVFF MYREG1, MYREG2 f (Source FILE #) 12 11 0 f (Destination FILE #) 1111 f = 12-bit file register address Bit-oriented file register operations 15 12 11 9 8 7 0 OPCODE b (BIT #) a BSF MYREG, bit, B f (FILE #) b = 3-bit position of bit in file register (f) a = 0 to force Access Bank a = 1 for BSR to select bank f = 8-bit file register address Literal operations 15 8 7 0 OPCODE MOVLW 7Fh k (literal) k = 8-bit immediate value Control operations CALL, GOTO and Branch operations 15 8 7 0 OPCODE 15 GOTO Label n<7:0> (literal) 12 11 0 n<19:8> (literal) 1111 n = 20-bit immediate value 15 8 7 S OPCODE 15 0 CALL MYFUNC n<7:0> (literal) 12 11 0 n<19:8> (literal) 1111 S = Fast bit 15 11 10 OPCODE 15 0 8 7 OPCODE © 2008 Microchip Technology Inc. BRA MYFUNC n<10:0> (literal) 0 n<7:0> (literal) BC MYFUNC DS39760D-page 215 PIC18F2450/4450 TABLE 19-2: PIC18FXXXX INSTRUCTION SET Mnemonic, Operands Description Cycles 16-Bit Instruction Word MSb LSb Status Affected Notes BYTE-ORIENTED OPERATIONS ADDWF ADDWFC ANDWF CLRF COMF CPFSEQ CPFSGT CPFSLT DECF DECFSZ DCFSNZ INCF INCFSZ INFSNZ IORWF MOVF MOVFF f, d, a f, d, a f, d, a f, a f, d, a f, a f, a f, a f, d, a f, d, a f, d, a f, d, a f, d, a f, d, a f, d, a f, d, a fs, fd MOVWF MULWF NEGF RLCF RLNCF RRCF RRNCF SETF SUBFWB f, a f, a f, a f, d, a f, d, a f, d, a f, d, a f, a f, d, a SUBWF SUBWFB f, d, a f, d, a SWAPF TSTFSZ XORWF f, d, a f, a f, d, a Note 1: 2: 3: 4: Add WREG and f Add WREG and Carry bit to f AND WREG with f Clear f Complement f Compare f with WREG, Skip = Compare f with WREG, Skip > Compare f with WREG, Skip < Decrement f Decrement f, Skip if 0 Decrement f, Skip if Not 0 Increment f Increment f, Skip if 0 Increment f, Skip if Not 0 Inclusive OR WREG with f Move f Move fs (source) to 1st word fd (destination) 2nd word Move WREG to f Multiply WREG with f Negate f Rotate Left f through Carry Rotate Left f (No Carry) Rotate Right f through Carry Rotate Right f (No Carry) Set f Subtract f from WREG with Borrow Subtract WREG from f Subtract WREG from f with Borrow Swap Nibbles in f Test f, Skip if 0 Exclusive OR WREG with f 1 1 1 1 1 1 (2 or 3) 1 (2 or 3) 1 (2 or 3) 1 1 (2 or 3) 1 (2 or 3) 1 1 (2 or 3) 1 (2 or 3) 1 1 2 C, DC, Z, OV, N C, DC, Z, OV, N Z, N Z Z, N None None None C, DC, Z, OV, N None None C, DC, Z, OV, N None None Z, N Z, N None 1, 2 1, 2 1,2 2 1, 2 4 4 1, 2 1, 2, 3, 4 1, 2, 3, 4 1, 2 1, 2, 3, 4 4 1, 2 1, 2 1 1 1 1 1 1 1 1 1 1 0010 0010 0001 0110 0001 0110 0110 0110 0000 0010 0100 0010 0011 0100 0001 0101 1100 1111 0110 0000 0110 0011 0100 0011 0100 0110 0101 01da 00da 01da 101a 11da 001a 010a 000a 01da 11da 11da 10da 11da 10da 00da 00da ffff ffff 111a 001a 110a 01da 01da 00da 00da 100a 01da ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff 1 1 0101 0101 11da 10da ffff ffff ffff C, DC, Z, OV, N ffff C, DC, Z, OV, N 1, 2 1 0011 1 (2 or 3) 0110 1 0001 10da 011a 10da ffff ffff ffff ffff None ffff None ffff Z, N 4 1, 2 None None C, DC, Z, OV, N C, Z, N Z, N C, Z, N Z, N None C, DC, Z, OV, N 1, 2 1, 2 1, 2 When a PORT register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as an input and is driven low by an external device, the data will be written back with a ‘0’. If this instruction is executed on the TMR0 register (and where applicable, ‘d’ = 1), the prescaler will be cleared if assigned. If the Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all program memory locations have a valid instruction. DS39760D-page 216 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 19-2: PIC18FXXXX INSTRUCTION SET (CONTINUED) Mnemonic, Operands Description Cycles 16-Bit Instruction Word MSb LSb Status Affected Notes BIT-ORIENTED OPERATIONS BCF BSF BTFSC BTFSS BTG f, b, a f, b, a f, b, a f, b, a f, d, a Bit Clear f Bit Set f Bit Test f, Skip if Clear Bit Test f, Skip if Set Bit Toggle f 1 1 1 (2 or 3) 1 (2 or 3) 1 1001 1000 1011 1010 0111 bbba bbba bbba bbba bbba ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff None None None None None 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 2 1 (2) 2 0010 0110 0011 0111 0101 0001 0100 0nnn 0000 110s kkkk 0000 0000 1111 kkkk 0000 xxxx 0000 0000 1nnn 0000 0000 nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn kkkk kkkk 0000 0000 kkkk kkkk 0000 xxxx 0000 0000 nnnn 1111 0001 nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn kkkk kkkk 0100 0111 kkkk kkkk 0000 xxxx 0110 0101 nnnn 1111 000s None None None None None None None None None None 1 1 1 1 2 1 2 1110 1110 1110 1110 1110 1110 1110 1101 1110 1110 1111 0000 0000 1110 1111 0000 1111 0000 0000 1101 0000 0000 2 2 1 0000 0000 0000 1100 0000 0000 kkkk 0001 0000 1, 2 1, 2 3, 4 3, 4 1, 2 CONTROL OPERATIONS BC BN BNC BNN BNOV BNZ BOV BRA BZ CALL n n n n n n n n n n, s CLRWDT DAW GOTO — — n NOP NOP POP PUSH RCALL RESET RETFIE — — — — n s Branch if Carry Branch if Negative Branch if Not Carry Branch if Not Negative Branch if Not Overflow Branch if Not Zero Branch if Overflow Branch Unconditionally Branch if Zero Call Subroutine 1st word 2nd word Clear Watchdog Timer Decimal Adjust Wreg Go To Address 1st word 2nd word No Operation No Operation Pop Top of Return Stack (TOS) Push Top of Return Stack (TOS) Relative Call Software Device Reset Return from Interrupt Enable RETLW RETURN SLEEP k s — Return with Literal in WREG Return from Subroutine Go into Standby mode Note 1: 2: 3: 4: 1 1 2 TO, PD C None None None None None None All GIE/GIEH, PEIE/GIEL kkkk None 001s None 0011 TO, PD 4 When a PORT register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as an input and is driven low by an external device, the data will be written back with a ‘0’. If this instruction is executed on the TMR0 register (and where applicable, ‘d’ = 1), the prescaler will be cleared if assigned. If the Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all program memory locations have a valid instruction. © 2008 Microchip Technology Inc. DS39760D-page 217 PIC18F2450/4450 TABLE 19-2: PIC18FXXXX INSTRUCTION SET (CONTINUED) Mnemonic, Operands Description Cycles 16-Bit Instruction Word MSb LSb Status Affected Notes LITERAL OPERATIONS ADDLW ANDLW IORLW LFSR k k k f, k MOVLB MOVLW MULLW RETLW SUBLW XORLW k k k k k k Add Literal and WREG AND Literal with WREG Inclusive OR Literal with WREG Move Literal (12-bit) 2nd word to FSR(f) 1st word Move Literal to BSR<3:0> Move Literal to WREG Multiply Literal with WREG Return with Literal in WREG Subtract WREG from Literal Exclusive OR Literal with WREG 1 1 1 2 1 1 1 2 1 1 0000 0000 0000 1110 1111 0000 0000 0000 0000 0000 0000 1111 1011 1001 1110 0000 0001 1110 1101 1100 1000 1010 kkkk kkkk kkkk 00ff kkkk 0000 kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk C, DC, Z, OV, N Z, N Z, N None 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 1000 1001 1010 1011 1100 1101 1110 1111 None None None None None None None None None None None None C, DC, Z, OV, N Z, N DATA MEMORY ↔ PROGRAM MEMORY OPERATIONS TBLRD* TBLRD*+ TBLRD*TBLRD+* TBLWT* TBLWT*+ TBLWT*TBLWT+* Note 1: 2: 3: 4: Table Read 2 Table Read with Post-Increment Table Read with Post-Decrement Table Read with Pre-Increment Table Write 2 Table Write with Post-Increment Table Write with Post-Decrement Table Write with Pre-Increment When a PORT register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as an input and is driven low by an external device, the data will be written back with a ‘0’. If this instruction is executed on the TMR0 register (and where applicable, ‘d’ = 1), the prescaler will be cleared if assigned. If the Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all program memory locations have a valid instruction. DS39760D-page 218 © 2008 Microchip Technology Inc. PIC18F2450/4450 19.1.1 STANDARD INSTRUCTION SET ADDLW ADD Literal to W ADDWF Syntax: ADDLW Syntax: ADDWF Operands: 0 ≤ k ≤ 255 Operands: Operation: (W) + k → W Status Affected: N, OV, C, DC, Z 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (W) + (f) → dest Status Affected: N, OV, C, DC, Z Encoding: 0000 Description: k 1111 kkkk kkkk The contents of W are added to the 8-bit literal ‘k’ and the result is placed in W. Words: 1 Cycles: 1 ADD W to f Encoding: 0010 Q1 Q2 Q3 Q4 Read literal ‘k’ Process Data Write to W Example: ADDLW ffff ffff Add W to register ‘f’. If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 15h Before Instruction W = 10h After Instruction W = 25h 01da Description: Q Cycle Activity: Decode f {,d {,a}} Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: ADDWF REG, 0, 0 Before Instruction W = REG = After Instruction W REG Note: = = 17h 0C2h 0D9h 0C2h All PIC18 instructions may take an optional label argument, preceding the instruction mnemonic, for use in symbolic addressing. If a label is used, the instruction format then becomes: {label} instruction argument(s). © 2008 Microchip Technology Inc. DS39760D-page 219 PIC18F2450/4450 ADDWFC ADD W and Carry bit to f ANDLW AND Literal with W Syntax: ADDWFC Syntax: ANDLW Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] f {,d {,a}} Operation: (W) + (f) + (C) → dest Status Affected: N, OV, C, DC, Z Encoding: 0010 Description: 00da ffff Add W, the Carry flag and data memory location ‘f’. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed in data memory location ‘f’. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Operands: 0 ≤ k ≤ 255 Operation: (W) .AND. k → W Status Affected: N, Z Encoding: ffff k 0000 1011 kkkk kkkk Description: The contents of W are ANDed with the 8-bit literal ‘k’. The result is placed in W. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write to W Example: ANDLW Before Instruction W = After Instruction W = 05Fh A3h 03h Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: ADDWFC Before Instruction Carry bit = REG = W = After Instruction Carry bit = REG = W = DS39760D-page 220 REG, 0, 1 1 02h 4Dh 0 02h 50h © 2008 Microchip Technology Inc. PIC18F2450/4450 ANDWF AND W with f BC Branch if Carry Syntax: ANDWF Syntax: BC Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] f {,d {,a}} Operation: (W) .AND. (f) → dest Status Affected: N, Z Encoding: 0001 Description: ffff ffff The contents of W are ANDed with register ‘f’. If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: ANDWF Before Instruction W = REG = After Instruction W = REG = Operands: -128 ≤ n ≤ 127 Operation: if Carry bit is ‘1’, (PC) + 2 + 2n → PC Status Affected: None Encoding: 01da REG, 0, 0 17h C2h 02h C2h © 2008 Microchip Technology Inc. n 1110 0010 nnnn nnnn Description: If the Carry bit is ‘1’, then the program will branch. The 2’s complement number ‘2n’ is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Cycles: 1(2) Q Cycle Activity: If Jump: Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data Write to PC No operation No operation No operation No operation If No Jump: Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data No operation Example: HERE Before Instruction PC After Instruction If Carry PC If Carry PC BC 5 = address (HERE) = = = = 1; address (HERE + 12) 0; address (HERE + 2) DS39760D-page 221 PIC18F2450/4450 BCF Bit Clear f BN Branch if Negative Syntax: BCF Syntax: BN Operands: 0 ≤ f ≤ 255 0≤b≤7 a ∈ [0,1] f, b {,a} Operation: 0 → f<b> Status Affected: None Encoding: Description: bbba ffff ffff Bit ‘b’ in register ‘f’ is cleared. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write register ‘f’ Example: BCF Before Instruction FLAG_REG = After Instruction FLAG_REG = DS39760D-page 222 Operands: -128 ≤ n ≤ 127 Operation: if Negative bit is ‘1’, (PC) + 2 + 2n → PC Status Affected: None Encoding: 1001 FLAG_REG, 7, 0 n 1110 0110 nnnn nnnn Description: If the Negative bit is ‘1’, then the program will branch. The 2’s complement number ‘2n’ is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Cycles: 1(2) Q Cycle Activity: If Jump: Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data Write to PC No operation No operation No operation No operation If No Jump: Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data No operation C7h 47h Example: HERE Before Instruction PC After Instruction If Negative PC If Negative PC BN Jump = address (HERE) = = = = 1; address (Jump) 0; address (HERE + 2) © 2008 Microchip Technology Inc. PIC18F2450/4450 BNC Branch if Not Carry BNN Branch if Not Negative Syntax: BNC Syntax: BNN n n Operands: -128 ≤ n ≤ 127 Operands: -128 ≤ n ≤ 127 Operation: if Carry bit is ‘0’, (PC) + 2 + 2n → PC Operation: if Negative bit is ‘0’, (PC) + 2 + 2n → PC Status Affected: None Status Affected: None Encoding: 1110 0011 nnnn nnnn Encoding: 1110 0111 nnnn nnnn Description: If the Carry bit is ‘0’, then the program will branch. The 2’s complement number ‘2n’ is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Description: If the Negative bit is ‘0’, then the program will branch. The 2’s complement number ‘2n’ is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Words: 1 Cycles: 1(2) Cycles: 1(2) Q Cycle Activity: If Jump: Q Cycle Activity: If Jump: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data Write to PC Decode Read literal ‘n’ Process Data Write to PC No operation No operation No operation No operation No operation No operation No operation No operation Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data No operation Decode Read literal ‘n’ Process Data No operation If No Jump: Example: If No Jump: HERE Before Instruction PC After Instruction If Carry PC If Carry PC BNC Jump = address (HERE) = = = = 0; address (Jump) 1; address (HERE + 2) © 2008 Microchip Technology Inc. Example: HERE Before Instruction PC After Instruction If Negative PC If Negative PC BNN Jump = address (HERE) = = = = 0; address (Jump) 1; address (HERE + 2) DS39760D-page 223 PIC18F2450/4450 BNOV Branch if Not Overflow BNZ Branch if Not Zero Syntax: BNOV Syntax: BNZ n n Operands: -128 ≤ n ≤ 127 Operands: -128 ≤ n ≤ 127 Operation: if Overflow bit is ‘0’, (PC) + 2 + 2n → PC Operation: if Zero bit is ‘0’, (PC) + 2 + 2n → PC Status Affected: None Status Affected: None Encoding: 1110 0101 nnnn nnnn Encoding: 1110 0001 nnnn nnnn Description: If the Overflow bit is ‘0’, then the program will branch. The 2’s complement number ‘2n’ is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Description: If the Zero bit is ‘0’, then the program will branch. The 2’s complement number ‘2n’ is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Words: 1 Cycles: 1(2) Cycles: 1(2) Q Cycle Activity: If Jump: Q Cycle Activity: If Jump: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data Write to PC Decode Read literal ‘n’ Process Data Write to PC No operation No operation No operation No operation No operation No operation No operation No operation Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data No operation Decode Read literal ‘n’ Process Data No operation If No Jump: If No Jump: Example: HERE Before Instruction PC After Instruction If Overflow PC If Overflow PC DS39760D-page 224 BNOV Jump = address (HERE) = = = = 0; address (Jump) 1; address (HERE + 2) Example: HERE Before Instruction PC After Instruction If Zero PC If Zero PC BNZ Jump = address (HERE) = = = = 0; address (Jump) 1; address (HERE + 2) © 2008 Microchip Technology Inc. PIC18F2450/4450 BRA Unconditional Branch BSF Bit Set f Syntax: BRA Syntax: BSF Operands: -1024 ≤ n ≤ 1023 Operands: Operation: (PC) + 2 + 2n → PC Status Affected: None 0 ≤ f ≤ 255 0≤b≤7 a ∈ [0,1] Operation: 1 → f<b> Status Affected: None Encoding: n 1101 Description: 0nnn nnnn nnnn Add the 2’s complement number ‘2n’ to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is a two-cycle instruction. Words: 1 Cycles: 2 Encoding: 1000 Q1 Q2 Q3 Q4 Read literal ‘n’ Process Data Write to PC No operation No operation No operation No operation bbba ffff ffff Description: Bit ‘b’ in register ‘f’ is set. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Decode f, b {,a} Q Cycle Activity: Example: HERE Before Instruction PC After Instruction PC BRA Jump = address (HERE) = address (Jump) Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write register ‘f’ Example: BSF Before Instruction FLAG_REG After Instruction FLAG_REG © 2008 Microchip Technology Inc. FLAG_REG, 7, 1 = 0Ah = 8Ah DS39760D-page 225 PIC18F2450/4450 BTFSC Bit Test File, Skip if Clear BTFSS Bit Test File, Skip if Set Syntax: BTFSC f, b {,a} Syntax: BTFSS f, b {,a} Operands: 0 ≤ f ≤ 255 0≤b≤7 a ∈ [0,1] Operands: 0 ≤ f ≤ 255 0≤b<7 a ∈ [0,1] Operation: skip if (f<b>) = 0 Operation: skip if (f<b>) = 1 Status Affected: None Status Affected: None Encoding: 1011 Description: bbba ffff ffff Encoding: 1010 If bit ‘b’ in register ‘f’ is ‘0’, then the next instruction is skipped. If bit ‘b’ is ‘0’, then the next instruction fetched during the current instruction execution is discarded and a NOP is executed instead, making this a two-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Description: Words: 1 Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Cycles: 1(2) Note: Q Cycle Activity: bbba ffff ffff If bit ‘b’ in register ‘f’ is ‘1’, then the next instruction is skipped. If bit ‘b’ is ‘1’, then the next instruction fetched during the current instruction execution is discarded and a NOP is executed instead, making this a two-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data No operation Decode Read register ‘f’ Process Data No operation Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation If skip: If skip: If skip and followed by 2-word instruction: If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE FALSE TRUE Before Instruction PC After Instruction If FLAG<1> PC If FLAG<1> PC DS39760D-page 226 BTFSC : : FLAG, 1, 0 = address (HERE) = = = = 0; address (TRUE) 1; address (FALSE) Example: HERE FALSE TRUE Before Instruction PC After Instruction If FLAG<1> PC If FLAG<1> PC BTFSS : : FLAG, 1, 0 = address (HERE) = = = = 0; address (FALSE) 1; address (TRUE) © 2008 Microchip Technology Inc. PIC18F2450/4450 BTG Bit Toggle f BOV Branch if Overflow Syntax: BTG f, b {,a} Syntax: BOV Operands: 0 ≤ f ≤ 255 0≤b<7 a ∈ [0,1] Operands: -128 ≤ n ≤ 127 Operation: if Overflow bit is ‘1’, (PC) + 2 + 2n → PC Status Affected: None Operation: (f<b>) → f<b> Status Affected: None Encoding: 0111 Description: Encoding: bbba ffff ffff Bit ‘b’ in data memory location ‘f’ is inverted. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. n 1110 0100 nnnn nnnn Description: If the Overflow bit is ‘1’, then the program will branch. The 2’s complement number ‘2n’ is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Cycles: 1(2) Q Cycle Activity: If Jump: Words: 1 Q1 Q2 Q3 Q4 Cycles: 1 Decode Read literal ‘n’ Process Data Write to PC No operation No operation No operation No operation Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write register ‘f’ Example: BTG PORTC, 4, 0 Before Instruction: PORTC = 0111 0101 [75h] After Instruction: PORTC = 0110 0101 [65h] © 2008 Microchip Technology Inc. If No Jump: Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data No operation Example: HERE Before Instruction PC After Instruction If Overflow PC If Overflow PC BOV Jump = address (HERE) = = = = 1; address (Jump) 0; address (HERE + 2) DS39760D-page 227 PIC18F2450/4450 BZ Branch if Zero CALL Subroutine Call Syntax: BZ Syntax: CALL k {,s} n Operands: -128 ≤ n ≤ 127 Operands: Operation: if Zero bit is ‘1’, (PC) + 2 + 2n → PC 0 ≤ k ≤ 1048575 s ∈ [0,1] Operation: Status Affected: None (PC) + 4 → TOS, k → PC<20:1>; if s = 1, (W) → WS, (STATUS) → STATUSS, (BSR) → BSRS Status Affected: None Encoding: 1110 Description: 0000 nnnn nnnn If the Zero bit is ‘1’, then the program will branch. The 2’s complement number ‘2n’ is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Cycles: 1(2) Encoding: 1st word (k<7:0>) 2nd word(k<19:8>) Q1 Q2 Q3 Q4 Read literal ‘n’ Process Data Write to PC No operation No operation No operation No operation Q2 Q3 Q4 If No Jump: Q1 Decode Read literal ‘n’ Example: HERE Before Instruction PC After Instruction If Zero PC If Zero PC DS39760D-page 228 Process Data BZ No operation address (HERE) = = = = 1; address (Jump) 0; address (HERE + 2) kkkk0 kkkk8 Subroutine call of entire 2-Mbyte memory range. First, return address (PC + 4) is pushed onto the return stack. If ‘s’ = 1, the W, STATUS and BSR registers are also pushed into their respective shadow registers, WS, STATUSS and BSRS. If ‘s’ = 0, no update occurs (default). Then, the 20-bit value ‘k’ is loaded into PC<20:1>. CALL is a two-cycle instruction. Words: 2 Cycles: 2 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’<7:0>, Push PC to stack Read literal ‘k’<19:8>, Write to PC No operation No operation No operation No operation Jump = k7kkk kkkk 110s k19kkk Description: Q Cycle Activity: If Jump: Decode 1110 1111 Example: HERE Before Instruction PC = After Instruction PC = TOS = WS = BSRS = STATUSS = CALL THERE,1 address (HERE) address (THERE) address (HERE + 4) W BSR STATUS © 2008 Microchip Technology Inc. PIC18F2450/4450 CLRF Clear f Syntax: CLRF Operands: 0 ≤ f ≤ 255 a ∈ [0,1] f {,a} Operation: 000h → f, 1→Z Status Affected: Z Encoding: 0110 Description: 101a ffff ffff Clears the contents of the specified register. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write register ‘f’ CLRF Before Instruction FLAG_REG After Instruction FLAG_REG Clear Watchdog Timer Syntax: CLRWDT Operands: None Operation: 000h → WDT, 000h → WDT postscaler, 1 → TO, 1 → PD Status Affected: TO, PD Encoding: FLAG_REG,1 = 5Ah = 00h © 2008 Microchip Technology Inc. 0000 0000 0000 0100 Description: CLRWDT instruction resets the Watchdog Timer. It also resets the postscaler of the WDT. Status bits, TO and PD, are set. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation Process Data No operation Example: Q Cycle Activity: Example: CLRWDT CLRWDT Before Instruction WDT Counter After Instruction WDT Counter WDT Postscaler TO PD = ? = = = = 00h 0 1 1 DS39760D-page 229 PIC18F2450/4450 COMF Complement f CPFSEQ Compare f with W, Skip if f = W Syntax: COMF Syntax: CPFSEQ Operands: 0 ≤ f ≤ 255 a ∈ [0,1] Operation: (f) – (W), skip if (f) = (W) (unsigned comparison) Status Affected: None f {,d {,a}} Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (f) → dest Status Affected: N, Z Encoding: 0001 11da ffff ffff Description: The contents of register ‘f’ are complemented. If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: COMF Before Instruction REG = After Instruction REG = W = REG, 0, 0 Encoding: Description: 0110 001a ffff ffff Compares the contents of data memory location ‘f’ to the contents of W by performing an unsigned subtraction. If ‘f’ = W, then the fetched instruction is discarded and a NOP is executed instead, making this a two-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q1 Decode 13h Q2 Read register ‘f’ Q3 Process Data Q4 No operation If skip: 13h ECh Q1 Q2 Q3 No No No operation operation operation If skip and followed by 2-word instruction: Q1 Q2 Q3 No No No operation operation operation No No No operation operation operation Example: HERE NEQUAL EQUAL Before Instruction PC Address W REG After Instruction If REG PC If REG PC DS39760D-page 230 f {,a} Q4 No operation Q4 No operation No operation CPFSEQ REG, 0 : : = = = HERE ? ? = = ≠ = W; Address (EQUAL) W; Address (NEQUAL) © 2008 Microchip Technology Inc. PIC18F2450/4450 CPFSGT Compare f with W, Skip if f > W CPFSLT Compare f with W, Skip if f < W Syntax: CPFSGT Syntax: CPFSLT Operands: 0 ≤ f ≤ 255 a ∈ [0,1] Operands: 0 ≤ f ≤ 255 a ∈ [0,1] Operation: (f) – (W), skip if (f) > (W) (unsigned comparison) Operation: (f) – (W), skip if (f) < (W) (unsigned comparison) Status Affected: None Status Affected: None Encoding: Description: Words: Cycles: Q Cycle Activity: Q1 Decode 0110 f {,a} 010a ffff ffff Compares the contents of data memory location ‘f’ to the contents of the W by performing an unsigned subtraction. If the contents of ‘f’ are greater than the contents of WREG, then the fetched instruction is discarded and a NOP is executed instead, making this a two-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Encoding: Q2 Read register ‘f’ Q3 Process Data Q4 No operation Q1 Q2 Q3 No No No operation operation operation If skip and followed by 2-word instruction: Q1 Q2 Q3 No No No operation operation operation No No No operation operation operation Q4 No operation Example: HERE NGREATER GREATER Before Instruction PC W After Instruction If REG PC If REG PC CPFSGT REG, 0 : : = = Address (HERE) ? > = ≤ = W; Address (GREATER) W; Address (NGREATER) © 2008 Microchip Technology Inc. 000a ffff ffff Compares the contents of data memory location ‘f’ to the contents of W by performing an unsigned subtraction. If the contents of ‘f’ are less than the contents of W, then the fetched instruction is discarded and a NOP is executed instead, making this a two-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data No operation If skip: Q1 Q2 Q3 Q4 No operation No operation No operation No operation If skip and followed by 2-word instruction: If skip: Q4 No operation No operation 0110 Description: 1 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. f {,a} Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE NLESS LESS Before Instruction PC W After Instruction If REG PC If REG PC CPFSLT REG, 1 : : = = Address (HERE) ? < = ≥ = W; Address (LESS) W; Address (NLESS) DS39760D-page 231 PIC18F2450/4450 DAW Decimal Adjust W Register DECF Decrement f Syntax: DAW Syntax: DECF f {,d {,a}} Operands: None Operands: Operation: If [W<3:0> > 9] or [DC = 1] then, (W<3:0>) + 6 → W<3:0>; else, (W<3:0>) → W<3:0> 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (f) – 1 → dest Status Affected: C, DC, N, OV, Z If [W<7:4> + DC > 9] or [C = 1] then, (W<7:4>) + 6 + DC → W<7:4>; else, (W<7:4>) + DC → W<7:4> Status Affected: Encoding: 0000 0000 0000 0000 DAW adjusts the 8-bit value in W, resulting from the earlier addition of two variables (each in packed BCD format) and produces a correct packed BCD result. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register W Process Data Write W Example 1: DAW Before Instruction W = C = DC = After Instruction W = C = DC = A5h 0 0 05h 1 0 Example 2: Before Instruction W = C = DC = After Instruction W = C = DC = DS39760D-page 232 ffff Decrement register ‘f’. If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 0111 Description: ffff Description: C Encoding: 01da Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: DECF Before Instruction CNT = Z = After Instruction CNT = Z = CNT, 1, 0 01h 0 00h 1 CEh 0 0 34h 1 0 © 2008 Microchip Technology Inc. PIC18F2450/4450 DECFSZ Decrement f, Skip if 0 DCFSNZ Decrement f, Skip if Not 0 Syntax: DECFSZ f {,d {,a}} Syntax: DCFSNZ Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (f) – 1 → dest, skip if result = 0 Operation: (f) – 1 → dest, skip if result ≠ 0 Status Affected: None Status Affected: None Encoding: 0010 11da ffff ffff Description: The contents of register ‘f’ are decremented. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’ (default). If the result is ‘0’, the next instruction, which is already fetched, is discarded and a NOP is executed instead, making it a two-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Encoding: 0100 Description: 11da Q1 Q2 Q3 Q4 Read register ‘f’ Process Data Write to destination Q1 Q2 Q3 Q4 No operation No operation No operation No operation Words: 1 Cycles: 1(2) Note: Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation DECFSZ GOTO CNT, 1, 1 LOOP Example: HERE CONTINUE Before Instruction PC = After Instruction CNT = If CNT = PC = If CNT ≠ PC = Address (HERE) CNT – 1 0; Address (CONTINUE) 0; Address (HERE + 2) © 2008 Microchip Technology Inc. ffff 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination If skip: If skip and followed by 2-word instruction: ffff The contents of register ‘f’ are decremented. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’ (default). If the result is not ‘0’, the next instruction, which is already fetched, is discarded and a NOP is executed instead, making it a two-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Q Cycle Activity: Decode f {,d {,a}} If skip: Q1 Q2 Q3 Q4 No operation No operation No operation No operation If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE ZERO NZERO Before Instruction TEMP After Instruction TEMP If TEMP PC If TEMP PC DCFSNZ : : TEMP, 1, 0 = ? = = = ≠ = TEMP – 1, 0; Address (ZERO) 0; Address (NZERO) DS39760D-page 233 PIC18F2450/4450 GOTO Unconditional Branch INCF Increment f Syntax: GOTO k Syntax: INCF Operands: 0 ≤ k ≤ 1048575 Operands: Operation: k → PC<20:1> Status Affected: None 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (f) + 1 → dest Status Affected: C, DC, N, OV, Z Encoding: 1st word (k<7:0>) 2nd word(k<19:8>) 1110 1111 1111 k19kkk k7kkk kkkk kkkk0 kkkk8 Description: GOTO allows an unconditional branch anywhere within the entire 2-Mbyte memory range. The 20-bit value ‘k’ is loaded into PC<20:1>. GOTO is always a two-cycle instruction. Words: 2 Cycles: 2 Encoding: 0010 Q1 Q2 Q3 Q4 Read literal ‘k’<7:0>, No operation Read literal ‘k’<19:8>, Write to PC No operation No operation No operation No operation Example: GOTO THERE After Instruction PC = Address (THERE) ffff ffff The contents of register ‘f’ are incremented. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: INCF Before Instruction CNT = Z = C = DC = After Instruction CNT = Z = C = DC = DS39760D-page 234 10da Description: Q Cycle Activity: Decode f {,d {,a}} CNT, 1, 0 FFh 0 ? ? 00h 1 1 1 © 2008 Microchip Technology Inc. PIC18F2450/4450 INCFSZ Increment f, Skip if 0 INFSNZ Syntax: INCFSZ Syntax: INFSNZ 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] f {,d {,a}} Increment f, Skip if Not 0 f {,d {,a}} Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operands: Operation: (f) + 1 → dest, skip if result = 0 Operation: (f) + 1 → dest, skip if result ≠ 0 Status Affected: None Status Affected: None Encoding: 0011 11da ffff ffff Encoding: 0100 Description: ffff ffff The contents of register ‘f’ are incremented. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’ (default). If the result is not ‘0’, the next instruction, which is already fetched, is discarded and a NOP is executed instead, making it a two-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Description: The contents of register ‘f’ are incremented. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’. (default) If the result is ‘0’, the next instruction, which is already fetched, is discarded and a NOP is executed instead, making it a two-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Cycles: 1(2) Note: Q Cycle Activity: 10da 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Decode Read register ‘f’ Process Data Write to destination Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation If skip: If skip: If skip and followed by 2-word instruction: If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE NZERO ZERO Before Instruction PC = After Instruction CNT = If CNT = PC = If CNT ≠ PC = INCFSZ : : Address (HERE) CNT + 1 0; Address (ZERO) 0; Address (NZERO) © 2008 Microchip Technology Inc. CNT, 1, 0 Example: HERE ZERO NZERO Before Instruction PC = After Instruction REG = If REG ≠ PC = If REG = PC = INFSNZ REG, 1, 0 Address (HERE) REG + 1 0; Address (NZERO) 0; Address (ZERO) DS39760D-page 235 PIC18F2450/4450 IORLW Inclusive OR Literal with W IORWF Inclusive OR W with f Syntax: IORLW k Syntax: IORWF Operands: 0 ≤ k ≤ 255 Operands: Operation: (W) .OR. k → W Status Affected: N, Z 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (W) .OR. (f) → dest Status Affected: N, Z Encoding: 0000 1001 kkkk kkkk Description: The contents of W are ORed with the 8-bit literal ‘k’. The result is placed in W. Words: 1 Cycles: 1 Encoding: 0001 Q1 Q2 Q3 Q4 Read literal ‘k’ Process Data Write to W Example: IORLW Before Instruction W = After Instruction W = 00da ffff ffff Description: Inclusive OR W with register ‘f’. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Decode f {,d {,a}} 35h 9Ah BFh Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: IORWF Before Instruction RESULT = W = After Instruction RESULT = W = DS39760D-page 236 RESULT, 0, 1 13h 91h 13h 93h © 2008 Microchip Technology Inc. PIC18F2450/4450 LFSR Load FSR MOVF Move f Syntax: LFSR f, k Syntax: MOVF Operands: 0≤f≤2 0 ≤ k ≤ 4095 Operands: Operation: k → FSRf 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Status Affected: None Operation: f → dest Status Affected: N, Z Encoding: 1110 1111 1110 0000 00ff k7kkk k11kkk kkkk Description: The 12-bit literal ‘k’ is loaded into the File Select Register pointed to by ‘f’. Words: 2 Cycles: 2 Encoding: 0101 Q1 Q2 Q3 Q4 Read literal ‘k’ MSB Process Data Write literal ‘k’ MSB to FSRfH Decode Read literal ‘k’ LSB Process Data Write literal ‘k’ to FSRfL Example: After Instruction FSR2H FSR2L 03h ABh ffff ffff The contents of register ‘f’ are moved to a destination dependent upon the status of ‘d’. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’ (default). Location ‘f’ can be anywhere in the 256-byte bank. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 LFSR 2, 3ABh = = 00da Description: Q Cycle Activity: Decode f {,d {,a}} Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write W Example: MOVF Before Instruction REG W After Instruction REG W © 2008 Microchip Technology Inc. REG, 0, 0 = = 22h FFh = = 22h 22h DS39760D-page 237 PIC18F2450/4450 MOVFF Move f to f MOVLB Move Literal to Low Nibble in BSR Syntax: MOVFF fs,fd Syntax: MOVLW k Operands: 0 ≤ fs ≤ 4095 0 ≤ fd ≤ 4095 Operands: 0 ≤ k ≤ 255 Operation: k → BSR Status Affected: None Operation: (fs) → fd Status Affected: None Encoding: 1st word (source) 2nd word (destin.) Encoding: 1100 1111 Description: ffff ffff ffff ffff ffffs ffffd The contents of source register ‘fs’ are moved to destination register ‘fd’. Location of source ‘fs’ can be anywhere in the 4096-byte data space (000h to FFFh) and location of destination ‘fd’ can also be anywhere from 000h to FFFh. Either source or destination can be W (a useful special situation). MOVFF is particularly useful for transferring a data memory location to a peripheral register (such as the transmit buffer or an I/O port). The MOVFF instruction cannot use the PCL, TOSU, TOSH or TOSL as the destination register. Words: 2 Cycles: 2 0000 0001 kkkk kkkk Description: The 8-bit literal ‘k’ is loaded into the Bank Select Register (BSR). The value of BSR<7:4> always remains ‘0’ regardless of the value of k7:k4. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write literal ‘k’ to BSR MOVLB 5 Example: Before Instruction BSR Register = After Instruction BSR Register = 02h 05h Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ (src) Process Data No operation Decode No operation No operation Write register ‘f’ (dest) No dummy read Example: MOVFF Before Instruction REG1 REG2 After Instruction REG1 REG2 DS39760D-page 238 REG1, REG2 = = 33h 11h = = 33h 33h © 2008 Microchip Technology Inc. PIC18F2450/4450 MOVLW Move Literal to W MOVWF Move W to f Syntax: MOVLW k Syntax: MOVWF Operands: 0 ≤ k ≤ 255 Operands: Operation: k→W 0 ≤ f ≤ 255 a ∈ [0,1] Status Affected: None Encoding: 0000 Description: 1110 kkkk kkkk The 8-bit literal ‘k’ is loaded into W. Words: 1 Cycles: 1 Operation: (W) → f Status Affected: None Encoding: 0110 Q1 Q2 Q3 Q4 Read literal ‘k’ Process Data Write to W Example: After Instruction W = MOVLW 111a ffff ffff Description: Move data from W to register ‘f’. Location ‘f’ can be anywhere in the 256-byte bank. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Decode f {,a} 5Ah 5Ah Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write register ‘f’ Example: MOVWF Before Instruction W = REG = After Instruction W = REG = © 2008 Microchip Technology Inc. REG, 0 4Fh FFh 4Fh 4Fh DS39760D-page 239 PIC18F2450/4450 MULLW Multiply Literal with W MULWF Multiply W with f Syntax: MULLW Syntax: MULWF Operands: 0 ≤ f ≤ 255 a ∈ [0,1] Operation: (W) x (f) → PRODH:PRODL Status Affected: None k Operands: 0 ≤ k ≤ 255 Operation: (W) x k → PRODH:PRODL Status Affected: None Encoding: 0000 Description: 1101 kkkk kkkk An unsigned multiplication is carried out between the contents of W and the 8-bit literal ‘k’. The 16-bit result is placed in PRODH:PRODL register pair. PRODH contains the high byte. W is unchanged. None of the Status flags are affected. Note that neither Overflow nor Carry is possible in this operation. A zero result is possible but not detected. Words: 1 Cycles: 1 Encoding: 0000 Q1 Q2 Q3 Q4 Read literal ‘k’ Process Data Write registers PRODH: PRODL Example: Before Instruction W PRODH PRODL After Instruction W PRODH PRODL MULLW = = = ffff Words: 1 Cycles: 1 Q Cycle Activity: = = = E2h ADh 08h Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write registers PRODH: PRODL Example: Before Instruction W REG PRODH PRODL After Instruction W REG PRODH PRODL DS39760D-page 240 ffff An unsigned multiplication is carried out between the contents of W and the register file location ‘f’. The 16-bit result is stored in the PRODH:PRODL register pair. PRODH contains the high byte. Both W and ‘f’ are unchanged. None of the Status flags are affected. Note that neither Overflow nor Carry is possible in this operation. A zero result is possible but not detected. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. 0C4h E2h ? ? 001a Description: Q Cycle Activity: Decode f {,a} MULWF REG, 1 = = = = C4h B5h ? ? = = = = C4h B5h 8Ah 94h © 2008 Microchip Technology Inc. PIC18F2450/4450 NEGF Negate f Syntax: NEGF Operands: 0 ≤ f ≤ 255 a ∈ [0,1] f {,a} Operation: (f) + 1 → f Status Affected: N, OV, C, DC, Z Encoding: 0110 Description: 1 Cycles: 1 No Operation Syntax: NOP Operands: None Operation: No operation Status Affected: None Encoding: 110a ffff 0000 1111 ffff Location ‘f’ is negated using two’s complement. The result is placed in the data memory location ‘f’. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: NOP 0000 xxxx Description: No operation. Words: 1 Cycles: 1 0000 xxxx 0000 xxxx Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation No operation No operation Example: None. Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write register ‘f’ Example: NEGF Before Instruction REG = After Instruction REG = REG, 1 0011 1010 [3Ah] 1100 0110 [C6h] © 2008 Microchip Technology Inc. DS39760D-page 241 PIC18F2450/4450 POP Pop Top of Return Stack PUSH Push Top of Return Stack Syntax: POP Syntax: PUSH Operands: None Operands: None Operation: (TOS) → bit bucket Operation: (PC + 2) → TOS Status Affected: None Status Affected: None Encoding: 0000 0000 0000 0110 Encoding: 0000 0000 0000 0101 Description: The TOS value is pulled off the return stack and is discarded. The TOS value then becomes the previous value that was pushed onto the return stack. This instruction is provided to enable the user to properly manage the return stack to incorporate a software stack. Description: The PC + 2 is pushed onto the top of the return stack. The previous TOS value is pushed down on the stack. This instruction allows implementing a software stack by modifying TOS and then pushing it onto the return stack. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Q Cycle Activity: Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation Pop TOS value No operation POP GOTO NEW Example: Q2 Q3 Q4 Push PC + 2 onto return stack No operation No operation Example: Before Instruction TOS Stack (1 level down) = = 0031A2h 014332h After Instruction TOS PC = = 014332h NEW DS39760D-page 242 Q1 Decode PUSH Before Instruction TOS PC = = 345Ah 0124h After Instruction PC TOS Stack (1 level down) = = = 0126h 0126h 345Ah © 2008 Microchip Technology Inc. PIC18F2450/4450 RCALL Relative Call RESET Reset Syntax: RCALL Syntax: RESET n Operands: -1024 ≤ n ≤ 1023 Operands: None Operation: (PC) + 2 → TOS, (PC) + 2 + 2n → PC Operation: Reset all registers and flags that are affected by a MCLR Reset. Status Affected: None Status Affected: All Encoding: 1101 Description: 1nnn nnnn nnnn Subroutine call with a jump up to 1K from the current location. First, return address (PC + 2) is pushed onto the stack. Then, add the 2’s complement number ‘2n’ to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is a two-cycle instruction. Words: 1 Cycles: 2 Encoding: 0000 Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data Write to PC No operation No operation 1111 1111 This instruction provides a way to execute a MCLR Reset in software. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Start Reset No operation No operation Example: Q Cycle Activity: 0000 Description: After Instruction Registers = Flags* = RESET Reset Value Reset Value Push PC to stack No operation Example: No operation HERE RCALL Jump Before Instruction PC = Address (HERE) After Instruction PC = Address (Jump) TOS = Address (HERE + 2) © 2008 Microchip Technology Inc. DS39760D-page 243 PIC18F2450/4450 RETFIE Return from Interrupt RETLW Return Literal to W Syntax: RETFIE {s} Syntax: RETLW k Operands: s ∈ [0,1] Operands: 0 ≤ k ≤ 255 Operation: (TOS) → PC, 1 → GIE/GIEH or PEIE/GIEL; if s = 1, (WS) → W, (STATUSS) → STATUS, (BSRS) → BSR, PCLATU, PCLATH are unchanged Operation: k → W, (TOS) → PC, PCLATU, PCLATH are unchanged Status Affected: None Status Affected: 0000 0000 Description: 0000 0001 Words: 1 Cycles: 2 Q Cycle Activity: kkkk kkkk W is loaded with the 8-bit literal ‘k’. The program counter is loaded from the top of the stack (the return address). The high address latch (PCLATH) remains unchanged. Words: 1 Cycles: 2 000s Return from interrupt. Stack is popped and Top-of-Stack (TOS) is loaded into the PC. Interrupts are enabled by setting either the high or low-priority global interrupt enable bit. If ‘s’ = 1, the contents of the shadow registers WS, STATUSS and BSRS are loaded into their corresponding registers, W, STATUS and BSR. If ‘s’ = 0, no update of these registers occurs (default). 1100 Description: GIE/GIEH, PEIE/GIEL. Encoding: Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Pop PC from stack, Write to W No operation No operation No operation No operation Example: Q1 Q2 Q3 Q4 Decode No operation No operation Pop PC from stack Set GIEH or GIEL No operation Encoding: No operation Example: RETFIE After Interrupt PC W BSR STATUS GIE/GIEH, PEIE/GIEL DS39760D-page 244 No operation No operation 1 = = = = = TOS WS BSRS STATUSS 1 CALL TABLE ; ; ; ; : TABLE ADDWF PCL ; RETLW k0 ; RETLW k1 ; : : RETLW kn ; Before Instruction W = After Instruction W = W contains table offset value W now has table value W = offset Begin table End of table 07h value of kn © 2008 Microchip Technology Inc. PIC18F2450/4450 RETURN Return from Subroutine RLCF Rotate Left f through Carry Syntax: RETURN {s} Syntax: RLCF Operands: s ∈ [0,1] Operands: Operation: (TOS) → PC; if s = 1, (WS) → W, (STATUSS) → STATUS, (BSRS) → BSR, PCLATU, PCLATH are unchanged 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (f<n>) → dest<n + 1>, (f<7>) → C, (C) → dest<0> Status Affected: C, N, Z Status Affected: None Encoding: 0000 Encoding: 0000 0001 001s Description: Return from subroutine. The stack is popped and the top of the stack (TOS) is loaded into the program counter. If ‘s’= 1, the contents of the shadow registers WS, STATUSS and BSRS are loaded into their corresponding registers, W, STATUS and BSR. If ‘s’ = 0, no update of these registers occurs (default). Words: 1 Cycles: 2 0011 Description: Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation Process Data Pop PC from stack No operation No operation No operation No operation f {,d {,a}} 01da ffff ffff The contents of register ‘f’ are rotated one bit to the left through the Carry flag. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. register f C Words: 1 Cycles: 1 Q Cycle Activity: Example: RETURN After Instruction: PC = TOS Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: Before Instruction REG = C = After Instruction REG = W = C = © 2008 Microchip Technology Inc. RLCF REG, 0, 0 1110 0110 0 1110 0110 1100 1100 1 DS39760D-page 245 PIC18F2450/4450 RLNCF Rotate Left f (No Carry) RRCF Rotate Right f through Carry Syntax: RLNCF Syntax: RRCF Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (f<n>) → dest<n + 1>, (f<7>) → dest<0> Operation: Status Affected: N, Z (f<n>) → dest<n – 1>, (f<0>) → C, (C) → dest<7> Status Affected: C, N, Z Encoding: 0100 Description: f {,d {,a}} 01da ffff ffff The contents of register ‘f’ are rotated one bit to the left. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Encoding: 0011 Description: register f Words: 1 Cycles: 1 Decode Q2 Read register ‘f’ Example: Before Instruction REG = After Instruction REG = DS39760D-page 246 00da RLNCF Q3 Process Data Q4 Write to destination Words: 1 Cycles: 0101 0111 ffff register f 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination REG, 1, 0 1010 1011 ffff The contents of register ‘f’ are rotated one bit to the right through the Carry flag. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. C Q Cycle Activity: Q1 f {,d {,a}} Example: RRCF Before Instruction REG = C = After Instruction REG = W = C = REG, 0, 0 1110 0110 0 1110 0110 0111 0011 0 © 2008 Microchip Technology Inc. PIC18F2450/4450 RRNCF Rotate Right f (No Carry) SETF Set f Syntax: RRNCF Syntax: SETF Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operands: 0 ≤ f ≤ 255 a ∈ [0,1] Operation: (f<n>) → dest<n – 1>, (f<0>) → dest<7> Status Affected: N, Z Encoding: 0100 Description: f {,d {,a}} 00da ffff ffff register f 1 Cycles: 1 Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination RRNCF Before Instruction REG = After Instruction REG = Example 2: 0110 100a ffff ffff Description: The contents of the specified register are set to FFh. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write register ‘f’ SETF Before Instruction REG After Instruction REG REG,1 = 5Ah = FFh REG, 1, 0 1101 0111 1110 1011 RRNCF Before Instruction W = REG = After Instruction W = REG = None Example: Q Cycle Activity: Example 1: FFh → f Status Affected: Encoding: The contents of register ‘f’ are rotated one bit to the right. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank will be selected, overriding the BSR value. If ‘a’ is ‘1’, then the bank will be selected as per the BSR value (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: Operation: f {,a} REG, 0, 0 ? 1101 0111 1110 1011 1101 0111 © 2008 Microchip Technology Inc. DS39760D-page 247 PIC18F2450/4450 SLEEP Enter Sleep Mode SUBFWB Subtract f from W with Borrow Syntax: SLEEP Syntax: SUBFWB Operands: None Operands: Operation: 00h → WDT, 0 → WDT postscaler, 1 → TO, 0 → PD 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (W) – (f) – (C) → dest Status Affected: N, OV, C, DC, Z Status Affected: TO, PD Encoding: 0000 Encoding: 0000 0000 0011 Description: The Power-Down status bit (PD) is cleared. The Time-out status bit (TO) is set. Watchdog Timer and its postscaler are cleared. The processor is put into Sleep mode with the oscillator stopped. Words: 1 Cycles: 1 0101 Q1 Q2 Q3 Q4 No operation Process Data Go to Sleep Example: SLEEP Before Instruction TO = ? ? PD = After Instruction TO = 1† 0 PD = † If WDT causes wake-up, this bit is cleared. DS39760D-page 248 01da ffff ffff Description: Subtract register ‘f’ and Carry flag (borrow) from W (2’s complement method). If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Decode f {,d {,a}} Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination SUBFWB REG, 1, 0 Example 1: Before Instruction REG = 3 W = 2 C = 1 After Instruction REG = FF W = 2 C = 0 Z = 0 N = 1 ; result is negative SUBFWB REG, 0, 0 Example 2: Before Instruction REG = 2 W = 5 C = 1 After Instruction REG = 2 W = 3 C = 1 Z = 0 N = 0 ; result is positive SUBFWB REG, 1, 0 Example 3: Before Instruction REG = 1 W = 2 C = 0 After Instruction REG = 0 W = 2 C = 1 Z = 1 ; result is zero N = 0 © 2008 Microchip Technology Inc. PIC18F2450/4450 SUBLW Subtract W from Literal SUBWF Subtract W from f Syntax: SUBLW k Syntax: SUBWF Operands: 0 ≤ k ≤ 255 Operands: Operation: k – (W) → W Status Affected: N, OV, C, DC, Z 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (f) – (W) → dest Status Affected: N, OV, C, DC, Z Encoding: 0000 1000 kkkk kkkk Description W is subtracted from the 8-bit literal ‘k’. The result is placed in W. Words: 1 Cycles: 1 Encoding: 0101 Q1 Q2 Q3 Q4 Read literal ‘k’ Process Data Write to W Example 1: Before Instruction W = C = After Instruction W = C = Z = N = Example 2: Before Instruction W = C = After Instruction W = C = Z = N = Example 3: Before Instruction W = C = After Instruction W = C = Z = N = SUBLW SUBLW 1 Cycles: 1 ; result is positive 02h ? 00h 1 1 0 SUBLW Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination SUBWF REG, 1, 0 ; result is zero Example 1: 02h 03h ? FFh 0 0 1 ffff Words: 02h 02h ffff Subtract W from register ‘f’ (2’s complement method). If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. 01h ? 01h 1 0 0 11da Description: Q Cycle Activity: Decode f {,d {,a}} ; (2’s complement) ; result is negative Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 2: Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 3: Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = © 2008 Microchip Technology Inc. 3 2 ? 1 2 1 0 0 SUBWF ; result is positive REG, 0, 0 2 2 ? 2 0 1 1 0 SUBWF ; result is zero REG, 1, 0 1 2 ? FFh ;(2’s complement) 2 0 ; result is negative 0 1 DS39760D-page 249 PIC18F2450/4450 SUBWFB Subtract W from f with Borrow SWAPF Swap f Syntax: SUBWFB Syntax: SWAPF f {,d {,a}} Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (f) – (W) – (C) → dest Operation: Status Affected: N, OV, C, DC, Z (f<3:0>) → dest<7:4>, (f<7:4>) → dest<3:0> Status Affected: None Encoding: 0101 Description: 1 Cycles: 1 Q2 Read register ‘f’ Example 1: SUBWFB Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 2: ffff ffff Q3 Process Data Q4 Write to destination Encoding: (0001 1001) (0000 1101) 0Ch 0Dh 1 0 0 (0000 1011) (0000 1101) 10da ffff ffff The upper and lower nibbles of register ‘f’ are exchanged. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination REG, 1, 0 19h 0Dh 1 0011 Description: Example: SWAPF Before Instruction REG = After Instruction REG = REG, 1, 0 53h 35h ; result is positive SUBWFB REG, 0, 0 Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 3: 1Bh 1Ah 0 (0001 1011) (0001 1010) 1Bh 00h 1 1 0 (0001 1011) SUBWFB Before Instruction REG = W = C = After Instruction REG = W C Z N 10da Subtract W and the Carry flag (borrow) from register ‘f’ (2’s complement method). If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: Q Cycle Activity: Q1 Decode f {,d {,a}} = = = = DS39760D-page 250 ; result is zero REG, 1, 0 03h 0Eh 1 (0000 0011) (0000 1101) F5h (1111 0100) ; [2’s comp] (0000 1101) 0Eh 0 0 1 ; result is negative © 2008 Microchip Technology Inc. PIC18F2450/4450 TBLRD Table Read TBLRD Table Read (Continued) Syntax: TBLRD ( *; *+; *-; +*) Example 1: TBLRD Operands: None Operation: if TBLRD *, (Prog Mem (TBLPTR)) → TABLAT, TBLPTR – No Change; if TBLRD *+, (Prog Mem (TBLPTR)) → TABLAT, (TBLPTR) + 1 → TBLPTR; if TBLRD *-, (Prog Mem (TBLPTR)) → TABLAT, (TBLPTR) – 1 → TBLPTR; if TBLRD +*, (TBLPTR) + 1 → TBLPTR, (Prog Mem (TBLPTR)) → TABLAT Before Instruction TABLAT TBLPTR MEMORY (00A356h) After Instruction TABLAT TBLPTR Example 2: Status Affected: None Encoding: 0000 0000 0000 *+ ; 10nn nn=0 * =1 *+ =2 *=3 +* Description: This instruction is used to read the contents of Program Memory (P.M.). To address the program memory, a pointer called Table Pointer (TBLPTR) is used. The TBLPTR (a 21-bit pointer) points to each byte in the program memory. TBLPTR has a 2-Mbyte address range. TBLPTR<0> = 0: Least Significant Byte of Program Memory Word TBLPTR<0> = 1: Most Significant Byte of Program Memory Word The TBLRD instruction can modify the value of TBLPTR as follows: • no change • post-increment • post-decrement • pre-increment Words: 1 Cycles: 2 TBLRD = = = 55h 00A356h 34h = = 34h 00A357h +* ; Before Instruction TABLAT TBLPTR MEMORY (01A357h) MEMORY (01A358h) After Instruction TABLAT TBLPTR = = = = AAh 01A357h 12h 34h = = 34h 01A358h Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation No operation No operation No operation No operation (Read Program Memory) No operation No operation (Write TABLAT) © 2008 Microchip Technology Inc. DS39760D-page 251 PIC18F2450/4450 TBLWT Table Write TBLWT Table Write (Continued) Syntax: TBLWT ( *; *+; *-; +*) Example 1: TBLWT Operands: None Operation: if TBLWT*, (TABLAT) → Holding Register, TBLPTR – No Change; if TBLWT*+, (TABLAT) → Holding Register, (TBLPTR) + 1 → TBLPTR; if TBLWT*-, (TABLAT) → Holding Register, (TBLPTR) – 1 → TBLPTR; if TBLWT+*, (TBLPTR) + 1 → TBLPTR, (TABLAT) → Holding Register Before Instruction TABLAT = 55h TBLPTR = 00A356h HOLDING REGISTER (00A356h) = FFh After Instructions (table write completion) TABLAT = 55h TBLPTR = 00A357h HOLDING REGISTER (00A356h) = 55h Example 2: Status Affected: None Encoding: 0000 0000 0000 *+; 11nn nn=0 * =1 *+ =2 *=3 +* Description: This instruction uses the 3 LSBs of TBLPTR to determine which of the 8 holding registers the TABLAT is written to. The holding registers are used to program the contents of Program Memory (P.M.). (Refer to Section 6.0 “Flash Program Memory” for additional details on programming Flash memory.) The TBLPTR (a 21-bit pointer) points to each byte in the program memory. TBLPTR has a 2-Mbyte address range. The LSb of the TBLPTR selects which byte of the program memory location to access. TBLPTR<0> = 0: Least Significant Byte of Program Memory Word TBLPTR<0> = 1: Most Significant Byte of Program Memory Word The TBLWT instruction can modify the value of TBLPTR as follows: • no change • post-increment • post-decrement • pre-increment Words: 1 Cycles: 2 TBLWT +*; Before Instruction TABLAT = 34h TBLPTR = 01389Ah HOLDING REGISTER (01389Ah) = FFh HOLDING REGISTER (01389Bh) = FFh After Instruction (table write completion) TABLAT = 34h TBLPTR = 01389Bh HOLDING REGISTER (01389Ah) = FFh HOLDING REGISTER (01389Bh) = 34h Q Cycle Activity: Q1 Decode Q2 Q3 Q4 No No No operation operation operation No No No No operation operation operation operation (Read (Write to TABLAT) Holding Register) DS39760D-page 252 © 2008 Microchip Technology Inc. PIC18F2450/4450 TSTFSZ Test f, Skip if 0 Syntax: TSTFSZ f {,a} Operands: 0 ≤ f ≤ 255 a ∈ [0,1] Operation: skip if f = 0 Status Affected: None Encoding: 0110 Description: 011a ffff ffff If ‘f’ = 0, the next instruction fetched during the current instruction execution is discarded and a NOP is executed, making this a two-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. XORLW Exclusive OR Literal with W Syntax: XORLW k Operands: 0 ≤ k ≤ 255 Operation: (W) .XOR. k → W Status Affected: N, Z Encoding: 0000 1010 kkkk kkkk Description: The contents of W are XORed with the 8-bit literal ‘k’. The result is placed in W. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write to W Example: Before Instruction W = After Instruction W = XORLW 0AFh B5h 1Ah Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data No operation If skip: Q1 Q2 Q3 Q4 No operation No operation No operation No operation If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE NZERO ZERO Before Instruction PC After Instruction If CNT PC If CNT PC TSTFSZ : : CNT, 1 = Address (HERE) = = ≠ = 00h, Address (ZERO) 00h, Address (NZERO) © 2008 Microchip Technology Inc. DS39760D-page 253 PIC18F2450/4450 XORWF Exclusive OR W with f Syntax: XORWF Operands: 0 ≤ f ≤ 255 d ∈ [0,1] a ∈ [0,1] Operation: (W) .XOR. (f) → dest Status Affected: N, Z Encoding: 0001 f {,d {,a}} 10da ffff ffff Description: Exclusive OR the contents of W with register ‘f’. If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in the register ‘f’ (default). If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank (default). If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f ≤ 95 (5Fh). See Section 19.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: XORWF Before Instruction REG = W = After Instruction REG = W = DS39760D-page 254 REG, 1, 0 AFh B5h 1Ah B5h © 2008 Microchip Technology Inc. PIC18F2450/4450 19.2 Extended Instruction Set A summary of the instructions in the extended instruction set is provided in Table 19-3. Detailed descriptions are provided in Section 19.2.2 “Extended Instruction Set”. The opcode field descriptions in Table 19-1 (page 214) apply to both the standard and extended PIC18 instruction sets. In addition to the standard 75 instructions of the PIC18 instruction set, PIC18F2450/4450 devices also provide an optional extension to the core CPU functionality. The added features include eight additional instructions that augment indirect and indexed addressing operations and the implementation of Indexed Literal Offset Addressing mode for many of the standard PIC18 instructions. Note: The additional features of the extended instruction set are disabled by default. To enable them, users must set the XINST Configuration bit. The instructions in the extended set can all be classified as literal operations, which either manipulate the File Select Registers, or use them for Indexed Addressing. Two of the instructions, ADDFSR and SUBFSR, each have an additional special instantiation for using FSR2. These versions (ADDULNK and SUBULNK) allow for automatic return after execution. 19.2.1 EXTENDED INSTRUCTION SYNTAX Most of the extended instructions use indexed arguments, using one of the File Select Registers and some offset to specify a source or destination register. When an argument for an instruction serves as part of Indexed Addressing, it is enclosed in square brackets (“[ ]”). This is done to indicate that the argument is used as an index or offset. The MPASM™ Assembler will flag an error if it determines that an index or offset value is not bracketed. The extended instructions are specifically implemented to optimize re-entrant program code (that is, code that is recursive or that uses a software stack) written in high-level languages, particularly C. Among other things, they allow users working in high-level languages to perform certain operations on data structures more efficiently. These include: When the extended instruction set is enabled, brackets are also used to indicate index arguments in byteoriented and bit-oriented instructions. This is in addition to other changes in their syntax. For more details, see Section 19.2.3.1 “Extended Instruction Syntax with Standard PIC18 Commands”. • Dynamic allocation and deallocation of software stack space when entering and leaving subroutines • Function Pointer invocation • Software Stack Pointer manipulation • Manipulation of variables located in a software stack TABLE 19-3: The instruction set extension and the Indexed Literal Offset Addressing mode were designed for optimizing applications written in C; the user may likely never use these instructions directly in assembler. The syntax for these commands is provided as a reference for users who may be reviewing code that has been generated by a compiler. Note: In the past, square brackets have been used to denote optional arguments in the PIC18 and earlier instruction sets. In this text and going forward, optional arguments are denoted by braces (“{ }”). EXTENSIONS TO THE PIC18 INSTRUCTION SET Mnemonic, Operands ADDFSR ADDULNK CALLW MOVSF f, k k MOVSS zs, zd PUSHL k SUBFSR SUBULNK f, k k zs, fd Description Add Literal to FSR Add Literal to FSR2 and Return Call Subroutine using WREG Move zs (source) to 1st word fd (destination) 2nd word Move zs (source) to 1st word zd (destination) 2nd word Store Literal at FSR2, Decrement FSR2 Subtract Literal from FSR Subtract Literal from FSR2 and Return © 2008 Microchip Technology Inc. Cycles 1 2 2 2 16-Bit Instruction Word MSb LSb Status Affected 1000 1000 0000 1011 ffff 1011 xxxx 1010 ffkk 11kk 0001 0zzz ffff 1zzz xzzz kkkk kkkk kkkk 0100 zzzz ffff zzzz zzzz kkkk None None None None 1 1110 1110 0000 1110 1111 1110 1111 1110 1 2 1110 1110 1001 1001 ffkk 11kk kkkk kkkk None None 2 None None DS39760D-page 255 PIC18F2450/4450 19.2.2 EXTENDED INSTRUCTION SET ADDFSR Add Literal to FSR ADDULNK Syntax: ADDFSR f, k Syntax: ADDULNK k Operands: 0 ≤ k ≤ 63 f ∈ [ 0, 1, 2 ] Operands: 0 ≤ k ≤ 63 Operation: FSR(f) + k → FSR(f) Status Affected: None Encoding: 1110 Add Literal to FSR2 and Return FSR2 + k → FSR2, Operation: (TOS) → PC Status Affected: 1000 ffkk kkkk Description: The 6-bit literal ‘k’ is added to the contents of the FSR specified by ‘f’. Words: 1 Cycles: 1 None Encoding: 1110 Q1 Q2 Q3 Q4 Read literal ‘k’ Process Data Write to FSR Example: ADDFSR Before Instruction FSR2 = 03FFh After Instruction FSR2 = 0422h 2, 23h kkkk Words: 1 Cycles: 2 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write to FSR No Operation No Operation No Operation No Operation Example: Note: 11kk The 6-bit literal ‘k’ is added to the contents of FSR2. A RETURN is then executed by loading the PC with the TOS. The instruction takes two cycles to execute; a NOP is performed during the second cycle. This may be thought of as a special case of the ADDFSR instruction, where f = 3 (binary ‘11’); it operates only on FSR2. Q Cycle Activity: Decode 1000 Description: ADDULNK 23h Before Instruction FSR2 = PC = 03FFh 0100h After Instruction FSR2 = PC = 0422h (TOS) All PIC18 instructions may take an optional label argument preceding the instruction mnemonic for use in symbolic addressing. If a label is used, the instruction syntax then becomes: {label} instruction argument(s). DS39760D-page 256 © 2008 Microchip Technology Inc. PIC18F2450/4450 CALLW Subroutine Call Using WREG MOVSF Move Indexed to f Syntax: CALLW Syntax: MOVSF [zs], fd Operands: None Operands: Operation: (PC + 2) → TOS, (W) → PCL, (PCLATH) → PCH, (PCLATU) → PCU 0 ≤ zs ≤ 127 0 ≤ fd ≤ 4095 Operation: ((FSR2) + zs) → fd Status Affected: None Status Affected: None Encoding: 0000 0000 0001 0100 Description First, the return address (PC + 2) is pushed onto the return stack. Next, the contents of W are written to PCL; the existing value is discarded. Then the contents of PCLATH and PCLATU are latched into PCH and PCU, respectively. The second cycle is executed as a NOP instruction while the new next instruction is fetched. Unlike CALL, there is no option to update W, STATUS or BSR. Words: 1 Cycles: 2 Encoding: 1st word (source) 2nd word (destin.) Q1 Q2 Q3 Q4 Read WREG Push PC to stack No operation No operation No operation No operation No operation HERE Before Instruction PC = PCLATH = PCLATU = W = After Instruction PC = TOS = PCLATH = PCLATU = W = 2 Cycles: 2 Q Cycle Activity: Q1 Decode address (HERE) 10h 00h 06h © 2008 Microchip Technology Inc. zzzzs ffffd Words: CALLW 001006h address (HERE + 2) 10h 00h 06h 0zzz ffff The contents of the source register are moved to destination register ‘fd’. The actual address of the source register is determined by adding the 7-bit literal offset ‘zs’ in the first word to the value of FSR2. The address of the destination register is specified by the 12-bit literal ‘fd’ in the second word. Both addresses can be anywhere in the 4096-byte data space (000h to FFFh). The MOVSF instruction cannot use the PCL, TOSU, TOSH or TOSL as the destination register. If the resultant source address points to an indirect addressing register, the value returned will be 00h. Decode Example: 1011 ffff Description: Q Cycle Activity: Decode 1110 1111 Q2 Q3 Determine Determine source addr source addr No operation No operation No dummy read Example: MOVSF Before Instruction FSR2 Contents of 85h REG2 After Instruction FSR2 Contents of 85h REG2 Q4 Read source reg Write register ‘f’ (dest) [05h], REG2 = 80h = = 33h 11h = 80h = = 33h 33h DS39760D-page 257 PIC18F2450/4450 MOVSS Move Indexed to Indexed PUSHL Store Literal at FSR2, Decrement FSR2 Syntax: MOVSS [zs], [zd] Syntax: PUSHL k Operands: 0 ≤ zs ≤ 127 0 ≤ zd ≤ 127 Operation: ((FSR2) + zs) → ((FSR2) + zd) Status Affected: None Encoding: 1st word (source) 2nd word (dest.) 1110 1111 Description 1011 xxxx 1zzz xzzz zzzzs zzzzd The contents of the source register are moved to the destination register. The addresses of the source and destination registers are determined by adding the 7-bit literal offsets ‘zs’ or ‘zd’, respectively, to the value of FSR2. Both registers can be located anywhere in the 4096-byte data memory space (000h to FFFh). The MOVSS instruction cannot use the PCL, TOSU, TOSH or TOSL as the destination register. If the resultant source address points to an indirect addressing register, the value returned will be 00h. If the resultant destination address points to an indirect addressing register, the instruction will execute as a NOP. Words: 2 Cycles: 2 Operands: 0 ≤ k ≤ 255 Operation: k → (FSR2), FSR2 – 1→ FSR2 Status Affected: None Encoding: 1111 1010 kkkk kkkk Description: The 8-bit literal ‘k’ is written to the data memory address specified by FSR2. FSR2 is decremented by ‘1’ after the operation. This instruction allows users to push values onto a software stack. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read ‘k’ Process data Write to destination Example: PUSHL 08h Before Instruction FSR2H:FSR2L Memory (01ECh) = = 01ECh 00h After Instruction FSR2H:FSR2L Memory (01ECh) = = 01EBh 08h Q Cycle Activity: Q1 Decode Decode Q2 Q3 Determine Determine source addr source addr Determine dest addr Example: MOVSS Before Instruction FSR2 Contents of 85h Contents of 86h After Instruction FSR2 Contents of 85h Contents of 86h DS39760D-page 258 Determine dest addr Q4 Read source reg Write to dest reg [05h], [06h] = 80h = 33h = 11h = 80h = 33h = 33h © 2008 Microchip Technology Inc. PIC18F2450/4450 SUBFSR Subtract Literal from FSR SUBULNK Syntax: SUBFSR f, k Syntax: SUBULNK k Operands: 0 ≤ k ≤ 63 Operands: 0 ≤ k ≤ 63 f ∈ [ 0, 1, 2 ] Operation: Operation: FSRf – k → FSRf Status Affected: None Encoding: 1110 FSR2 – k → FSR2, (TOS) → PC Status Affected: None 1001 ffkk kkkk Description: The 6-bit literal ‘k’ is subtracted from the contents of the FSR specified by ‘f’. Words: 1 Cycles: 1 Encoding: 1110 Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Before Instruction FSR2 = After Instruction FSR2 = SUBFSR 2, 23h 1001 11kk kkkk Description: The 6-bit literal ‘k’ is subtracted from the contents of the FSR2. A RETURN is then executed by loading the PC with the TOS. The instruction takes two cycles to execute; a NOP is performed during the second cycle. This may be thought of as a special case of the SUBFSR instruction, where f = 3 (binary ‘11’); it operates only on FSR2. Words: 1 Cycles: 2 Q Cycle Activity: Example: Subtract Literal from FSR2 and Return Q Cycle Activity: Q1 Q2 Q3 Q4 03FFh Decode Read register ‘f’ Process Data Write to destination 03DCh No Operation No Operation No Operation No Operation Example: © 2008 Microchip Technology Inc. SUBULNK 23h Before Instruction FSR2 = PC = 03FFh 0100h After Instruction FSR2 = PC = 03DCh (TOS) DS39760D-page 259 PIC18F2450/4450 19.2.3 Note: BYTE-ORIENTED AND BIT-ORIENTED INSTRUCTIONS IN INDEXED LITERAL OFFSET MODE Enabling the PIC18 instruction set extension may cause legacy applications to behave erratically or fail entirely. In addition to eight new commands in the extended set, enabling the extended instruction set also enables Indexed Literal Offset Addressing mode (Section 5.6.1 “Indexed Addressing with Literal Offset”). This has a significant impact on the way that many commands of the standard PIC18 instruction set are interpreted. When the extended set is disabled, addresses embedded in opcodes are treated as literal memory locations: either as a location in the Access Bank (‘a’ = 0) or in a GPR bank designated by the BSR (‘a’ = 1). When the extended instruction set is enabled and ‘a’ = 0, however, a file register argument of 5Fh or less is interpreted as an offset from the pointer value in FSR2 and not as a literal address. For practical purposes, this means that all instructions that use the Access RAM bit as an argument – that is, all byteoriented and bit-oriented instructions, or almost half of the core PIC18 instructions – may behave differently when the extended instruction set is enabled. When the content of FSR2 is 00h, the boundaries of the Access RAM are essentially remapped to their original values. This may be useful in creating backward compatible code. If this technique is used, it may be necessary to save the value of FSR2 and restore it when moving back and forth between C and assembly routines in order to preserve the Stack Pointer. Users must also keep in mind the syntax requirements of the extended instruction set (see Section 19.2.3.1 “Extended Instruction Syntax with Standard PIC18 Commands”). 19.2.3.1 Extended Instruction Syntax with Standard PIC18 Commands When the extended instruction set is enabled, the file register argument, ‘f’, in the standard byte-oriented and bit-oriented commands is replaced with the literal offset value, ‘k’. As already noted, this occurs only when ‘f’ is less than or equal to 5Fh. When an offset value is used, it must be indicated by square brackets (“[ ]”). As with the extended instructions, the use of brackets indicates to the compiler that the value is to be interpreted as an index or an offset. Omitting the brackets, or using a value greater than 5Fh within brackets, will generate an error in the MPASM Assembler. If the index argument is properly bracketed for Indexed Literal Offset Addressing mode, the Access RAM argument is never specified; it will automatically be assumed to be ‘0’. This is in contrast to standard operation (extended instruction set disabled) when ‘a’ is set on the basis of the target address. Declaring the Access RAM bit in this mode will also generate an error in the MPASM Assembler. The destination argument, ‘d’, functions as before. In the latest versions of the MPASM assembler, language support for the extended instruction set must be explicitly invoked. This is done with either the command line option, /y, or the PE directive in the source listing. 19.2.4 CONSIDERATIONS WHEN ENABLING THE EXTENDED INSTRUCTION SET It is important to note that the extensions to the instruction set may not be beneficial to all users. In particular, users who are not writing code that uses a software stack may not benefit from using the extensions to the instruction set. Although the Indexed Literal Offset Addressing mode can be very useful for dynamic stack and pointer manipulation, it can also be very annoying if a simple arithmetic operation is carried out on the wrong register. Users who are accustomed to the PIC18 programming must keep in mind that, when the extended instruction set is enabled, register addresses of 5Fh or less are used for Indexed Literal Offset Addressing. Additionally, the Indexed Literal Offset Addressing mode may create issues with legacy applications written to the PIC18 assembler. This is because instructions in the legacy code may attempt to address registers in the Access Bank below 5Fh. Since these addresses are interpreted as literal offsets to FSR2 when the instruction set extension is enabled, the application may read or write to the wrong data addresses. Representative examples of typical byte-oriented and bit-oriented instructions in the Indexed Literal Offset Addressing mode are provided on the following page to show how execution is affected. The operand conditions shown in the examples are applicable to all instructions of these types. When porting an application to the PIC18F2450/4450, it is very important to consider the type of code. A large, re-entrant application that is written in ‘C’ and would benefit from efficient compilation will do well when using the instruction set extensions. Legacy applications that heavily use the Access Bank will most likely not benefit from using the extended instruction set. DS39760D-page 260 © 2008 Microchip Technology Inc. PIC18F2450/4450 ADD W to Indexed (Indexed Literal Offset mode) BSF Bit Set Indexed (Indexed Literal Offset mode) Syntax: ADDWF Syntax: BSF [k], b Operands: 0 ≤ k ≤ 95 d ∈ [0,1] Operands: 0 ≤ f ≤ 95 0≤b≤7 Operation: (W) + ((FSR2) + k) → dest Operation: 1 → ((FSR2) + k)<b> Status Affected: N, OV, C, DC, Z Status Affected: None ADDWF Encoding: [k] {,d} 0010 Description: 01d0 kkkk kkkk The contents of W are added to the contents of the register indicated by FSR2, offset by the value ‘k’. If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’ (default). Encoding: 1000 bbb0 kkkk kkkk Description: Bit ‘b’ of the register indicated by FSR2, offset by the value ‘k’, is set. Words: 1 Cycles: 1 Q Cycle Activity: Words: 1 Q1 Q2 Q3 Q4 Cycles: 1 Decode Read register ‘f’ Process Data Write to destination Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read ‘k’ Process Data Write to destination Example: ADDWF Before Instruction W OFST FSR2 Contents of 0A2Ch After Instruction W Contents of 0A2Ch [OFST] ,0 = = = 17h 2Ch 0A00h = 20h = 37h = 20h Example: BSF Before Instruction FLAG_OFST FSR2 Contents of 0A0Ah After Instruction Contents of 0A0Ah [FLAG_OFST], 7 = = 0Ah 0A00h = 55h = D5h SETF Set Indexed (Indexed Literal Offset mode) Syntax: SETF [k] Operands: 0 ≤ k ≤ 95 Operation: FFh → ((FSR2) + k) Status Affected: None Encoding: 0110 1000 kkkk kkkk Description: The contents of the register indicated by FSR2, offset by ‘k’, are set to FFh. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read ‘k’ Process Data Write register Example: SETF Before Instruction OFST FSR2 Contents of 0A2Ch After Instruction Contents of 0A2Ch © 2008 Microchip Technology Inc. [OFST] = = 2Ch 0A00h = 00h = FFh DS39760D-page 261 PIC18F2450/4450 19.2.5 SPECIAL CONSIDERATIONS WITH MICROCHIP MPLAB® IDE TOOLS The latest versions of Microchip’s software tools have been designed to fully support the extended instruction set of the PIC18F2450/4450 family of devices. This includes the MPLAB C18 C compiler, MPASM Assembly language and MPLAB Integrated Development Environment (IDE). When selecting a target device for software development, MPLAB IDE will automatically set default Configuration bits for that device. The default setting for the XINST Configuration bit is ‘0’, disabling the extended instruction set and Indexed Literal Offset Addressing mode. For proper execution of applications developed to take advantage of the extended instruction set, XINST must be set during programming. DS39760D-page 262 To develop software for the extended instruction set, the user must enable support for the instructions and the Indexed Addressing mode in their language tool(s). Depending on the environment being used, this may be done in several ways: • A menu option, or dialog box within the environment, that allows the user to configure the language tool and its settings for the project • A command line option • A directive in the source code These options vary between different compilers, assemblers and development environments. Users are encouraged to review the documentation accompanying their development systems for the appropriate information. © 2008 Microchip Technology Inc. PIC18F2450/4450 20.0 DEVELOPMENT SUPPORT The PIC® microcontrollers are supported with a full range of hardware and software development tools: • Integrated Development Environment - MPLAB® IDE Software • Assemblers/Compilers/Linkers - MPASMTM Assembler - MPLAB C18 and MPLAB C30 C Compilers - MPLINKTM Object Linker/ MPLIBTM Object Librarian - MPLAB ASM30 Assembler/Linker/Library • Simulators - MPLAB SIM Software Simulator • Emulators - MPLAB ICE 2000 In-Circuit Emulator - MPLAB REAL ICE™ In-Circuit Emulator • In-Circuit Debugger - MPLAB ICD 2 • Device Programmers - PICSTART® Plus Development Programmer - MPLAB PM3 Device Programmer - PICkit™ 2 Development Programmer • Low-Cost Demonstration and Development Boards and Evaluation Kits 20.1 MPLAB Integrated Development Environment Software The MPLAB IDE software brings an ease of software development previously unseen in the 8/16-bit microcontroller market. The MPLAB IDE is a Windows® operating system-based application that contains: • A single graphical interface to all debugging tools - Simulator - Programmer (sold separately) - Emulator (sold separately) - In-Circuit Debugger (sold separately) • A full-featured editor with color-coded context • A multiple project manager • Customizable data windows with direct edit of contents • High-level source code debugging • Visual device initializer for easy register initialization • Mouse over variable inspection • Drag and drop variables from source to watch windows • Extensive on-line help • Integration of select third party tools, such as HI-TECH Software C Compilers and IAR C Compilers The MPLAB IDE allows you to: • Edit your source files (either assembly or C) • One touch assemble (or compile) and download to PIC MCU emulator and simulator tools (automatically updates all project information) • Debug using: - Source files (assembly or C) - Mixed assembly and C - Machine code MPLAB IDE supports multiple debugging tools in a single development paradigm, from the cost-effective simulators, through low-cost in-circuit debuggers, to full-featured emulators. This eliminates the learning curve when upgrading to tools with increased flexibility and power. © 2008 Microchip Technology Inc. DS39760D-page 263 PIC18F2450/4450 20.2 MPASM Assembler The MPASM Assembler is a full-featured, universal macro assembler for all PIC MCUs. The MPASM Assembler generates relocatable object files for the MPLINK Object Linker, Intel® standard HEX files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and generated machine code and COFF files for debugging. The MPASM Assembler features include: • Integration into MPLAB IDE projects • User-defined macros to streamline assembly code • Conditional assembly for multi-purpose source files • Directives that allow complete control over the assembly process 20.3 MPLAB C18 and MPLAB C30 C Compilers The MPLAB C18 and MPLAB C30 Code Development Systems are complete ANSI C compilers for Microchip’s PIC18 and PIC24 families of microcontrollers and the dsPIC30 and dsPIC33 family of digital signal controllers. These compilers provide powerful integration capabilities, superior code optimization and ease of use not found with other compilers. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. 20.4 MPLINK Object Linker/ MPLIB Object Librarian The MPLINK Object Linker combines relocatable objects created by the MPASM Assembler and the MPLAB C18 C Compiler. It can link relocatable objects from precompiled libraries, using directives from a linker script. 20.5 MPLAB ASM30 Assembler, Linker and Librarian MPLAB ASM30 Assembler produces relocatable machine code from symbolic assembly language for dsPIC30F devices. MPLAB C30 C Compiler uses the assembler to produce its object file. The assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. Notable features of the assembler include: • • • • • • Support for the entire dsPIC30F instruction set Support for fixed-point and floating-point data Command line interface Rich directive set Flexible macro language MPLAB IDE compatibility 20.6 MPLAB SIM Software Simulator The MPLAB SIM Software Simulator allows code development in a PC-hosted environment by simulating the PIC MCUs and dsPIC® DSCs on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a comprehensive stimulus controller. Registers can be logged to files for further run-time analysis. The trace buffer and logic analyzer display extend the power of the simulator to record and track program execution, actions on I/O, most peripherals and internal registers. The MPLAB SIM Software Simulator fully supports symbolic debugging using the MPLAB C18 and MPLAB C30 C Compilers, and the MPASM and MPLAB ASM30 Assemblers. The software simulator offers the flexibility to develop and debug code outside of the hardware laboratory environment, making it an excellent, economical software development tool. The MPLIB Object Librarian manages the creation and modification of library files of precompiled code. When a routine from a library is called from a source file, only the modules that contain that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. The object linker/library features include: • Efficient linking of single libraries instead of many smaller files • Enhanced code maintainability by grouping related modules together • Flexible creation of libraries with easy module listing, replacement, deletion and extraction DS39760D-page 264 © 2008 Microchip Technology Inc. PIC18F2450/4450 20.7 MPLAB ICE 2000 High-Performance In-Circuit Emulator The MPLAB ICE 2000 In-Circuit Emulator is intended to provide the product development engineer with a complete microcontroller design tool set for PIC microcontrollers. Software control of the MPLAB ICE 2000 In-Circuit Emulator is advanced by the MPLAB Integrated Development Environment, which allows editing, building, downloading and source debugging from a single environment. The MPLAB ICE 2000 is a full-featured emulator system with enhanced trace, trigger and data monitoring features. Interchangeable processor modules allow the system to be easily reconfigured for emulation of different processors. The architecture of the MPLAB ICE 2000 In-Circuit Emulator allows expansion to support new PIC microcontrollers. The MPLAB ICE 2000 In-Circuit Emulator system has been designed as a real-time emulation system with advanced features that are typically found on more expensive development tools. The PC platform and Microsoft® Windows® 32-bit operating system were chosen to best make these features available in a simple, unified application. 20.8 MPLAB REAL ICE In-Circuit Emulator System MPLAB REAL ICE In-Circuit Emulator System is Microchip’s next generation high-speed emulator for Microchip Flash DSC and MCU devices. It debugs and programs PIC® Flash MCUs and dsPIC® Flash DSCs with the easy-to-use, powerful graphical user interface of the MPLAB Integrated Development Environment (IDE), included with each kit. The MPLAB REAL ICE probe is connected to the design engineer’s PC using a high-speed USB 2.0 interface and is connected to the target with either a connector compatible with the popular MPLAB ICD 2 system (RJ11) or with the new high-speed, noise tolerant, LowVoltage Differential Signal (LVDS) interconnection (CAT5). 20.9 MPLAB ICD 2 In-Circuit Debugger Microchip’s In-Circuit Debugger, MPLAB ICD 2, is a powerful, low-cost, run-time development tool, connecting to the host PC via an RS-232 or high-speed USB interface. This tool is based on the Flash PIC MCUs and can be used to develop for these and other PIC MCUs and dsPIC DSCs. The MPLAB ICD 2 utilizes the in-circuit debugging capability built into the Flash devices. This feature, along with Microchip’s In-Circuit Serial ProgrammingTM (ICSPTM) protocol, offers costeffective, in-circuit Flash debugging from the graphical user interface of the MPLAB Integrated Development Environment. This enables a designer to develop and debug source code by setting breakpoints, single stepping and watching variables, and CPU status and peripheral registers. Running at full speed enables testing hardware and applications in real time. MPLAB ICD 2 also serves as a development programmer for selected PIC devices. 20.10 MPLAB PM3 Device Programmer The MPLAB PM3 Device Programmer is a universal, CE compliant device programmer with programmable voltage verification at VDDMIN and VDDMAX for maximum reliability. It features a large LCD display (128 x 64) for menus and error messages and a modular, detachable socket assembly to support various package types. The ICSP™ cable assembly is included as a standard item. In Stand-Alone mode, the MPLAB PM3 Device Programmer can read, verify and program PIC devices without a PC connection. It can also set code protection in this mode. The MPLAB PM3 connects to the host PC via an RS-232 or USB cable. The MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices and incorporates an SD/MMC card for file storage and secure data applications. MPLAB REAL ICE is field upgradeable through future firmware downloads in MPLAB IDE. In upcoming releases of MPLAB IDE, new devices will be supported, and new features will be added, such as software breakpoints and assembly code trace. MPLAB REAL ICE offers significant advantages over competitive emulators including low-cost, full-speed emulation, real-time variable watches, trace analysis, complex breakpoints, a ruggedized probe interface and long (up to three meters) interconnection cables. © 2008 Microchip Technology Inc. DS39760D-page 265 PIC18F2450/4450 20.11 PICSTART Plus Development Programmer 20.13 Demonstration, Development and Evaluation Boards The PICSTART Plus Development Programmer is an easy-to-use, low-cost, prototype programmer. It connects to the PC via a COM (RS-232) port. MPLAB Integrated Development Environment software makes using the programmer simple and efficient. The PICSTART Plus Development Programmer supports most PIC devices in DIP packages up to 40 pins. Larger pin count devices, such as the PIC16C92X and PIC17C76X, may be supported with an adapter socket. The PICSTART Plus Development Programmer is CE compliant. A wide variety of demonstration, development and evaluation boards for various PIC MCUs and dsPIC DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for adding custom circuitry and provide application firmware and source code for examination and modification. 20.12 PICkit 2 Development Programmer The PICkit™ 2 Development Programmer is a low-cost programmer and selected Flash device debugger with an easy-to-use interface for programming many of Microchip’s baseline, mid-range and PIC18F families of Flash memory microcontrollers. The PICkit 2 Starter Kit includes a prototyping development board, twelve sequential lessons, software and HI-TECH’s PICC™ Lite C compiler, and is designed to help get up to speed quickly using PIC® microcontrollers. The kit provides everything needed to program, evaluate and develop applications using Microchip’s powerful, mid-range Flash memory family of microcontrollers. DS39760D-page 266 The boards support a variety of features, including LEDs, temperature sensors, switches, speakers, RS-232 interfaces, LCD displays, potentiometers and additional EEPROM memory. The demonstration and development boards can be used in teaching environments, for prototyping custom circuits and for learning about various microcontroller applications. In addition to the PICDEM™ and dsPICDEM™ demonstration/development board series of circuits, Microchip has a line of evaluation kits and demonstration software for analog filter design, KEELOQ® security ICs, CAN, IrDA®, PowerSmart battery management, SEEVAL® evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. Check the Microchip web page (www.microchip.com) for the complete list of demonstration, development and evaluation kits. © 2008 Microchip Technology Inc. PIC18F2450/4450 21.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings(†) Ambient temperature under bias.............................................................................................................. .-40°C to +85°C Storage temperature .............................................................................................................................. -65°C to +150°C Voltage on any pin with respect to VSS (except VDD and MCLR) ................................................... -0.3V to (VDD + 0.3V) Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +7.5V Voltage on MCLR with respect to VSS (Note 2) ......................................................................................... 0V to +13.25V Total power dissipation (Note 1) ...............................................................................................................................1.0W Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin ..............................................................................................................................250 mA Input clamp current, IIK (VI < 0 or VI > VDD)...................................................................................................................... ±20 mA Output clamp current, IOK (VO < 0 or VO > VDD) .............................................................................................................. ±20 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin ....................................................................................................25 mA Maximum current sunk by all ports .......................................................................................................................200 mA Maximum current sourced by all ports ..................................................................................................................200 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD – ∑ IOH} + ∑ {(VDD – VOH) x IOH} + ∑(VOL x IOL) 2: Voltage spikes below VSS at the MCLR/VPP/RE3 pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR/VPP/ RE3 pin, rather than pulling this pin directly to VSS. † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. © 2008 Microchip Technology Inc. DS39760D-page 267 PIC18F2450/4450 FIGURE 21-1: PIC18F2450/4450 VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL) 6.0V 5.5V Voltage 5.0V PIC18F2450/4450 4.5V 4.2V 4.0V 3.5V 3.0V 2.5V 2.0V 48 MHz Frequency FIGURE 21-2: PIC18LF2450/4450 VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL) 6.0V 5.5V Voltage 5.0V PIC18LF2450/4450 4.5V 4.2V 4.0V 3.5V 3.0V 2.5V 2.0V 40 MHz 4 MHz 48 MHz Frequency For 2.0V ≤ VDD < 4.2V: FMAX = (16.36 MHz/V) (VDDAPPMIN – 2.0V) + 4 MHz For 4.2V ≤ VDD: FMAX = 48 MHz Note: VDDAPPMIN is the minimum voltage of the PIC® device in the application. DS39760D-page 268 © 2008 Microchip Technology Inc. PIC18F2450/4450 21.1 DC Characteristics: Supply Voltage PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial PIC18F2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. Symbol D001 VDD D002 VDR Characteristic Supply Voltage Min Typ 2.0 3.0 — — Max Units 5.5 5.5 V V Conditions EC, HS, XT and Internal Oscillator modes HSPLL, XTPLL, ECPIO and ECPLL Oscillator modes RAM Data Retention 1.5 — — V Voltage(1) VDD Start Voltage — — 0.7 V See Section 4.3 “Power-on Reset (POR)” D003 VPOR to ensure internal Power-on for details Reset signal VDD Rise Rate 0.05 — — V/ms See Section 4.3 “Power-on Reset (POR)” D004 SVDD to Ensure Internal Power-on for details Reset Signal Brown-out Reset Voltage D005 VBOR BORV1:BORV0 = 11 2.00 2.11 2.22 V BORV1:BORV0 = 10 2.65 2.79 2.93 V BORV1:BORV0 = 01 4.11 4.33 4.55 V BORV1:BORV0 = 00 4.36 4.59 4.82 V Legend: Shading of rows is to assist in readability of the table. Note 1: This is the limit to which VDD can be lowered in Sleep mode, or during a device Reset, without losing RAM data. © 2008 Microchip Technology Inc. DS39760D-page 269 PIC18F2450/4450 21.2 DC Characteristics: Power-Down and Supply Current PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial PIC18F2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. Device Typ Max Units Power-Down Current (IPD)(1) PIC18LF2450/4450 0.1 0.1 0.95 1.0 μA μA -40°C +25°C 0.1 0.1 0.1 1.5 0.1 5.0 1.4 2.0 8.0 19 μA μA μA μA μA +85°C -40°C +25°C +85°C -40°C PIC18LF2450/4450 All devices Legend: Note 1: 2: 3: 4: Conditions VDD = 2.0V (Sleep mode) VDD = 3.0V (Sleep mode) VDD = 5.0V 0.1 2.0 μA +25°C (Sleep mode) 2.5 15 μA +85°C Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS; MCLR = VDD; WDT enabled/disabled as specified. Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature crystals are available at a much higher cost. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. DS39760D-page 270 © 2008 Microchip Technology Inc. PIC18F2450/4450 21.2 DC Characteristics: Power-Down and Supply Current PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) (Continued) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial PIC18F2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. Device Supply Current (IDD)(2) PIC18LF2450/4450 PIC18LF2450/4450 All devices Legend: Note 1: 2: 3: 4: Typ Max Units Conditions 10 10 32 30 μA μA -40°C +25°C 12 35 30 25 95 29 63 60 57 168 μA μA μA μA μA +85°C -40°C +25°C +85°C -40°C VDD = 2.0V VDD = 3.0V FOSC = 31 kHz (RC_RUN mode, INTRC source) VDD = 5.0V 75 160 μA +25°C 65 152 μA +85°C PIC18LF2450/4450 2.3 8 μA -40°C VDD = 2.0V 2.5 8 μA +25°C 3.3 11 μA +85°C PIC18LF2450/4450 3.3 11 μA -40°C FOSC = 31 kHz 3.6 11 μA +25°C VDD = 3.0V (RC_IDLE mode, INTRC source) 4.0 15 μA +85°C All devices 6.5 16 μA -40°C VDD = 5.0V 7.0 16 μA +25°C 9.0 36 μA +85°C Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS; MCLR = VDD; WDT enabled/disabled as specified. Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature crystals are available at a much higher cost. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. © 2008 Microchip Technology Inc. DS39760D-page 271 PIC18F2450/4450 21.2 DC Characteristics: Power-Down and Supply Current PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) (Continued) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial PIC18F2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. Device Supply Current (IDD)(2) PIC18LF2450/4450 PIC18LF2450/4450 All devices Legend: Note 1: 2: 3: 4: Typ Max Units Conditions 200 200 500 500 μA μA -40°C +25°C 200 500 400 360 1.0 500 650 650 650 1.6 μA μA μA μA mA +85°C -40°C +25°C +85°C -40°C VDD = 2.0V VDD = 3.0V FOSC = 1 MHZ (PRI_RUN, EC oscillator) VDD = 5.0V 0.9 1.5 mA +25°C 0.8 1.4 mA +85°C PIC18LF2450/4450 0.53 2.0 mA -40°C VDD = 2.0V 0.53 2.0 mA +25°C 0.55 2.0 mA +85°C PIC18LF2450/4450 1.0 3.0 mA -40°C FOSC = 4 MHz 0.9 3.0 mA +25°C VDD = 3.0V (PRI_RUN, EC oscillator) 0.9 3.0 mA +85°C All devices 2.0 6.0 mA -40°C VDD = 5.0V 1.9 6.0 mA +25°C 1.8 6.0 mA +85°C All devices 11.0 35 mA -40°C VDD = 4.2V 11.0 35 mA +25°C FOSC = 40 MHZ 11.3 35 mA +85°C (PRI_RUN, All devices 14.0 40 mA -40°C EC oscillator) VDD = 5.0V 14.0 40 mA +25°C 14.5 40 mA +85°C All devices 20 40 mA -40°C 20 40 mA +25°C VDD = 4.2V FOSC = 48 MHZ 20 40 mA +85°C (PRI_RUN, All devices 25 50 mA -40°C EC oscillator) VDD = 5.0V 25 50 mA +25°C 25 50 mA +85°C Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS; MCLR = VDD; WDT enabled/disabled as specified. Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature crystals are available at a much higher cost. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. DS39760D-page 272 © 2008 Microchip Technology Inc. PIC18F2450/4450 21.2 DC Characteristics: Power-Down and Supply Current PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) (Continued) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial PIC18F2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. Device Supply Current (IDD)(2) PIC18LF2450/4450 PIC18LF2450/4450 All devices Legend: Note 1: 2: 3: 4: Typ Max Units Conditions 50 50 130 120 μA μA -40°C +25°C 50 75 80 80 150 115 270 250 240 480 μA μA μA μA μA +85°C -40°C +25°C +85°C -40°C VDD = 2.0V VDD = 3.0V FOSC = 1 MHz (PRI_IDLE mode, EC oscillator) VDD = 5.0V 150 450 μA +25°C 150 430 μA +85°C PIC18LF2450/4450 190 475 μA -40°C VDD = 2.0V 195 450 μA +25°C 200 430 μA +85°C PIC18LF2450/4450 295 900 μA -40°C FOSC = 4 MHz 300 850 μA +25°C VDD = 3.0V (PRI_IDLE mode, EC oscillator) 310 810 μA +85°C All devices 560 1.5 mA -40°C VDD = 5.0V 570 1.4 mA +25°C 580 1.3 mA +85°C All devices 4.4 16 mA -40°C 4.5 16 mA +25°C VDD = 4.2V FOSC = 40 MHz 4.6 16 mA +85°C (PRI_IDLE mode, All devices 5.5 18 mA -40°C EC oscillator) VDD = 5.0V 5.6 18 mA +25°C 5.8 18 mA +85°C All devices 8.0 18 mA -40°C 8.1 18 mA +25°C VDD = 4.2V FOSC = 48 MHz 8.2 18 mA +85°C (PRI_IDLE mode, All devices 9.8 21 mA -40°C EC oscillator) VDD = 5.0V 10.0 21 mA +25°C 10.5 21 mA +85°C Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS; MCLR = VDD; WDT enabled/disabled as specified. Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature crystals are available at a much higher cost. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. © 2008 Microchip Technology Inc. DS39760D-page 273 PIC18F2450/4450 21.2 DC Characteristics: Power-Down and Supply Current PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) (Continued) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial PIC18F2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. Device Supply Current (IDD)(2) PIC18LF2450/4450 PIC18LF2450/4450 All devices Legend: Note 1: 2: 3: 4: Typ Max Units Conditions 13 15 40 40 μA μA -40°C +25°C 17 40 32 25 100 40 76 70 67 150 μA μA μA μA μA +85°C -40°C +25°C +85°C -40°C VDD = 2.0V VDD = 3.0V FOSC = 32 kHz(3) (SEC_RUN mode, Timer1 as clock) VDD = 5.0V 80 150 μA +25°C 70 150 μA +85°C PIC18LF2450/4450 5.6 12 μA -40°C VDD = 2.0V 7.0 12 μA +25°C 8.3 12 μA +85°C PIC18LF2450/4450 6.5 15 μA -40°C FOSC = 32 kHz(3) 8.0 15 μA +25°C VDD = 3.0V (SEC_IDLE mode, Timer1 as clock) 9.5 15 μA +85°C All devices 8.7 25 μA -40°C VDD = 5.0V 10.2 25 μA +25°C 13.0 36 μA +85°C Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS; MCLR = VDD; WDT enabled/disabled as specified. Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature crystals are available at a much higher cost. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. DS39760D-page 274 © 2008 Microchip Technology Inc. PIC18F2450/4450 21.2 DC Characteristics: Power-Down and Supply Current PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) (Continued) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial PIC18F2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. D022 (ΔIWDT) D022A (ΔIBOR) D022B (ΔILVD) D025 (ΔIOSCB) D026 (ΔIAD) Legend: Note 1: 2: 3: 4: Device Typ Max Units Conditions Module Differential Currents (ΔIWDT, ΔIBOR, ΔILVD, ΔIOSCB, ΔIAD) Watchdog Timer 1.3 3.8 μA -40°C 1.5 3.8 μA +25°C Brown-out Reset(4) 2.3 1.8 2.0 3.0 3.3 3.8 4.6 4.6 4.6 10 μA μA μA μA μA +85°C -40°C +25°C +85°C -40°C 3.6 3.9 40 45 10 10 52 63 μA μA μA μA +25°C +85°C -40°C to +85°C -40°C to +85°C 0 2 μA -40°C to +85°C VDD = 2.0V VDD = 3.0V VDD = 5.0V VDD = 3.0V VDD = 5.0V Sleep mode, BOREN1:BOREN0 = 10 22 47 μA -40°C to +85°C VDD = 2.0V 25 58 μA -40°C to +85°C VDD = 3.0V 29 69 μA -40°C to +85°C VDD = 5.0V Timer1 Oscillator 1.5 4.5 μA -40°C VDD = 2.0V 1.2 4.5 μA +25°C 32 kHz on Timer1(3) 1.6 4.5 μA +85°C 1.7 6.0 μA -40°C VDD = 3.0V 1.8 6.0 μA +25°C 32 kHz on Timer1(3) 2.0 6.0 μA +85°C 1.4 8.0 μA -40°C VDD = 5.0V 1.5 8.0 μA +25°C 32 kHz on Timer1(3) 1.9 8.0 μA +85°C A/D Converter 0.2 2.0 μA -40°C to +85°C VDD = 2.0V 0.2 2.0 μA -40°C to +85°C VDD = 3.0V A/D on, not converting 0.2 2.0 μA -40°C to +85°C VDD = 5.0V Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS; MCLR = VDD; WDT enabled/disabled as specified. Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature crystals are available at a much higher cost. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. High/Low-Voltage Detect(4) © 2008 Microchip Technology Inc. DS39760D-page 275 PIC18F2450/4450 21.2 DC Characteristics: Power-Down and Supply Current PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) (Continued) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial PIC18F2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. ΔIUSBX ΔIPLL Device Legend: Note 1: 2: 3: 4: Max Units Conditions USB and Related Module Differential Currents (ΔIUSBx, ΔIPLL, ΔIUREG) USB Module 8.0 14.5 mA +25°C VDD = 3.3V with On-Chip Transceiver 12.4 20 mA +25°C VDD = 5.0V 96 MHz PLL (Oscillator Module) ΔIUREG Typ 1.2 1.2 80 3.0 4.8 125 mA mA μA +25°C +25°C +25°C VDD = 3.3V VDD = 5.0V VDD = 5.0V USB Internal Voltage USB Idle, Regulator UCON<SUSPND> = 1 Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS; MCLR = VDD; WDT enabled/disabled as specified. Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature crystals are available at a much higher cost. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. DS39760D-page 276 © 2008 Microchip Technology Inc. PIC18F2450/4450 21.2 DC Characteristics: Power-Down and Supply Current PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) (Continued) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial PIC18F2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. Device Typ Total USB Run Currents (ITUSB)(2) Primary Run with USB 29 Module, PLL and USB 29 Voltage Regulator 29 ITUSB Legend: Note 1: 2: 3: 4: Max Units 65 65 65 mA mA mA Conditions -40°C +25°C +85°C VDD = 5.0V VDD = 5.0V VDD = 5.0V EC+PLL 4 MHz input, 48 MHz PRI_RUN, USB module enabled in Full-Speed mode, USB VREG enabled, no bus traffic Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS; MCLR = VDD; WDT enabled/disabled as specified. Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature crystals are available at a much higher cost. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. © 2008 Microchip Technology Inc. DS39760D-page 277 PIC18F2450/4450 21.3 DC Characteristics: PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial DC CHARACTERISTICS Param No. Sym VIL Characteristic Min Max Units Conditions VSS 0.15 VDD V VDD < 4.5V — 0.8 V 4.5V ≤ VDD ≤ 5.5V Input Low Voltage I/O Ports (except RC4/RC5 in USB mode): D030 with TTL Buffer D030A D032 MCLR VSS 0.2 VDD V D032A OSC1 and T1OSI VSS 0.3 VDD V XT, HS, HSPLL modes(1) D033 OSC1 VSS 0.2 VDD V EC mode(1) 0.25 VDD + 0.8V VDD V VDD < 4.5V 2.0 VDD V 4.5V ≤ VDD ≤ 5.5V VIH Input High Voltage I/O Ports (except RC4/RC5 in USB mode): D040 with TTL Buffer D040A D042 MCLR 0.8 VDD VDD V D042A OSC1 and T1OSI 0.7 VDD VDD V XT, HS, HSPLL modes(1) D043 OSC1 0.8 VDD VDD V EC mode(1) — ±200 nA VDD = 5V — ±50 nA VDD = 3V IIL D060 Input Leakage Current(2,3) I/O Ports (except D+ and D-) D061 MCLR — ±1 μA Vss ≤ VPIN ≤ VDD D063 OSC1 — ±1 μA Vss ≤ VPIN ≤ VDD 50 400 μA VDD = 5V, VPIN = VSS D070 Note 1: 2: 3: 4: IPU Weak Pull-up Current IPURB PORTB Weak Pull-up Current In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the PIC® microcontroller be driven with an external clock while in RC mode. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as current sourced by the pin. Parameter is characterized but not tested. DS39760D-page 278 © 2008 Microchip Technology Inc. PIC18F2450/4450 21.3 DC Characteristics: PIC18F2450/4450 (Industrial) PIC18LF2450/4450 (Industrial) (Continued) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial DC CHARACTERISTICS Param No. Sym VOL Characteristic Min Max Units Conditions Output Low Voltage D080 I/O Ports (except RC4/RC5 in USB mode) — 0.6 V IOL = 8.5 mA, VDD = 4.5V, -40°C to +85°C D083 OSC2/CLKO (EC, ECIO modes) — 0.6 V IOL = 1.6 mA, VDD = 4.5V, -40°C to +85°C VOH Output High Voltage(3) D090 I/O Ports (except RC4/RC5 in USB mode) VDD – 0.7 — V IOH = -3.0 mA, VDD = 4.5V, -40°C to +85°C D092 OSC2/CLKO (EC, ECIO, ECPIO modes) VDD – 0.7 — V IOH = -1.3 mA, VDD = 4.5V, -40°C to +85°C D100(4) COSC2 OSC2 pin — 15 pF In XT and HS modes when external clock is used to drive OSC1 D101 — 50 pF To meet the AC Timing Specifications Capacitive Loading Specs on Output Pins CIO Note 1: 2: 3: 4: All I/O pins and OSC2 (in RC mode) In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the PIC® microcontroller be driven with an external clock while in RC mode. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as current sourced by the pin. Parameter is characterized but not tested. © 2008 Microchip Technology Inc. DS39760D-page 279 PIC18F2450/4450 TABLE 21-1: MEMORY PROGRAMMING REQUIREMENTS Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial DC Characteristics Param No. Sym Characteristic Min Typ† Max Units Conditions 9.00 — 13.25 V — — 10 mA E/W -40°C to +85°C Internal Program Memory Programming Specifications(1) D110 VIHH Voltage on MCLR/VPP/RE3 pin (Note 2) D113 IDDP Supply Current during Programming D130 EP Cell Endurance 10K 100K — D131 VPR VDD for Read VMIN — 5.5 D132 VIE VDD for Block Erase 4.5 — 5.5 V Using ICSP™ port D132A VIW VDD for Externally Timed Erase or Write 3.0 — 5.5 V Using ICSP port VMIN — 5.5 V VMIN = Minimum operating voltage Program Flash Memory V VMIN = Minimum operating voltage D132B VPEW VDD for Self-Timed Write D133 TIE ICSP™ Block Erase Cycle Time — 4 — ms VDD > 4.5V D133A TIW ICSP Erase or Write Cycle Time (externally timed) 1 — — ms VDD > 4.5V D133A TIW Self-Timed Write Cycle Time D134 TRETD Characteristic Retention — 2 — 40 100 — ms Year Provided no other specifications are violated † Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: These specifications are for programming the on-chip program memory through the use of table write instructions. 2: Required only if Single-Supply Programming is disabled. DS39760D-page 280 © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 21-2: USB MODULE SPECIFICATIONS Operating Conditions: -40°C < TA < +85°C (unless otherwise stated). Param No. Sym Characteristic Min Typ Max Units Comments Voltage on bus must be in this range for proper USB operation D313 VUSB USB Voltage 3.0 — 3.6 V D314 IIL Input Leakage on D+ or Dpin — — ±1 μA VSS ≤ VPIN ≤ VDD; pin at high-impedance D315 VILUSB Input Low Voltage for USB Buffer — — 0.8 V For VUSB range D316 VIHUSB Input High Voltage for USB Buffer 2.0 — — V For VUSB range D317 VCRS Crossover Voltage 1.3 2.0 V Voltage range for D+ and Dcrossover to occur D318 VDIFS Differential Input Sensitivity — — 0.2 V The difference between D+ and D- must exceed this value while VCM is met D319 VCM Differential Common Mode Range 0.8 — 2.5 V D320 ZOUT Driver Output Impedance 28 — 44 Ω D321 VOL Voltage Output Low 0.0 — 0.3 V 1.5 kΩ load connected to 3.6V D322 VOH Voltage Output High 2.8 — 3.6 V 15 kΩ load connected to ground TABLE 21-3: USB INTERNAL VOLTAGE REGULATOR SPECIFICATIONS Operating Conditions: -40°C < TA < +85°C (unless otherwise stated). Param No. Sym Characteristics Min Typ Max Units Comments D323 VUSBANA Regulator Output Voltage 3.0 — 3.6 V VDD > 4.0V(1) D324 CUSB 220 470 — nF Low ESR Note 1: If device VDD is less than 4.0V, the internal USB voltage regulator should be disabled and an external 3.0-3.6V supply should be provided on VUSB. External Filter Capacitor Value © 2008 Microchip Technology Inc. DS39760D-page 281 PIC18F2450/4450 FIGURE 21-3: HIGH/LOW-VOLTAGE DETECT CHARACTERISTICS For VDIRMAG = 1: VDD VHLVD (HLVDIF set by hardware) (HLVDIF can be cleared in software) VHLVD For VDIRMAG = 0: VDD HLVDIF TABLE 21-4: HIGH/LOW-VOLTAGE DETECT CHARACTERISTICS Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. D420 Sym Characteristic Min Typ Max Units HLVD Voltage on VDD HLVDL<3:0> = 0000 Transition High-to-Low HLVDL<3:0> = 0001 2.06 2.17 2.28 V 2.12 2.23 2.34 V HLVDL<3:0> = 0010 2.24 2.36 2.48 V DS39760D-page 282 HLVDL<3:0> = 0011 2.32 2.44 2.56 V HLVDL<3:0> = 0100 2.47 2.60 2.73 V HLVDL<3:0> = 0101 2.65 2.79 2.93 V HLVDL<3:0> = 0110 2.74 2.89 3.04 V HLVDL<3:0> = 0111 2.96 3.12 3.28 V HLVDL<3:0> = 1000 3.22 3.39 3.56 V HLVDL<3:0> = 1001 3.37 3.55 3.73 V HLVDL<3:0> = 1010 3.52 3.71 3.90 V HLVDL<3:0> = 1011 3.70 3.90 4.10 V HLVDL<3:0> = 1100 3.90 4.11 4.32 V HLVDL<3:0> = 1101 4.11 4.33 4.55 V HLVDL<3:0> = 1110 4.36 4.59 4.82 V Conditions © 2008 Microchip Technology Inc. PIC18F2450/4450 21.4 21.4.1 AC (Timing) Characteristics TIMING PARAMETER SYMBOLOGY The timing parameter symbols have been created using one of the following formats: 1. TppS2ppS 2. TppS T F Frequency Lowercase letters (pp) and their meanings: pp cc ck dt io CCP1 CLKO Data in I/O port :Uppercase Letters and their meanings S F Fall H High I Invalid (High-Impedance) L Low © 2008 Microchip Technology Inc. T Time mc osc wr t0 t1 MCLR OSC1 WR T0CKI T1CKI P R V Z Period Rise Valid High-Impedance High Low High Low DS39760D-page 283 PIC18F2450/4450 21.4.2 TIMING CONDITIONS Note: The temperature and voltages specified in Table 21-5 apply to all timing specifications unless otherwise noted. Figure 21-4 specifies the load conditions for the timing specifications. TABLE 21-5: Because of space limitations, the generic terms “PIC18FXXXX” and “PIC18LFXXXX” are used throughout this section to refer to the PIC18F2450/4450 and PIC18LF2450/ 4450 families of devices specifically and only those devices. TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC AC CHARACTERISTICS FIGURE 21-4: Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Operating voltage VDD range as described in DC spec Section 21.1 and Section 21.3 . LF parts operate for industrial temperatures only. LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS Load Condition 1 Load Condition 2 VDD/2 RL CL Pin VSS CL Pin RL = 464Ω VSS DS39760D-page 284 CL = 50 pF for all pins except OSC2/CLKO and including D and E outputs as ports © 2008 Microchip Technology Inc. PIC18F2450/4450 21.4.3 TIMING DIAGRAMS AND SPECIFICATIONS FIGURE 21-5: EXTERNAL CLOCK TIMING (ALL MODES EXCEPT PLL) Q4 Q1 Q2 Q3 Q4 Q1 OSC1 1 3 4 3 4 2 CLKO TABLE 21-6: Param. No. 1A 1 EXTERNAL CLOCK TIMING REQUIREMENTS Symbol FOSC TOSC Characteristic Min Max Units External CLKI Frequency(1) Oscillator Frequency(1) DC 48 MHz EC, ECIO Oscillator modes 0.2 1 MHz XT, XTPLL Oscillator modes 4 25 MHz HS Oscillator mode 4 25 MHz HSPLL Oscillator mode External CLKI Period(1) Oscillator Period(1) Time(1) Conditions 20.8 — ns EC, ECIO Oscillator modes 1,000 5,000 ns XT Oscillator mode 40 250 ns HS Oscillator mode 40 250 ns HSPLL Oscillator mode 2 TCY Instruction Cycle 83.3 — ns TCY = 4/FOSC 3 TosL, TosH External Clock in (OSC1) High or Low Time 30 — ns XT Oscillator mode 10 — ns HS Oscillator mode 4 TosR, TosF External Clock in (OSC1) Rise or Fall Time — 20 ns XT Oscillator mode — 7.5 ns HS Oscillator mode Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period for all configurations except PLL. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at “min.” values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the “max.” cycle time limit is “DC” (no clock) for all devices. © 2008 Microchip Technology Inc. DS39760D-page 285 PIC18F2450/4450 TABLE 21-7: Param No. PLL CLOCK TIMING SPECIFICATIONS (VDD = 3.0V TO 5.5V) Sym Characteristic F10 F11 FOSC Oscillator Frequency Range FSYS On-Chip VCO System Frequency F12 trc PLL Start-up Time (lock time) ΔCLK CLKO Stability (jitter) F13 Min Typ† Max Units 4 — — 96 48 — MHz MHz — — 2 ms -0.25 — +0.25 % Conditions † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. TABLE 21-8: AC CHARACTERISTICS: INTERNAL RC ACCURACY PIC18F2450/4450 (INDUSTRIAL) PIC18LF2450/4450 (INDUSTRIAL) PIC18LF2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial PIC18F2450/4450 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. Device Min Typ Max Units Conditions INTRC Accuracy @ Freq = 31 kHz(1) Legend: Note 1: PIC18LF2450/4450 26.562 — 35.938 kHz -40°C to +85°C VDD = 2.7-3.3V PIC18F2450/4450 26.562 — 35.938 kHz -40°C to +85°C VDD = 4.5-5.5V Shading of rows is to assist in readability of the table. INTRC frequency after calibration. DS39760D-page 286 © 2008 Microchip Technology Inc. PIC18F2450/4450 FIGURE 21-6: CLKO AND I/O TIMING Q1 Q4 Q2 Q3 OSC1 11 10 CLKO 12 13 14 18 19 16 I/O pin (Input) 15 17 I/O pin (Output) New Value Old Value 20, 21 Note: Refer to Figure 21-4 for load conditions. TABLE 21-9: Param No. CLKO AND I/O TIMING REQUIREMENTS Symbol Characteristic Min Typ Max Units Conditions 10 TosH2ckL OSC1 ↑ to CLKO ↓ — 75 200 ns (Note 1) 11 TosH2ckH OSC1 ↑ to CLKO ↑ — 75 200 ns (Note 1) 12 TckR CLKO Rise Time — 35 100 ns (Note 1) 13 TckF CLKO Fall Time — 35 100 ns (Note 1) CLKO ↓ to Port Out Valid — — 0.5 TCY + 20 ns (Note 1) 0.25 TCY + 25 — — ns (Note 1) (Note 1) 14 TckL2ioV 15 TioV2ckH Port In Valid before CLKO ↑ 16 TckH2ioI Port In Hold after CLKO ↑ 0 — — ns 17 TosH2ioV OSC1 ↑ (Q1 cycle) to Port Out Valid — 50 150 ns 18 TosH2ioI PIC18FXXXX 100 — — ns PIC18LFXXXX 200 — — ns 18A OSC1 ↑ (Q2 cycle) to Port Input Invalid (I/O in hold time) 19 TioV2osH Port Input Valid to OSC1 ↑ (I/O in setup time) 0 — — ns 20 TioR Port Output Rise Time 20A 21 TioF Port Output Fall Time 21A PIC18FXXXX — 10 25 ns PIC18LFXXXX — — 60 ns PIC18FXXXX — 10 25 ns PIC18LFXXXX — — 60 ns 22† TINP INTx Pin High or Low Time TCY — — ns 23† TRBP RB7:RB4 Change Interrupt High or Low Time TCY — — ns VDD = 2.0V VDD = 2.0V VDD = 2.0V † These parameters are asynchronous events not related to any internal clock edges. Note 1: Measurements are taken in RC mode, where CLKO output is 4 x TOSC. © 2008 Microchip Technology Inc. DS39760D-page 287 PIC18F2450/4450 FIGURE 21-7: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING VDD MCLR 30 Internal POR 33 PWRT Time-out 32 Oscillator Time-out Internal Reset Watchdog Timer Reset 31 34 34 I/O pins Note: Refer to Figure 21-4 for load conditions. FIGURE 21-8: BROWN-OUT RESET TIMING BVDD VDD 35 VBGAP = 1.2V VIRVST Enable Internal Reference Voltage Internal Reference Voltage Stable 36 TABLE 21-10: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER AND BROWN-OUT RESET REQUIREMENTS Param. Symbol No. Characteristic Min Typ Max Units 30 TmcL MCLR Pulse Width (low) 2 — — μs 31 TWDT Watchdog Timer Time-out Period (no postscaler) — 4.00 4.6 ms 32 TOST Oscillator Start-up Timer Period 1024 TOSC — 1024 TOSC — 33 TPWRT Power-up Timer Period — 65.5 75 ms 34 TIOZ I/O High-Impedance from MCLR Low or Watchdog Timer Reset — 2 — μs 35 TBOR Brown-out Reset Pulse Width 36 TIRVST Time for Internal Reference Voltage to become Stable 37 TLVD Low-Voltage Detect Pulse Width 38 TCSD CPU Start-up Time 39 TIOBST Time for INTRC to Stabilize DS39760D-page 288 200 — — μs — 20 50 μs 200 — — μs 5 — 10 μs — 1 — ms Conditions TOSC = OSC1 period VDD ≤ BVDD (see D005) VDD ≤ VLVD © 2008 Microchip Technology Inc. PIC18F2450/4450 FIGURE 21-9: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS T0CKI 41 40 42 T1OSO/T1CKI 46 45 47 48 TMR0 or TMR1 Note: Refer to Figure 21-4 for load conditions. TABLE 21-11: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS Param Symbol No. Characteristic 40 Tt0H T0CKI High Pulse Width 41 Tt0L T0CKI Low Pulse Width 42 Tt0P T0CKI Period No prescaler With prescaler No prescaler With prescaler No prescaler With prescaler 45 Tt1H T1CKI High Time Synchronous, no prescaler PIC18FXXXX 47 Tt1L T1CKI Low Time 0.5 TCY + 20 — ns 10 — ns 0.5 TCY + 20 — ns 10 — ns TCY + 10 — ns Greater of: 20 ns or (TCY + 40)/N — ns 0.5 TCY + 20 — ns 10 — ns PIC18LFXXXX 25 — ns PIC18FXXXX 30 — ns Synchronous, no prescaler 50 — ns 0.5 TCY + 5 — ns Conditions N = prescale value (1, 2, 4,..., 256) VDD = 2.0V VDD = 2.0V Synchronous, with prescaler PIC18FXXXX 10 — ns PIC18LFXXXX 25 — ns Asynchronous PIC18FXXXX 30 — ns PIC18LFXXXX 50 — ns VDD = 2.0V Greater of: 20 ns or (TCY + 40)/N — ns N = prescale value (1, 2, 4, 8) Tt1P T1CKI Input Period Ft1 T1CKI Oscillator Input Frequency Range Synchronous Tcke2tmrI Delay from External T1CKI Clock Edge to Timer Increment © 2008 Microchip Technology Inc. Units Asynchronous Asynchronous 48 Max Synchronous, with prescaler PIC18LFXXXX 46 Min 60 — ns DC 50 kHz 2 TOSC 7 TOSC — VDD = 2.0V DS39760D-page 289 PIC18F2450/4450 FIGURE 21-10: CAPTURE/COMPARE/PWM TIMINGS (CCP MODULE) CCP1 (Capture Mode) 50 51 52 CCP1 (Compare or PWM Mode) 53 Note: 54 Refer to Figure 21-4 for load conditions. TABLE 21-12: CAPTURE/COMPARE/PWM REQUIREMENTS Param Symbol No. 50 51 TccL TccH Characteristic CCP1 Input Low Time No prescaler CCP1 Input High Time No prescaler With prescaler With prescaler 52 TccP CCP1 Input Period 53 TccR CCP1 Output Fall Time 54 TccF CCP1 Output Fall Time DS39760D-page 290 PIC18FXXXX PIC18LFXXXX Min Max Units 0.5 TCY + 20 — ns 10 — ns 20 — ns 0.5 TCY + 20 — ns Conditions VDD = 2.0V PIC18FXXXX 10 — ns PIC18LFXXXX 20 — ns VDD = 2.0V 3 TCY + 40 N — ns N = prescale value (1, 4 or 16) PIC18FXXXX — 25 ns PIC18LFXXXX — 45 ns PIC18FXXXX — 25 ns PIC18LFXXXX — 45 ns VDD = 2.0V VDD = 2.0V © 2008 Microchip Technology Inc. PIC18F2450/4450 FIGURE 21-11: EUSART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING RC6/TX/CK pin 121 121 RC7/RX/DT pin 120 Note: 122 Refer to Figure 21-4 for load conditions. TABLE 21-13: EUSART SYNCHRONOUS TRANSMISSION REQUIREMENTS Param No. 120 121 122 Symbol Characteristic TckH2dtV SYNC XMIT (MASTER & SLAVE) Clock High to Data Out Valid Tckrf Tdtrf FIGURE 21-12: Min Max Units PIC18FXXXX — 40 ns PIC18LFXXXX — 100 ns Clock Out Rise Time and Fall Time (Master mode) PIC18FXXXX — 20 ns PIC18LFXXXX — 50 ns Data Out Rise Time and Fall Time PIC18FXXXX — 20 ns PIC18LFXXXX — 50 ns Conditions VDD = 2.0V VDD = 2.0V VDD = 2.0V EUSART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING RC6/TX/CK pin 125 RC7/RX/DT pin 126 Note: Refer to Figure 21-4 for load conditions. TABLE 21-14: EUSART SYNCHRONOUS RECEIVE REQUIREMENTS Param. No. 125 126 Symbol Characteristic TDTV2CKL SYNC RCV (MASTER & SLAVE) Data Hold before CK ↓ (DT hold time) TCKL2DTL Data Hold after CK ↓ (DT hold time) © 2008 Microchip Technology Inc. Min Max Units 10 — ns 15 — ns Conditions DS39760D-page 291 PIC18F2450/4450 FIGURE 21-13: USB SIGNAL TIMING USB Data Differential Lines 90% VCRS 10% TLF, TFF TLR, TFR TABLE 21-15: USB LOW-SPEED TIMING REQUIREMENTS Param No. Symbol Characteristic Min Typ Max Units Conditions TLR Transition Rise Time 75 — 300 ns CL = 200 to 600 pF TLF Transition Fall Time 75 — 300 ns CL = 200 to 600 pF TLRFM Rise/Fall Time Matching 80 — 125 % Min Typ Max Units 4 — 20 ns CL = 50 pF CL = 50 pF TABLE 21-16: USB FULL-SPEED REQUIREMENTS Param No. Symbol Characteristic TFR Transition Rise Time TFF Transition Fall Time 4 — 20 ns TFRFM Rise/Fall Time Matching 90 — 111.1 % DS39760D-page 292 Conditions © 2008 Microchip Technology Inc. PIC18F2450/4450 TABLE 21-17: A/D CONVERTER CHARACTERISTICS: PIC18F2450/4450 (INDUSTRIAL) PIC18LF2450/4450 (INDUSTRIAL) Param Symbol No. Characteristic Min Typ Max Units — — 10 bit Conditions ΔVREF ≥ 3.0V A01 NR Resolution A03 EIL Integral Linearity Error — — <±1 LSb ΔVREF ≥ 3.0V A04 EDL Differential Linearity Error — — <±1 LSb ΔVREF ≥ 3.0V A06 EOFF Offset Error — — <±2 LSb ΔVREF ≥ 3.0V A07 EGN Gain Error — — <±1 LSb ΔVREF ≥ 3.0V A10 — Monotonicity — VSS ≤ VAIN ≤ VREF A20 ΔVREF Reference Voltage Range (VREFH – VREFL) 1.8 3 — — — — V V VDD < 3.0V VDD ≥ 3.0V A21 VREFH Reference Voltage High VSS — VREFH V A22 VREFL Reference Voltage Low VSS – 0.3V — VDD – 3.0V V A25 VAIN Analog Input Voltage VREFL — VREFH V A30 ZAIN Recommended Impedance of Analog Voltage Source — — 2.5 kΩ A50 IREF VREF Input Current(2) — — — — 5 150 μA μA Note 1: 2: Guaranteed(1) During VAIN acquisition. During A/D conversion cycle. The A/D conversion result never decreases with an increase in the input voltage and has no missing codes. VREFH current is from RA3/AN3/VREF+ pin or VDD, whichever is selected as the VREFH source. VREFL current is from RA2/AN2/VREF- pin or VSS, whichever is selected as the VREFL source. FIGURE 21-14: A/D CONVERSION TIMING BSF ADCON0, GO (Note 2) 131 Q4 A/D CLK 130 132 9 A/D DATA 8 7 ... ... OLD_DATA ADRES 2 1 0 NEW_DATA TCY(1) ADIF GO DONE SAMPLING STOPPED SAMPLE Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. 2: This is a minimal RC delay (typically 100 ns), which also disconnects the holding capacitor from the analog input. © 2008 Microchip Technology Inc. DS39760D-page 293 PIC18F2450/4450 TABLE 21-18: A/D CONVERSION REQUIREMENTS Param Symbol No. 130 TAD Characteristic A/D Clock Period Min Max Units 0.7 25(1) μs TOSC based, VREF ≥ 3.0V PIC18LFXXXX 1.4 (1) μs VDD = 2.0V, TOSC based, VREF full range PIC18FXXXX 2.0 6.0 μs A/D RC mode PIC18LFXXXX 3.0 9.0 μs VDD = 2.0V, A/D RC mode PIC18FXXXX 25 131 TCNV Conversion Time (not including acquisition time)(2) 11 12 TAD 132 TACQ Acquisition Time(3) 15 10 — — μs μs 135 TSWC Switching Time from Convert → Sample — (Note 4) 137 TDIS Discharge Time 0.2 — Note 1: 2: 3: 4: Conditions -40°C to +85°C 0°C ≤ to ≤ +85°C μs The time of the A/D clock period is dependent on the device frequency and the TAD clock divider. ADRES registers may be read on the following TCY cycle. The time for the holding capacitor to acquire the “New” input voltage when the voltage changes full scale after the conversion (VDD to VSS or VSS to VDD). The source impedance (RS) on the input channels is 50Ω. On the following cycle of the device clock. DS39760D-page 294 © 2008 Microchip Technology Inc. PIC18F2450/4450 22.0 PACKAGING INFORMATION 22.1 Package Marking Information 28-Lead SPDIP (Skinny DIP) Example PIC18F2450-I/SP e3 0810017 XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX YYWWNNN 28-Lead SOIC Example XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX YYWWNNN 28-Lead QFN Example XXXXXXXX XXXXXXXX YYWWNNN 18F2450 -I/ML e3 0810017 Legend: XX...X Y YY WW NNN e3 * Note: PIC18F2450-E/SO e3 0810017 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. © 2008 Microchip Technology Inc. DS39760D-page 295 PIC18F2450/4450 Package Marking Information (Continued) 40-Lead PDIP Example XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX YYWWNNN 44-Lead TQFP XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN 44-Lead QFN XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN DS39760D-page 296 PIC18F4450-I/P e3 0810017 Example PIC18F4450 -I/PT e3 0810017 Example PIC18F4450 -I/ML e3 0810017 © 2008 Microchip Technology Inc. PIC18F2450/4450 22.2 Package Details The following sections give the technical details of the packages. !" 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 N NOTE 1 E1 1 2 3 D E A2 A L c b1 A1 b e eB 6&! '! 9'&! 7"') %! 7,8. 7 7 7: ; < & & & = = ##44!! - 1!& & = = "#& "#>#& . - -- ##4>#& . < : 9& - -? & & 9 - 9#4!! < ) ) < 1 = = 69#>#& 9 *9#>#& : *+ 1, - !" !"#$%&"' ()"&'"!&) &#*&&&# +%&,&!& - '! !#.# &"#' #%! &"! ! #%! &"! !! &$#/!# '! #& .0 1,2 1!'! &$& "! **& "&& ! * ,1 © 2008 Microchip Technology Inc. DS39760D-page 297 PIC18F2450/4450 # #$%&'( #) !" 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D N E E1 NOTE 1 1 2 3 b e h α A2 A h c φ L A1 L1 6&! '! 9'&! 7"') %! β 99.. 7 7 7: ; < & : 8& = 1, = ##44!! = = &# %%+ = - : >#& . ##4>#& . 1, : 9& 1, ? -1, ,'%@ & A = 3 &9& 9 = 3 && 9 .3 3 & I B = <B 9#4!! < = -- 9#>#& ) - = #%& D B = B #%&1 && ' E B = B !" !"#$%&"' ()"&'"!&) &#*&&&# +%&,&!& - '! !#.# &"#' #%! &"! ! #%! &"! !! &$#''!# '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! * ,1 DS39760D-page 298 © 2008 Microchip Technology Inc. PIC18F2450/4450 *+%!,-./.*+! 01'((),1 !" 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D D2 EXPOSED PAD e E b E2 2 2 1 1 N K N NOTE 1 L BOTTOM VIEW TOP VIEW A A3 A1 6&! '! 9'&! 7"') %! 99.. 7 7 7: ; < & : 8& < &# %% , &&4!! - : >#& . .$ !##>#& . : 9& .$ !##9& ?1, .3 ?1, -? - ?1, -? - , &&>#& ) - - - , &&9& 9 , &&& .$ !## C = !" !"#$%&"' ()"&'"!&) &#*&&&# 4!!*!"&# - '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! = * ,1 © 2008 Microchip Technology Inc. DS39760D-page 299 PIC18F2450/4450 *+%!,-./.*+! 01'((),1 !" 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 DS39760D-page 300 © 2008 Microchip Technology Inc. PIC18F2450/4450 2. !" 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 N NOTE 1 E1 1 2 3 D E A2 A L c b1 A1 b e eB 6&! '! 9'&! 7"') %! 7,8. 7 7 7: ; & & & = = ##44!! = 1!& & = = "#& "#>#& . = ? ##4>#& . < = < : 9& < = & & 9 = 9#4!! < = ) - = ) = - 1 = = 69#>#& 9 *9#>#& : *+ 1, !" !"#$%&"' ()"&'"!&) &#*&&&# +%&,&!& - '! !#.# &"#' #%! &"! ! #%! &"! !! &$#/!# '! #& .0 1,2 1!'! &$& "! **& "&& ! * ,?1 © 2008 Microchip Technology Inc. DS39760D-page 301 PIC18F2450/4450 2231*+435/5/5%'3*+ !" 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D D1 E e E1 N b NOTE 1 1 2 3 NOTE 2 α A c φ β L A1 6&! '! 9'&! 7"') %9#! A2 L1 99.. 7 7 7: ; 9#& : 8& = <1, = ##44!! &# %% = 3 &9& 9 ? 3 && 9 .3 3 & I : >#& . B 1, -B : 9& 1, ##4>#& . 1, ##49& 1, B 9#4!! = 9#>#& ) - - #%& D B B -B #%&1 && ' E B B -B !" !"#$%&"' ()"&'"!&) &#*&&&# ,'%!& ! & D!E' - '! !#.# &"#' #%! &"! ! #%! &"! !! &$#''!# '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! * ,?1 DS39760D-page 302 © 2008 Microchip Technology Inc. PIC18F2450/4450 2231*+435/5/5%'3*+ !" 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 © 2008 Microchip Technology Inc. DS39760D-page 303 PIC18F2450/4450 22*+%!,-/*+! !" 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D D2 EXPOSED PAD e E E2 b 2 2 1 N 1 N NOTE 1 TOP VIEW K L BOTTOM VIEW A A3 A1 6&! '! 9'&! 7"') %! 99.. 7 7 7: ; & : 8& < &# %% , &&4!! - : >#& . .$ !##>#& . : 9& .$ !##9& ?1, .3 <1, ?- ? ?< <1, ?- ? , &&>#& ) - -< , &&9& 9 - , &&& .$ !## C = !" !"#$%&"' ()"&'"!&) &#*&&&# 4!!*!"&# - '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! ?< = * ,-1 DS39760D-page 304 © 2008 Microchip Technology Inc. PIC18F2450/4450 22*+%!,-/*+! !" 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 © 2008 Microchip Technology Inc. DS39760D-page 305 PIC18F2450/4450 NOTES: DS39760D-page 306 © 2008 Microchip Technology Inc. PIC18F2450/4450 APPENDIX A: REVISION HISTORY Revision A (January 2006) Original data sheet for PIC18F2450/4450 devices. Revision B (January 2007) Example 11-1 and Figure 14-1 have been updated, Section 14.5.1.1 “Bus Activity Detect Interrupt Bit (ACTVIF)” and Section 14.2.2.3 “Internal Pull-up Resistors” have been added, the Electrical Specifications in Section 21.0 “Electrical Characteristics” have been updated, the package diagrams in Section 22.2 “Package Details” have been updated and there have been minor corrections to the data sheet text. © 2008 Microchip Technology Inc. Revision C (August 2007) The Electrical Specifications in Section 21.2 “DC Characteristics: Power-Down and Supply Current” have been updated and the package diagrams in Section 22.2 “Package Details” have been updated. Revision D (March 2008) Minor edits to Section 14.0 “Universal Serial Bus (USB)”, Section 16.0 “10-Bit Analog-to-Digital Converter (A/D) Module”, Section 18.0 “Special Features of the CPU” and Section 21.0 “Electrical Characteristics”. DS39760D-page 307 PIC18F2450/4450 APPENDIX B: DEVICE DIFFERENCES The differences between the devices listed in this data sheet are shown in Table B-1. TABLE B-1: DEVICE DIFFERENCES Features PIC18F2450 PIC18F4450 Program Memory (Bytes) 16384 16384 Program Memory (Instructions) 8192 8192 13 13 Ports A, B, C, (E) Ports A, B, C, D, E 1 1 10 Input Channels 13 Input Channels 28-Pin SPDIP 28-Pin SOIC 28-Pin QFN 40-Pin PDIP 44-Pin TQFP 44-Pin QFN Interrupt Sources I/O Ports Capture/Compare/PWM Modules 10-Bit Analog-to-Digital Module Packages DS39760D-page 308 © 2008 Microchip Technology Inc. PIC18F2450/4450 APPENDIX C: CONVERSION CONSIDERATIONS This appendix discusses the considerations for converting from previous versions of a device to the ones listed in this data sheet. Typically, these changes are due to the differences in the process technology used. An example of this type of conversion is from a PIC16C74A to a PIC16C74B. Not Applicable © 2008 Microchip Technology Inc. APPENDIX D: MIGRATION FROM BASELINE TO ENHANCED DEVICES This section discusses how to migrate from a Baseline device (i.e., PIC16C5X) to an Enhanced MCU device (i.e., PIC18FXXX). The following are the list of modifications over the PIC16C5X microcontroller family: Not Currently Available DS39760D-page 309 PIC18F2450/4450 APPENDIX E: MIGRATION FROM MID-RANGE TO ENHANCED DEVICES A detailed discussion of the differences between the Mid-Range MCU devices (i.e., PIC16CXXX) and the Enhanced devices (i.e., PIC18FXXX) is provided in AN716, “Migrating Designs from PIC16C74A/74B to PIC18C442”. The changes discussed, while device specific, are generally applicable to all Mid-Range to Enhanced device migrations. APPENDIX F: MIGRATION FROM HIGH-END TO ENHANCED DEVICES A detailed discussion of the migration pathway and differences between the High-End MCU devices (i.e., PIC17CXXX) and the Enhanced devices (i.e., PIC18FXXX) is provided in AN726, “PIC17CXXX to PIC18CXXX Migration”. This Application Note is available as Literature Number DS00726. This Application Note is available as Literature Number DS00716. DS39760D-page 310 © 2008 Microchip Technology Inc. PIC18F2450/4450 INDEX A A/D ................................................................................... 175 Acquisition Requirements ........................................ 180 ADCON0 Register .................................................... 175 ADCON1 Register .................................................... 175 ADCON2 Register .................................................... 175 ADRESH Register ............................................ 175, 178 ADRESL Register .................................................... 175 Analog Port Pins, Configuring .................................. 182 Associated Registers ............................................... 184 Configuring the Module ............................................ 179 Conversion Clock (TAD) ........................................... 181 Conversion Requirements ....................................... 294 Conversion Status (GO/DONE Bit) .......................... 178 Conversions ............................................................. 183 Converter Characteristics ........................................ 293 Converter Interrupt, Configuring .............................. 179 Discharge ................................................................. 183 Operation in Power-Managed Modes ...................... 182 Selecting and Configuring Acquisition Time ............ 181 Special Event Trigger (CCP1) .................................. 184 Use of the CCP1 Trigger .......................................... 184 Absolute Maximum Ratings ............................................. 267 AC (Timing) Characteristics ............................................. 283 Load Conditions for Device Timing Specifications ................................................... 284 Parameter Symbology ............................................. 283 Temperature and Voltage Specifications ................. 284 Timing Conditions .................................................... 284 AC Characteristics Internal RC Accuracy ............................................... 286 ADCON0 Register ............................................................ 175 GO/DONE Bit ........................................................... 178 ADCON1 Register ............................................................ 175 ADCON2 Register ............................................................ 175 ADDFSR .......................................................................... 256 ADDLW ............................................................................ 219 ADDULNK ........................................................................ 256 ADDWF ............................................................................ 219 ADDWFC ......................................................................... 220 ADRESH Register ............................................................ 175 ADRESL Register .................................................... 175, 178 Analog-to-Digital Converter. See A/D. ANDLW ............................................................................ 220 ANDWF ............................................................................ 221 Assembler MPASM Assembler .................................................. 264 Auto-Wake-up on Sync Break Character ......................... 167 B BC .................................................................................... 221 BCF .................................................................................. 222 Block Diagrams A/D ........................................................................... 178 Analog Input Model .................................................. 179 Capture Mode Operation ......................................... 124 Compare Mode Operation ....................................... 125 Device Clock .............................................................. 24 EUSART Receive .................................................... 165 EUSART Transmit ................................................... 163 External Power-on Reset Circuit (Slow VDD Power-up) ......................................... 43 Fail-Safe Clock Monitor ............................................ 206 © 2008 Microchip Technology Inc. Generic I/O Port ......................................................... 99 High/Low-Voltage Detect with External Input .......... 186 Interrupt Logic ............................................................ 86 On-Chip Reset Circuit ................................................ 41 PIC18F2450 .............................................................. 10 PIC18F4450 .............................................................. 11 PLL (HS Mode) .......................................................... 26 PWM Operation (Simplified) .................................... 127 Reads from Flash Program Memory ......................... 77 Table Read Operation ............................................... 73 Table Write Operation ............................................... 74 Table Writes to Flash Program Memory .................... 79 Timer0 in 16-Bit Mode ............................................. 112 Timer0 in 8-Bit Mode ............................................... 112 Timer1 ..................................................................... 116 Timer1 (16-Bit Read/Write Mode) ............................ 116 Timer2 ..................................................................... 122 Typical External Transceiver with Isolation ............. 131 USB Interrupt Logic Funnel ..................................... 143 USB Peripheral and Options ................................... 129 USTAT FIFO ............................................................ 134 Watchdog Timer ...................................................... 203 BN .................................................................................... 222 BNC ................................................................................. 223 BNN ................................................................................. 223 BNOV .............................................................................. 224 BNZ ................................................................................. 224 BOR. See Brown-out Reset. BOV ................................................................................. 227 BRA ................................................................................. 225 Brown-out Reset (BOR) ..................................................... 44 Detecting ................................................................... 44 Disabling in Sleep Mode ............................................ 44 Software Enabled ...................................................... 44 BSF .................................................................................. 225 BTFSC ............................................................................. 226 BTFSS ............................................................................. 226 BTG ................................................................................. 227 BZ .................................................................................... 228 C C Compilers MPLAB C18 ............................................................. 264 MPLAB C30 ............................................................. 264 CALL ................................................................................ 228 CALLW ............................................................................ 257 Capture (CCP Module) .................................................... 124 Associated Registers ............................................... 126 CCP1 Pin Configuration .......................................... 124 CCPR1H:CCPR1L Registers .................................. 124 Prescaler ................................................................. 124 Software Interrupt .................................................... 124 Capture/Compare/PWM (CCP) ....................................... 123 Capture Mode. See Capture. CCP Mode and Timer Resources ............................ 124 CCPR1H Register ................................................... 124 CCPR1L Register .................................................... 124 Compare Mode. See Compare. Module Configuration .............................................. 124 Clock Sources .................................................................... 30 Selection Using OSCCON Register .......................... 30 CLRF ............................................................................... 229 CLRWDT ......................................................................... 229 DS39760D-page 311 PIC18F2450/4450 Code Examples 16 x 16 Signed Multiply Routine ................................ 84 16 x 16 Unsigned Multiply Routine ............................ 84 8 x 8 Signed Multiply Routine .................................... 83 8 x 8 Unsigned Multiply Routine ................................ 83 Changing Between Capture Prescalers ................... 124 Computed GOTO Using an Offset Value ................... 56 Erasing a Flash Program Memory Row ..................... 78 Fast Register Stack .................................................... 56 How to Clear RAM (Bank 1) Using Indirect Addressing ............................................ 67 Implementing a Real-Time Clock Using a Timer1 Interrupt Service ............................... 119 Initializing PORTA ...................................................... 99 Initializing PORTB .................................................... 101 Initializing PORTC .................................................... 104 Initializing PORTD .................................................... 107 Initializing PORTE .................................................... 109 Reading a Flash Program Memory Word .................. 77 Saving STATUS, WREG and BSR Registers in RAM ....................................... 97 Writing to Flash Program Memory ....................... 80–81 Code Protection ............................................................... 191 COMF ............................................................................... 230 Compare (CCP Module) ................................................... 125 Associated Registers ............................................... 126 CCP1 Pin Configuration ........................................... 125 CCPR1 Register ...................................................... 125 Software Interrupt .................................................... 125 Special Event Trigger ............................................... 125 Timer1 Mode Selection ............................................ 125 Configuration Bits ............................................................. 192 Configuration Register Protection .................................... 211 Context Saving During Interrupts ....................................... 97 Conversion Considerations .............................................. 309 CPFSEQ .......................................................................... 230 CPFSGT ........................................................................... 231 CPFSLT ........................................................................... 231 Crystal Oscillator/Ceramic Resonator ................................ 25 Customer Change Notification Service ............................ 319 Customer Notification Service .......................................... 319 Customer Support ............................................................ 319 D Data Addressing Modes ..................................................... 67 Comparing Addressing Modes with the Extended Instruction Set Enabled ................ 71 Direct .......................................................................... 67 Indexed Literal Offset ................................................. 70 BSR Operation ................................................... 72 Instructions Affected .......................................... 70 Mapping the Access Bank ................................. 72 Indirect ....................................................................... 67 Inherent and Literal .................................................... 67 Data Memory ...................................................................... 59 Access Bank .............................................................. 61 and the Extended Instruction Set ............................... 70 Bank Select Register (BSR) ....................................... 59 General Purpose Registers ........................................ 61 Map for PIC18F2450/4450 Devices ........................... 60 Special Function Registers ........................................ 62 Map .................................................................... 62 USB RAM ................................................................... 59 DS39760D-page 312 DAW ................................................................................ 232 DC Characteristics ........................................................... 278 Power-Down and Supply Current ............................ 270 Supply Voltage ........................................................ 269 DCFSNZ .......................................................................... 233 DECF ............................................................................... 232 DECFSZ .......................................................................... 233 Dedicated ICD/ICSP Port ................................................ 211 Demonstration, Development and Evaluation Boards ................................................... 266 Development Support ...................................................... 263 Device Differences ........................................................... 308 Device Overview .................................................................. 7 Features (table) ........................................................... 9 New Core Features ...................................................... 7 Other Special Features ................................................ 8 Direct Addressing .............................................................. 68 E Effect on Standard PIC MCU Instructions .............................................................. 260 Electrical Characteristics ................................................. 267 Enhanced Universal Synchronous Receiver Transmitter (USART). See EUSART. Equations A/D Acquisition Time ............................................... 180 A/D Minimum Charging Time ................................... 180 Calculating the Minimum Required A/D Acquisition Time ....................................... 180 Errata ................................................................................... 6 EUSART Asynchronous Mode ................................................ 163 Associated Registers, Receive ........................ 166 Associated Registers, Transmit ....................... 164 Auto-Wake-up on Sync Break ......................... 167 Break Character Sequence ............................. 168 Receiver .......................................................... 165 Receiving a Break Character ........................... 168 Setting Up 9-Bit Mode with Address Detect ........................................ 165 Transmitter ...................................................... 163 Baud Rate Generator (BRG) ................................... 157 Associated Registers ....................................... 158 Auto-Baud Rate Detect .................................... 161 Baud Rate Error, Calculating ........................... 158 Baud Rates, Asynchronous Modes ................. 159 High Baud Rate Select (BRGH Bit) ................. 157 Operation in Power-Managed Modes .............. 157 Sampling .......................................................... 157 Synchronous Master Mode ...................................... 169 Associated Registers, Receive ........................ 171 Associated Registers, Transmit ....................... 170 Reception ........................................................ 171 Transmission ................................................... 169 Synchronous Slave Mode ........................................ 172 Associated Registers, Receive ........................ 173 Associated Registers, Transmit ....................... 172 Reception ........................................................ 173 Transmission ................................................... 172 © 2008 Microchip Technology Inc. PIC18F2450/4450 Extended Instruction Set .................................................. 255 ADDFSR .................................................................. 256 ADDULNK ................................................................ 256 CALLW ..................................................................... 257 Considerations for Use ............................................ 260 MOVSF .................................................................... 257 MOVSS .................................................................... 258 PUSHL ..................................................................... 258 SUBFSR .................................................................. 259 SUBULNK ................................................................ 259 Syntax ...................................................................... 255 Use with MPLAB IDE Tools ..................................... 262 External Clock Input ........................................................... 26 F Fail-Safe Clock Monitor ............................................ 191, 206 Exiting Operation ..................................................... 206 Interrupts in Power-Managed Modes ....................... 207 POR or Wake-up From Sleep .................................. 207 WDT During Oscillator Failure ................................. 206 Fast Register Stack ............................................................ 56 Firmware Instructions ....................................................... 213 Flash Program Memory ..................................................... 73 Associated Registers ................................................. 81 Control Registers ....................................................... 74 EECON1 and EECON2 ..................................... 74 TABLAT (Table Latch) Register ......................... 76 TBLPTR (Table Pointer) Register ...................... 76 Erase Sequence ........................................................ 78 Erasing ....................................................................... 78 Operation During Code-Protect ................................. 81 Protection Against Spurious Writes ........................... 81 Reading ...................................................................... 77 Table Pointer Boundaries Based on Operation ........................ 76 Table Pointer Boundaries .......................................... 76 Table Reads and Table Writes .................................. 73 Unexpected Termination of Write .............................. 81 Write Sequence ......................................................... 79 Write Verify ................................................................ 81 Writing To ................................................................... 79 FSCM. See Fail-Safe Clock Monitor. G GOTO .............................................................................. 234 H Hardware Multiplier ............................................................ 83 Introduction ................................................................ 83 Operation ................................................................... 83 Performance Comparison .......................................... 83 High/Low-Voltage Detect ................................................. 185 Applications .............................................................. 188 Associated Registers ............................................... 189 Characteristics ......................................................... 282 Current Consumption ............................................... 187 Effects of a Reset ..................................................... 189 Operation ................................................................. 186 During Sleep .................................................... 189 Setup ........................................................................ 187 Start-up Time ........................................................... 187 Typical Application ................................................... 188 HLVD. See High/Low-Voltage Detect. © 2008 Microchip Technology Inc. I I/O Ports ............................................................................ 99 ID Locations ............................................................. 191, 211 Idle Modes ......................................................................... 37 INCF ................................................................................ 234 INCFSZ ............................................................................ 235 In-Circuit Debugger .......................................................... 211 In-Circuit Serial Programming (ICSP) ...................... 191, 211 Indexed Literal Offset Addressing and Standard PIC18 Instructions ............................. 260 Indexed Literal Offset Mode ............................................. 260 Indirect Addressing ............................................................ 68 INFSNZ ............................................................................ 235 Initialization Conditions for all Registers ...................... 49–52 Instruction Cycle ................................................................ 57 Clocking Scheme ....................................................... 57 Flow/Pipelining .......................................................... 57 Instruction Set .................................................................. 213 ADDLW .................................................................... 219 ADDWF ................................................................... 219 ADDWF (Indexed Literal Offset mode) .................... 261 ADDWFC ................................................................. 220 ANDLW .................................................................... 220 ANDWF ................................................................... 221 BC ............................................................................ 221 BCF ......................................................................... 222 BN ............................................................................ 222 BNC ......................................................................... 223 BNN ......................................................................... 223 BNOV ...................................................................... 224 BNZ ......................................................................... 224 BOV ......................................................................... 227 BRA ......................................................................... 225 BSF .......................................................................... 225 BSF (Indexed Literal Offset mode) .......................... 261 BTFSC ..................................................................... 226 BTFSS ..................................................................... 226 BTG ......................................................................... 227 BZ ............................................................................ 228 CALL ........................................................................ 228 CLRF ....................................................................... 229 CLRWDT ................................................................. 229 COMF ...................................................................... 230 CPFSEQ .................................................................. 230 CPFSGT .................................................................. 231 CPFSLT ................................................................... 231 DAW ........................................................................ 232 DCFSNZ .................................................................. 233 DECF ....................................................................... 232 DECFSZ .................................................................. 233 General Format ....................................................... 215 GOTO ...................................................................... 234 INCF ........................................................................ 234 INCFSZ .................................................................... 235 INFSNZ .................................................................... 235 IORLW ..................................................................... 236 IORWF ..................................................................... 236 LFSR ....................................................................... 237 MOVF ...................................................................... 237 MOVFF .................................................................... 238 MOVLB .................................................................... 238 MOVLW ................................................................... 239 DS39760D-page 313 PIC18F2450/4450 MOVWF ................................................................... 239 MULLW .................................................................... 240 MULWF .................................................................... 240 NEGF ....................................................................... 241 NOP ......................................................................... 241 Opcode Field Descriptions ....................................... 214 POP ......................................................................... 242 PUSH ....................................................................... 242 RCALL ..................................................................... 243 RESET ..................................................................... 243 RETFIE .................................................................... 244 RETLW .................................................................... 244 RETURN .................................................................. 245 RLCF ........................................................................ 245 RLNCF ..................................................................... 246 RRCF ....................................................................... 246 RRNCF .................................................................... 247 SETF ........................................................................ 247 SETF (Indexed Literal Offset mode) ........................ 261 SLEEP ..................................................................... 248 Standard Instructions ............................................... 213 SUBFWB .................................................................. 248 SUBLW .................................................................... 249 SUBWF .................................................................... 249 SUBWFB .................................................................. 250 SWAPF .................................................................... 250 TBLRD ..................................................................... 251 TBLWT ..................................................................... 252 TSTFSZ ................................................................... 253 XORLW .................................................................... 253 XORWF .................................................................... 254 INTCON Register RBIF Bit .................................................................... 101 INTCON Registers ............................................................. 87 Internal Oscillator Block INTHS, INTXT, INTCKO and INTIO Modes ............... 27 Internal RC Oscillator Use with WDT .......................................................... 203 Internet Address ............................................................... 319 Interrupt Sources .............................................................. 191 A/D Conversion Complete ....................................... 179 Capture Complete (CCP) ......................................... 124 Compare Complete (CCP) ....................................... 125 Interrupt-on-Change (RB7:RB4) .............................. 101 INTx Pin ..................................................................... 97 PORTB, Interrupt-on-Change .................................... 97 TMR0 ......................................................................... 97 TMR0 Overflow ........................................................ 113 TMR1 Overflow ........................................................ 115 TMR2 to PR2 Match (PWM) .................................... 127 Interrupts ............................................................................ 85 USB ............................................................................ 85 Interrupts, Flag Bits Interrupt-on-Change (RB7:RB4) Flag (RBIF Bit) ................................................. 101 INTOSC, INTRC. See Internal Oscillator Block. IORLW ............................................................................. 236 IORWF ............................................................................. 236 IPR Registers ..................................................................... 94 L LFSR ................................................................................ 237 Low-Voltage ICSP Programming. See Single-Supply ICSP Programming. DS39760D-page 314 M Master Clear Reset (MCLR) .............................................. 43 Memory Organization ........................................................ 53 Data Memory ............................................................. 59 Program Memory ....................................................... 53 Memory Programming Requirements .............................. 280 Microchip Internet Web Site ............................................. 319 Migration from Baseline to Enhanced Devices ................ 309 Migration from High-End to Enhanced Devices ............... 310 Migration from Mid-Range to Enhanced Devices ............ 310 MOVF .............................................................................. 237 MOVFF ............................................................................ 238 MOVLB ............................................................................ 238 MOVLW ........................................................................... 239 MOVSF ............................................................................ 257 MOVSS ............................................................................ 258 MOVWF ........................................................................... 239 MPLAB ASM30 Assembler, Linker, Librarian .................. 264 MPLAB ICD 2 In-Circuit Debugger .................................. 265 MPLAB ICE 2000 High-Performance Universal In-Circuit Emulator ................................... 265 MPLAB Integrated Development Environment Software ............................................. 263 MPLAB PM3 Device Programmer ................................... 265 MPLAB REAL ICE In-Circuit Emulator System ............... 265 MPLINK Object Linker/MPLIB Object Librarian ............... 264 MULLW ............................................................................ 240 MULWF ............................................................................ 240 N NEGF ............................................................................... 241 NOP ................................................................................. 241 O Oscillator Configuration ..................................................... 23 EC .............................................................................. 23 ECIO .......................................................................... 23 ECPIO ....................................................................... 23 ECPLL ....................................................................... 23 HS .............................................................................. 23 HSPLL ....................................................................... 23 INTCKO ..................................................................... 23 Internal Oscillator Block ............................................. 27 INTHS ........................................................................ 23 INTIO ......................................................................... 23 INTXT ........................................................................ 23 Oscillator Modes and USB Operation ........................ 24 XT .............................................................................. 23 XTPLL ........................................................................ 23 Oscillator Selection .......................................................... 191 Oscillator Settings for USB ................................................ 27 Oscillator Start-up Timer (OST) ................................... 32, 45 Oscillator Switching ........................................................... 30 Oscillator Transitions ......................................................... 30 Oscillator, Timer1 ............................................................. 115 P Packaging Information ..................................................... 295 Details ...................................................................... 297 Marking .................................................................... 295 PICkit 2 Development Programmer ................................. 266 PICSTART Plus Development Programmer .................... 266 PIE Registers ..................................................................... 92 © 2008 Microchip Technology Inc. PIC18F2450/4450 Pin Functions MCLR/VPP/RE3 .................................................... 12, 16 NC/ICCK/ICPGC ........................................................ 21 NC/ICDT/ICPGD ........................................................ 21 NC/ICPORTS ............................................................. 21 NC/ICRST/ICVPP ....................................................... 21 OSC1/CLKI .......................................................... 12, 16 OSC2/CLKO/RA6 ................................................ 12, 16 RA0/AN0 .............................................................. 13, 17 RA1/AN1 .............................................................. 13, 17 RA2/AN2/VREF- .................................................... 13, 17 RA3/AN3/VREF+ ................................................... 13, 17 RA4/T0CKI/RCV .................................................. 13, 17 RA5/AN4/HLVDIN ................................................ 13, 17 RB0/AN12/INT0 ................................................... 14, 18 RB1/AN10/INT1 ................................................... 14, 18 RB2/AN8/INT2/VMO ............................................ 14, 18 RB3/AN9/VPO ..................................................... 14, 18 RB4/AN11/KBI0 ................................................... 14, 18 RB5/KBI1/PGM .................................................... 14, 18 RB6/KBI2/PGC .................................................... 14, 18 RB7/KBI3/PGD .................................................... 14, 18 RC0/T1OSO/T1CKI ............................................. 15, 19 RC1/T1OSI/UOE .................................................. 15, 19 RC2/CCP1 ........................................................... 15, 19 RC4/D-/VM ........................................................... 15, 19 RC5/D+/VP .......................................................... 15, 19 RC6/TX/CK .......................................................... 15, 19 RC7/RX/DT .......................................................... 15, 19 RD0 ............................................................................ 20 RD1 ............................................................................ 20 RD2 ............................................................................ 20 RD3 ............................................................................ 20 RD4 ............................................................................ 20 RD5 ............................................................................ 20 RD6 ............................................................................ 20 RD7 ............................................................................ 20 RE0/AN5 .................................................................... 21 RE1/AN6 .................................................................... 21 RE2/AN7 .................................................................... 21 VDD ...................................................................... 15, 21 VSS ....................................................................... 15, 21 VUSB ..................................................................... 15, 21 Pinout I/O Descriptions PIC18F2450 ............................................................... 12 PIC18F4450 ............................................................... 16 PIR Registers ..................................................................... 90 PLL Frequency Multiplier ................................................... 26 HSPLL, XTPLL, ECPLL and ECPIO Oscillator Modes .................................... 26 PLL Lock Time-out ............................................................. 45 POP ................................................................................. 242 POR. See Power-on Reset. PORTA Associated Registers ............................................... 100 I/O Summary ............................................................ 100 LATA Register ............................................................ 99 PORTA Register ........................................................ 99 TRISA Register .......................................................... 99 © 2008 Microchip Technology Inc. PORTB Associated Registers ............................................... 103 I/O Summary ........................................................... 102 LATB Register ......................................................... 101 PORTB Register ...................................................... 101 RB7:RB4 Interrupt-on-Change Flag (RBIF Bit) ......................................................... 101 TRISB Register ........................................................ 101 PORTC Associated Registers ............................................... 106 I/O Summary ........................................................... 105 LATC Register ......................................................... 104 PORTC Register ...................................................... 104 TRISC Register ....................................................... 104 PORTD Associated Registers ............................................... 108 I/O Summary ........................................................... 108 LATD Register ......................................................... 107 PORTD Register ...................................................... 107 TRISD Register ....................................................... 107 PORTE Associated Registers ............................................... 110 I/O Summary ........................................................... 110 LATE Register ......................................................... 109 PORTE Register ...................................................... 109 TRISE Register ........................................................ 109 Postscaler, WDT Assignment (PSA Bit) .............................................. 113 Rate Select (T0PS2:T0PS0 Bits) ............................. 113 Power-Managed Modes ..................................................... 33 and A/D Operation ................................................... 182 Clock Sources ........................................................... 33 Clock Transitions and Status Indicators .................... 34 Effects on Various Clock Sources ............................. 32 Entering ..................................................................... 33 Exiting Idle and Sleep Modes .................................... 39 by Interrupt ........................................................ 39 by Reset ............................................................ 39 by WDT Time-out .............................................. 39 Without an Oscillator Start-up Delay ................. 40 Idle ............................................................................. 37 Idle Modes PRI_IDLE .......................................................... 38 RC_IDLE ........................................................... 39 SEC_IDLE ......................................................... 38 Multiple Sleep Commands ......................................... 34 Run Modes ................................................................ 34 PRI_RUN ........................................................... 34 RC_RUN ............................................................ 36 SEC_RUN ......................................................... 34 Selecting .................................................................... 33 Sleep ......................................................................... 37 Summary (table) ........................................................ 33 Power-on Reset (POR) ...................................................... 43 Power-up Delays ............................................................... 32 Power-up Timer (PWRT) ............................................. 32, 45 Prescaler, Timer0 ............................................................ 113 Assignment (PSA Bit) .............................................. 113 Rate Select (T0PS2:T0PS0 Bits) ............................. 113 Prescaler, Timer2 ............................................................ 128 DS39760D-page 315 PIC18F2450/4450 PRI_IDLE Mode ................................................................. 38 PRI_RUN Mode ................................................................. 34 Program Counter ................................................................ 54 PCL, PCH and PCU Registers ................................... 54 PCLATH and PCLATU Registers .............................. 54 Program Memory and the Extended Instruction Set ............................... 70 Code Protection ....................................................... 209 Instructions ................................................................. 58 Two-Word .......................................................... 58 Interrupt Vector .......................................................... 53 Look-up Tables .......................................................... 56 Map and Stack (diagram) ........................................... 53 Reset Vector .............................................................. 53 Program Verification and Code Protection ....................... 208 Associated Registers ............................................... 208 Programming, Device Instructions ................................... 213 Pulse-Width Modulation. See PWM (CCP Module). PUSH ............................................................................... 242 PUSH and POP Instructions .............................................. 55 PUSHL ............................................................................. 258 PWM (CCP Module) Associated Registers ............................................... 128 Duty Cycle ................................................................ 127 Example Frequencies/Resolutions .......................... 128 Period ....................................................................... 127 Setup for PWM Operation ........................................ 128 TMR2 to PR2 Match ................................................ 127 Q Q Clock ............................................................................ 128 R RAM. See Data Memory. RC_IDLE Mode .................................................................. 39 RC_RUN Mode .................................................................. 36 RCALL .............................................................................. 243 RCON Register Bit Status During Initialization .................................... 48 Reader Response ............................................................ 320 Register File Summary ................................................. 63–65 Registers ADCON0 (A/D Control 0) ......................................... 175 ADCON1 (A/D Control 1) ......................................... 176 ADCON2 (A/D Control 2) ......................................... 177 BAUDCON (Baud Rate Control) .............................. 156 BDnSTAT (Buffer Descriptor n Status, CPU Mode) ...................................................... 139 BDnSTAT (Buffer Descriptor n Status, SIE Mode) ........................................................ 140 CCP1CON (Capture/Compare/PWM Control) ......... 123 CONFIG1H (Configuration 1 High) .......................... 194 CONFIG1L (Configuration 1 Low) ............................ 193 CONFIG2H (Configuration 2 High) .......................... 196 CONFIG2L (Configuration 2 Low) ............................ 195 CONFIG3H (Configuration 3 High) .......................... 197 CONFIG4L (Configuration 4 Low) ............................ 198 CONFIG5H (Configuration 5 High) .......................... 199 CONFIG5L (Configuration 5 Low) ............................ 199 CONFIG6H (Configuration 6 High) .......................... 200 CONFIG6L (Configuration 6 Low) ............................ 200 CONFIG7H (Configuration 7 High) .......................... 201 CONFIG7L (Configuration 7 Low) ............................ 201 DEVID1 (Device ID 1) .............................................. 202 DEVID2 (Device ID 2) .............................................. 202 EECON1 (Memory Control 1) .................................... 75 DS39760D-page 316 HLVDCON (High/Low-Voltage Detect Control) ................................................ 185 INTCON (Interrupt Control) ........................................ 87 INTCON2 (Interrupt Control 2) ................................... 88 INTCON3 (Interrupt Control 3) ................................... 89 IPR1 (Peripheral Interrupt Priority 1) ......................... 94 IPR2 (Peripheral Interrupt Priority 2) ......................... 95 OSCCON (Oscillator Control) .................................... 31 PIE1 (Peripheral Interrupt Enable 1) .......................... 92 PIE2 (Peripheral Interrupt Enable 2) .......................... 93 PIR1 (Peripheral Interrupt Request (Flag) 1) ............. 90 PIR2 (Peripheral Interrupt Request (Flag) 2) ............. 91 PORTE .................................................................... 109 RCON (Reset Control) ......................................... 42, 96 RCSTA (Receive Status and Control) ..................... 155 STATUS .................................................................... 66 STKPTR (Stack Pointer) ............................................ 55 T0CON (Timer0 Control) ......................................... 111 T1CON (Timer1 Control) ......................................... 115 T2CON (Timer2 Control) ......................................... 121 TXSTA (Transmit Status and Control) ..................... 154 UCFG (USB Configuration) ..................................... 132 UCON (USB Control) ............................................... 130 UEIE (USB Error Interrupt Enable) .......................... 148 UEIR (USB Error Interrupt Status) ........................... 147 UEPn (USB Endpoint n Control) .............................. 135 UIE (USB Interrupt Enable) ..................................... 146 UIR (USB Interrupt Status) ...................................... 144 USTAT (USB Status) ............................................... 134 WDTCON (Watchdog Timer Control) ...................... 204 RESET ............................................................................. 243 Reset State of Registers .................................................... 48 Reset Timers ..................................................................... 45 Oscillator Start-up Timer (OST) ................................. 45 PLL Lock Time-out ..................................................... 45 Power-up Timer (PWRT) ........................................... 45 Resets ........................................................................ 41, 191 Brown-out Reset (BOR) ........................................... 191 Oscillator Start-up Timer (OST) ............................... 191 Power-on Reset (POR) ............................................ 191 Power-up Timer (PWRT) ......................................... 191 RETFIE ............................................................................ 244 RETLW ............................................................................ 244 RETURN .......................................................................... 245 Return Address Stack ........................................................ 54 and Associated Registers .......................................... 54 Return Stack Pointer (STKPTR) ........................................ 55 Revision History ............................................................... 307 RLCF ............................................................................... 245 RLNCF ............................................................................. 246 RRCF ............................................................................... 246 RRNCF ............................................................................ 247 S SEC_IDLE Mode ............................................................... 38 SEC_RUN Mode ................................................................ 34 SETF ................................................................................ 247 Single-Supply ICSP Programming ................................... 212 SLEEP ............................................................................. 248 Sleep OSC1 and OSC2 Pin States ...................................... 32 Sleep Mode ........................................................................ 37 Software Simulator (MPLAB SIM) ................................... 264 Special Event Trigger. See Compare (CCP Module). Special Features of the CPU ........................................... 191 Special ICPORT Features ............................................... 211 © 2008 Microchip Technology Inc. PIC18F2450/4450 Stack Full/Underflow Resets .............................................. 56 STATUS Register .............................................................. 66 SUBFSR .......................................................................... 259 SUBFWB .......................................................................... 248 SUBLW ............................................................................ 249 SUBULNK ........................................................................ 259 SUBWF ............................................................................ 249 SUBWFB .......................................................................... 250 SWAPF ............................................................................ 250 T T0CON Register PSA Bit ..................................................................... 113 T0CS Bit ................................................................... 112 T0PS2:T0PS0 Bits ................................................... 113 T0SE Bit ................................................................... 112 Table Pointer Operations (table) ........................................ 76 Table Reads/Table Writes ................................................. 56 TBLRD ............................................................................. 251 TBLWT ............................................................................. 252 Time-out in Various Situations (table) ................................ 45 Time-out Sequence ............................................................ 45 Timer0 .............................................................................. 111 16-Bit Mode Timer Reads and Writes ...................... 112 Associated Registers ............................................... 113 Clock Source Edge Select (T0SE Bit) ...................... 112 Clock Source Select (T0CS Bit) ............................... 112 Operation ................................................................. 112 Overflow Interrupt .................................................... 113 Prescaler .................................................................. 113 Switching Assignment ...................................... 113 Prescaler. See Prescaler, Timer0. Timer1 .............................................................................. 115 16-Bit Read/Write Mode ........................................... 117 Associated Registers ....................................... 120, 126 Interrupt .................................................................... 118 Operation ................................................................. 116 Oscillator .......................................................... 115, 117 Layout Considerations ..................................... 118 Low-Power Option ........................................... 117 Using Timer1 as a Clock Source ..................... 117 Overflow Interrupt .................................................... 115 Resetting, Using a Special Event Trigger Output (CCP) ....................................... 118 TMR1H Register ...................................................... 115 TMR1L Register ....................................................... 115 Use as a Real-Time Clock ....................................... 118 Timer2 .............................................................................. 121 Associated Registers ............................................... 122 Interrupt .................................................................... 122 Operation ................................................................. 121 Output ...................................................................... 122 PR2 Register ............................................................ 127 TMR2 to PR2 Match Interrupt .................................. 127 Timing Diagrams A/D Conversion ........................................................ 293 Asynchronous Reception ......................................... 166 Asynchronous Transmission .................................... 164 Asynchronous Transmission (Back-to-Back) ................................................. 164 Automatic Baud Rate Calculation ............................ 162 Auto-Wake-up Bit (WUE) During Normal Operation ............................................ 167 Auto-Wake-up Bit (WUE) During Sleep ................... 167 BRG Overflow Sequence ......................................... 162 Brown-out Reset (BOR) ........................................... 288 © 2008 Microchip Technology Inc. Capture/Compare/PWM (CCP) ............................... 290 CLKO and I/O .......................................................... 287 Clock/Instruction Cycle .............................................. 57 EUSART Synchronous Receive (Master/Slave) ................................................. 291 EUSART Synchronous Transmission (Master/Slave) ................................................. 291 External Clock (All Modes Except PLL) ................... 285 Fail-Safe Clock Monitor ........................................... 207 High/Low-Voltage Detect Characteristics ................ 282 High-Voltage Detect (VDIRMAG = 1) ...................... 188 Low-Voltage Detect (VDIRMAG = 0) ....................... 187 PWM Output ............................................................ 127 Reset, Watchdog Timer (WDT), Oscillator Start-up Timer (OST) and Power-up Timer (PWRT) ................................................. 288 Send Break Character Sequence ............................ 168 Slow Rise Time (MCLR Tied to VDD, VDD Rise > TPWRT) ............................................ 47 Synchronous Reception (Master Mode, SREN) ..................................... 171 Synchronous Transmission ..................................... 169 Synchronous Transmission (Through TXEN) .......... 170 Time-out Sequence on POR w/PLL Enabled (MCLR Tied to VDD) .......................................... 47 Time-out Sequence on Power-up (MCLR Not Tied to VDD), Case 1 ...................... 46 Time-out Sequence on Power-up (MCLR Not Tied to VDD), Case 2 ...................... 46 Time-out Sequence on Power-up (MCLR Tied to VDD, VDD Rise TPWRT) .............. 46 Timer0 and Timer1 External Clock .......................... 289 Transition for Entry to Idle Mode ............................... 38 Transition for Entry to SEC_RUN Mode .................... 35 Transition for Entry to Sleep Mode ............................ 37 Transition for Two-Speed Start-up (INTRC to HSPLL) ........................................... 205 Transition for Wake From Idle to Run Mode .............. 38 Transition for Wake From Sleep (HSPLL) ................. 37 Transition From RC_RUN Mode to PRI_RUN Mode ................................................. 36 Transition From SEC_RUN Mode to PRI_RUN Mode (HSPLL) .................................. 35 Transition to RC_RUN Mode ..................................... 36 USB Signal .............................................................. 292 Timing Diagrams and Specifications ............................... 285 Capture/Compare/PWM Requirements (CCP) ....................................... 290 CLKO and I/O Requirements ................................... 287 EUSART Synchronous Receive Requirements .................................................. 291 EUSART Synchronous Transmission Requirements .................................................. 291 External Clock Requirements .................................. 285 PLL Clock ................................................................ 286 Reset, Watchdog Timer, Oscillator Start-up Timer, Power-up Timer and Brown-out Reset Requirements ........................................ 288 Timer0 and Timer1 External Clock Requirements .................................................. 289 USB Full-Speed Requirements ............................... 292 USB Low-Speed Requirements ............................... 292 Top-of-Stack Access .......................................................... 54 TQFP Packages and Special Features ........................... 211 TSTFSZ ........................................................................... 253 DS39760D-page 317 PIC18F2450/4450 Two-Speed Start-up ................................................. 191, 205 Two-Word Instructions Example Cases .......................................................... 58 TXSTA Register BRGH Bit ................................................................. 157 Layered Framework ................................................. 151 Oscillator Requirements .......................................... 150 Output Enable Monitor ............................................. 133 Overview .......................................................... 129, 151 Ping-Pong Buffer Configuration ............................... 133 Power ...................................................................... 151 Power Modes ........................................................... 149 Bus Power Only ............................................... 149 Dual Power with Self-Power Dominance .............................................. 149 Self-Power Only ............................................... 149 Pull-up Resistors ...................................................... 133 RAM ......................................................................... 136 Memory Map .................................................... 136 Speed ...................................................................... 152 Status and Control ................................................... 130 Status Register (USTAT) ......................................... 134 Transfer Types ......................................................... 151 UFRMH:UFRML Registers ...................................... 136 U Universal Serial Bus ........................................................... 59 Address Register (UADDR) ..................................... 136 Associated Registers ............................................... 150 Buffer Descriptor Table ............................................ 137 Buffer Descriptors .................................................... 137 Address Validation ........................................... 140 Assignment in Different Buffering Modes ....................................... 142 BDnSTAT Register (CPU Mode) ..................... 138 BDnSTAT Register (SIE Mode) ....................... 140 Byte Count ....................................................... 140 Example ........................................................... 137 Memory Map .................................................... 141 Ownership ........................................................ 137 Ping-Pong Buffering ......................................... 141 Register Summary ........................................... 142 Status and Configuration ................................. 137 Class Specifications and Drivers ............................. 152 Descriptors ............................................................... 152 Endpoint Control ...................................................... 135 Enumeration ............................................................. 152 External Transceiver ................................................ 131 Eye Pattern Test Enable .......................................... 133 Firmware and Drivers ............................................... 150 Frame Number Registers ......................................... 136 Frames ..................................................................... 151 Internal Transceiver ................................................. 131 Internal Voltage Regulator ....................................... 133 Interrupts .................................................................. 143 and USB Transactions ..................................... 143 DS39760D-page 318 USB Internal Voltage Regulator Specifications ................ 281 Module Specifications .............................................. 281 USB. See Universal Serial Bus. W Watchdog Timer (WDT) ........................................... 191, 203 Associated Registers ............................................... 204 Control Register ....................................................... 203 During Oscillator Failure .......................................... 206 Programming Considerations .................................. 203 WWW Address ................................................................ 319 WWW, On-Line Support ...................................................... 6 X XORLW ............................................................................ 253 XORWF ........................................................................... 254 © 2008 Microchip Technology Inc. PIC18F2450/4450 THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: Users of Microchip products can receive assistance through several channels: • Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software • General Technical Support – Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing • Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives • • • • • Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://support.microchip.com CUSTOMER CHANGE NOTIFICATION SERVICE Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. © 2008 Microchip Technology Inc. DS39760D-page 319 PIC18F2450/4450 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. To: Technical Publications Manager RE: Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Device: PIC18F2450/4450 Y N Literature Number: DS39760D Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS39760D-page 320 © 2008 Microchip Technology Inc. PIC18F2450/4450 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X /XX XXX Device Temperature Range Package Pattern Examples: a) b) Device PIC18F2450(1), PIC18F4450(1), PIC18F2450T(2), PIC18F4450T(2); VDD range 4.2V to 5.5V PIC18LF2450(1), PIC18LF4450(1), PIC18LF2450T(2), PIC18LF4450T(2); VDD range 2.0V to 5.5V Temperature Range I E = = -40°C to +85°C (Industrial) -40°C to +125°C (Extended) Package PT SO SP P ML = = = = = TQFP (Thin Quad Flatpack) SOIC Skinny Plastic DIP PDIP QFN Pattern c) PIC18LF4450-I/P 301 = Industrial temp., PDIP package, Extended VDD limits, QTP pattern #301. PIC18LF2450-I/SO = Industrial temp., SOIC package, Extended VDD limits. PIC18F4450-I/P = Industrial temp., PDIP package, normal VDD limits. Note 1: 2: F = Standard Voltage Range LF = Wide Voltage Range T = in tape and reel TQFP packages only. QTP, SQTP, Code or Special Requirements (blank otherwise) © 2008 Microchip Technology Inc. DS39760D-page 321 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-4182-8400 Fax: 91-80-4182-8422 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 01/02/08 DS39760D-page 322 © 2008 Microchip Technology Inc.