MICROCHIP PIC18F63J90-I/PT

PIC18F85J90 Family
Data Sheet
64/80-Pin, High-Performance
Microcontrollers with LCD Driver
and nanoWatt Technology
© 2007 Microchip Technology Inc.
Preliminary
DS39770B
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, microID, MPLAB, PIC,
PICmicro, PICSTART, PRO MATE, PowerSmart, rfPIC, and
SmartShunt are registered trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
AmpLab, FilterLab, Linear Active Thermistor, Migratable
Memory, MXDEV, MXLAB, PS logo, SEEVAL, SmartSensor
and The Embedded Control Solutions Company are
registered trademarks of Microchip Technology Incorporated
in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, ECAN,
ECONOMONITOR, FanSense, FlexROM, fuzzyLAB,
In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi,
MPASM, MPLAB Certified logo, MPLIB, MPLINK, PICkit,
PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal,
PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB,
rfPICDEM, Select Mode, Smart Serial, SmartTel, Total
Endurance, UNI/O, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2007, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona, Gresham, Oregon and Mountain View, California. The
Company’s quality system processes and procedures are for its PIC®
MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial
EEPROMs, microperipherals, nonvolatile memory and analog
products. In addition, Microchip’s quality system for the design and
manufacture of development systems is ISO 9001:2000 certified.
DS39770B-page ii
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
64/80-Pin, High-Performance Microcontrollers with
LCD Driver and nanoWatt Technology
LCD Driver Module Features:
Low-Power Features:
• Direct LCD Panel Drive Capability:
- Can drive LCD panel while in Sleep mode
• Up to 48 Segments and 192 Pixels; Software
Selectable
• Programmable LCD Timing module:
- Multiple LCD timing sources available
- Up to 4 commons: static, 1/2, 1/3 or 1/4 multiplex
- Static, 1/2 or 1/3 Bias configuration
• Integrated Charge-Pump Module with Voltage
Boost
•
•
•
•
•
•
Peripheral Highlights:
Flexible Oscillator Structure:
• Two Crystal modes, 4-25 MHz
• Two External Clock modes, up to 40 MHz
• Internal Oscillator Block:
- 8 user-selectable frequencies from 31.25 kHz
to 8 MHz
• Secondary Oscillator using Timer1 @ 32 kHz
• Fail-Safe Clock Monitor:
- Allows for safe shutdown if peripheral clock fails
Flash # Single-Word
(bytes) Instructions
MSSP
I/O
LCD
(Pixels)
Timers
8/16-Bit
Device
SRAM
Data
Memory
(bytes)
CCP
SPI
Master
I2C™
10-Bit
A/D
(ch)
Comparators
• 1000 Erase/Write Cycle Flash Program Memory,
typical
• Flash Retention: 20 Years Minimum
• Self-Programmable under Software Control
• Priority Levels for Interrupts
• 8 x 8 Single-Cycle Hardware Multiplier
• Extended Watchdog Timer (WDT):
- Programmable period from 4 ms to 131s
• In-Circuit Serial Programming™ (ICSP™) via
two pins
• In-Circuit Debug with 3 Breakpoints via two pins
• Operating Voltage Range: 2.0V to 3.6V
• On-Chip 2.5V Regulator
EUSART/
AUSART
• High-Current Sink/Source: 25 mA/25 mA
(PORTB and PORTC)
• Sleep current as low as 100nA
• Up to Four External Interrupts
• Four 8-Bit/16-Bit Timer/Counter modules
- Uses Timer1
• Two Capture/Compare/PWM (CCP) modules:
- Capture is 16-bit, max. resolution 6.25 ns (TCY/16)
- Compare is 16-bit, max. resolution 100 ns (TCY)
- PWM output: PWM resolution is up to 10-bit
• Master Synchronous Serial Port (MSSP) module
with two modes of Operation:
- 3-wire/4-wire SPI (supports all 4 SPI modes)
- I2C™ Master and Slave mode
• One Addressable USART module
• One Enhanced USART module:
- Supports LIN 1.2
- Auto-wake-up on Start bit and Break character
- Auto-Baud Detect
• 10-Bit, up to 12-Channel A/D Converter:
- Auto-acquisition
- Conversion available during Sleep
• Two Analog Comparators
• Programmable Reference Voltage for
Comparators
Special Microcontroller Features:
Program Memory
Power-Managed modes: Run, Idle, Sleep
Run current down to 9 µA, typical
Idle current down to 2.5 µA, typical
Sleep current down to 0.1 µA, typical
Fast INTOSC startup from SLEEP
Two-Speed Oscillator Start-up reduces crystal
stabilization wait time
BOR/
LVD
PIC18F63J90
8K
4096
1024
51
132
1/3
2
Y
Y
1/1
12
2
Y
PIC18F64J90
16K
8192
1024
51
132
1/3
2
Y
Y
1/1
12
2
Y
PIC18F65J90
32K
16384
2048
51
132
1/3
2
Y
Y
1/1
12
2
Y
PIC18F83J90
8K
4096
1024
67
192
1/3
2
Y
Y
1/1
12
2
Y
PIC18F84J90
16K
8192
1024
67
192
1/3
2
Y
Y
1/1
12
2
Y
PIC18F85J90
32K
16384
2048
67
192
1/3
2
Y
Y
1/1
12
2
Y
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 1
PIC18F85J90 FAMILY
Pin Diagrams
RD7/SEG7
RD6/SEG6
RD5/SEG5
RD4/SEG4
RD3/SEG3
RD2/SEG2
RD1/SEG1
VDD
VSS
RD0/SEG0
RE7/CCP2(1)/SEG31
RE6/COM3
RE5/COM2
RE4/COM1
RE3/COM0
LCDBIAS3
64-Pin TQFP
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
RE1/LCDBIAS2
RE0/LCDBIAS1
1
48
47
RF7/AN5/SS/SEG25
RF6/AN11/SEG24
RF5/AN10/CVREF/SEG23
RF4/AN9/SEG22
2
3
4
5
6
7
8
9
10
11
12
13
14
RF3/AN8/SEG21
RF2/AN7/C1OUT/SEG20
15
16
RG0/LCDBIAS0
RG1/TX2/CK2
RG2/RX2/DT2/VLCAP1
RG3/VLCAP2
MCLR
RG4/SEG26
VSS
VDDCORE/VCAP
46
45
44
43
42
PIC18F63J90
41
40
PIC18F64J90
PIC18F65J90
39
38
37
36
35
34
33
RB0/INT0/SEG30
RB1/INT1/SEG8
RB2/INT2/SEG9
RB3/INT3/SEG10
RB4/KBI0/SEG11
RB5/KBI1/SEG29
RB6/KBI2/PGC
VSS
OSC2/CLKO/RA6
OSC1/CLKI/RA7
VDD
RB7/KBI3/PGD
RC5/SDO/SEG12
RC4/SDI/SDA/SEG16
RC3/SCK/SCL/SEG17
RC2/CCP1/SEG13
Note 1:
RC7/RX1/DT1/SEG28
RC6/TX1/CK1/SEG27
RC0/T1OSO/T13CKI
RA4/T0CKI/SEG14
RC1/T1OSI/CCP2(1)/SEG32
VDD
RA5/AN4/SEG15
VSS
RA0/AN0
RA1/AN1/SEG18
RA2/AN2/VREF-
AVSS
RA3/AN3/VREF+
AVDD
ENVREG
RF1/AN6/C2OUT/SEG19
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
The CCP2 pin placement depends on the CCP2MX bit setting.
DS39770B-page 2
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
Pin Diagrams (Continued)
RJ1/SEG33
RJ0
RD7/SEG7
RD6/SEG6
RD5/SEG5
RD4/SEG4
RD3/SEG3
RD2/SEG2
RD1/SEG1
VDD
VSS
RE7/CCP2(1)/SEG31
RD0/SEG0
RE6/COM3
RE5/COM2
RE4/COM1
RE3/COM0
LCDBIAS3
RH0/SEG47
RH1/SEG46
80-Pin TQFP
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
RH2/SEG45
RH3/SEG44
RE1/LCDBIAS2
RE0/LCDBIAS1
RG0/LCDBIAS0
RG1/TX2/CK2
RG2/RX2/DT2/VLCAP1
RG3/VLCAP2
MCLR
RG4/SEG26
VSS
VDDCORE/VCAP
1
60
59
2
3
58
57
4
5
6
7
8
9
56
55
54
53
52
PIC18F83J90
PIC18F84J90
PIC18F85J90
10
11
12
51
50
49
RF7/AN5/SS/SEG25
RF6/AN11/SEG24
RF5/AN10/CVREF/SEG23
RF4/AN9/SEG22
13
14
15
48
47
46
16
RF3/AN8/SEG21
RF2/AN7/C1OUT/SEG20
RH7/SEG43
17
18
45
44
RH6/SEG42
19
20
RJ2/SEG34
RJ3/SEG35
RB0/INT0/SEG30
RB1/INT1/SEG8
RB2/INT2/SEG9
RB3/INT3/SEG10
RB4/KBI0/SEG11
RB5/KBI1/SEG29
RB6/KBI2/PGC
VSS
OSC2/CLKO/RA6
OSC1/CLKI/RA7
VDD
RB7/KBI3/PGD
RC5/SDO/SEG12
43
42
RC4/SDI/SDA/SEG16
RC3/SCK/SCL/SEG17
RC2/CCP1/SEG13
RJ7/SEG36
41
RJ6/SEG37
Note 1:
RJ5/SEG38
RJ4/SEG39
RC7/RX1/DT1/SEG28
RC6/TX1/CK1/SEG27
RC0/T1OSO/T13CKI
RA4/T0CKI/SEG14
RC1/T1OSI/CCP2(1)I/SEG32
VDD
RA5/AN4/SEG15
VSS
RA0/AN0
RA1/AN1/SEG18
RA2/AN2/VREF-
AVSS
RA3/AN3/VREF+
AVDD
ENVREG
RF1/AN6/C2OUT/SEG19
RH4/SEG40
RH5/SEG41
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
The CCP2 pin placement depends on the CCP2MX bit setting.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 3
PIC18F85J90 FAMILY
Table of Contents
1.0 Device Overview .......................................................................................................................................................................... 7
2.0 Oscillator Configurations ............................................................................................................................................................ 29
3.0 Power-Managed Modes ............................................................................................................................................................. 37
4.0 Reset .......................................................................................................................................................................................... 45
5.0 Memory Organization ................................................................................................................................................................. 57
6.0 Flash Program Memory .............................................................................................................................................................. 81
7.0 8 x 8 Hardware Multiplier............................................................................................................................................................ 91
8.0 Interrupts .................................................................................................................................................................................... 93
9.0 I/O Ports ................................................................................................................................................................................... 109
10.0 Timer0 Module ......................................................................................................................................................................... 131
11.0 Timer1 Module ......................................................................................................................................................................... 135
12.0 Timer2 Module ......................................................................................................................................................................... 141
13.0 Timer3 Module ......................................................................................................................................................................... 143
14.0 Capture/Compare/PWM (CCP) Modules ................................................................................................................................. 147
15.0 Liquid Crystal Display (LCD) Driver Module ............................................................................................................................. 157
16.0 Master Synchronous Serial Port (MSSP) Module .................................................................................................................... 185
17.0 Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) ............................................................... 229
18.0 Addressable Universal Synchronous Asynchronous Receiver Transmitter (AUSART) ........................................................... 249
19.0 10-bit Analog-to-Digital Converter (A/D) Module ...................................................................................................................... 263
20.0 Comparator Module.................................................................................................................................................................. 273
21.0 Comparator Voltage Reference Module ................................................................................................................................... 279
22.0 Special Features of the CPU .................................................................................................................................................... 283
23.0 Instruction Set Summary .......................................................................................................................................................... 295
24.0 Development Support............................................................................................................................................................... 345
25.0 Electrical Characteristics .......................................................................................................................................................... 349
26.0 DC and AC Characteristics Graphs and Tables ....................................................................................................................... 387
27.0 Packaging Information.............................................................................................................................................................. 389
Appendix A: Revision History............................................................................................................................................................. 393
Appendix B: Migration Between High-End Device Families............................................................................................................... 393
Index .................................................................................................................................................................................................. 397
The Microchip Web Site ..................................................................................................................................................................... 407
Customer Change Notification Service .............................................................................................................................................. 407
Customer Support .............................................................................................................................................................................. 407
Reader Response .............................................................................................................................................................................. 408
Product Identification System............................................................................................................................................................. 409
DS39770B-page 4
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at [email protected] or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We
welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are
using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 5
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 6
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
1.0
DEVICE OVERVIEW
This document contains device specific information for
the following devices:
• PIC18F63J90
• PIC18F64J90
• PIC18F65J90
• PIC18F83J90
• PIC18F84J90
• PIC18F85J90
This family combines the traditional advantages of all
PIC18 microcontrollers – namely, high computational
performance and a rich feature set – with a versatile
on-chip LCD driver, while maintaining an extremely
competitive price point. These features make the
PIC18F85J90 family a logical choice for many
high-performance applications where price is a primary
consideration.
1.1
1.1.1
Core Features
nanoWatt TECHNOLOGY
All of the devices in the PIC18F85J90 family incorporate
a range of features that can significantly reduce power
consumption during operation. Key items include:
• Alternate Run Modes: By clocking the controller
from the Timer1 source or the internal RC
oscillator, power consumption during code
execution can be reduced by as much as 90%.
• Multiple Idle Modes: The controller can also run
with its CPU core disabled but the peripherals still
active. In these states, power consumption can be
reduced even further, to as little as 4% of normal
operation requirements.
• On-the-Fly Mode Switching: The power-managed
modes are invoked by user code during operation,
allowing the user to incorporate power-saving ideas
into their application’s software design.
1.1.2
OSCILLATOR OPTIONS AND
FEATURES
All of the devices in the PIC18F85J90 family offer six
different oscillator options, allowing users a range of
choices in developing application hardware. These
include:
• Two Crystal modes, using crystals or ceramic
resonators.
• Two External Clock modes, offering the option of
a divide-by-4 clock output.
• A Phase Lock Loop (PLL) frequency multiplier,
available to the External Oscillator modes which
allows clock speeds of up to 40 MHz.
• An internal oscillator block which provides an
8 MHz clock (±2% accuracy) and an INTRC source
(approximately 31 kHz, stable over temperature
and VDD), as well as a range of six user-selectable
clock frequencies, between 125 kHz to 4 MHz, for a
total of eight clock frequencies. This option frees the
two oscillator pins for use as additional general
purpose I/O.
© 2007 Microchip Technology Inc.
The internal oscillator block provides a stable reference
source that gives the family additional features for
robust operation:
• Fail-Safe Clock Monitor: This option constantly
monitors the main clock source against a reference
signal provided by the internal oscillator. If a clock
failure occurs, the controller is switched to the
internal oscillator, allowing for continued low-speed
operation or a safe application shutdown.
• Two-Speed Start-up: This option allows the
internal oscillator to serve as the clock source
from Power-on Reset, or wake-up from Sleep
mode, until the primary clock source is available.
1.1.3
MEMORY OPTIONS
The PIC18F85J90 family provides a range of program
memory options, from 8 Kbytes to 32 Kbytes of code
space. The Flash cells for program memory are rated
to last up to 1000 erase/write cycles. Data retention
without refresh is conservatively estimated to be
greater than 20 years.
The PIC18F85J90 family also provides plenty of room
for dynamic application data, with up to 2048 bytes of
data RAM.
1.1.4
EXTENDED INSTRUCTION SET
The PIC18F85J90 family implements the optional
extension to the PIC18 instruction set, adding 8 new
instructions and an Indexed Addressing mode.
Enabled as a device configuration option, the extension
has been specifically designed to optimize re-entrant
application code originally developed in high-level
languages, such as ‘C’.
1.1.5
EASY MIGRATION
Regardless of the memory size, all devices share the
same rich set of peripherals, allowing for a smooth
migration path as applications grow and evolve.
The consistent pinout scheme used throughout the
entire family also aids in migrating to the next larger
device. This is true when moving between the 64-pin
members, between the 80-pin members, or even
jumping from 64-pin to 80-pin devices.
The PIC18F85J90 family is also largely pin compatible
with other PIC18 families, such as the PIC18F8720 and
PIC18F8722, as well as the PIC18F8490 family of
microcontrollers with LCD drivers. This allows a new
dimension to the evolution of applications, allowing
developers to select different price points within
Microchip’s PIC18 portfolio, while maintaining a similar
feature set.
Preliminary
DS39770B-page 7
PIC18F85J90 FAMILY
1.2
LCD Driver
1.4
Details on Individual Family
Members
The on-chip LCD driver includes many features that
make the integration of displays in low-power
applications easier. These include an integrated voltage regulator with charge pump that allows contrast
control in software and display operation above device
VDD.
Devices in the PIC18F85J90 family are available in
64-pin and 80-pin packages. Block diagrams for the
two groups are shown in Figure 1-1 and Figure 1-2.
1.3
1.
Other Special Features
• Communications: The PIC18F85J90 family
incorporates a range of serial communication
peripherals, including an Addressable USART, a
separate Enhanced USART that supports LIN
specification 1.2, and one Master SSP module
capable of both SPI and I2C™ (Master and Slave)
modes of operation.
• CCP Modules: All devices in the family incorporate
two Capture/Compare/PWM (CCP) modules. Up to
four different time bases may be used to perform
several different operations at once.
• 10-Bit A/D Converter: This module incorporates
programmable acquisition time, allowing for a
channel to be selected and a conversion to be
initiated without waiting for a sampling period and
thus, reducing code overhead.
• Extended Watchdog Timer (WDT): This
enhanced version incorporates a 16-bit prescaler,
allowing an extended time-out range that is stable
across operating voltage and temperature. See
Section 25.0 “Electrical Characteristics” for
time-out periods.
DS39770B-page 8
The devices are differentiated from each other in four
ways:
2.
3.
4.
Flash program memory (three sizes, ranging
from 8 Kbytes for PIC18FX3J90 devices to
32 Kbytes for PIC18FX5J90 devices).
Data RAM (1024 bytes for PIC18FX3J90 and
PIC18FX4J90 devices, 2048 bytes for
PIC18FX5J90 devices).
I/O ports (7 bidirectional ports on 64-pin devices,
9 bidirectional ports on 80-pin devices).
LCD Pixels: 132 pixels (33 SEGs x 4 COMs) can
be driven by 64-pin devices; 192 pixels
(48 SEGs x 4 COMs) can be driven by 80-pin
devices.
All other features for devices in this family are identical.
These are summarized in Table 1-1 and Table 1-2.
The pinouts for all devices are listed in Table 1-3 and
Table 1-4.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 1-1:
DEVICE FEATURES FOR THE PIC18F85J90 FAMILY (64-PIN DEVICES)
Features
PIC18F63J90
PIC18F64J90
Operating Frequency
Program Memory (Bytes)
PIC18F65J90
DC – 40 MHz
8K
16K
32K
Program Memory (Instructions)
4096
8192
16384
Data Memory (Bytes)
1024
1024
2048
Interrupt Sources
27
I/O Ports
Ports A, B, C, D, E, F, G
LCD Driver (available pixels to drive)
132 (33 SEGs x 4 COMs)
Timers
4
Capture/Compare/PWM Modules
2
Serial Communications
MSSP, Addressable USART, Enhanced USART
10-bit Analog-to-Digital Module
Resets (and Delays)
Instruction Set
12 Input Channels
POR, BOR, RESET Instruction, Stack Full, Stack Underflow, MCLR, WDT
(PWRT, OST)
75 Instructions, 83 with Extended Instruction Set enabled
Packages
64-pin TQFP
TABLE 1-2:
DEVICE FEATURES FOR THE PIC18F85J90 FAMILY (80-PIN DEVICES)
Features
PIC18F83J90
PIC18F84J90
Operating Frequency
Program Memory (Bytes)
PIC18F85J90
DC – 40 MHz
8K
16K
32K
Program Memory (Instructions)
4096
8192
16384
Data Memory (Bytes)
1024
1024
2048
Interrupt Sources
I/O Ports
27
Ports A, B, C, D, E, F, G, H, J
LCD Driver (available pixels to drive)
192 (48 SEGs x 4 COMs)
Timers
4
Capture/Compare/PWM Modules
2
Serial Communications
MSSP, Addressable USART, Enhanced USART
10-bit Analog-to-Digital Module
Resets (and Delays)
Instruction Set
12 Input Channels
POR, BOR, RESET Instruction, Stack Full, Stack Underflow, MCLR, WDT
(PWRT, OST)
75 Instructions, 83 with Extended Instruction Set enabled
Packages
© 2007 Microchip Technology Inc.
80-pin TQFP
Preliminary
DS39770B-page 9
PIC18F85J90 FAMILY
FIGURE 1-1:
PIC18F6XJ90 (64-PIN) BLOCK DIAGRAM
Data Bus<8>
Table Pointer<21>
RA0:RA7(1,2)
Data Memory
(2.0, 3.9
Kbytes)
PCLATU PCLATH
21
PORTA
Data Latch
8
8
inc/dec logic
Address Latch
20
PCU PCH PCL
Program Counter
12
Data Address<12>
PORTB
RB0:RB7(1)
31 Level Stack
4
BSR
Address Latch
Program Memory
(96 Kbytes)
STKPTR
4
Access
Bank
12
FSR0
FSR1
FSR2
Data Latch
12
PORTC
RC0:RC7(1)
inc/dec
logic
8
Table Latch
Address
Decode
ROM Latch
Instruction Bus <16>
PORTD
RD0:RD7(1)
IR
8
Instruction
Decode and
Control
OSC2/CLKO
OSC1/CLKI
Power-up
Timer
INTRC
Oscillator
8 MHz
Oscillator
Oscillator
Start-up Timer
ENVREG
Voltage
Regulator
PORTE
RE0:RE1,
RE3:RE7(1)
PRODH PRODL
3
Timing
Generation
Precision
Band Gap
Reference
State Machine
Control Signals
8 x 8 Multiply
8
BITOP
W
8
8
8
8
Power-on
Reset
PORTF
8
RF1:RF7(1)
ALU<8>
Watchdog
Timer
8
BOR and
LVD(3)
PORTG
RG0:RG4(1)
VDDCORE/VCAP
Note 1:
VDD, VSS
MCLR
Timer0
Timer1
Timer2
Timer3
ADC
10-bit
Comparators
CCP1
CCP2
AUSART
EUSART
MSSP
LCD
Driver
See Table 1-3 for I/O port pin descriptions.
2:
RA6 and RA7 are only available as digital I/O in select oscillator modes. See Section 2.0 “Oscillator Configurations” for more
information
3:
Brown-out Reset and Low-Voltage Detect functions are provided when the on-board voltage regulator is enabled.
DS39770B-page 10
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 1-2:
PIC18F8XJ90 (80-PIN) BLOCK DIAGRAM
Data Bus<8>
Table Pointer<21>
RA0:RA7(1,2)
Data Memory
(2.0, 3.9
Kbytes)
PCLATU PCLATH
21
PORTA
Data Latch
8
8
inc/dec logic
Address Latch
20
PCU PCH PCL
Program Counter
PORTB
RB0:RB7(1)
12
Data Address<12>
31 Level Stack
4
BSR
Address Latch
Program Memory
(96 Kbytes)
STKPTR
4
Access
Bank
12
FSR0
FSR1
FSR2
Data Latch
PORTC
RC0:RC7(1)
12
inc/dec
logic
8
Table Latch
PORTD
RD0:RD7(1)
Address
Decode
ROM Latch
Instruction Bus <16>
PORTE
RE0:RE1,
RE3:RE7(1)
IR
8
Instruction
Decode and
Control
OSC2/CLKO
OSC1/CLKI
PORTF
PRODH PRODL
3
Timing
Generation
Power-up
Timer
INTRC
Oscillator
8 MHz
Oscillator
Oscillator
Start-up Timer
Watchdog
Timer
Voltage
Regulator
BOR and
LVD(3)
RF1:RF7(1)
8 x 8 Multiply
8
BITOP
W
8
8
8
PORTG
RG0:RG4(1)
8
Power-on
Reset
Precision
Band Gap
Reference
ENVREG
State Machine
Control Signals
8
ALU<8>
PORTH
RH0:RH7(1)
8
PORTJ
VDDCORE/VCAP
Note 1:
VDD,VSS
RJ0:RJ7(1)
MCLR
Timer0
Timer1
Timer2
Timer3
ADC
10-bit
Comparators
CCP1
CCP2
AUSART
EUSART
MSSP
LCD
Driver
See Table 1-3 for I/O port pin descriptions.
2:
RA6 and RA7 are only available as digital I/O in select oscillator modes. See Section 2.0 “Oscillator Configurations” for
more information.
3:
Brown-out Reset and Low-Voltage Detect functions are provided when the on-board voltage regulator is enabled.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 11
PIC18F85J90 FAMILY
TABLE 1-3:
PIC18F6XJ90 PINOUT I/O DESCRIPTIONS
Pin Number
Pin Name
TQFP
MCLR
7
OSC1/CLKI/RA7
OSC1
CLKI
39
Pin Buffer
Type Type
I
ST
I
I
CMOS
CMOS
I/O
TTL
O
—
CLKO
O
—
RA6
I/O
TTL
RA7
OSC2/CLKO/RA6
OSC2
40
Description
Master Clear (input) or programming voltage (input). This
pin is an active-low Reset to the device.
Oscillator crystal or external clock input.
Oscillator crystal input.
External clock source input. Always associated
with pin function OSC1. (See related OSC1/CLKI,
OSC2/CLKO pins.)
General purpose I/O pin.
Oscillator crystal or clock output.
Oscillator crystal output. Connects to crystal or
resonator in Crystal Oscillator mode.
In EC modes, OSC2 pin outputs CLKO, which has
1/4 the frequency of OSC1 and denotes the
instruction cycle rate.
General purpose I/O pin.
PORTA is a bidirectional I/O port.
RA0/AN0
RA0
AN0
24
RA1/AN1/SEG18
RA1
AN1
SEG18
23
RA2/AN2/VREFRA2
AN2
VREF-
22
RA3/AN3/VREF+
RA3
AN3
VREF+
21
RA4/T0CKI/SEG14
RA4
T0CKI
SEG14
28
RA5/AN4/SEG15
RA5
AN4
SEG15
27
I/O
I
TTL
Analog
Digital I/O.
Analog input 0.
I/O
I
O
TTL
Analog
Analog
Digital I/O.
Analog input 1.
SEG18 output for LCD.
I/O
I
I
TTL
Analog
Analog
Digital I/O.
Analog input 2.
A/D reference voltage (Low) input.
I/O
I
I
TTL
Analog
Analog
Digital I/O.
Analog input 3.
A/D reference voltage (High) input.
I/O
I
O
ST/OD
ST
Analog
Digital I/O. Open-drain when configured as output.
Timer0 external clock input.
SEG14 output for LCD.
I/O
I
O
TTL
Analog
Analog
Digital I/O.
Analog input 4.
SEG15 output for LCD.
RA6
See the OSC2/CLKO/RA6 pin.
RA7
See the OSC1/CLKI/RA7 pin.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
DS39770B-page 12
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 1-3:
PIC18F6XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTB is a bidirectional I/O port. PORTB can be software
programmed for internal weak pull-ups on all inputs.
RB0/INT0/SEG30
RB0
INT0
SEG30
48
RB1/INT1/SEG8
RB1
INT1
SEG8
47
RB2/INT2/SEG9
RB2
INT2
SEG9
46
RB3/INT3/SEG10
RB3
INT3
SEG10
45
RB4/KBI0/SEG11
RB4
KBI0
SEG11
44
RB5/KBI1/SEG29
RB5
KBI1
SEG29
43
RB6/KBI2/PGC
RB6
KBI2
PGC
42
RB7/KBI3/PGD
RB7
KBI3
PGD
37
I/O
I
O
TTL
ST
Analog
Digital I/O.
External interrupt 0.
SEG30 output for LCD.
I/O
I
O
TTL
ST
Analog
Digital I/O.
External interrupt 1.
SEG8 output for LCD.
I/O
I
O
TTL
ST
Analog
Digital I/O.
External interrupt 2.
SEG9 output for LCD.
I/O
I
O
TTL
ST
Analog
Digital I/O.
External interrupt 3.
SEG10 output for LCD.
I/O
I
O
TTL
TTL
Analog
Digital I/O.
Interrupt-on-change pin.
SEG11 output for LCD.
I/O
I
O
TTL
TTL
Analog
Digital I/O.
Interrupt-on-change pin.
SEG29 output for LCD.
I/O
I
I/O
TTL
TTL
ST
Digital I/O.
Interrupt-on-change pin.
In-Circuit Debugger and ICSP™ programming clock pin.
I/O
I
I/O
TTL
TTL
ST
Digital I/O.
Interrupt-on-change pin.
In-Circuit Debugger and ICSP programming data pin.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 13
PIC18F85J90 FAMILY
TABLE 1-3:
PIC18F6XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTC is a bidirectional I/O port.
RC0/T1OSO/T13CKI
RC0
T1OSO
T13CKI
30
RC1/T1OSI/CCP2/SEG32
RC1
T1OSI
CCP2(1)
SEG32
29
RC2/CCP1/SEG13
RC2
CCP1
SEG13
33
RC3/SCK/SCL/SEG17
RC3
SCK
SCL
SEG17
34
RC4/SDI/SDA/SEG16
RC4
SDI
SDA
SEG16
35
RC5/SDO/SEG12
RC5
SDO
SEG12
36
RC6/TX1/CK1/SEG27
RC6
TX1
CK1
SEG27
31
RC7/RX1/DT1/SEG28
RC7
RX1
DT1
SEG28
32
I/O
O
I
ST
—
ST
I/O
I
I/O
O
ST
CMOS
ST
Analog
Digital I/O.
Timer1 oscillator input.
Capture2 input/Compare2 output/PWM2 output.
SEG32 output for LCD.
I/O
I/O
O
ST
ST
Analog
Digital I/O.
Capture1 input/Compare1 output/PWM1 output.
SEG13 output for LCD.
I/O
I/O
I/O
O
ST
ST
ST
Analog
Digital I/O.
Synchronous serial clock input/output for SPI mode.
Synchronous serial clock input/output for I2C™ mode.
SEG17 output for LCD.
I/O
I
I/O
O
ST
ST
ST
Analog
Digital I/O.
SPI data in.
I2C data I/O.
SEG16 output for LCD.
I/O
O
O
ST
—
Analog
Digital I/O.
SPI data out.
SEG12 output for LCD.
I/O
O
I/O
O
ST
—
ST
Analog
Digital I/O.
EUSART asynchronous transmit.
EUSART synchronous clock (see related RX1/DT1).
SEG27 output for LCD.
I/O
I
I/O
O
ST
ST
ST
Analog
Digital I/O.
EUSART asynchronous receive.
EUSART synchronous data (see related TX1/CK1).
SEG28 output for LCD.
Digital I/O.
Timer1 oscillator output.
Timer1/Timer3 external clock input.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
DS39770B-page 14
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 1-3:
PIC18F6XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTD is a bidirectional I/O port.
RD0/SEG0
RD0
SEG0
58
RD1/SEG1
RD1
SEG1
55
RD2/SEG2
RD2
SEG2
54
RD3/SEG3
RD3
SEG3
53
RD4/SEG4
RD4
SEG4
52
RD5/SEG5
RD5
SEG5
51
RD6/SEG6
RD6
SEG6
50
RD7/SEG7
RD7
SEG7
49
I/O
O
ST
Analog
Digital I/O.
SEG0 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG1 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG2 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG3 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG4 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG5 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG6 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG7 output for LCD.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 15
PIC18F85J90 FAMILY
TABLE 1-3:
PIC18F6XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTE is a bidirectional I/O port.
RE0/LCDBIAS1
RE0
LCDBIAS1
2
RE1/LCDBIAS2
RE1
LCDBIAS2
1
LCDBIAS3
64
RE3/COM0
RE3
COM0
63
RE4/COM1
RE4
COM1
62
RE5/COM2
RE5
COM2
61
RE6/COM3
RE6
COM3
60
RE7/CCP2/SEG31
RE7
CCP2(2)
SEG31
59
I/O
I
ST
Analog
Digital I/O.
BIAS1 input for LCD.
I/O
I
ST
Analog
Digital I/O.
BIAS2 input for LCD.
I
Analog
BIAS3 input for LCD.
I/O
O
ST
Analog
Digital I/O.
COM0 output for LCD.
I/O
O
ST
Analog
Digital I/O.
COM1 output for LCD.
I/O
O
ST
Analog
Digital I/O.
COM2 output for LCD.
I/O
O
ST
Analog
Digital I/O.
COM3 output for LCD.
I/O
I/O
O
ST
ST
Analog
Digital I/O.
Capture 2 input/Compare 2 output/PWM 2 output.
SEG31 output for LCD.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
DS39770B-page 16
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 1-3:
PIC18F6XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTF is a bidirectional I/O port.
RF1/AN6/C2OUT/SEG19
RF1
AN6
C2OUT
SEG19
17
RF2/AN7/C1OUT/SEG20
RF2
AN7
C1OUT
SEG20
16
RF3/AN8/SEG21
RF3
AN8
SEG21
15
RF4/AN9/SEG22
RF4
AN9
SEG22
14
RF5/AN10/CVREF/SEG23
RF5
AN10
CVREF
SEG23
13
RF6/AN11/SEG24
RF6
AN11
SEG24
12
RF7/AN5/SS/SEG25
RF7
AN5
SS
SEG25
11
I/O
I
O
O
ST
Analog
—
Analog
Digital I/O.
Analog input 6.
Comparator 2 output.
SEG19 output for LCD.
I/O
I
O
O
ST
Analog
—
Analog
Digital I/O.
Analog input 7.
Comparator 1 output.
SEG20 output for LCD.
I/O
I
O
ST
Analog
Analog
Digital I/O.
Analog input 8.
SEG21 output for LCD.
I/O
I
O
ST
Analog
Analog
Digital I/O.
Analog input 9.
SEG22 output for LCD.
I/O
I
O
O
ST
Analog
Analog
Analog
Digital I/O.
Analog input 10.
Comparator reference voltage output.
SEG23 output for LCD.
I/O
I
O
ST
Analog
Analog
Digital I/O.
Analog input 11.
SEG24 output for LCD.
I/O
O
I
O
ST
Analog
TTL
Analog
Digital I/O.
Analog input 5.
SPI slave select input.
SEG25 output for LCD.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 17
PIC18F85J90 FAMILY
TABLE 1-3:
PIC18F6XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTG is a bidirectional I/O port.
RG0/LCDBIAS0
RG0
LCDBIAS0
3
RG1/TX2/CK2
RG1
TX2
CK2
4
RG2/RX2/DT2/VLCAP1
RG2
RX2
DT2
VLCAP1
5
RG3/VLCAP2
RG3
VLCAP2
6
RG4/SEG26
RG4
SEG26
8
I/O
I
ST
Analog
Digital I/O.
BIAS0 input for LCD.
I/O
O
I/O
ST
—
ST
Digital I/O.
AUSART asynchronous transmit.
AUSART synchronous clock (see related RX2/DT2).
I/O
I
I/O
I
ST
ST
ST
Analog
Digital I/O.
AUSART asynchronous receive.
AUSART synchronous data (see related TX2/CK2).
LCD charge pump capacitor input.
I/O
I
ST
Analog
Digital I/O.
LCD charge pump capacitor input.
I/O
O
ST
Analog
Digital I/O.
SEG26 output for LCD.
VSS
9, 25, 41, 56
P
—
Ground reference for logic and I/O pins.
VDD
26, 38, 57
P
—
Positive supply for logic and I/O pins.
AVSS
20
P
—
Ground reference for analog modules.
AVDD
19
P
—
Positive supply for analog modules.
ENVREG
18
I
ST
Enable for on-chip voltage regulator.
VDDCORE/VCAP
VDDCORE
10
P
—
P
—
VCAP
Core logic power or external filter capacitor connection.
Positive supply for microcontroller core logic
(regulator disabled).
External filter capacitor connection (regulator enabled).
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
DS39770B-page 18
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 1-4:
PIC18F8XJ90 PINOUT I/O DESCRIPTIONS
Pin Number
Pin Name
TQFP
MCLR
9
OSC1/CLKI/RA7
OSC1
CLKI
49
Pin Buffer
Type Type
I
ST
I
I
CMOS
CMOS
I/O
TTL
O
—
CLKO
O
—
RA6
I/O
TTL
RA7
OSC2/CLKO/RA6
OSC2
50
Description
Master Clear (input) or programming voltage (input). This
pin is an active-low Reset to the device.
Oscillator crystal or external clock input.
Oscillator crystal input.
External clock source input. Always associated
with pin function OSC1. (See related OSC1/CLKI,
OSC2/CLKO pins.)
General purpose I/O pin.
Oscillator crystal or clock output.
Oscillator crystal output. Connects to crystal or
resonator in Crystal Oscillator mode.
In EC modes, OSC2 pin outputs CLKO, which has
1/4 the frequency of OSC1 and denotes the
instruction cycle rate.
General purpose I/O pin.
PORTA is a bidirectional I/O port.
RA0/AN0
RA0
AN0
30
RA1/AN1/SEG18
RA1
AN1
SEG18
29
RA2/AN2/VREFRA2
AN2
VREF-
28
RA3/AN3/VREF+
RA3
AN3
VREF+
27
RA4/T0CKI/SEG14
RA4
T0CKI
SEG14
34
RA5/AN4/SEG15
RA5
AN4
SEG15
33
I/O
I
TTL
Analog
Digital I/O.
Analog input 0.
I/O
I
O
TTL
Analog
Analog
Digital I/O.
Analog input 1.
SEG18 output for LCD.
I/O
I
I
TTL
Analog
Analog
Digital I/O.
Analog input 2.
A/D reference voltage (Low) input.
I/O
I
I
TTL
Analog
Analog
Digital I/O.
Analog input 3.
A/D reference voltage (High) input.
I/O
I
O
ST/OD
ST
Analog
Digital I/O. Open-drain when configured as output.
Timer0 external clock input.
SEG14 output for LCD.
I/O
I
O
TTL
Analog
Analog
Digital I/O.
Analog input 4.
SEG15 output for LCD.
RA6
See the OSC2/CLKO/RA6 pin.
RA7
See the OSC1/CLKI/RA7 pin.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 19
PIC18F85J90 FAMILY
TABLE 1-4:
PIC18F8XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTB is a bidirectional I/O port. PORTB can be software
programmed for internal weak pull-ups on all inputs.
RB0/INT0/SEG30
RB0
INT0
SEG30
58
RB1/INT1/SEG8
RB1
INT1
SEG8
57
RB2/INT2/SEG9
RB2
INT2
SEG9
56
RB3/INT3/SEG10
RB3
INT3
SEG10
55
RB4/KBI0/SEG11
RB4
KBI0
SEG11
54
RB5/KBI1/SEG29
RB5
KBI1
SEG29
53
RB6/KBI2/PGC
RB6
KBI2
PGC
52
RB7/KBI3/PGD
RB7
KBI3
PGD
47
I/O
I
O
TTL
ST
Analog
Digital I/O.
External interrupt 0.
SEG30 output for LCD.
I/O
I
O
TTL
ST
Analog
Digital I/O.
External interrupt 1.
SEG8 output for LCD.
I/O
I
O
TTL
ST
Analog
Digital I/O.
External interrupt 2.
SEG9 output for LCD.
I/O
I
O
TTL
ST
Analog
Digital I/O.
External interrupt 3.
SEG10 output for LCD.
I/O
I
O
TTL
TTL
Analog
Digital I/O.
Interrupt-on-change pin.
SEG11 output for LCD.
I/O
I
O
TTL
TTL
Analog
Digital I/O.
Interrupt-on-change pin.
SEG29 output for LCD.
I/O
I
I/O
TTL
TTL
ST
Digital I/O.
Interrupt-on-change pin.
In-Circuit Debugger and ICSP™ programming clock pin.
I/O
I
I/O
TTL
TTL
ST
Digital I/O.
Interrupt-on-change pin.
In-Circuit Debugger and ICSP programming data pin.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
DS39770B-page 20
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 1-4:
PIC18F8XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTC is a bidirectional I/O port.
RC0/T1OSO/T13CKI
RC0
T1OSO
T13CKI
36
RC1/T1OSI/CCP2/SEG32
RC1
T1OSI
CCP2(1)
SEG32
35
RC2/CCP1/SEG13
RC2
CCP1
SEG13
43
RC3/SCK/SCL/SEG17
RC3
SCK
SCL
SEG17
44
RC4/SDI/SDA/SEG16
RC4
SDI
SDA
SEG16
45
RC5/SDO/SEG12
RC5
SDO
SEG12
46
RC6/TX1/CK1/SEG27
RC6
TX1
CK1
SEG27
37
RC7/RX1/DT1/SEG28
RC7
RX1
DT1
SEG28
38
I/O
O
I
ST
—
ST
I/O
I
I/O
O
ST
CMOS
ST
Analog
Digital I/O.
Timer1 oscillator input.
Capture2 input/Compare2 output/PWM2 output.
SEG32 output for LCD.
I/O
I/O
O
ST
ST
Analog
Digital I/O.
Capture1 input/Compare1 output/PWM1 output.
SEG13 output for LCD.
I/O
I/O
I/O
O
ST
ST
ST
Analog
Digital I/O.
Synchronous serial clock input/output for SPI mode.
Synchronous serial clock input/output for I2C™ mode.
SEG17 output for LCD.
I/O
I
I/O
O
ST
ST
ST
Analog
Digital I/O.
SPI data in.
I2C data I/O.
SEG16 output for LCD.
I/O
O
O
ST
—
Analog
Digital I/O.
SPI data out.
SEG12 output for LCD.
I/O
O
I/O
O
ST
—
ST
Analog
Digital I/O.
EUSART asynchronous transmit.
EUSART synchronous clock (see related RX1/DT1).
SEG27 output for LCD.
I/O
I
I/O
O
ST
ST
ST
Analog
Digital I/O.
EUSART asynchronous receive.
EUSART synchronous data (see related TX1/CK1).
SEG28 output for LCD.
Digital I/O.
Timer1 oscillator output.
Timer1/Timer3 external clock input.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 21
PIC18F85J90 FAMILY
TABLE 1-4:
PIC18F8XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTD is a bidirectional I/O port.
RD0/SEG0
RD0
SEG0
72
RD1/SEG1
RD1
SEG1
69
RD2/SEG2
RD2
SEG2
68
RD3/SEG3
RD3
SEG3
67
RD4/SEG4
RD4
SEG4
66
RD5/SEG5
RD5
SEG5
65
RD6/SEG6
RD6
SEG6
64
RD7/SEG7
RD7
SEG7
63
I/O
O
ST
Analog
Digital I/O.
SEG0 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG1 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG2 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG3 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG4 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG5 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG6 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG7 output for LCD.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
DS39770B-page 22
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 1-4:
PIC18F8XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTE is a bidirectional I/O port.
RE0/LCDBIAS1
RE0
LCDBIAS1
4
RE1/LCDBIAS2
RE1
LCDBIAS2
3
LCDBIAS3
78
RE3/COM0
RE3
COM0
77
RE4/COM1
RE4
COM1
76
RE5/COM2
RE5
COM2
75
RE6/COM3
RE6
COM3
74
RE7/CCP2/SEG31
RE7
CCP2(2)
SEG31
73
I/O
I
ST
Analog
Digital I/O.
BIAS1 input for LCD.
I/O
I
ST
Analog
Digital I/O.
BIAS2 input for LCD.
I
Analog
BIAS3 input for LCD.
I/O
O
ST
Analog
Digital I/O.
COM0 output for LCD.
I/O
O
ST
Analog
Digital I/O.
COM1 output for LCD.
I/O
O
ST
Analog
Digital I/O.
COM2 output for LCD.
I/O
O
ST
Analog
Digital I/O.
COM3 output for LCD.
I/O
I/O
O
ST
ST
Analog
Digital I/O.
Capture 2 input/Compare 2 output/PWM 2 output.
SEG31 output for LCD.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 23
PIC18F85J90 FAMILY
TABLE 1-4:
PIC18F8XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTF is a bidirectional I/O port.
RF1/AN6/C2OUT/SEG19
RF1
AN6
C2OUT
SEG19
23
RF2/AN7/C1OUT/SEG20
RF2
AN7
C1OUT
SEG20
18
RF3/AN8/SEG21
RF3
AN8
SEG21
17
RF4/AN9/SEG22
RF4
AN9
SEG22
16
RF5/AN10/CVREF/SEG23
RF5
AN10
CVREF
SEG23
15
RF6/AN11/SEG24
RF6
AN11
SEG24
14
RF7/AN5/SS/SEG25
RF7
AN5
SS
SEG25
13
I/O
I
O
O
ST
Analog
—
Analog
Digital I/O.
Analog input 6.
Comparator 2 output.
SEG19 output for LCD.
I/O
I
O
O
ST
Analog
—
Analog
Digital I/O.
Analog input 7.
Comparator 1 output.
SEG20 output for LCD.
I/O
I
O
ST
Analog
Analog
Digital I/O.
Analog input 8.
SEG21 output for LCD.
I/O
I
O
ST
Analog
Analog
Digital I/O.
Analog input 9.
SEG22 output for LCD.
I/O
I
O
O
ST
Analog
Analog
Analog
Digital I/O.
Analog input 10.
Comparator reference voltage output.
SEG23 output for LCD.
I/O
I
O
ST
Analog
Analog
Digital I/O.
Analog input 11.
SEG24 output for LCD.
I/O
O
I
O
ST
Analog
TTL
Analog
Digital I/O.
Analog input 5.
SPI slave select input.
SEG25 output for LCD.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
DS39770B-page 24
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 1-4:
PIC18F8XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTG is a bidirectional I/O port.
RG0/LCDBIAS0
RG0
LCDBIAS0
5
RG1/TX2/CK2
RG1
TX2
CK2
6
RG2/RX2/DT2/VLCAP1
RG2
RX2
DT2
VLCAP1
7
RG3/VLCAP2
RG3
VLCAP2
8
RG4/SEG26
RG4
SEG26
10
I/O
I
ST
Analog
Digital I/O.
BIAS0 input for LCD.
I/O
O
I/O
ST
—
ST
Digital I/O.
AUSART asynchronous transmit.
AUSART synchronous clock (see related RX2/DT2).
I/O
I
I/O
I
ST
ST
ST
Analog
Digital I/O.
AUSART asynchronous receive.
AUSART synchronous data (see related TX2/CK2).
LCD charge pump capacitor input.
I/O
I
ST
Analog
Digital I/O.
LCD charge pump capacitor input.
I/O
O
ST
Analog
Digital I/O.
SEG26 output for LCD.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 25
PIC18F85J90 FAMILY
TABLE 1-4:
PIC18F8XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTH is a bidirectional I/O port.
RH0/SEG47
RH0
SEG47
79
RH1/SEG46
RH1
SEG46
80
RH2/SEG45
RH2
SEG45
1
RH3/SEG44
RH3
SEG44
2
RH4/SEG40
RH4
SEG40
22
RH5/SEG41
RH5
SEG41
21
RH6/SEG42
RH6
SEG42
20
RH7/SEG43
RH7
SEG43
19
I/O
O
ST
Analog
Digital I/O.
SEG47 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG46 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG45 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG44 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG40 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG41 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG42 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG43 output for LCD.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
DS39770B-page 26
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 1-4:
PIC18F8XJ90 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
TQFP
Pin Buffer
Type Type
Description
PORTJ is a bidirectional I/O port.
RJ0
62
RJ1/SEG33
RJ1
SEG33
61
RJ2/SEG34
RJ2
SEG34
60
RJ3/SEG35
RJ3
SEG35
59
RJ4/SEG39
RJ4
SEG39
39
RJ5/SEG38
RJ5
SEG38
40
RJ6/SEG37
RJ6
SEG37
41
RJ7/SEG36
RJ7
SEG36
42
I/O
ST
Digital I/O.
I/O
O
ST
Analog
Digital I/O.
SEG33 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG34 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG35 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG39 output for LCD.
I/O
O
ST
Analog
Digital I/O
SEG38 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG37 output for LCD.
I/O
O
ST
Analog
Digital I/O.
SEG36 output for LCD.
VSS
11, 31, 51, 70
P
—
Ground reference for logic and I/O pins.
VDD
32, 48, 71
P
—
Positive supply for logic and I/O pins.
AVSS
26
P
—
Ground reference for analog modules.
AVDD
25
P
—
Positive supply for analog modules.
ENVREG
24
I
ST
VDDCORE/VCAP
VDDCORE
12
VCAP
P
—
P
—
Enable for on-chip voltage regulator.
Core logic power or external filter capacitor connection.
Positive supply for microcontroller core logic
(regulator disabled).
External filter capacitor connection (regulator enabled).
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
Analog = Analog input
I
= Input
O
= Output
P
= Power
OD
= Open-Drain (no P diode to VDD)
Note 1: Default assignment for CCP2 when CCP2MX Configuration bit is set.
2: Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 27
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 28
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
2.0
OSCILLATOR
CONFIGURATIONS
2.1
Oscillator Types
Five of these are selected by the user by programming
the FOSC2:FOSC0 Configuration bits. The sixth mode
(INTRC) may be invoked under software control; it can
also be configured as the default mode on device
Resets.
The PIC18F85J90 family of devices can be operated in
six different oscillator modes:
1.
2.
3.
4.
5.
6.
HS
High-Speed Crystal/Resonator
HSPLL High-Speed Crystal/Resonator
with Software PLL Control
EC
External Clock with FOSC/4 Output
ECPLL External Clock with Software PLL
Control
INTOSC Internal Fast RC (8 MHz) oscillator
INTRC Internal 31 kHz Oscillator
FIGURE 2-1:
In addition, PIC18F85J90 family devices can switch
between different clock sources, either under software
control, or automatically under certain conditions. This
allows for additional power savings by managing
device clock speed in real time without resetting the
application.
The clock sources for the PIC18F85J90 family of
devices are shown in Figure 2-1.
PIC18F85J90 FAMILY CLOCK DIAGRAM
PIC18F85J90 Family
Primary Oscillator
HS, EC
OSC2
Sleep
4 x PLL
HSPLL, ECPLL
OSC1
T1OSC
OSCCON<6:4>
OSCCON<6:4>
8 MHz
4 MHz
Internal
Oscillator
Block
8 MHz
(INTOSC)
Postscaler
8 MHz
Source
2 MHz
1 MHz
500 kHz
250 kHz
125 kHz
1 31 kHz
0
INTRC
Source
© 2007 Microchip Technology Inc.
Internal Oscillator
CPU
111
110
IDLEN
101
100
011
MUX
T1OSI
T1OSCEN
Enable
Oscillator
Peripherals
MUX
Secondary Oscillator
T1OSO
010
001
000
Clock
Control
FOSC2:FOSC0
OSCCON<1:0>
Clock Source Option
for other modules
OSCTUNE<7>
31 kHz (INTRC)
WDT, PWRT, FSCM
and Two-Speed Start-up
Preliminary
DS39770B-page 29
PIC18F85J90 FAMILY
2.2
Control Registers
The OSCTUNE register (Register 2-2) controls the
tuning and operation of the internal oscillator block. It
also implements the PLLEN bits, which control the
operation of the Phase Locked Loop (PLL) in Internal
Oscillator modes (see Section 2.4.3 “PLL Frequency
Multiplier”).
The OSCCON register (Register 2-1) controls the main
aspects of the device clock’s operation. It selects the
oscillator type to be used, which of the power-managed
modes to invoke and the output frequency of the
INTOSC source. It also provides status on the
oscillators.
REGISTER 2-1:
OSCCON: OSCILLATOR CONTROL REGISTER
R/W-0
R/W-1
R/W-0
R/W-0
R(1)
R-0
R/W-0
R/W-0
IDLEN
IRCF2
IRCF1
IRCF0
OSTS
IOFS
SCS1
SCS0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
IDLEN: Idle Enable bit
1 = Device enters an Idle mode when a SLEEP instruction is executed
0 = Device enters Sleep mode when a SLEEP instruction is executed
bit 6-4
IRCF2:IRCF0: INTOSC Source Frequency Select bits(2)
111 = 8 MHz (INTOSC drives clock directly)
110 = 4 MHz
101 = 2 MHz
100 = 1 MHz (default)
011 = 500 kHz
010 = 250 kHz
001 = 125 kHz
000 = 31 kHz (from either INTOSC/256 or INTRC)(3)
bit 3
OSTS: Oscillator Start-up Time-out Status bit(1)
1 = Oscillator Start-up Timer (OST) time-out has expired; primary oscillator is running
0 = Oscillator Start-up Timer (OST) time-out is running; primary oscillator is not ready
bit 2
IOFS: INTOSC Frequency Stable bit
1 = Fast RC oscillator frequency is stable
0 = Fast RC oscillator frequency is not stable
bit 1-0
SCS1:SCS0: System Clock Select bits(4)
11 = Internal oscillator block
10 = Primary oscillator
01 = Timer1 oscillator
When FOSC2 = 1:
00 = Primary oscillator
When FOSC2 = 0:
00 = Internal oscillator
Note 1:
2:
3:
4:
Reset state depends on state of the IESO Configuration bit.
Modifying these bits will cause an immediate clock frequency switch if the internal oscillator is providing
the device clocks.
Source selected by the INTSRC bit (OSCTUNE<7>), see text.
Modifying these bits will cause an immediate clock source switch.
DS39770B-page 30
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 2-2:
R/W-0
INTSRC
OSCTUNE: OSCILLATOR TUNING REGISTER
R/W-0
PLLEN
(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TUN5
TUN4
TUN3
TUN2
TUN1
TUN0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
INTSRC: Internal Oscillator Low-Frequency Source Select bit
1 = 31.25 kHz device clock derived from 8 MHz INTOSC source (divide-by-256 enabled)
0 = 31 kHz device clock derived from INTRC 31 kHz oscillator
bit 6
PLLEN: Frequency Multiplier PLL Enable bit(1)
1 = PLL enabled
0 = PLL disabled
bit 5-0
TUN5:TUN0: Fast RC Oscillator (INTOSC) Frequency Tuning bits
011111 = Maximum frequency
•
•
•
•
000001
000000 = Center frequency. Fast RC oscillator is running at the calibrated frequency.
111111
•
•
•
•
100000 = Minimum frequency
Note 1:
2.3
Available only for ECPLL and HSPLL oscillator configurations; otherwise, this bit is unavailable and reads
as ‘0’.
Clock Sources and
Oscillator Switching
Essentially, PIC18F85J90 family devices have three
independent clock sources:
• Primary oscillators
• Secondary oscillators
• Internal oscillator
The primary oscillators can be thought of as the main
device oscillators. These are any external oscillators
connected to the OSC1 and OSC2 pins, and include
the External Crystal and Resonator modes and the
External Clock modes. In some circumstances, the
internal oscillator block may be considered a primary
oscillator. The particular mode is defined by the FOSC
Configuration bits. The details of these modes are
covered in Section 2.4 “External Oscillator Modes”.
The secondary oscillators are external clock sources
that are not connected to the OSC1 or OSC2 pins.
These sources may continue to operate even after the
controller is placed in a power-managed mode.
© 2007 Microchip Technology Inc.
PIC18F85J90 family devices offer the Timer1 oscillator
as a secondary oscillator source. This oscillator, in all
power-managed modes, is often the time base for
functions such as a Real-Time Clock. The Timer1 oscillator is discussed in greater detail in Section 11.3
“Timer1 Oscillator”
In addition to being a primary clock source in some circumstances, the internal oscillator is available as a
power-managed mode clock source. The INTRC
source is also used as the clock source for several
special features, such as the WDT and Fail-Safe Clock
Monitor. The internal oscillator block is discussed in
more detail in Section 2.5 “Internal Oscillator
Block”.
The PIC18F85J90 family includes features that allow
the device clock source to be switched from the main
oscillator, chosen by device configuration, to one of the
alternate clock sources. When an alternate clock
source is enabled, various power-managed operating
modes are available.
Preliminary
DS39770B-page 31
PIC18F85J90 FAMILY
2.3.1
CLOCK SOURCE SELECTION
2.3.1.1
The System Clock Select bits, SCS1:SCS0
(OSCCON<1:0>), select the clock source. The available clock sources are the primary clock defined by the
FOSC1:FOSC0 Configuration bits, the secondary
clock (Timer1 oscillator) and the internal oscillator. The
clock source changes after one or more of the bits are
written to, following a brief clock transition interval.
The OSTS (OSCCON<3>) and T1RUN (T1CON<6>)
bits indicate which clock source is currently providing
the device clock. The OSTS bit indicates that the
Oscillator Start-up Timer (OST) has timed out and the
primary clock is providing the device clock in primary
clock modes. The T1RUN bit indicates when the
Timer1 oscillator is providing the device clock in secondary clock modes. In power-managed modes, only
one of these bits will be set at any time. If neither of
these bits are set, the INTRC is providing the clock, or
the internal oscillator has just started and is not yet
stable.
The IDLEN bit determines if the device goes into Sleep
mode or one of the Idle modes when the SLEEP
instruction is executed.
The use of the flag and control bits in the OSCCON
register is discussed in more detail in Section 3.0
“Power-Managed Modes”.
Note 1: The Timer1 oscillator must be enabled to
select the secondary clock source. The
Timer1 oscillator is enabled by setting the
T1OSCEN bit in the Timer1 Control register (T1CON<3>). If the Timer1 oscillator is
not enabled, then any attempt to select a
secondary clock source when executing a
SLEEP instruction will be ignored.
2: It is recommended that the Timer1
oscillator be operating and stable before
executing the SLEEP instruction or a very
long delay may occur while the Timer1
oscillator starts.
System Clock Selection and the
FOSC2 Configuration Bit
The SCS bits are cleared on all forms of Reset. In the
device’s default configuration, this means the primary
oscillator defined by FOSC1:FOSC0 (that is, one of the
HS or EC modes) is used as the primary clock source
on device Resets.
The default clock configuration on Reset can be
changed with the FOSC2 Configuration bit. This bit
determines whether the external or internal oscillator
will be the default clock source on subsequent device
Resets. By extension, it also has the effect of determining the clock source selected when SCS1:SCS0 are in
their Reset state (= 00). When FOSC2 = 1 (default), the
oscillator source defined by FOSC1:FOSC0 is selected
whenever SCS1:SCS0 = 00. When FOSC2 = 0, the
internal oscillator block is selected whenever
SCS1:SCS2 = 00.
In those cases when the internal oscillator block is the
default clock on Reset, the Fast RC oscillator
(INTOSC) will be used as the device clock source. It will
initially start at 1 MHz, the postscaler selection that corresponds to the Reset value of the IRCF2:IRCF0 bits
(‘100’).
Regardless of the setting of FOSC2, INTRC will always
be enabled on device power-up. It serves as the clock
source until the device has loaded its configuration
values from memory. It is at this point that the FOSC
Configuration bits are read and the oscillator selection
of the operational mode is made.
Note that either the primary clock or the internal
oscillator will have two bit setting options for the
possible values of SCS1:SCS0, at any given time,
depending on the setting of FOSC2.
2.3.2
OSCILLATOR TRANSITIONS
PIC18F85J90 family devices contain circuitry to
prevent clock “glitches” when switching between clock
sources. A short pause in the device clock occurs during the clock switch. The length of this pause is the sum
of two cycles of the old clock source and three to four
cycles of the new clock source. This formula assumes
that the new clock source is stable.
Clock transitions are discussed in greater detail in
Section 3.1.2 “Entering Power-Managed Modes”.
DS39770B-page 32
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
2.4
TABLE 2-2:
External Oscillator Modes
2.4.1
CRYSTAL OSCILLATOR/CERAMIC
RESONATORS (HS MODES)
In HS or HSPLL Oscillator modes, a crystal or ceramic
resonator is connected to the OSC1 and OSC2 pins to
establish oscillation. Figure 2-2 shows the pin
connections.
The oscillator design requires the use of a parallel cut
crystal.
Note:
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
Use of a series cut crystal may give a frequency out of the crystal manufacturer’s
specifications.
TABLE 2-1:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
Typical Capacitor Values Used:
Mode
Freq.
OSC1
OSC2
HS
8.0 MHz
16.0 MHz
27 pF
22 pF
27 pF
22 pF
Capacitor values are for design guidance only.
Osc Type
HS
C1
C2
4 MHz
27 pF
27 pF
8 MHz
22 pF
22 pF
20 MHz
15 pF
15 pF
Capacitor values are for design guidance only.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
VDD and temperature range for the application.
Refer to the Microchip application notes cited in
Table 2-1 for oscillator specific information. Also see
the notes following this table for additional
information.
Note 1: Higher capacitance increases the
stability of oscillator but also increases
the start-up time.
2: Since each resonator/crystal has its own
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate
values
of
external
components.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
VDD and temperature range for the application. Refer
to the following application notes for oscillator specific
information:
• AN588, “PIC® Microcontroller Oscillator Design
Guide”
• AN826, “Crystal Oscillator Basics and Crystal
Selection for rfPIC® and PIC® Devices”
• AN849, 'Basic PIC® Oscillator Design”
• AN943, “Practical PIC® Oscillator Analysis and
Design”
• AN949, “Making Your Oscillator Work”
Typical Capacitor Values
Tested:
Crystal
Freq.
3: Rs may be required to avoid overdriving
crystals with low drive level specification.
4: Always verify oscillator performance over
the VDD and temperature range that is
expected for the application.
FIGURE 2-2:
See the notes following Table 2-2 for additional
information.
CRYSTAL/CERAMIC
RESONATOR OPERATION
(HS OR HSPLL
CONFIGURATION)
C1(1)
OSC1
XTAL
RF(3)
OSC2
C2(1)
© 2007 Microchip Technology Inc.
To
Internal
Logic
RS(2)
Sleep
PIC18F85J90
Note 1:
See Table 2-1 and Table 2-2 for initial values of
C1 and C2.
2:
A series resistor (RS) may be required for AT
strip cut crystals.
3:
RF varies with the oscillator mode chosen.
Preliminary
DS39770B-page 33
PIC18F85J90 FAMILY
2.4.2
2.4.3
EXTERNAL CLOCK INPUT
(EC MODES)
The EC and ECPLL Oscillator modes require an external clock source to be connected to the OSC1 pin.
There is no oscillator start-up time required after a
Power-on Reset or after an exit from Sleep mode.
In the EC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic. Figure 2-3 shows the pin connections for the EC
Oscillator mode.
FIGURE 2-3:
EXTERNAL CLOCK
INPUT OPERATION
(EC CONFIGURATION)
OSC1/CLKI
Clock from
Ext. System
PIC18F85J90
FOSC/4
or RA6
PLL FREQUENCY MULTIPLIER
A Phase Locked Loop (PLL) circuit is provided as an
option for users who want to use a lower frequency
oscillator circuit, or to clock the device up to its highest
rated frequency from a crystal oscillator. This may be
useful for customers who are concerned with EMI due
to high-frequency crystals, or users who require higher
clock speeds from an internal oscillator. For these
reasons, the HSPLL and ECPLL modes are available.
The HSPLL and ECPLL modes provide the ability to
selectively run the device at 4 times the external oscillating source to produce frequencies up to 40 MHz.
The PLL is enabled by programming the
FOSC2:FOSC0 Configuration bits (CONFIG2L<2:0>)
to either ‘110’ (for ECPLL) or ‘100’ (for HSPLL). In
addition, the PLLEN bit (OSCTUNE<6>) must also be
set. Clearing PLLEN disables the PLL, regardless of
the chosen oscillator configuration. It also allows
additional flexibility for controlling the application’s
clock speed in software.
OSC2/CLKO
FIGURE 2-5:
HSPLL or ECPLL (CONFIG2L)
PLL Enable (OSCTUNE)
An external clock source may also be connected to the
OSC1 pin in the HS mode, as shown in Figure 2-4. In
this configuration, the divide-by-4 output on OSC2 is
not available.
OSC2
FIGURE 2-4:
HS or EC
OSC1 Mode
EXTERNAL CLOCK INPUT
OPERATION (HS OSC
CONFIGURATION)
PLL BLOCK DIAGRAM
FIN
FOUT
Phase
Comparator
Loop
Filter
OSC1
Clock from
Ext. System
PIC18F85J90
DS39770B-page 34
OSC2
÷4
(HS Mode)
VCO
MUX
Open
Preliminary
SYSCLK
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
2.5
2.5.3
Internal Oscillator Block
The PIC18F85J90 family of devices includes an internal
oscillator block which generates two different clock
signals; either can be used as the microcontroller’s clock
source. This may eliminate the need for an external
oscillator circuit on the OSC1 and/or OSC2 pins.
The main output is the Fast RC oscillator, or INTOSC,
an 8 MHz clock source which can be used to directly
drive the device clock. It also drives a postscaler, which
can provide a range of clock frequencies from 31 kHz
to 4 MHz. INTOSC is enabled when a clock frequency
from 125 kHz to 8 MHz is selected. The INTOSC output can also be enabled when 31 kHz is selected,
depending on the INTSRC bit (OSCTUNE<7>).
The other clock source is the Internal RC oscillator
(INTRC), which provides a nominal 31 kHz output.
INTRC is enabled if it is selected as the device clock
source. It is also enabled automatically when any of the
following are enabled:
• Power-up Timer
• Fail-Safe Clock Monitor
• Watchdog Timer
• Two-Speed Start-up
These features are discussed in greater detail in
Section 22.0 “Special Features of the CPU”.
The clock source frequency (INTOSC direct, INTOSC
with postscaler or INTRC direct) is selected by configuring the IRCF bits of the OSCCON register. The
default frequency on device Resets is 1 MHz.
2.5.1
OSC1 AND OSC2 PIN
CONFIGURATION
Whenever the internal oscillator is configured as the
default clock source (FOSC2 = 0), the OSC1 and OSC2
pins are reconfigured automatically as port pins, RA6
and RA7. In this mode, they function as general digital
I/O. All oscillator functions on the pins are disabled.
2.5.2
INTERNAL OSCILLATOR OUTPUT
FREQUENCY AND TUNING
The internal oscillator block is calibrated at the factory
to produce an INTOSC output frequency of 8 MHz. It
can be adjusted in the user’s application by writing to
TUN5:TUN0 (OSCTUNE<5:0>) in the OSCTUNE
register (Register 2-2).
When the OSCTUNE register is modified, the INTOSC
frequency will begin shifting to the new frequency. The
oscillator will stabilize within 1 ms. Code execution continues during this shift. There is no indication that the
shift has occurred.
The INTRC oscillator operates independently of the
INTOSC source. Any changes in INTOSC across
voltage and temperature are not necessarily reflected
by changes in INTRC or vice versa. The frequency of
INTRC is not affected by OSCTUNE.
© 2007 Microchip Technology Inc.
INTOSC FREQUENCY DRIFT
The INTOSC frequency may drift as VDD or temperature changes, and can affect the controller operation in
a variety of ways. It is possible to adjust the INTOSC
frequency by modifying the value in the OSCTUNE
register. This will have no effect on the INTRC clock
source frequency.
Tuning INTOSC requires knowing when to make the
adjustment, in which direction it should be made and in
some cases, how large a change is needed. Three
compensation techniques are shown here.
2.5.3.1
Compensating with the EUSART
An adjustment may be required when the EUSART
begins to generate framing errors or receives data with
errors while in Asynchronous mode. Framing errors
indicate that the device clock frequency is too high. To
adjust for this, decrement the value in OSCTUNE to
reduce the clock frequency. On the other hand, errors
in data may suggest that the clock speed is too low. To
compensate, increment OSCTUNE to increase the
clock frequency.
2.5.3.2
Compensating with the Timers
This technique compares device clock speed to some
reference clock. Two timers may be used; one timer is
clocked by the peripheral clock, while the other is
clocked by a fixed reference source, such as the
Timer1 oscillator.
Both timers are cleared, but the timer clocked by the
reference generates interrupts. When an interrupt
occurs, the internally clocked timer is read and both
timers are cleared. If the internally clocked timer value
is much greater than expected, then the internal
oscillator block is running too fast. To adjust for this,
decrement the OSCTUNE register.
2.5.3.3
Compensating with the CCP Module
in Capture Mode
A CCP module can use free-running Timer1 (or
Timer3), clocked by the internal oscillator block and an
external event with a known period (i.e., AC power
frequency). The time of the first event is captured in the
CCPRxH:CCPRxL registers and is recorded for use
later. When the second event causes a capture, the
time of the first event is subtracted from the time of the
second event. Since the period of the external event is
known, the time difference between events can be
calculated.
If the measured time is much greater than the
calculated time, the internal oscillator block is running
too fast. To compensate, decrement the OSCTUNE
register. If the measured time is much less than the
calculated time, the internal oscillator block is running
too slow. To compensate, increment the OSCTUNE
register.
Preliminary
DS39770B-page 35
PIC18F85J90 FAMILY
2.6
Effects of Power-Managed Modes
on the Various Clock Sources
When PRI_IDLE mode is selected, the designated primary oscillator continues to run without interruption.
For all other power-managed modes, the oscillator
using the OSC1 pin is disabled. The OSC1 pin (and
OSC2 pin if used by the oscillator) will stop oscillating.
In secondary clock modes (SEC_RUN and
SEC_IDLE), the Timer1 oscillator is operating and
providing the device clock. The Timer1 oscillator may
also run in all power-managed modes if required to
clock Timer1 or Timer3.
In RC_RUN and RC_IDLE modes, the internal oscillator provides the device clock source. The 31 kHz
INTRC output can be used directly to provide the clock
and may be enabled to support various special
features, regardless of the power-managed mode (see
Section 22.2 “Watchdog Timer (WDT)” through
Section 22.5 “Fail-Safe Clock Monitor” for more
information on WDT, Fail-Safe Clock Monitor and
Two-Speed Start-up).
If the Sleep mode is selected, all clock sources are
stopped. Since all the transistor switching currents
have been stopped, Sleep mode achieves the lowest
current consumption of the device (only leakage
currents).
Enabling any on-chip feature that will operate during
Sleep will increase the current consumed during Sleep.
The INTRC is required to support WDT operation. The
TABLE 2-3:
Timer1 oscillator may be operating to support a RealTime Clock. Other features may be operating that do
not require a device clock source (i.e., MSSP slave,
PSP, INTn pins and others). Peripherals that may add
significant current consumption are listed in
Section 25.2 “DC Characteristics: Power-Down and
Supply Current”.
2.7
Power-up Delays
Power-up delays are controlled by two timers, so that
no external Reset circuitry is required for most applications. The delays ensure that the device is kept in
Reset until the device power supply is stable under normal circumstances and the primary clock is operating
and stable. For additional information on power-up
delays, see Section 4.5 “Power-up Timer (PWRT)”.
The first timer is the Power-up Timer (PWRT), which
provides a fixed delay on power-up (parameter 33,
Table 25-11). It is always enabled.
The second timer is the Oscillator Start-up Timer
(OST), intended to keep the chip in Reset until the
crystal oscillator is stable (HS modes). The OST does
this by counting 1024 oscillator cycles before allowing
the oscillator to clock the device.
There is a delay of interval TCSD (parameter 38,
Table 25-11), following POR, while the controller
becomes ready to execute instructions.
OSC1 AND OSC2 PIN STATES IN SLEEP MODE
Oscillator Mode
OSC1 Pin
OSC2 Pin
EC, ECPLL
Floating, pulled by external clock
At logic low (clock/4 output)
HS, HSPLL
Feedback inverter disabled at quiescent
voltage level
Feedback inverter disabled at quiescent
voltage level
INTOSC
I/O pin RA6, direction controlled by
TRISA<6>
I/O pin RA7, direction controlled by
TRISA<7>
Note:
See Table 4-2 in Section 4.0 “Reset” for time-outs due to Sleep and MCLR Reset.
DS39770B-page 36
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
3.0
POWER-MANAGED MODES
3.1.1
CLOCK SOURCES
The PIC18F85J90 family devices provide the ability to
manage power consumption by simply managing clocking to the CPU and the peripherals. In general, a lower
clock frequency and a reduction in the number of circuits
being clocked constitutes lower consumed power. For
the sake of managing power in an application, there are
three primary modes of operation:
The SCS1:SCS0 bits allow the selection of one of three
clock sources for power-managed modes. They are:
• Run mode
• Idle mode
• Sleep mode
3.1.2
These modes define which portions of the device are
clocked and at what speed. The Run and Idle modes
may use any of the three available clock sources
(primary, secondary or internal oscillator block); the
Sleep mode does not use a clock source.
The power-managed modes include several
power-saving features offered on previous PIC®
devices. One is the clock switching feature, offered in
other PIC18 devices, allowing the controller to use the
Timer1 oscillator in place of the primary oscillator. Also
included is the Sleep mode, offered by all PIC devices,
where all device clocks are stopped.
3.1
Selecting Power-Managed Modes
Selecting a power-managed mode requires two
decisions: if the CPU is to be clocked or not and which
clock source is to be used. The IDLEN bit
(OSCCON<7>) controls CPU clocking, while the
SCS1:SCS0 bits (OSCCON<1:0>) select the clock
source. The individual modes, bit settings, clock
sources and affected modules are summarized in
Table 3-1.
TABLE 3-1:
• the primary clock, as defined by the
FOSC2:FOSC0 Configuration bits
• the secondary clock (Timer1 oscillator)
• the internal oscillator
ENTERING POWER-MANAGED
MODES
Switching from one power-managed mode to another
begins by loading the OSCCON register. The
SCS1:SCS0 bits select the clock source and determine
which Run or Idle mode is to be used. Changing these
bits causes an immediate switch to the new clock
source, assuming that it is running. The switch may
also be subject to clock transition delays. These are
discussed in Section 3.1.3 “Clock Transitions and
Status Indicators” and subsequent sections.
Entry to the power-managed Idle or Sleep modes is
triggered by the execution of a SLEEP instruction. The
actual mode that results depends on the status of the
IDLEN bit.
Depending on the current mode and the mode being
switched to, a change to a power-managed mode does
not always require setting all of these bits. Many
transitions may be done by changing the oscillator
select bits, or changing the IDLEN bit, prior to issuing a
SLEEP instruction. If the IDLEN bit is already
configured correctly, it may only be necessary to
perform a SLEEP instruction to switch to the desired
mode.
POWER-MANAGED MODES
OSCCON bits
Mode
(1)
IDLEN<7>
Module Clocking
Available Clock and Oscillator Source
SCS1:SCS0<1:0>
CPU
Peripherals
0
N/A
Off
Off
PRI_RUN
N/A
10
Clocked
Clocked
Primary – HS, EC, HSPLL, ECPLL;
this is the normal full power execution mode
SEC_RUN
N/A
01
Clocked
Clocked
Secondary – Timer1 Oscillator
RC_RUN
N/A
11
Clocked
Clocked
Internal Oscillator
PRI_IDLE
1
10
Off
Clocked
Primary – HS, EC, HSPLL, ECPLL
SEC_IDLE
1
01
Off
Clocked
Secondary – Timer1 Oscillator
RC_IDLE
1
11
Off
Clocked
Internal Oscillator
Sleep
Note 1:
None – All clocks are disabled
IDLEN reflects its value when the SLEEP instruction is executed.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 37
PIC18F85J90 FAMILY
3.1.3
CLOCK TRANSITIONS AND STATUS
INDICATORS
The length of the transition between clock sources is
the sum of two cycles of the old clock source and three
to four cycles of the new clock source. This formula
assumes that the new clock source is stable.
Two bits indicate the current clock source and its
status:
OSTS
(OSCCON<3>)
and
T1RUN
(T1CON<6>). In general, only one of these bits will be
set while in a given power-managed mode. When the
OSTS bit is set, the primary clock is providing the
device clock. When the T1RUN bit is set, the Timer1
oscillator is providing the clock. If neither of these bits
is set, INTRC is clocking the device.
Note:
3.1.4
Executing a SLEEP instruction does not
necessarily place the device into Sleep
mode. It acts as the trigger to place the
controller into either the Sleep mode, or
one of the Idle modes, depending on the
setting of the IDLEN bit.
MULTIPLE SLEEP COMMANDS
The power-managed mode that is invoked with the
SLEEP instruction is determined by the setting of the
IDLEN bit at the time the instruction is executed. If
another SLEEP instruction is executed, the device will
enter the power-managed mode specified by IDLEN at
that time. If IDLEN has changed, the device will enter
the new power-managed mode specified by the new
setting.
DS39770B-page 38
3.2
Run Modes
In the Run modes, clocks to both the core and
peripherals are active. The difference between these
modes is the clock source.
3.2.1
PRI_RUN MODE
The PRI_RUN mode is the normal, full power execution
mode of the microcontroller. This is also the default
mode upon a device Reset unless Two-Speed Start-up
is enabled (see Section 22.4 “Two-Speed Start-up”
for details). In this mode, the OSTS bit is set (see
Section 2.2 “Control Registers”).
3.2.2
SEC_RUN MODE
The SEC_RUN mode is the compatible mode to the
“clock switching” feature offered in other PIC18
devices. In this mode, the CPU and peripherals are
clocked from the Timer1 oscillator. This gives users the
option of lower power consumption while still using a
high-accuracy clock source.
SEC_RUN mode is entered by setting the SCS1:SCS0
bits to ‘01’. The device clock source is switched to the
Timer1 oscillator (see Figure 3-1), the primary oscillator is shut down, the T1RUN bit (T1CON<6>) is set and
the OSTS bit is cleared.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
Note:
On transitions from SEC_RUN mode to PRI_RUN
mode, the peripherals and CPU continue to be clocked
from the Timer1 oscillator while the primary clock is
started. When the primary clock becomes ready, a
clock switch back to the primary clock occurs (see
Figure 3-2). When the clock switch is complete, the
T1RUN bit is cleared, the OSTS bit is set and the
primary clock is providing the clock. The IDLEN and
SCS bits are not affected by the wake-up; the Timer1
oscillator continues to run.
The Timer1 oscillator should already be
running prior to entering SEC_RUN mode.
If the T1OSCEN bit is not set when the
SCS1:SCS0 bits are set to ‘01’, entry to
SEC_RUN mode will not occur. If the
Timer1 oscillator is enabled, but not yet
running, device clocks will be delayed until
the oscillator has started. In such situations, initial oscillator operation is far from
stable and unpredictable operation may
result.
FIGURE 3-1:
TRANSITION TIMING FOR ENTRY TO SEC_RUN MODE
Q1 Q2 Q3 Q4 Q1
Q2
1
T1OSI
2
3
n-1
Q3
Q4
Q1
Q2
Q3
n
Clock Transition
OSC1
CPU
Clock
Peripheral
Clock
Program
Counter
PC
FIGURE 3-2:
PC + 2
PC + 4
TRANSITION TIMING FROM SEC_RUN MODE TO PRI_RUN MODE (HSPLL)
Q1
Q2
Q3
Q4
Q1
Q2 Q3 Q4 Q1 Q2 Q3
T1OSI
OSC1
TOST(1)
TPLL(1)
1
PLL Clock
Output
2
n-1 n
Clock
Transition
CPU Clock
Peripheral
Clock
Program
Counter
SCS1:SCS0 bits Changed
PC + 2
PC
PC + 4
OSTS bit Set
Note 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 39
PIC18F85J90 FAMILY
3.2.3
RC_RUN MODE
On transitions from RC_RUN mode to PRI_RUN mode,
the device continues to be clocked from the INTRC
while the primary clock is started. When the primary
clock becomes ready, a clock switch to the primary
clock occurs (see Figure 3-4). When the clock switch is
complete, the OSTS bit is set and the primary clock is
providing the device clock. The IDLEN and SCS bits
are not affected by the switch. The INTRC source will
continue to run if either the WDT or the Fail-Safe Clock
Monitor is enabled.
In RC_RUN mode, the CPU and peripherals are
clocked from the internal oscillator; the primary clock is
shut down. This mode provides the best power conservation of all the Run modes while still executing code.
It works well for user applications which are not highly
timing sensitive or do not require high-speed clocks at
all times.
This mode is entered by setting SCS bits to ‘11’. When
the clock source is switched to the INTRC (see
Figure 3-3), the primary oscillator is shut down and the
OSTS bit is cleared.
FIGURE 3-3:
TRANSITION TIMING TO RC_RUN MODE
Q1 Q2 Q3 Q4 Q1
Q2
1
INTRC
2
3
n-1
Q3
Q4
Q1
Q2
Q3
n
Clock Transition
OSC1
CPU
Clock
Peripheral
Clock
Program
Counter
PC
FIGURE 3-4:
PC + 2
PC + 4
TRANSITION TIMING FROM RC_RUN MODE TO PRI_RUN MODE
Q1
Q2
Q3
Q4
Q2 Q3 Q4 Q1 Q2 Q3
Q1
INTRC
OSC1
TOST(1)
TPLL(1)
1
PLL Clock
Output
2
n-1 n
Clock
Transition
CPU Clock
Peripheral
Clock
Program
Counter
SCS1:SCS0 bits Changed
PC + 2
PC
PC + 4
OSTS bit Set
Note 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.
DS39770B-page 40
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
3.3
Sleep Mode
3.4
The power-managed Sleep mode is identical to the legacy Sleep mode offered in all other PIC devices. It is
entered by clearing the IDLEN bit (the default state on
device Reset) and executing the SLEEP instruction.
This shuts down the selected oscillator (Figure 3-5). All
clock source status bits are cleared.
Idle Modes
The Idle modes allow the controller’s CPU to be
selectively shut down while the peripherals continue to
operate. Selecting a particular Idle mode allows users
to further manage power consumption.
If the IDLEN bit is set to a ‘1’ when a SLEEP instruction is
executed, the peripherals will be clocked from the clock
source selected using the SCS1:SCS0 bits; however, the
CPU will not be clocked. The clock source status bits are
not affected. Setting IDLEN and executing a SLEEP
instruction provides a quick method of switching from a
given Run mode to its corresponding Idle mode.
Entering the Sleep mode from any other mode does not
require a clock switch. This is because no clocks are
needed once the controller has entered Sleep. If the
WDT is selected, the INTRC source will continue to
operate. If the Timer1 oscillator is enabled, it will also
continue to run.
If the WDT is selected, the INTRC source will continue
to operate. If the Timer1 oscillator is enabled, it will also
continue to run.
When a wake event occurs in Sleep mode (by interrupt,
Reset or WDT time-out), the device will not be clocked
until the clock source selected by the SCS1:SCS0 bits
becomes ready (see Figure 3-6), or it will be clocked
from the internal oscillator if either the Two-Speed
Start-up or the Fail-Safe Clock Monitor are enabled
(see Section 22.0 “Special Features of the CPU”). In
either case, the OSTS bit is set when the primary clock
is providing the device clocks. The IDLEN and SCS bits
are not affected by the wake-up.
Since the CPU is not executing instructions, the only
exits from any of the Idle modes are by interrupt, WDT
time-out or a Reset. When a wake event occurs, CPU
execution is delayed by an interval of TCSD
(parameter 38, Table 25-11) while it becomes ready to
execute code. When the CPU begins executing code,
it resumes with the same clock source for the current
Idle mode. For example, when waking from RC_IDLE
mode, the internal oscillator block will clock the CPU
and peripherals (in other words, RC_RUN mode). The
IDLEN and SCS bits are not affected by the wake-up.
While in any Idle mode or the Sleep mode, a WDT
time-out will result in a WDT wake-up to the Run mode
currently specified by the SCS1:SCS0 bits.
FIGURE 3-5:
TRANSITION TIMING FOR ENTRY TO SLEEP MODE
Q1 Q2 Q3 Q4 Q1
OSC1
CPU
Clock
Peripheral
Clock
Sleep
Program
Counter
PC
FIGURE 3-6:
PC + 2
TRANSITION TIMING FOR WAKE FROM SLEEP (HSPLL)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Q1
OSC1
TOST(1)
PLL Clock
Output
TPLL(1)
CPU Clock
Peripheral
Clock
Program
Counter
PC + 2
PC
Wake Event
PC + 4
PC + 6
OSTS bit Set
Note 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 41
PIC18F85J90 FAMILY
3.4.1
PRI_IDLE MODE
3.4.2
This mode is unique among the three low-power Idle
modes, in that it does not disable the primary device
clock. For timing sensitive applications, this allows for
the fastest resumption of device operation with its more
accurate primary clock source, since the clock source
does not have to “warm up” or transition from another
oscillator.
PRI_IDLE mode is entered from PRI_RUN mode by
setting the IDLEN bit and executing a SLEEP instruction. If the device is in another Run mode, set IDLEN
first, then set the SCS bits to ‘10’ and execute SLEEP.
Although the CPU is disabled, the peripherals continue
to be clocked from the primary clock source specified
by the FOSC1:FOSC0 Configuration bits. The OSTS
bit remains set (see Figure 3-7).
In SEC_IDLE mode, the CPU is disabled but the
peripherals continue to be clocked from the Timer1
oscillator. This mode is entered from SEC_RUN by setting the IDLEN bit and executing a SLEEP instruction. If
the device is in another Run mode, set IDLEN first, then
set SCS1:SCS0 to ‘01’ and execute SLEEP. When the
clock source is switched to the Timer1 oscillator, the
primary oscillator is shut down, the OSTS bit is cleared
and the T1RUN bit is set.
When a wake event occurs, the peripherals continue to
be clocked from the Timer1 oscillator. After an interval
of TCSD following the wake event, the CPU begins executing code being clocked by the Timer1 oscillator. The
IDLEN and SCS bits are not affected by the wake-up;
the Timer1 oscillator continues to run (see Figure 3-8).
When a wake event occurs, the CPU is clocked from the
primary clock source. A delay of interval TCSD is
required between the wake event and when code execution starts. This is required to allow the CPU to
become ready to execute instructions. After the
wake-up, the OSTS bit remains set. The IDLEN and
SCS bits are not affected by the wake-up (see
Figure 3-8).
FIGURE 3-7:
SEC_IDLE MODE
Note:
The Timer1 oscillator should already be
running prior to entering SEC_IDLE mode.
If the T1OSCEN bit is not set when the
SLEEP instruction is executed, the SLEEP
instruction will be ignored and entry to
SEC_IDLE mode will not occur. If the
Timer1 oscillator is enabled, but not yet
running, peripheral clocks will be delayed
until the oscillator has started. In such
situations, initial oscillator operation is far
from stable and unpredictable operation
may result.
TRANSITION TIMING FOR ENTRY TO IDLE MODE
Q1
Q4
Q3
Q2
Q1
OSC1
CPU Clock
Peripheral
Clock
Program
Counter
FIGURE 3-8:
PC
PC + 2
TRANSITION TIMING FOR WAKE FROM IDLE TO RUN MODE
Q1
Q2
Q3
Q4
OSC1
TCSD
CPU Clock
Peripheral
Clock
Program
Counter
PC
Wake Event
DS39770B-page 42
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
3.4.3
RC_IDLE MODE
3.5.2
In RC_IDLE mode, the CPU is disabled but the peripherals continue to be clocked from the internal oscillator.
This mode allows for controllable power conservation
during Idle periods.
From RC_RUN, this mode is entered by setting the
IDLEN bit and executing a SLEEP instruction. If the
device is in another Run mode, first set IDLEN, then
clear the SCS bits and execute SLEEP. When the clock
source is switched to the INTRC, the primary oscillator
is shut down and the OSTS bit is cleared.
When a wake event occurs, the peripherals continue to
be clocked from the INTOSC. After a delay of TCSD
following the wake event, the CPU begins executing
code being clocked by the INTOSC. The IDLEN and
SCS bits are not affected by the wake-up. The INTOSC
source will continue to run if either the WDT or the
Fail-Safe Clock Monitor is enabled.
3.5
A WDT time-out will cause different actions depending
on which power-managed mode the device is in when
the time-out occurs.
If the device is not executing code (all Idle modes and
Sleep mode), the time-out will result in an exit from the
power-managed mode (see Section 3.2 “Run
Modes” and Section 3.3 “Sleep Mode”). If the device
is executing code (all Run modes), the time-out will
result in a WDT Reset (see Section 22.2 “Watchdog
Timer (WDT)”).
The Watchdog Timer and postscaler are cleared by one
of the following events:
• executing a SLEEP or CLRWDT instruction
• the loss of a currently selected clock source (if the
Fail-Safe Clock Monitor is enabled)
3.5.3
EXIT BY RESET
Exiting an Idle or Sleep mode by Reset automatically
forces the device to run from the INTRC.
Exiting Idle and Sleep Modes
An exit from Sleep mode, or any of the Idle modes, is
triggered by an interrupt, a Reset or a WDT time-out.
This section discusses the triggers that cause exits
from power-managed modes. The clocking subsystem
actions are discussed in each of the power-managed
mode sections (see Section 3.2 “Run Modes”,
Section 3.3 “Sleep Mode” and Section 3.4 “Idle
Modes”).
3.5.1
EXIT BY WDT TIME-OUT
EXIT BY INTERRUPT
Any of the available interrupt sources can cause the
device to exit from an Idle mode, or the Sleep mode, to
a Run mode. To enable this functionality, an interrupt
source must be enabled by setting its enable bit in one
of the INTCON or PIE registers. The exit sequence is
initiated when the corresponding interrupt flag bit is set.
On all exits from Idle or Sleep modes by interrupt, code
execution branches to the interrupt vector if the
GIE/GIEH bit (INTCON<7>) is set. Otherwise, code
execution continues or resumes without branching
(see Section 8.0 “Interrupts”).
3.5.4
EXIT WITHOUT AN OSCILLATOR
START-UP DELAY
Certain exits from power-managed modes do not
invoke the OST at all. There are two cases:
• PRI_IDLE mode, where the primary clock source
is not stopped; and
• the primary clock source is either the EC or
ECPLL mode.
In these instances, the primary clock source either
does not require an oscillator start-up delay, since it is
already running (PRI_IDLE), or normally does not
require an oscillator start-up delay (EC). However, a
fixed delay of interval TCSD following the wake event is
still required when leaving Sleep and Idle modes to
allow the CPU to prepare for execution. Instruction
execution resumes on the first clock cycle following this
delay.
A fixed delay of interval TCSD following the wake event
is required when leaving Sleep and Idle modes. This
delay is required for the CPU to prepare for execution.
Instruction execution resumes on the first clock cycle
following this delay.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 43
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 44
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
4.0
RESET
4.1
The PIC18F85J90 family of devices differentiate
between various kinds of Reset:
a)
b)
c)
d)
e)
f)
g)
h)
Power-on Reset (POR)
MCLR Reset during normal operation
MCLR Reset during power-managed modes
Watchdog Timer (WDT) Reset (during
execution)
Brown-out Reset (BOR)
RESET Instruction
Stack Full Reset
Stack Underflow Reset
RCON Register
Device Reset events are tracked through the RCON
register (Register 4-1). The lower five bits of the
register indicate that a specific Reset event has
occurred. In most cases, these bits can only be set by
the event and must be cleared by the application after
the event. The state of these flag bits, taken together,
can be read to indicate the type of Reset that just
occurred. This is described in more detail in
Section 4.6 “Reset State of Registers”.
The RCON register also has a control bit for setting
interrupt priority (IPEN). Interrupt priority is discussed
in Section 8.0 “Interrupts”.
This section discusses Resets generated by MCLR,
POR and BOR and covers the operation of the various
start-up timers. Stack Reset events are covered in
Section 5.1.4.4 “Stack Full and Underflow Resets”.
WDT Resets are covered in Section 22.2 “Watchdog
Timer (WDT)”.
A simplified block diagram of the on-chip Reset circuit
is shown in Figure 4-1.
FIGURE 4-1:
SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
RESET
Instruction
Stack
Pointer
Stack Full/Underflow Reset
External Reset
MCLR
( )_IDLE
Sleep
WDT
Time-out
VDD Rise
Detect
POR Pulse
VDD
Brown-out
Reset(1)
S
PWRT
32 μs
PWRT
INTRC
Note 1:
Chip_Reset
65.5 ms
R
11-bit Ripple Counter
Q
The ENVREG pin must be tied high to enable Brown-out Reset. The Brown-out Reset is provided by the on-chip
voltage regulator when there is insufficient source voltage to maintain regulation.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 45
PIC18F85J90 FAMILY
REGISTER 4-1:
RCON: RESET CONTROL REGISTER
R/W-0
U-0
U-0
R/W-1
R-1
R-1
R/W-0
R/W-0
IPEN
—
—
RI
TO
PD
POR
BOR
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (PIC16XXXX Compatibility mode)
bit 6-5
Unimplemented: Read as ‘0’
bit 4
RI: RESET Instruction Flag bit
1 = The RESET instruction was not executed (set by firmware only)
0 = The RESET instruction was executed causing a device Reset (must be set in software after a
Brown-out Reset occurs)
bit 3
TO: Watchdog Time-out Flag bit
1 = Set by power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
bit 2
PD: Power-Down Detection Flag bit
1 = Set by power-up or by the CLRWDT instruction
0 = Set by execution of the SLEEP instruction
bit 1
POR: Power-on Reset Status bit
1 = A Power-on Reset has not occurred (set by firmware only)
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
bit 0
BOR: Brown-out Reset Status bit
1 = A Brown-out Reset has not occurred (set by firmware only)
0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
Note 1: It is recommended that the POR bit be set after a Power-on Reset has been detected, so that subsequent
Power-on Resets may be detected.
2: If the on-chip voltage regulator is disabled, BOR remains ‘0’ at all times. See Section 4.4.1 “Detecting
BOR” for more information.
3: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming that POR was set to
‘1’ by software immediately after a Power-on Reset).
DS39770B-page 46
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
4.2
FIGURE 4-2:
Master Clear (MCLR)
The MCLR pin provides a method for triggering a hard
external Reset of the device. A Reset is generated by
holding the pin low. PIC18 extended microcontroller
devices have a noise filter in the MCLR Reset path
which detects and ignores small pulses.
4.3
D
R
R1
MCLR
C
Power-on Reset (POR)
A Power-on Reset condition is generated on-chip
whenever VDD rises above a certain threshold. This
allows the device to start in the initialized state when
VDD is adequate for operation.
When the device starts normal operation (i.e., exits the
Reset condition), device operating parameters
(voltage, frequency, temperature, etc.) must be met to
ensure operation. If these conditions are not met, the
device must be held in Reset until the operating
conditions are met.
Power-on Reset events are captured by the POR bit
(RCON<1>). The state of the bit is set to ‘0’ whenever
a Power-on Reset occurs; it does not change for any
other Reset event. POR is not reset to ‘1’ by any
hardware event. To capture multiple events, the user
manually resets the bit to ‘1’ in software following any
Power-on Reset.
Brown-out Reset (BOR)
The PIC18F85J90 family of devices incorporates a
simple BOR function when the internal regulator is
enabled (ENVREG pin is tied to VDD). The voltage regulator will trigger a Brown-out Reset when output of the
regulator to the device core approaches the voltage at
which the device is unable to run at full speed. The
BOR circuit also keeps the device in Reset as VDD
rises, until the regulator’s output level is sufficient for
full-speed operation.
PIC18F85J90
Note 1:
External Power-on Reset circuit is required
only if the VDD power-up slope is too slow.
The diode D helps discharge the capacitor
quickly when VDD powers down.
2:
R < 40 kΩ is recommended to make sure that
the voltage drop across R does not violate
the device’s electrical specification.
3:
R1 ≥ 1 kΩ will limit any current flowing into
MCLR from external capacitor C, in the event
of MCLR/VPP pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS).
To take advantage of the POR circuitry, tie the MCLR
pin through a resistor (1 kΩ to 10 kΩ) to VDD. This will
eliminate external RC components usually needed to
create a Power-on Reset delay. A minimum rise rate for
VDD is specified (parameter D004). For a slow rise
time, see Figure 4-2.
4.4
VDD
VDD
The MCLR pin is not driven low by any internal Resets,
including the WDT.
EXTERNAL POWER-ON
RESET CIRCUIT (FOR
SLOW VDD POWER-UP)
4.4.1
DETECTING BOR
The BOR bit always resets to ‘0’ on any Brown-out
Reset or Power-on Reset event. This makes it difficult
to determine if a Brown-out Reset event has occurred
just by reading the state of BOR alone. A more reliable
method is to simultaneously check the state of both
POR and BOR. This assumes that the POR bit is reset
to ‘1’ in software immediately after any Power-on Reset
event. If BOR is ‘0’ while POR is ‘1’, it can be reliably
assumed that a Brown-out Reset event has occurred.
If the voltage regulator is disabled, Brown-out Reset
functionality is disabled. In this case, the BOR bit
cannot be used to determine a Brown-out Reset event.
The BOR bit is still cleared by a Power-on Reset event.
Once a BOR has occurred, the Power-up Timer will
keep the chip in Reset for TPWRT (parameter 33). If
VDD drops below the threshold for full-speed operation
while the Power-up Timer is running, the chip will go
back into a Brown-out Reset and the Power-up Timer
will be initialized. Once VDD rises to the point where
regulator output is sufficient, the Power-up Timer will
execute the additional time delay.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 47
PIC18F85J90 FAMILY
4.5
4.5.1
Power-up Timer (PWRT)
PIC18F85J90 family devices incorporate an on-chip
Power-up Timer (PWRT) to help regulate the Power-on
Reset process. The PWRT is always enabled. The
main function is to ensure that the device voltage is
stable before code is executed.
The Power-up Timer (PWRT) of the PIC18F85J90 family devices is an 11-bit counter which uses the INTRC
source as the clock input. This yields an approximate
time interval of 2048 x 32 μs = 65.6 ms. While the
PWRT is counting, the device is held in Reset.
The power-up time delay depends on the INTRC clock
and will vary from chip-to-chip due to temperature and
process variation. See DC parameter 33 for details.
FIGURE 4-3:
TIME-OUT SEQUENCE
If enabled, the PWRT time-out is invoked after the POR
pulse has cleared. The total time-out will vary based on
the status of the PWRT. Figure 4-3, Figure 4-4,
Figure 4-5 and Figure 4-6 all depict time-out
sequences on power-up with the Power-up Timer
enabled.
Since the time-outs occur from the POR pulse, if MCLR
is kept low long enough, the PWRT will expire. Bringing
MCLR high will begin execution immediately
(Figure 4-5). This is useful for testing purposes, or to
synchronize more than one PIC18FXXXX device
operating in parallel.
TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD, VDD RISE < TPWRT)
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
INTERNAL RESET
FIGURE 4-4:
TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
INTERNAL RESET
DS39770B-page 48
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 4-5:
TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
INTERNAL RESET
FIGURE 4-6:
SLOW RISE TIME (MCLR TIED TO VDD, VDD RISE > TPWRT)
3.3V
VDD
0V
1V
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
INTERNAL RESET
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 49
PIC18F85J90 FAMILY
4.6
Reset State of Registers
Table 4-2 describes the Reset states for all of the
Special Function Registers. These are categorized by
Power-on and Brown-out Resets, Master Clear and
WDT Resets and WDT wake-ups.
Most registers are unaffected by a Reset. Their status
is unknown on POR and unchanged by all other
Resets. The other registers are forced to a “Reset
state” depending on the type of Reset that occurred.
Most registers are not affected by a WDT wake-up,
since this is viewed as the resumption of normal
operation. Status bits from the RCON register, RI, TO,
PD, POR and BOR, are set or cleared differently in
different Reset situations, as indicated in Table 4-1.
These bits are used in software to determine the nature
of the Reset.
TABLE 4-1:
STATUS BITS, THEIR SIGNIFICANCE AND THE INITIALIZATION CONDITION FOR
RCON REGISTER
RCON Register
STKPTR Register
Program
Counter(1)
RI
TO
PD
POR
BOR
STKFUL
STKUNF
Power-on Reset
0000h
1
1
1
0
0
0
0
RESET Instruction
0000h
0
u
u
u
u
u
u
Brown-out Reset
0000h
1
1
1
u
0
u
u
MCLR during power-managed
Run modes
0000h
u
1
u
u
u
u
u
MCLR during power-managed
Idle modes and Sleep mode
0000h
u
1
0
u
u
u
u
WDT time-out during full power
or power-managed Run modes
0000h
u
0
u
u
u
u
u
MCLR during full power
execution
0000h
u
u
u
u
u
u
u
Stack Full Reset (STVREN = 1)
0000h
u
u
u
u
u
1
u
Stack Underflow Reset
(STVREN = 1)
0000h
u
u
u
u
u
u
1
Stack Underflow Error (not an
actual Reset, STVREN = 0)
0000h
u
u
u
u
u
u
1
WDT time-out during
power-managed Idle or Sleep
modes
PC + 2
u
0
0
u
u
u
u
Interrupt exit from
power-managed modes
PC + 2
u
u
0
u
u
u
u
Condition
Legend: u = unchanged
Note 1: When the wake-up is due to an interrupt and the GIEH or GIEL bit is set, the PC is loaded with the
interrupt vector (0008h or 0018h).
DS39770B-page 50
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 4-2:
INITIALIZATION CONDITIONS FOR ALL REGISTERS
Applicable Devices
Power-on Reset,
Brown-out Reset
MCLR Resets
WDT Reset
RESET Instruction
Stack Resets
Wake-up via WDT
or Interrupt
TOSU
PIC18F6XJ90 PIC18F8XJ90
---0 0000
---0 0000
---0 uuuu(1)
TOSH
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu(1)
TOSL
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu(1)
STKPTR
PIC18F6XJ90 PIC18F8XJ90
uu-0 0000
00-0 0000
uu-u uuuu(1)
PCLATU
PIC18F6XJ90 PIC18F8XJ90
---0 0000
---0 0000
---u uuuu
PCLATH
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
PCL
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
PC + 2(2)
TBLPTRU
PIC18F6XJ90 PIC18F8XJ90
--00 0000
--00 0000
--uu uuuu
TBLPTRH
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
TBLPTRL
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
TABLAT
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
PRODH
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
PRODL
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
INTCON
PIC18F6XJ90 PIC18F8XJ90
0000 000x
0000 000u
uuuu uuuu(3)
INTCON2
PIC18F6XJ90 PIC18F8XJ90
1111 1111
1111 1111
uuuu uuuu(3)
INTCON3
PIC18F6XJ90 PIC18F8XJ90
1100 0000
1100 0000
uuuu uuuu(3)
INDF0
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
POSTINC0
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
POSTDEC0
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
PREINC0
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
Register
PLUSW0
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
FSR0H
PIC18F6XJ90 PIC18F8XJ90
---- xxxx
---- uuuu
---- uuuu
N/A
FSR0L
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
WREG
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
INDF1
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
POSTINC1
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
POSTDEC1
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
PREINC1
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
PLUSW1
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are
updated with the current value of the PC. The STKPTR is modified to point to the next location in the
hardware stack.
2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt
vector (0008h or 0018h).
3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
4: See Table 4-1 for Reset value for specific condition.
5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled depending on the oscillator mode selected. When
not enabled as PORTA pins, they are disabled and read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 51
PIC18F85J90 FAMILY
TABLE 4-2:
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Applicable Devices
Power-on Reset,
Brown-out Reset
MCLR Resets
WDT Reset
RESET Instruction
Stack Resets
Wake-up via WDT
or Interrupt
FSR1H
PIC18F6XJ90 PIC18F8XJ90
---- xxxx
---- uuuu
---- uuuu
FSR1L
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
BSR
PIC18F6XJ90 PIC18F8XJ90
---- 0000
---- 0000
---- uuuu
INDF2
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
POSTINC2
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
POSTDEC2
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
PREINC2
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
PLUSW2
PIC18F6XJ90 PIC18F8XJ90
N/A
N/A
N/A
FSR2H
PIC18F6XJ90 PIC18F8XJ90
---- xxxx
---- uuuu
---- uuuu
FSR2L
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
STATUS
PIC18F6XJ90 PIC18F8XJ90
---x xxxx
---u uuuu
---u uuuu
TMR0H
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
TMR0L
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
T0CON
PIC18F6XJ90 PIC18F8XJ90
1111 1111
1111 1111
uuuu uuuu
OSCCON
PIC18F6XJ90 PIC18F8XJ90
0100 q000
0100 q000
uuuu quuu
LCDREG
PIC18F6XJ90 PIC18F8XJ90
-011 1100
-011 1000
-uuu uuuu
WDTCON
PIC18F6XJ90 PIC18F8XJ90
0--- ---0
0--- ---0
u--- ---u
RCON(4)
PIC18F6XJ90 PIC18F8XJ90
0--1 11q0
0--q qquu
u--u qquu
TMR1H
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
TMR1L
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
T1CON
PIC18F6XJ90 PIC18F8XJ90
0000 0000
u0uu uuuu
uuuu uuuu
TMR2
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
PR2
PIC18F6XJ90 PIC18F8XJ90
1111 1111
1111 1111
1111 1111
T2CON
PIC18F6XJ90 PIC18F8XJ90
-000 0000
-000 0000
-uuu uuuu
SSPBUF
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
SSPADD
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
SSPSTAT
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
SSPCON1
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
SSPCON2
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
Register
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are
updated with the current value of the PC. The STKPTR is modified to point to the next location in the
hardware stack.
2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt
vector (0008h or 0018h).
3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
4: See Table 4-1 for Reset value for specific condition.
5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled depending on the oscillator mode selected. When
not enabled as PORTA pins, they are disabled and read as ‘0’.
DS39770B-page 52
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 4-2:
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Applicable Devices
Power-on Reset,
Brown-out Reset
MCLR Resets
WDT Reset
RESET Instruction
Stack Resets
Wake-up via WDT
or Interrupt
ADRESH
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
ADRESL
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
ADCON0
PIC18F6XJ90 PIC18F8XJ90
0-00 0000
0-00 0000
u-uu uuuu
ADCON1
PIC18F6XJ90 PIC18F8XJ90
--00 0000
--00 0000
--uu uuuu
ADCON2
PIC18F6XJ90 PIC18F8XJ90
0-00 0000
0-00 0000
u-uu uuuu
LCDDATA4
PIC18F6XJ90 PIC18F8XJ90
---- ---x
---- ---u
---- ---u
LCDDATA4
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA3
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA2
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA1
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA0
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDSE5
PIC18F6XJ90 PIC18F8XJ90
0000 0000
uuuu uuuu
uuuu uuuu
LCDSE4
PIC18F6XJ90 PIC18F8XJ90
---- ---0
---- ---u
---- ---u
Register
LCDSE4
PIC18F6XJ90 PIC18F8XJ90
0000 0000
uuuu uuuu
uuuu uuuu
LCDSE3
PIC18F6XJ90 PIC18F8XJ90
0000 0000
uuuu uuuu
uuuu uuuu
LCDSE2
PIC18F6XJ90 PIC18F8XJ90
0000 0000
uuuu uuuu
uuuu uuuu
LCDSE1
PIC18F6XJ90 PIC18F8XJ90
0000 0000
uuuu uuuu
uuuu uuuu
CVRCON
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
CMCON
PIC18F6XJ90 PIC18F8XJ90
0000 0111
0000 0111
uuuu uuuu
TMR3H
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
TMR3L
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
T3CON
PIC18F6XJ90 PIC18F8XJ90
0000 0000
uuuu uuuu
uuuu uuuu
SPBRG1
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
RCREG1
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
TXREG1
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
TXSTA1
PIC18F6XJ90 PIC18F8XJ90
0000 0010
0000 0010
uuuu uuuu
RCSTA1
PIC18F6XJ90 PIC18F8XJ90
0000 000x
0000 000x
uuuu uuuu
LCDPS
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
LCDSE0
PIC18F6XJ90 PIC18F8XJ90
0000 0000
uuuu uuuu
uuuu uuuu
LCDCON
PIC18F6XJ90 PIC18F8XJ90
000- 0000
000- 0000
uuu- uuuu
EECON2
PIC18F6XJ90 PIC18F8XJ90
---- ----
---- ----
---- ----
EECON1
PIC18F6XJ90 PIC18F8XJ90
---0 x00-
---0 u00-
---0 u00-
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are
updated with the current value of the PC. The STKPTR is modified to point to the next location in the
hardware stack.
2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt
vector (0008h or 0018h).
3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
4: See Table 4-1 for Reset value for specific condition.
5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled depending on the oscillator mode selected. When
not enabled as PORTA pins, they are disabled and read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 53
PIC18F85J90 FAMILY
TABLE 4-2:
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Register
Applicable Devices
Power-on Reset,
Brown-out Reset
MCLR Resets
WDT Reset
RESET Instruction
Stack Resets
Wake-up via WDT
or Interrupt
IPR3
PIC18F6XJ90 PIC18F8XJ90
-111 -11-
-111 -11-
-uuu -uu-
PIR3
PIC18F6XJ90 PIC18F8XJ90
-000 -00-
-000 -00-
-uuu -00-(3)
PIE3
PIC18F6XJ90 PIC18F8XJ90
-000 -00-
-000 -00-
-uuu -00-
IPR2
PIC18F6XJ90 PIC18F8XJ90
11-- 111-
11-- 111-
uu-- uuu-
PIR2
PIC18F6XJ90 PIC18F8XJ90
00-- 000-
00-- 000-
uu-- uuu-(3)
PIE2
PIC18F6XJ90 PIC18F8XJ90
00-- 000-
00-- 000-
uu-- uuu-
IPR1
PIC18F6XJ90 PIC18F8XJ90
-111 1-11
-111 1-11
-uuu u-uu
PIR1
PIC18F6XJ90 PIC18F8XJ90
-000 0-00
-000 0-00
-uuu u-uu(3)
PIE1
PIC18F6XJ90 PIC18F8XJ90
-000 0-00
-000 0-00
-uuu u-uu
OSCTUNE
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
TRISJ
PIC18F6XJ90 PIC18F8XJ90
1111 1111
1111 1111
uuuu uuuu
TRISH
PIC18F6XJ90 PIC18F8XJ90
1111 1111
1111 1111
uuuu uuuu
TRISG
PIC18F6XJ90 PIC18F8XJ90
0001 1111
0001 1111
uuuu uuuu
TRISF
PIC18F6XJ90 PIC18F8XJ90
1111 111-
1111 111-
uuuu uuu-
TRISE
PIC18F6XJ90 PIC18F8XJ90
1111 1-11
1111 1-11
uuuu u-uu
TRISD
PIC18F6XJ90 PIC18F8XJ90
1111 1111
1111 1111
uuuu uuuu
TRISC
PIC18F6XJ90 PIC18F8XJ90
1111 1111
1111 1111
uuuu uuuu
TRISB
PIC18F6XJ90 PIC18F8XJ90
1111 1111
1111 1111
uuuu uuuu
(5)
1111(5)
1111(5)
uuuu uuuu(5)
TRISA
PIC18F6XJ90 PIC18F8XJ90
1111
LATJ
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LATH
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LATG
PIC18F6XJ90 PIC18F8XJ90
00-x xxxx
00-u uuuu
uu-u uuuu
LATF
PIC18F6XJ90 PIC18F8XJ90
xxxx xxx-
uuuu uuu-
uuuu uuu-
LATE
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LATD
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LATC
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LATB
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LATA(5)
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx(5)
uuuu uuuu(5)
uuuu uuuu(5)
PORTJ
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
PORTH
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
PORTG
PIC18F6XJ90 PIC18F8XJ90
000x xxxx
000u uuuu
000u uuuu
PORTF
PIC18F6XJ90 PIC18F8XJ90
xxxx xxx-
uuuu uuu-
uuuu uuu-
1111
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are
updated with the current value of the PC. The STKPTR is modified to point to the next location in the
hardware stack.
2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt
vector (0008h or 0018h).
3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
4: See Table 4-1 for Reset value for specific condition.
5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled depending on the oscillator mode selected. When
not enabled as PORTA pins, they are disabled and read as ‘0’.
DS39770B-page 54
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 4-2:
Register
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Applicable Devices
Power-on Reset,
Brown-out Reset
MCLR Resets
WDT Reset
RESET Instruction
Stack Resets
Wake-up via WDT
or Interrupt
PORTE
PIC18F6XJ90 PIC18F8XJ90
xxxx x-xx
uuuu u-uu
uuuu u-uu
PORTD
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
PORTC
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
PORTB
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
(5)
(5)
(5)
uuuu uuuu(5)
PORTA
PIC18F6XJ90 PIC18F8XJ90
xx0x 0000
uu0u 0000
SPBRGH1
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
BAUDCON1
PIC18F6XJ90 PIC18F8XJ90
01-0 0-00
01-0 0-00
uu-u u-uu
LCDDATA23
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA22
PIC18F6XJ90 PIC18F8XJ90
---- ---x
---- ---u
---- ---u
LCDDATA22
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA21
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA20
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA19
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA18
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA17
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA16
PIC18F6XJ90 PIC18F8XJ90
---- ---x
---- ---u
---- ---u
LCDDATA16
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA15
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA14
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA13
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA12
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA11
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA10
PIC18F6XJ90 PIC18F8XJ90
---- ---x
---- ---u
---- ---u
LCDDATA10
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA9
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA8
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA7
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA6
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA5
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
CCPR1H
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
CCPR1L
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
CCP1CON
PIC18F6XJ90 PIC18F8XJ90
--00 0000
--00 0000
--uu uuuu
CCPR2H
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are
updated with the current value of the PC. The STKPTR is modified to point to the next location in the
hardware stack.
2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt
vector (0008h or 0018h).
3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
4: See Table 4-1 for Reset value for specific condition.
5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled depending on the oscillator mode selected. When
not enabled as PORTA pins, they are disabled and read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 55
PIC18F85J90 FAMILY
TABLE 4-2:
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Applicable Devices
Power-on Reset,
Brown-out Reset
MCLR Resets
WDT Reset
RESET Instruction
Stack Resets
Wake-up via WDT
or Interrupt
CCPR2L
PIC18F6XJ90 PIC18F8XJ90
xxxx xxxx
uuuu uuuu
uuuu uuuu
CCP2CON
PIC18F6XJ90 PIC18F8XJ90
--00 0000
--00 0000
--uu uuuu
SPBRG2
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
RCREG2
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
TXREG2
PIC18F6XJ90 PIC18F8XJ90
0000 0000
0000 0000
uuuu uuuu
TXSTA2
PIC18F6XJ90 PIC18F8XJ90
0000 -010
0000 -010
uuuu -uuu
RCSTA2
PIC18F6XJ90 PIC18F8XJ90
0000 000x
0000 000x
uuuu uuuu
Register
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are
updated with the current value of the PC. The STKPTR is modified to point to the next location in the
hardware stack.
2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt
vector (0008h or 0018h).
3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
4: See Table 4-1 for Reset value for specific condition.
5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled depending on the oscillator mode selected. When
not enabled as PORTA pins, they are disabled and read as ‘0’.
DS39770B-page 56
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
5.0
MEMORY ORGANIZATION
5.1
There are two types of memory in PIC18 Flash
microcontroller devices:
• Program Memory
• Data RAM
As Harvard architecture devices, the data and program
memories use separate busses; this allows for
concurrent access of the two memory spaces.
Additional detailed information on the operation of the
Flash program memory is provided in Section 6.0
“Flash Program Memory”.
FIGURE 5-1:
Program Memory Organization
PIC18 microcontrollers implement a 21-bit program
counter which is capable of addressing a 2-Mbyte
program memory space. Accessing a location between
the upper boundary of the physically implemented
memory and the 2-Mbyte address will return all ‘0’s (a
NOP instruction).
The entire PIC18F85J90 family offers a range of
on-chip Flash program memory sizes, from 8 Kbytes
(up to 4,096 single-word instructions) to 32 Kbytes
(32,768 single-word instructions). The program
memory maps for individual family members are shown
in Figure 5-1.
MEMORY MAPS FOR PIC18F85J90 FAMILY DEVICES
PC<20:0>
CALL, CALLW, RCALL,
RETURN, RETFIE, RETLW,
ADDULNK, SUBULNK
21
Stack Level 1
••
•
Stack Level 31
PIC18FX4J90
On-Chip
Memory
PIC18FX5J90
On-Chip
Memory
Config. Words
000000h
001FFFh
Config. Words
003FFFh
Config. Words
Unimplemented
Unimplemented
Unimplemented
Read as ‘0’
Read as ‘0’
Read as ‘0’
User Memory Space
PIC18FX3J90
On-Chip
Memory
007FFFh
1FFFFFh
Note:
Sizes of memory areas are not to scale. Sizes of program memory areas are enhanced to show detail.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 57
PIC18F85J90 FAMILY
5.1.1
5.1.2
HARD MEMORY VECTORS
FLASH CONFIGURATION WORDS
All PIC18 devices have a total of three hard-coded
return vectors in their program memory space. The
Reset vector address is the default value to which the
program counter returns on all device Resets; it is
located at 0000h.
Because PIC18F85J90 family devices do not have persistent configuration memory, the top four words of
on-chip program memory are reserved for configuration
information. On Reset, the configuration information is
copied into the Configuration registers.
PIC18 devices also have two interrupt vector
addresses for the handling of high priority and low
priority interrupts. The high priority interrupt vector is
located at 0008h and the low priority interrupt vector is
at 0018h. Their locations in relation to the program
memory map are shown in Figure 5-2.
The Configuration Words are stored in their program
memory location in numerical order, starting with the
lower byte of CONFIG1 at the lowest address and ending with the upper byte of CONFIG4. For these devices,
only Configuration Words, CONFIG1 through
CONFIG3, are used; CONFIG4 is reserved. The actual
addresses of the Flash Configuration Word for devices
in the PIC18F85J90 family are shown in Table 5-1.
Their location in the memory map is shown with the
other memory vectors in Figure 5-2.
FIGURE 5-2:
HARD VECTOR AND
CONFIGURATION WORD
LOCATIONS FOR
PIC18F85J90 FAMILY
FAMILY DEVICES
Reset Vector
0000h
High Priority Interrupt Vector
0008h
Low Priority Interrupt Vector
0018h
Additional details on the device Configuration Words
are provided in Section 22.1 “Configuration Bits”.
TABLE 5-1:
Device
PIC18F63J90
On-Chip
Program Memory
PIC18F83J90
PIC18F64J90
PIC18F84J90
PIC18F65J90
PIC18F85J90
Flash Configuration Words
FLASH CONFIGURATION
WORD FOR PIC18F85J90
FAMILY DEVICES
Program
Memory
(Kbytes)
Configuration
Word
Addresses
8
1FF8h to 1FFFh
16
3FF8h to 3FFFh
32
7FF8h to 7FFFh
(Top of Memory-7)
(Top of Memory)
Read ‘0’
1FFFFFh
Legend:
(Top of Memory) represents upper boundary
of on-chip program memory space (see
Figure 5-1 for device-specific values).
Shaded area represents unimplemented
memory. Areas are not shown to scale.
DS39770B-page 58
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
5.1.3
PROGRAM COUNTER
The Program Counter (PC) specifies the address of the
instruction to fetch for execution. The PC is 21 bits wide
and is contained in three separate 8-bit registers. The
low byte, known as the PCL register, is both readable
and writable. The high byte, or PCH register, contains
the PC<15:8> bits; it is not directly readable or writable.
Updates to the PCH register are performed through the
PCLATH register. The upper byte is called PCU. This
register contains the PC<20:16> bits; it is also not
directly readable or writable. Updates to the PCU
register are performed through the PCLATU register.
The contents of PCLATH and PCLATU are transferred
to the program counter by any operation that writes
PCL. Similarly, the upper two bytes of the program
counter are transferred to PCLATH and PCLATU by an
operation that reads PCL. This is useful for computed
offsets to the PC (see Section 5.1.6.1 “Computed
GOTO”).
The PC addresses bytes in the program memory. To
prevent the PC from becoming misaligned with word
instructions, the Least Significant bit of PCL is fixed to
a value of ‘0’. The PC increments by 2 to address
sequential instructions in the program memory.
The CALL, RCALL, GOTO and program branch
instructions write to the program counter directly. For
these instructions, the contents of PCLATH and
PCLATU are not transferred to the program counter.
5.1.4
RETURN ADDRESS STACK
The return address stack allows any combination of up
to 31 program calls and interrupts to occur. The PC is
pushed onto the stack when a CALL or RCALL instruction is executed, or an interrupt is Acknowledged. The
PC value is pulled off the stack on a RETURN, RETLW
or a RETFIE instruction (and on ADDULNK and
SUBULNK instructions if the extended instruction set is
enabled). PCLATU and PCLATH are not affected by
any of the RETURN or CALL instructions.
FIGURE 5-3:
The stack operates as a 31-word by 21-bit RAM and a
5-bit Stack Pointer, STKPTR. The stack space is not
part of either program or data space. The Stack Pointer
is readable and writable and the address on the top of
the stack is readable and writable through the
Top-of-Stack Special Function Registers. Data can also
be pushed to, or popped from the stack, using these
registers.
A CALL type instruction causes a push onto the stack.
The Stack Pointer is first incremented and the location
pointed to by the Stack Pointer is written with the
contents of the PC (already pointing to the instruction
following the CALL). A RETURN type instruction causes
a pop from the stack. The contents of the location
pointed to by the STKPTR are transferred to the PC
and then the Stack Pointer is decremented.
The Stack Pointer is initialized to ‘00000’ after all
Resets. There is no RAM associated with the location
corresponding to a Stack Pointer value of ‘00000’; this
is only a Reset value. Status bits indicate if the stack is
full, has overflowed or has underflowed.
5.1.4.1
Top-of-Stack Access
Only the top of the return address stack (TOS) is
readable and writable. A set of three registers,
TOSU:TOSH:TOSL, holds the contents of the stack
location pointed to by the STKPTR register
(Figure 5-3). This allows users to implement a software
stack if necessary. After a CALL, RCALL or interrupt
(and ADDULNK and SUBULNK instructions if the
extended instruction set is enabled), the software can
read
the
pushed
value
by
reading
the
TOSU:TOSH:TOSL registers. These values can be
placed on a user-defined software stack. At return time,
the software can return these values to
TOSU:TOSH:TOSL and do a return.
The user must disable the global interrupt enable bits
while accessing the stack to prevent inadvertent stack
corruption.
RETURN ADDRESS STACK AND ASSOCIATED REGISTERS
Return Address Stack <20:0>
Top-of-Stack Registers
TOSU
00h
TOSH
1Ah
11111
11110
11101
TOSL
34h
Top-of-Stack
© 2007 Microchip Technology Inc.
001A34h
000D58h
Preliminary
Stack Pointer
STKPTR<4:0>
00010
00011
00010
00001
00000
DS39770B-page 59
PIC18F85J90 FAMILY
5.1.4.2
Return Stack Pointer (STKPTR)
The STKPTR register (Register 5-1) contains the Stack
Pointer value, the STKFUL (Stack Full) status bit and
the STKUNF (Stack Underflow) status bits. The value
of the Stack Pointer can be 0 through 31. The Stack
Pointer increments before values are pushed onto the
stack and decrements after values are popped off the
stack. On Reset, the Stack Pointer value will be zero.
The user may read and write the Stack Pointer value.
This feature can be used by a Real-Time Operating
System (RTOS) for return stack maintenance.
After the PC is pushed onto the stack 31 times (without
popping any values off the stack), the STKFUL bit is
set. The STKFUL bit is cleared by software or by a
POR.
The action that takes place when the stack becomes
full depends on the state of the STVREN (Stack Overflow Reset Enable) Configuration bit. (Refer to
Section 22.1 “Configuration Bits” for a description of
the device Configuration bits.) If STVREN is set
(default), the 31st push will push the (PC + 2) value
onto the stack, set the STKFUL bit and reset the
device. The STKFUL bit will remain set and the Stack
Pointer will be set to zero.
If STVREN is cleared, the STKFUL bit will be set on the
31st push and the Stack Pointer will increment to 31.
Any additional pushes will not overwrite the 31st push
and the STKPTR will remain at 31.
REGISTER 5-1:
When the stack has been popped enough times to
unload the stack, the next pop will return a value of zero
to the PC and set the STKUNF bit, while the Stack
Pointer remains at zero. The STKUNF bit will remain
set until cleared by software or until a POR occurs.
Note:
5.1.4.3
Returning a value of zero to the PC on an
underflow has the effect of vectoring the
program to the Reset vector, where the
stack conditions can be verified and
appropriate actions can be taken. This is
not the same as a Reset, as the contents
of the SFRs are not affected.
PUSH and POP Instructions
Since the Top-of-Stack is readable and writable, the
ability to push values onto the stack and pull values off
the stack, without disturbing normal program execution, is a desirable feature. The PIC18 instruction set
includes two instructions, PUSH and POP, that permit
the TOS to be manipulated under software control.
TOSU, TOSH and TOSL can be modified to place data
or a return address on the stack.
The PUSH instruction places the current PC value onto
the stack. This increments the Stack Pointer and loads
the current PC value onto the stack.
The POP instruction discards the current TOS by
decrementing the Stack Pointer. The previous value
pushed onto the stack then becomes the TOS value.
STKPTR: STACK POINTER REGISTER
R/C-0
R/C-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STKFUL(1)
STKUNF(1)
—
SP4
SP3
SP2
SP1
SP0
bit 7
bit 0
Legend:
C = Clearable-only bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
STKFUL: Stack Full Flag bit(1)
1 = Stack became full or overflowed
0 = Stack has not become full or overflowed
bit 6
STKUNF: Stack Underflow Flag bit(1)
1 = Stack underflow occurred
0 = Stack underflow did not occur
bit 5
Unimplemented: Read as ‘0’
bit 4-0
SP4:SP0: Stack Pointer Location bits
Note 1:
x = Bit is unknown
Bit 7 and bit 6 are cleared by user software or by a POR.
DS39770B-page 60
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
5.1.4.4
Stack Full and Underflow Resets
5.1.6
Device Resets on stack overflow and stack underflow
conditions are enabled by setting the STVREN bit in
Configuration Register 1L. When STVREN is set, a full
or underflow condition will set the appropriate STKFUL
or STKUNF bit and then cause a device Reset. When
STVREN is cleared, a full or underflow condition will set
the appropriate STKFUL or STKUNF bit, but not cause
a device Reset. The STKFUL or STKUNF bits are
cleared by the user software or a Power-on Reset.
5.1.5
FAST REGISTER STACK
A Fast Register Stack is provided for the STATUS,
WREG and BSR registers to provide a “fast return”
option for interrupts. This stack is only one level deep
and is neither readable nor writable. It is loaded with the
current value of the corresponding register when the
processor vectors for an interrupt. All interrupt sources
will push values into the Stack registers. The values in
the registers are then loaded back into the working
registers if the RETFIE, FAST instruction is used to
return from the interrupt.
LOOK-UP TABLES IN PROGRAM
MEMORY
There may be programming situations that require the
creation of data structures, or look-up tables, in
program memory. For PIC18 devices, look-up tables
can be implemented in two ways:
• Computed GOTO
• Table Reads
5.1.6.1
Computed GOTO
A computed GOTO is accomplished by adding an offset
to the program counter. An example is shown in
Example 5-2.
A look-up table can be formed with an ADDWF PCL
instruction and a group of RETLW nn instructions. The
W register is loaded with an offset into the table before
executing a call to that table. The first instruction of the
called routine is the ADDWF PCL instruction. The next
instruction executed will be one of the RETLW nn
instructions that returns the value ‘nn’ to the calling
function.
If both low and high priority interrupts are enabled, the
Stack registers cannot be used reliably to return from
low priority interrupts. If a high priority interrupt occurs
while servicing a low priority interrupt, the Stack
register values stored by the low priority interrupt will be
overwritten. In these cases, users must save the key
registers in software during a low priority interrupt.
The offset value (in WREG) specifies the number of
bytes that the program counter should advance and
should be multiples of 2 (LSb = 0).
If interrupt priority is not used, all interrupts may use the
Fast Register Stack for returns from interrupt. If no
interrupts are used, the Fast Register Stack can be
used to restore the STATUS, WREG and BSR registers
at the end of a subroutine call. To use the Fast Register
Stack for a subroutine call, a CALL label, FAST
instruction must be executed to save the STATUS,
WREG and BSR registers to the Fast Register Stack. A
RETURN, FAST instruction is then executed to restore
these registers from the Fast Register Stack.
EXAMPLE 5-2:
Example 5-1 shows a source code example that uses
the Fast Register Stack during a subroutine call and
return.
EXAMPLE 5-1:
CALL SUB1, FAST
FAST REGISTER STACK
CODE EXAMPLE
;STATUS, WREG, BSR
;SAVED IN FAST REGISTER
;STACK
•
•
•
•
RETURN FAST
SUB1
;RESTORE VALUES SAVED
;IN FAST REGISTER STACK
© 2007 Microchip Technology Inc.
In this method, only one data byte may be stored in
each instruction location and room on the return
address stack is required.
ORG
TABLE
5.1.6.2
MOVF
CALL
nn00h
ADDWF
RETLW
RETLW
RETLW
.
.
.
COMPUTED GOTO USING
AN OFFSET VALUE
OFFSET, W
TABLE
PCL
nnh
nnh
nnh
Table Reads
A better method of storing data in program memory
allows two bytes of data to be stored in each instruction
location.
Look-up table data may be stored two bytes per
program word while programming. The Table Pointer
(TBLPTR) specifies the byte address and the Table
Latch (TABLAT) contains the data that is read from the
program memory. Data is transferred from program
memory one byte at a time.
Table read operation is discussed further
Section 6.1 “Table Reads and Table Writes”.
Preliminary
in
DS39770B-page 61
PIC18F85J90 FAMILY
5.2
5.2.2
PIC18 Instruction Cycle
5.2.1
An “Instruction Cycle” consists of four Q cycles, Q1
through Q4. The instruction fetch and execute are pipelined in such a manner that a fetch takes one instruction
cycle, while the decode and execute take another
instruction cycle. However, due to the pipelining, each
instruction effectively executes in one cycle. If an
instruction causes the program counter to change (e.g.,
GOTO), then two cycles are required to complete the
instruction (Example 5-3).
CLOCKING SCHEME
The microcontroller clock input, whether from an
internal or external source, is internally divided by four
to generate four non-overlapping quadrature clocks
(Q1, Q2, Q3 and Q4). Internally, the program counter is
incremented on every Q1; the instruction is fetched
from the program memory and latched into the
Instruction Register (IR) during Q4. The instruction is
decoded and executed during the following Q1 through
Q4. The clocks and instruction execution flow are
shown in Figure 5-4.
FIGURE 5-4:
INSTRUCTION FLOW/PIPELINING
A fetch cycle begins with the Program Counter (PC)
incrementing in Q1.
In the execution cycle, the fetched instruction is latched
into the Instruction Register (IR) in cycle Q1. This
instruction is then decoded and executed during the
Q2, Q3 and Q4 cycles. Data memory is read during Q2
(operand read) and written during Q4 (destination
write).
CLOCK/INSTRUCTION CYCLE
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
OSC1
Q1
Q2
Internal
Phase
Clock
Q3
Q4
PC
PC
PC + 2
PC + 4
OSC2/CLKO
(RC mode)
Execute INST (PC – 2)
Fetch INST (PC)
EXAMPLE 5-3:
1. MOVLW 55h
4. BSF
Execute INST (PC + 2)
Fetch INST (PC + 4)
INSTRUCTION PIPELINE FLOW
TCY0
TCY1
Fetch 1
Execute 1
2. MOVWF PORTB
3. BRA
Execute INST (PC)
Fetch INST (PC + 2)
SUB_1
Fetch 2
TCY2
TCY3
TCY4
TCY5
Execute 2
Fetch 3
Execute 3
Fetch 4
PORTA, BIT3 (Forced NOP)
Flush (NOP)
Fetch SUB_1 Execute SUB_1
5. Instruction @ address SUB_1
All instructions are single cycle, except for any program branches. These take two cycles since the fetch instruction
is “flushed” from the pipeline while the new instruction is being fetched and then executed.
DS39770B-page 62
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
5.2.3
INSTRUCTIONS IN PROGRAM
MEMORY
The program memory is addressed in bytes. Instructions are stored as two bytes or four bytes in program
memory. The Least Significant Byte of an instruction
word is always stored in a program memory location
with an even address (LSB = 0). To maintain alignment
with instruction boundaries, the PC increments in steps
of 2 and the LSB will always read ‘0’ (see Section 5.1.3
“Program Counter”).
Figure 5-5 shows an example of how instruction words
are stored in the program memory.
FIGURE 5-5:
The CALL and GOTO instructions have the absolute
program memory address embedded into the instruction. Since instructions are always stored on word
boundaries, the data contained in the instruction is a
word address. The word address is written to PC<20:1>
which accesses the desired byte address in program
memory. Instruction #2 in Figure 5-5 shows how the
instruction, GOTO 0006h, is encoded in the program
memory. Program branch instructions, which encode a
relative address offset, operate in the same manner. The
offset value stored in a branch instruction represents the
number of single-word instructions that the PC will be
offset by. Section 23.0 “Instruction Set Summary”
provides further details of the instruction set.
INSTRUCTIONS IN PROGRAM MEMORY
LSB = 1
LSB = 0
0Fh
EFh
F0h
C1h
F4h
55h
03h
00h
23h
56h
Program Memory
Byte Locations →
5.2.4
Instruction 1:
Instruction 2:
MOVLW
GOTO
055h
0006h
Instruction 3:
MOVFF
123h, 456h
TWO-WORD INSTRUCTIONS
The standard PIC18 instruction set has four two-word
instructions: CALL, MOVFF, GOTO and LSFR. In all
cases, the second word of the instructions always has
‘1111’ as its four Most Significant bits; the other 12 bits
are literal data, usually a data memory address.
The use of ‘1111’ in the 4 MSbs of an instruction
specifies a special form of NOP. If the instruction is
executed in proper sequence – immediately after the
first word – the data in the second word is accessed
EXAMPLE 5-4:
Word Address
↓
000000h
000002h
000004h
000006h
000008h
00000Ah
00000Ch
00000Eh
000010h
000012h
000014h
and used by the instruction sequence. If the first word
is skipped for some reason and the second word is
executed by itself, a NOP is executed instead. This is
necessary for cases when the two-word instruction is
preceded by a conditional instruction that changes the
PC. Example 5-4 shows how this works.
Note:
See Section 5.5 “Program Memory and
the Extended Instruction Set” for
information on two-word instructions in the
extended instruction set.
TWO-WORD INSTRUCTIONS
CASE 1:
Object Code
Source Code
0110 0110 0000 0000
TSTFSZ
REG1
; is RAM location 0?
1100 0001 0010 0011
MOVFF
REG1, REG2
; No, skip this word
ADDWF
REG3
; continue code
1111 0100 0101 0110
0010 0100 0000 0000
; Execute this word as a NOP
CASE 2:
Object Code
Source Code
0110 0110 0000 0000
TSTFSZ
REG1
; is RAM location 0?
1100 0001 0010 0011
MOVFF
REG1, REG2
; Yes, execute this word
ADDWF
REG3
1111 0100 0101 0110
0010 0100 0000 0000
© 2007 Microchip Technology Inc.
; 2nd word of instruction
; continue code
Preliminary
DS39770B-page 63
PIC18F85J90 FAMILY
5.3
Note:
5.3.1
Data Memory Organization
The operation of some aspects of data
memory are changed when the PIC18
extended instruction set is enabled. See
Section 5.6 “Data Memory and the
Extended Instruction Set” for more
information.
The data memory in PIC18 devices is implemented as
static RAM. Each register in the data memory has a
12-bit address, allowing up to 4096 bytes of data
memory. The memory space is divided into as many as
16 banks that contain 256 bytes each. The
PIC18FX3J90/X4J90 devices, with up to 16 Kbytes of
program memory, implement 4 complete banks for a
total of 1024 bytes. PIC18FX5J90 devices, with
32 Kbytes of program memory, implement 8 complete
banks for a total of 2048 bytes. Figure 5-6 and
Figure 5-7 show the data memory organization for the
devices.
The data memory contains Special Function Registers
(SFRs) and General Purpose Registers (GPRs). The
SFRs are used for control and status of the controller
and peripheral functions, while GPRs are used for data
storage and scratchpad operations in the user’s
application. Any read of an unimplemented location will
read as ‘0’s.
BANK SELECT REGISTER
Large areas of data memory require an efficient
addressing scheme to make rapid access to any
address possible. Ideally, this means that an entire
address does not need to be provided for each read or
write operation. For PIC18 devices, this is accomplished with a RAM banking scheme. This divides the
memory space into 16 contiguous banks of 256 bytes.
Depending on the instruction, each location can be
addressed directly by its full 12-bit address, or an 8-bit
low-order address and a 4-bit Bank Pointer.
Most instructions in the PIC18 instruction set make use
of the Bank Pointer, known as the Bank Select Register
(BSR). This SFR holds the 4 Most Significant bits of a
location’s address; the instruction itself includes the
8 Least Significant bits. Only the four lower bits of the
BSR are implemented (BSR3:BSR0). The upper four
bits are unused; they will always read ‘0’ and cannot be
written to. The BSR can be loaded directly by using the
MOVLB instruction.
The value of the BSR indicates the bank in data
memory. The 8 bits in the instruction show the location
in the bank and can be thought of as an offset from the
bank’s lower boundary. The relationship between the
BSR’s value and the bank division in data memory is
shown in Figure 5-8.
The instruction set and architecture allow operations
across all banks. The entire data memory may be
accessed by Direct, Indirect or Indexed Addressing
modes. Addressing modes are discussed later in this
section.
Since up to 16 registers may share the same low-order
address, the user must always be careful to ensure that
the proper bank is selected before performing a data
read or write. For example, writing what should be
program data to an 8-bit address of F9h while the BSR
is 0Fh, will end up resetting the program counter.
To ensure that commonly used registers (select SFRs
and select GPRs) can be accessed in a single cycle,
PIC18 devices implement an Access Bank. This is a
256-byte memory space that provides fast access to
select SFRs and the lower portion of GPR Bank 0 without using the BSR. Section 5.3.2 “Access Bank”
provides a detailed description of the Access RAM.
While any bank can be selected, only those banks that
are actually implemented can be read or written to.
Writes to unimplemented banks are ignored, while
reads from unimplemented banks will return ‘0’s. Even
so, the STATUS register will still be affected as if the
operation was successful. The data memory map in
Figure 5-6 indicates which banks are implemented.
In the core PIC18 instruction set, only the MOVFF
instruction fully specifies the 12-bit address of the
source and target registers. This instruction ignores the
BSR completely when it executes. All other instructions
include only the low-order address as an operand and
must use either the BSR or the Access Bank to locate
their target registers.
DS39770B-page 64
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 5-6:
DATA MEMORY MAP FOR PIC18FX3J90/X4J90 DEVICES
When a = 0:
BSR<3:0>
Data Memory Map
00h
= 0000
= 0001
= 0010
= 0011
Access RAM
Bank 0
FFh
00h
Bank 1
GPR
000h
05Fh
060h
0FFh
100h
GPR
1FFh
200h
FFh
00h
Bank 2
GPR
FFh
00h
Bank 3
2FFh
300h
The first 96 bytes are general
purpose RAM (from Bank 0).
The second 160 bytes are
Special Function Registers
(from Bank 15).
When a = 1:
The BSR specifies the bank
used by the instruction.
GPR
3FFh
400h
FFh
00h
= 0100
The BSR is ignored and the
Access Bank is used.
Bank 4
Access Bank
00h
Access RAM Low
to
= 1110
5Fh
Access RAM High 60h
(SFRs)
FFh
Unused
Read as ‘0’
Bank 14
= 1111
FFh
00h
Unused
FFh
SFR
Bank 15
© 2007 Microchip Technology Inc.
EFFh
F00h
F5Fh
F60h
FFFh
Preliminary
DS39770B-page 65
PIC18F85J90 FAMILY
FIGURE 5-7:
DATA MEMORY MAP FOR PIC18FX5J90 DEVICES
When a = 0:
BSR<3:0>
Data Memory Map
00h
= 0000
= 0001
= 0010
= 0011
= 0100
= 0101
= 0110
= 0111
Access RAM
Bank 0
FFh
00h
Bank 1
GPR
Bank 2
1FFh
200h
GPR
FFh
00h
Bank 3
2FFh
300h
Bank 4
The second 160 bytes are
Special Function Registers
(from Bank 15).
When a = 1:
The BSR specifies the bank
used by the instruction.
3FFh
400h
GPR
FFh
00h
4FFh
500h
GPR
Bank 5
FFh
00h
5FFh
600h
GPR
Bank 6
FFh
00h
6FFh
700h
GPR
Bank 7
7FFh
800h
Access Bank
00h
Access RAM Low
5Fh
Access RAM High 60h
(SFRs)
FFh
Bank 8
Unused
Read as ‘0’
Bank 14
= 1111
FFh
00h
Unused
FFh
SFR
Bank 15
DS39770B-page 66
The first 96 bytes are general
purpose RAM (from Bank 0).
GPR
FFh
00h
to
= 1110
000h
05Fh
060h
0FFh
100h
GPR
FFh
00h
FFh
00h
= 1000
The BSR is ignored and the
Access Bank is used.
EFFh
F00h
F5Fh
F60h
FFFh
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 5-8:
USE OF THE BANK SELECT REGISTER (DIRECT ADDRESSING)
BSR(1)
7
0
0
0
0
0
0
0
1
000h
Data Memory
Bank 0
0
100h
Bank Select(2)
Bank 1
00h
7
FFh
00h
1
From Opcode(2)
1
11
1
11
1
0
11
11
FFh
00h
200h
Bank 2
FFh
00h
300h
Bank 3
through
Bank 13
FFh
00h
E00h
Bank 14
FFh
00h
F00h
Bank 15
FFFh
Note 1:
2:
5.3.2
FFh
The Access RAM bit of the instruction can be used to force an override of the selected bank (BSR<3:0>)
to the registers of the Access Bank.
The MOVFF instruction embeds the entire 12-bit address in the instruction.
ACCESS BANK
While the use of the BSR with an embedded 8-bit
address allows users to address the entire range of data
memory, it also means that the user must always ensure
that the correct bank is selected. Otherwise, data may
be read from, or written to, the wrong location. This can
be disastrous if a GPR is the intended target of an operation, but an SFR is written to instead. Verifying and/or
changing the BSR for each read or write to data memory
can become very inefficient.
To streamline access for the most commonly used data
memory locations, the data memory is configured with
an Access Bank, which allows users to access a
mapped block of memory without specifying a BSR.
The Access Bank consists of the first 96 bytes of
memory (00h-5Fh) in Bank 0 and the last 160 bytes of
memory (60h-FFh) in Bank 15. The lower half is known
as the “Access RAM” and is composed of GPRs. The
upper half is where the device’s SFRs are mapped.
These two areas are mapped contiguously in the
Access Bank and can be addressed in a linear fashion
by an 8-bit address (Figure 5-6).
The Access Bank is used by core PIC18 instructions
that include the Access RAM bit (the ‘a’ parameter in
the instruction). When ‘a’ is equal to ‘1’, the instruction
uses the BSR and the 8-bit address included in the
opcode for the data memory address. When ‘a’ is ‘0’,
© 2007 Microchip Technology Inc.
however, the instruction is forced to use the Access
Bank address map; the current value of the BSR is
ignored entirely.
Using this “forced” addressing allows the instruction to
operate on a data address in a single cycle without
updating the BSR first. For 8-bit addresses of 60h and
above, this means that users can evaluate and operate
on SFRs more efficiently. The Access RAM below 60h
is a good place for data values that the user might need
to access rapidly, such as immediate computational
results or common program variables. Access RAM
also allows for faster and more code efficient context
saving and switching of variables.
The mapping of the Access Bank is slightly different
when the extended instruction set is enabled (XINST
Configuration bit = 1). This is discussed in more detail
in Section 5.6.3 “Mapping the Access Bank in
Indexed Literal Offset Mode”.
5.3.3
GENERAL PURPOSE
REGISTER FILE
PIC18 devices may have banked memory in the GPR
area. This is data RAM which is available for use by all
instructions. GPRs start at the bottom of Bank 0
(address 000h) and grow upwards towards the bottom of
the SFR area. GPRs are not initialized by a Power-on
Reset and are unchanged on all other Resets.
Preliminary
DS39770B-page 67
PIC18F85J90 FAMILY
5.3.4
SPECIAL FUNCTION REGISTERS
The Special Function Registers (SFRs) are registers
used by the CPU and peripheral modules for controlling
the desired operation of the device. These registers are
implemented as static RAM. SFRs start at the top of
data memory (FFFh) and extend downward to occupy
more than the top half of Bank 15 (F60h to FFFh). A list
of these registers is given in Table 5-2 and Table 5-3.
TABLE 5-2:
Address
The SFRs can be classified into two sets: those
associated with the “core” device functionality (ALU,
Resets and interrupts) and those related to the
peripheral functions. The Reset and Interrupt registers
are described in their respective chapters, while the
ALU’s STATUS register is described later in this section.
Registers related to the operation of the peripheral
features are described in the chapter for that peripheral.
The SFRs are typically distributed among the
peripherals whose functions they control. Unused SFR
locations are unimplemented and read as ‘0’s.
SPECIAL FUNCTION REGISTER MAP FOR PIC18F85J90 FAMILY DEVICES
Name
Address
Name
Name
(3)
Address
Name
Address
Name
FFFh
TOSU
FDFh
F9Fh
IPR1
F7Fh
SPBRGH1
FFEh
TOSH
FDEh POSTINC2(1)
FBEh
LCDDATA3
F9Eh
PIR1
F7Eh
BAUDCON1
FFDh
TOSL
FDDh POSTDEC2(1)
FBDh
LCDDATA2
F9Dh
PIE1
F7Dh LCDDATA23(3)
F9Ch
(2)
F7Ch LCDDATA22(3)
FFCh
STKPTR
INDF2
Address
(1)
(1)
FBFh LCDDATA4
FDCh
PREINC2
FBCh
LCDDATA1
—
FFBh
PCLATU
FDBh
PLUSW2(1)
FBBh
LCDDATA0
F9Bh
OSCTUNE
F7Bh
LCDDATA21
FFAh
PCLATH
FDAh
FSR2H
FBAh
LCDSE5(3)
F9Ah
TRISJ(3)
F7Ah
LCDDATA20
FF9h
PCL
FD9h
FSR2L
FB9h
LCDSE4(3)
F99h
TRISH(3)
F79h
LCDDATA19
FF8h
TBLPTRU
FD8h
STATUS
FB8h
LCDSE3
F98h
TRISG
F78h
LCDDATA18
FF7h
TBLPTRH
FD7h
TMR0H
FB7h
LCDSE2
F97h
TRISF
F77h LCDDATA17(3)
FF6h
TBLPTRL
FD6h
TMR0L
FB6h
LCDSE1
F96h
TRISE
F76h LCDDATA16(3)
FF5h
TABLAT
FD5h
T0CON
FB5h
CVRCON
F95h
TRISD
F75h
LCDDATA15
—
(2)
FF4h
PRODH
FD4h
FB4h
CMCON
F94h
TRISC
F74h
LCDDATA14
FF3h
PRODL
FD3h
OSCCON
FB3h
TMR3H
F93h
TRISB
F73h
LCDDATA13
FF2h
INTCON
FD2h
LCDREG
FB2h
TMR3L
F92h
TRISA
F72h
LCDDATA12
FF1h
INTCON2
FD1h
WDTCON
FB1h
T3CON
F91h
LATJ(3)
F71h LCDDATA11(3)
FF0h
INTCON3
FD0h
RCON
FB0h
—(2)
F90h
LATH(3)
F70h LCDDATA10(3)
FEFh
INDF0(1)
FCFh
TMR1H
FAFh
SPBRG1
F8Fh
LATG
F6Fh
FEEh POSTINC0(1)
FCEh
TMR1L
FAEh
RCREG1
F8Eh
LATF
F6Eh
LCDDATA9
LCDDATA8
FEDh POSTDEC0(1)
FCDh
T1CON
FADh
TXREG1
F8Dh
LATE
F6Dh
LCDDATA7
FECh
PREINC0(1)
FCCh
TMR2
FACh
TXSTA1
F8Ch
LATD
F6Ch
LCDDATA6
FEBh
PLUSW0(1)
FCBh
PR2
FABh
RCSTA1
F8Bh
LATC
F6Bh
LCDDATA5(3)
FEAh
FSR0H
FCAh
T2CON
FAAh
LCDPS
F8Ah
LATB
F6Ah
CCPR1H
FE9h
FSR0L
FC9h
SSPBUF
FA9h
LCDSE0
F89h
LATA
F69h
CCPR1L
(3)
FE8h
WREG
FC8h
SSPADD
FA8h
LCDCON
F88h
PORTJ
F68h
CCP1CON
FE7h
INDF1(1)
FC7h
SSPSTAT
FA7h
EECON2
F87h
PORTH(3)
F67h
CCPR2H
FE6h POSTINC1(1)
FC6h
SSPCON1
FA6h
EECON1
F86h
PORTG
F66h
CCPR2L
FE5h POSTDEC1(1)
FC5h
SSPCON2
FA5h
IPR3
F85h
PORTF
F65h
CCP2CON
FE4h
PREINC1(1)
FC4h
ADRESH
FA4h
PIR3
F84h
PORTE
F64h
SPBRG2
FE3h
PLUSW1(1)
FC3h
ADRESL
FA3h
PIE3
F83h
PORTD
F63h
RCREG2
FE2h
FSR1H
FC2h
ADCON0
FA2h
IPR2
F82h
PORTC
F62h
TXREG2
FE1h
FSR1L
FC1h
ADCON1
FA1h
PIR2
F81h
PORTB
F61h
TXSTA2
FE0h
BSR
FC0h
ADCON2
FA0h
PIE2
F80h
PORTA
F60h
RCSTA2
Note 1:
2:
3:
This is not a physical register.
Unimplemented registers are read as ‘0’.
This register is not available on 64-pin devices.
DS39770B-page 68
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 5-3:
Filename
TOSU
PIC18F85J90 FAMILY REGISTER FILE SUMMARY
Bit 7
Bit 6
Bit 5
—
—
—
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Details
on page
---0 0000
51, 59
TOSH
Top-of-Stack High Byte (TOS<15:8>)
0000 0000
51, 59
TOSL
Top-of-Stack Low Byte (TOS<7:0>)
0000 0000
51, 59
Return Stack Pointer
uu-0 0000
51, 60
Holding Register for PC<20:16>
STKPTR
PCLATU
STKFUL
STKUNF
—
—
—
bit 21(1)
Top-of-Stack Upper Byte (TOS<20:16>)
Value on
POR, BOR
---0 0000
51, 59
PCLATH
Holding Register for PC<15:8>
0000 0000
51, 59
PCL
PC Low Byte (PC<7:0>)
0000 0000
51, 59
--00 0000
51, 84
TBLPTRU
—
—
bit 21
Program Memory Table Pointer Upper Byte (TBLPTR<20:16>)
TBLPTRH
Program Memory Table Pointer High Byte (TBLPTR<15:8>)
0000 0000
51, 84
TBLPTRL
Program Memory Table Pointer Low Byte (TBLPTR<7:0>)
0000 0000
51, 84
TABLAT
Program Memory Table Latch
0000 0000
51, 84
PRODH
Product Register High Byte
xxxx xxxx
51, 91
PRODL
Product Register Low Byte
xxxx xxxx
51, 91
RBIF
0000 000x
51, 95
INTCON
GIE/GIEH
PEIE/GIEL
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
INTCON2
RBPU
INTEDG0
INTEDG1
INTEDG2
INTEDG3
TMR0IP
INT3IP
RBIP
1111 1111
51, 96
INTCON3
INT2IP
INT1IP
INT3IE
INT2IE
INT1IE
INT3IF
INT2IF
INT1IF
1100 0000
51, 97
INDF0
Uses contents of FSR0 to address data memory – value of FSR0 not changed (not a physical register)
N/A
51, 75
POSTINC0
Uses contents of FSR0 to address data memory – value of FSR0 post-incremented (not a physical register)
N/A
51, 76
POSTDEC0
Uses contents of FSR0 to address data memory – value of FSR0 post-decremented (not a physical register)
N/A
51, 76
PREINC0
Uses contents of FSR0 to address data memory – value of FSR0 pre-incremented (not a physical register)
N/A
51, 76
PLUSW0
Uses contents of FSR0 to address data memory – value of FSR0 pre-incremented (not a physical register) –
value of FSR0 offset by W
N/A
51, 76
FSR0H
---- xxxx
51, 75
FSR0L
Indirect Data Memory Address Pointer 0 Low Byte
—
xxxx xxxx
51, 75
WREG
Working Register
xxxx xxxx
51
INDF1
Uses contents of FSR1 to address data memory – value of FSR1 not changed (not a physical register)
N/A
51, 75
POSTINC1
Uses contents of FSR1 to address data memory – value of FSR1 post-incremented (not a physical register)
N/A
51, 76
POSTDEC1
Uses contents of FSR1 to address data memory – value of FSR1 post-decremented (not a physical register)
N/A
51, 76
PREINC1
Uses contents of FSR1 to address data memory – value of FSR1 pre-incremented (not a physical register)
N/A
51, 76
PLUSW1
Uses contents of FSR1 to address data memory – value of FSR1 pre-incremented (not a physical register) –
value of FSR1 offset by W
N/A
51, 76
---- xxxx
52, 75
xxxx xxxx
52, 75
---- 0000
52, 64
FSR1H
—
FSR1L
—
—
—
—
—
—
Indirect Data Memory Address Pointer 0 High
Indirect Data Memory Address Pointer 1 High Byte
Indirect Data Memory Address Pointer 1 Low Byte
BSR
—
—
—
—
Bank Select Register
INDF2
Uses contents of FSR2 to address data memory – value of FSR2 not changed (not a physical register)
N/A
52, 75
POSTINC2
Uses contents of FSR2 to address data memory – value of FSR2 post-incremented (not a physical register)
N/A
52, 76
POSTDEC2
Uses contents of FSR2 to address data memory – value of FSR2 post-decremented (not a physical register)
N/A
52, 76
PREINC2
Uses contents of FSR2 to address data memory – value of FSR2 pre-incremented (not a physical register)
N/A
52, 76
PLUSW2
Uses contents of FSR2 to address data memory – value of FSR2 pre-incremented (not a physical register) –
value of FSR2 offset by W
N/A
52, 76
---- xxxx
52, 75
xxxx xxxx
52, 75
---x xxxx
52, 73
FSR2H
FSR2L
STATUS
Legend:
Note 1:
2:
3:
4:
5:
—
—
—
—
Indirect Data Memory Address Pointer 2 High Byte
Indirect Data Memory Address Pointer 2 Low Byte
—
—
—
N
OV
Z
DC
C
x = unknown, u = unchanged, - = unimplemented, q = value depends on condition, r = reserved, do not modify
Bit 21 of the PC is only available in Test mode and Serial Programming modes.
These registers and/or bits are available only on 80-pin devices; otherwise they are unimplemented and read as ‘0’. Reset states shown are
for 80-pin devices.
Alternate names and definitions for these bits when the MSSP module is operating in I2C™ Slave mode. See Section 16.4.3.2 “Address
Masking” for details.
The PLLEN bit is only available in specific oscillator configurations; otherwise it is disabled and reads as ‘0’. See Section 2.4.3 “PLL
Frequency Multiplier” for details.
RA6/RA7 and their associated latch and direction bits are configured as port pins only when the internal oscillator is selected as the default
clock source (FOSC2 Configuration bit = 0); otherwise, they are disabled and these bits read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 69
PIC18F85J90 FAMILY
TABLE 5-3:
Filename
PIC18F85J90 FAMILY REGISTER FILE SUMMARY (CONTINUED)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
Details
on page
TMR0H
Timer0 Register High Byte
0000 0000
52, 133
TMR0L
Timer0 Register Low Byte
xxxx xxxx
52, 133
52, 131
TMR0ON
T08BIT
T0CS
T0SE
PSA
T0PS2
T0PS1
T0PS0
1111 1111
OSCCON
T0CON
IDLEN
IRCF2
IRCF1
IRCF0
OSTS
IOFS
SCS1
SCS0
0100 q000
30, 52
LCDREG
—
CPEN
BIAS2
BIAS1
BIAS0
MODE13
CKSEL1
CKSEL0
-011 1100
52, 163
WDTCON
REGSLP
—
—
—
—
—
—
SWDTEN
0--- ---0
52, 289
IPEN
—
—
RI
TO
PD
POR
BOR
0--1 11q0
46, 52
xxxx xxxx
52, 139
xxxx xxxx
52, 139
RCON
TMR1H
Timer1 Register High Byte
TMR1L
Timer1 Register Low Byte
T1CON
RD16
T1RUN
TMR2
Timer2 Register
PR2
Timer2 Period Register
T2CON
—
T1CKPS1
T1CKPS0
T1OSCEN
T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0
T1SYNC
TMR2ON
TMR1CS
T2CKPS1
TMR1ON
T2CKPS0
SSPBUF
MSSP Receive Buffer/Transmit Register
SSPADD
MSSP Address Register in I2C™ Slave mode. MSSP1 Baud Rate Reload Register in I2C Master mode.
0000 0000
52, 135
0000 0000
52, 142
1111 1111
52, 142
-000 0000
52, 141
xxxx xxxx
52, 193,
228
0000 0000
52, 228
SSPSTAT
SMP
CKE
D/A
P
S
R/W
UA
BF
0000 0000
52, 186,
195
SSPCON1
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
0000 0000
52, 187,
196
SSPCON2
GCEN
ACKSTAT
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
0000 0000
GCEN
ACKSTAT
52, 197,
198
ADMSK5(3) ADMSK4(3) ADMSK3(3) ADMSK2(3) ADMSK1(3)
SEN
ADRESH
A/D Result Register High Byte
xxxx xxxx
53, 271
ADRESL
A/D Result Register Low Byte
xxxx xxxx
53, 271
ADCON0
ADCAL
—
CHS3
CHS2
CHS1
CHS0
GO/DONE
ADON
0-00 0000
53, 263
ADCON1
—
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
--00 0000
53, 264
ADCON2
ADFM
—
ACQT2
ACQT1
ACQT0
ADCS2
ADCS1
ADCS0
0-00 0000
53, 265
S39C0(2)
S38C0(2)
S37C0(2)
S36C0(2)
S35C0(2)
S34C0(2)
S33C0(2)
S32C0
xxxx xxxx
53, 161
LCDDATA4
LCDDATA3
S31C0
S30C0
S29C0
S28C0
S27C0
S26C0
S25C0
S24C0
xxxx xxxx
53, 161
LCDDATA2
S23C0
S22C0
S21C0
S20C0
S19C0
S18C0
S17C0
S16C0
xxxx xxxx
53, 161
LCDDATA1
S15C0
S14C0
S13C0
S12C0
S11C0
S10C0
S09C0
S08C0
xxxx xxxx
53, 161
LCDDATA0
S07C0
S06C0
S05C0
S04C0
S03C0
S02C0
S01C0
S00C0
xxxx xxxx
53, 161
53, 160
LCDSE5(2)
SE47
SE46
SE45
SE44
SE43
SE42
SE41
SE40
0000 0000
LCDSE4
SE39(2)
SE38(2)
S37(2)
SE36(2)
SE35(2)
SE34(2)
SE33(2)
SE32
0000 0000
53, 160
LCDSE3
SE31
SE30
SE29
SE28
SE27
SE26
SE25
SE24
0000 0000
53, 160
LCDSE2
SE23
SE22
SE21
SE20
SE19
SE18
SE17
SE16
0000 0000
53, 160
LCDSE1
SE15
SE14
SE13
SE12
SE11
SE10
SE09
SE08
0000 0000
53, 160
CVRCON
CVREN
CVROE
CVRR
CVRSS
CVR3
CVR2
CVR1
CVR0
0000 0000
53, 279
CMCON
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
0000 0111
53, 273
TMR3H
Timer3 Register High Byte
xxxx xxxx
53, 145
TMR3L
Timer3 Register Low Byte
xxxx xxxx
53, 145
0000 0000
53, 143
T3CON
Legend:
Note 1:
2:
3:
4:
5:
RD16
T3CCP2
T3CKPS1
T3CKPS0
T3CCP1
T3SYNC
TMR3CS
TMR3ON
x = unknown, u = unchanged, - = unimplemented, q = value depends on condition, r = reserved, do not modify
Bit 21 of the PC is only available in Test mode and Serial Programming modes.
These registers and/or bits are available only on 80-pin devices; otherwise they are unimplemented and read as ‘0’. Reset states shown are
for 80-pin devices.
Alternate names and definitions for these bits when the MSSP module is operating in I2C™ Slave mode. See Section 16.4.3.2 “Address
Masking” for details.
The PLLEN bit is only available in specific oscillator configurations; otherwise it is disabled and reads as ‘0’. See Section 2.4.3 “PLL
Frequency Multiplier” for details.
RA6/RA7 and their associated latch and direction bits are configured as port pins only when the internal oscillator is selected as the default
clock source (FOSC2 Configuration bit = 0); otherwise, they are disabled and these bits read as ‘0’.
DS39770B-page 70
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 5-3:
Filename
PIC18F85J90 FAMILY REGISTER FILE SUMMARY (CONTINUED)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
Details
on page
SPBRG1
EUSART Baud Rate Generator
0000 0000
53, 233
RCREG1
EUSART Receive Register
0000 0000
53, 241
TXREG1
EUSART Transmit Register
TXSTA1
CSRC
RCSTA1
LCDPS
0000 0000
53, 239
0000 0010
53, 230
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
0000 000x
53, 231
WFT
BIASMD
LCDA
WA
LP3
LP2
LP1
LP0
0000 0000
53, 159
LCDSE0
SE07
SE06
SE05
SE04
SE03
SE02
SE01
SE00
0000 0000
53, 160
LCDCON
LCDEN
SLPEN
WERR
—
CS1
CS0
LMUX1
LMUX0
000- 0000
53, 158
---- ----
53, 82
EECON2
EEPROM Control Register 2 (not a physical register)
EECON1
—
—
—
FREE
WRERR
WREN
WR
—
---0 x00-
53, 83
IPR3
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
-111 -11-
54, 106
PIR3
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
-000 -00-
54, 100
PIE3
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
-000 -00-
54, 103
IPR2
OSCFIP
CMIP
—
—
BCLIP
LVDIP
TMR3IP
—
11-- 111-
54, 105
PIR2
OSCFIF
CMIF
—
—
BCLIF
LVDIF
TMR3IF
—
00-- 000-
54, 99
PIE2
OSCFIE
CMIE
—
—
BCLIE
LVDIE
TMR3IE
—
00-- 000-
54, 102
IPR1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
-111 1-11
54, 104
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
-000 0-00
54, 98
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
-000 0-00
54, 101
INTSRC
PLLEN(4)
TUN5
TUN4
TUN3
TUN2
TUN1
TUN0
0000 0000
31, 54
(2)
TRISJ
TRISJ7
TRISJ6
TRISJ5
TRISJ4
TRISJ3
TRISJ2
TRISJ1
TRISJ0
1111 1111
54, 130
TRISH(2)
TRISH7
TRISH6
TRISH5
TRISH4
TRISH3
TRISH2
TRISH1
TRISH0
1111 1111
54, 128
TRISG
SPIOD
CCP2OD
CCP1OD
TRISG4
TRISG3
TRISG2
TRISG1
TRISG0
0001 1111
54, 126
OSCTUNE
TRISF
TRISF7
TRISF6
TRISF5
TRISF4
TRISF3
TRISF2
TRISF1
—
1111 111-
54, 124
TRISE
TRISE7
TRISE6
TRISE5
TRISE4
TRISE3
—
TRISE1
TRISE0
1111 1-11
54, 121
TRISD
TRISD7
TRISD6
TRISD5
TRISD4
TRISD3
TRISD2
TRISD1
TRISD0
1111 1111
54, 119
TRISC
TRISC7
TRISC6
TRISC5
TRISC4
TRISC3
TRISC2
TRISC1
TRISC0
1111 1111
54, 117
TRISB
TRISB7
TRISB6
TRISB5
TRISB4
TRISB3
TRISB2
TRISB1
TRISB0
1111 1111
54, 114
TRISA
TRISA7(5)
TRISA6(5)
TRISA5
TRISA4
TRISA3
TRISA2
TRISA1
TRISA0
1111 1111
54, 111
LATJ(2)
LATJ7
LATJ6
LATJ5
LATJ4
LATJ3
LATJ2
LATJ1
LATJ0
xxxx xxxx
54, 130
LATH(2)
LATH7
LATH6
LATH5
LATH4
LATH3
LATH2
LATH1
LATH0
xxxx xxxx
54, 128
LATG
U2OD
U1OD
—
LATG4
LATG3
LATG2
LATG1
LATG0
00-x xxxx
54, 126
LATF
LATF7
LATF6
LATF5
LATF4
LATF3
LATF2
LATF1
—
xxxx xxx-
54, 124
LATE
LATE7
LATE6
LATE5
LATE4
LATE3
—
LATE1
LATE0
xxxx x-xx
54, 121
LATD
LATD7
LATD6
LATD5
LATD4
LATD3
LATD2
LATD1
LATD0
xxxx xxxx
54, 119
LATC
LATC7
LATC6
LATC5
LATC4
LATC3
LATC2
LATC1
LATC0
xxxx xxxx
54, 117
LATB
LATB7
LATB6
LATB5
LATB4
LATB3
LATB2
LATB1
LATB0
xxxx xxxx
54, 114
LATA
LATA7(5)
LATA6(5)
LATA5
LATA4
LATA3
LATA2
LATA1
LATA0
xxxx xxxx
54, 111
Legend:
Note 1:
2:
3:
4:
5:
x = unknown, u = unchanged, - = unimplemented, q = value depends on condition, r = reserved, do not modify
Bit 21 of the PC is only available in Test mode and Serial Programming modes.
These registers and/or bits are available only on 80-pin devices; otherwise they are unimplemented and read as ‘0’. Reset states shown are
for 80-pin devices.
Alternate names and definitions for these bits when the MSSP module is operating in I2C™ Slave mode. See Section 16.4.3.2 “Address
Masking” for details.
The PLLEN bit is only available in specific oscillator configurations; otherwise it is disabled and reads as ‘0’. See Section 2.4.3 “PLL
Frequency Multiplier” for details.
RA6/RA7 and their associated latch and direction bits are configured as port pins only when the internal oscillator is selected as the default
clock source (FOSC2 Configuration bit = 0); otherwise, they are disabled and these bits read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 71
PIC18F85J90 FAMILY
TABLE 5-3:
Filename
PIC18F85J90 FAMILY REGISTER FILE SUMMARY (CONTINUED)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
Details
on page
54, 130
PORTJ(2)
RJ7
RJ6
RJ5
RJ4
RJ3
RJ2
RJ1
RJ0
xxxx xxxx
PORTH(2)
RH7
RH6
RH5
RH4
RH3
RH2
RH1
RH0
xxxx xxxx
54, 128
RDPU
REPU
RJPU(2)
RG4
RG3
RG2
RG1
RG0
000x xxxx
54, 126
PORTG
PORTF
RF7
RF6
RF5
RF4
RF3
RF2
RF1
—
xxxx xxx-
54, 124
PORTE
RE7
RE6
RE5
RE4
RE3
—
RE1
RE0
xxxx x-xx
55, 121
PORTD
RD7
RD6
RD5
RD4
RD3
RD2
RD1
RD0
xxxx xxxx
55, 119
PORTC
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
xxxx xxxx
55, 117
PORTB
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx xxxx
55, 114
PORTA
RA7(5)
RA6(5)
RA5
RA4
RA3
RA2
RA1
RA0
xx0x 0000
55, 111
0000 0000
55, 233
SPBRGH1
EUSART Baud Rate Generator High Byte
BAUDCON1
ABDOVF
RCMT
—
SCKP
BRG16
—
WUE
ABDEN
01-0 0-00
55, 232
S47C3
S46C3
S45C3
S44C3
S43C3
S42C3
S41C3
S40C3
xxxx xxxx
55, 161
LCDDATA22
S39C3(2)
S38C3(2)
S37C3(2)
S36C3(2)
S35C3(2)
S34C3(2)
S33C3(2)
S32C3
xxxx xxxx
55, 161
LCDDATA21
S31C3
S30C3
S29C3
S28C3
S27C3
S26C3
S25C3
S24C3
xxxx xxxx
55, 161
LCDDATA23(2)
LCDDATA20
S23C3
S22C3
S21C3
S20C3
S19C3
S18C3
S17C3
S16C3
xxxx xxxx
55, 161
LCDDATA19
S15C3
S14C3
S13C3
S12C3
S11C3
S10C3
S09C3
S08C3
xxxx xxxx
55, 161
LCDDATA18
S07C3
S06C3
S05C3
S04C3
S03C3
S02C3
S01C3
S00C3
xxxx xxxx
55, 161
LCDDATA17(2)
S47C2
S46C2
S45C2
S44C2
S43C2
S42C2
S41C2
S40C2
xxxx xxxx
55, 161
LCDDATA16
S39C2(2)
S38C2(2)
S37C2(2)
S36C2(2)
S35C2(2)
S34C2(2)
S33C2(2)
S32C2
xxxx xxxx
55, 161
LCDDATA15
S31C2
S30C2
S29C2
S28C2
S27C2
S26C2
S25C2
S24C2
xxxx xxxx
55, 161
LCDDATA14
S23C2
S22C2
S21C2
S20C2
S19C2
S18C2
S17C2
S16C2
xxxx xxxx
55, 161
LCDDATA13
S15C2
S14C2
S13C2
S12C2
S11C2
S10C2
S09C2
S08C2
xxxx xxxx
55, 161
LCDDATA12
S07C2
S06C2
S05C2
S04C2
S03C2
S02C2
S01C2
S00C2
xxxx xxxx
55, 161
LCDDATA11(2)
S47C1
S46C1
S45C1
S44C1
S43C1
S42C1
S41C1
S40C1
xxxx xxxx
55, 161
LCDDATA10
S39C1(2)
S38C1(2)
S37C1(2)
S36C1(2)
S35C1(2)
S34C1(2)
S33C1(2)
S32C1
xxxx xxxx
55, 161
LCDDATA9
S31C1
S30C1
S29C1
S28C1
S27C1
S26C1
S25C1
S24C1
xxxx xxxx
55, 161
LCDDATA8
S23C1
S22C1
S21C1
S20C1
S19C1
S18C1
S17C1
S16C1
xxxx xxxx
55, 161
LCDDATA7
S15C1
S14C1
S13C1
S12C1
S11C1
S10C1
S09C1
S08C1
xxxx xxxx
55, 161
55, 161
LCDDATA6
S07C1
S06C1
S05C1
S04C1
S03C1
S02C1
S01C1
S00C1
xxxx xxxx
LCDDATA5(2)
S47C0
S46C0
S45C0
S44C0
S43C0
S42C0
S41C0
S40C0
xxxx xxxx
55, 161
xxxx xxxx
55, 148
xxxx xxxx
55, 148
CCPR1H
Capture/Compare/PWM Register 1 High Byte
CCPR1L
Capture/Compare/PWM Register 1 Low Byte
CCP1CON
—
—
DC1B1
DC1B0
CCPR2H
Capture/Compare/PWM Register 2 High Byte
CCPR2L
Capture/Compare/PWM Register 2 Low Byte
CCP2CON
SPBRG2
—
—
DC2B1
DC2B0
CCP1M3
CCP2M3
CCP1M2
CCP2M2
CCP1M1
CCP2M1
CCP1M0
CCP2M0
AUSART Baud Rate Generator Register
--00 0000
55, 147
xxxx xxxx
55, 148
xxxx xxxx
56, 148
--00 0000
56, 147
0000 0000
56, 252
RCREG2
AUSART Receive Register
0000 0000
56, 257
TXREG2
AUSART Transmit Register
0000 0000
56, 255
TXSTA2
CSRC
TX9
TXEN
SYNC
—
BRGH
TRMT
TX9D
0000 -010
56, 250
RCSTA2
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
0000 000x
56, 251
Legend:
Note 1:
2:
3:
4:
5:
x = unknown, u = unchanged, - = unimplemented, q = value depends on condition, r = reserved, do not modify
Bit 21 of the PC is only available in Test mode and Serial Programming modes.
These registers and/or bits are available only on 80-pin devices; otherwise they are unimplemented and read as ‘0’. Reset states shown are
for 80-pin devices.
Alternate names and definitions for these bits when the MSSP module is operating in I2C™ Slave mode. See Section 16.4.3.2 “Address
Masking” for details.
The PLLEN bit is only available in specific oscillator configurations; otherwise it is disabled and reads as ‘0’. See Section 2.4.3 “PLL
Frequency Multiplier” for details.
RA6/RA7 and their associated latch and direction bits are configured as port pins only when the internal oscillator is selected as the default
clock source (FOSC2 Configuration bit = 0); otherwise, they are disabled and these bits read as ‘0’.
DS39770B-page 72
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
5.3.5
STATUS REGISTER
The STATUS register, shown in Register 5-2, contains
the arithmetic status of the ALU. The STATUS register
can be the operand for any instruction, as with any
other register. If the STATUS register is the destination
for an instruction that affects the Z, DC, C, OV or N bits,
then the write to these five bits is disabled.
These bits are set or cleared according to the device
logic. Therefore, the result of an instruction with the
STATUS register as destination may be different than
intended. For example, CLRF STATUS will set the Z bit
but leave the other bits unchanged. The STATUS
REGISTER 5-2:
U-0
For other instructions not affecting any Status bits, see
the instruction set summaries in Table 23-2 and
Table 23-3.
Note:
The C and DC bits operate as a borrow and
digit borrow bit respectively, in subtraction.
STATUS REGISTER
U-0
—
register then reads back as ‘000u u1uu’. It is recommended, therefore, that only BCF, BSF, SWAPF,
MOVFF and MOVWF instructions are used to alter the
STATUS register because these instructions do not
affect the Z, C, DC, OV or N bits in the STATUS
register.
U-0
—
—
R/W-x
N
R/W-x
R/W-x
R/W-x
R/W-x
Z
DC(1)
C(2)
OV
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-5
Unimplemented: Read as ‘0’
bit 4
N: Negative bit
This bit is used for signed arithmetic (2’s complement). It indicates whether the result was
negative (ALU MSB = 1).
1 = Result was negative
0 = Result was positive
bit 3
OV: Overflow bit
This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the
7-bit magnitude which causes the sign bit (bit 7) to change state.
1 = Overflow occurred for signed arithmetic (in this arithmetic operation)
0 = No overflow occurred
bit 2
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
bit 1
DC: Digit Carry/Borrow bit(1)
For ADDWF, ADDLW, SUBLW and SUBWF instructions:
1 = A carry-out from the 4th low-order bit of the result occurred
0 = No carry-out from the 4th low-order bit of the result
bit 0
C: Carry/Borrow bit(2)
For ADDWF, ADDLW, SUBLW and SUBWF instructions:
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
Note 1:
2:
For borrow, the polarity is reversed. A subtraction is executed by adding the 2’s complement of the second
operand. For rotate (RRF, RLF) instructions, this bit is loaded with either bit 4 or bit 3 of the source register.
For borrow, the polarity is reversed. A subtraction is executed by adding the 2’s complement of the second
operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low-order bit of the
source register.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 73
PIC18F85J90 FAMILY
5.4
Data Addressing Modes
Note:
The execution of some instructions in the
core PIC18 instruction set are changed
when the PIC18 extended instruction set is
enabled. See Section 5.6 “Data Memory
and the Extended Instruction Set” for
more information.
While the program memory can be addressed in only
one way – through the program counter – information
in the data memory space can be addressed in several
ways. For most instructions, the addressing mode is
fixed. Other instructions may use up to three modes,
depending on which operands are used and whether or
not the extended instruction set is enabled.
The addressing modes are:
•
•
•
•
Inherent
Literal
Direct
Indirect
INHERENT AND LITERAL
ADDRESSING
Many PIC18 control instructions do not need any
argument at all; they either perform an operation that
globally affects the device, or they operate implicitly on
one register. This addressing mode is known as Inherent
Addressing. Examples include SLEEP, RESET and DAW.
Other instructions work in a similar way, but require an
additional explicit argument in the opcode. This is
known as Literal Addressing mode, because they
require some literal value as an argument. Examples
include ADDLW and MOVLW, which respectively, add or
move a literal value to the W register. Other examples
include CALL and GOTO, which include a 20-bit
program memory address.
5.4.2
A few instructions, such as MOVFF, include the entire
12-bit address (either source or destination) in their
opcodes. In these cases, the BSR is ignored entirely.
The destination of the operation’s results is determined
by the destination bit ‘d’. When ‘d’ is ‘1’, the results are
stored back in the source register, overwriting its original contents. When ‘d’ is ‘0’, the results are stored in
the W register. Instructions without the ‘d’ argument
have a destination that is implicit in the instruction; their
destination is either the target register being operated
on or the W register.
5.4.3
An additional addressing mode, Indexed Literal Offset,
is available when the extended instruction set is
enabled (XINST Configuration bit = 1). Its operation is
discussed in greater detail in Section 5.6.1 “Indexed
Addressing with Literal Offset”.
5.4.1
The Access RAM bit ‘a’ determines how the address is
interpreted. When ‘a’ is ‘1’, the contents of the BSR
(Section 5.3.1 “Bank Select Register”) are used with
the address to determine the complete 12-bit address
of the register. When ‘a’ is ‘0’, the address is interpreted
as being a register in the Access Bank. Addressing that
uses the Access RAM is sometimes also known as
Direct Forced Addressing mode.
INDIRECT ADDRESSING
Indirect Addressing allows the user to access a location
in data memory without giving a fixed address in the
instruction. This is done by using File Select Registers
(FSRs) as pointers to the locations to be read or written
to. Since the FSRs are themselves located in RAM as
Special Function Registers, they can also be directly
manipulated under program control. This makes FSRs
very useful in implementing data structures such as
tables and arrays in data memory.
The registers for Indirect Addressing are also
implemented with Indirect File Operands (INDFs) that
permit automatic manipulation of the pointer value with
auto-incrementing, auto-decrementing or offsetting
with another value. This allows for efficient code using
loops, such as the example of clearing an entire RAM
bank in Example 5-5. It also enables users to perform
Indexed Addressing and other Stack Pointer
operations for program memory in data memory.
EXAMPLE 5-5:
DIRECT ADDRESSING
LFSR
CLRF
Direct Addressing specifies all or part of the source
and/or destination address of the operation within the
opcode itself. The options are specified by the
arguments accompanying the instruction.
NEXT
In the core PIC18 instruction set, bit-oriented and
byte-oriented instructions use some version of Direct
Addressing by default. All of these instructions include
some 8-bit literal address as their Least Significant
Byte. This address specifies either a register address in
one of the banks of data RAM (Section 5.3.3 “General
Purpose Register File”), or a location in the Access
Bank (Section 5.3.2 “Access Bank”) as the data
source for the instruction.
BRA
CONTINUE
DS39770B-page 74
BTFSS
Preliminary
HOW TO CLEAR RAM
(BANK 1) USING
INDIRECT ADDRESSING
FSR0, 100h ;
POSTINC0
; Clear INDF
; register then
; inc pointer
FSR0H, 1
; All done with
; Bank1?
NEXT
; NO, clear next
; YES, continue
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
5.4.3.1
FSR Registers and the
INDF Operand
the SFR space but are not physically implemented.
Reading or writing to a particular INDF register actually
accesses its corresponding FSR register pair. A read
from INDF1, for example, reads the data at the address
indicated by FSR1H:FSR1L. Instructions that use the
INDF registers as operands actually use the contents
of their corresponding FSR as a pointer to the instruction’s target. The INDF operand is just a convenient
way of using the pointer.
At the core of Indirect Addressing are three sets of
registers: FSR0, FSR1 and FSR2. Each represents a
pair of 8-bit registers, FSRnH and FSRnL. The four
upper bits of the FSRnH register are not used, so each
FSR pair holds a 12-bit value. This represents a value
that can address the entire range of the data memory
in a linear fashion. The FSR register pairs, then, serve
as pointers to data memory locations.
Because Indirect Addressing uses a full 12-bit address,
data RAM banking is not necessary. Thus, the current
contents of the BSR and the Access RAM bit have no
effect on determining the target address.
Indirect Addressing is accomplished with a set of Indirect File Operands, INDF0 through INDF2. These can
be thought of as “virtual” registers: they are mapped in
FIGURE 5-9:
INDIRECT ADDRESSING
000h
Using an instruction with one of the
Indirect Addressing registers as the
operand....
Bank 0
ADDWF, INDF1, 1
100h
Bank 1
200h
Bank 2
...uses the 12-bit address stored in
the FSR pair associated with that
register....
300h
FSR1H:FSR1L
7
0
x x x x 1 1 1 1
7
0
1 1 0 0 1 1 0 0
Bank 3
through
Bank 13
...to determine the data memory
location to be used in that operation.
E00h
In this case, the FSR1 pair contains
FCCh. This means the contents of
location FCCh will be added to that
of the W register and stored back in
FCCh.
Bank 14
F00h
Bank 15
FFFh
Data Memory
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 75
PIC18F85J90 FAMILY
5.4.3.2
FSR Registers and POSTINC,
POSTDEC, PREINC and PLUSW
In addition to the INDF operand, each FSR register pair
also has four additional indirect operands. Like INDF,
these are “virtual” registers that cannot be indirectly
read or written to. Accessing these registers actually
accesses the associated FSR register pair, but also
performs a specific action on its stored value. They are:
• POSTDEC: accesses the FSR value, then
automatically decrements it by ‘1’ afterwards
• POSTINC: accesses the FSR value, then
automatically increments it by ‘1’ afterwards
• PREINC: increments the FSR value by ‘1’, then
uses it in the operation
• PLUSW: adds the signed value of the W register
(range of -127 to 128) to that of the FSR and uses
the new value in the operation
In this context, accessing an INDF register uses the
value in the FSR registers without changing them.
Similarly, accessing a PLUSW register gives the FSR
value offset by the value in the W register; neither value
is actually changed in the operation. Accessing the
other virtual registers changes the value of the FSR
registers.
Operations on the FSRs with POSTDEC, POSTINC
and PREINC affect the entire register pair; that is, rollovers of the FSRnL register from FFh to 00h carry over
to the FSRnH register. On the other hand, results of
these operations do not change the value of any flags
in the STATUS register (e.g., Z, N, OV, etc.).
The PLUSW register can be used to implement a form
of Indexed Addressing in the data memory space. By
manipulating the value in the W register, users can
reach addresses that are fixed offsets from pointer
addresses. In some applications, this can be used to
implement some powerful program control structure,
such as software stacks, inside of data memory.
DS39770B-page 76
5.4.3.3
Operations by FSRs on FSRs
Indirect Addressing operations that target other FSRs
or virtual registers represent special cases. For example, using an FSR to point to one of the virtual registers
will not result in successful operations. As a specific
case, assume that FSR0H:FSR0L contains FE7h, the
address of INDF1. Attempts to read the value of the
INDF1, using INDF0 as an operand, will return 00h.
Attempts to write to INDF1, using INDF0 as the
operand, will result in a NOP.
On the other hand, using the virtual registers to write to
an FSR pair may not occur as planned. In these cases,
the value will be written to the FSR pair but without any
incrementing or decrementing. Thus, writing to INDF2
or POSTDEC2 will write the same value to the
FSR2H:FSR2L.
Since the FSRs are physical registers mapped in the
SFR space, they can be manipulated through all direct
operations. Users should proceed cautiously when
working on these registers, particularly if their code
uses Indirect Addressing.
Similarly, operations by Indirect Addressing are generally permitted on all other SFRs. Users should exercise
the appropriate caution that they do not inadvertently
change settings that might affect the operation of the
device.
5.5
Program Memory and the
Extended Instruction Set
The operation of program memory is unaffected by the
use of the extended instruction set.
Enabling the extended instruction set adds five
additional two-word commands to the existing PIC18
instruction set: ADDFSR, CALLW, MOVSF, MOVSS and
SUBFSR. These instructions are executed as described
in Section 5.2.4 “Two-Word Instructions”.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
5.6
5.6.2
Data Memory and the Extended
Instruction Set
Enabling the PIC18 extended instruction set (XINST
Configuration bit = 1) significantly changes certain
aspects of data memory and its addressing. Specifically,
the use of the Access Bank for many of the core PIC18
instructions is different; this is due to the introduction of
a new addressing mode for the data memory space.
This mode also alters the behavior of Indirect
Addressing using FSR2 and its associated operands.
What does not change is just as important. The size of
the data memory space is unchanged, as well as its
linear addressing. The SFR map remains the same.
Core PIC18 instructions can still operate in both Direct
and Indirect Addressing mode; inherent and literal
instructions do not change at all. Indirect Addressing
with FSR0 and FSR1 also remains unchanged.
5.6.1
INDEXED ADDRESSING WITH
LITERAL OFFSET
Enabling the PIC18 extended instruction set changes
the behavior of Indirect Addressing using the FSR2
register pair and its associated file operands. Under the
proper conditions, instructions that use the Access
Bank – that is, most bit-oriented and byte-oriented
instructions – can invoke a form of Indexed Addressing
using an offset specified in the instruction. This special
addressing mode is known as Indexed Addressing with
Literal Offset, or Indexed Literal Offset mode.
INSTRUCTIONS AFFECTED BY
INDEXED LITERAL OFFSET MODE
Any of the core PIC18 instructions that can use Direct
Addressing are potentially affected by the Indexed
Literal Offset Addressing mode. This includes all
byte-oriented and bit-oriented instructions, or almost
one-half of the standard PIC18 instruction set. Instructions that only use Inherent or Literal Addressing
modes are unaffected.
Additionally, byte-oriented and bit-oriented instructions
are not affected if they use the Access Bank (Access
RAM bit is ‘1’) or include a file address of 60h or above.
Instructions meeting these criteria will continue to
execute as before. A comparison of the different possible addressing modes when the extended instruction
set is enabled is shown in Figure 5-10.
Those who desire to use byte-oriented or bit-oriented
instructions in the Indexed Literal Offset mode should
note the changes to assembler syntax for this mode.
This is described in more detail in Section 23.2.1
“Extended Instruction Syntax”.
When using the extended instruction set, this
addressing mode requires the following:
• The use of the Access Bank is forced (‘a’ = 0);
and
• The file address argument is less than or equal to
5Fh.
Under these conditions, the file address of the
instruction is not interpreted as the lower byte of an
address (used with the BSR in Direct Addressing) or as
an 8-bit address in the Access Bank. Instead, the value
is interpreted as an offset value to an Address Pointer
specified by FSR2. The offset and the contents of FSR2
are added to obtain the target address of the operation.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 77
PIC18F85J90 FAMILY
FIGURE 5-10:
COMPARING ADDRESSING OPTIONS FOR BIT-ORIENTED AND
BYTE-ORIENTED INSTRUCTIONS (EXTENDED INSTRUCTION SET ENABLED)
EXAMPLE INSTRUCTION: ADDWF, f, d, a (Opcode: 0010 01da ffff ffff)
When a = 0 and f ≥ 60h:
The instruction executes in
Direct Forced mode. ‘f’ is
interpreted as a location in the
Access RAM between 060h
and FFFh. This is the same as
locations F60h to FFFh
(Bank 15) of data memory.
Locations below 060h are not
available in this addressing
mode.
000h
060h
Bank 0
100h
00h
Bank 1
through
Bank 14
60h
Valid range
for ‘f’
FFh
F00h
Access RAM
Bank 15
F40h
SFRs
FFFh
Data Memory
When a = 0 and f ≤ 5Fh:
The instruction executes in
Indexed Literal Offset mode. ‘f’
is interpreted as an offset to the
address value in FSR2. The
two are added together to
obtain the address of the target
register for the instruction. The
address can be anywhere in
the data memory space.
Note that in this mode, the
correct syntax is now:
ADDWF [k], d
where ‘k’ is the same as ‘f’.
000h
Bank 0
060h
100h
001001da ffffffff
Bank 1
through
Bank 14
FSR2H
FSR2L
F00h
Bank 15
F40h
SFRs
FFFh
Data Memory
When a = 1 (all values of f):
The instruction executes in
Direct mode (also known as
Direct Long mode). ‘f’ is
interpreted as a location in
one of the 16 banks of the data
memory space. The bank is
designated by the Bank Select
Register (BSR). The address
can be in any implemented
bank in the data memory
space.
BSR
00000000
000h
Bank 0
060h
100h
Bank 1
through
Bank 14
001001da ffffffff
F00h
Bank 15
F40h
SFRs
FFFh
Data Memory
DS39770B-page 78
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
5.6.3
MAPPING THE ACCESS BANK IN
INDEXED LITERAL OFFSET MODE
The use of Indexed Literal Offset Addressing mode
effectively changes how the lower part of Access RAM
(00h to 5Fh) is mapped. Rather than containing just the
contents of the bottom part of Bank 0, this mode maps
the contents from Bank 0 and a user-defined “window”
that can be located anywhere in the data memory
space. The value of FSR2 establishes the lower boundary of the addresses mapped into the window, while the
upper boundary is defined by FSR2 plus 95 (5Fh).
Addresses in the Access RAM above 5Fh are mapped
as previously described (see Section 5.3.2 “Access
Bank”). An example of Access Bank remapping in this
addressing mode is shown in Figure 5-11.
FIGURE 5-11:
Remapping of the Access Bank applies only to operations using the Indexed Literal Offset mode. Operations
that use the BSR (Access RAM bit is ‘1’) will continue
to use Direct Addressing as before. Any Indirect or
Indexed Addressing operation that explicitly uses any
of the indirect file operands (including FSR2) will continue to operate as standard Indirect Addressing. Any
instruction that uses the Access Bank, but includes a
register address of greater than 05Fh, will use Direct
Addressing and the normal Access Bank map.
5.6.4
BSR IN INDEXED LITERAL
OFFSET MODE
Although the Access Bank is remapped when the
extended instruction set is enabled, the operation of the
BSR remains unchanged. Direct Addressing, using the
BSR to select the data memory bank, operates in the
same manner as previously described.
REMAPPING THE ACCESS BANK WITH INDEXED LITERAL
OFFSET ADDRESSING
Example Situation:
ADDWF f, d, a
FSR2H:FSR2L = 120h
Locations in the region
from the FSR2 Pointer
(120h) to the pointer plus
05Fh (17Fh) are mapped
to the bottom of the
Access RAM (000h-05Fh).
000h
05Fh
Bank 0
100h
120h
17Fh
Window
00h
Bank 1
Bank 1 “Window”
200h
5Fh
60h
Special Function Registers at F60h through FFFh
are mapped to 60h
through FFh, as usual.
Bank 0 addresses below
5Fh are not available in
this mode. They can still
be addressed by using the
BSR.
Not Accessible
Bank 2
through
Bank 14
SFRs
FFh
Access Bank
F00h
Bank 15
F60h
FFFh
SFRs
Data Memory
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 79
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 80
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
6.0
FLASH PROGRAM MEMORY
6.1
Table Reads and Table Writes
The Flash program memory is readable, writable and
erasable during normal operation over the entire VDD
range.
In order to read and write program memory, there are
two operations that allow the processor to move bytes
between the program memory space and the data RAM:
A read from program memory is executed on one byte
at a time. A write to program memory is executed on
blocks of 64 bytes at a time. Program memory is
erased in blocks of 1024 bytes at a time. A Bulk Erase
operation may not be issued from user code.
• Table Read (TBLRD)
• Table Write (TBLWT)
Writing or erasing program memory will cease
instruction fetches until the operation is complete. The
program memory cannot be accessed during the write
or erase, therefore, code cannot execute. An internal
programming timer terminates program memory writes
and erases.
A value written to program memory does not need to be
a valid instruction. Executing a program memory
location that forms an invalid instruction results in a
NOP.
The program memory space is 16 bits wide, while the
data RAM space is 8 bits wide. Table reads and table
writes move data between these two memory spaces
through an 8-bit register (TABLAT).
Table read operations retrieve data from program
memory and place it into the data RAM space.
Figure 6-1 shows the operation of a table read with
program memory and data RAM.
Table write operations store data from the data memory
space into holding registers in program memory. The
procedure to write the contents of the holding registers
into program memory is detailed in Section 6.5 “Writing
to Flash Program Memory”. Figure 6-2 shows the
operation of a table write with program memory and data
RAM.
Table operations work with byte entities. A table block
containing data, rather than program instructions, is not
required to be word-aligned. Therefore, a table block can
start and end at any byte address. If a table write is being
used to write executable code into program memory,
program instructions will need to be word-aligned.
FIGURE 6-1:
TABLE READ OPERATION
Instruction: TBLRD*
Program Memory
Table Pointer(1)
TBLPTRU
TBLPTRH
Table Latch (8-bit)
TBLPTRL
TABLAT
Program Memory
(TBLPTR)
Note 1:
Table Pointer register points to a byte in program memory.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 81
PIC18F85J90 FAMILY
FIGURE 6-2:
TABLE WRITE OPERATION
Instruction: TBLWT*
Program Memory
Holding Registers
Table Pointer(1)
TBLPTRU
TBLPTRH
Table Latch (8-bit)
TBLPTRL
TABLAT
Program Memory
(TBLPTR)
Note 1:
6.2
Table Pointer actually points to one of 64 holding registers, the address of which is determined by
TBLPTRL<5:0>. The process for physically writing data to the program memory array is discussed in
Section 6.5 “Writing to Flash Program Memory”.
Control Registers
Several control registers are used in conjunction with
the TBLRD and TBLWT instructions. These include the:
•
•
•
•
EECON1 register
EECON2 register
TABLAT register
TBLPTR registers
6.2.1
The WREN bit, when set, will allow a write operation.
On power-up, the WREN bit is clear. The WRERR bit is
set in hardware when the WR bit is set and cleared
when the internal programming timer expires and the
write operation is complete.
Note:
EECON1 AND EECON2 REGISTERS
The EECON1 register (Register 6-1) is the control
register for memory accesses. The EECON2 register is
not a physical register; it is used exclusively in the
memory write and erase sequences. Reading
EECON2 will read all ‘0’s.
During normal operation, the WRERR is
read as ‘1’. This can indicate that a write
operation was prematurely terminated by
a Reset, or a write operation was
attempted improperly.
The WR control bit initiates write operations. The bit
cannot be cleared, only set, in software. It is cleared in
hardware at the completion of the write operation.
The FREE bit, when set, will allow a program memory
erase operation. When FREE is set, the erase
operation is initiated on the next WR command. When
FREE is clear, only writes are enabled.
DS39770B-page 82
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 6-1:
EECON1: EEPROM CONTROL REGISTER 1
U-0
U-0
U-0
R/W-0
R/W-x
R/W-0
R/S-0
U-0
—
—
—
FREE
WRERR
WREN
WR
—
bit 7
bit 0
Legend:
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
S = Set only bit (cannot be cleared in software)
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-5
Unimplemented: Read as ‘0’
bit 4
FREE: Flash Row Erase Enable bit
1 = Erase the program memory row addressed by TBLPTR on the next WR command (cleared by
completion of erase operation)
0 = Perform write only
bit 3
WRERR: Flash Program Error Flag bit
1 = A write operation is prematurely terminated (any Reset during self-timed programming in normal
operation, or an improper write attempt)
0 = The write operation completed
bit 2
WREN: Flash Program Write Enable bit
1 = Allows write cycles to Flash program memory
0 = Inhibits write cycles to Flash program memory
bit 1
WR: Write Control bit
1 = Initiates a program memory erase cycle or write cycle
(The operation is self-timed and the bit is cleared by hardware once write is complete.
The WR bit can only be set (not cleared) in software.)
0 = Write cycle is complete
bit 0
Unimplemented: Read as ‘0’
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 83
PIC18F85J90 FAMILY
6.2.2
TABLE LATCH REGISTER (TABLAT)
6.2.4
The Table Latch (TABLAT) is an 8-bit register mapped
into the SFR space. The Table Latch register is used to
hold 8-bit data during data transfers between program
memory and data RAM.
6.2.3
TBLPTR is used in reads, writes and erases of the
Flash program memory.
When a TBLRD is executed, all 22 bits of the TBLPTR
determine which byte is read from program memory
into TABLAT.
TABLE POINTER REGISTER
(TBLPTR)
When a TBLWT is executed, the seven LSbs of the
Table Pointer register (TBLPTR<6:0>) determine which
of the 64 program memory holding registers is written
to. When the timed write to program memory begins
(via the WR bit), the 12 MSbs of the TBLPTR
(TBLPTR<21:10>) determine which program memory
block of 1024 bytes is written to. For more detail, see
Section 6.5 “Writing to Flash Program Memory”.
The Table Pointer (TBLPTR) register addresses a byte
within the program memory. The TBLPTR is comprised
of three SFR registers: Table Pointer Upper Byte, Table
Pointer High Byte and Table Pointer Low Byte
(TBLPTRU:TBLPTRH:TBLPTRL). These three registers join to form a 22-bit wide pointer. The low-order
21 bits allow the device to address up to 2 Mbytes of
program memory space. The 22nd bit allows access to
the device ID, the user ID and the Configuration bits.
When an erase of program memory is executed, the
12 MSbs of the Table Pointer register point to the
1024-byte block that will be erased. The Least
Significant bits are ignored.
The Table Pointer register, TBLPTR, is used by the
TBLRD and TBLWT instructions. These instructions can
update the TBLPTR in one of four ways based on the
table operation. These operations are shown in
Table 6-1. These operations on the TBLPTR only affect
the low-order 21 bits.
TABLE 6-1:
TABLE POINTER BOUNDARIES
Figure 6-3 describes the relevant boundaries of the
TBLPTR based on Flash program memory operations.
TABLE POINTER OPERATIONS WITH TBLRD AND TBLWT INSTRUCTIONS
Example
Operation on Table Pointer
TBLRD*
TBLWT*
TBLPTR is not modified
TBLRD*+
TBLWT*+
TBLPTR is incremented after the read/write
TBLRD*TBLWT*-
TBLPTR is decremented after the read/write
TBLRD+*
TBLWT+*
TBLPTR is incremented before the read/write
FIGURE 6-3:
21
TABLE POINTER BOUNDARIES BASED ON OPERATION
TBLPTRU
16
15
TBLPTRH
8
7
TBLPTRL
0
ERASE: TBLPTR<21:10>
TABLE WRITE: TBLPTR<21:6>
TABLE READ: TBLPTR<21:0>
DS39770B-page 84
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
6.3
Reading the Flash Program Memory
The internal program memory is typically organized by
words. The Least Significant bit of the address selects
between the high and low bytes of the word. Figure 6-4
shows the interface between the internal program
memory and the TABLAT.
The TBLRD instruction is used to retrieve data from
program memory and places it into data RAM. Table
reads from program memory are performed one byte at
a time.
TBLPTR points to a byte address in program space.
Executing TBLRD places the byte pointed to into
TABLAT. In addition, TBLPTR can be modified
automatically for the next table read operation.
FIGURE 6-4:
READS FROM FLASH PROGRAM MEMORY
Program Memory
(Even Byte Address)
(Odd Byte Address)
TBLPTR = xxxxx1
Instruction Register
(IR)
EXAMPLE 6-1:
TBLRD
FETCH
TBLPTR = xxxxx0
TABLAT
Read Register
READING A FLASH PROGRAM MEMORY WORD
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
CODE_ADDR_UPPER
TBLPTRU
CODE_ADDR_HIGH
TBLPTRH
CODE_ADDR_LOW
TBLPTRL
; Load TBLPTR with the base
; address of the word
READ_WORD
TBLRD*+
MOVF
MOVWF
TBLRD*+
MOVF
MOVWF
TABLAT, W
WORD_EVEN
TABLAT, W
WORD_ODD
© 2007 Microchip Technology Inc.
; read into TABLAT and increment
; get data
; read into TABLAT and increment
; get data
Preliminary
DS39770B-page 85
PIC18F85J90 FAMILY
6.4
Erasing Flash Program Memory
The minimum erase block is 512 words or 1024 bytes.
Only through the use of an external programmer, or
through ICSP control, can larger blocks of program
memory be Bulk Erased. Word erase in the Flash array
is not supported.
When initiating an erase sequence from the microcontroller itself, a block of 1024 bytes of program
memory is erased. The Most Significant 12 bits of the
TBLPTR<21:10> point to the block being erased;
TBLPTR<9:0> are ignored.
The EECON1 register commands the erase operation.
The WREN bit must be set to enable write operations.
The FREE bit is set to select an erase operation. For
protection, the write initiate sequence for EECON2
must be used.
A long write is necessary for erasing the internal Flash.
Instruction execution is halted while in a long write
cycle. The long write will be terminated by the internal
programming timer.
EXAMPLE 6-2:
6.4.1
FLASH PROGRAM MEMORY
ERASE SEQUENCE
The sequence of events for erasing a block of internal
program memory location is:
1.
2.
3.
4.
5.
6.
7.
8.
Load Table Pointer register with address of row
being erased.
Set the WREN and FREE bits (EECON1<2,4>)
to enable the erase operation.
Disable interrupts.
Write 55h to EECON2.
Write 0AAh to EECON2.
Set the WR bit. This will begin the Row Erase
cycle.
The CPU will stall for duration of the erase for
TIW (see parameter D133A).
Re-enable interrupts.
ERASING A FLASH PROGRAM MEMORY ROW
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
CODE_ADDR_UPPER
TBLPTRU
CODE_ADDR_HIGH
TBLPTRH
CODE_ADDR_LOW
TBLPTRL
; load TBLPTR with the base
; address of the memory block
BSF
BSF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
BSF
EECON1,
EECON1,
INTCON,
55h
EECON2
0AAh
EECON2
EECON1,
INTCON,
; enable write to memory
; enable Row Erase operation
; disable interrupts
ERASE_ROW
Required
Sequence
DS39770B-page 86
WREN
FREE
GIE
; write 55h
WR
GIE
; write 0AAh
; start erase (CPU stall)
; re-enable interrupts
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
6.5
Writing to Flash Program Memory
The on-chip timer controls the write time. The
write/erase voltages are generated by an on-chip
charge pump, rated to operate over the voltage range
of the device.
The minimum programming block is 32 words or
64 bytes. Word or byte programming is not supported.
Table writes are used internally to load the holding
registers needed to program the Flash memory. There
are 64 holding registers used by the table writes for
programming.
Note 1: Unlike previous PIC® devices, members
of the PIC18F85J90 family do not reset
the holding registers after a write occurs.
The holding registers must be cleared or
overwritten before a programming
sequence.
Since the Table Latch (TABLAT) is only a single byte,
the TBLWT instruction may need to be executed 64
times for each programming operation. All of the table
write operations will essentially be short writes because
only the holding registers are written. At the end of
updating the 64 holding registers, the EECON1 register
must be written to in order to start the programming
operation with a long write.
2: To maintain the endurance of the program
memory cells, each Flash byte should not
be programmed more than one time
between erase operations. Before
attempting to modify the contents of the
target cell a second time, a Row Erase of
the target row, or a Bulk Erase of the
entire memory, must be performed.
The long write is necessary for programming the internal Flash. Instruction execution is halted while in a long
write cycle. The long write will be terminated by the
internal programming timer.
FIGURE 6-5:
TABLE WRITES TO FLASH PROGRAM MEMORY
TABLAT
Write Register
8
8
TBLPTR = xxxxx0
8
TBLPTR = xxxxx1
Holding Register
TBLPTR = xxxx3F
TBLPTR = xxxxx2
Holding Register
8
Holding Register
Holding Register
Program Memory
6.5.1
FLASH PROGRAM MEMORY WRITE
SEQUENCE
The sequence of events for programming an internal
program memory location should be:
1.
2.
3.
4.
5.
6.
7.
Read 1024 bytes into RAM.
Update data values in RAM as necessary.
Load Table Pointer register with address being
erased.
Execute the Row Erase procedure.
Load Table Pointer register with address of first
byte being written, minus 1.
Write the 64 bytes into the holding registers with
auto-increment.
Set the WREN bit (EECON1<2>) to enable byte
writes.
© 2007 Microchip Technology Inc.
8.
9.
10.
11.
12.
Disable interrupts.
Write 55h to EECON2.
Write 0AAh to EECON2.
Set the WR bit. This will begin the write cycle.
The CPU will stall for duration of the write for TIW
(see parameter D133A).
13. Re-enable interrupts.
14. Repeat steps 6 through 13 until all 1024 bytes
are written to program memory.
15. Verify the memory (table read).
An example of the required code is shown in
Example 6-3 on the following page.
Note:
Preliminary
Before setting the WR bit, the Table
Pointer address needs to be within the
intended address range of the 64 bytes in
the holding register.
DS39770B-page 87
PIC18F85J90 FAMILY
EXAMPLE 6-3:
WRITING TO FLASH PROGRAM MEMORY
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
CODE_ADDR_UPPER
TBLPTRU
CODE_ADDR_HIGH
TBLPTRH
CODE_ADDR_LOW
TBLPTRL
; Load TBLPTR with the base address
; of the memory block, minus 1
BSF
BSF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
BSF
MOVLW
MOVWF
EECON1, WREN
EECON1, FREE
INTCON, GIE
55h
EECON2
0AAh
EECON2
EECON1, WR
INTCON, GIE
D'16'
WRITE_COUNTER
; enable write to memory
; enable Row Erase operation
; disable interrupts
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
D'64'
COUNTER
BUFFER_ADDR_HIGH
FSR0H
BUFFER_ADDR_LOW
FSR0L
ERASE_BLOCK
; write 55h
; write 0AAh
; start erase (CPU stall)
; re-enable interrupts
; Need to write 16 blocks of 64 to write
; one erase block of 1024
RESTART_BUFFER
; point to buffer
FILL_BUFFER
...
; read the new data from I2C, SPI,
; PSP, USART, etc.
WRITE_BUFFER
MOVLW
MOVWF
WRITE_BYTE_TO_HREGS
MOVFF
MOVWF
TBLWT+*
D’64
COUNTER
; number of bytes in holding register
POSTINC0, WREG
TABLAT
;
;
;
;
;
DECFSZ COUNTER
BRA
WRITE_BYTE_TO_HREGS
get low byte of buffer data
present data to table latch
write data, perform a short write
to internal TBLWT holding register.
loop until buffers are full
PROGRAM_MEMORY
Required
Sequence
BSF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
BSF
BCF
EECON1,
INTCON,
55h
EECON2
0AAh
EECON2
EECON1,
INTCON,
EECON1,
WREN
GIE
; write 55h
WR
GIE
WREN
DECFSZ WRITE_COUNTER
BRA
RESTART_BUFFER
DS39770B-page 88
; enable write to memory
; disable interrupts
;
;
;
;
write 0AAh
start program (CPU stall)
re-enable interrupts
disable write to memory
; done with one write cycle
; if not done replacing the erase block
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
6.5.2
WRITE VERIFY
6.6
Depending on the application, good programming
practice may dictate that the value written to the
memory should be verified against the original value.
This should be used in applications where excessive
writes can stress bits near the specification limit.
6.5.3
Flash Program Operation During
Code Protection
See Section 22.6 “Program Verification and Code
Protection” for details on code protection of Flash
program memory.
UNEXPECTED TERMINATION OF
WRITE OPERATION
If a write is terminated by an unplanned event, such as
loss of power or an unexpected Reset, the memory
location just programmed should be verified and reprogrammed if needed. If the write operation is interrupted
by a MCLR Reset or a WDT Time-out Reset during
normal operation, the user can check the WRERR bit
and rewrite the location(s) as needed.
TABLE 6-2:
REGISTERS ASSOCIATED WITH PROGRAM FLASH MEMORY
Name
Bit 7
Bit 6
Bit 5
TBLPTRU
—
—
bit 21
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Program Memory Table Pointer Upper Byte (TBLPTR<20:16>)
Reset
Values on
page
51
TBPLTRH Program Memory Table Pointer High Byte (TBLPTR<15:8>)
51
TBLPTRL Program Memory Table Pointer Low Byte (TBLPTR<7:0>)
51
TABLAT
51
Program Memory Table Latch
INTCON
GIE/GIEH PEIE/GIEL TMR0IE
EECON2
EEPROM Control Register 2 (not a physical register)
EECON1
—
—
—
INT0IE
FREE
RBIE
WRERR
TMR0IF
INT0IF
RBIF
51
53
WREN
WR
—
53
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used during program memory access.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 89
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 90
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
7.0
8 x 8 HARDWARE MULTIPLIER
7.1
Introduction
EXAMPLE 7-1:
MOVF
MULWF
All PIC18 devices include an 8 x 8 hardware multiplier
as part of the ALU. The multiplier performs an unsigned
operation and yields a 16-bit result that is stored in the
Product register pair, PRODH:PRODL. The multiplier’s
operation does not affect any flags in the STATUS
register.
ARG1, W
ARG2
EXAMPLE 7-2:
Making multiplication a hardware operation allows it to
be completed in a single instruction cycle. This has the
advantages of higher computational throughput and
reduced code size for multiplication algorithms and
allows the PIC18 devices to be used in many applications previously reserved for digital signal processors.
A comparison of various hardware and software
multiply operations, along with the savings in memory
and execution time, is shown in Table 7-1.
7.2
8 x 8 UNSIGNED
MULTIPLY ROUTINE
;
; ARG1 * ARG2 ->
; PRODH:PRODL
8 x 8 SIGNED MULTIPLY
ROUTINE
MOVF
MULWF
ARG1, W
ARG2
BTFSC
SUBWF
ARG2, SB
PRODH, F
MOVF
BTFSC
SUBWF
ARG2, W
ARG1, SB
PRODH, F
;
;
;
;
;
ARG1 * ARG2 ->
PRODH:PRODL
Test Sign Bit
PRODH = PRODH
- ARG1
; Test Sign Bit
; PRODH = PRODH
;
- ARG2
Operation
Example 7-1 shows the instruction sequence for an 8 x 8
unsigned multiplication. Only one instruction is required
when one of the arguments is already loaded in the
WREG register.
Example 7-2 shows the sequence to do an 8 x 8 signed
multiplication. To account for the sign bits of the arguments, each argument’s Most Significant bit (MSb) is
tested and the appropriate subtractions are done.
TABLE 7-1:
PERFORMANCE COMPARISON FOR VARIOUS MULTIPLY OPERATIONS
Routine
8 x 8 unsigned
8 x 8 signed
16 x 16 unsigned
16 x 16 signed
Multiply Method
Without hardware multiply
Program
Memory
(Words)
Cycles
(Max)
@ 40 MHz
@ 10 MHz
@ 4 MHz
13
69
6.9 μs
27.6 μs
69 μs
Time
Hardware multiply
1
1
100 ns
400 ns
1 μs
Without hardware multiply
33
91
9.1 μs
36.4 μs
91 μs
Hardware multiply
6
6
600 ns
2.4 μs
6 μs
Without hardware multiply
21
242
24.2 μs
96.8 μs
242 μs
Hardware multiply
28
28
2.8 μs
11.2 μs
28 μs
Without hardware multiply
52
254
25.4 μs
102.6 μs
254 μs
Hardware multiply
35
40
4.0 μs
16.0 μs
40 μs
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 91
PIC18F85J90 FAMILY
Example 7-3 shows the sequence to do a 16 x 16
unsigned multiplication. Equation 7-1 shows the
algorithm that is used. The 32-bit result is stored in four
registers (RES3:RES0).
EQUATION 7-1:
RES3:RES0
=
=
EXAMPLE 7-3:
16 x 16 UNSIGNED
MULTIPLICATION
ALGORITHM
ARG1H:ARG1L • ARG2H:ARG2L
(ARG1H • ARG2H • 216) +
(ARG1H • ARG2L • 28) +
(ARG1L • ARG2H • 28) +
(ARG1L • ARG2L)
EQUATION 7-2:
RES3:RES0= ARG1H:ARG1L • ARG2H:ARG2L
= (ARG1H • ARG2H • 216) +
(ARG1H • ARG2L • 28) +
(ARG1L • ARG2H • 28) +
(ARG1L • ARG2L) +
(-1 • ARG2H<7> • ARG1H:ARG1L • 216) +
(-1 • ARG1H<7> • ARG2H:ARG2L • 216)
EXAMPLE 7-4:
16 x 16 UNSIGNED
MULTIPLY ROUTINE
MOVF
MULWF
ARG1L, W
ARG2L
MOVFF
MOVFF
PRODH, RES1
PRODL, RES0
MOVF
MULWF
ARG1H, W
ARG2H
MOVFF
MOVFF
PRODH, RES3
PRODL, RES2
MOVF
MULWF
ARG1L, W
ARG2H
MOVF
ADDWF
MOVF
ADDWFC
CLRF
ADDWFC
PRODL, W
RES1, F
PRODH, W
RES2, F
WREG
RES3, F
MOVF
MULWF
ARG1H, W
ARG2L
MOVF
ADDWF
MOVF
ADDWFC
CLRF
ADDWFC
PRODL, W
RES1, F
PRODH, W
RES2, F
WREG
RES3, F
; ARG1L * ARG2L->
; PRODH:PRODL
;
;
ARG1L * ARG2H->
PRODH:PRODL
Add cross
products
ARG1H * ARG2L->
PRODH:PRODL
Add cross
products
MOVFF
MOVFF
PRODH, RES1
PRODL, RES0
MOVF
MULWF
ARG1H, W
ARG2H
MOVFF
MOVFF
PRODH, RES3
PRODL, RES2
MOVF
MULWF
ARG1L, W
ARG2H
MOVF
ADDWF
MOVF
ADDWFC
CLRF
ADDWFC
PRODL, W
RES1, F
PRODH, W
RES2, F
WREG
RES3, F
MOVF
MULWF
ARG1H, W
ARG2L
MOVF
ADDWF
MOVF
ADDWFC
CLRF
ADDWFC
PRODL, W
RES1, F
PRODH, W
RES2, F
WREG
RES3, F
BTFSS
BRA
MOVF
SUBWF
MOVF
SUBWFB
ARG2H, 7
SIGN_ARG1
ARG1L, W
RES2
ARG1H, W
RES3
; ARG2H:ARG2L neg?
; no, check ARG1
;
;
;
ARG1H, 7
CONT_CODE
ARG2L, W
RES2
ARG2H, W
RES3
; ARG1H:ARG1L neg?
; no, done
;
;
;
; ARG1L * ARG2L ->
; PRODH:PRODL
;
;
; ARG1H * ARG2H ->
; PRODH:PRODL
;
;
;
;
;
;
;
;
;
;
ARG1L * ARG2H ->
PRODH:PRODL
Add cross
products
;
;
;
;
;
;
;
;
;
ARG1H * ARG2L ->
PRODH:PRODL
Add cross
products
;
Example 7-4 shows the sequence to do a 16 x 16
signed multiply. Equation 7-2 shows the algorithm
used. The 32-bit result is stored in four registers
(RES3:RES0). To account for the sign bits of the
arguments, the MSb for each argument pair is tested
and the appropriate subtractions are done.
DS39770B-page 92
ARG1L, W
ARG2L
;
;
;
;
;
;
;
;
;
;
;
MOVF
MULWF
;
;
;
;
;
;
;
;
;
;
16 x 16 SIGNED
MULTIPLY ROUTINE
;
;
; ARG1H * ARG2H->
; PRODH:PRODL
;
;
16 x 16 SIGNED
MULTIPLICATION
ALGORITHM
;
SIGN_ARG1
BTFSS
BRA
MOVF
SUBWF
MOVF
SUBWFB
;
CONT_CODE
:
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
8.0
INTERRUPTS
Members of the PIC18F85J90 family of devices have
multiple interrupt sources and an interrupt priority
feature that allows most interrupt sources to be
assigned a high priority level or a low priority level. The
high priority interrupt vector is at 0008h and the low
priority interrupt vector is at 0018h. High priority interrupt events will interrupt any low priority interrupts that
may be in progress.
There are thirteen registers which are used to control
interrupt operation. These registers are:
•
•
•
•
•
•
•
RCON
INTCON
INTCON2
INTCON3
PIR1, PIR2, PIR3
PIE1, PIE2, PIE3
IPR1, IPR2, IPR3
It is recommended that the Microchip header files
supplied with MPLAB® IDE be used for the symbolic bit
names in these registers. This allows the
assembler/compiler to automatically take care of the
placement of these bits within the specified register.
In general, interrupt sources have three bits to control
their operation. They are:
• Flag bit to indicate that an interrupt event
occurred
• Enable bit that allows program execution to
branch to the interrupt vector address when the
flag bit is set
• Priority bit to select high priority or low priority
When the IPEN bit is cleared (default state), the
interrupt priority feature is disabled and interrupts are
compatible with PIC® mid-range devices. In
Compatibility mode, the interrupt priority bits for each
source have no effect. INTCON<6> is the PEIE bit
which enables/disables all peripheral interrupt sources.
INTCON<7> is the GIE bit which enables/disables all
interrupt sources. All interrupts branch to address
0008h in Compatibility mode.
When an interrupt is responded to, the global interrupt
enable bit is cleared to disable further interrupts. If the
IPEN bit is cleared, this is the GIE bit. If interrupt priority
levels are used, this will be either the GIEH or GIEL bit.
High priority interrupt sources can interrupt a low
priority interrupt. Low priority interrupts are not
processed while high priority interrupts are in progress.
The return address is pushed onto the stack and the
PC is loaded with the interrupt vector address (0008h
or 0018h). Once in the Interrupt Service Routine, the
source(s) of the interrupt can be determined by polling
the interrupt flag bits. The interrupt flag bits must be
cleared in software before re-enabling interrupts to
avoid recursive interrupts.
The “return from interrupt” instruction, RETFIE, exits
the interrupt routine and sets the GIE bit (GIEH or GIEL
if priority levels are used) which re-enables interrupts.
For external interrupt events, such as the INT pins or
the PORTB input change interrupt, the interrupt latency
will be three to four instruction cycles. The exact
latency is the same for one or two-cycle instructions.
Individual interrupt flag bits are set regardless of the
status of their corresponding enable bit or the GIE bit.
Note:
The interrupt priority feature is enabled by setting the
IPEN bit (RCON<7>). When interrupt priority is
enabled, there are two bits which enable interrupts
globally. Setting the GIEH bit (INTCON<7>) enables all
interrupts that have the priority bit set (high priority).
Setting the GIEL bit (INTCON<6>) enables all
interrupts that have the priority bit cleared (low priority).
When the interrupt flag, enable bit and appropriate
global interrupt enable bit are set, the interrupt will
vector immediately to address 0008h or 0018h,
depending on the priority bit setting. Individual
interrupts can be disabled through their corresponding
enable bits.
© 2007 Microchip Technology Inc.
Preliminary
Do not use the MOVFF instruction to modify
any of the Interrupt Control registers while
any interrupt is enabled. Doing so may
cause erratic microcontroller behavior.
DS39770B-page 93
PIC18F85J90 FAMILY
FIGURE 8-1:
PIC18F85J90 FAMILY INTERRUPT LOGIC
PIR1<6:3,1:0>
PIE1<6:3,1:0>
IPR1<6:3,1:0>
PIR2<7:6,3:1>
PIE2<7:6 3:1>
IPR2<7:6,3:1>
Wake-up if in
Idle or Sleep modes
TMR0IF
TMR0IE
TMR0IP
RBIF
RBIE
RBIP
INT0IF
INT0IE
INT1IF
INT1IE
INT1IP
INT2IF
INT2IE
INT2IP
INT3IF
INT3IE
INT3IP
Interrupt to CPU
Vector to Location
0008h
GIE/GIEH
IPEN
PIR3<6:4,2:1>
PIE3<6:4,2:1>
IPR3<6:4,2:1>
IPEN
PEIE/GIEL
IPEN
High Priority Interrupt Generation
Low Priority Interrupt Generation
PIR1<6:3,1:0>
PIE1<6:3,1:0>
IPR1<6:3,1:0>
PIR2<7:6,3:1>
PIE2<7:6,3:1>
IPR2<7:6,3:1>
PIR3<6:4,2:1>
PIE3<6:4,2:1>
IPR3<6:4,2:1>
TMR0IF
TMR0IE
TMR0IP
RBIF
RBIE
RBIP
INT1IF
INT1IE
INT1IP
INT2IF
INT2IE
INT2IP
INT3IF
INT3IE
INT3IP
DS39770B-page 94
Preliminary
Interrupt to CPU
Vector to Location
0018h
IPEN
GIE/GIEH
PEIE/GIEL
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
8.1
INTCON Registers
Note:
The INTCON registers are readable and writable
registers which contain various enable, priority and flag
bits.
REGISTER 8-1:
Interrupt flag bits are set when an interrupt
condition occurs regardless of the state of
its corresponding enable bit or the global
interrupt enable bit. User software should
ensure the appropriate interrupt flag bits
are clear prior to enabling an interrupt.
This feature allows for software polling.
INTCON: INTERRUPT CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-x
GIE/GIEH
PEIE/GIEL
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
GIE/GIEH: Global Interrupt Enable bit
When IPEN = 0:
1 = Enables all unmasked interrupts
0 = Disables all interrupts
When IPEN = 1:
1 = Enables all high priority interrupts
0 = Disables all interrupts
bit 6
PEIE/GIEL: Peripheral Interrupt Enable bit
When IPEN = 0:
1 = Enables all unmasked peripheral interrupts
0 = Disables all peripheral interrupts
When IPEN = 1:
1 = Enables all low priority peripheral interrupts
0 = Disables all low priority peripheral interrupts
bit 5
TMR0IE: TMR0 Overflow Interrupt Enable bit
1 = Enables the TMR0 overflow interrupt
0 = Disables the TMR0 overflow interrupt
bit 4
INT0IE: INT0 External Interrupt Enable bit
1 = Enables the INT0 external interrupt
0 = Disables the INT0 external interrupt
bit 3
RBIE: RB Port Change Interrupt Enable bit
1 = Enables the RB port change interrupt
0 = Disables the RB port change interrupt
bit 2
TMR0IF: TMR0 Overflow Interrupt Flag bit
1 = TMR0 register has overflowed (must be cleared in software)
0 = TMR0 register did not overflow
bit 1
INT0IF: INT0 External Interrupt Flag bit
1 = The INT0 external interrupt occurred (must be cleared in software)
0 = The INT0 external interrupt did not occur
bit 0
RBIF: RB Port Change Interrupt Flag bit(1)
1 = At least one of the RB7:RB4 pins changed state (must be cleared in software)
0 = None of the RB7:RB4 pins have changed state
Note 1:
A mismatch condition will continue to set this bit. Reading PORTB will end the mismatch condition and
allow the bit to be cleared.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 95
PIC18F85J90 FAMILY
REGISTER 8-2:
INTCON2: INTERRUPT CONTROL REGISTER 2
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
RBPU
INTEDG0
INTEDG1
INTEDG2
INTEDG3
TMR0IP
INT3IP
RBIP
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
RBPU: PORTB Pull-up Enable bit
1 = All PORTB pull-ups are disabled
0 = PORTB pull-ups are enabled by individual port latch values
bit 6
INTEDG0: External Interrupt 0 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
bit 5
INTEDG1: External Interrupt 1 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
bit 4
INTEDG2: External Interrupt 2 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
bit 3
INTEDG3: External Interrupt 3 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
bit 2
TMR0IP: TMR0 Overflow Interrupt Priority bit
1 = High priority
0 = Low priority
bit 1
INT3IP: INT3 External Interrupt Priority bit
1 = High priority
0 = Low priority
bit 0
RBIP: RB Port Change Interrupt Priority bit
1 = High priority
0 = Low priority
Note:
x = Bit is unknown
Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding
enable bit or the global interrupt enable bit. User software should ensure the appropriate interrupt flag bits
are clear prior to enabling an interrupt. This feature allows for software polling.
DS39770B-page 96
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 8-3:
INTCON3: INTERRUPT CONTROL REGISTER 3
R/W-1
R/W-1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INT2IP
INT1IP
INT3IE
INT2IE
INT1IE
INT3IF
INT2IF
INT1IF
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
INT2IP: INT2 External Interrupt Priority bit
1 = High priority
0 = Low priority
bit 6
INT1IP: INT1 External Interrupt Priority bit
1 = High priority
0 = Low priority
bit 5
INT3IE: INT3 External Interrupt Enable bit
1 = Enables the INT3 external interrupt
0 = Disables the INT3 external interrupt
bit 4
INT2IE: INT2 External Interrupt Enable bit
1 = Enables the INT2 external interrupt
0 = Disables the INT2 external interrupt
bit 3
INT1IE: INT1 External Interrupt Enable bit
1 = Enables the INT1 external interrupt
0 = Disables the INT1 external interrupt
bit 2
INT3IF: INT3 External Interrupt Flag bit
1 = The INT3 external interrupt occurred (must be cleared in software)
0 = The INT3 external interrupt did not occur
bit 1
INT2IF: INT2 External Interrupt Flag bit
1 = The INT2 external interrupt occurred (must be cleared in software)
0 = The INT2 external interrupt did not occur
bit 0
INT1IF: INT1 External Interrupt Flag bit
1 = The INT1 external interrupt occurred (must be cleared in software)
0 = The INT1 external interrupt did not occur
Note:
x = Bit is unknown
Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding
enable bit or the global interrupt enable bit. User software should ensure the appropriate interrupt flag bits
are clear prior to enabling an interrupt. This feature allows for software polling.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 97
PIC18F85J90 FAMILY
8.2
PIR Registers
The PIR registers contain the individual flag bits for the
peripheral interrupts. Due to the number of peripheral
interrupt sources, there are three Peripheral Interrupt
Request (Flag) registers (PIR1, PIR2, PIR3).
REGISTER 8-4:
Note 1: Interrupt flag bits are set when an interrupt
condition occurs regardless of the state of
its corresponding enable bit or the Global
Interrupt Enable bit, GIE (INTCON<7>).
2: User software should ensure the
appropriate interrupt flag bits are cleared
prior to enabling an interrupt and after
servicing that interrupt.
PIR1: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 1
U-0
R/W-0
R-0
R-0
R/W-0
U-0
R/W-0
R/W-0
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
Unimplemented: Read as ‘0’
bit 6
ADIF: A/D Converter Interrupt Flag bit
1 = An A/D conversion completed (must be cleared in software)
0 = The A/D conversion is not complete
bit 5
RC1IF: EUSART Receive Interrupt Flag bit
1 = The EUSART receive buffer, RCREG1, is full (cleared when RCREG1 is read)
0 = The EUSART receive buffer is empty
bit 4
TX1IF: EUSART Transmit Interrupt Flag bit
1 = The EUSART transmit buffer, TXREG1, is empty (cleared when TXREG1 is written)
0 = The EUSART transmit buffer is full
bit 3
SSPIF: Master Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
bit 2
Unimplemented: Read as ‘0’
bit 1
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
bit 0
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflowed (must be cleared in software)
0 = TMR1 register did not overflow
DS39770B-page 98
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 8-5:
PIR2: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 2
R/W-0
R/W-0
U-0
U-0
R/W-0
R/W-0
R/W-0
U-0
OSCFIF
CMIF
—
—
BCLIF
LVDIF
TMR3IF
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
OSCFIF: Oscillator Fail Interrupt Flag bit
1 = Device oscillator failed, clock input has changed to INTOSC (must be cleared in software)
0 = Device clock operating
bit 6
CMIF: Comparator Interrupt Flag bit
1 = Comparator input has changed (must be cleared in software)
0 = Comparator input has not changed
bit 5-4
Unimplemented: Read as ‘0’
bit 3
BCLIF: Bus Collision Interrupt Flag bit
1 = A bus collision occurred (must be cleared in software)
0 = No bus collision occurred
bit 2
LVDIF: Low-Voltage Detect Interrupt Flag bit
1 = A low-voltage condition occurred (must be cleared in software)
0 = The device voltage is above the regulator’s low-voltage trip point
bit 1
TMR3IF: TMR3 Overflow Interrupt Flag bit
1 = TMR3 register overflowed (must be cleared in software)
0 = TMR3 register did not overflow
bit 0
Unimplemented: Read as ‘0’
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 99
PIC18F85J90 FAMILY
REGISTER 8-6:
PIR3: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 3
U-0
R/W-0
R-0
R-0
U-0
R/W-0
R/W-0
U-0
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
Unimplemented: Read as ‘0’
bit 6
LCDIF: LCD Interrupt Flag bit (valid when Type-B waveform with Non-Static mode is selected)
1 = LCD data of all COMs is output (must be cleared in software)
0 = LCD data of all COMs is not yet output
bit 5
RC2IF: AUSART Receive Interrupt Flag bit
1 = The AUSART receive buffer, RCREG2, is full (cleared when RCREG2 is read)
0 = The AUSART receive buffer is empty
bit 4
TX2IF: AUSART Transmit Interrupt Flag bit
1 = The AUSART transmit buffer, TXREG2, is empty (cleared when TXREG2 is written)
0 = The AUSART transmit buffer is full
bit 3
Unimplemented: Read as ‘0’
bit 2
CCP2IF: CCP2 Interrupt Flag bit
Capture mode:
1 = A TMR1/TMR3 register capture occurred (must be cleared in software)
0 = No TMR1/TMR3 register capture occurred
Compare mode:
1 = A TMR1/TMR3 register compare match occurred (must be cleared in software)
0 = No TMR1/TMR3 register compare match occurred
PWM mode:
Unused in this mode.
bit 1
CCP1IF: CCP1 Interrupt Flag bit
Capture mode:
1 = A TMR1/TMR3 register capture occurred (must be cleared in software)
0 = No TMR1/TMR3 register capture occurred
Compare mode:
1 = A TMR1/TMR3 register compare match occurred (must be cleared in software)
0 = No TMR1/TMR3 register compare match occurred
PWM mode:
Unused in this mode.
bit 0
Unimplemented: Read as ‘0’
DS39770B-page 100
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
8.3
PIE Registers
The PIE registers contain the individual enable bits for
the peripheral interrupts. Due to the number of
peripheral interrupt sources, there are three Peripheral
Interrupt Enable registers (PIE1, PIE2, PIE3). When
IPEN = 0, the PEIE bit must be set to enable any of
these peripheral interrupts.
REGISTER 8-7:
PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1
U-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
Unimplemented: Read as ‘0’
bit 6
ADIE: A/D Converter Interrupt Enable bit
1 = Enables the A/D interrupt
0 = Disables the A/D interrupt
bit 5
RC1IE: EUSART Receive Interrupt Enable bit
1 = Enables the EUSART receive interrupt
0 = Disables the EUSART receive interrupt
bit 4
TX1IE: EUSART Transmit Interrupt Enable bit
1 = Enables the EUSART transmit interrupt
0 = Disables the EUSART transmit interrupt
bit 3
SSPIE: Master Synchronous Serial Port Interrupt Enable bit
1 = Enables the MSSP interrupt
0 = Disables the MSSP interrupt
bit 2
Unimplemented: Read as ‘0’
bit 1
TMR2IE: TMR2 to PR2 Match Interrupt Enable bit
1 = Enables the TMR2 to PR2 match interrupt
0 = Disables the TMR2 to PR2 match interrupt
bit 0
TMR1IE: TMR1 Overflow Interrupt Enable bit
1 = Enables the TMR1 overflow interrupt
0 = Disables the TMR1 overflow interrupt
© 2007 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39770B-page 101
PIC18F85J90 FAMILY
REGISTER 8-8:
PIE2: PERIPHERAL INTERRUPT ENABLE REGISTER 2
R/W-0
R/W-0
U-0
U-0
R/W-0
R/W-0
R/W-0
U-0
OSCFIE
CMIE
—
—
BCLIE
LVDIE
TMR3IE
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
OSCFIE: Oscillator Fail Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 6
CMIE: Comparator Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 5-4
Unimplemented: Read as ‘0’
bit 3
BCLIE: Bus Collision Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 2
LVDIE: Low-Voltage Detect Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 1
TMR3IE: TMR3 Overflow Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 0
Unimplemented: Read as ‘0’
DS39770B-page 102
Preliminary
x = Bit is unknown
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 8-9:
PIE3: PERIPHERAL INTERRUPT ENABLE REGISTER 3
U-0
R/W-0
R-0
R-0
U-0
R/W-0
R/W-0
U-0
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
Unimplemented: Read as ‘0’
bit 6
LCDIE: LCD Interrupt Enable bit (valid when Type-B waveform with Non-Static mode is selected)
1 = Enabled
0 = Disabled
bit 5
RC2IE: AUSART Receive Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 4
TX2IE: AUSART Transmit Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 3
Unimplemented: Read as ‘0’
bit 2
CCP2IE: CCP2 Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 1
CCP1IE: CCP1 Interrupt Enable bit
1 = Enables the CCP1 interrupt
0 = Disables the CCP1 interrupt
bit 0
Unimplemented: Read as ‘0’
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 103
PIC18F85J90 FAMILY
8.4
IPR Registers
The IPR registers contain the individual priority bits for
the peripheral interrupts. Due to the number of
peripheral interrupt sources, there are three Peripheral
Interrupt Priority registers (IPR1, IPR2, IPR3). Using
the priority bits requires that the Interrupt Priority
Enable (IPEN) bit be set.
REGISTER 8-10:
IPR1: PERIPHERAL INTERRUPT PRIORITY REGISTER 1
U-0
R/W-1
R/W-1
R/W-1
R/W-1
U-0
R/W-1
R/W-1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
Unimplemented: Read as ‘0’
bit 6
ADIP: A/D Converter Interrupt Priority bit
1 = High priority
0 = Low priority
bit 5
RC1IP: EUSART Receive Interrupt Priority bit
1 = High priority
0 = Low priority
bit 4
TX1IP: EUSART Transmit Interrupt Priority bit
x = Bit is unknown
1 = High priority
0 = Low priority
bit 3
SSPIP: Master Synchronous Serial Port Interrupt Priority bit
1 = High priority
0 = Low priority
bit 2
Unimplemented: Read as ‘0’
bit 1
TMR2IP: TMR2 to PR2 Match Interrupt Priority bit
1 = High priority
0 = Low priority
bit 0
TMR1IP: TMR1 Overflow Interrupt Priority bit
1 = High priority
0 = Low priority
DS39770B-page 104
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 8-11:
IPR2: PERIPHERAL INTERRUPT PRIORITY REGISTER 2
R/W-1
R/W-1
U-0
U-0
R/W-1
R/W-1
R/W-1
U-0
OSCFIP
CMIP
—
—
BCLIP
LVDIP
TMR3IP
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
OSCFIP: Oscillator Fail Interrupt Priority bit
1 = High priority
0 = Low priority
bit 6
CMIP: Comparator Interrupt Priority bit
1 = High priority
0 = Low priority
bit 5-4
Unimplemented: Read as ‘0’
bit 3
BCLIP: Bus Collision Interrupt Priority bit
1 = High priority
0 = Low priority
bit 2
LVDIP: Low-Voltage Detect Interrupt Priority bit
1 = High priority
0 = Low priority
bit 1
TMR3IP: TMR3 Overflow Interrupt Priority bit
1 = High priority
0 = Low priority
bit 0
Unimplemented: Read as ‘0’
© 2007 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39770B-page 105
PIC18F85J90 FAMILY
REGISTER 8-12:
IPR3: PERIPHERAL INTERRUPT PRIORITY REGISTER 3
U-0
R/W-0
R-0
R-0
U-0
R/W-1
R/W-1
U-0
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
Unimplemented: Read as ‘0’
bit 6
LCDIP: LCD Interrupt Priority bit (valid when Type-B waveform with Non-Static mode is selected)
1 = High priority
0 = Low priority
bit 5
RC2IP: AUSART Receive Priority Flag bit
1 = High priority
0 = Low priority
bit 4
TX2IP: AUSART Transmit Interrupt Priority bit
1 = High priority
0 = Low priority
bit 3
Unimplemented: Read as ‘0’
bit
CCP2IP: CCP2 Interrupt Priority bit
1 = High priority
0 = Low priority
bit
CCP1IP: CCP1 Interrupt Priority bit
1 = High priority
0 = Low priority
bit 0
Unimplemented: Read as ‘0’
DS39770B-page 106
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
8.5
RCON Register
The RCON register contains bits used to determine the
cause of the last Reset or wake-up from Idle or Sleep
modes. RCON also contains the bit that enables
interrupt priorities (IPEN).
REGISTER 8-13:
RCON: RESET CONTROL REGISTER
R/W-0
U-0
U-0
R/W-1
R-1
R-1
R/W-0
R/W-0
IPEN
—
—
RI
TO
PD
POR
BOR
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode)
bit 6-5
Unimplemented: Read as ‘0’
bit 4
RI: RESET Instruction Flag bit
For details of bit operation, see Register 4-1.
bit 3
TO: Watchdog Timer Time-out Flag bit
For details of bit operation, see Register 4-1.
bit 2
PD: Power-Down Detection Flag bit
For details of bit operation, see Register 4-1.
bit 1
POR: Power-on Reset Status bit
For details of bit operation, see Register 4-1.
bit 0
BOR: Brown-out Reset Status bit
For details of bit operation, see Register 4-1.
© 2007 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39770B-page 107
PIC18F85J90 FAMILY
8.6
INTx Pin Interrupts
8.7
External interrupts on the RB0/INT0, RB1/INT1,
RB2/INT2 and RB3/INT3 pins are edge-triggered. If the
corresponding INTEDGx bit in the INTCON2 register is
set (= 1), the interrupt is triggered by a rising edge; if
the bit is clear, the trigger is on the falling edge. When
a valid edge appears on the RBx/INTx pin, the
corresponding flag bit, INTxIF, is set. This interrupt can
be disabled by clearing the corresponding enable bit,
INTxIE. Flag bit, INTxIF, must be cleared in software in
the Interrupt Service Routine before re-enabling the
interrupt.
All external interrupts (INT0, INT1, INT2 and INT3) can
wake-up the processor from the power-managed
modes if bit INTxIE was set prior to going into the
power-managed modes. If the Global Interrupt Enable
bit, GIE, is set, the processor will branch to the interrupt
vector following wake-up.
Interrupt priority for INT1, INT2 and INT3 is determined
by the value contained in the interrupt priority bits,
INT1IP (INTCON3<6>), INT2IP (INTCON3<7>) and
INT3IP (INTCON2<1>). There is no priority bit
associated with INT0. It is always a high priority
interrupt source.
EXAMPLE 8-1:
MOVWF
MOVFF
MOVFF
;
; USER
;
MOVFF
MOVF
MOVFF
TMR0 Interrupt
In 8-bit mode (which is the default), an overflow in the
TMR0 register (FFh → 00h) will set flag bit, TMR0IF. In
16-bit mode, an overflow in the TMR0H:TMR0L register
pair (FFFFh → 0000h) will set TMR0IF. The interrupt can
be enabled/disabled by setting/clearing enable bit,
TMR0IE (INTCON<5>). Interrupt priority for Timer0 is
determined by the value contained in the interrupt priority
bit, TMR0IP (INTCON2<2>). See Section 10.0 “Timer0
Module” for further details on the Timer0 module.
8.8
PORTB Interrupt-on-Change
An input change on PORTB<7:4> sets flag bit, RBIF
(INTCON<0>). The interrupt can be enabled/disabled
by setting/clearing enable bit, RBIE (INTCON<3>).
Interrupt priority for PORTB interrupt-on-change is
determined by the value contained in the interrupt
priority bit, RBIP (INTCON2<0>).
8.9
Context Saving During Interrupts
During interrupts, the return PC address is saved on
the stack. Additionally, the WREG, STATUS and BSR
registers are saved on the Fast Return Stack. If a fast
return from interrupt is not used (see Section 5.3
“Data Memory Organization”), the user may need to
save the WREG, STATUS and BSR registers on entry
to the Interrupt Service Routine. Depending on the
user’s application, other registers may also need to be
saved. Example 8-1 saves and restores the WREG,
STATUS and BSR registers during an Interrupt Service
Routine.
SAVING STATUS, WREG AND BSR REGISTERS IN RAM
W_TEMP
STATUS, STATUS_TEMP
BSR, BSR_TEMP
; W_TEMP is in virtual bank
; STATUS_TEMP located anywhere
; BSR_TMEP located anywhere
ISR CODE
BSR_TEMP, BSR
W_TEMP, W
STATUS_TEMP, STATUS
DS39770B-page 108
; Restore BSR
; Restore WREG
; Restore STATUS
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
9.0
I/O PORTS
9.1
Depending on the device selected and features
enabled, there are up to nine ports available. Some
pins of the I/O ports are multiplexed with an alternate
function from the peripheral features on the device. In
general, when a peripheral is enabled, that pin may not
be used as a general purpose I/O pin.
Each port has three memory mapped registers for its
operation:
• TRIS register (Data Direction register)
• PORT register (reads the levels on the pins of the
device)
• LAT register (Output Latch register)
Reading the PORT register reads the current status of
the pins, whereas writing to the PORT register writes to
the Output Latch (LAT) register.
Setting a TRIS bit (= 1) makes the corresponding
PORT pin an input (i.e., put the corresponding output
driver in a high-impedance mode). Clearing a TRIS bit
(= 0) makes the corresponding PORT pin an output
(i.e., put the contents of the corresponding LAT bit on
the selected pin).
The Data Latch (LAT register) is useful for
read-modify-write operations on the value that the I/O
pins are driving. Read-modify-write operations on the
LAT register read and write the latched output value for
the PORT register.
A simplified model of a generic I/O port, without the
interfaces to other peripherals, is shown in Figure 9-1.
I/O Port Pin Capabilities
When developing an application, the capabilities of the
port pins must be considered. Outputs on some pins
have higher output drive strength than others. Similarly,
some pins can tolerate higher than VDD input levels.
9.1.1
INPUT PINS AND VOLTAGE
CONSIDERATIONS
The voltage tolerance of pins used as device inputs is
dependent on the pin’s input function. Pins that are used
as digital only inputs are able to handle DC voltages up
to 5.5V, a level typical for digital logic circuits. In contrast,
pins that also have analog input functions of any kind
can only tolerate voltages up to VDD. Voltage excursions
beyond VDD on these pins should be avoided.
Table 9-1 summarizes the input voltage capabilities.
Refer to Section 25.0 “Electrical Characteristics” for
more details.
TABLE 9-1:
PORT or Pin
PORTA<7:0>
INPUT VOLTAGE TOLERANCE
Tolerated
Input
Description
VDD
Only VDD input levels
tolerated.
5.5V
Tolerates input levels
above VDD, useful for
most standard logic.
PORTC<1:0>
PORTF<7:1>
PORTB<7:0>
PORTC<7:2>
PORTD<7:0>
PORTE<7:0>
FIGURE 9-1:
GENERIC I/O PORT
OPERATION
PORTG<4:0>
PORTH<7:0>(1)
PORTJ<7:0>(1)
RD LAT
Note 1:
Data
Bus
D
9.1.2
Q
(1)
I/O pin
WR LAT
or PORT
CKx
Data Latch
D
WR TRIS
Q
CKx
TRIS Latch
Input
Buffer
RD TRIS
Q
D
ENEN
RD PORT
Note 1:
I/O pins have diode protection to VDD and VSS.
© 2007 Microchip Technology Inc.
Not available on 64-pin devices.
PIN OUTPUT DRIVE
When used as digital I/O, the output pin drive strengths
vary for groups of pins intended to meet the needs for
a variety of applications. In general, there are three
classes of output pins in terms of drive capability.
PORTB and PORTC, as well as PORTA<7:6>, are
designed to drive higher current loads, such as LEDs.
PORTD, PORTE and PORTJ can also drive LEDs but
only those with smaller current requirements. PORTF,
PORTG and PORTH, along with PORTA<5:0>, have
the lowest drive level but are capable of driving normal
digital circuit loads with a high input impedance.
Regardless of which port it is located on, all output pins
in LCD Segment or Common mode have sufficient
output to directly drive a display.
Table 9-2 summarizes the output capabilities of the
ports. Refer to the “Absolute Maximum Ratings” in
Section 25.0 “Electrical Characteristics” for more
details.
Preliminary
DS39770B-page 109
PIC18F85J90 FAMILY
TABLE 9-2:
OUTPUT DRIVE LEVELS FOR
VARIOUS PORTS
Low
Medium
High
PORTA<5:0>
PORTD
PORTA<7:6>
PORTF
PORTE
PORTB
PORTG
PORTJ
(1)
9.1.3
RA4/T0CKI is a Schmitt Trigger input. All other PORTA
pins have TTL input levels and full CMOS output
drivers.
PORTC
Not available on 64-pin devices.
PULL-UP CONFIGURATION
Four of the I/O ports (PORTB, PORTD, PORTE and
PORTJ) implement configurable weak pull-ups on all
pins. These are internal pull-ups that allow floating
digital input signals to be pulled to a consistent level
without the use of external resistors.
The pull-ups are enabled with a single bit for each of the
ports: RBPU (INTCON2<7>) for PORTB, and RDPU,
REPU and PJPU (PORTG<7:5>) for the other ports.
9.1.4
OPEN-DRAIN OUTPUTS
The open-drain option is implemented on port pins
specifically associated with the data and clock outputs
of the USARTs, the MSSP module (in SPI mode) and
the CCP modules. This option is selectively enabled by
setting the open-drain control bit for the corresponding
module in TRISG and LATG. Their configuration is discussed in more detail in Section 9.4 “PORTC, TRISC
and LATC Registers”, Section 9.6 “PORTE, TRISE
and LATE Registers” and Section 9.8 “PORTG,
TRISG and LATG Registers”.
When the open-drain option is required, the output pin
must also be tied through an external pull-up resistor
provided by the user to a higher voltage level, up to 5V
(Figure 9-2). When a digital logic high signal is output,
it is pulled up to the higher voltage level.
USING THE OPEN-DRAIN
OUTPUT (USART SHOWN
AS EXAMPLE)
3.3V
+5V
PIC18F85J90
VDD
TXX
(at logic ‘1’)
DS39770B-page 110
The RA4 pin is multiplexed with the Timer0 clock input
and one of the LCD segment drives. RA5 and RA3:RA0
are multiplexed with analog inputs for the A/D
converter.
The operation of the analog inputs as A/D converter
inputs is selected by clearing or setting the
PCFG3:PCFG0 control bits in the ADCON1 register.
The corresponding TRISA bits control the direction of
these pins, even when they are being used as analog
inputs. The user must ensure the bits in the TRISA
register are maintained set when using them as analog
inputs.
Note:
The output pins for several peripherals are also
equipped with a configurable, open-drain output option.
This allows the peripherals to communicate with
external digital logic, operating at a higher voltage
level, without the use of level translators.
FIGURE 9-2:
RA5 and RA3:RA0 are configured as
analog inputs on any Reset and are read
as ‘0’. RA4 is configured as a digital input.
OSC2/CLKO/RA6 and OSC1/CLKI/RA7 normally
serve as the external circuit connections for the external (primary) oscillator circuit (HS Oscillator modes), or
the external clock input and output (EC Oscillator
modes). In these cases, RA6 and RA7 are not available
as digital I/O and their corresponding TRIS and LAT
bits are read as ‘0’. When the device is configured to
use INTOSC or INTRC as the default oscillator mode
(FOSC2 Configuration bit is ‘0’), RA6 and RA7 are
automatically configured as digital I/O; the oscillator
and clock in/clock out functions are disabled.
RA1, RA4 and RA5 are multiplexed with LCD segment
drives, controlled by bits in the LCDSE1 and LCDSE2
registers. I/O port functionality is only available when
the LCD segments are disabled.
EXAMPLE 9-1:
CLRF
CLRF
MOVLW
MOVWF
MOVLW
MOVWF
3.3V
PORTA, TRISA and
LATA Registers
PORTA is an 8-bit wide, bidirectional port. The corresponding Data Direction and Output Latch registers are
TRISA and LATA.
PORTH(1)
Note 1:
9.2
PORTA
;
;
LATA
;
;
07h
;
ADCON1 ;
0BFh
;
;
TRISA
;
;
INITIALIZING PORTA
Initialize PORTA by
clearing output latches
Alternate method to
clear output data latches
Configure A/D
for digital inputs
Value used to initialize
data direction
Set RA<7, 5:0> as inputs,
RA<6> as output
5V
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 9-3:
PORTA FUNCTIONS
Pin Name
Function
TRIS
Setting
I/O
I/O
Type
RA0
0
O
DIG
1
I
TTL
PORTA<0> data input; disabled when analog input enabled.
AN0
1
I
ANA
A/D input channel 0. Default input configuration on POR; does not
affect digital output.
RA1
0
O
DIG
LATA<1> data output; not affected by analog input.
1
I
TTL
PORTA<1> data input; disabled when analog input enabled.
AN1
1
I
ANA
A/D input channel 1. Default input configuration on POR; does not
affect digital output.
SEG18
x
O
ANA
LCD segment 18 output; disables all other pin functions.
RA2
0
O
DIG
LATA<2> data output; not affected by analog input.
1
I
TTL
PORTA<2> data input; disabled when analog functions enabled.
RA0/AN0
RA1/AN1/SEG18
RA2/AN2/VREF-
RA3/AN3/VREF+
RA4/T0CKI/
SEG14
TRISA
ADCON1
I
ANA
A/D input channel 2. Default input configuration on POR.
I
ANA
A/D and Comparator low reference voltage input.
RA3
0
O
DIG
LATA<3> data output; not affected by analog input.
1
I
TTL
PORTA<3> data input; disabled when analog input enabled.
AN3
1
I
ANA
A/D input channel 3. Default input configuration on POR.
VREF+
1
I
ANA
A/D and Comparator high reference voltage input.
RA4
0
O
DIG
LATA<4> data output.
1
I
ST
PORTA<4> data input. Default configuration on POR.
I
ST
x
O
ANA
LCD segment 14 output; disables all other pin functions.
Timer0 clock input.
RA5
0
O
DIG
LATA<5> data output; not affected by analog input.
1
I
TTL
PORTA<5> data input; disabled when analog input enabled.
A/D input channel 4. Default configuration on POR.
AN4
1
I
ANA
SEG15
x
O
ANA
LCD segment 15 output; disables all other pin functions.
OSC2
x
O
ANA
Main oscillator feedback output connection (HS and HSPLL modes).
CLKO
x
O
DIG
System cycle clock output (FOSC/4) (EC and ECPLL modes).
RA6
0
O
DIG
LATA<6> data output; disabled when FOSC2 Configuration bit is set.
1
I
TTL
PORTA<6> data input; disabled when FOSC2 Configuration bit is set.
OSC1
x
I
ANA
Main oscillator input connection (HS and HSPLL modes).
CLKI
x
I
ANA
Main external clock source input (EC and ECPLL modes).
RA7
0
O
DIG
LATA<7> data output; disabled when FOSC2 Configuration bit is set.
1
I
TTL
PORTA<7> data input; disabled when FOSC2 Configuration bit is set.
O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input,
TTL = TTL Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
TABLE 9-4:
LATA
1
1
x
OSC1/CLKI/RA7
PORTA
AN2
VREF-
T0CKI
OSC2/CLKO/RA6
Name
LATA<0> data output; not affected by analog input.
SEG14
RA5/AN4/SEG15
Legend:
Description
SUMMARY OF REGISTERS ASSOCIATED WITH PORTA
Bit 7
Bit 6
RA7(1)
RA6(1)
RA5
RA4
RA3
RA2
LATA7(1)
LATA6(1)
LATA5
LATA4
LATA3
LATA2
TRISA7
—
(1)
TRISA6
Bit 5
(1)
Bit 4
Bit 3
Bit 2
Bit 0
Reset Values
on page
RA1
RA0
55
LATA1
LATA0
54
Bit 1
TRISA5
TRISA4
TRISA3
TRISA2
TRISA1
TRISA0
54
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
53
LCDSE1
SE15
SE14
SE13
SE12
SE11
SE10
SE09
SE08
53
LCDSE2
SE23
SE22
SE21
SE20
SE19
SE18
SE17
SE16
53
Legend:
Note 1:
— = unimplemented, read as ‘0’. Shaded cells are not used by PORTA.
These bits are enabled depending on the oscillator mode selected. When not enabled as PORTA pins, they are
disabled and read as ‘X’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 111
PIC18F85J90 FAMILY
9.3
PORTB, TRISB and
LATB Registers
PORTB is an 8-bit wide, bidirectional port. The
corresponding Data Direction and Output Latch registers
are TRISB and LATB. All pins on PORTB are digital only
and tolerate voltages up to 5.5V.
EXAMPLE 9-2:
CLRF
PORTB
CLRF
LATB
MOVLW
0CFh
MOVWF
TRISB
INITIALIZING PORTB
;
;
;
;
;
;
;
;
;
;
;
;
This interrupt can wake the device from
power-managed modes. The user, in the Interrupt
Service Routine, can clear the interrupt in the following
manner:
Initialize PORTB by
clearing output
data latches
Alternate method
to clear output
data latches
Value used to
initialize data
direction
Set RB<3:0> as inputs
RB<5:4> as outputs
RB<7:6> as inputs
a)
b)
Any read or write of PORTB (except with the
MOVFF (ANY), PORTB instruction). This will
end the mismatch condition.
Clear flag bit, RBIF.
A mismatch condition will continue to set flag bit, RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit, RBIF, to be cleared.
Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is
performed by clearing bit RBPU (INTCON2<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on a Power-on Reset.
DS39770B-page 112
Four of the PORTB pins (RB7:RB4) have an
interrupt-on-change feature. Only pins configured as
inputs can cause this interrupt to occur (i.e., any
RB7:RB4 pin configured as an output is excluded from
the interrupt-on-change comparison). The input pins (of
RB7:RB4) are compared with the old value latched on
the last read of PORTB. The “mismatch” outputs of
RB7:RB4 are ORed together to generate the RB Port
Change Interrupt with Flag bit, RBIF (INTCON<0>).
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
RB5:RB0 are also multiplexed with LCD segment
drives, controlled by bits in the LCDSE1 and LCDSE3
registers. I/O port functionality is only available when
the LCD segments are disabled.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 9-5:
Pin Name
RB0/INT0/SEG30
RB1/INT1/SEG8
PORTB FUNCTIONS
Function
TRIS
Setting
I/O
I/O
Type
RB0
0
O
DIG
LATB<0> data output.
1
I
TTL
PORTB<0> data input; weak pull-up when RBPU bit is cleared.
INT0
1
I
ST
SEG30
x
O
ANA
LCD segment 30 output; disables all other pin functions.
RB1
0
O
DIG
LATB<1> data output.
1
I
TTL
PORTB<1> data input; weak pull-up when RBPU bit is cleared.
1
I
ST
External interrupt 1 input.
INT1
RB2/INT2/SEG9
RB3/INT3/SEG10
RB4/KBI0/SEG11
RB5/KBI1/SEG29
RB7/KBI3/PGD
Legend:
External interrupt 0 input.
SEG8
x
O
ANA
LCD segment 8 output; disables all other pin functions.
RB2
0
O
DIG
LATB<2> data output.
1
I
TTL
PORTB<2> data input; weak pull-up when RBPU bit is cleared.
External interrupt 2 input.
INT2
1
I
ST
SEG9
x
O
ANA
LCD segment 9 output; disables all other pin functions.
RB3
0
O
DIG
LATB<3> data output.
1
I
TTL
PORTB<3> data input; weak pull-up when RBPU bit is cleared.
INT3
1
I
ST
SEG10
x
O
ANA
LCD segment 10 output; disables all other pin functions.
RB4
0
O
DIG
LATB<4> data output.
PORTB<4> data input; weak pull-up when RBPU bit is cleared.
External interrupt 3 input.
1
I
TTL
KBI0
1
I
TTL
Interrupt-on-pin change.
SEG11
x
O
ANA
LCD segment 11 output; disables all other pin functions.
RB5
0
O
DIG
LATB<5> data output.
1
I
TTL
PORTB<5> data input; weak pull-up when RBPU bit is cleared.
1
I
TTL
Interrupt-on-pin change.
SEG29
x
O
ANA
LCD segment 29 output; disables all other pin functions.
RB6
0
O
DIG
LATB<6> data output.
1
I
TTL
PORTB<6> data input; weak pull-up when RBPU bit is cleared.
KBI2
1
I
TTL
Interrupt-on-pin change.
PGC
x
I
ST
Serial execution (ICSP™) clock input for ICSP and ICD operation.
RB7
0
O
DIG
LATB<7> data output.
PORTB<7> data input; weak pull-up when RBPU bit is cleared.
KBI1
RB6/KBI2/PGC
Description
1
I
TTL
KBI3
1
I
TTL
Interrupt-on-pin change.
PGD
x
O
DIG
Serial execution data output for ICSP and ICD operation.
x
I
ST
Serial execution data input for ICSP and ICD operation.
O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input,
TTL = TTL Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 113
PIC18F85J90 FAMILY
TABLE 9-6:
Name
PORTB
LATB
TRISB
SUMMARY OF REGISTERS ASSOCIATED WITH PORTB
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values on
page
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
55
LATB7
LATB6
LATB5
LATB4
LATB3
LATB2
LATB1
LATB0
54
TRISB7
TRISB6
TRISB5
TRISB4
TRISB3
TRISB2
TRISB1
TRISB0
54
INTCON
GIE/GIEH
PEIE/GIEL
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
INTCON2
RBPU
INTEDG0
INTEDG1
INTEDG2
INTEDG3
TMR0IP
INT3IP
RBIP
51
INTCON3
INT2IP
INT1IP
INT3IE
INT2IE
INT1IE
INT3IF
INT2IF
INT1IF
51
LCDSE1
SE15
SE14
SE13
SE12
SE11
SE10
SE09
SE08
53
LCDSE3
SE31
SE30
SE29
SE28
SE27
SE26
SE25
SE24
53
Legend:
Shaded cells are not used by PORTB.
DS39770B-page 114
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
9.4
PORTC, TRISC and
LATC Registers
PORTC is an 8-bit wide, bidirectional port. The
corresponding Data Direction and Output Latch registers
are TRISC and LATC. Only PORTC pins, RC2 through
RC7, are digital only pins and can tolerate input voltages
up to 5.5V.
PORTC is multiplexed with CCP, MSSP and EUSART
peripheral functions (Table 9-7). The pins have Schmitt
Trigger input buffers. The pins for CCP, SPI and
EUSART are also configurable for open-drain output
whenever these functions are active. Open-drain configuration is selected by setting the SPIOD, CCPxOD,
and U1OD control bits (TRISG<7:5> and LATG<6>,
respectively).
RC1 is normally configured as the default peripheral
pin for the CCP2 module. Assignment of CCP2 is
controlled by Configuration bit, CCP2MX (default state,
CCP2MX = 1).
The contents of the TRISC register are affected by
peripheral overrides. Reading TRISC always returns
the current contents, even though a peripheral device
may be overriding one or more of the pins.
RC<7:1> pins are multiplexed with LCD segment
drives, controlled by bits in the LCDSE1, LCDSE2,
LCDSE3 and LCDSE4 registers. I/O port functionality
is only available when the LCD segments are disabled.
EXAMPLE 9-3:
CLRF
PORTC
CLRF
LATC
MOVLW
0CFh
MOVWF
TRISC
When enabling peripheral functions, care should be
taken in defining TRIS bits for each PORTC pin. Some
peripherals override the TRIS bit to make a pin an output,
while other peripherals override the TRIS bit to make a
pin an input. The user should refer to the corresponding
peripheral section for the correct TRIS bit settings.
Note:
INITIALIZING PORTC
;
;
;
;
;
;
;
;
;
;
;
;
Initialize PORTC by
clearing output
data latches
Alternate method
to clear output
data latches
Value used to
initialize data
direction
Set RC<3:0> as inputs
RC<5:4> as outputs
RC<7:6> as inputs
These pins are configured as digital inputs
on any device Reset.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 115
PIC18F85J90 FAMILY
TABLE 9-7:
Pin Name
RC0/T1OSO/
T13CKI
RC1/T1OSI/
CCP2/SEG32
PORTC FUNCTIONS
Function
TRIS
Setting
I/O
I/O
Type
RC0
0
O
DIG
LATC<0> data output.
1
I
ST
PORTC<0> data input.
T1OSO
x
O
ANA
T13CKI
1
I
ST
RC1
0
O
DIG
LATC<1> data output.
1
I
ST
PORTC<1> data input.
T1OSI
I
ANA
Timer1 oscillator input.
0
O
DIG
CCP2 Compare/PWM output.
1
I
ST
SEG32
x
O
ANA
RC2
0
O
DIG
LATC<2> data output.
1
I
ST
PORTC<2> data input.
0
O
DIG
CCP1 Compare/PWM output; takes priority over port data.
1
I
ST
CCP1 Capture input.
SEG13
x
O
ANA
LCD segment 13 output; disables all other pin functions.
RC3
0
O
DIG
LATC<3> data output.
1
I
ST
PORTC<3> data input.
SCK
0
O
DIG
SPI clock output (MSSP module); takes priority over port data.
1
I
ST
SPI clock input (MSSP module).
0
O
DIG
I2C™ clock output (MSSP module); takes priority over port data.
1
I
I2C
I2C clock input (MSSP module); input type depends on module setting.
LCD segment 17 output; disables all other pin functions.
SCL
RC4/SDI/SDA/
SEG16
x
O
ANA
RC4
0
O
DIG
LATC<4> data output.
1
I
ST
PORTC<4> data input.
I
ST
SPI data input (MSSP module).
1
O
DIG
I2C data output (MSSP module); takes priority over port data.
1
I
I2C
I2C data input (MSSP module); input type depends on module setting.
SEG16
x
O
ANA
LCD segment 16 output; disables all other pin functions.
RC5
0
O
DIG
LATC<5> data output.
1
I
ST
PORTC<5> data input.
SDO
0
O
DIG
SPI data output (MSSP module).
SEG12
x
O
ANA
LCD segment 12 output; disables all other pin functions.
RC6
0
O
DIG
LATC<6> data output.
1
I
ST
PORTC<6> data input.
SDI
RC6/TX1/CK1/
SEG27
RC7/RX1/DT1/
SEG28
TX1
1
O
DIG
Synchronous serial data output (EUSART module); takes priority over port data.
CK1
1
O
DIG
Synchronous serial data input (EUSART module); user must configure as an input.
1
I
ST
SEG27
x
O
ANA
RC7
0
O
DIG
LATC<7> data output.
1
I
ST
PORTC<7> data input.
Asynchronous serial receive data input (EUSART module).
Note 1:
Synchronous serial clock input (EUSART module).
LCD segment 27 output; disables all other pin functions.
RX1
1
I
ST
DT1
1
O
DIG
Synchronous serial data output (EUSART module); takes priority over port data.
1
I
ST
Synchronous serial data input (EUSART module); user must configure as an input.
x
O
ANA
SEG28
Legend:
CCP2 Capture input.
LCD segment 32 output; disables all other pin functions.
SEG17
SDA
RC5/SDO/
SEG12
Timer1/Timer3 counter input.
x
CCP1
RC3/SCK/SCL/
SEG17
Timer1 oscillator output; enabled when Timer1 oscillator enabled. Disables digital I/O and LCD segment driver.
(1)
CCP2
RC2/CCP1/
SEG13
Description
LCD segment 28 output; disables all other pin functions.
O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, TTL = TTL Buffer Input,
I2C = I2C/SMBus Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
Default assignment for CCP2 when CCP2MX Configuration bit is set.
DS39770B-page 116
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 9-8:
SUMMARY OF REGISTERS ASSOCIATED WITH PORTC
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
55
LATC
LATC7
LATBC6
LATC5
LATCB4
LATC3
LATC2
LATC1
LATC0
54
TRISC
TRISC7
TRISC6
TRISC5
TRISC4
TRISC3
TRISC2
TRISC1
TRISC0
54
U1OD
—
Name
PORTC
LATG
U2OD
TRISG
SPIOD
CCP2OD CCP1OD
LATG4
LATG3
LATG2
LATG1
LATG0
54
TRISG4
TRISG3
TRISG2
TRISG1
TRISG0
54
LCDSE1
SE15
SE14
SE13
SE12
SE11
SE10
SE09
SE08
53
LCDSE2
SE23
SE22
SE21
SE20
SE19
SE18
SE17
SE16
53
LCDSE3
SE31
SE30
SE29
SE28
SE27
SE26
SE25
SE24
53
SE32
53
LCDSE4
(1)
SE39
(1)
SE38
(1)
SE37
SE36
(1)
SE35
(1)
SE34
(1)
SE33
(1)
Legend: Shaded cells are not used by PORTC.
Note 1: Unimplemented on 64-pin devices, read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 117
PIC18F85J90 FAMILY
9.5
PORTD, TRISD and
LATD Registers
PORTD is an 8-bit wide, bidirectional port. The
corresponding Data Direction and Output Latch registers
are TRISD and LATD. All pins on PORTD are digital only
and tolerate voltages up to 5.5V.
All pins on PORTD are implemented with Schmitt
Trigger input buffers. Each pin is individually
configurable as an input or output.
Note:
These pins are configured as digital inputs
on any device Reset.
Each of the PORTD pins has a weak internal pull-up. A
single control bit can turn off all the pull-ups. This is
performed by setting bit RDPU (PORTG<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on all device Resets.
DS39770B-page 118
All of the PORTD pins are multiplexed with LCD
segment drives, controlled by bits in the LCDSE0
register. I/O port functionality is only available when the
LCD segments are disabled.
EXAMPLE 9-4:
CLRF
PORTD
CLRF
LATD
MOVLW
0CFh
MOVWF
TRISD
Preliminary
INITIALIZING PORTD
;
;
;
;
;
;
;
;
;
;
;
;
Initialize PORTD by
clearing output
data latches
Alternate method
to clear output
data latches
Value used to
initialize data
direction
Set RD<3:0> as inputs
RD<5:4> as outputs
RD<7:6> as inputs
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 9-9:
Pin Name
RD0/SEG0
RD1/SEG1
RD2/SEG2
RD3/SEG3
RD4/SEG4
RD5/SEG5
RD6/SEG6
RD7/SEG7
PORTD FUNCTIONS
Function
TRIS
Setting
I/O
I/O
Type
RD0
0
O
DIG
LATD<0> data output.
1
I
ST
PORTD<0> data input.
SEG0
x
O
ANA
LCD segment 0 output; disables all other pin functions.
RD1
0
O
DIG
LATD<1> data output.
1
I
ST
SEG1
x
O
ANA
LCD segment 1 output; disables all other pin functions.
RD2
0
O
DIG
LATD<2> data output.
1
I
ST
SEG2
x
O
ANA
LCD segment 2 output; disables all other pin functions.
RD3
0
O
DIG
LATD<3> data output.
PORTD
PORTD<2> data input.
1
I
ST
x
O
ANA
LCD segment 3 output; disables all other pin functions.
PORTD<3> data input.
RD4
0
O
DIG
LATD<4> data output.
1
I
ST
PORTD<4> data input.
SEG4
x
O
ANA
LCD segment 4 output; disables all other pin functions.
RD5
0
O
DIG
LATD<5> data output.
1
I
ST
SEG5
x
O
ANA
LCD segment 5 output; disables all other pin functions.
RD6
0
O
DIG
LATD<6> data output.
1
I
ST
SEG6
x
O
ANA
LCD segment 6 output; disables all other pin functions.
RD7
0
O
DIG
LATD<7> data output.
1
I
ST
x
I
ANA
PORTD<5> data input.
PORTD<6> data input.
PORTD<7> data input.
LCD segment 7 output; disables all other pin functions.
O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input,
x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
TABLE 9-10:
Name
PORTD<1> data input.
SEG3
SEG7
Legend:
Description
SUMMARY OF REGISTERS ASSOCIATED WITH PORTD
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
RD7
RD6
RD5
RD4
RD3
RD2
RD1
RD0
55
LATD
LATD7
LATD6
LATD5
LATD4
LATD3
LATD2
LATD1
LATD0
54
TRISD
TRISD7
TRISD6
TRISD5
TRISD4
TRISD3
TRISD2
TRISD1
TRISD0
54
PORTG
RDPU
REPU
RJPU(1)
RG4
RG3
RG2
RG1
RG0
54
LCDSE0
SE7
SE6
SE5
SE4
SE3
SE2
SE1
SE0
53
Legend: Shaded cells are not used by PORTD.
Note 1: Unimplemented on 64-pin devices, read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 119
PIC18F85J90 FAMILY
9.6
PORTE, TRISE and
LATE Registers
PORTE is a 7-bit wide, bidirectional port. The
corresponding Data Direction and Output Latch registers
are TRISE and LATE. All pins on PORTE are digital only
and tolerate voltages up to 5.5V.
All pins on PORTE are implemented with Schmitt
Trigger input buffers. Each pin is individually
configurable as an input or output. The RE7 pin is also
configurable for open-drain output when CCP2 is active
on this pin. Open-drain configuration is selected by
setting the CCP2OD control bit (TRISG<6>)
Note:
These pins are configured as digital inputs
on any device Reset.
Each of the PORTE pins has a weak internal pull-up. A
single control bit can turn off all the pull-ups. This is
performed by setting bit, REPU (PORTG<6>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on any device Reset.
Pins RE6:RE3 are multiplexed with the LCD common
drives. I/O port functions are only available on those
PORTE pins depending on which commons are active.
The configuration is determined by the LMUX1:LMUX0
control bits (LCDCON<1:0>). The availability is
summarized in Table 9-11.
TABLE 9-11:
Pins RE1 and RE0 are multiplexed with the functions of
LCDBIAS2 and LCDBIAS1. When LCD bias generation is required (i.e., any application where the device
is connected to an external LCD), these pins cannot be
used as digital I/O.
Note:
The pin corresponding to RE2 of other
PIC18F parts has the function of
LCDBIAS3 in this device. It cannot be used
as digital I/O.
RE7 is multiplexed with LCD segment drive (SEG31)
controlled by the LCDSE3<7> bit. I/O port function is
only available when the segment is disabled.
RE7 can also be configured as the alternate peripheral
pin for the CCP2 module. This is done by clearing the
CCP2MX Configuration bit.
EXAMPLE 9-5:
CLRF
PORTE
CLRF
LATE
MOVLW
03h
MOVWF
TRISE
INITIALIZING PORTE
;
;
;
;
;
;
;
;
;
;
;
Initialize PORTE by
clearing output
data latches
Alternate method
to clear output
data latches
Value used to
initialize data
direction
Set RE<1:0> as inputs
RE<7:2> as outputs
PORTE PINS AVAILABLE IN
DIFFERENT LCD DRIVE
CONFIGURATIONS
LCDCON
<1:0>
Active LCD
Commons
PORTE Available
for I/O
00
COM0
RE6, RE5, RE4
01
COM0, COM1
RE6, RE5
10
COM0, COM1
and COM2
RE6
11
All (COM0
through COM3)
None
DS39770B-page 120
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 9-12:
PORTE FUNCTIONS
Pin Name
Function
TRIS
Setting
I/O
I/O
Type
RE0/LCDBIAS1
RE0
0
O
DIG
LATE<0> data output.
1
I
ST
PORTE<0> data input.
LCDBIAS1
—
I
ANA
LCD module bias voltage input.
RE1
0
O
DIG
LATE<1> data output.
1
I
ST
PORTE<1> data input.
RE1/LCDBIAS2
RE3/COM0
RE4/COM1
RE5/COM2
RE6/COM3
RE7/CCP2/
SEG31
LCDBIAS2
—
I
ANA
LCD module bias voltage input.
RE3
0
O
DIG
LATE<3> data output.
1
I
ST
COM0
x
O
ANA
LCD Common 0 output; disables all other outputs.
RE4
0
O
DIG
LATE<4> data output.
1
I
ST
COM1
x
O
ANA
LCD Common 1 output; disables all other outputs.
RE5
0
O
DIG
LATE<5> data output.
I
ST
x
O
ANA
LCD Common 2 output; disables all other outputs.
PORTE
PORTE<5> data input.
RE6
0
O
DIG
LATE<6> data output.
1
I
ST
PORTE<6> data input.
COM3
x
O
ANA
LCD Common 3 output; disables all other outputs.
RE7
0
O
DIG
LATE<7> data output.
1
I
ST
PORTE<7> data input.
0
O
DIG
CCP2 Compare/PWM output; takes priority over port data.
1
I
ST
x
O
ANA
CCP2 Capture input.
Segment 31 analog output for LCD; disables digital output.
O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input,
x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
Alternate assignment for CCP2 when CCP2MX Configuration bit is cleared.
TABLE 9-13:
Name
PORTE<4> data input.
1
SEG31
Note 1:
PORTE<3> data input.
COM2
CCP2(1)
Legend:
Description
SUMMARY OF REGISTERS ASSOCIATED WITH PORTE
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
RE7
RE6
RE5
RE4
RE3
—
RE1
RE0
55
LATE
LATE7
LATE6
LATE5
LATE4
LATE3
—
LATE1
LATE0
54
TRISE
TRISE7
TRISE6
TRISE5
TRISE4
TRISE3
—
TRISE1
TRISE0
54
(1)
PORTG
RDPU
REPU
TRISG
SPIOD
CCP2OD
CCP1OD
RJPU
RG4
RG3
RG2
RG1
RG0
54
TRISG4
TRISG3
TRISG2
TRISG1
TRISG0
54
LCDCON
LCDEN
SLPEN
WERR
—
LCDSE3
SE31
SE30
SE29
SE28
CS1
CS0
LMUX1
LMUX0
53
SE27
SE26
SE25
SE24
53
Legend: Shaded cells are not used by PORTE.
Note 1: Unimplemented on 64-pin devices, read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 121
PIC18F85J90 FAMILY
9.7
PORTF, LATF and TRISF Registers
PORTF is a 7-bit wide, bidirectional port. The
corresponding Data Direction and Output Latch registers
are TRISF and LATF. All pins on PORTF are
implemented with Schmitt Trigger input buffers. Each pin
is individually configurable as an input or output.
PORTF is also multiplexed with LCD segment drives
controlled by bits in the LCDSE2 and LCDSE3
registers. I/O port functions are only available when the
segments are disabled.
EXAMPLE 9-6:
CLRF
PORTF is multiplexed with analog peripheral functions,
as well as LCD segments. Pins RF1 through RF6 may
be used as comparator inputs or outputs by setting the
appropriate bits in the CMCON register. To use
RF6:RF3 as digital inputs, it is also necessary to turn off
the comparators.
CLRF
Note 1: On device Resets, pins RF6:RF1 are
configured as analog inputs and are read
as ‘0’.
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
2: To configure PORTF as digital I/O, turn off
comparators and set ADCON1 value.
MOVWF
DS39770B-page 122
Preliminary
PORTF
;
;
;
LATF
;
;
;
07h
;
CMCON
;
0Fh
;
ADCON1 ;
0CEh
;
;
;
TRISF
;
;
;
INITIALIZING PORTF
Initialize PORTF by
clearing output
data latches
Alternate method
to clear output
data latches
Turn off comparators
Set PORTF as digital I/O
Value used to
initialize data
direction
Set RF3:RF1 as inputs
RF5:RF4 as outputs
RF7:RF6 as inputs
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 9-14:
PORTF FUNCTIONS
Pin Name
Function
TRIS
Setting
I/O
I/O
Type
RF1/AN6/C2OUT/
SEG19
RF1
0
O
DIG
1
I
ST
1
I
ANA
AN6
RF2/AN7/C1OUT/
SEG20
RF3/AN8/SEG21
RF4/AN9/SEG22
RF5/AN10/CVREF/
SEG23
RF6/AN11/SEG24
RF7/AN5/SS/
SEG25
Legend:
Description
LATF<1> data output; not affected by analog input.
PORTF<1> data input; disabled when analog input enabled.
A/D input channel 6. Default configuration on POR.
C2OUT
0
O
DIG
Comparator 2 output; takes priority over port data.
SEG19
x
O
ANA
LCD segment 19 output; disables all other pin functions.
LATF<2> data output; not affected by analog input.
RF2
0
O
DIG
1
I
ST
AN7
1
I
ANA
A/D input channel 7. Default configuration on POR.
C1OUT
0
O
DIG
Comparator 1 output; takes priority over port data.
SEG20
x
O
ANA
LCD segment 20 output; disables all other pin functions.
RF3
0
O
DIG
LATF<3> data output; not affected by analog input.
1
I
ST
PORTF<3> data input; disabled when analog input enabled.
AN8
1
I
ANA
A/D input channel 8 and Comparator C2+ input. Default input
configuration on POR; not affected by analog output.
SEG21
x
O
ANA
LCD segment 21 output; disables all other pin functions.
RF4
0
O
DIG
LATF<4> data output; not affected by analog input.
PORTF<2> data input; disabled when analog input enabled.
1
I
ST
PORTF<4> data input; disabled when analog input enabled.
AN9
1
I
ANA
A/D input channel 9 and Comparator C2- input. Default input
configuration on POR; does not affect digital output.
SEG22
x
O
ANA
LCD segment 22 output; disables all other pin functions.
RF5
0
O
DIG
LATF<5> data output; not affected by analog input. Disabled when
CVREF output enabled.
1
I
ST
PORTF<5> data input; disabled when analog input enabled. Disabled
when CVREF output enabled.
AN10
1
I
ANA
A/D input channel 10 and Comparator C1+ input. Default input
configuration on POR.
CVREF
x
O
ANA
Comparator voltage reference output. Enabling this feature disables
digital I/O.
SEG23
x
O
ANA
LCD segment 23 output; disables all other pin functions.
RF6
0
O
DIG
LATF<6> data output; not affected by analog input.
1
I
ST
PORTF<6> data input; disabled when analog input enabled.
AN11
1
I
ANA
A/D input channel 11 and Comparator C1- input. Default input
configuration on POR; does not affect digital output.
SEG24
x
O
ANA
LCD segment 24 output; disables all other pin functions.
RF7
0
O
DIG
LATF<7> data output; not affected by analog input.
1
I
ST
AN5
1
I
ANA
SS
1
I
TTL
Slave select input for MSSP module.
SEG25
x
O
ANA
LCD segment 25 output; disables all other pin functions.
PORTF<7> data input; disabled when analog input enabled.
A/D input channel 5. Default configuration on POR.
O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input,
TTL = TTL Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 123
PIC18F85J90 FAMILY
TABLE 9-15:
Name
PORTF
SUMMARY OF REGISTERS ASSOCIATED WITH PORTF
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
RF7
RF6
RF5
RF4
RF3
RF2
RF1
—
54
54
LATF
LATF7
LATF6
LATF5
LATF4
LATF3
LATF2
LATF1
—
TRISF
TRISF7
TRISF6
TRISF5
TRISF4
TRISF3
TRISF2
TRISF1
—
54
ADCON1
—
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
53
CMCON
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
53
53
CVRCON
CVREN
CVROE
CVRR
CVRSS
CVR3
CVR2
CVR1
CVR0
LCDSE2
SE23
SE22
SE21
SE20
SE19
SE18
SE17
SE16
53
LCDSE3
SE31
SE30
SE29
SE28
SE27
SE26
SE25
SE24
53
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PORTF.
DS39770B-page 124
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
9.8
PORTG, TRISG and
LATG Registers
PORTG is a 5-bit wide, bidirectional port. The
corresponding Data Direction and Output Latch registers
are TRISG and LATG. All pins on PORTG are digital only
and tolerate voltages up to 5.5V.
PORTG is multiplexed with both AUSART and LCD
functions (Table 9-16). When operating as I/O, all
PORTG pins have Schmitt Trigger input buffers. The
RG1 pin is also configurable for open-drain output
when the AUSART is active. Open-drain configuration
is selected by setting the U2OD control bit (LATG<7>).
RG4 is multiplexed with LCD segment drives controlled
by bits in the LCDSE2 register. The I/O port function is
only available when the segments are disabled.
Although the port itself is only five bits wide, the
PORTG<7:5> bits are still implemented to control the
weak pull-ups on the I/O ports associated with PORTD,
PORTE and PORTJ. Setting these bits enables the
respective port pull-ups.
Most of the corresponding TRISG and LATG bits are
implemented as open-drain control bits for CCP1,
CCP2 and SPI (TRISG<7:5>), and the USARTs
(LATG<7:6>). Setting these bits configures the output
pin for the corresponding peripheral for open-drain
operation. LATG<5> is not implemented.
EXAMPLE 9-7:
CLRF
PORTG
RG3 and RG2 are multiplexed with VLCAP pins for the
LCD charge pump, and RG0 is multiplexed with
LCDBIAS0 bias voltage input. When these pins are
used for LCD bias generation, the I/O and other
functions are unavailable.
CLRF
LATG
MOVLW
04h
When enabling peripheral functions, care should be
taken in defining TRIS bits for each PORTG pin. Some
peripherals override the TRIS bit to make a pin an
output, while other peripherals override the TRIS bit to
make a pin an input. The user should refer to the
corresponding peripheral section for the correct TRIS bit
settings. The pin override value is not loaded into the
TRIS register. This allows read-modify-write of the TRIS
register without concern due to peripheral overrides.
MOVWF
TRISG
© 2007 Microchip Technology Inc.
Preliminary
INITIALIZING PORTG
;
;
;
;
;
;
;
;
;
;
;
;
Initialize PORTG by
clearing output
data latches
Alternate method
to clear output
data latches
Value used to
initialize data
direction
Set RG1:RG0 as outputs
RG2 as input
RG4:RG3 as inputs
DS39770B-page 125
PIC18F85J90 FAMILY
TABLE 9-16:
PORTG FUNCTIONS
Pin Name
Function
TRIS
Setting
I/O
I/O
Type
RG0/LCDBIAS0
RG0
0
O
DIG
LATG<0> data output.
1
I
ST
LCDBIAS0
x
I
ANA
LCD module bias voltage input.
RG1
0
O
DIG
LATG<1> data output.
1
I
ST
PORTG<1> data input.
TX2
1
O
DIG
Synchronous serial data output (AUSART module); takes priority over
port data.
CK2
1
O
DIG
Synchronous serial data input (AUSART module); user must configure
as an input.
1
I
ST
Synchronous serial clock input (AUSART module).
RG2
0
O
DIG
LATG<2> data output.
RG1/TX2/CK2
RG2/RX2/DT2/V
LCAP1
RG3/VLCAP2
RG4/SEG26
PORTG<0> data input.
1
I
ST
PORTG<2> data input.
RX2
1
I
ST
Asynchronous serial receive data input (AUSART module).
DT2
1
O
DIG
Synchronous serial data output (AUSART module); takes priority over
port data.
1
I
ST
Synchronous serial data input (AUSART module); user must configure
as an input.
VLCAP1
x
I
ANA
LCD charge pump capacitor input.
RG3
0
O
DIG
LATG<3> data output.
1
I
ST
VLCAP2
x
I
ANA
LCD charge pump capacitor input.
RG4
0
O
DIG
LATG<4> data output.
1
I
ST
x
O
ANA
SEG26
Legend:
Description
PORTG<3> data input.
PORTG<4> data input.
LCD segment 26 output; disables all other pin functions.
O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input,
x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
TABLE 9-17:
SUMMARY OF REGISTERS ASSOCIATED WITH PORTG
Name
Bit 6
Bit 5
PORTG
RDPU
REPU
RJPU(1)
RG4
RG3
RG2
RG1
RG0
54
LATG
U2OD
U1OD
—
LATG4
LATG3
LATG2
LATG1
LATG0
54
TRISG
SPIOD
CCP2OD CCP1OD TRISG4
TRISG3
TRISG2
TRISG1
TRISG0
54
SE27
SE26
SE25
SE24
53
LCDSE3
SE31
SE30
SE29
Bit 4
SE28
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values on
page
Bit 7
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PORTG.
Note 1: Unimplemented on 64-pin devices, read as ‘0’.
DS39770B-page 126
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
9.9
Note:
EXAMPLE 9-8:
PORTH, LATH and
TRISH Registers
PORTH is available only on 80-pin
devices.
PORTH is an 8-bit wide, bidirectional I/O port. The
corresponding Data Direction and Output Latch registers
are TRISH and LATH. All pins are digital only and
tolerate voltages up to 5.5V.
All pins on PORTH are implemented with Schmitt
Trigger input buffers. Each pin is individually
configurable as an input or output.
CLRF
PORTH
CLRF
LATH
MOVLW
MOVWF
MOVLW
0Fh
ADCON1
0CFh
MOVWF
TRISH
All PORTH pins are multiplexed with LCD segment
drives controlled by the LCDSE5 register. I/O port
functions are only available when the segments are
disabled.
© 2007 Microchip Technology Inc.
Preliminary
INITIALIZING PORTH
;
;
;
;
;
;
;
;
;
;
;
;
;
;
Initialize PORTH by
clearing output
data latches
Alternate method
to clear output
data latches
Configure PORTH as
digital I/O
Value used to
initialize data
direction
Set RH3:RH0 as inputs
RH5:RH4 as outputs
RH7:RH6 as inputs
DS39770B-page 127
PIC18F85J90 FAMILY
TABLE 9-18:
Pin Name
PORTH FUNCTIONS
Function
TRIS
Setting
I/O
I/O
Type
RH0
0
O
DIG
RH0/SEG47
RH1/SEG46
RH2/SEG45
RH3/SEG44
RH4/SEG40
RH5/SEG41
RH6/SEG42
RH7/SEG43
1
I
ST
x
O
ANA
LCD segment 47 output; disables all other pin functions.
PORTH
PORTH<0> data input.
RH1
0
O
DIG
LATH<1> data output.
1
I
ST
PORTH<1> data input.
SEG46
x
O
ANA
LCD segment 46 output; disables all other pin functions.
RH2
0
O
DIG
LATH<2> data output.
1
I
ST
SEG45
x
O
ANA
LCD segment 45 output; disables all other pin functions.
RH3
0
O
DIG
LATH<3> data output.
1
I
ST
SEG44
x
O
ANA
LCD segment 44 output; disables all other pin functions.
RH4
0
O
DIG
LATH<4> data output.
PORTH<2> data input.
PORTH<3> data input.
1
I
ST
SEG40
x
O
ANA
LCD segment 40 output; disables all other pin functions.
PORTH<4> data input.
RH5
0
O
DIG
LATH<5> data output.
1
I
ST
PORTH<5> data input.
SEG41
x
O
ANA
LCD segment 41 output; disables all other pin functions.
RH6
0
O
DIG
LATH<6> data output.
1
I
ST
SEG42
x
O
ANA
LCD segment 42 output; disables all other pin functions.
RH7
0
O
DIG
LATH<7> data output.
1
I
ST
x
O
ANA
PORTH<6> data input.
PORTH<7> data input.
LCD segment 43 output; disables all other pin functions.
O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input,
x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
TABLE 9-19:
Name
LATH<0> data output.
SEG47
SEG43
Legend:
Description
SUMMARY OF REGISTERS ASSOCIATED WITH PORTH
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
RH7
RH6
RH5
RH4
RH3
RH2
RH1
RH0
54
LATH
LATH7
LATH6
LATH5
LATH4
LATH3
LATH2
LATH1
LATH0
54
TRISH
TRISH7
TRISH6
TRISH5
TRISH4
TRISH3
TRISH2
TRISH1
TRISH0
54
SE47
SE46
SE45
SE44
SE43
SE42
SE41
SE40
53
LCDSE5
DS39770B-page 128
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
9.10
Note:
PORTJ, TRISJ and
LATJ Registers
PORTJ is available only on 80-pin devices.
PORTJ is an 8-bit wide, bidirectional port. The
corresponding Data Direction and Output Latch registers
are TRISJ and LATJ. All pins on PORTJ are digital only
and tolerate voltages up to 5.5V.
All pins on PORTJ are implemented with Schmitt
Trigger input buffers. Each pin is individually
configurable as an input or output.
Note:
These pins are configured as digital inputs
on any device Reset.
All PORTJ pins except RJ0 are multiplexed with LCD
segment drives controlled by the LCDSE4 register. I/O
port functions are only available on these pins when the
segments are disabled.
© 2007 Microchip Technology Inc.
Each of the PORTJ pins has a weak internal pull-up.
The pull-ups are provided to keep the inputs at a known
state for the external memory interface while powering
up. A single control bit can turn off all the pull-ups. This
is performed by clearing bit RJPU (PORTG<5>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on any device Reset.
EXAMPLE 9-9:
CLRF
PORTJ
CLRF
LATJ
MOVLW
0CFh
MOVWF
TRISJ
Preliminary
INITIALIZING PORTJ
;
;
;
;
;
;
;
;
;
;
Initialize PORTJ by
clearing output latches
Alternate method
to clear output latches
Value used to
initialize data
direction
Set RJ3:RJ0 as inputs
RJ5:RJ4 as output
RJ7:RJ6 as inputs
DS39770B-page 129
PIC18F85J90 FAMILY
TABLE 9-20:
PORTJ FUNCTIONS
Function
TRIS
Setting
I/O
I/O
Type
RJ0
RJ0
0
O
DIG
LATJ<0> data output.
RJ1/SEG33
RJ1
Pin Name
RJ2/SEG34
RJ3/SEG35
RJ4/SEG39
RJ5/SEG38
RJ6/SEG37
RJ7/SEG36
1
I
ST
PORTJ<0> data input.
0
O
DIG
LATJ<1> data output.
1
I
ST
SEG33
x
O
ANA
LCD segment 33 output; disables all other pin functions.
RJ2
0
O
DIG
LATJ<2> data output.
1
I
ST
SEG34
x
O
ANA
LCD segment 34 output; disables all other pin functions.
RJ3
0
O
DIG
LATJ<3> data output.
PORTJ
PORTJ<2> data input.
1
I
ST
x
O
ANA
LCD segment 35 output; disables all other pin functions.
PORTJ<3> data input.
RJ4
0
O
DIG
LATJ<4> data output.
1
I
ST
PORTJ<4> data input.
SEG39
x
O
ANA
LCD segment 39 output; disables all other pin functions.
RJ5
0
O
DIG
LATJ<5> data output.
1
I
ST
SEG38
x
O
ANA
LCD segment 38 output; disables all other pin functions.
RJ6
0
O
DIG
LATJ<6> data output.
1
I
ST
SEG37
x
O
ANA
LCD segment 37 output; disables all other pin functions.
RJ7
0
O
DIG
LATJ<7> data output.
PORTJ<5> data input.
PORTJ<6> data input.
1
I
ST
x
O
ANA
PORTJ<7> data input.
LCD segment 36 output; disables all other pin functions.
O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input,
x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
TABLE 9-21:
Name
PORTJ<1> data input.
SEG35
SEG36
Legend:
Description
SUMMARY OF REGISTERS ASSOCIATED WITH PORTJ
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
RJ7
RJ6
RJ5
RJ4
RJ3
RJ2
RJ1
RJ0
54
LATJ
LATJ7
LATJ6
LATJ5
LATJ4
LATJ3
LATJ2
LATJ1
LATJ0
54
TRISJ
TRISJ7
TRISJ6
TRISJ5
TRISJ4
TRISJ3
TRISJ2
TRISJ1
TRISJ0
54
RG4
RG3
RG2
RG1
RG0
54
SE36
SE35
SE34
SE33
SE32
53
PORTG
RDPU
REPU
RJPU(1)
LCDSE4
SE39
SE38
SE37
Legend: Shaded cells are not used by PORTJ.
Note 1: Unimplemented on 64-pin devices, read as ‘0’.
DS39770B-page 130
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
10.0
TIMER0 MODULE
The Timer0 module incorporates the following features:
• Software selectable operation as a timer or
counter in both 8-bit or 16-bit modes
• Readable and writable registers
• Dedicated 8-bit, software programmable
prescaler
• Selectable clock source (internal or external)
• Edge select for external clock
• Interrupt-on-overflow
REGISTER 10-1:
The T0CON register (Register 10-1) controls all
aspects of the module’s operation, including the
prescale selection; it is both readable and writable.
A simplified block diagram of the Timer0 module in 8-bit
mode is shown in Figure 10-1. Figure 10-2 shows a
simplified block diagram of the Timer0 module in 16-bit
mode.
T0CON: TIMER0 CONTROL REGISTER
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
TMR0ON
T08BIT
T0CS
T0SE
PSA
T0PS2
T0PS1
T0PS0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
TMR0ON: Timer0 On/Off Control bit
1 = Enables Timer0
0 = Stops Timer0
bit 6
T08BIT: Timer0 8-Bit/16-Bit Control bit
1 = Timer0 is configured as an 8-bit timer/counter
0 = Timer0 is configured as a 16-bit timer/counter
bit 5
T0CS: Timer0 Clock Source Select bit
1 = Transition on T0CKI pin
0 = Internal instruction cycle clock (CLKO)
bit 4
T0SE: Timer0 Source Edge Select bit
1 = Increment on high-to-low transition on T0CKI pin
0 = Increment on low-to-high transition on T0CKI pin
bit 3
PSA: Timer0 Prescaler Assignment bit
1 = TImer0 prescaler is not assigned. Timer0 clock input bypasses prescaler.
0 = Timer0 prescaler is assigned. Timer0 clock input comes from prescaler output.
bit 2-0
T0PS2:T0PS0: Timer0 Prescaler Select bits
111 = 1:256 Prescale value
110 = 1:128 Prescale value
101 = 1:64 Prescale value
100 = 1:32 Prescale value
011 = 1:16 Prescale value
010 = 1:8 Prescale value
001 = 1:4 Prescale value
000 = 1:2 Prescale value
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 131
PIC18F85J90 FAMILY
10.1
Timer0 Operation
internal phase clock (TOSC). There is a delay between
synchronization and the onset of incrementing the
timer/counter.
Timer0 can operate as either a timer or a counter. The
mode is selected with the T0CS bit (T0CON<5>). In
Timer mode (T0CS = 0), the module increments on
every clock by default unless a different prescaler value
is selected (see Section 10.3 “Prescaler”). If the
TMR0 register is written to, the increment is inhibited
for the following two instruction cycles. The user can
work around this by writing an adjusted value to the
TMR0 register.
10.2
TMR0H is not the actual high byte of Timer0 in 16-bit
mode. It is actually a buffered version of the real high
byte of Timer0, which is not directly readable nor writable (refer to Figure 10-2). TMR0H is updated with the
contents of the high byte of Timer0 during a read of
TMR0L. This provides the ability to read all 16 bits of
Timer0 without having to verify that the read of the high
and low byte were valid, due to a rollover between
successive reads of the high and low byte.
The Counter mode is selected by setting the T0CS bit
(= 1). In this mode, Timer0 increments either on every
rising or falling edge of pin RA4/T0CKI. The incrementing edge is determined by the Timer0 Source Edge
Select bit, T0SE (T0CON<4>); clearing this bit selects
the rising edge. Restrictions on the external clock input
are discussed below.
Similarly, a write to the high byte of Timer0 must also
take place through the TMR0H Buffer register. The high
byte is updated with the contents of TMR0H when a
write occurs to TMR0L. This allows all 16 bits of Timer0
to be updated at once.
An external clock source can be used to drive Timer0,
however, it must meet certain requirements to ensure
that the external clock can be synchronized with the
FIGURE 10-1:
Timer0 Reads and Writes in
16-Bit Mode
TIMER0 BLOCK DIAGRAM (8-BIT MODE)
FOSC/4
0
1
1
Programmable
Prescaler
T0CKI pin
T0SE
T0CS
0
Sync with
Internal
Clocks
Set
TMR0IF
on Overflow
TMR0L
(2 TCY Delay)
8
3
T0PS2:T0PS0
8
PSA
Note:
Internal Data Bus
Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI max. prescale.
FIGURE 10-2:
TIMER0 BLOCK DIAGRAM (16-BIT MODE)
FOSC/4
0
1
1
Programmable
Prescaler
T0CKI pin
T0SE
T0CS
0
Sync with
Internal
Clocks
TMR0
High Byte
TMR0L
8
Set
TMR0IF
on Overflow
(2 TCY Delay)
3
Read TMR0L
T0PS2:T0PS0
Write TMR0L
PSA
8
8
TMR0H
8
8
Internal Data Bus
Note:
Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI max. prescale.
DS39770B-page 132
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
10.3
10.3.1
Prescaler
An 8-bit counter is available as a prescaler for the Timer0
module. The prescaler is not directly readable or writable.
Its value is set by the PSA and T0PS2:T0PS0 bits
(T0CON<3:0>) which determine the prescaler
assignment and prescale ratio.
Clearing the PSA bit assigns the prescaler to the
Timer0 module. When it is assigned, prescale values
from 1:2 through 1:256, in power-of-2 increments, are
selectable.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g., CLRF TMR0, MOVWF
TMR0, BSF TMR0, etc.) clear the prescaler count.
Note:
Writing to TMR0 when the prescaler is
assigned to Timer0 will clear the prescaler
count but will not change the prescaler
assignment.
TABLE 10-1:
Name
SWITCHING PRESCALER
ASSIGNMENT
The prescaler assignment is fully under software
control and can be changed “on-the-fly” during program
execution.
10.4
Timer0 Interrupt
The TMR0 interrupt is generated when the TMR0
register overflows from FFh to 00h in 8-bit mode, or
from FFFFh to 0000h in 16-bit mode. This overflow sets
the TMR0IF flag bit. The interrupt can be masked by
clearing the TMR0IE bit (INTCON<5>). Before
re-enabling the interrupt, the TMR0IF bit must be
cleared in software by the Interrupt Service Routine.
Since Timer0 is shut down in Sleep mode, the TMR0
interrupt cannot awaken the processor from Sleep.
REGISTERS ASSOCIATED WITH TIMER0
Bit 7
Bit 6
Bit 5
TMR0L
Timer0 Register Low Byte
TMR0H
Timer0 Register High Byte
INTCON
GIE/GIEH PEIE/GIEL TMR0IE
T0CON
TMR0ON
TRISA
TRISA7(1) TRISA6(1)
T08BIT
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
52
52
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
T0CS
T0SE
PSA
T0PS2
T0PS1
T0PS0
52
TRISA5
TRISA4
TRISA3
TRISA2
TRISA1
TRISA0
54
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by Timer0.
Note 1: RA6/RA7 and their associated latch and direction bits are configured as port pins only when the internal
oscillator is selected as the default clock source (FOSC2 Configuration bit = 0); otherwise, they are
disabled and these bits read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 133
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 134
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
11.0
TIMER1 MODULE
The Timer1 timer/counter module incorporates these
features:
• Software selectable operation as a 16-bit timer or
counter
• Readable and writable 8-bit registers (TMR1H
and TMR1L)
• Selectable clock source (internal or external) with
device clock or Timer1 oscillator internal options
• Interrupt on overflow
• Reset on CCP Special Event Trigger
• Device clock status flag (T1RUN)
REGISTER 11-1:
A simplified block diagram of the Timer1 module is
shown in Figure 11-1. A block diagram of the module’s
operation in Read/Write mode is shown in Figure 11-2.
The module incorporates its own low-power oscillator
to provide an additional clocking option. The Timer1
oscillator can also be used as a low-power clock source
for the microcontroller in power-managed operation.
Timer1 can also be used to provide Real-Time Clock
(RTC) functionality to applications with only a minimal
addition of external components and code overhead.
Timer1 is controlled through the T1CON Control
register (Register 11-1). It also contains the Timer1
Oscillator Enable bit (T1OSCEN). Timer1 can be
enabled or disabled by setting or clearing control bit,
TMR1ON (T1CON<0>).
T1CON: TIMER1 CONTROL REGISTER
R/W-0
R-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RD16
T1RUN
T1CKPS1
T1CKPS0
T1OSCEN
T1SYNC
TMR1CS
TMR1ON
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
RD16: 16-Bit Read/Write Mode Enable bit
1 = Enables register read/write of TImer1 in one 16-bit operation
0 = Enables register read/write of Timer1 in two 8-bit operations
bit 6
T1RUN: Timer1 System Clock Status bit
1 = Device clock is derived from Timer1 oscillator
0 = Device clock is derived from another source
bit 5-4
T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
bit 3
T1OSCEN: Timer1 Oscillator Enable bit
1 = Timer1 oscillator is enabled
0 = Timer1 oscillator is shut off
The oscillator inverter and feedback resistor are turned off to eliminate power drain.
bit 2
T1SYNC: Timer1 External Clock Input Synchronization Select bit
When TMR1CS = 1:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
When TMR1CS = 0:
This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.
bit 1
TMR1CS: Timer1 Clock Source Select bit
1 = External clock from pin RC0/T1OSO/T13CKI (on the rising edge)
0 = Internal clock (FOSC/4)
bit 0
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 135
PIC18F85J90 FAMILY
11.1
Timer1 Operation
cycle (FOSC/4). When the bit is set, Timer1 increments
on every rising edge of the Timer1 external clock input
or the Timer1 oscillator, if enabled.
Timer1 can operate in one of these modes:
• Timer
• Synchronous Counter
• Asynchronous Counter
When Timer1 is enabled, the RC1/T1OSI and
RC0/T1OSO/T13CKI pins become inputs. This means
the values of TRISC<1:0> are ignored and the pins are
read as ‘0’.
The operating mode is determined by the clock select
bit, TMR1CS (T1CON<1>). When TMR1CS is cleared
(= 0), Timer1 increments on every internal instruction
FIGURE 11-1:
TIMER1 BLOCK DIAGRAM (8-BIT MODE)
Timer1 Oscillator
Timer1 Clock Input
1
On/Off
1
T1OSO/T13CKI
T1OSI
Synchronize
Prescaler
1, 2, 4, 8
FOSC/4
Internal
Clock
0
Detect
0
2
T1OSCEN(1)
Sleep Input
Timer1
On/Off
TMR1CS
T1CKPS1:T1CKPS0
T1SYNC
TMR1ON
Clear TMR1
(CCP Special Event Trigger)
Set
TMR1IF
on Overflow
TMR1
High Byte
TMR1L
Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain.
FIGURE 11-2:
TIMER1 BLOCK DIAGRAM (16-BIT READ/WRITE MODE)
Timer1 Oscillator
Timer1 Clock Input
1
T1OSO/T13CKI
1
FOSC/4
Internal
Clock
Synchronize
Prescaler
1, 2, 4, 8
0
Detect
0
T1OSI
2
Sleep Input
TMR1CS
T1OSCEN(1)
T1CKPS1:T1CKPS0
T1SYNC
TMR1ON
Clear TMR1
(CCP Special Event Trigger)
Timer1
On/Off
TMR1
High Byte
TMR1L
8
Set
TMR1IF
on Overflow
Read TMR1L
Write TMR1L
8
8
TMR1H
8
8
Internal Data Bus
Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain.
DS39770B-page 136
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
11.2
TABLE 11-1:
Timer1 16-Bit Read/Write Mode
Timer1 can be configured for 16-bit reads and writes
(see Figure 11-2). When the RD16 control bit
(T1CON<7>) is set, the address for TMR1H is mapped
to a buffer register for the high byte of Timer1. A read
from TMR1L will load the contents of the high byte of
Timer1 into the Timer1 High Byte Buffer register. This
provides the user with the ability to accurately read all
16 bits of Timer1 without having to determine whether
a read of the high byte, followed by a read of the low
byte, has become invalid due to a rollover between
reads.
Oscillator
Type
Freq.
C1
C2
LP
32.768 kHz
27 pF(1)
27 pF(1)
Note 1: Microchip suggests these values as a
starting point in validating the oscillator
circuit.
2: Higher capacitance increases the stability
of the oscillator but also increases the
start-up time.
A write to the high byte of Timer1 must also take place
through the TMR1H Buffer register. The Timer1 high
byte is updated with the contents of TMR1H when a
write occurs to TMR1L. This allows a user to write all
16 bits to both the high and low bytes of Timer1 at once.
The high byte of Timer1 is not directly readable or
writable in this mode. All reads and writes must take
place through the Timer1 High Byte Buffer register.
Writes to TMR1H do not clear the Timer1 prescaler.
The prescaler is only cleared on writes to TMR1L.
11.3
Timer1 Oscillator
An on-chip crystal oscillator circuit is incorporated
between pins T1OSI (input) and T1OSO (amplifier
output). It is enabled by setting the Timer1 Oscillator
Enable bit, T1OSCEN (T1CON<3>). The oscillator is a
low-power circuit rated for 32 kHz crystals. It will
continue to run during all power-managed modes. The
circuit for a typical LP oscillator is shown in Figure 11-3.
Table 11-1 shows the capacitor selection for the Timer1
oscillator.
The user must provide a software time delay to ensure
proper start-up of the Timer1 oscillator.
FIGURE 11-3:
EXTERNAL
COMPONENTS FOR THE
TIMER1 LP OSCILLATOR
C1
27 pF
PIC18F85J90
CAPACITOR SELECTION FOR
THE TIMER1
OSCILLATOR(2,3,4)
3: Since each resonator/crystal has its own
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate
values
of
external
components.
4: Capacitor values are for design guidance
only.
11.3.1
USING TIMER1 AS A
CLOCK SOURCE
The Timer1 oscillator is also available as a clock source
in power-managed modes. By setting the System
Clock Select bits, SCS1:SCS0 (OSCCON<1:0>), to
‘01’, the device switches to SEC_RUN mode; both the
CPU and peripherals are clocked from the Timer1
oscillator. If the IDLEN bit (OSCCON<7>) is cleared
and a SLEEP instruction is executed, the device enters
SEC_IDLE mode. Additional details are available in
Section 3.0 “Power-Managed Modes”.
Whenever the Timer1 oscillator is providing the clock
source, the Timer1 system clock status flag, T1RUN
(T1CON<6>), is set. This can be used to determine the
controller’s current clocking mode. It can also indicate
the clock source being currently used by the Fail-Safe
Clock Monitor. If the Clock Monitor is enabled and the
Timer1 oscillator fails while providing the clock, polling
the T1RUN bit will indicate whether the clock is being
provided by the Timer1 oscillator or another source.
T1OSI
XTAL
32.768 kHz
T1OSO
C2
27 pF
Note:
See the Notes with Table 11-1 for additional
information about capacitor selection.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 137
PIC18F85J90 FAMILY
11.3.2
TIMER1 OSCILLATOR LAYOUT
CONSIDERATIONS
11.5
The Timer1 oscillator circuit draws very little power
during operation. Due to the low-power nature of the
oscillator, it may also be sensitive to rapidly changing
signals in close proximity.
The oscillator circuit, shown in Figure 11-3, should be
located as close as possible to the microcontroller.
There should be no circuits passing within the oscillator
circuit boundaries other than VSS or VDD.
If a high-speed circuit must be located near the oscillator (such as the CCP1 pin in Output Compare or PWM
mode, or the primary oscillator using the OSC2 pin), a
grounded guard ring around the oscillator circuit, as
shown in Figure 11-4, may be helpful when used on a
single-sided PCB or in addition to a ground plane.
FIGURE 11-4:
OSCILLATOR CIRCUIT
WITH GROUNDED
GUARD RING
If CCP1 or CCP2 is configured to use Timer1 and to
generate a Special Event Trigger in Compare mode
(CCPxM3:CCPxM0 = 1011), this signal will reset
Timer3. The trigger from CCP2 will also start an A/D
conversion if the A/D module is enabled (see
Section 14.3.4 “Special Event Trigger” for more
information).
The module must be configured as either a timer or a
synchronous counter to take advantage of this feature.
When used this way, the CCPRxH:CCPRxL register
pair effectively becomes a period register for Timer1.
If Timer1 is running in Asynchronous Counter mode,
this Reset operation may not work.
In the event that a write to Timer1 coincides with a
Special Event Trigger, the write operation will take
precedence.
Note:
VDD
VSS
11.6
OSC1
The Special Event Triggers from the CCPx
module will not set the TMR1IF interrupt
flag bit (PIR1<0>).
Using Timer1 as a Real-Time Clock
Adding an external LP oscillator to Timer1 (such as the
one described in Section 11.3 “Timer1 Oscillator”
above) gives users the option to include RTC functionality to their applications. This is accomplished with an
inexpensive watch crystal to provide an accurate time
base and several lines of application code to calculate
the time. When operating in Sleep mode and using a
battery or supercapacitor as a power source, it can
completely eliminate the need for a separate RTC
device and battery backup.
OSC2
RC0
RC1
RC2
Note: Not drawn to scale.
11.4
Resetting Timer1 Using the CCP
Special Event Trigger
Timer1 Interrupt
The TMR1 register pair (TMR1H:TMR1L) increments
from 0000h to FFFFh and rolls over to 0000h. The
Timer1 interrupt, if enabled, is generated on overflow
which is latched in interrupt flag bit, TMR1IF
(PIR1<0>). This interrupt can be enabled or disabled
by setting or clearing the Timer1 Interrupt Enable bit,
TMR1IE (PIE1<0>).
The application code routine, RTCisr, shown in
Example 11-1, demonstrates a simple method to
increment a counter at one-second intervals using an
Interrupt Service Routine. Incrementing the TMR1
register pair to overflow triggers the interrupt and calls
the routine which increments the seconds counter by
one. Additional counters for minutes and hours are
incremented as the previous counter overflows.
Since the register pair is 16 bits wide, counting up to
overflow the register directly from a 32.768 kHz clock
would take 2 seconds. To force the overflow at the
required one-second intervals, it is necessary to preload it. The simplest method is to set the MSb of
TMR1H with a BSF instruction. Note that the TMR1L
register is never preloaded or altered; doing so may
introduce cumulative error over many cycles.
For this method to be accurate, Timer1 must operate in
Asynchronous mode and the Timer1 overflow interrupt
must be enabled (PIE1<0> = 1) as shown in the
routine, RTCinit. The Timer1 oscillator must also be
enabled and running at all times.
DS39770B-page 138
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
EXAMPLE 11-1:
IMPLEMENTING A REAL-TIME CLOCK USING A TIMER1 INTERRUPT SERVICE
RTCinit
MOVLW
MOVWF
CLRF
MOVLW
MOVWF
CLRF
CLRF
MOVLW
MOVWF
BSF
RETURN
80h
TMR1H
TMR1L
b’00001111’
T1CON
secs
mins
.12
hours
PIE1, TMR1IE
; Preload TMR1 register pair
; for 1 second overflow
BSF
BCF
INCF
MOVLW
CPFSGT
RETURN
CLRF
INCF
MOVLW
CPFSGT
RETURN
CLRF
INCF
MOVLW
CPFSGT
RETURN
CLRF
RETURN
TMR1H, 7
PIR1, TMR1IF
secs, F
.59
secs
;
;
;
;
Preload for 1 sec overflow
Clear interrupt flag
Increment seconds
60 seconds elapsed?
;
;
;
;
No, done
Clear seconds
Increment minutes
60 minutes elapsed?
;
;
;
;
No, done
clear minutes
Increment hours
24 hours elapsed?
; Configure for external clock,
; Asynchronous operation, external oscillator
; Initialize timekeeping registers
;
; Enable Timer1 interrupt
RTCisr
TABLE 11-2:
Name
INTCON
secs
mins, F
.59
mins
mins
hours, F
.23
hours
; No, done
; Reset hours
; Done
hours
REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER
Bit 7
Bit 6
GIE/GIEH PEIE/GIEL
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
IPR1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
TMR1L
Timer1 Register Low Byte
52
TMR1H
Timer1 Register High Byte
52
T1CON
RD16
T1RUN
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
TMR1CS
TMR1ON
52
Legend: Shaded cells are not used by the Timer1 module.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 139
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 140
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
12.0
TIMER2 MODULE
12.1
Timer2 Operation
• 8-bit Timer and Period registers (TMR2 and PR2,
respectively)
• Readable and writable (both registers)
• Software programmable prescaler
(1:1, 1:4 and 1:16)
• Software programmable postscaler
(1:1 through 1:16)
• Interrupt on TMR2 to PR2 match
• Optional use as the shift clock for the
MSSP module
In normal operation, TMR2 is incremented from 00h on
each clock (FOSC/4). A 4-bit counter/prescaler on the
clock input gives direct input, divide-by-4 and
divide-by-16 prescale options. These are selected by
the prescaler control bits, T2CKPS1:T2CKPS0
(T2CON<1:0>). The value of TMR2 is compared to that
of the Period register, PR2, on each clock cycle. When
the two values match, the comparator generates a
match signal as the timer output. This signal also resets
the value of TMR2 to 00h on the next cycle and drives
the output counter/postscaler (see Section 12.2
“Timer2 Interrupt”).
The module is controlled through the T2CON register
(Register 12-1) which enables or disables the timer and
configures the prescaler and postscaler. Timer2 can be
shut off by clearing control bit, TMR2ON (T2CON<2>),
to minimize power consumption.
The TMR2 and PR2 registers are both directly readable
and writable. The TMR2 register is cleared on any
device Reset, while the PR2 register initializes at FFh.
Both the prescaler and postscaler counters are cleared
on the following events:
A simplified block diagram of the module is shown in
Figure 12-1.
• a write to the TMR2 register
• a write to the T2CON register
• any device Reset (Power-on Reset, MCLR Reset,
Watchdog Timer Reset or Brown-out Reset)
The Timer2 module incorporates the following features:
TMR2 is not cleared when T2CON is written.
REGISTER 12-1:
T2CON: TIMER2 CONTROL REGISTER
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
T2OUTPS3
T2OUTPS2
T2OUTPS1
T2OUTPS0
TMR2ON
T2CKPS1
T2CKPS0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
Unimplemented: Read as ‘0’
bit 6-3
T2OUTPS3:T2OUTPS0: Timer2 Output Postscale Select bits
0000 = 1:1 Postscale
0001 = 1:2 Postscale
•
•
•
1111 = 1:16 Postscale
bit 2
TMR2ON: Timer2 On bit
1 = Timer2 is on
0 = Timer2 is off
bit 1-0
T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits
00 = Prescaler is 1
01 = Prescaler is 4
1x = Prescaler is 16
© 2007 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39770B-page 141
PIC18F85J90 FAMILY
12.2
Timer2 Interrupt
12.3
Timer2 can also generate an optional device interrupt.
The Timer2 output signal (TMR2 to PR2 match) provides the input for the 4-bit output counter/postscaler.
This counter generates the TMR2 match interrupt flag
which is latched in TMR2IF (PIR1<1>). The interrupt is
enabled by setting the TMR2 Match Interrupt Enable
bit, TMR2IE (PIE1<1>).
Timer2 Output
The unscaled output of TMR2 is available primarily to
the CCP modules, where it is used as a time base for
operations in PWM mode.
Timer2 can be optionally used as the shift clock source
for the MSSP module operating in SPI mode.
Additional information is provided in Section 16.0
“Master Synchronous Serial Port (MSSP) Module”.
A range of 16 postscale options (from 1:1 through 1:16
inclusive) can be selected with the postscaler control
bits, T2OUTPS3:T2OUTPS0 (T2CON<6:3>).
FIGURE 12-1:
TIMER2 BLOCK DIAGRAM
4
1:1 to 1:16
Postscaler
T2OUTPS3:T2OUTPS0
Set TMR2IF
2
TMR2 Output
(to PWM or MSSP)
T2CKPS1:T2CKPS0
TMR2/PR2
Match
Reset
1:1, 1:4, 1:16
Prescaler
FOSC/4
TMR2
Comparator
PR2
8
8
8
Internal Data Bus
TABLE 12-1:
Name
REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER
Bit 7
Bit 6
INTCON GIE/GIEH PEIE/GIEL
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
IPR1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
TMR2
T2CON
PR2
Timer2 Register
—
52
T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON
T2CKPS1 T2CKPS0
Timer2 Period Register
52
52
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Timer2 module.
DS39770B-page 142
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
13.0
TIMER3 MODULE
The Timer3 timer/counter module incorporates these
features:
• Software selectable operation as a 16-bit timer or
counter
• Readable and writable 8-bit registers (TMR3H
and TMR3L)
• Selectable clock source (internal or external) with
device clock or Timer1 oscillator internal options
• Interrupt on overflow
• Module Reset on CCP Special Event Trigger
REGISTER 13-1:
A simplified block diagram of the Timer3 module is
shown in Figure 13-1. A block diagram of the module’s
operation in Read/Write mode is shown in Figure 13-2.
The Timer3 module is controlled through the T3CON
register (Register 13-1). It also selects the clock source
options for the CCP modules. See Section 14.2.2
“Timer1/Timer3 Mode Selection” for more
information.
T3CON: TIMER3 CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RD16
T3CCP2
T3CKPS1
T3CKPS0
T3CCP1
T3SYNC
TMR3CS
TMR3ON
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
RD16: 16-Bit Read/Write Mode Enable bit
1 = Enables register read/write of Timer3 in one 16-bit operation
0 = Enables register read/write of Timer3 in two 8-bit operations
bit 6,3
T3CCP2:T3CCP1: Timer3 and Timer1 to CCPx Enable bits
1x = Timer3 is the capture/compare clock source for the CCP modules
01 = Timer3 is the capture/compare clock source for CCP2;
Timer1 is the capture/compare clock source for CCP1
00 = Timer1 is the capture/compare clock source for the CCP modules
bit 5-4
T3CKPS1:T3CKPS0: Timer3 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
bit 2
T3SYNC: Timer3 External Clock Input Synchronization Control bit
(Not usable if the device clock comes from Timer1/Timer3.)
When TMR3CS = 1:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
When TMR3CS = 0:
This bit is ignored. Timer3 uses the internal clock when TMR3CS = 0.
bit 1
TMR3CS: Timer3 Clock Source Select bit
1 = External clock input from Timer1 oscillator or T13CKI (on the rising edge after the first
falling edge)
0 = Internal clock (FOSC/4)
bit 0
TMR3ON: Timer3 On bit
1 = Enables Timer3
0 = Stops Timer3
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 143
PIC18F85J90 FAMILY
13.1
Timer3 Operation
The operating mode is determined by the clock select
bit, TMR3CS (T3CON<1>). When TMR3CS is cleared
(= 0), Timer3 increments on every internal instruction
cycle (FOSC/4). When the bit is set, Timer3 increments
on every rising edge of the Timer1 external clock input
or the Timer1 oscillator, if enabled.
Timer3 can operate in one of three modes:
• Timer
• Synchronous Counter
• Asynchronous Counter
As
with
Timer1,
the
RC1/T1OSI
and
RC0/T1OSO/T13CKI pins become inputs when the
Timer1 oscillator is enabled. This means the values of
TRISC<1:0> are ignored and the pins are read as ‘0’.
FIGURE 13-1:
TIMER3 BLOCK DIAGRAM (8-BIT MODE)
Timer1 Oscillator
Timer1 Clock Input
1
1
T1OSO/T13CKI
FOSC/4
Internal
Clock
T1OSI
Synchronize
Prescaler
1, 2, 4, 8
0
Detect
0
2
T1OSCEN(1)
Sleep Input
Timer3
On/Off
TMR3CS
T3CKPS1:T3CKPS0
T3SYNC
TMR3ON
CCPx Special Event Trigger
CCPx Select from T3CON<6,3>
Clear TMR3
Set
TMR3IF
on Overflow
TMR3
High Byte
TMR3L
Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain.
FIGURE 13-2:
TIMER3 BLOCK DIAGRAM (16-BIT READ/WRITE MODE)
Timer1 Oscillator
Timer1 Clock Input
1
1
T13CKI/T1OSO
FOSC/4
Internal
Clock
T1OSI
Synchronize
Prescaler
1, 2, 4, 8
0
Detect
0
2
T1OSCEN(1)
Sleep Input
Timer3
On/Off
TMR3CS
T3CKPS1:T3CKPS0
T3SYNC
TMR3ON
CCPx Special Event Trigger
CCPx Select from T3CON<6,3>
Clear TMR3
Set
TMR3IF
on Overflow
TMR3
High Byte
TMR3L
8
Read TMR1L
Write TMR1L
8
8
TMR3H
8
8
Internal Data Bus
Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain.
DS39770B-page 144
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
13.2
Timer3 16-Bit Read/Write Mode
13.4
Timer3 Interrupt
Timer3 can be configured for 16-bit reads and writes
(see Figure 13-2). When the RD16 control bit
(T3CON<7>) is set, the address for TMR3H is mapped
to a buffer register for the high byte of Timer3. A read
from TMR3L will load the contents of the high byte of
Timer3 into the Timer3 High Byte Buffer register. This
provides the user with the ability to accurately read all
16 bits of Timer1 without having to determine whether
a read of the high byte, followed by a read of the low
byte, has become invalid due to a rollover between
reads.
The TMR3 register pair (TMR3H:TMR3L) increments
from 0000h to FFFFh and overflows to 0000h. The
Timer3 interrupt, if enabled, is generated on overflow
and is latched in interrupt flag bit, TMR3IF (PIR2<1>).
This interrupt can be enabled or disabled by setting or
clearing the Timer3 Interrupt Enable bit, TMR3IE
(PIE2<1>).
A write to the high byte of Timer3 must also take place
through the TMR3H Buffer register. The Timer3 high
byte is updated with the contents of TMR3H when a
write occurs to TMR3L. This allows a user to write all
16 bits to both the high and low bytes of Timer3 at once.
If CCP1 or CCP2 is configured to use Timer3 and to
generate a Special Event Trigger in Compare mode
(CCPxM3:CCPxM0 = 1011), this signal will reset
Timer3. The trigger from CCP2 will also start an A/D
conversion if the A/D module is enabled (see
Section 14.3.4 “Special Event Trigger” for more
information).
The high byte of Timer3 is not directly readable or
writable in this mode. All reads and writes must take
place through the Timer3 High Byte Buffer register.
13.5
Resetting Timer3 Using the CCP
Special Event Trigger
Writes to TMR3H do not clear the Timer3 prescaler.
The prescaler is only cleared on writes to TMR3L.
The module must be configured as either a timer or
synchronous counter to take advantage of this feature.
When used this way, the CCPRxH:CCPRxL register
pair effectively becomes a period register for Timer3.
13.3
If Timer3 is running in Asynchronous Counter mode,
the Reset operation may not work.
Using the Timer1 Oscillator as the
Timer3 Clock Source
The Timer1 internal oscillator may be used as the clock
source for Timer3. The Timer1 oscillator is enabled by
setting the T1OSCEN (T1CON<3>) bit. To use it as the
Timer3 clock source, the TMR3CS bit must also be set.
As previously noted, this also configures Timer3 to
increment on every rising edge of the oscillator source.
In the event that a write to Timer3 coincides with a
Special Event Trigger from a CCP module, the write will
take precedence.
Note:
The Special Event Triggers from the CCPx
module will not set the TMR3IF interrupt
flag bit (PIR2<1>).
The Timer1 oscillator is described in Section 11.0
“Timer1 Module”.
TABLE 13-1:
Name
INTCON
REGISTERS ASSOCIATED WITH TIMER3 AS A TIMER/COUNTER
Bit 7
Bit 6
GIE/GIEH PEIE/GIEL
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR2
OSCFIF
CMIF
—
—
BCLIF
LVDIF
TMR3IF
—
54
PIE2
OSCFIE
CMIE
—
—
BCLIE
LVDIE
TMR3IE
—
54
IPR2
OSCFIP
CMIP
—
—
BCLIP
LVDIP
TMR3IP
—
54
TMR3L
Timer3 Register Low Byte
53
TMR3H
Timer3 Register High Byte
53
T1CON
RD16
T1RUN
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
TMR1CS
TMR1ON
52
T3CON
RD16
T3CCP2
T3CKPS1 T3CKPS0
TMR3CS
TMR3ON
53
T3CCP1
T3SYNC
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Timer3 module.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 145
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 146
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
14.0
CAPTURE/COMPARE/PWM
(CCP) MODULES
PIC18F85J90 family devices have two CCP
(Capture/Compare/PWM) modules, designated CCP1
and CCP2. Both modules implement standard Capture,
Compare and Pulse-Width Modulation (PWM) modes.
REGISTER 14-1:
Each CCP module contains a 16-bit register which can
operate as a 16-bit Capture register, a 16-bit Compare
register or a PWM Master/Slave Duty Cycle register.
For the sake of clarity, all CCP module operation in the
following sections is described with respect to CCP2,
but is equally applicable to CCP1.
CCPxCON: CCPx CONTROL REGISTER (CCP1, CCP2 MODULES)
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
DCxB1
DCxB0
CCPxM3
CCPxM2
CCPxM1
CCPxM0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-6
Unimplemented: Read as ‘0’
bit 5-4
DCxB1:DCxB0: PWM Duty Cycle bit 1 and bit 0 for CCPx Module
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two Least Significant bits (bit 1 and bit 0) of the 10-bit PWM duty cycle. The eight
Most Significant bits (DCx9:DCx2) of the duty cycle are found in CCPRxL.
bit 3-0
CCPxM3:CCPxM0: CCPx Module Mode Select bits
0000 = Capture/Compare/PWM disabled (resets CCPx module)
0001 = Reserved
0010 = Compare mode, toggle output on match (CCPxIF bit is set)
0011 = Reserved
0100 = Capture mode, every falling edge
0101 = Capture mode, every rising edge
0110 = Capture mode, every 4th rising edge
0111 = Capture mode, every 16th rising edge
1000 = Compare mode: initialize CCPx pin low; on compare match, force CCPx pin high (CCPxIF bit
is set)
1001 = Compare mode: initialize CCPx pin high; on compare match, force CCPx pin low (CCPxIF bit
is set)
1010 = Compare mode: generate software interrupt on compare match (CCPxIF bit is set, CCPx pin
reflects I/O state)
1011 = Compare mode: Special Event Trigger; reset timer; start A/D conversion on CCPx match
(CCPxIF bit is set)(1)
11xx = PWM mode
Note 1:
CCPxM3:CCPxM0 = 1011 will only reset timer and not start A/D conversion on CCP1 match.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 147
PIC18F85J90 FAMILY
14.1
CCP Module Configuration
Depending on the configuration selected, up to four
timers may be active at once, with modules in the same
configuration (Capture/Compare or PWM) sharing
timer resources. The possible configurations are
shown in Figure 14-1.
Each Capture/Compare/PWM module is associated
with a control register (generically, CCPxCON) and a
data register (CCPRx). The data register in turn is comprised of two 8-bit registers: CCPRxL (low byte) and
CCPRxH (high byte). All registers are both readable
and writable.
14.1.1
14.1.2
When operating in Output mode (i.e., in Compare or
PWM modes), the drivers for the CCPx pins can be
optionally configured as open-drain outputs. This
feature allows the voltage level on the pin to be pulled
to a higher level through an external pull-up resistor
and allows the output to communicate with external
circuits without the need for additional level shifters.
CCP MODULES AND TIMER
RESOURCES
The CCP modules utilize Timers 1, 2 or 3, depending
on the mode selected. Timer1 and Timer3 are available
to modules in Capture or Compare modes, while
Timer2 is available for modules in PWM mode.
TABLE 14-1:
The open-drain output option is controlled by the
CCP2OD and CCP1OD bits (TRISG<6:5>). Setting the
appropriate bit configures the pin for the corresponding
module for open-drain operation.
CCP MODE – TIMER
RESOURCE
CCP Mode
Timer Resource
Capture
Compare
PWM
Timer1 or Timer3
Timer1 or Timer3
Timer2
14.1.3
CCP2 PIN ASSIGNMENT
The pin assignment for CCP2 (Capture input, Compare
and PWM output) can change, based on device configuration. The CCP2MX Configuration bit determines
which pin CCP2 is multiplexed to. By default, it is
assigned to RC1 (CCP2MX = 1). If the Configuration bit
is cleared, CCP2 is multiplexed with RE7.
The assignment of a particular timer to a module is
determined by the Timer to CCP enable bits in the
T3CON register (Register 13-1). Both modules may be
active at any given time and may share the same timer
resource if they are configured to operate in the same
mode (Capture/Compare or PWM) at the same time.
The interactions between the two modules are
summarized in Table 14-2.
FIGURE 14-1:
OPEN-DRAIN OUTPUT OPTION
Changing the pin assignment of CCP2 does not
automatically change any requirements for configuring
the port pin. Users must always verify that the appropriate TRIS register is configured correctly for CCP2
operation, regardless of where it is located.
CCP AND TIMER INTERCONNECT CONFIGURATIONS
T3CCP<2:1> = 00
T3CCP<2:1> = 01
TMR1
TMR1
TMR3
CCP1
TMR3
CCP1
Timer1 is used for all Capture
and Compare operations for
all CCP modules. Timer2 is
used for PWM operations for
all CCP modules. Modules
may share either timer
resource as a common time
base.
DS39770B-page 148
TMR1
TMR3
CCP1
CCP2
TMR2
T3CCP<2:1> = 1x
CCP2
TMR2
Timer1 is used for Capture
and Compare operations for
CCP1 and Timer 3 is used for
CCP2.
Both the modules use Timer2
as a common time base if they
are in PWM modes.
Preliminary
CCP2
TMR2
Timer3 is used for all Capture
and Compare operations for
all CCP modules. Timer2 is
used for PWM operations for
all CCP modules. Modules
may share either timer
resource as a common time
base.
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 14-2:
INTERACTIONS BETWEEN CCP1 AND CCP2 FOR TIMER RESOURCES
CCP1 Mode CCP2 Mode
Interaction
Capture
Capture
Each module can use TMR1 or TMR3 as the time base. The time base can be different
for each CCP.
Capture
Compare
CCP2 can be configured for the Special Event Trigger to reset TMR1 or TMR3
(depending upon which time base is used). Automatic A/D conversions on trigger event
can also be done. Operation of CCP1 could be affected if it is using the same timer as a
time base.
Compare
Capture
CCP1 can be configured for the Special Event Trigger to reset TMR1 or TMR3
(depending upon which time base is used). Operation of CCP2 could be affected if it is
using the same timer as a time base.
Compare
Compare
Either module can be configured for the Special Event Trigger to reset the time base.
Automatic A/D conversions on CCP2 trigger event can be done. Conflicts may occur if
both modules are using the same time base.
Capture
PWM
None
Compare
PWM
None
PWM
Capture
None
PWM
Compare
None
PWM
PWM
Both PWMs will have the same frequency and update rate (TMR2 interrupt).
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 149
PIC18F85J90 FAMILY
14.2
Capture Mode
14.2.3
SOFTWARE INTERRUPT
In Capture mode, the CCPR2H:CCPR2L register pair
captures the 16-bit value of the TMR1 or TMR3 register
when an event occurs on the CCP2 pin (RC1 or RE7,
depending on device configuration). An event is
defined as one of the following:
When the Capture mode is changed, a false capture
interrupt may be generated. The user should keep the
CCP2IE bit (PIE3<2>) clear to avoid false interrupts
and should clear the flag bit, CCP2IF, following any
such change in operating mode.
•
•
•
•
14.2.4
every falling edge
every rising edge
every 4th rising edge
every 16th rising edge
There are four prescaler settings in Capture mode.
They are specified as part of the operating mode
selected by the mode select bits (CCP2M3:CCP2M0).
Whenever the CCP module is turned off, or the CCP
module is not in Capture mode, the prescaler counter
is cleared. This means that any Reset will clear the
prescaler counter.
The event is selected by the mode select bits,
CCP2M3:CCP2M0 (CCP2CON<3:0>). When a
capture is made, the interrupt request flag bit, CCP2IF
(PIR3<2>), is set; it must be cleared in software. If
another capture occurs before the value in register
CCPR2 is read, the old captured value is overwritten by
the new captured value.
14.2.1
Switching from one capture prescaler to another may
generate an interrupt. Also, the prescaler counter will
not be cleared; therefore, the first capture may be from
a non-zero prescaler. Example 14-1 shows the
recommended method for switching between capture
prescalers. This example also clears the prescaler
counter and will not generate the “false” interrupt.
CCP PIN CONFIGURATION
In Capture mode, the appropriate CCPx pin should be
configured as an input by setting the corresponding
TRIS direction bit.
Note:
14.2.2
EXAMPLE 14-1:
If RC1/CCP2 or RE7/CCP2 is configured
as an output, a write to the port can cause
a capture condition.
CHANGING BETWEEN
CAPTURE PRESCALERS
CLRF CCP2CON
; Turn CCP module off
MOVLW NEW_CAPT_PS ; Load WREG with the
; new prescaler mode
; value and CCP ON
MOVWF CCP2CON
; Load CCP2CON with
; this value
TIMER1/TIMER3 MODE SELECTION
The timers that are to be used with the capture feature
(Timer1 and/or Timer3) must be running in Timer mode or
Synchronized Counter mode. In Asynchronous Counter
mode, the capture operation may not work. The timer to
be used with each CCP module is selected in the T3CON
register (see Section 14.1.1 “CCP Modules and Timer
Resources”).
FIGURE 14-2:
CCP PRESCALER
CAPTURE MODE OPERATION BLOCK DIAGRAM
TMR3H
TMR3L
Set CCP1IF
T3CCP2
CCP1 pin
Prescaler
÷ 1, 4, 16
and
Edge Detect
CCPR1H
T3CCP2
4
CCP1CON<3:0>
Q1:Q4
CCP2CON<3:0>
4
TMR3
Enable
CCPR1L
TMR1
Enable
TMR1H
TMR1L
TMR3H
TMR3L
Set CCP2IF
4
T3CCP1
T3CCP2
TMR3
Enable
CCP2 pin
Prescaler
÷ 1, 4, 16
and
Edge Detect
CCPR2H
CCPR2L
TMR1
Enable
T3CCP2
T3CCP1
DS39770B-page 150
Preliminary
TMR1H
TMR1L
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
14.3
14.3.3
Compare Mode
SOFTWARE INTERRUPT MODE
In Compare mode, the 16-bit CCPR2 register value is
constantly compared against either the TMR1 or TMR3
register pair value. When a match occurs, the CCP2
pin can be:
When the Generate Software Interrupt mode is chosen
(CCP2M3:CCP2M0 = 1010), the CCP2 pin is not
affected. Only a CCP interrupt is generated, if enabled,
and the CCP2IE bit is set.
•
•
•
•
14.3.4
driven high
driven low
toggled (high-to-low or low-to-high)
remain unchanged (that is, reflects the state of the
I/O latch)
Both CCP modules are equipped with a Special Event
Trigger. This is an internal hardware signal generated
in Compare mode to trigger actions by other modules.
The Special Event Trigger is enabled by selecting
the Compare Special Event Trigger mode
(CCP2M3:CCP2M0 = 1011).
The action on the pin is based on the value of the mode
select bits (CCP2M3:CCP2M0). At the same time, the
interrupt flag bit, CCP2IF, is set.
14.3.1
For either CCP module, the Special Event Trigger resets
the timer register pair for whichever timer resource is
currently assigned as the module’s time base. This
allows the CCPRx registers to serve as a programmable
period register for either timer.
CCP PIN CONFIGURATION
The user must configure the CCPx pin as an output by
clearing the appropriate TRIS bit.
Note:
14.3.2
SPECIAL EVENT TRIGGER
The Special Event Trigger for CCP2 can also start an
A/D conversion. In order to do this, the A/D converter
must already be enabled.
Clearing the CCP2CON register will force
the RC1 or RE7 compare output latch
(depending on device configuration) to the
default low level. This is not the PORTC or
PORTE I/O data latch.
Note:
TIMER1/TIMER3 MODE SELECTION
The Special Event Trigger of CCP1 only
resets Timer1/Timer3 and cannot start an
A/D conversion even when the A/D
converter is enabled.
Timer1 and/or Timer3 must be running in Timer mode,
or Synchronized Counter mode, if the CCP module is
using the compare feature. In Asynchronous Counter
mode, the compare operation may not work.
FIGURE 14-3:
COMPARE MODE OPERATION BLOCK DIAGRAM
CCPR1H
Special Event Trigger
(Timer1 Reset)
Set CCP1IF
CCPR1L
CCP1 pin
Comparator
Output
Logic
Compare
Match
S
Q
R
TRIS
Output Enable
4
CCP1CON<3:0>
0
TMR1H
TMR1L
0
1
TMR3H
TMR3L
1
Special Event Trigger
(Timer1/Timer3 Reset, A/D Trigger)
T3CCP1
T3CCP2
Set CCP2IF
Comparator
CCPR2H
CCP2 pin
Compare
Match
Output
Logic
4
CCPR2L
S
Q
R
TRIS
Output Enable
CCP2CON<3:0>
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 151
PIC18F85J90 FAMILY
TABLE 14-3:
Name
INTCON
REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, TIMER1 AND TIMER3
Bit 7
Bit 6
Bit 5
GIE/GIEH PEIE/GIEL TMR0IE
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
IPEN
—
—
RI
TO
PD
POR
BOR
52
PIR3
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
54
PIE3
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
54
IPR3
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
54
RCON
PIR2
OSCFIF
CMIF
—
—
BCLIF
LVDIF
TMR3IF
—
54
PIE2
OSCFIE
CMIE
—
—
BCLIE
LVDIE
TMR3IE
—
54
IPR2
OSCFIP
CMIP
—
—
BCLIP
LVDIP
TMR3IP
—
54
TRISC
TRISC7
TRISC6
TRISC5
TRISC4
TRISC3
TRISC2
TRISC1
TRISC0
54
TRISE
TRISE7
TRISE6
TRISE5
TRISG
SPIOD
CCP2OD CCP1OD
TRISE4
TRISE3
—
TRISE1
TRISE0
54
TRISG4
TRISG3
TRISG2
TRISG1
TRISG0
54
TMR1L
Timer1 Register Low Byte
52
TMR1H
Timer1 Register High Byte
52
T1CON
RD16
T1RUN
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
TMR1CS TMR1ON
52
TMR3H
Timer3 Register High Byte
53
TMR3L
Timer3 Register Low Byte
53
T3CON
RD16
T3CCP2
T3CKPS1 T3CKPS0
CCPR1L
Capture/Compare/PWM Register 1 Low Byte
CCPR1H
Capture/Compare/PWM Register 1 High Byte
—
CCP1CON
—
DC1B1
DC1B0
T3CCP1
T3SYNC
TMR3CS TMR3ON
53
55
55
CCP1M3
CCP1M2
CCP1M1
CCP1M0
55
CCPR2L
Capture/Compare/PWM Register 2 Low Byte
56
CCPR2H
Capture/Compare/PWM Register 2 High Byte
55
CCP2CON
—
—
DC2B1
DC2B0
CCP2M3
CCP2M2
CCP2M1
CCP2M0
56
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by Capture/Compare, Timer1 or Timer3.
DS39770B-page 152
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
14.4
PWM Mode
In Pulse-Width Modulation (PWM) mode, the CCP2 pin
produces up to a 10-bit resolution PWM output. Since
the CCP2 pin is multiplexed with a PORTC or PORTE
data latch, the appropriate TRIS bit must be cleared to
make the CCP2 pin an output.
A PWM output (Figure 14-5) has a time base (period)
and a time that the output stays high (duty cycle). The
frequency of the PWM is the inverse of the period
(1/period).
FIGURE 14-5:
PWM OUTPUT
Period
Note:
Clearing the CCP2CON register will force
the RC1 or RE7 output latch (depending
on device configuration) to the default low
level. This is not the PORTC or PORTE
I/O data latch.
Duty Cycle
TMR2 = PR2
Figure 14-4 shows a simplified block diagram of the
CCP1 module in PWM mode.
For a step-by-step procedure on how to set up the CCP
module for PWM operation, see Section 14.4.3
“Setup for PWM Operation”.
FIGURE 14-4:
SIMPLIFIED PWM BLOCK
DIAGRAM
Duty Cycle Registers
TMR2 = Duty Cycle
TMR2 = PR2
14.4.1
PWM PERIOD
The PWM period is specified by writing to the PR2
register. The PWM period can be calculated using the
following formula:
CCP1CON<5:4>
EQUATION 14-1:
CCPR1L
PWM Period = (PR2) + 1] • 4 • TOSC •
(TMR2 Prescale Value)
PWM frequency is defined as 1/[PWM period].
CCPR1H (Slave)
R
Comparator
When TMR2 is equal to PR2, the following three events
occur on the next increment cycle:
Q
RC2/CCP1
TMR2
(Note 1)
S
TRISC<2>
Comparator
PR2
Note 1:
Clear Timer,
CCP1 pin and
latch D.C.
• TMR2 is cleared
• The CCP2 pin is set (exception: if PWM duty
cycle = 0%, the CCP2 pin will not be set)
• The PWM duty cycle is latched from CCPR2L into
CCPR2H
Note:
The 8-bit TMR2 value is concatenated with the 2-bit
internal Q clock, or 2 bits of the prescaler, to create
the 10-bit time base.
© 2007 Microchip Technology Inc.
Preliminary
The Timer2 postscalers (see Section 12.0
“Timer2 Module”) are not used in the
determination of the PWM frequency. The
postscaler could be used to have a servo
update rate at a different frequency than
the PWM output.
DS39770B-page 153
PIC18F85J90 FAMILY
14.4.2
PWM DUTY CYCLE
The PWM duty cycle is specified by writing to the
CCPR2L register and to the CCP2CON<5:4> bits. Up
to 10-bit resolution is available. The CCPR2L contains
the eight MSbs and the CCP2CON<5:4> contains the
two LSbs. This 10-bit value is represented by
CCPR2L:CCP2CON<5:4>. The following equation is
used to calculate the PWM duty cycle in time:
The CCPR2H register and a 2-bit internal latch are
used to double-buffer the PWM duty cycle. This
double-buffering is essential for glitchless PWM
operation.
When the CCPR2H and 2-bit latch match TMR2,
concatenated with an internal 2-bit Q clock or 2 bits of
the TMR2 prescaler, the CCP2 pin is cleared.
The maximum PWM resolution (bits) for a given PWM
frequency is given by the equation:
EQUATION 14-2:
EQUATION 14-3:
PWM Duty Cycle = (CCPR2L:CCP2CON<5:4>) •
TOSC • (TMR2 Prescale Value)
CCPR2L and CCP2CON<5:4> can be written to at any
time, but the duty cycle value is not latched into
CCPR2H until after a match between PR2 and TMR2
occurs (i.e., the period is complete). In PWM mode,
CCPR2H is a read-only register.
TABLE 14-4:
F OSC
log ⎛ ---------------⎞
⎝ F PWM⎠
PWM Resolution (max) = -----------------------------bits
log ( 2 )
Note:
If the PWM duty cycle value is longer than
the PWM period, the CCP2 pin will not be
cleared.
EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 40 MHz
PWM Frequency
Timer Prescaler (1, 4, 16)
PR2 Value
Maximum Resolution (bits)
DS39770B-page 154
2.44 kHz
9.77 kHz
39.06 kHz
156.25 kHz
312.50 kHz
416.67 kHz
16
4
1
1
1
1
FFh
FFh
FFh
3Fh
1Fh
17h
14
12
10
8
7
6.58
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
14.4.3
SETUP FOR PWM OPERATION
3.
The following steps should be taken when configuring
the CCP module for PWM operation:
1.
2.
Set the PWM period by writing to the PR2
register.
Set the PWM duty cycle by writing to the
CCPR2L register and CCP2CON<5:4> bits.
TABLE 14-5:
Name
INTCON
Make the CCP2 pin an output by clearing the
appropriate TRIS bit.
Set the TMR2 prescale value, then enable
Timer2 by writing to T2CON.
Configure the CCP2 module for PWM operation.
4.
5.
REGISTERS ASSOCIATED WITH PWM AND TIMER2
Bit 7
Bit 6
GIE/GIEH PEIE/GIEL
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
—
RI
TO
PD
POR
BOR
52
IPEN
—
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
IPR1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
TRISC
TRISC7
TRISC6
TRISC5
TRISC4
TRISC3
TRISC2
TRISC1
TRISC0
54
TRISE
TRISE7
TRISE6
TRISE5
TRISE4
TRISE3
—
TRISE1
TRISE0
54
TRISG
SPIOD
CCP2OD
CCP1OD
TRISG4
TRISG3
TRISG2
TRISG1
TRISG0
54
RCON
TMR2
Timer2 Register
52
PR2
Timer2 Period Register
52
T2CON
—
T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0
52
CCPR1L
Capture/Compare/PWM Register 1 Low Byte
55
CCPR1H
Capture/Compare/PWM Register 1 High Byte
55
CCP1CON
—
—
DC1B1
DC1B0
CCPR2L
Capture/Compare/PWM Register 2 Low Byte
CCPR2H
Capture/Compare/PWM Register 2 High Byte
CCP2CON
—
—
DC2B1
DC2B0
CCP1M3
CCP1M2
CCP1M1 CCP1M0
55
56
55
CCP2M3
CCP2M2
CCP2M1 CCP2M0
56
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PWM or Timer2.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 155
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 156
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
15.0
LIQUID CRYSTAL DISPLAY
(LCD) DRIVER MODULE
The LCD driver module supports these features:
• Direct driving of LCD panel
• On-chip bias generator with dedicated charge
pump to support a range of fixed and variable bias
options
• Up to four commons, with four Multiplexing modes
• Up to 48 (80-pin devices) or 33 (64-pin devices)
segments
• Three LCD clock sources with selectable prescaler,
with a fourth source available for use with the LCD
charge pump
The Liquid Crystal Display (LCD) driver module
generates the timing control to drive a static or
multiplexed LCD panel. It also provides control of the
LCD pixel data. The module can drive panels of up to
192 pixels (48 segments by 4 commons) in 80-pin
devices, and 132 pixels (33 segments by 4 commons) in
64-pin devices.
A simplified block diagram of the module is shown in
Figure 15-1.
FIGURE 15-1:
LCD DRIVER MODULE BLOCK DIAGRAM
Data Bus
LCD DATA
24 x 8 (= 4 x 48)
8
LCDDATA23
192
LCDDATA22
.
.
.
LCDDATA1
to
48
48
SEG<47:0>
MUX
LCDDATA0
Bias
Voltage
To I/O Pins
Timing Control
4
LCDCON
LCDPS
LCDSEx
COM3:COM0
LCD Bias Generation
FOSC/4
T13CKI
INTRC Oscillator
INTOSC Oscillator
© 2007 Microchip Technology Inc.
LCD Clock
Source Select
LCD
Charge Pump
Preliminary
DS39770B-page 157
PIC18F85J90 FAMILY
15.1
LCD Registers
The LCDPS register, shown in Register 15-2,
configures the LCD clock source prescaler and the type
of waveform: Type-A or Type-B. Details on these
features are provided in Section 15.2 “LCD Clock
Source”, Section 15.3 “LCD Bias Generation” and
Section 15.8 “LCD Waveform Generation”.
The LCD driver module has 33 registers:
•
•
•
•
LCD Control Register (LCDCON)
LCD Phase Register (LCDPS)
LCDREG Register (LCD Regulator Control)
Six LCD Segment Enable Registers
(LCDSE5:LCDSE0)
• 24 LCD Data Registers
(LCDDATA23:LCDDATA0)
15.1.1
The LCDREG register is described in Section 15.3
“LCD Bias Generation”.
LCD CONTROL REGISTERS
The LCDCON register, shown in Register 15-1,
controls the overall operation of the module. Once the
module is configured, the LCDEN (LCDCON<7>) bit is
used to enable or disable the LCD module. The LCD
panel can also operate during Sleep by clearing the
SLPEN (LCDCON<6>) bit.
REGISTER 15-1:
The LCD Segment Enable registers (LCDSEx)
configure the functions of the port pins. Setting the
segment enable bit for a particular segment configures
that pin as an LCD driver. The prototype LCDSE
register is shown in Register 15-3. There are six
LCDSE registers (LCDSE5:LCDSE0), listed in
Table 15-1.
LCDCON: LCD CONTROL REGISTER
R/W-0
R/W-0
R/C-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
LCDEN
SLPEN
WERR
—
CS1
CS0
LMUX1
LMUX0
bit 7
bit 0
Legend:
C = Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
LCDEN: LCD Driver Enable bit
1 = LCD driver module is enabled
0 = LCD driver module is disabled
bit 6
SLPEN: LCD Driver Enable in Sleep mode bit
1 = LCD driver module is disabled in Sleep mode
0 = LCD driver module is enabled in Sleep mode
bit 5
WERR: LCD Write Failed Error bit
1 = LCDDATAx register written while LCDPS<4> = 0 (must be cleared in software)
0 = No LCD write error
bit 4
Unimplemented: Read as ‘0’
bit 3-2
CS1:CS0: Clock Source Select bits
1x = INTRC (31 kHz)
01 = T13CKI (Timer1)
00 = System clock (FOSC/4)
bit 1-0
LMUX1:LMUX0: Commons Select bits
Maximum Number of Pixels:
LMUX1:
LMUX0
Multiplex Type
00
DS39770B-page 158
Bias Type
PIC18F6XJ90
PIC18F8XJ90
Static (COM0)
33
48
Static
01
1/2 (COM1:COM0)
66
96
1/2 or 1/3
10
1/3 (COM2:COM0)
99
144
1/2 or 1/3
11
1/4 (COM3:COM0)
132
192
1/3
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 15-2:
LCDPS: LCD PHASE REGISTER
R/W-0
R/W-0
R-0
R-0
R/W-0
R/W-0
R/W-0
R/W-0
WFT
BIASMD
LCDA
WA
LP3
LP2
LP1
LP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
WFT: Waveform Type Select bit
1 = Type-B waveform (phase changes on each frame boundary)
0 = Type-A waveform (phase changes within each common type)
bit 6
BIASMD: Bias Mode Select bit
When LMUX1:LMUX0 = 00:
0 = Static Bias mode (do not set this bit to ‘1’)
When LMUX1:LMUX0 = 01 or 10:
1 = 1/2 Bias mode
0 = 1/3 Bias mode
When LMUX1:LMUX0 = 11:
0 = 1/3 Bias mode (do not set this bit to ‘1’)
bit 5
LCDA: LCD Active Status bit
1 = LCD driver module is active
0 = LCD driver module is inactive
bit 4
WA: LCD Write Allow Status bit
1 = Write into the LCDDATAx registers is allowed
0 = Write into the LCDDATAx registers is not allowed
bit 3-0
LP3:LP0: LCD Prescaler Select bits
1111 = 1:16
1110 = 1:15
1101 = 1:14
1100 = 1:13
1011 = 1:12
1010 = 1:11
1001 = 1:10
1000 = 1:9
0111 = 1:8
0110 = 1:7
0101 = 1:6
0100 = 1:5
0011 = 1:4
0010 = 1:3
0001 = 1:2
0000 = 1:1
© 2007 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39770B-page 159
PIC18F85J90 FAMILY
REGISTER 15-3:
LCDSEx: LCD SEGMENT ENABLE REGISTERS
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SE(n + 7)
SE(n + 6)
SE(n + 5)
SE(n + 4)
SE(n + 3)
SE(n + 2)
SE(n + 1)
SE(n)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
SEG(n + 7):SEG(n): Segment Enable bits
For LCDSE0: n = 0
For LCDSE1: n = 8
For LCDSE2: n = 16
For LCDSE3: n = 24
For LCDSE4: n = 32
For LCDSE5: n = 40
1 = Segment function of the pin is enabled, digital I/O disabled
0 = I/O function of the pin is enabled
TABLE 15-1:
Note 1:
2:
x = Bit is unknown
LCDSE REGISTERS AND ASSOCIATED SEGMENTS
Register
Segments
LCDSE0
7:0
LCDSE1
15:8
LCDSE2
23:16
LCDSE3
31:24
LCDSE4(1)
39:32
LCDSE5(2)
47:40
LCDSE4<7:1> (SEG39:SEG33) are not implemented in 64-pin devices.
LCDSE5 is not implemented in 64-pin devices.
DS39770B-page 160
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
15.1.2
LCD DATA REGISTERS
Individual LCDDATA bits are named by the convention
“SxxCy”, with “xx” as the segment number and “y” as
the common number. The relationship is summarized
in Table 15-2. The prototype LCDDATA register is
shown in Register 15-4.
Once the module is initialized for the LCD panel, the
individual bits of the LCDDATA23:LCDDATA0 registers
are cleared or set to represent a clear or dark pixel,
respectively. Specific sets of LCDDATA registers are
used with specific segments and common signals.
Each bit represents a unique combination of a specific
segment connected to a specific common.
REGISTER 15-4:
Note:
In 64-pin devices, writing into the registers
LCDDATA5, LCDDATA11, LCDDATA17,
and LCDDATA23 will not affect the status
of any pixels.
LCDDATAx: LCD DATA REGISTERS
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
S(n + 7)Cy
S(n + 6)Cy
S(n + 5)Cy
S(n + 4)Cy
S(n + 3)Cy
S(n + 2)Cy
S(n + 1)Cy
S(n)Cy
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
S(n + 7)Cy:S(n)Cy: Pixel On bits
For LCDDATA0 through LCDDATA5: n = (8x), y = 0
For LCDDATA6 through LCDDATA11: n = (8(x – 6)), y = 1
For LCDDATA12 through LCDDATA17: n = (8(x – 12)), y = 2
For LCDDATA18 through LCDDATA23: n = (8(x – 18)), y = 3
1 = Pixel on (dark)
0 = Pixel off (clear)
TABLE 15-2:
LCDDATA REGISTERS AND BITS FOR SEGMENT AND COM COMBINATIONS
COM Lines
Segments
0 through 7
8 through 15
16 through 23
24 through 31
32 through 39
40 through 47
Note 1:
2:
0
1
2
3
LCDDATA0
LCDDATA6
LCDDATA12
LCDDATA18
S00C0:S07C0
S00C1:S07C1
S00C2:S07C2
S00C3:S07C3
LCDDATA1
LCDDATA7
LCDDATA13
LCDDATA19
S08C0:S15C0
S08C1:S15C1
S08C2:S15C2
S08C0:S15C3
LCDDATA2
LCDDATA8
LCDDATA14
LCDDATA20
S16C0:S23C0
S16C1:S23C1
S16C2:S23C2
S16C3:S23C3
LCDDATA3
LCDDATA9
LCDDATA15
LCDDATA21
S24C0:S31C0
S24C1:S31C1
S24C2:S31C2
S24C3:S31C3
LCDDATA4(1)
LCDDATA10(1)
LCDDATA16(1)
LCDDATA22(1)
S32C0:S39C0
S32C1:S39C1
S32C2:S39C2
S32C3:S39C3
LCDDATA5(2)
LCDDATA11(2)
LCDDATA17(2)
LCDDATA23(2)
S40C0:S47C0
S40C1:S47C1
S40C2:S47C2
S40C3:S47C3
Bits<7:1> of these registers are not implemented in 64-pin devices. Bit 0 of these registers (SEG32Cy) is
always implemented.
These registers are not implemented on 64-pin devices.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 161
PIC18F85J90 FAMILY
15.2
LCD Clock Source
The charge pump clock can use either the Timer1
oscillator or the INTRC source, as well as the 8 MHz
INTOSC source (after being divided by 256 by a
prescaler). The charge pump clock source is configured
using the CKSEL1:CKSEL0 bits (LCDREG<1:0>).
The LCD driver module generates its internal clock
from 3 possible sources:
• System clock (FOSC/4)
• Timer1 oscillator
• INTRC source
15.2.2
The LCD clock generator uses a configurable
divide-by-32/divide-by-8192 postscaler to produce a
baseline frequency of about 1 kHz nominal, regardless
of the source selected. The clock source selection and
the postscaler configuration are determined by the
Clock Source Select bits, CS1:CS0 (LCDCON<3:2>).
When using the system clock as the LCD clock source,
it is assumed that the system clock frequency is a nominal 32 MHz (for a FOSC/4 frequency of 8 MHz).
Because the prescaler option for the FOSC/4 clock
selection is fixed at divide-by-8192, system clock
speeds that differ from 32 MHz will produce frame
frequencies and refresh rates different than discussed
in this chapter. The user will need to keep this in mind
when designing the display application.
An additional programmable prescaler is used to derive
the LCD frame frequency from the 1 kHz baseline. The
prescaler is configured using the LP3:LP0 bits
(LCDPS<3:0>) for any one of 16 options, ranging from
1:1 to 1:16.
The Timer1 and INTRC sources can be used as LCD
clock sources when the device is in Sleep mode. To
use the Timer1 oscillator, it is necessary to set the
T1OSCEN bit (T1CON<3>). Selecting either Timer1 or
INTRC as the LCD clock source will not automatically
activate these sources.
Proper timing for waveform generation is set by the
LMUX1:LMUX0 bits (LCDCON<1:0>). These bits
determine which Commons Multiplexing mode is to be
used, and divide down the LCD clock source as
required. They also determine the configuration of the
ring counter that is used to switch the LCD commons
on or off.
15.2.1
Similarly, selecting the INTOSC as the charge pump
clock source will not turn the oscillator on. To use
INTOSC, it must be selected as the system clock
source by using the FOSC2 Configuration bit.
LCD VOLTAGE REGULATOR
CLOCK SOURCE
If Timer1 is used as a clock source for the device, either
as an LCD clock source or for any other purpose, LCD
segment 32 become unavailable.
In addition to the clock source for LCD timing, a
separate 31 kHz nominal clock is required for the LCD
charge pump. This is provided from a distinct branch of
the LCD clock source.
FIGURE 15-2:
CLOCK SOURCE
CONSIDERATIONS
LCD CLOCK GENERATION
2
LCDCON<3:2>
System Clock (FOSC/4)
00
Timer1 Oscillator
01
Internal 31 kHz Source
1x
÷4
00
÷2
01
LCDPS<3:0>
4
1:1 to 1:16
Programmable
Prescaler
10
÷32
or
÷8192
÷1, 2, 3, 4
Ring Counter
COM0
COM1
COM2
COM3
11
2
LCDCON<1:0>
2
LCDREG<1:0>
11
INTOSC 8 MHz Source
÷256
10
31 kHz Clock
to LCD Charge Pump
01
DS39770B-page 162
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
15.3
15.3.2
LCD Bias Generation
LCD VOLTAGE REGULATOR
The LCD driver module is capable of generating the
required bias voltages for LCD operation with a minimum of external components. This includes the ability
to generate the different voltage levels required by the
different bias types required by the LCD. The driver
module can also provide bias voltages both above and
below microcontroller VDD through the use of an
on-chip LCD voltage regulator.
The purpose of the LCD regulator is to provide proper
bias voltage and good contrast for the LCD, regardless
of VDD levels. This module contains a charge pump and
internal voltage reference. The regulator can be configured by using external components to boost bias
voltage above VDD. It can also operate a display at a
constant voltage below VDD. The regulator can also be
selectively disabled to allow bias voltages to be
generated by an external resistor network.
15.3.1
The LCD regulator is controlled through the LCDREG
register (Register 15-5). It is enabled or disabled using
the CKSEL1:CKSEL0 bits, while the charge pump can
be selectively enabled using the CPEN bit. When the
regulator is enabled, the MODE13 bit is used to select
the bias type. The peak LCD bias voltage, measured as
a difference between the potentials of LCDBIAS3 and
LCDBIAS0, is configured with the BIAS bits.
LCD BIAS TYPES
PIC18F85J90 family devices support three bias types
based on the waveforms generated to control
segments and commons:
• Static (two discrete levels)
• 1/2 Bias (three discrete levels
• 1/3 Bias (four discrete levels)
The use of different waveforms in driving the LCD is discussed in more detail in Section 15.8 “LCD Waveform
Generation”.
REGISTER 15-5:
LCDREG: VOLTAGE REGULATOR CONTROL REGISTER
U-0
RW-0
RW-1
RW-1
RW-1
RW-1
RW-0
RW-0
—
CPEN
BIAS2
BIAS1
BIAS0
MODE13
CKSEL1
CKSEL0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
Unimplemented: Read as ‘0’
bit 6
CPEN: LCD Charge Pump Enable bit
1 = Charge pump enabled; highest LCD bias voltage is 3.6V
0 = Charge pump disabled; highest LCD bias voltage is AVDD
bit 5-3
BIAS2:BIAS0: Regulator Voltage Output Control bits
111 = 3.60V peak (offset on LCDBIAS0 of 0V)
110 = 3.47V peak (offset on LCDBIAS0 of 0.13V)
101 = 3.34V peak (offset on LCDBIAS0 of 0.26V)
100 = 3.21V peak (offset on LCDBIAS0 of 0.39V)
011 = 3.08V peak (offset on LCDBIAS0 of 0.52V)
010 = 2.95V peak (offset on LCDBIAS0 of 0.65V)
001 = 2.82V peak (offset on LCDBIAS0 of 0.78V)
000 = 2.69V peak (offset on LCDBIAS0 of 0.91V)
bit 2
MODE13: 1/3 LCD Bias Enable bit
1 = Regulator output supports 1/3 LCD Bias mode
0 = Regulator output supports static LCD Bias mode
bit 1-0
CKSEL1:CKSEL0: Regulator Clock Source Select bits
11 = INTRC
10 = INTOSC 8 MHz source
01 = Timer1 oscillator
00 = LCD regulator disabled
© 2007 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39770B-page 163
PIC18F85J90 FAMILY
15.3.3
BIAS CONFIGURATIONS
M0 is enabled by selecting a valid regulator clock
source (CKSEL<1:0> set to any value except ‘00’) and
setting the CPEN bit. If static Bias type is required, the
MODE13 bit must be cleared.
PIC18F85J90 family devices have four distinct circuit
configurations for LCD bias generation:
•
•
•
•
M0: Regulator with Boost
M1: Regulator without Boost
M2: Resistor Ladder with Software Contrast
M3: Resistor Ladder with Hardware Contrast
15.3.3.1
15.3.3.2
M1 operation is similar to M0, but does not use the LCD
charge pump. It can provide VBIAS up to the voltage
level supplied directly to LCDBIAS3. It can be used in
cases where VDD for the application is expected to
never drop below a level that can provide adequate
contrast for the LCD. The connection of external components is very similar to M0, except that LCDBIAS3
must be tied directly to VDD (Figure 15-3).
M0 (Regulator with Boost)
In M0 operation, the LCD charge pump feature is
enabled. This allows the regulator to generate voltages
up to +3.6V to the LCD (as measured at LCDBIAS3).
M0 uses a flyback capacitor connected between
VLCAP1 and VLCAP2, as well as filter capacitors on
LCDBIAS0 through LCDBIAS3, to obtain the required
voltage boost (Figure 15-3). The output voltage (VBIAS)
is the difference of potential between LCDBIAS3 and
LCDBIAS0. It is set by the BIAS2:BIAS0 bits which
adjust the offset between LCDBIAS0 and VSS. The flyback capacitor (CFLY) acts as a charge storage element for large LCD loads. This mode is useful in those
cases where the voltage requirements of the LCD are
higher than the microcontroller’s VDD. It also permits
software control of the display’s contrast by adjustment
of bias voltage by changing the value of the BIAS bits.
The BIAS<2:0> bits can still be used to adjust contrast
in software by changing VBIAS. As with M0, changing
these bits changes the offset between LCDBIAS0 and
VSS. In M1, this is reflected in the change between the
LCDBIAS0 and the voltage tied to LCDBIAS3. Thus, if
VDD should change, VBIAS will also change; where in
M0, the level of VBIAS is constant.
Like M0, M1 supports Static and 1/3 Bias
types.Generation of the voltage levels for 1/3 Bias is
handled automatically but must be configured in
software.
M1 is enabled by selecting a valid regulator clock
source (CKSEL<1:0> set to any value except ‘00’) and
clearing the CPEN bit. If 1/3 Bias type is required, the
MODE13 bit should also be set.
M0 supports Static and 1/3 Bias types. Generation of
the voltage levels for 1/3 Bias is handled automatically,
but must be configured in software.
FIGURE 15-3:
M1 (Regulator without Boost)
LCD REGULATOR CONNECTIONS FOR M0 AND M1 CONFIGURATIONS
VDD
PIC18F85J90
VDD
AVDD
VLCAP1
VLCAP2
CFLY
0.047 μF(1)
CFLY
0.047 μF(1)
VDD
LCDBIAS3
LCDBIAS2
LCDBIAS1
LCDBIAS0
C3
0.047 μF(1)
C2
0.047 μF(1)
C2
0.047 μF(1)
C1
0.047 μF(1)
C1
0.047 μF(1)
C0
0.047 μF(1)
C0
0.047 μF(1)
Mode 0
(VBIAS up to 3.6V)
Note 1:
Mode 1
(VBIAS ≤ VDD)
These values are provided for design guidance only; they should be optimized for the application by the designer
based on the actual LCD specifications.
DS39770B-page 164
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
15.3.3.3
M2 (Resistor Ladder with
Software Contrast)
configuration of the resistor ladder. Most applications
using M2 will use a 1/3 or 1/2 Bias type. While Static
Bias can also be used, it offers extremely limited
contrast range and additional current consumption
over other bias generation modes.
M2 operation also uses the LCD regulator but disables
the charge pump. The regulator’s internal voltage reference remains active as a way to regulate contrast. It is
used in cases where the current requirements of the
LCD exceed the capacity of the regulator’s charge
pump.
Like M1, the LCDBIAS bits can be used to control contrast, limited by the level of VDD supplied to the device.
Also, since there is no capacitor required across
VLCAP1 and VLCAP2, these pins are available as digital
I/O ports, RG2 and RG3.
In this configuration, the LCD bias voltage levels are
created by an external resistor voltage divider
connected across LCDBIAS0 through LCDBIAS3, with
the top of the divider tied to VDD (Figure 15-4). The
potential at the bottom of the ladder is determined by
the LCD regulator’s voltage reference, tied internally to
LCDBIAS0. The bias type is determined by the voltages on the LCDBIAS pins, which are controlled by the
FIGURE 15-4:
M2 is selected by clearing the CKSEL<1:0> bits and
setting the CPEN bit.
RESISTOR LADDER CONNECTIONS FOR CONFIGURATION M2
PIC18F85J90
VDD
AVDD
LCDBIAS3
10 kΩ(1)
10 kΩ(1)
LCDBIAS2
10 kΩ(1)
LCDBIAS1
10 kΩ(1)
10 kΩ(1)
LCDBIAS0
1/2 Bias
1/3 Bias
Bias Type
Bias Level at Pin
Note 1:
1/2 Bias
1/3 Bias
LCDBIAS0
(Internal low reference voltage)
(Internal low reference voltage)
LCDBIAS1
1/2 VBIAS
1/3 VBIAS
LCDBIAS2
1/2 VBIAS
2/3 VBIAS
LCDBIAS3
VBIAS (up to AVDD)
VBIAS (up to AVDD)
These values are provided for design guidance only; they should be optimized for the application by the designer
based on the actual LCD specifications.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 165
PIC18F85J90 FAMILY
15.3.3.4
M3 (Hardware Contrast)
In M3, the LCD regulator is completely disabled. Like
M2, LCD bias levels are tied to AVDD, and are generated
using an external divider. The difference is that the internal voltage reference is also disabled and the bottom of
the ladder is tied to ground (VSS); see Figure 15-5. The
value of the resistors and the difference between VSS
and VDD determine the contrast range; no software
adjustment is possible. This configuration is also used
where the LCD’s current requirements exceed the
capacity of the charge pump, and software contrast
control is not needed.
FIGURE 15-5:
Depending on the bias type required, resistors are
connected between some or all of the pins. A potentiometer can also be connected between LCDBIAS3 and
VDD to allow for hardware controlled contrast
adjustment.
M3 is selected by clearing the CKSEL<1:0> and CPEN
bits.
RESISTOR LADDER CONNECTIONS FOR CONFIGURATION M3
PIC18F85J90
VDD
AVDD
(2)
LCDBIAS3
10 kΩ(1)
10 kΩ(1)
LCDBIAS2
10 kΩ(1)
LCDBIAS1
10 kΩ(1)
10 kΩ(1)
LCDBIAS0
Static Bias
1/2 Bias
1/3 Bias
Bias Type
Bias Level at Pin
Static
Note 1:
2:
1/2 Bias
1/3 Bias
LCDBIAS0
AVSS
AVSS
AVSS
LCDBIAS1
AVSS
1/2 AVDD
1/3 AVDD
LCDBIAS2
AVDD
1/2 AVDD
2/3 AVDD
LCDBIAS3
AVDD
AVDD
AVDD
These values are provided for design guidance only; they should be optimized for the application by the
designer based on the actual LCD specifications.
Potentiometer for manual contrast adjustment is optional; it may be omitted entirely.
DS39770B-page 166
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
15.3.4
DESIGN CONSIDERATIONS FOR
THE LCD CHARGE PUMP
When designing applications that use the LCD regulator with the charge pump enabled, users must always
consider both the dynamic current and RMS (static)
current requirements of the display, and what the
charge pump can deliver. Both dynamic and static
current can be determined by Equation 15-1:
EQUATION 15-1:
I=Cx
dV
dT
For dynamic current, C is the value of the capacitors
attached to LCDBIAS3 and LCDBIAS2. The variable,
dV, is the voltage drop allowed on C2 and C3 during a
voltage switch on the LCD display, and dT is the duration of the transient current after a clock pulse occurs.
For practical design purposes, these will be assumed
to be 0.047 μF for C, 0.1V for dV and 1 μs for dT. This
yields a dynamic current of 4.7 mA for 1 μs.
RMS current is determined by the value of CFLY for C,
the voltage across VLCAP1 and VLCAP2 for dV and the
regulator clock period (TPER) for dT. Assuming CFLY of
0.047 μF, a value of 1.02V across CFLY and TPER of
30 μs, the maximum theoretical static current will be
1.8 mA. Since the charge pump must charge five
capacitors, the maximum current becomes 360 μA. For
a real-world assumption of 50% efficiency, this yields a
practical current of 180 μA.
Users should compare the calculated current capacity
against the requirements of the LCD. While dV and dT
are relatively fixed by device design, the values of CFLY
and the capacitors on the LCDBIAS pins can be
changed to increase or decrease current. As always,
any changes should be evaluated in the actual circuit
for its impact on the application.
15.4
LCD Multiplex Types
The LCD driver module can be configured into four
multiplex types:
•
•
•
•
Static (only COM0 used)
1/2 multiplex (COM0 and COM1 are used)
1/3 multiplex (COM0, COM1 and COM2 are used)
1/4 multiplex (all COM0, COM1, COM2 and COM3
are used)
The number of active commons used is configured by
the LMUX1:LMUX0 bits (LCDCON<1:0>), which determines the function of the PORTE<6:4> pins (see
Table 15-3 for details). If the pin is configured as a COM
drive, the port I/O function is disabled and the TRIS
setting of that pin is overridden.
Note:
On a Power-on Reset, the LMUX1:LMUX0
bits are ‘00’.
TABLE 15-3:
PORTE<6:4> FUNCTION
LMUX1:
LMUX0
PORTE<6>
PORTE<5>
PORTE<4>
00
Digital I/O
Digital I/O
Digital I/O
01
Digital I/O
Digital I/O
COM1 Driver
10
Digital I/O
11
15.5
COM2 Driver COM1 Driver
COM3 Driver COM2 Driver COM1 Driver
Segment Enables
The LCDSEx registers are used to select the pin
function for each segment pin. Setting a bit configures
the corresponding pin to function as a segment driver.
LCDSEx registers do not override the TRIS bit settings,
so the TRIS bits must be configured as input for that
pin.
Note:
15.6
On a Power-on Reset, these pins are
configured as digital I/O.
Pixel Control
The LCDDATAx registers contain bits which define the
state of each pixel. Each bit defines one unique pixel.
Table 15-2 shows the correlation of each bit in the
LCDDATAx registers to the respective common and
segment signals. Any LCD pixel location not being
used for display can be used as general purpose RAM.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 167
PIC18F85J90 FAMILY
15.7
LCD Frame Frequency
15.8
The rate at which the COM and SEG outputs changes
is called the LCD frame frequency. Frame frequency is
set by the LP3:LP0 bits (LCDPS<3:0>), and is also
affected by the Multiplex mode being used. The relationship between the Multiplex mode, LP bits setting
and frame rate is shown in Table 15-4 and Table 15-5.
TABLE 15-4:
FRAME FREQUENCY
FORMULAS
Multiplex
Mode
Frame Frequency (Hz)
Static
Clock source/(4 x 1 x (LP3:LP0 + 1))
1/2
Clock source/(2 x 2 x (LP3:LP0 + 1))
1/3
Clock source/(1 x 3 x (LP3:LP0 + 1))
1/4
Clock source/(1 x 4 x (LP3:LP0 + 1))
TABLE 15-5:
APPROXIMATE FRAME
FREQUENCY (IN Hz) FOR LP
PRESCALER SETTINGS
Multiplex Mode
LP3:LP0
Static
1/2
1/3
1/4
1
125
125
167
125
2
83
83
111
83
3
62
62
83
62
4
50
50
67
50
5
42
42
56
42
6
36
36
48
36
7
31
31
42
31
LCD Waveform Generation
LCD waveform generation is based on the principle
that the net AC voltage across the dark pixel should be
maximized and the net AC voltage across the clear
pixel should be minimized. The net DC voltage across
any pixel should be zero.
The COM signal represents the time slice for each
common, while the SEG contains the pixel data. The
pixel signal (COM-SEG) will have no DC component
and it can take only one of the two rms values. The
higher rms value will create a dark pixel and a lower
rms value will create a clear pixel.
As the number of commons increases, the delta
between the two rms values decreases. The delta
represents the maximum contrast that the display can
have.
The LCDs can be driven by two types of waveform:
Type-A and Type-B. In the Type-A waveform, the
phase changes within each common type, whereas in
the Type-B waveform, the phase changes on each
frame boundary. Thus, the Type-A waveform maintains
0 VDC over a single frame, whereas the Type-B
waveform takes two frames.
Note 1: If the power-managed Sleep mode is
invoked while the LCD Sleep bit is set
(LCDCON<6> is ‘1’), take care to execute
Sleep only when the VDC on all the pixels
is ‘0’.
2: When the LCD clock source is the system
clock, the LCD module will go to Sleep if
the microcontroller goes into Sleep mode,
regardless of the setting of the SPLEN bit.
Thus, always take care to see that the VDC
on all pixels is ‘0’ whenever Sleep mode is
invoked.
Figure 15-6 through Figure 15-16 provide waveforms
for static, half multiplex, one-third multiplex and quarter
multiplex drives for Type-A and Type-B waveforms.
DS39770B-page 168
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 15-6:
TYPE-A/TYPE-B WAVEFORMS IN STATIC DRIVE
V1
COM0
V0
COM0
V1
SEG0
V0
V1
SEG1
SEG1
SEG0
SEG2
SEG7
SEG6
SEG5
SEG4
SEG3
V0
V1
V0
COM0-SEG0
-V1
COM0-SEG1
V0
1 Frame
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 169
PIC18F85J90 FAMILY
FIGURE 15-7:
TYPE-A WAVEFORMS IN 1/2 MUX, 1/2 BIAS DRIVE
V2
COM0
V1
V0
COM1
V2
COM0
COM1
V1
V0
V2
V1
SEG0
V0
SEG0
SEG1
SEG2
SEG3
V2
V1
SEG1
V0
V2
V1
V0
COM0-SEG0
-V1
-V2
V2
V1
V0
COM0-SEG1
-V1
-V2
1 Frame
DS39770B-page 170
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 15-8:
TYPE-B WAVEFORMS IN 1/2 MUX, 1/2 BIAS DRIVE
V2
V1
COM0
COM1
V0
COM0
V2
COM1
V1
V0
V2
SEG0
V1
V0
SEG0
SEG1
SEG2
SEG3
V2
SEG1
V1
V0
V2
V1
V0
COM0-SEG0
-V1
-V2
V2
V1
V0
COM0-SEG1
-V1
-V2
2 Frames
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 171
PIC18F85J90 FAMILY
FIGURE 15-9:
TYPE-A WAVEFORMS IN 1/2 MUX, 1/3 BIAS DRIVE
V3
V2
COM0
V1
COM1
V0
V3
COM0
V2
COM1
V1
V0
V3
V2
SEG0
V1
V0
V3
SEG0
SEG1
SEG2
SEG3
V2
SEG1
V1
V0
V3
V2
V1
V0
COM0-SEG0
-V1
-V2
-V3
V3
V2
V1
V0
COM0-SEG1
-V1
-V2
1 Frame
DS39770B-page 172
Preliminary
-V3
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 15-10:
TYPE-B WAVEFORMS IN 1/2 MUX, 1/3 BIAS DRIVE
V3
V2
COM0
V1
COM1
V0
V3
COM0
V2
COM1
V1
V0
V3
V2
SEG0
V1
V0
V3
SEG0
SEG1
SEG2
SEG3
V2
SEG1
V1
V0
V3
V2
V1
V0
COM0-SEG0
-V1
-V2
-V3
V3
V2
V1
V0
COM0-SEG1
-V1
-V2
2 Frames
© 2007 Microchip Technology Inc.
Preliminary
-V3
DS39770B-page 173
PIC18F85J90 FAMILY
FIGURE 15-11:
TYPE-A WAVEFORMS IN 1/3 MUX, 1/2 BIAS DRIVE
V2
COM0
V1
V0
COM2
V2
COM1
V1
V0
COM1
COM0
V2
COM2
V1
V0
V2
SEG0
SEG2
V1
SEG0
SEG1
SEG2
V0
V2
SEG1
V1
V0
V2
V1
V0
COM0-SEG0
-V1
-V2
V2
V1
V0
COM0-SEG1
-V1
-V2
1 Frame
DS39770B-page 174
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 15-12:
TYPE-B WAVEFORMS IN 1/3 MUX, 1/2 BIAS DRIVE
V2
COM0
V1
V0
COM2
V2
COM1
V1
COM1
V0
COM0
V2
COM2
V1
V0
V2
SEG0
V0
SEG0
SEG1
SEG2
V1
V2
SEG1
V1
V0
V2
V1
V0
COM0-SEG0
-V1
-V2
V2
V1
V0
COM0-SEG1
-V1
-V2
2 Frames
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 175
PIC18F85J90 FAMILY
FIGURE 15-13:
TYPE-A WAVEFORMS IN 1/3 MUX, 1/3 BIAS DRIVE
V3
V2
COM0
V1
V0
V3
COM2
V2
COM1
V1
COM1
V0
COM0
V3
V2
COM2
V1
V0
V3
V2
V1
V0
SEG0
SEG1
SEG2
SEG0
SEG2
V3
V2
SEG1
V1
V0
V3
V2
V1
V0
COM0-SEG0
-V1
-V2
-V3
V3
V2
V1
V0
COM0-SEG1
-V1
-V2
-V3
1 Frame
DS39770B-page 176
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 15-14:
TYPE-B WAVEFORMS IN 1/3 MUX, 1/3 BIAS DRIVE
V3
V2
COM0
V1
V0
V3
COM2
V2
COM1
V1
COM1
V0
COM0
V3
V2
COM2
V1
V0
V3
V2
SEG0
V0
SEG0
SEG1
SEG2
V1
V3
V2
SEG1
V1
V0
V3
V2
V1
V0
COM0-SEG0
-V1
-V2
-V3
V3
V2
V1
V0
COM0-SEG1
-V1
-V2
-V3
2 Frames
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 177
PIC18F85J90 FAMILY
FIGURE 15-15:
TYPE-A WAVEFORMS IN 1/4 MUX, 1/3 BIAS DRIVE
COM3
COM2
COM1
COM0
V3
V2
V1
V0
COM1
V3
V2
V1
V0
COM2
V3
V2
V1
V0
COM3
V3
V2
V1
V0
SEG0
V3
V2
V1
V0
SEG1
V3
V2
V1
V0
COM0-SEG0
V3
V2
V1
V0
-V1
-V2
-V3
COM0-SEG1
V3
V2
V1
V0
-V1
-V2
-V3
SEG0
SEG1
COM0
1 Frame
DS39770B-page 178
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 15-16:
TYPE-B WAVEFORMS IN 1/4 MUX, 1/3 BIAS DRIVE
COM3
COM2
COM1
COM0
V3
V2
V1
V0
COM1
V3
V2
V1
V0
COM2
V3
V2
V1
V0
COM3
V3
V2
V1
V0
SEG0
V3
V2
V1
V0
SEG1
V3
V2
V1
V0
COM0-SEG0
V3
V2
V1
V0
-V1
-V2
-V3
COM0-SEG1
V3
V2
V1
V0
-V1
-V2
-V3
SEG0
SEG1
COM0
2 Frames
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 179
PIC18F85J90 FAMILY
15.9
LCD Interrupts
When the LCD driver is running with Type-B waveforms, and the LMUX1:LMUX0 bits are not equal to
‘00’, there are some additional issues that must be
addressed. Since the DC voltage on the pixel takes two
frames to maintain zero volts, the pixel data must not
change between subsequent frames. If the pixel data
were allowed to change, the waveform for the odd
frames would not necessarily be the complement of the
waveform generated in the even frames and a DC
component would be introduced into the panel. Therefore, when using Type-B waveforms, the user must
synchronize the LCD pixel updates to occur within a
subframe after the frame interrupt.
The LCD timing generation provides an interrupt that
defines the LCD frame timing. This interrupt can be
used to coordinate the writing of the pixel data with the
start of a new frame. Writing pixel data at the frame
boundary allows a visually crisp transition of the image.
This interrupt can also be used to synchronize external
events to the LCD. For example, the interface to an
external segment driver can be synchronized for
segment data update to the LCD frame.
A new frame is defined to begin at the leading edge of
the COM0 common signal. The interrupt will be set
immediately after the LCD controller completes
accessing all pixel data required for a frame. This will
occur at a fixed interval before the frame boundary
(TFINT), as shown in Figure 15-17. The LCD controller
will begin to access data for the next frame within the
interval from the interrupt to when the controller begins
to access data after the interrupt (TFWR). New data
must be written within TFWR, as this is when the LCD
controller will begin to access the data for the next
frame.
FIGURE 15-17:
To correctly sequence writing while in Type-B, the
interrupt will only occur on complete phase intervals. If
the user attempts to write when the write is disabled,
the WERR (LCDCON<5>) bit is set.
Note:
The interrupt is not generated when the
Type-A waveform is selected and when the
Type-B with no multiplex (static) is
selected.
EXAMPLE WAVEFORMS AND INTERRUPT TIMING
IN QUARTER DUTY CYCLE DRIVE
LCD
Interrupt
Occurs
Controller Accesses
Next Frame Data
COM0
V3
V2
V1
V0
COM1
V3
V2
V1
V0
COM2
V3
V2
V1
V0
V3
V2
V1
V0
COM3
2 Frames
TFINT
Frame
Boundary
Frame
Boundary
TFWR
Frame
Boundary
TFWR = TFRAME/2 * (LMUX1:LMUX0 + 1) + TCY/2
TFINT = (TFWR/2 – (2 TCY + 40 ns)) → Minimum = 1.5(TFRAME/4) – (2 TCY + 40 ns)
(TFWR/2 – (1 TCY + 40 ns)) → Maximum = 1.5(TFRAME/4) – (1 TCY + 40 ns)
DS39770B-page 180
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
15.10 Operation During Sleep
The LCD module can operate during Sleep. The selection is controlled by the SLPEN bit (LCDCON<6>).
Setting the SLPEN bit allows the LCD module to go to
Sleep. Clearing the SLPEN bit allows the module to
continue to operate during Sleep.
If a SLEEP instruction is executed and SLPEN = 1, the
LCD module will cease all functions and go into a very
low-current consumption mode. The module will stop
operation immediately and drive the minimum LCD
voltage on both segment and common lines.
Figure 15-18 shows this operation.
To ensure that no DC component is introduced on the
panel, the SLEEP instruction should be executed immediately after a LCD frame boundary. The LCD interrupt
can be used to determine the frame boundary. See
Section 15.9 “LCD Interrupts” for the formulas to
calculate the delay.
If a SLEEP instruction is executed and SLPEN = 0, the
module will continue to display the current contents of
the LCDDATA registers. To allow the module to
continue operation while in Sleep, the clock source
must be either the Timer1 oscillator or one of the
FIGURE 15-18:
internal oscillators (either INTRC or INTOSC as the
default system clock). While in Sleep, the LCD data
cannot be changed. The LCD module current
consumption will not decrease in this mode; however,
the overall consumption of the device will be lower due
to shut down of the core and other peripheral functions.
If the system clock is selected and the module is not
configured for Sleep operation, the module will ignore
the SLPEN bit and stop operation immediately. The
minimum LCD voltage will then be driven onto the
segments and commons
15.10.1
USING THE LCD REGULATOR
DURING SLEEP
Applications that use the LCD regulator for bias
generation may not achieve the same degree of power
reductions in Sleep mode when compared to applications using Mode 3 (resistor ladder) biasing. This is
particularly true with Mode 0 operation, where the
charge pump is active.
If Modes 0, 1 or 2 are used for bias generation,
software contrast control will not be available.
SLEEP ENTRY/EXIT WHEN SLPEN = 1 OR CS1:CS0 = 00
V3
V2
V1
COM0
V0
V3
V2
V1
V0
COM1
V3
V2
V1
V0
COM2
V3
V2
V1
V0
SEG0
2 Frames
SLEEP Instruction Execution
© 2007 Microchip Technology Inc.
Preliminary
Wake-up
DS39770B-page 181
PIC18F85J90 FAMILY
15.11 Configuring the LCD Module
The following is the sequence of steps to configure the
LCD module.
1.
2.
3.
4.
5.
6.
7.
8.
Select the frame clock prescale using bits
LP3:LP0 (LCDPS<3:0>).
Configure the appropriate pins to function as
segment drivers using the LCDSEx registers.
Configure the appropriate pins as inputs using
TRISx registers.
Configure the LCD module for the following
using the LCDCON register:
•
Multiplex and Bias mode (LMUX1:LMUX0)
•
Timing source (CS1:CS0)
•
Sleep mode (SLPEN)
Write initial values to pixel data registers,
LCDDATA0 through LCDDATA23.
Configure the LCD Regulator:
a) If M2 or M3 bias configuration is to be used,
turn off the regulator by setting
CKSEL<1:0> (LCDREG<1:0>) to ‘00’. Set
or clear the CPEN bit (LCDREG<6>) to
select Mode 2 or Mode 3, as appropriate.
b) If M0 or M1 bias generation is to be used:
• Set the VBIAS level using the BIAS<2:0>
bits (LCDREG<5:3>).
• Set or clear the CPEN bit to enable or
disable the charge pump.
• Set or clear the MODE13 bit
(LCDREG<2>) to select the Bias mode.
• Select a regulator clock source using the
CKSEL<1:0> bits.
Clear LCD Interrupt Flag, LCDIF (PIR3<6>),
and if desired, enable the interrupt by setting the
LCDIE bit (PIE3<6>).
Enable the LCD module by setting the LCDEN
bit (LCDCON<7>).
DS39770B-page 182
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 15-6:
Name
REGISTERS ASSOCIATED WITH LCD OPERATION
Bit 7
Bit 6
Bit 5
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR3
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
54
PIE3
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
54
IPR3
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
54
INTCON
RCON
LCDDATA23(1)
GIE/GIEH PEIE/GIEL TMR0IE
Bit 4
IPEN
—
—
RI
TO
PD
POR
BOR
52
S47C3
S46C3
S45C3
S44C3
S43C3
S42C3
S41C3
S40C3
55
(1)
(1)
S35C3
S34C3
(1)
(1)
S32C3
55
S30C3
S29C3
S28C3
S27C3
S26C3
S25C3
S24C3
55
LCDDATA20
S23C3
S22C3
S21C3
S20C3
S19C3
S18C3
S17C3
S16C3
55
LCDDATA19
S15C3
S14C3
S13C3
S12C3
S11C3
S10C3
S09C3
S08C3
55
LCDDATA18
S07C3
S06C3
S05C3
S04C3
S03C3
S02C3
S01C3
S00C3
55
LCDDATA17(1)
S47C2
S46C2
S45C2
S44C2
S43C2
S42C2
S41C2
S40C2
55
LCDDATA16
S39C2(1)
S38C2(1)
S37C2(1)
S36C2(1)
S35C2(1)
S34C2(1)
S33C2(1)
S32C2
55
LCDDATA15
S31C2
S30C2
S29C2
S28C2
S27C2
S26C2
S25C2
S24C2
55
LCDDATA14
S23C2
S22C2
S21C2
S20C2
S19C2
S18C2
S17C2
S16C2
55
LCDDATA13
S15C2
S14C2
S13C2
S12C2
S11C2
S10C2
S09C2
S08C2
55
LCDDATA12
S07C2
S06C2
S05C2
S04C2
S03C2
S02C2
S01C2
S00C2
55
LCDDATA11(1)
S47C1
S46C1
S45C1
S44C1
S43C1
S42C1
S41C1
S40C1
55
LCDDATA10
S39C1(1)
S38C1(1)
S37C1(1)
S36C1(1)
S35C1(1)
S34C1(1)
S33C1(1)
S32C1
55
LCDDATA9
S31C1
S30C1
S29C1
S28C1
S27C1
S26C1
S25C1
S24C1
55
LCDDATA8
S23C1
S22C1
S21C1
S20C1
S19C1
S18C1
S17C1
S16C1
55
LCDDATA7
S15C1
S14C1
S13C1
S12C1
S11C1
S10C1
S09C1
S08C1
55
LCDDATA6
S07C1
S06C1
S05C1
S04C1
S03C1
S02C1
S01C1
S00C1
55
LCDDATA5(1)
S47C0
S46C0
S45C0
S44C0
S43C0
S42C0
S41C0
S40C0
55
S38C0(1)
S37C0(1)
S36C0(1)
S35C0(1)
S34C0(1)
S33C0(1)
(1)
S36C3
(1)
S31C3
S39C3
S37C3
(1)
LCDDATA21
LCDDATA22
S38C3
(1)
S33C3
S32C0
53
LCDDATA3
S31C0
S30C0
S29C0
S28C0
S27C0
S26C0
S25C0
S24C0
53
LCDDATA2
S23C0
S22C0
S21C0
S20C0
S19C0
S18C0
S17C0
S16C0
53
LCDDATA1
S15C0
S14C0
S13C0
S12C0
S11C0
S10C0
S09C0
S08C0
53
LCDDATA0
S07C0
S06C0
S05C0
S04C0
S03C0
S02C0
S01C0
S00C0
53
LCDSE5(1)
SE47
SE46
SE45
SE44
SE43
SE42
SE41
SE40
53
LCDSE4
SE39(1)
SE38(1)
SE37(1)
SE36(1)
SE35(1)
SE34(1)
SE33(1)
SE32
53
LCDSE3
SE31
SE30
SE29
SE28
SE27
SE26
SE25
SE24
53
LCDSE2
SE23
SE22
SE21
SE20
SE19
SE18
SE17
SE16
53
LCDSE1
SE15
SE14
SE13
SE12
SE11
SE10
SE09
SE08
53
LCDDATA4
S39C0
LCDSE0
SE07
SE06
SE05
SE04
SE03
SE02
SE01
SE00
53
LCDCON
LCDEN
SLPEN
WERR
—
CS1
CS0
LMUX1
LMUX0
53
WFT
BIASMD
LCDA
WA
LP3
LP2
LP1
LP0
53
—
CPEN
BIAS2
BIAS1
BIAS0
MODE13
CKSEL1
CKSEL0
LCDPS
LCDREG
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for LCD operation.
Note 1: These registers or individual bits are unimplemented on 64-pin devices.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 183
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 184
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.0
16.1
MASTER SYNCHRONOUS
SERIAL PORT (MSSP)
MODULE
16.3
SPI Mode
The SPI mode allows 8 bits of data to be synchronously
transmitted and received simultaneously. All four
modes of SPI are supported. To accomplish
communication, typically three pins are used:
Master SSP (MSSP) Module
Overview
The Master Synchronous Serial Port (MSSP) module is
a serial interface, useful for communicating with other
peripheral or microcontroller devices. These peripheral
devices may be serial EEPROMs, shift registers,
display drivers, A/D converters, etc. The MSSP module
can operate in one of two modes:
• Serial Data Out (SDO) – RC5/SDO
• Serial Data In (SDI) – RC4/SDI/SDA
• Serial Clock (SCK) – RC3/SCK/SCL
Additionally, a fourth pin may be used when in a Slave
mode of operation:
• Slave Select (SS) – RF7/SS
Figure 16-1 shows the block diagram of the MSSP
module when operating in SPI mode.
• Serial Peripheral Interface (SPI)
• Inter-Integrated Circuit (I2C™)
- Full Master mode
- Slave mode (with general address call)
FIGURE 16-1:
MSSP BLOCK DIAGRAM
(SPI MODE)
The I2C interface supports the following modes in
hardware:
Internal
Data Bus
• Master mode
• Multi-Master mode
• Slave mode
16.2
Read
Write
SSPBUF reg
Control Registers
Each MSSP module has three associated control
registers. These include a status register (SSPSTAT)
and two control registers (SSPCON1 and SSPCON2).
The use of these registers and their individual bits differ
significantly depending on whether the MSSP module
is operated in SPI or I2C mode.
Additional details are provided under the individual
sections.
SDI
SSPSR reg
SDO
SS
Shift
Clock
bit 0
SS Control
Enable
Edge
Select
2
Clock Select
SCK
SSPM3:SSPM0
SMP:CKE
4
TMR2 Output
2
2
(
Edge
Select
)
Prescaler TOSC
4, 16, 64
Data to TXx/RXx in SSPSR
TRIS bit
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 185
PIC18F85J90 FAMILY
16.3.1
REGISTERS
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to or read from.
Each MSSP module has four registers for SPI mode
operation. These are:
•
•
•
•
In receive operations, SSPSR and SSPBUF together
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
MSSP Control Register 1 (SSPCON1)
MSSP Status Register (SSPSTAT)
Serial Receive/Transmit Buffer Register (SSPBUF)
MSSP Shift Register (SSPSR) – Not directly
accessible
During
transmission,
the
SSPBUF
is
not
double-buffered. A write to SSPBUF will write to both
SSPBUF and SSPSR.
SSPCON1 and SSPSTAT are the control and status
registers in SPI mode operation. The SSPCON1
register is readable and writable. The lower 6 bits of
the SSPSTAT are read-only. The upper two bits of the
SSPSTAT are read/write.
REGISTER 16-1:
R/W-0
SMP
SSPSTAT: MSSP STATUS REGISTER (SPI MODE)
R/W-0
R-0
R-0
R-0
R-0
R0
R-0
(1)
D/A
P
S
R/W
UA
BF
CKE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
SMP: Sample bit
SPI Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
SPI Slave mode:
SMP must be cleared when SPI is used in Slave mode.
bit 6
CKE: SPI Clock Select bit(1)
1 = Transmit occurs on transition from active to Idle clock state
0 = Transmit occurs on transition from Idle to active clock state
bit 5
D/A: Data/Address bit
Used in I2C™ mode only.
bit 4
P: Stop bit
Used in I2C mode only. This bit is cleared when the MSSP module is disabled, SSPEN is cleared.
bit 3
S: Start bit
Used in I2C mode only.
bit 2
R/W: Read/Write Information bit
Used in I2C mode only.
bit 1
UA: Update Address bit
Used in I2C mode only.
bit 0
BF: Buffer Full Status bit (Receive mode only)
1 = Receive complete, SSPBUF is full
0 = Receive not complete, SSPBUF is empty
Note 1:
Polarity of clock state is set by the CKP bit (SSPCON1<4>).
DS39770B-page 186
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 16-2:
R/W-0
WCOL
SSPCON1: MSSP CONTROL REGISTER 1 (SPI MODE)
R/W-0
SSPOV
R/W-0
(1)
(2)
SSPEN
R/W-0
CKP
R/W-0
SSPM3
(3)
R/W-0
SSPM2
(3)
R/W-0
SSPM1
(3)
R/W-0
SSPM0(3)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
WCOL: Write Collision Detect bit (Transmit mode only)
1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in
software)
0 = No collision
bit 6
SSPOV: Receive Overflow Indicator bit(1)
SPI Slave mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user must read the
SSPBUF, even if only transmitting data, to avoid setting overflow (must be cleared in software).
0 = No overflow
bit 5
SSPEN: Master Synchronous Serial Port Enable bit(2)
1 = Enables serial port and configures SCK, SDO, SDI and SS as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
bit 4
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
bit 3-0
SSPM3:SSPM0: Master Synchronous Serial Port Mode Select bits(3)
0101 = SPI Slave mode, clock = SCK pin, SS pin control disabled, SS can be used as I/O pin
0100 = SPI Slave mode, clock = SCK pin, SS pin control enabled
0011 = SPI Master mode, clock = TMR2 output/2
0010 = SPI Master mode, clock = FOSC/64
0001 = SPI Master mode, clock = FOSC/16
0000 = SPI Master mode, clock = FOSC/4
Note 1:
2:
3:
In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by
writing to the SSPBUF register.
When enabled, these pins must be properly configured as input or output.
Bit combinations not specifically listed here are either reserved or implemented in I2C™ mode only.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 187
PIC18F85J90 FAMILY
16.3.2
OPERATION
When initializing the SPI, several options need to be
specified. This is done by programming the appropriate
control bits (SSPCON1<5:0> and SSPSTAT<7:6>).
These control bits allow the following to be specified:
•
•
•
•
Master mode (SCK is the clock output)
Slave mode (SCK is the clock input)
Clock Polarity (Idle state of SCK)
Data Input Sample Phase (middle or end of data
output time)
• Clock Edge (output data on rising/falling edge of
SCK)
• Clock Rate (Master mode only)
• Slave Select mode (Slave mode only)
Each MSSP consists of a transmit/receive shift register
(SSPSR) and a buffer register (SSPBUF). The SSPSR
shifts the data in and out of the device, MSb first. The
SSPBUF holds the data that was written to the SSPSR
until the received data is ready. Once the 8 bits of data
have been received, that byte is moved to the SSPBUF
register. Then, the Buffer Full detect bit, BF
(SSPSTAT<0>), and the interrupt flag bit, SSPIF, are
set. This double-buffering of the received data
(SSPBUF) allows the next byte to start reception before
EXAMPLE 16-1:
LOOP
BTFSS
BRA
MOVF
MOVWF
MOVF
MOVWF
DS39770B-page 188
reading the data that was just received. Any write to the
SSPBUF register during transmission/reception of data
will be ignored and the Write Collision detect bit, WCOL
(SSPCON1<7>), will be set. User software must clear
the WCOL bit so that it can be determined if the following write(s) to the SSPBUF register completed
successfully.
When the application software is expecting to receive
valid data, the SSPBUF should be read before the next
byte of data to transfer is written to the SSPBUF. The
Buffer Full bit, BF (SSPSTAT<0>), indicates when
SSPBUF has been loaded with the received data (transmission is complete). When the SSPBUF is read, the BF
bit is cleared. This data may be irrelevant if the SPI is
only a transmitter. Generally, the MSSP interrupt is used
to determine when the transmission/reception has completed. The SSPBUF must be read and/or written. If the
interrupt method is not going to be used, then software
polling can be done to ensure that a write collision does
not occur. Example 16-1 shows the loading of the
SSPBUF (SSPSR) for data transmission.
The SSPSR is not directly readable or writable and can
only be accessed by addressing the SSPBUF register.
Additionally, the SSPSTAT register indicates the
various status conditions.
LOADING THE SSPBUF (SSPSR) REGISTER
SSPSTAT, BF
LOOP
SSPBUF, W
RXDATA
TXDATA, W
SSPBUF
;Has data been received (transmit complete)?
;No
;WREG reg = contents of SSPBUF
;Save in user RAM, if data is meaningful
;W reg = contents of TXDATA
;New data to xmit
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.3.3
ENABLING SPI I/O
To enable the serial port, MSSP Enable bit, SSPEN
(SSPCON1<5>), must be set. To reset or reconfigure
SPI mode, clear the SSPEN bit, reinitialize the
SSPCON registers and then set the SSPEN bit. This
configures the SDI, SDO, SCK and SS pins as serial
port pins. For the pins to behave as the serial port function, some must have their data direction bits (in the
TRIS register) appropriately programmed as follows:
• SDI is automatically controlled by the SPI module
• SDO must have TRISC<5> bit cleared
• SCK (Master mode) must have TRISC<3> bit
cleared
• SCK (Slave mode) must have TRISC<3> bit set
• SS must have TRISF<7> bit set
Any serial port function that is not desired may be
overridden by programming the corresponding data
direction (TRIS) register to the opposite value.
16.3.4
OPEN-DRAIN OUTPUT OPTION
The drivers for the SDO output and SCK clock pins can
be optionally configured as open-drain outputs. This
feature allows the voltage level on the pin to be pulled
FIGURE 16-2:
to a higher level through an external pull-up resistor,
and allows the output to communicate with external
circuits without the need for additional level shifters.
The open-drain output option is controlled by the
SPIOD bit (TRISG<7>). Setting the bit configures both
pins for open-drain operation.
16.3.5
TYPICAL CONNECTION
Figure 16-2 shows a typical connection between two
microcontrollers. The master controller (Processor 1)
initiates the data transfer by sending the SCK signal.
Data is shifted out of both shift registers on their programmed clock edge and latched on the opposite edge
of the clock. Both processors should be programmed to
the same Clock Polarity (CKP), then both controllers
would send and receive data at the same time.
Whether the data is meaningful (or dummy data)
depends on the application software. This leads to
three scenarios for data transmission:
• Master sends data – Slave sends dummy data
• Master sends data – Slave sends data
• Master sends dummy data – Slave sends data
SPI MASTER/SLAVE CONNECTION
SPI Master SSPM3:SSPM0 = 00xx
SPI Slave SSPM3:SSPM0 = 010x
SDO
SDI
Serial Input Buffer
(SSPBUF)
SDI
Shift Register
(SSPSR)
MSb
Serial Input Buffer
(SSPBUF)
SDO
LSb
MSb
SCK
Serial Clock
PROCESSOR 1
© 2007 Microchip Technology Inc.
Shift Register
(SSPSR)
LSb
SCK
PROCESSOR 2
Preliminary
DS39770B-page 189
PIC18F85J90 FAMILY
16.3.6
MASTER MODE
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 2, Figure 16-2) will
broadcast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SDO output could be disabled (programmed as an input). The SSPSR register
will continue to shift in the signal present on the SDI pin
at the programmed clock rate. As each byte is
received, it will be loaded into the SSPBUF register as
if a normal received byte (interrupts and status bits
appropriately set). This could be useful in receiver
applications as a “Line Activity Monitor” mode.
FIGURE 16-3:
The clock polarity is selected by appropriately
programming the CKP bit (SSPCON1<4>). This, then,
would give waveforms for SPI communication as
shown in Figure 16-3, Figure 16-5 and Figure 16-6,
where the MSB is transmitted first. In Master mode, the
SPI clock rate (bit rate) is user-programmable to be one
of the following:
•
•
•
•
FOSC/4 (or TCY)
FOSC/16 (or 4 • TCY)
FOSC/64 (or 16 • TCY)
Timer2 output/2
This allows a maximum data rate (at 40 MHz) of
10.00 Mbps.
Figure 16-3 shows the waveforms for Master mode.
When the CKE bit is set, the SDO data is valid before
there is a clock edge on SCK. The change of the input
sample is shown based on the state of the SMP bit. The
time when the SSPBUF is loaded with the received
data is shown.
SPI MODE WAVEFORM (MASTER MODE)
Write to
SSPBUF
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
4 Clock
Modes
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
SDO
(CKE = 0)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
SDO
(CKE = 1)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
SDI
(SMP = 0)
bit 0
bit 7
Input
Sample
(SMP = 0)
SDI
(SMP = 1)
bit 0
bit 7
Input
Sample
(SMP = 1)
SSPIF
Next Q4 Cycle
after Q2↓
SSPSR to
SSPBUF
DS39770B-page 190
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.3.7
SLAVE MODE
In Slave mode, the data is transmitted and received as
the external clock pulses appear on SCK. When the
last bit is latched, the SSPIF interrupt flag bit is set.
Before enabling the module in SPI Slave mode, the
clock line must match the proper Idle state. The clock
line can be observed by reading the SCK pin. The Idle
state is determined by the CKP bit (SSPCON1<4>).
While in Slave mode, the external clock is supplied by
the external clock source on the SCK pin. This external
clock must meet the minimum high and low times as
specified in the electrical specifications.
While in Sleep mode, the slave can transmit/receive
data. When a byte is received, the device will wake-up
from Sleep.
16.3.8
SLAVE SELECT
SYNCHRONIZATION
The SS pin allows a Synchronous Slave mode. The SPI
must be in Slave mode with SS pin control enabled
(SSPCON1<3:0> = 04h). When the SS pin is low, transmission and reception are enabled and the SDO pin is
FIGURE 16-4:
driven. When the SS pin goes high, the SDO pin is no
longer driven, even if in the middle of a transmitted byte
and
becomes
a
floating
output.
External
pull-up/pull-down resistors may be desirable depending
on the application.
Note 1: When the SPI is in Slave mode with SS pin
control enabled (SSPCON1<3:0> = 0100),
the SPI module will reset if the SS pin is set
to VDD.
2: If the SPI is used in Slave mode with CKE
set, then the SS pin control must be
enabled.
When the SPI module resets, the bit counter is forced
to ‘0’. This can be done by either forcing the SS pin to
a high level or clearing the SSPEN bit.
To emulate two-wire communication, the SDO pin can
be connected to the SDI pin. When the SPI needs to
operate as a receiver, the SDO pin can be configured
as an input. This disables transmissions from the SDO.
The SDI can always be left as an input (SDI function)
since it cannot create a bus conflict.
SLAVE SYNCHRONIZATION WAVEFORM
SS
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
Write to
SSPBUF
SDO
SDI
(SMP = 0)
bit 7
bit 6
bit 7
bit 0
bit 0
bit 7
bit 7
Input
Sample
(SMP = 0)
SSPIF
Interrupt
Flag
Next Q4 Cycle
after Q2↓
SSPSR to
SSPBUF
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 191
PIC18F85J90 FAMILY
FIGURE 16-5:
SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 0)
SS
Optional
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
Write to
SSPBUF
SDO
SDI
(SMP = 0)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
bit 0
bit 7
Input
Sample
(SMP = 0)
SSPIF
Interrupt
Flag
Next Q4 Cycle
after Q2↓
SSPSR to
SSPBUF
FIGURE 16-6:
SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 1)
SS
Not Optional
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
Write to
SSPBUF
SDO
SDI
(SMP = 0)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
bit 0
bit 7
Input
Sample
(SMP = 0)
SSPIF
Interrupt
Flag
Next Q4 Cycle
after Q2↓
SSPSR to
SSPBUF
DS39770B-page 192
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.3.9
OPERATION IN POWER-MANAGED
MODES
In SPI Master mode, module clocks may be operating
at a different speed than when in Full Power mode; in
the case of Sleep mode, all clocks are halted.
In Idle modes, a clock is provided to the peripherals.
That clock should be from the primary clock source, the
secondary clock (Timer1 oscillator at 32.768 kHz) or
the INTRC source. See Section 2.3 “Clock Sources
and Oscillator Switching” for additional information.
In most cases, the speed that the master clocks SPI
data is not important; however, this should be
evaluated for each system.
If MSSP interrupts are enabled, they can wake the controller from Sleep mode, or one of the Idle modes, when
the master completes sending data. If an exit from
Sleep or Idle mode is not desired, MSSP interrupts
should be disabled.
If the Sleep mode is selected, all module clocks are
halted and the transmission/reception will remain in
that state until the devices wakes. After the device
returns to Run mode, the module will resume
transmitting and receiving data.
In SPI Slave mode, the SPI Transmit/Receive Shift
register operates asynchronously to the device. This
allows the device to be placed in any power-managed
TABLE 16-2:
Name
INTCON
mode and data to be shifted into the SPI
Transmit/Receive Shift register. When all 8 bits have
been received, the MSSP interrupt flag bit will be set
and if enabled, will wake the device.
16.3.10
EFFECTS OF A RESET
A Reset disables the MSSP module and terminates the
current transfer.
16.3.11
BUS MODE COMPATIBILITY
Table 16-1 shows the compatibility between the
standard SPI modes and the states of the CKP and
CKE control bits.
TABLE 16-1:
SPI BUS MODES
Control Bits State
Standard SPI Mode
Terminology
CKP
CKE
0, 0
0
1
0, 1
0
0
1, 0
1
1
1, 1
1
0
There is also an SMP bit which controls when the data
is sampled.
REGISTERS ASSOCIATED WITH SPI OPERATION
Bit 7
Bit 6
Bit 5
GIE/GIEH PEIE/GIEL TMR0IE
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
IPR1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
TRISC
TRISC7
TRISC6
TRISC5
TRISC4
TRISC3
TRISC2
TRISC1
TRISC0
54
TRISF
TRISF7
TRISF6
TRISF5
TRISF4
TRISF3
TRISF2
TRISF1
—
54
TRISG
SPIOD
CCP2OD
CCP1OD
TRISG4
TRISG3
TRISG2
TRISG1
TRISG0
54
SSPBUF
MSSP Receive Buffer/Transmit Register
52
SSPCON1
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
52
SSPSTAT
SMP
CKE
D/A
P
S
R/W
UA
BF
52
Legend: Shaded cells are not used by the MSSP module in SPI mode.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 193
PIC18F85J90 FAMILY
16.4
I2C Mode
16.4.1
The MSSP module in I 2C mode fully implements all
master and slave functions (including general call
support) and provides interrupts on Start and Stop bits
in hardware to determine a free bus (multi-master
function). The MSSP module implements the standard
mode specifications as well as 7-bit and 10-bit
addressing.
Two pins are used for data transfer:
• Serial clock (SCL) – RC3/SCK/SCL
• Serial data (SDA) – RC4/SDI/SDA
The user must configure these pins as inputs by setting
the TRISC<4:3> bits.
FIGURE 16-7:
MSSP BLOCK DIAGRAM
(I2C™ MODE)
Write
SSPBUF reg
SCL
SDA
Shift
Clock
LSb
MSSP Control Register 1 (SSPCON1)
MSSP Control Register 2 (SSPCON2)
MSSP Status Register (SSPSTAT)
Serial Receive/Transmit Buffer Register
(SSPBUF)
• MSSP Shift Register (SSPSR) – Not directly
accessible
• MSSP Address Register (SSPADD)
SSPCON1, SSPCON2 and SSPSTAT are the control
and status registers in I2C mode operation. The
SSPCON1 and SSPCON2 registers are readable and
writable. The lower 6 bits of the SSPSTAT are
read-only. The upper two bits of the SSPSTAT are
read/write.
Match Detect
SSPADD register holds the slave device address when
the MSSP is configured in I2C Slave mode. When the
MSSP is configured in Master mode, the lower seven
bits of SSPADD act as the Baud Rate Generator reload
value.
Addr Match
Address Mask
SSPADD reg
Start and
Stop bit Detect
DS39770B-page 194
•
•
•
•
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to or read from.
SSPSR reg
MSb
The MSSP module has six registers for I2C operation.
These are:
Many of the bits in SSPCON2 assume different
functions, depending on whether the module is operating in Master or Slave mode; bits <5:2> also assume
different names in Slave mode. The different aspects of
SSPCON2 are shown in Register 16-5 (for Master
mode) and Register 16-6 (Slave mode).
Internal
Data Bus
Read
REGISTERS
Set, Reset
S, P bits
(SSPSTAT reg)
In receive operations, SSPSR and SSPBUF together
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
During
transmission,
the
SSPBUF
is
not
double-buffered. A write to SSPBUF will write to both
SSPBUF and SSPSR.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 16-3:
R/W-0
SSPSTAT: MSSP STATUS REGISTER (I2C™ MODE)
R/W-0
SMP
CKE
R-0
R-0
R-0
R-0
R0
R-0
D/A
(1)
(1)
R/W
UA
BF
P
S
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
SMP: Slew Rate Control bit
In Master or Slave mode:
1 = Slew rate control disabled for Standard Speed mode (100 kHz and 1 MHz)
0 = Slew rate control enabled for High-Speed mode (400 kHz)
bit 6
CKE: SMBus Select bit
In Master or Slave mode:
1 = Enable SMBus specific inputs
0 = Disable SMBus specific inputs
bit 5
D/A: Data/Address bit
In Master mode:
Reserved.
In Slave mode:
1 = Indicates that the last byte received or transmitted was data
0 = Indicates that the last byte received or transmitted was address
bit 4
P: Stop bit(1)
1 = Indicates that a Stop bit has been detected last
0 = Stop bit was not detected last
bit 3
S: Start bit(1)
1 = Indicates that a Start bit has been detected last
0 = Start bit was not detected last
bit 2
R/W: Read/Write Information bit (I2C mode only)
In Slave mode:(2)
1 = Read
0 = Write
In Master mode:(3)
1 = Transmit is in progress
0 = Transmit is not in progress
bit 1
UA: Update Address bit (10-Bit Slave mode only)
1 = Indicates that the user needs to update the address in the SSPADD register
0 = Address does not need to be updated
bit 0
BF: Buffer Full Status bit
In Transmit mode:
1 = SSPBUF is full
0 = SSPBUF is empty
In Receive mode:
1 = SSPBUF is full (does not include the ACK and Stop bits)
0 = SSPBUF is empty (does not include the ACK and Stop bits)
Note 1:
2:
3:
This bit is cleared on Reset and when SSPEN is cleared.
This bit holds the R/W bit information following the last address match. This bit is only valid from the
address match to the next Start bit, Stop bit or not ACK bit.
ORing this bit with SEN, RSEN, PEN, RCEN or ACKEN will indicate if the MSSP is in Active mode.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 195
PIC18F85J90 FAMILY
REGISTER 16-4:
R/W-0
WCOL
SSPCON1: MSSP CONTROL REGISTER 1 (I2C™ MODE)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SSPOV
SSPEN(1)
CKP
SSPM3
SSPM2
SSPM1
SSPM0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
WCOL: Write Collision Detect bit
In Master Transmit mode:
1 = A write to the SSPBUF register was attempted while the I2C conditions were not valid for a
transmission to be started (must be cleared in software)
0 = No collision
In Slave Transmit mode:
1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in
software)
0 = No collision
In Receive mode (Master or Slave modes):
This is a “don’t care” bit.
bit 6
SSPOV: Receive Overflow Indicator bit
In Receive mode:
1 = A byte is received while the SSPBUF register is still holding the previous byte (must be cleared in
software)
0 = No overflow
In Transmit mode:
This is a “don’t care” bit in Transmit mode.
bit 5
SSPEN: Master Synchronous Serial Port Enable bit(1)
1 = Enables the serial port and configures the SDA and SCL pins as the serial port pins
0 = Disables serial port and configures these pins as I/O port pins
bit 4
CKP: SCK Release Control bit
In Slave mode:
1 = Release clock
0 = Holds clock low (clock stretch), used to ensure data setup time
In Master mode:
Unused in this mode.
bit 3-0
SSPM3:SSPM0: Synchronous Serial Port Mode Select bits
1111 = I2C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
1110 = I2C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
1011 = I2C Firmware Controlled Master mode (slave Idle)
1000 = I2C Master mode, clock = FOSC/(4 * (SSPADD + 1))
0111 = I2C Slave mode, 10-bit address
0110 = I2C Slave mode, 7-bit address
Bit combinations not specifically listed here are either reserved or implemented in SPI mode only.
Note 1:
When enabled, the SDA and SCL pins must be configured as inputs.
DS39770B-page 196
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 16-5:
SSPCON2: MSSP CONTROL REGISTER 2 (I2C™ MASTER MODE)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
GCEN
ACKSTAT
ACKDT(1)
ACKEN(2)
RCEN(2)
PEN(2)
RSEN(2)
SEN(2)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
GCEN: General Call Enable bit
Unused in Master mode.
bit 6
ACKSTAT: Acknowledge Status bit (Master Transmit mode only)
1 = Acknowledge was not received from slave
0 = Acknowledge was received from slave
bit 5
ACKDT: Acknowledge Data bit (Master Receive mode only)(1)
1 = Not Acknowledge
0 = Acknowledge
bit 4
ACKEN: Acknowledge Sequence Enable bit(2)
1 = Initiate Acknowledge sequence on SDA and SCL pins and transmit ACKDT data bit. Automatically
cleared by hardware.
0 = Acknowledge sequence Idle
bit 3
RCEN: Receive Enable bit (Master Receive mode only)(2)
1 = Enables Receive mode for I2C
0 = Receive Idle
bit 2
PEN: Stop Condition Enable bit(2)
1 = Initiate Stop condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Stop condition Idle
bit 1
RSEN: Repeated Start Condition Enable bit(2)
1 = Initiate Repeated Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Repeated Start condition Idle
bit 0
SEN: Start Condition Enable bit(2)
1 = Initiate Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Start condition Idle
Note 1:
2:
Value that will be transmitted when the user initiates an Acknowledge sequence at the end of a receive.
If the I2C module is active, these bits may not be set (no spooling) and the SSPBUF may not be written (or
writes to the SSPBUF are disabled).
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 197
PIC18F85J90 FAMILY
REGISTER 16-6:
SSPCON2: MSSP CONTROL REGISTER 2 (I2C™ SLAVE MODE)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
GCEN
ACKSTAT
ADMSK5
ADMSK4
ADMSK3
ADMSK2
ADMSK1
SEN(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
GCEN: General Call Enable bit
1 = Enable interrupt when a general call address (0000h) is received in the SSPSR
0 = General call address disabled
bit 6
ACKSTAT: Acknowledge Status bit
Unused in Slave mode.
bit 5-2
ADMSK5:ADMSK2: Slave Address Mask Select bits
1 = Masking of corresponding bits of SSPADD enabled
0 = Masking of corresponding bits of SSPADD disabled
bit 1
ADMSK1: Slave Address Least Significant bit(s) Mask Select bit
In 7-Bit Address mode:
1 = Masking of SSPADD<1> only enabled
0 = Masking of SSPADD<1> only disabled
In 10-Bit Address mode:
1 = Masking of SSPADD<1:0> enabled
0 = Masking of SSPADD<1:0> disabled
bit 0
SEN: Stretch Enable bit(1)
1 = Clock stretching is enabled for both slave transmit and slave receive (stretch enabled)
0 = Clock stretching is disabled
Note 1:
If the I2C module is active, this bit may not be set (no spooling) and the SSPBUF may not be written (or
writes to the SSPBUF are disabled).
DS39770B-page 198
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.4.2
OPERATION
The MSSP module functions are enabled by setting the
MSSP Enable bit, SSPEN (SSPCON1<5>).
The SSPCON1 register allows control of the I 2C
operation. Four mode selection bits (SSPCON1<3:0>)
allow one of the following I 2C modes to be selected:
2
• I C Master mode,
clock = (FOSC/4) x (SSPADD + 1)
• I 2C Slave mode (7-bit address)
• I 2C Slave mode (10-bit address)
• I 2C Slave mode (7-bit address) with Start and
Stop bit interrupts enabled
• I 2C Slave mode (10-bit address) with Start and
Stop bit interrupts enabled
• I 2C Firmware Controlled Master mode,
slave is Idle
1.
SLAVE MODE
In Slave mode, the SCL and SDA pins must be
configured as inputs (TRISC<4:3> set). The MSSP
module will override the input state with the output data
when required (slave-transmitter).
The I 2C Slave mode hardware will always generate an
interrupt on an exact address match. In addition,
address masking will also allow the hardware to generate an interrupt for more than one address (up to 31 in
7-bit addressing and up to 63 in 10-bit addressing).
Through the mode select bits, the user can also choose
to interrupt on Start and Stop bits.
When an address is matched, or the data transfer after
an address match is received, the hardware automatically will generate the Acknowledge (ACK) pulse
and load the SSPBUF register with the received value
currently in the SSPSR register.
Any combination of the following conditions will cause
the MSSP module not to give this ACK pulse:
• The Buffer Full bit, BF (SSPSTAT<0>), was set
before the transfer was received.
• The overflow bit, SSPOV (SSPCON1<6>), was
set before the transfer was received.
2.
3.
4.
Addressing
The SSPSR register value is loaded into the
SSPBUF register.
The Buffer Full bit, BF, is set.
An ACK pulse is generated.
The MSSP Interrupt Flag bit, SSPIF, is set (and
interrupt is generated, if enabled) on the falling
edge of the ninth SCL pulse.
In 10-Bit Address mode, two address bytes need to be
received by the slave. The five Most Significant bits
(MSbs) of the first address byte specify if this is a 10-bit
address. Bit R/W (SSPSTAT<2>) must specify a write so
the slave device will receive the second address byte.
For a 10-bit address, the first byte would equal ‘11110
A9 A8 0’, where ‘A9’ and ‘A8’ are the two MSbs of the
address. The sequence of events for 10-bit address is as
follows, with steps 7 through 9 for the slave-transmitter:
1.
2.
3.
4.
5.
6.
In this case, the SSPSR register value is not loaded
into the SSPBUF, but bit SSPIF is set. The BF bit is
cleared by reading the SSPBUF register, while bit
SSPOV is cleared through software.
© 2007 Microchip Technology Inc.
16.4.3.1
Once the MSSP module has been enabled, it waits for a
Start condition to occur. Following the Start condition, the
8 bits are shifted into the SSPSR register. All incoming
bits are sampled with the rising edge of the clock (SCL)
line. The value of register SSPSR<7:1> is compared to
the value of the SSPADD register. The address is compared on the falling edge of the eighth clock (SCL) pulse.
If the addresses match and the BF and SSPOV bits are
clear, the following events occur:
Selection of any I 2C mode, with the SSPEN bit set,
forces the SCL and SDA pins to be open-drain,
provided these pins are programmed to inputs by
setting the appropriate TRISC or TRISD bits. To ensure
proper operation of the module, pull-up resistors must
be provided externally to the SCL and SDA pins.
16.4.3
The SCL clock input must have a minimum high and
low for proper operation. The high and low times of the
I2C specification, as well as the requirement of the
MSSP module, are shown in timing parameter 100 and
parameter 101.
7.
8.
9.
Preliminary
Receive first (high) byte of address (bits SSPIF,
BF and UA (SSPSTAT<1>) are set).
Update the SSPADD register with second (low)
byte of address (clears bit UA and releases the
SCL line).
Read the SSPBUF register (clears bit BF) and
clear flag bit, SSPIF.
Receive second (low) byte of address (SSPIF,
BF and UA bits are set).
Update the SSPADD register with the first (high)
byte of address. If match releases SCL line, this
will clear UA bit.
Read the SSPBUF register (clears bit BF) and
clear flag bit, SSPIF.
Receive Repeated Start condition.
Receive first (high) byte of address (SSPIF and
BF bits are set).
Read the SSPBUF register (clears BF bit) and
clear flag bit, SSPIF.
DS39770B-page 199
PIC18F85J90 FAMILY
16.4.3.2
Address Masking
Masking an address bit causes that bit to become a
“don’t care”. When one address bit is masked, two
addresses will be Acknowledged and cause an
interrupt. It is possible to mask more than one address
bit at a time, which makes it possible to Acknowledge
up to 31 addresses in 7-bit mode and up to
63 addresses in 10-bit mode (see Example 16-2).
The I2C Slave behaves the same way whether address
masking is used or not. However, when address
masking is used, the I2C slave can Acknowledge
multiple addresses and cause interrupts. When this
occurs, it is necessary to determine which address
caused the interrupt by checking SSPBUF.
In 10-Bit Address mode, ADMSK<5:2> bits mask the
corresponding address bits in the SSPADD register. In
addition, ADMSK1 simultaneously masks the two LSbs
of the address (SSPADD<1:0>). For any ADMSK bits
that are active (ADMSK<n> = 1), the corresponding
address bit is ignored (SSPADD<n> = x). Also note
that although in 10-Bit Addressing mode, the upper
address bits reuse part of the SSPADD register bits, the
address mask bits do not interact with those bits. They
only affect the lower address bits.
Note 1: ADMSK1 masks the two Least Significant
bits of the address.
In 7-Bit Address mode, address mask bits, ADMSK<5:1>
(SSPCON<5:1>), mask the corresponding address bits
in the SSPADD register. For any ADMSK bits that are set
(ADMSK<n> = 1), the corresponding address bit is
ignored (SSPADD<n> = x). For the module to issue an
address Acknowledge, it is sufficient to match only on
addresses that do not have an active address mask.
EXAMPLE 16-2:
2: The two Most Significant bits of the
address are not affected by address
masking.
ADDRESS MASKING EXAMPLES
7-Bit Addressing:
SSPADD<7:1> = A0h (1010000) (SSPADD<0> is assumed to be ‘0’)
ADMSK<5:1>
= 00111
Addresses Acknowledged: A0h, A2h, A4h, A6h, A8h, AAh, ACh, AEh
10-Bit Addressing:
SSPADD<7:0> = A0h (10100000) (the two MSbs of the address are ignored in this example, since they are
not affected by masking)
ADMSK<5:1>
= 00111
Addresses Acknowledged: A0h, A1h, A2h, A3h, A4h, A5h, A6h, A7h, A8h, A9h, AAh, ABh, ACh, ADh, AEh, AFh
DS39770B-page 200
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.4.3.3
Reception
16.4.3.4
When the R/W bit of the address byte is clear and an
address match occurs, the R/W bit of the SSPSTAT
register is cleared. The received address is loaded into
the SSPBUF register and the SDA line is held low
(ACK).
When the address byte overflow condition exists, then
the no Acknowledge (ACK) pulse is given. An overflow
condition is defined as either bit, BF (SSPSTAT<0>), is
set or bit, SSPOV (SSPCON1<6>), is set.
An MSSP interrupt is generated for each data transfer
byte. The interrupt flag bit, SSPIF, must be cleared in
software. The SSPSTAT register is used to determine
the status of the byte.
If SEN is enabled (SSPCON2<0> = 1), SCK/SCL will
be held low (clock stretch) following each data
transfer. The clock must be released by setting bit,
CKP (SSPCON1<4>). See Section 16.4.4 “Clock
Stretching” for more details.
Transmission
When the R/W bit of the incoming address byte is set
and an address match occurs, the R/W bit of the
SSPSTAT register is set. The received address is
loaded into the SSPBUF register. The ACK pulse will
be sent on the ninth bit and pin RC3 is held low, regardless of SEN (see Section 16.4.4 “Clock Stretching”
for more details). By stretching the clock, the master
will be unable to assert another clock pulse until the
slave is done preparing the transmit data. The transmit
data must be loaded into the SSPBUF register which
also loads the SSPSR register. Then, pin RC3 should
be enabled by setting bit, CKP (SSPCON1<4>). The
eight data bits are shifted out on the falling edge of the
SCL input. This ensures that the SDA signal is valid
during the SCL high time (Figure 16-10).
The ACK pulse from the master-receiver is latched on
the rising edge of the ninth SCL input pulse. If the SDA
line is high (not ACK), then the data transfer is
complete. In this case, when the ACK is latched by the
slave, the slave logic is reset (resets SSPSTAT
register) and the slave monitors for another occurrence
of the Start bit. If the SDA line was low (ACK), the next
transmit data must be loaded into the SSPBUF register.
Again, pin RC3 must be enabled by setting bit, CKP.
An MSSP interrupt is generated for each data transfer
byte. The SSPIF bit must be cleared in software and
the SSPSTAT register is used to determine the status
of the byte. The SSPIF bit is set on the falling edge of
the ninth clock pulse.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 201
DS39770B-page 202
Preliminary
CKP
2
A6
3
A5
4
A4
5
A3
6
A2
(CKP does not reset to ‘0’ when SEN = 0)
SSPOV (SSPCON1<6>)
BF (SSPSTAT<0>)
SSPIF (PIR1<3>)
1
SCL
S
A7
7
A1
8
9
ACK
R/W = 0
1
D7
3
4
D4
5
D3
Receiving Data
D5
Cleared in software
SSPBUF is read
2
D6
6
D2
7
D1
8
D0
9
ACK
1
D7
2
D6
3
4
D4
5
D3
Receiving Data
D5
6
D2
7
D1
8
D0
Bus master
terminates
transfer
P
SSPOV is set
because SSPBUF is
still full. ACK is not sent.
9
ACK
FIGURE 16-8:
SDA
Receiving Address
PIC18F85J90 FAMILY
I2C™ SLAVE MODE TIMING WITH SEN = 0 (RECEPTION, 7-BIT ADDRESS)
© 2007 Microchip Technology Inc.
© 2007 Microchip Technology Inc.
Preliminary
Note
CKP
2
A6
3
4
X
5
A3
Receiving Address
A5
6
X
1
3
4
D4
5
D3
Receiving Data
D5
Cleared in software
SSPBUF is read
2
D6
6
D2
7
D1
8
D0
In this example, an address equal to A7.A6.A5.X.A3.X.X will be Acknowledged and cause an interrupt.
9
D7
x = Don’t care (i.e., address bit can be either a ‘1’ or a ‘0’).
8
ACK
R/W = 0
2:
7
X
1:
(CKP does not reset to ‘0’ when SEN = 0)
SSPOV (SSPCON1<6>)
BF (SSPSTAT<0>)
SSPIF (PIR1<3>)
1
SCL
S
A7
9
ACK
1
D7
2
D6
3
4
D4
5
D3
Receiving Data
D5
6
D2
7
D1
8
D0
Bus master
terminates
transfer
P
SSPOV is set
because SSPBUF is
still full. ACK is not sent.
9
ACK
FIGURE 16-9:
SDA
PIC18F85J90 FAMILY
I2C™ SLAVE MODE TIMING WITH SEN = 0 AND ADMSK<5:1> = 01011
(RECEPTION, 7-BIT ADDRESS)
DS39770B-page 203
DS39770B-page 204
Preliminary
CKP
BF (SSPSTAT<0>)
SSPIF (PIR1<3>)
S
2
A6
Data in
sampled
1
A7
3
4
A4
5
A3
6
A2
Receiving Address
A5
7
A1
8
R/W = 0
9
ACK
SCL held low
while CPU
responds to SSPIF
1
D7
3
D5
4
5
D3
CKP is set in software
SSPBUF is written in software
6
D2
Transmitting Data
D4
Cleared in software
2
D6
7
D1
9
ACK
From SSPIF ISR
8
D0
1
D7
4
D4
5
D3
6
D2
CKP is set in software
7
8
D0
9
ACK
From SSPIF ISR
D1
Transmitting Data
Cleared in software
3
D5
SSPBUF is written in software
2
D6
P
FIGURE 16-10:
SCL
SDA
PIC18F85J90 FAMILY
I2C™ SLAVE MODE TIMING (TRANSMISSION, 7-BIT ADDRESS)
© 2007 Microchip Technology Inc.
© 2007 Microchip Technology Inc.
Preliminary
4
1
5
0
7
A8
UA is set indicating that
the SSPADD needs to be
updated
SSPBUF is written with
contents of SSPSR
6
A9
8
9
(CKP does not reset to ‘0’ when SEN = 0)
UA (SSPSTAT<1>)
CKP
3
1
Cleared in software
2
1
SSPOV (SSPCON1<6>)
BF (SSPSTAT<0>)
SSPIF (PIR1<3>)
1
SCL
S
1
ACK
R/W = 0
A7
2
4
A4
5
A3
6
A2
8
A0
UA is set indicating that
SSPADD needs to be
updated
Cleared by hardware
when SSPADD is updated
with low byte of address
7
A1
Cleared in software
3
A5
Dummy read of SSPBUF
to clear BF flag
1
A6
Receive Second Byte of Address
9
ACK
1
D7
4
5
6
Cleared in software
3
7
D5 D4 D3 D2 D1
Receive Data Byte
Cleared by hardware when
SSPADD is updated with high
byte of address
2
D6
Clock is held low until
update of SSPADD has
taken place
8
9
1
2
4
5
6
D3 D2
Cleared in software
3
D5 D4
Receive Data Byte
D0 ACK D7 D6
7
8
D1 D0
9
P
Bus master
terminates
transfer
SSPOV is set
because SSPBUF is
still full. ACK is not sent.
ACK
FIGURE 16-11:
SDA
Receive First Byte of Address
Clock is held low until
update of SSPADD has
taken place
PIC18F85J90 FAMILY
I2C™ SLAVE MODE TIMING WITH SEN = 0 (RECEPTION, 10-BIT ADDRESS)
DS39770B-page 205
DS39770B-page 206
2
1
Preliminary
Note
4
1
5
0
7
A8
UA is set indicating that
the SSPADD needs to be
updated
SSPBUF is written with
contents of SSPSR
6
A9
8
9
ACK
2
X
4
5
A3
6
A2
Cleared in software
3
A5
4
5
6
7
8
9
1
2
4
5
6
D3 D2
Cleared in software
3
D5 D4
Receive Data Byte
D1 D0 ACK D7 D6
Cleared in software
3
D2
Cleared by hardware when
SSPADD is updated with high
byte of address
2
D6 D5 D4 D3
Note that the Most Significant bits of the address are not affected by the bit masking.
1
D7
3:
9
ACK
x = Don’t care (i.e., address bit can be either a ‘1’ or a ‘0’).
8
X
In this example, an address equal to A9.A8.A7.A6.A5.X.A3.A2.X.X will be Acknowledged and cause an interrupt.
UA is set indicating that
SSPADD needs to be
updated
7
X
Cleared by hardware
when SSPADD is updated
with low byte of address
Dummy read of SSPBUF
to clear BF flag
1
A6
Receive Data Byte
1:
A7
Receive Second Byte of Address
2:
(CKP does not reset to ‘0’ when SEN = 0)
UA (SSPSTAT<1>)
SSPOV (SSPCON1<6>)
CKP
3
1
Cleared in software
BF (SSPSTAT<0>)
SSPIF (PIR1<3>)
1
SCL
S
1
R/W = 0
Clock is held low until
update of SSPADD has
taken place
7
8
D1 D0
9
P
Bus master
terminates
transfer
SSPOV is set
because SSPBUF is
still full. ACK is not sent.
ACK
FIGURE 16-12:
SDA
Receive First Byte of Address
Clock is held low until
update of SSPADD has
taken place
PIC18F85J90 FAMILY
I2C™ SLAVE MODE TIMING WITH SEN = 0 AND ADMSK<5:1> = 01001
(RECEPTION, 10-BIT ADDRESS)
© 2007 Microchip Technology Inc.
© 2007 Microchip Technology Inc.
Preliminary
2
1
CKP (SSPCON1<4>)
UA (SSPSTAT<1>)
BF (SSPSTAT<0>)
SSPIF (PIR1<3>)
1
SCL
S
1
4
1
5
0
6
7
A9 A8
8
UA is set indicating that
the SSPADD needs to be
updated
SSPBUF is written with
contents of SSPSR
3
1
9
ACK
R/W = 0
1
3
4
5
Cleared in software
2
7
UA is set indicating that
SSPADD needs to be
updated
Cleared by hardware when
SSPADD is updated with low
byte of address
6
8
A6 A5 A4 A3 A2 A1 A0
Receive Second Byte of Address
Dummy read of SSPBUF
to clear BF flag
A7
9
ACK
2
3
1
4
1
Cleared in software
1
1
5
0
6
8
9
ACK
R/W = 1
1
2
4
5
6
Cleared in software
3
CKP is set in software
9
P
Completion of
data transmission
clears BF flag
8
ACK
Bus master
terminates
transfer
CKP is automatically cleared in hardware, holding SCL low
7
D7 D6 D5 D4 D3 D2 D1 D0
Transmitting Data Byte
Clock is held low until
CKP is set to ‘1’
Write of SSPBUF
BF flag is clear
initiates transmit
at the end of the
third address sequence
7
A9 A8
Cleared by hardware when
SSPADD is updated with high
byte of address.
Dummy read of SSPBUF
to clear BF flag
Sr
1
Receive First Byte of Address
Clock is held low until
update of SSPADD has
taken place
FIGURE 16-13:
SDA
Receive First Byte of Address
Clock is held low until
update of SSPADD has
taken place
PIC18F85J90 FAMILY
I2C™ SLAVE MODE TIMING (TRANSMISSION, 10-BIT ADDRESS)
DS39770B-page 207
PIC18F85J90 FAMILY
16.4.4
CLOCK STRETCHING
16.4.4.3
Both 7-Bit and 10-Bit Slave modes implement
automatic clock stretching during a transmit sequence.
The SEN bit (SSPCON2<0>) allows clock stretching to
be enabled during receives. Setting SEN will cause
the SCL pin to be held low at the end of each data
receive sequence.
16.4.4.1
Clock Stretching for 7-Bit Slave
Receive Mode (SEN = 1)
In 7-Bit Slave Receive mode, on the falling edge of the
ninth clock at the end of the ACK sequence, if the BF
bit is set, the CKP bit in the SSPCON1 register is
automatically cleared, forcing the SCL output to be
held low. The CKP being cleared to ‘0’ will assert the
SCL line low. The CKP bit must be set in the user’s
ISR before reception is allowed to continue. By holding
the SCL line low, the user has time to service the ISR
and read the contents of the SSPBUF before the
master device can initiate another receive sequence.
This will prevent buffer overruns from occurring (see
Figure 16-15).
Note 1: If the user reads the contents of the
SSPBUF before the falling edge of the
ninth clock, thus clearing the BF bit, the
CKP bit will not be cleared and clock
stretching will not occur.
2: The CKP bit can be set in software
regardless of the state of the BF bit. The
user should be careful to clear the BF bit
in the ISR before the next receive
sequence in order to prevent an overflow
condition.
16.4.4.2
Clock Stretching for 7-Bit Slave
Transmit Mode
The 7-Bit Slave Transmit mode implements clock
stretching by clearing the CKP bit after the falling edge
of the ninth clock if the BF bit is clear. This occurs
regardless of the state of the SEN bit.
The user’s ISR must set the CKP bit before transmission is allowed to continue. By holding the SCL line
low, the user has time to service the ISR and load the
contents of the SSPBUF before the master device can
initiate another transmit sequence (see Figure 16-10).
Note 1: If the user loads the contents of SSPBUF,
setting the BF bit before the falling edge of
the ninth clock, the CKP bit will not be
cleared and clock stretching will not occur.
2: The CKP bit can be set in software
regardless of the state of the BF bit.
16.4.4.4
Clock Stretching for 10-Bit Slave
Transmit Mode
In 10-Bit Slave Transmit mode, clock stretching is controlled during the first two address sequences by the
state of the UA bit, just as it is in 10-Bit Slave Receive
mode. The first two addresses are followed by a third
address sequence which contains the high-order bits
of the 10-bit address and the R/W bit set to ‘1’. After
the third address sequence is performed, the UA bit is
not set, the module is now configured in Transmit
mode and clock stretching is controlled by the BF flag
as in 7-Bit Slave Transmit mode (see Figure 16-13).
Clock Stretching for 10-Bit Slave
Receive Mode (SEN = 1)
In 10-Bit Slave Receive mode, during the address
sequence, clock stretching automatically takes place
but CKP is not cleared. During this time, if the UA bit is
set after the ninth clock, clock stretching is initiated.
The UA bit is set after receiving the upper byte of the
10-bit address and following the receive of the second
byte of the 10-bit address with the R/W bit cleared to
‘0’. The release of the clock line occurs upon updating
SSPADD. Clock stretching will occur on each data
receive sequence as described in 7-bit mode.
Note:
If the user polls the UA bit and clears it by
updating the SSPADD register before the
falling edge of the ninth clock occurs and if
the user hasn’t cleared the BF bit by reading the SSPBUF register before that time,
then the CKP bit will still NOT be asserted
low. Clock stretching on the basis of the
state of the BF bit only occurs during a
data sequence, not an address sequence.
DS39770B-page 208
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.4.4.5
Clock Synchronization and
the CKP bit
When the CKP bit is cleared, the SCL output is forced
to ‘0’. However, clearing the CKP bit will not assert the
SCL output low until the SCL output is already sampled low. Therefore, the CKP bit will not assert the
SCL line until an external I2C master device has
FIGURE 16-14:
already asserted the SCL line. The SCL output will
remain low until the CKP bit is set and all other
devices on the I2C bus have deasserted SCL. This
ensures that a write to the CKP bit will not violate the
minimum high time requirement for SCL (see
Figure 16-14).
CLOCK SYNCHRONIZATION TIMING
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
SDA
DX
DX – 1
SCL
CKP
Master device
asserts clock
Master device
deasserts clock
WR
SSPCON
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 209
DS39770B-page 210
Preliminary
CKP
SSPOV (SSPCON1<6>)
BF (SSPSTAT<0>)
SSPIF (PIR1<3>)
1
SCL
S
A7
2
A6
3
4
A4
5
A3
6
A2
Receiving Address
A5
7
A1
8
9
ACK
R/W = 0
3
4
D4
5
D3
Receiving Data
D5
Cleared in software
2
D6
If BF is cleared
prior to the falling
edge of the 9th clock,
CKP will not be reset
to ‘0’ and no clock
stretching will occur
SSPBUF is read
1
D7
6
D2
7
D1
9
ACK
1
D7
BF is set after falling
edge of the 9th clock,
CKP is reset to ‘0’ and
clock stretching occurs
8
D0
3
4
D4
5
D3
Receiving Data
D5
CKP
written
to ‘1’ in
software
2
D6
Clock is held low until
CKP is set to ‘1’
6
D2
7
D1
8
D0
Bus master
terminates
transfer
P
SSPOV is set
because SSPBUF is
still full. ACK is not sent.
9
ACK
Clock is not held low
because ACK = 1
FIGURE 16-15:
SDA
Clock is not held low
because buffer full bit is
clear prior to falling edge
of 9th clock
PIC18F85J90 FAMILY
I2C™ SLAVE MODE TIMING WITH SEN = 1 (RECEPTION, 7-BIT ADDRESS)
© 2007 Microchip Technology Inc.
© 2007 Microchip Technology Inc.
2
1
Preliminary
UA (SSPSTAT<1>)
SSPOV (SSPCON1<6>)
CKP
3
1
4
1
5
0
6
7
A9 A8
8
UA is set indicating that
the SSPADD needs to be
updated
SSPBUF is written with
contents of SSPSR
Cleared in software
BF (SSPSTAT<0>)
SSPIF (PIR1<3>)
1
SCL
S
1
9
ACK
R/W = 0
A7
2
4
A4
5
A3
6
A2
Cleared in software
3
A5
7
A1
8
A0
Note: An update of the SSPADD
register before the falling
edge of the ninth clock will
have no effect on UA and
UA will remain set.
UA is set indicating that
SSPADD needs to be
updated
Cleared by hardware when
SSPADD is updated with low
byte of address after falling edge
of ninth clock
Dummy read of SSPBUF
to clear BF flag
1
A6
Receive Second Byte of Address
9
ACK
2
4
5
6
Cleared in software
3
D3 D2
7
8
1
4
5
6
Cleared in software
3
CKP written to ‘1’
in software
2
D3 D2
Receive Data Byte
D7 D6 D5 D4
Note: An update of the SSPADD register before the
falling edge of the ninth clock will have no effect
on UA and UA will remain set.
9
ACK
Clock is held low until
CKP is set to ‘1’
D1 D0
Cleared by hardware when
SSPADD is updated with high
byte of address after falling edge
of ninth clock
Dummy read of SSPBUF
to clear BF flag
1
D7 D6 D5 D4
Receive Data Byte
Clock is held low until
update of SSPADD has
taken place
7
8
9
ACK
Bus master
terminates
transfer
P
SSPOV is set
because SSPBUF is
still full. ACK is not sent.
D1 D0
Clock is not held low
because ACK = 1
FIGURE 16-16:
SDA
Receive First Byte of Address
Clock is held low until
update of SSPADD has
taken place
PIC18F85J90 FAMILY
I2C™ SLAVE MODE TIMING WITH SEN = 1 (RECEPTION, 10-BIT ADDRESS)
DS39770B-page 211
PIC18F85J90 FAMILY
16.4.5
GENERAL CALL ADDRESS
SUPPORT
If the general call address matches, the SSPSR is
transferred to the SSPBUF, the BF flag bit is set (eighth
bit) and on the falling edge of the ninth bit (ACK bit), the
SSPIF interrupt flag bit is set.
The addressing procedure for the I2C bus is such that
the first byte after the Start condition usually
determines which device will be the slave addressed by
the master. The exception is the general call address
which can address all devices. When this address is
used, all devices should, in theory, respond with an
Acknowledge.
When the interrupt is serviced, the source for the
interrupt can be checked by reading the contents of the
SSPBUF. The value can be used to determine if the
address was device specific or a general call address.
In 10-bit mode, the SSPADD is required to be updated
for the second half of the address to match and the UA
bit is set (SSPSTAT<1>). If the general call address is
sampled when the GCEN bit is set, while the slave is
configured in 10-Bit Address mode, then the second
half of the address is not necessary, the UA bit will not
be set and the slave will begin receiving data after the
Acknowledge (Figure 16-17).
The general call address is one of eight addresses
reserved for specific purposes by the I2C protocol. It
consists of all ‘0’s with R/W = 0.
The general call address is recognized when the
General Call Enable bit, GCEN, is enabled
(SSPCON2<7> set). Following a Start bit detect, 8 bits
are shifted into the SSPSR and the address is
compared against the SSPADD. It is also compared to
the general call address and fixed in hardware.
FIGURE 16-17:
SLAVE MODE GENERAL CALL ADDRESS SEQUENCE
(7 OR 10-BIT ADDRESS MODE)
Address is compared to General Call Address
after ACK, set interrupt
Receiving Data
R/W = 0
General Call Address
SDA
ACK D7
ACK
D6
D5
D4
D3
D2
D1
D0
2
3
4
5
6
7
8
SCL
S
1
2
3
4
5
6
7
8
9
1
9
SSPIF
BF (SSPSTAT<0>)
Cleared in software
SSPBUF is read
SSPOV (SSPCON1<6>)
‘0’
GCEN (SSPCON2<7>)
‘1’
DS39770B-page 212
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
MASTER MODE
Note:
The MSSP module, when configured in
I2C Master mode, does not allow queueing
of events. For instance, the user is not
allowed to initiate a Start condition and
immediately write the SSPBUF register to
initiate transmission before the Start condition is complete. In this case, the
SSPBUF will not be written to and the
WCOL bit will be set, indicating that a write
to the SSPBUF did not occur.
Master mode is enabled by setting and clearing the
appropriate SSPM bits in SSPCON1 and by setting the
SSPEN bit. In Master mode, the SCL and SDA lines
are manipulated by the MSSP hardware.
Master mode of operation is supported by interrupt
generation on the detection of the Start and Stop conditions. The Stop (P) and Start (S) bits are cleared from
a Reset or when the MSSP module is disabled. Control
of the I 2C bus may be taken when the P bit is set, or the
bus is Idle, with both the S and P bits clear.
The following events will cause the MSSP Interrupt
Flag bit, SSPIF, to be set (and MSSP interrupt, if
enabled):
In Firmware Controlled Master mode, user code
conducts all I 2C bus operations based on Start and
Stop bit conditions.
•
•
•
•
•
Once Master mode is enabled, the user has six
options.
1.
2.
3.
4.
5.
6.
Assert a Start condition on SDA and SCL.
Assert a Repeated Start condition on SDA and
SCL.
Write to the SSPBUF register initiating
transmission of data/address.
Configure the I2C port to receive data.
Generate an Acknowledge condition at the end
of a received byte of data.
Generate a Stop condition on SDA and SCL.
FIGURE 16-18:
Start condition
Stop condition
Data transfer byte transmitted/received
Acknowledge transmit
Repeated Start
MSSP BLOCK DIAGRAM (I2C™ MASTER MODE)
Internal
Data Bus
Read
SSPM3:SSPM0
SSPADD<6:0>
Write
SSPBUF
Baud
Rate
Generator
Shift
Clock
SDA
SDA In
SCL In
Bus Collision
© 2007 Microchip Technology Inc.
LSb
Start bit, Stop bit,
Acknowledge
Generate
Start bit Detect
Stop bit Detect
Write Collision Detect
Clock Arbitration
State Counter for
End of XMIT/RCV
Preliminary
Clock Cntl
SCL
Receive Enable
SSPSR
MSb
Clock Arbitrate/WCOL Detect
(hold off clock source)
16.4.6
Set/Reset S, P, WCOL (SSPSTAT, SSPCON1)
Set SSPIF, BCLIF
Reset ACKSTAT, PEN (SSPCON2)
DS39770B-page 213
PIC18F85J90 FAMILY
16.4.6.1
I2C Master Mode Operation
A typical transmit sequence would go as follows:
The master device generates all of the serial clock
pulses and the Start and Stop conditions. A transfer is
ended with a Stop condition or with a Repeated Start
condition. Since the Repeated Start condition is also
the beginning of the next serial transfer, the I2C bus will
not be released.
In Master Transmitter mode, serial data is output
through SDA, while SCL outputs the serial clock. The
first byte transmitted contains the slave address of the
receiving device (7 bits) and the Read/Write (R/W) bit.
In this case, the R/W bit will be logic ‘0’. Serial data is
transmitted 8 bits at a time. After each byte is transmitted, an Acknowledge bit is received. Start and Stop
conditions are output to indicate the beginning and the
end of a serial transfer.
In Master Receive mode, the first byte transmitted
contains the slave address of the transmitting device
(7 bits) and the R/W bit. In this case, the R/W bit will be
logic ‘1’. Thus, the first byte transmitted is a 7-bit slave
address followed by a ‘1’ to indicate the receive bit.
Serial data is received via SDA, while SCL outputs the
serial clock. Serial data is received 8 bits at a time. After
each byte is received, an Acknowledge bit is transmitted. Start and Stop conditions indicate the beginning
and end of transmission.
The Baud Rate Generator used for the SPI mode
operation is used to set the SCL clock frequency for
either 100 kHz, 400 kHz or 1 MHz I2C operation. See
Section 16.4.7 “Baud Rate” for more detail.
DS39770B-page 214
1.
The user generates a Start condition by setting
the Start Enable bit, SEN (SSPCON2<0>).
2. SSPIF is set. The MSSP module will wait the
required start time before any other operation
takes place.
3. The user loads the SSPBUF with the slave
address to transmit.
4. Address is shifted out the SDA pin until all 8 bits
are transmitted.
5. The MSSP module shifts in the ACK bit from the
slave device and writes its value into the
SSPCON2 register (SSPCON2<6>).
6. The MSSP module generates an interrupt at the
end of the ninth clock cycle by setting the SSPIF
bit.
7. The user loads the SSPBUF with eight bits of
data.
8. Data is shifted out the SDA pin until all 8 bits are
transmitted.
9. The MSSP module shifts in the ACK bit from the
slave device and writes its value into the
SSPCON2 register (SSPCON2<6>).
10. The MSSP module generates an interrupt at the
end of the ninth clock cycle by setting the SSPIF
bit.
11. The user generates a Stop condition by setting
the Stop Enable bit, PEN (SSPCON2<2>).
12. Interrupt is generated once the Stop condition is
complete.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.4.7
BAUD RATE
2
In I C Master mode, the Baud Rate Generator (BRG)
reload value is placed in the lower 7 bits of the
SSPADD register (Figure 16-19). When a write occurs
to SSPBUF, the Baud Rate Generator will automatically
begin counting. The BRG counts down to ‘0’ and stops
until another reload has taken place. The BRG count is
decremented twice per instruction cycle (TCY) on the
Q2 and Q4 clocks. In I2C Master mode, the BRG is
reloaded automatically.
Once the given operation is complete (i.e., transmission of the last data bit is followed by ACK), the internal
clock will automatically stop counting and the SCL pin
will remain in its last state.
FIGURE 16-19:
Table 16-3 demonstrates clock rates based on
instruction cycles and the BRG value loaded into
SSPADD.
16.4.7.1
When the device is operating in one of the
power-managed modes, the clock source to the BRG
may change frequency or even stop, depending on the
mode and clock source selected. Switching to a Run or
Idle mode from either the secondary clock or internal
oscillator is likely to change the clock rate to the BRG.
In Sleep mode, the BRG will not be clocked at all.
BAUD RATE GENERATOR BLOCK DIAGRAM
SSPM3:SSPM0
SSPM3:SSPM0
Reload
SCL
Control
CLKO
SSPADD<6:0>
Reload
BRG Down Counter
FOSC/4
I2C™ CLOCK RATE w/BRG
TABLE 16-3:
Note 1:
Baud Rate Generation in
Power-Managed Modes
FCY
FCY * 2
BRG Value
FSCL
(2 Rollovers of BRG)
10 MHz
20 MHz
18h
400 kHz(1)
10 MHz
20 MHz
1Fh
312.5 kHz
10 MHz
20 MHz
63h
100 kHz
4 MHz
8 MHz
09h
400 kHz(1)
4 MHz
8 MHz
0Ch
308 kHz
4 MHz
8 MHz
27h
100 kHz
1 MHz
2 MHz
02h
333 kHz(1)
1 MHz
2 MHz
09h
100 kHz
1 MHz
2 MHz
00h
1 MHz(1)
I2C™
I2C
The
interface does not conform to the 400 kHz
specification (which applies to rates greater than
100 kHz) in all details, but may be used with care where higher rates are required by the application.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 215
PIC18F85J90 FAMILY
16.4.7.2
Clock Arbitration
Clock arbitration occurs when the master, during any
receive, transmit or Repeated Start/Stop condition,
deasserts the SCL pin (SCL allowed to float high).
When the SCL pin is allowed to float high, the Baud
Rate Generator (BRG) is suspended from counting
until the SCL pin is actually sampled high. When the
FIGURE 16-20:
SDA
SCL pin is sampled high, the Baud Rate Generator is
reloaded with the contents of SSPADD<6:0> and
begins counting. This ensures that the SCL high time
will always be at least one BRG rollover count in the
event that the clock is held low by an external device
(Figure 16-20).
BAUD RATE GENERATOR TIMING WITH CLOCK ARBITRATION
DX
DX – 1
SCL deasserted but slave holds
SCL low (clock arbitration)
SCL allowed to transition high
SCL
BRG decrements on
Q2 and Q4 cycles
BRG
Value
03h
02h
01h
00h (hold off)
03h
02h
SCL is sampled high, reload takes
place and BRG starts its count
BRG
Reload
DS39770B-page 216
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.4.8
I2C MASTER MODE START
CONDITION TIMING
Note:
To initiate a Start condition, the user sets the Start
Enable bit, SEN (SSPCON2<0>). If the SDA and SCL
pins are sampled high, the Baud Rate Generator is
reloaded with the contents of SSPADD<6:0> and starts
its count. If SCL and SDA are both sampled high when
the Baud Rate Generator times out (TBRG), the SDA
pin is driven low. The action of the SDA being driven
low while SCL is high is the Start condition and causes
the S bit (SSPSTAT<3>) to be set. Following this, the
Baud Rate Generator is reloaded with the contents of
SSPADD<6:0> and resumes its count. When the Baud
Rate Generator times out (TBRG), the SEN bit
(SSPCON2<0>) will be automatically cleared by
hardware. The Baud Rate Generator is suspended,
leaving the SDA line held low and the Start condition is
complete.
FIGURE 16-21:
16.4.8.1
If at the beginning of the Start condition,
the SDA and SCL pins are already sampled low, or if during the Start condition, the
SCL line is sampled low before the SDA
line is driven low, a bus collision occurs.
The Bus Collision Interrupt Flag, BCLIF, is
set, the Start condition is aborted and the
I2C module is reset into its Idle state.
WCOL Status Flag
If the user writes the SSPBUF when a Start sequence
is in progress, the WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur).
Note:
Because queueing of events is not
allowed, writing to the lower 5 bits of
SSPCON2 is disabled until the Start
condition is complete.
FIRST START BIT TIMING
Set S bit (SSPSTAT<3>)
Write to SEN bit occurs here
SDA = 1,
SCL = 1
TBRG
At completion of Start bit,
hardware clears SEN bit
and sets SSPIF bit
TBRG
Write to SSPBUF occurs here
1st bit
SDA
2nd bit
TBRG
SCL
TBRG
S
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 217
PIC18F85J90 FAMILY
16.4.9
I2C MASTER MODE REPEATED
START CONDITION TIMING
Note 1: If RSEN is programmed while any other
event is in progress, it will not take effect.
A Repeated Start condition occurs when the RSEN bit
(SSPCON2<1>) is programmed high and the I2C logic
module is in the Idle state. When the RSEN bit is set,
the SCL pin is asserted low. When the SCL pin is
sampled low, the Baud Rate Generator is loaded with
the contents of SSPADD<6:0> and begins counting.
The SDA pin is released (brought high) for one Baud
Rate Generator count (TBRG). When the Baud Rate
Generator times out, if SDA is sampled high, the SCL
pin will be deasserted (brought high). When SCL is
sampled high, the Baud Rate Generator is reloaded
with the contents of SSPADD<6:0> and begins
counting. SDA and SCL must be sampled high for one
TBRG. This action is then followed by assertion of the
SDA pin (SDA = 0) for one TBRG while SCL is high.
Following this, the RSEN bit (SSPCON2<1>) will be
automatically cleared and the Baud Rate Generator will
not be reloaded, leaving the SDA pin held low. As soon
as a Start condition is detected on the SDA and SCL
pins, the S bit (SSPSTAT<3>) will be set. The SSPIF bit
will not be set until the Baud Rate Generator has timed
out.
2: A bus collision during the Repeated Start
condition occurs if:
• SDA is sampled low when SCL goes
from low-to-high.
• SCL goes low before SDA is
asserted low. This may indicate that
another master is attempting to
transmit a data ‘1’.
Immediately following the SSPIF bit getting set, the user
may write the SSPBUF with the 7-bit address in 7-bit
mode or the default first address in 10-bit mode. After the
first eight bits are transmitted and an ACK is received,
the user may then transmit an additional eight bits of
address (10-bit mode) or eight bits of data (7-bit mode).
16.4.9.1
If the user writes the SSPBUF when a Repeated Start
sequence is in progress, the WCOL is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
Note:
FIGURE 16-22:
WCOL Status Flag
Because queueing of events is not
allowed, writing of the lower 5 bits of
SSPCON2 is disabled until the Repeated
Start condition is complete.
REPEATED START CONDITION WAVEFORM
S bit set by hardware
Write to SSPCON2 occurs here: SDA = 1,
SCL (no change)
SDA = 1,
SCL = 1
TBRG
TBRG
At completion of Start bit,
hardware clears RSEN bit
and sets SSPIF
TBRG
1st bit
SDA
RSEN bit set by hardware
on falling edge of ninth clock,
end of Xmit
Write to SSPBUF occurs here
TBRG
SCL
TBRG
Sr = Repeated Start
DS39770B-page 218
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.4.10
I2C MASTER MODE
TRANSMISSION
Transmission of a data byte, a 7-bit address or the
other half of a 10-bit address is accomplished by simply
writing a value to the SSPBUF register. This action will
set the Buffer Full bit, BF, and allow the Baud Rate
Generator to begin counting and start the next transmission. Each bit of address/data will be shifted out
onto the SDA pin after the falling edge of SCL is
asserted (see data hold time specification
parameter 106). SCL is held low for one Baud Rate
Generator rollover count (TBRG). Data should be valid
before SCL is released high (see data setup time
specification parameter 107). When the SCL pin is
released high, it is held that way for TBRG. The data on
the SDA pin must remain stable for that duration and
some hold time after the next falling edge of SCL. After
the eighth bit is shifted out (the falling edge of the eighth
clock), the BF flag is cleared and the master releases
SDA. This allows the slave device being addressed to
respond with an ACK bit during the ninth bit time if an
address match occurred, or if data was received properly. The status of ACK is written into the ACKDT bit on
the falling edge of the ninth clock. If the master receives
an Acknowledge, the Acknowledge Status bit,
ACKSTAT, is cleared; if not, the bit is set. After the ninth
clock, the SSPIF bit is set and the master clock (Baud
Rate Generator) is suspended until the next data byte
is loaded into the SSPBUF, leaving SCL low and SDA
unchanged (Figure 16-23).
After the write to the SSPBUF, each bit of the address
will be shifted out on the falling edge of SCL until all
seven address bits and the R/W bit are completed. On
the falling edge of the eighth clock, the master will
deassert the SDA pin, allowing the slave to respond
with an Acknowledge. On the falling edge of the ninth
clock, the master will sample the SDA pin to see if the
address was recognized by a slave. The status of the
ACK bit is loaded into the ACKSTAT status bit
(SSPCON2<6>). Following the falling edge of the ninth
clock transmission of the address, the SSPIF is set, the
BF flag is cleared and the Baud Rate Generator is
turned off until another write to the SSPBUF takes
place, holding SCL low and allowing SDA to float.
The user should verify that the WCOL is clear after
each write to SSPBUF to ensure the transfer is correct.
In all cases, WCOL must be cleared in software.
16.4.10.3
In Transmit mode, the ACKSTAT bit (SSPCON2<6>) is
cleared when the slave has sent an Acknowledge
(ACK = 0) and is set when the slave does not Acknowledge (ACK = 1). A slave sends an Acknowledge when
it has recognized its address (including a general call),
or when the slave has properly received its data.
16.4.11
BF Status Flag
In Transmit mode, the BF bit (SSPSTAT<0>) is set
when the CPU writes to SSPBUF and is cleared when
all 8 bits are shifted out.
16.4.10.2
I2C MASTER MODE RECEPTION
Master mode reception is enabled by programming the
Receive Enable bit, RCEN (SSPCON2<3>).
Note:
The MSSP module must be in an Idle state
before the RCEN bit is set or the RCEN bit
will be disregarded.
The Baud Rate Generator begins counting and on each
rollover, the state of the SCL pin changes
(high-to-low/low-to-high) and data is shifted into the
SSPSR. After the falling edge of the eighth clock, the
receive enable flag is automatically cleared, the contents of the SSPSR are loaded into the SSPBUF, the
BF flag bit is set, the SSPIF flag bit is set and the Baud
Rate Generator is suspended from counting, holding
SCL low. The MSSP is now in Idle state awaiting the
next command. When the buffer is read by the CPU,
the BF flag bit is automatically cleared. The user can
then send an Acknowledge bit at the end of reception
by setting the Acknowledge Sequence Enable bit,
ACKEN (SSPCON2<4>).
16.4.11.1
BF Status Flag
In receive operation, the BF bit is set when an address
or data byte is loaded into SSPBUF from SSPSR. It is
cleared when the SSPBUF register is read.
16.4.11.2
SSPOV Status Flag
In receive operation, the SSPOV bit is set when 8 bits
are received into the SSPSR and the BF flag bit is
already set from a previous reception.
16.4.11.3
16.4.10.1
ACKSTAT Status Flag
WCOL Status Flag
If the user writes the SSPBUF when a receive is
already in progress (i.e., SSPSR is still shifting in a data
byte), the WCOL bit is set and the contents of the buffer
are unchanged (the write doesn’t occur).
WCOL Status Flag
If the user writes to the SSPBUF when a transmit is
already in progress (i.e., SSPSR is still shifting out a
data byte), the WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur) after
2 TCY after the SSPBUF write. If SSPBUF is rewritten
within 2 TCY, the WCOL bit is set and SSPBUF is
updated. This may result in a corrupted transfer.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 219
DS39770B-page 220
S
Preliminary
R/W
PEN
SEN
BF (SSPSTAT<0>)
SSPIF
SCL
SDA
A6
A5
A4
A3
A2
A1
3
4
5
Cleared in software
2
6
7
8
9
After Start condition, SEN cleared by hardware
SSPBUF written
1
D7
1
SCL held low
while CPU
responds to SSPIF
ACK = 0
R/W = 0
SSPBUF written with 7-bit address and R/W
start transmit
A7
Transmit Address to Slave
3
D5
4
D4
5
D3
6
D2
7
D1
8
D0
SSPBUF is written in software
Cleared in software service routine
from MSSP interrupt
2
D6
Transmitting Data or Second Half
of 10-bit Address
P
Cleared in software
9
ACK
From slave, clear ACKSTAT bit (SSPCON2<6>)
ACKSTAT in
SSPCON2 = 1
FIGURE 16-23:
SEN = 0
Write SSPCON2<0> (SEN = 1),
Start condition begins
PIC18F85J90 FAMILY
I 2C™ MASTER MODE WAVEFORM (TRANSMISSION, 7 OR 10-BIT ADDRESS)
© 2007 Microchip Technology Inc.
© 2007 Microchip Technology Inc.
S
Preliminary
ACKEN
SSPOV
BF
(SSPSTAT<0>)
SDA = 0, SCL = 1
while CPU
responds to SSPIF
SSPIF
SCL
SDA
Transmit Address to Slave
1
2
4
5
6
Cleared in software
3
7
A7 A6 A5 A4 A3 A2 A1
8
9
R/W = 0
ACK
ACK from Slave
2
3
5
6
7
8
D0
9
ACK
2
3
4
5
6
7
Cleared in software
Set SSPIF interrupt
at end of Acknowledge
sequence
Data shifted in on falling edge of CLK
1
D7 D6 D5 D4 D3 D2 D1
Cleared in
software
Set SSPIF at end
of receive
9
ACK is not sent
ACK
Bus master
terminates
transfer
Set P bit
(SSPSTAT<4>)
and SSPIF
Set SSPIF interrupt
at end of Acknowledge
sequence
P
PEN bit = 1
written here
SSPOV is set because
SSPBUF is still full
8
D0
RCEN cleared
automatically
Set ACKEN, start Acknowledge sequence,
SDA = ACKDT = 1
Receiving Data from Slave
RCEN = 1, start
next receive
ACK from Master,
SDA = ACKDT = 0
Last bit is shifted into SSPSR and
contents are unloaded into SSPBUF
Cleared in software
Set SSPIF interrupt
at end of receive
4
Cleared in software
1
D7 D6 D5 D4 D3 D2 D1
Receiving Data from Slave
RCEN cleared
automatically
Master configured as a receiver
by programming SSPCON2<3> (RCEN = 1)
FIGURE 16-24:
SEN = 0
Write to SSPBUF occurs here,
start XMIT
Write to SSPCON2<0> (SEN = 1),
begin Start condition
Write to SSPCON2<4>
to start Acknowledge sequence,
SDA = ACKDT (SSPCON2<5>) = 0
PIC18F85J90 FAMILY
I 2C™ MASTER MODE WAVEFORM (RECEPTION, 7-BIT ADDRESS)
DS39770B-page 221
PIC18F85J90 FAMILY
16.4.12
ACKNOWLEDGE SEQUENCE
TIMING
16.4.13
A Stop bit is asserted on the SDA pin at the end of a
receive/transmit by setting the Stop Sequence Enable
bit, PEN (SSPCON2<2>). At the end of a
receive/transmit, the SCL line is held low after the falling edge of the ninth clock. When the PEN bit is set, the
master will assert the SDA line low. When the SDA line
is sampled low, the Baud Rate Generator is reloaded
and counts down to ‘0’. When the Baud Rate Generator
times out, the SCL pin will be brought high and one
TBRG (Baud Rate Generator rollover count) later, the
SDA pin will be deasserted. When the SDA pin is
sampled high while SCL is high, the P bit
(SSPSTAT<4>) is set. A TBRG later, the PEN bit is
cleared and the SSPIF bit is set (Figure 16-26).
An Acknowledge sequence is enabled by setting the
Acknowledge Sequence Enable bit, ACKEN
(SSPCON2<4>). When this bit is set, the SCL pin is
pulled low and the contents of the Acknowledge data bit
are presented on the SDA pin. If the user wishes to generate an Acknowledge, then the ACKDT bit should be
cleared. If not, the user should set the ACKDT bit before
starting an Acknowledge sequence. The Baud Rate
Generator then counts for one rollover period (TBRG)
and the SCL pin is deasserted (pulled high). When the
SCL pin is sampled high (clock arbitration), the Baud
Rate Generator counts for TBRG. The SCL pin is then
pulled low. Following this, the ACKEN bit is automatically
cleared, the Baud Rate Generator is turned off and the
MSSP module then goes into Idle mode (Figure 16-25).
16.4.12.1
16.4.13.1
WCOL Status Flag
If the user writes the SSPBUF when a Stop sequence
is in progress, then the WCOL bit is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
WCOL Status Flag
If the user writes the SSPBUF when an Acknowledge
sequence is in progress, then WCOL is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
FIGURE 16-25:
STOP CONDITION TIMING
ACKNOWLEDGE SEQUENCE WAVEFORM
Acknowledge sequence starts here,
write to SSPCON2,
ACKEN = 1, ACKDT = 0
SDA
D0
SCL
8
ACKEN automatically cleared
TBRG
TBRG
ACK
9
SSPIF
SSPIF set at
the end of receive
Cleared in
software
Cleared in
software
SSPIF set at the end
of Acknowledge sequence
Note: TBRG = one Baud Rate Generator period.
FIGURE 16-26:
STOP CONDITION RECEIVE OR TRANSMIT MODE
Write to SSPCON2,
set PEN
SCL = 1 for TBRG, followed by SDA = 1 for TBRG
after SDA sampled high. P bit (SSPSTAT<4>) is set.
Falling edge of
9th clock
PEN bit (SSPCON2<2>) is cleared by
hardware and the SSPIF bit is set
TBRG
SCL
SDA
ACK
P
TBRG
TBRG
TBRG
SCL brought high after TBRG
SDA asserted low before rising edge of clock
to setup Stop condition
Note: TBRG = one Baud Rate Generator period.
DS39770B-page 222
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.4.14
SLEEP OPERATION
16.4.17
2
While in Sleep mode, the I C module can receive
addresses or data and when an address match or
complete byte transfer occurs, wake the processor
from Sleep (if the MSSP interrupt is enabled).
16.4.15
EFFECTS OF A RESET
A Reset disables the MSSP module and terminates the
current transfer.
16.4.16
MULTI-MASTER MODE
In Multi-Master mode, the interrupt generation on the
detection of the Start and Stop conditions allows the
determination of when the bus is free. The Stop (P) and
Start (S) bits are cleared from a Reset or when the
MSSP module is disabled. Control of the I 2C bus may
be taken when the P bit (SSPSTAT<4>) is set, or the
bus is Idle, with both the S and P bits clear. When the
bus is busy, enabling the MSSP interrupt will generate
the interrupt when the Stop condition occurs.
In multi-master operation, the SDA line must be
monitored for arbitration to see if the signal level is the
expected output level. This check is performed in
hardware with the result placed in the BCLIF bit.
The states where arbitration can be lost are:
•
•
•
•
•
Address Transfer
Data Transfer
A Start Condition
A Repeated Start Condition
An Acknowledge Condition
MULTI -MASTER COMMUNICATION,
BUS COLLISION AND BUS
ARBITRATION
Multi-Master mode support is achieved by bus arbitration. When the master outputs address/data bits onto
the SDA pin, arbitration takes place when the master
outputs a ‘1’ on SDA by letting SDA float high, and
another master asserts a ‘0’. When the SCL pin floats
high, data should be stable. If the expected data on
SDA is a ‘1’ and the data sampled on the SDA pin = 0,
then a bus collision has taken place. The master will set
the Bus Collision Interrupt Flag, BCLIF and reset the
I2C port to its Idle state (Figure 16-27).
If a transmit was in progress when the bus collision
occurred, the transmission is halted, the BF flag is
cleared, the SDA and SCL lines are deasserted and the
SSPBUF can be written to. When the user services the
bus collision Interrupt Service Routine and if the I2C bus
is free, the user can resume communication by asserting
a Start condition.
If a Start, Repeated Start, Stop or Acknowledge condition
was in progress when the bus collision occurred, the
condition is aborted, the SDA and SCL lines are deasserted and the respective control bits in the SSPCON2
register are cleared. When the user services the bus
collision Interrupt Service Routine and if the I2C bus is
free, the user can resume communication by asserting a
Start condition.
The master will continue to monitor the SDA and SCL
pins. If a Stop condition occurs, the SSPIF bit will be set.
A write to the SSPBUF will start the transmission of
data at the first data bit regardless of where the
transmitter left off when the bus collision occurred.
In Multi-Master mode, the interrupt generation on the
detection of Start and Stop conditions allows the determination of when the bus is free. Control of the I2C bus
can be taken when the P bit is set in the SSPSTAT
register, or the bus is Idle and the S and P bits are
cleared.
FIGURE 16-27:
BUS COLLISION TIMING FOR TRANSMIT AND ACKNOWLEDGE
Data changes
while SCL = 0
SDA line pulled low
by another source
SDA released
by master
Sample SDA. While SCL is high,
data doesn’t match what is driven
by the master.
Bus collision has occurred.
SDA
SCL
Set bus collision
interrupt (BCLIF)
BCLIF
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 223
PIC18F85J90 FAMILY
16.4.17.1
Bus Collision During a Start
Condition
During a Start condition, a bus collision occurs if:
a)
b)
SDA or SCL are sampled low at the beginning of
the Start condition (Figure 16-28).
SCL is sampled low before SDA is asserted low
(Figure 16-29).
During a Start condition, both the SDA and the SCL
pins are monitored.
If the SDA pin is sampled low during this count, the
BRG is reset and the SDA line is asserted early
(Figure 16-30). If, however, a ‘1’ is sampled on the SDA
pin, the SDA pin is asserted low at the end of the BRG
count. The Baud Rate Generator is then reloaded and
counts down to ‘0’. If the SCL pin is sampled as ‘0’
during this time, a bus collision does not occur. At the
end of the BRG count, the SCL pin is asserted low.
Note:
If the SDA pin is already low, or the SCL pin is already
low, then all of the following occur:
• the Start condition is aborted;
• the BCLIF flag is set; and
• the MSSP module is reset to its Idle state
(Figure 16-28).
The Start condition begins with the SDA and SCL pins
deasserted. When the SDA pin is sampled high, the
Baud Rate Generator is loaded from SSPADD<6:0>
and counts down to ‘0’. If the SCL pin is sampled low
while SDA is high, a bus collision occurs, because it is
assumed that another master is attempting to drive a
data ‘1’ during the Start condition.
FIGURE 16-28:
The reason that bus collision is not a factor
during a Start condition is that no two bus
masters can assert a Start condition at the
exact same time. Therefore, one master
will always assert SDA before the other.
This condition does not cause a bus collision because the two masters must be
allowed to arbitrate the first address
following the Start condition. If the address
is the same, arbitration must be allowed to
continue into the data portion, Repeated
Start or Stop conditions.
BUS COLLISION DURING START CONDITION (SDA ONLY)
SDA goes low before the SEN bit is set.
Set BCLIF,
S bit and SSPIF set because
SDA = 0, SCL = 1.
SDA
SCL
Set SEN, enable Start
condition if SDA = 1, SCL = 1
SEN cleared automatically because of bus collision.
MSSP module reset into Idle state.
SEN
BCLIF
SDA sampled low before
Start condition. Set BCLIF.
S bit and SSPIF set because
SDA = 0, SCL = 1.
SSPIF and BCLIF are
cleared in software
S
SSPIF
SSPIF and BCLIF are
cleared in software
DS39770B-page 224
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 16-29:
BUS COLLISION DURING START CONDITION (SCL = 0)
SDA = 0, SCL = 1
TBRG
TBRG
SDA
Set SEN, enable Start
sequence if SDA = 1, SCL = 1
SCL
SCL = 0 before SDA = 0,
bus collision occurs. Set BCLIF.
SEN
SCL = 0 before BRG time-out,
bus collision occurs. Set BCLIF.
BCLIF
Interrupt cleared
in software
S
‘0’
‘0’
SSPIF
‘0’
‘0’
FIGURE 16-30:
BRG RESET DUE TO SDA ARBITRATION DURING START CONDITION
SDA = 0, SCL = 1
Set S
Less than TBRG
SDA
Set SSPIF
TBRG
SDA pulled low by other master.
Reset BRG and assert SDA.
SCL
S
SCL pulled low after BRG
time-out
SEN
BCLIF
Set SEN, enable Start
sequence if SDA = 1, SCL = 1
‘0’
S
SSPIF
SDA = 0, SCL = 1,
set SSPIF
© 2007 Microchip Technology Inc.
Preliminary
Interrupts cleared
in software
DS39770B-page 225
PIC18F85J90 FAMILY
16.4.17.2
Bus Collision During a Repeated
Start Condition
If SDA is low, a bus collision has occurred (i.e., another
master is attempting to transmit a data ‘0’, see
Figure 16-31). If SDA is sampled high, the BRG is
reloaded and begins counting. If SDA goes from
high-to-low before the BRG times out, no bus collision
occurs because no two masters can assert SDA at
exactly the same time.
During a Repeated Start condition, a bus collision
occurs if:
a)
b)
A low level is sampled on SDA when SCL goes
from low level to high level.
SCL goes low before SDA is asserted low,
indicating that another master is attempting to
transmit a data ‘1’.
If SCL goes from high-to-low before the BRG times out
and SDA has not already been asserted, a bus collision
occurs. In this case, another master is attempting to
transmit a data ‘1’ during the Repeated Start condition
(see Figure 16-32).
When the user deasserts SDA and the pin is allowed to
float high, the BRG is loaded with SSPADD<6:0> and
counts down to ‘0’. The SCL pin is then deasserted and
when sampled high, the SDA pin is sampled.
FIGURE 16-31:
If, at the end of the BRG time-out, both SCL and SDA
are still high, the SDA pin is driven low and the BRG is
reloaded and begins counting. At the end of the count,
regardless of the status of the SCL pin, the SCL pin is
driven low and the Repeated Start condition is complete.
BUS COLLISION DURING A REPEATED START CONDITION (CASE 1)
SDA
SCL
Sample SDA when SCL goes high.
If SDA = 0, set BCLIF and release SDA and SCL.
RSEN
BCLIF
Cleared in software
S
‘0’
SSPIF
‘0’
FIGURE 16-32:
BUS COLLISION DURING REPEATED START CONDITION (CASE 2)
TBRG
TBRG
SDA
SCL
BCLIF
SCL goes low before SDA,
set BCLIF. Release SDA and SCL.
Interrupt cleared
in software
RSEN
‘0’
S
SSPIF
DS39770B-page 226
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
16.4.17.3
Bus Collision During a Stop
Condition
The Stop condition begins with SDA asserted low.
When SDA is sampled low, the SCL pin is allowed to
float. When the pin is sampled high (clock arbitration),
the Baud Rate Generator is loaded with SSPADD<6:0>
and counts down to ‘0’. After the BRG times out, SDA
is sampled. If SDA is sampled low, a bus collision has
occurred. This is due to another master attempting to
drive a data ‘0’ (Figure 16-33). If the SCL pin is
sampled low before SDA is allowed to float high, a bus
collision occurs. This is another case of another master
attempting to drive a data ‘0’ (Figure 16-34).
Bus collision occurs during a Stop condition if:
a)
b)
After the SDA pin has been deasserted and
allowed to float high, SDA is sampled low after
the BRG has timed out.
After the SCL pin is deasserted, SCL is sampled
low before SDA goes high.
FIGURE 16-33:
BUS COLLISION DURING A STOP CONDITION (CASE 1)
TBRG
TBRG
TBRG
SDA sampled
low after TBRG,
set BCLIF
SDA
SDA asserted low
SCL
PEN
BCLIF
P
‘0’
SSPIF
‘0’
FIGURE 16-34:
BUS COLLISION DURING A STOP CONDITION (CASE 2)
TBRG
TBRG
TBRG
SDA
SCL goes low before SDA goes high,
set BCLIF
Assert SDA
SCL
PEN
BCLIF
P
‘0’
SSPIF
‘0’
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 227
PIC18F85J90 FAMILY
TABLE 16-4:
Name
INTCON
REGISTERS ASSOCIATED WITH I2C™ OPERATION
Bit 7
Bit 6
GIE/GIEH PEIE/GIEL
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
IPR1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
PIR2
OSCFIF
CMIF
—
—
BCLIF
LVDIF
TMR3IF
—
54
PIE2
OSCFIE
CMIE
—
—
BCLIE
LVDIE
TMR3IE
—
54
IPR2
OSCFIP
CMIP
—
—
BCLIP
LVDIP
TMR3IP
—
54
TRISC
TRISC7
TRISC6
TRISC5
TRISC4
TRISC3
TRISC2
TRISC1
TRISC0
54
SSPBUF
SSPADD
MSSP Receive Buffer/Transmit Register
52
(I2C™
MSSP Address Register
Slave mode),
MSSP Baud Rate Reload Register (I2C Master mode)
52
SSPCON1
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
52
SSPCON2
GCEN
ACKSTAT
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
52
ACKSTAT
ADMSK5(1)
ADMSK4(1)
ADMSK3(1)
ADMSK2(1)
ADMSK1(1)
SEN
D/A
P
S
R/W
UA
BF
GCEN
SSPSTAT
SMP
CKE
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the MSSP module in
Note 1: Alternate bit definitions for use in I2C Slave mode operations only.
DS39770B-page 228
Preliminary
I2C™
52
mode.
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
17.0
ENHANCED UNIVERSAL
SYNCHRONOUS
ASYNCHRONOUS RECEIVER
TRANSMITTER (EUSART)
PIC18F85J90 family devices have three serial I/O modules: the MSSP module, discussed in the previous
chapter and two Universal Synchronous Asynchronous
Receiver Transmitter (USART) modules. (Generically,
the USART is also known as a Serial Communications
Interface or SCI.) The USART can be configured as a
full-duplex asynchronous system that can communicate with peripheral devices, such as CRT terminals
and personal computers. It can also be configured as a
half-duplex synchronous system that can communicate
with peripheral devices, such as A/D or D/A integrated
circuits, serial EEPROMs, etc.
There are two distinct implementations of the USART
module in these devices: the Enhanced USART
(EUSART) discussed here and the Addressable
USART discussed in the next chapter. For this device
family, USART1 always refers to the EUSART, while
USART2 is always the AUSART.
The EUSART and AUSART modules implement the
same core features for serial communications; their
basic operation is essentially the same. The EUSART
module provides additional features, including Automatic Baud Rate Detection and calibration, automatic
wake-up on Sync Break reception and 12-bit Break
character transmit. These features make it ideally
suited for use in Local Interconnect Network bus (LIN
bus) systems.
The pins of the EUSART are multiplexed with the
functions of PORTC (RC6/TX1/CK1/SEG27 and
RC7/RX1/DT1/SEG28). In order to configure these
pins as an EUSART:
• bit SPEN (RCSTA1<7>) must be set (= 1)
• bit TRISC<7> must be set (= 1)
• bit TRISC<6> must be set (= 1)
Note:
The EUSART control will automatically
reconfigure the pin from input to output as
needed.
The driver for the TX1 output pin can also be optionally
configured as an open-drain output. This feature allows
the voltage level on the pin to be pulled to a higher level
through an external pull-up resistor, and allows the output to communicate with external circuits without the
need for additional level shifters.
The open-drain output option is controlled by the U1OD
bit (LATG<6>). Setting the bit configures the pin for
open-drain operation.
17.1
Control Registers
The operation of the Enhanced USART module is
controlled through three registers:
• Transmit Status and Control Register 1 (TXSTA1)
• Receive Status and Control Register 1 (RCSTA1)
• Baud Rate Control Register 1 (BAUDCON1)
The registers are described
Register 17-2 and Register 17-3.
in
Register 17-1,
The EUSART can be configured in the following
modes:
• Asynchronous (full-duplex) with:
- Auto-wake-up on character reception
- Auto-baud calibration
- 12-bit Break character transmission
• Synchronous – Master (half-duplex) with
selectable clock polarity
• Synchronous – Slave (half-duplex) with selectable
clock polarity
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 229
PIC18F85J90 FAMILY
REGISTER 17-1:
TXSTA1: EUSART TRANSMIT STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R-1
R/W-0
CSRC
TX9
TXEN(1)
SYNC
SENDB
BRGH
TRMT
TX9D
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
CSRC: Clock Source Select bit
Asynchronous mode:
Don’t care.
Synchronous mode:
1 = Master mode (clock generated internally from BRG)
0 = Slave mode (clock from external source)
bit 6
TX9: 9-Bit Transmit Enable bit
1 = Selects 9-bit transmission
0 = Selects 8-bit transmission
bit 5
TXEN: Transmit Enable bit(1)
1 = Transmit enabled
0 = Transmit disabled
bit 4
SYNC: AUSART Mode Select bit
1 = Synchronous mode
0 = Asynchronous mode
bit 3
SENDB: Send Break Character bit
Asynchronous mode:
1 = Send Sync Break on next transmission (cleared by hardware upon completion)
0 = Sync Break transmission completed
Synchronous mode:
Don’t care.
bit 2
BRGH: High Baud Rate Select bit
Asynchronous mode:
1 = High speed
0 = Low speed
Synchronous mode:
Unused in this mode.
bit 1
TRMT: Transmit Shift Register Status bit
1 = TSR empty
0 = TSR full
bit 0
TX9D: 9th bit of Transmit Data
Can be address/data bit or a parity bit.
Note 1:
SREN/CREN overrides TXEN in Sync mode.
DS39770B-page 230
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 17-2:
RCSTA1: EUSART RECEIVE STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R-0
R-0
R-x
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
SPEN: Serial Port Enable bit
1 = Serial port enabled (configures RX1/DT1 and TX1/CK1 pins as serial port pins)
0 = Serial port disabled (held in Reset)
bit 6
RX9: 9-Bit Receive Enable bit
1 = Selects 9-bit reception
0 = Selects 8-bit reception
bit 5
SREN: Single Receive Enable bit
Asynchronous mode:
Don’t care.
Synchronous mode – Master:
1 = Enables single receive
0 = Disables single receive
This bit is cleared after reception is complete.
Synchronous mode – Slave:
Don’t care.
bit 4
CREN: Continuous Receive Enable bit
Asynchronous mode:
1 = Enables receiver
0 = Disables receiver
Synchronous mode:
1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN)
0 = Disables continuous receive
bit 3
ADDEN: Address Detect Enable bit
Asynchronous mode 9-bit (RX9 = 1):
1 = Enables address detection, enables interrupt and loads the receive buffer when RSR<8> is set
0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit
Asynchronous mode 9-bit (RX9 = 0):
Don’t care.
bit 2
FERR: Framing Error bit
1 = Framing error (can be updated by reading RCREG1 register and receiving next valid byte)
0 = No framing error
bit 1
OERR: Overrun Error bit
1 = Overrun error (can be cleared by clearing bit CREN)
0 = No overrun error
bit 0
RX9D: 9th bit of Received Data
This can be address/data bit or a parity bit and must be calculated by user firmware.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 231
PIC18F85J90 FAMILY
REGISTER 17-3:
BAUDCON1: BAUD RATE CONTROL REGISTER 1
R/W-0
R-1
U-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
ABDOVF
RCMT
—
SCKP
BRG16
—
WUE
ABDEN
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
ABDOVF: Auto-Baud Acquisition Rollover Status bit
1 = A BRG rollover has occurred during Auto-Baud Rate Detect mode
(must be cleared in software)
0 = No BRG rollover has occurred
bit 6
RCMT: Receive Operation Idle Status bit
1 = Receive operation is Idle
0 = Receive operation is active
bit 5
Unimplemented: Read as ‘0’
bit 4
SCKP: Synchronous Clock Polarity Select bit
Asynchronous mode:
Unused in this mode.
Synchronous mode:
1 = Idle state for clock (CK1) is a high level
0 = Idle state for clock (CK1) is a low level
bit 3
BRG16: 16-Bit Baud Rate Register Enable bit
1 = 16-bit Baud Rate Generator – SPBRGH1 and SPBRG1
0 = 8-bit Baud Rate Generator – SPBRG1 only (Compatible mode), SPBRGH1 value ignored
bit 2
Unimplemented: Read as ‘0’
bit 1
WUE: Wake-up Enable bit
Asynchronous mode:
1 = EUSART will continue to sample the RX1 pin – interrupt generated on falling edge; bit cleared in
hardware on following rising edge
0 = RX1 pin not monitored or rising edge detected
Synchronous mode:
Unused in this mode.
bit 0
ABDEN: Auto-Baud Detect Enable bit
Asynchronous mode:
1 = Enable baud rate measurement on the next character. Requires reception of a Sync field (55h);
cleared in hardware upon completion.
0 = Baud rate measurement disabled or completed
Synchronous mode:
Unused in this mode.
DS39770B-page 232
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
17.2
EUSART Baud Rate Generator
(BRG)
geous to use the high baud rate (BRGH = 1) or the 16-bit
BRG to reduce the baud rate error, or achieve a slow
baud rate for a fast oscillator frequency.
The BRG is a dedicated, 8-bit or 16-bit generator that
supports both the Asynchronous and Synchronous
modes of the EUSART. By default, the BRG operates
in 8-bit mode; setting the BRG16 bit (BAUDCON1<3>)
selects 16-bit mode.
The SPBRGH1:SPBRG1 register pair controls the
period of a free-running timer. In Asynchronous mode,
BRGH (TXSTA1<2>) and BRG16 (BAUDCON1<3>) bits
also control the baud rate. In Synchronous mode, BRGH
is ignored. Table 17-1 shows the formula for computation of the baud rate for different EUSART modes that
only apply in Master mode (internally generated clock).
Given the desired baud rate and FOSC, the nearest
integer value for the SPBRGH1:SPBRG1 registers can
be calculated using the formulas in Table 17-1. From
this, the error in baud rate can be determined. An example calculation is shown in Example 17-1. Typical baud
rates and error values for the various Asynchronous
modes are shown in Table 17-2. It may be advanta-
TABLE 17-1:
Writing a new value to the SPBRGH1:SPBRG1 registers causes the BRG timer to be reset (or cleared). This
ensures the BRG does not wait for a timer overflow
before outputting the new baud rate.
17.2.1
OPERATION IN POWER-MANAGED
MODES
The device clock is used to generate the desired baud
rate. When one of the power-managed modes is
entered, the new clock source may be operating at a
different frequency. This may require an adjustment to
the value in the SPBRG1 register pair.
17.2.2
SAMPLING
The data on the RX1 pin is sampled three times by a
majority detect circuit to determine if a high or a low
level is present at the RX1 pin.
BAUD RATE FORMULAS
Configuration Bits
SYNC
BRG16
BRGH
BRG/EUSART Mode
Baud Rate Formula
0
0
0
8-bit/Asynchronous
0
0
1
8-bit/Asynchronous
0
1
0
16-bit/Asynchronous
0
1
1
16-bit/Asynchronous
1
0
x
8-bit/Synchronous
1
1
x
16-bit/Synchronous
Legend: x = Don’t care, n = Value of SPBRGH1:SPBRG1 register pair
EXAMPLE 17-1:
FOSC/[64 (n + 1)]
FOSC/[16 (n + 1)]
FOSC/[4 (n + 1)]
CALCULATING BAUD RATE ERROR
For a device with FOSC of 16 MHz, desired baud rate of 9600, Asynchronous mode, 8-bit BRG:
Desired Baud Rate
= FOSC/(64 ([SPBRGH1:SPBRG1] + 1))
Solving for SPBRGH1:SPBRG1:
X = ((FOSC/Desired Baud Rate)/64) – 1
= ((16000000/9600)/64) – 1
= [25.042] = 25
Calculated Baud Rate = 16000000/(64 (25 + 1))
= 9615
Error
= (Calculated Baud Rate – Desired Baud Rate)/Desired Baud Rate
= (9615 – 9600)/9600 = 0.16%
TABLE 17-2:
Name
REGISTERS ASSOCIATED WITH THE BAUD RATE GENERATOR
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TXSTA1
RCSTA1
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
BAUDCON1 ABDOVF RCMT
—
SCKP
BRG16
—
WUE
SPBRGH1
EUSART Baud Rate Generator Register High Byte
SPBRG1
EUSART Baud Rate Generator Register Low Byte
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the BRG.
© 2007 Microchip Technology Inc.
Preliminary
Reset Values
on Page
Bit 0
TX9D
RX9D
ABDEN
53
53
55
55
53
DS39770B-page 233
PIC18F85J90 FAMILY
TABLE 17-3:
BAUD RATES FOR ASYNCHRONOUS MODES
SYNC = 0, BRGH = 0, BRG16 = 0
BAUD
RATE
(K)
FOSC = 40.000 MHz
FOSC = 20.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
—
1.221
2.441
1.73
255
9.615
0.16
64
19.2
19.531
1.73
31
57.6
56.818
-1.36
115.2
125.000
8.51
Actual
Rate
(K)
%
Error
0.3
—
—
1.2
—
2.4
9.6
FOSC = 10.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
1.73
255
1.202
2.404
0.16
129
9.766
1.73
31
19.531
1.73
10
62.500
4
104.167
SPBRG
value
FOSC = 8.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
0.16
129
1.201
-0.16
103
2.404
0.16
64
2.403
-0.16
51
9.766
1.73
15
9.615
-0.16
12
15
19.531
1.73
7
—
—
—
8.51
4
52.083
-9.58
2
—
—
—
-9.58
2
78.125
-32.18
1
—
—
—
SPBRG
value
SPBRG
value
SPBRG
value
(decimal)
SYNC = 0, BRGH = 0, BRG16 = 0
BAUD
RATE
(K)
FOSC = 4.000 MHz
FOSC = 2.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
0.16
207
0.300
0.16
51
1.201
2.404
0.16
25
9.6
8.929
-6.99
19.2
20.833
FOSC = 1.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
-0.16
103
0.300
-0.16
51
-0.16
25
1.201
-0.16
12
2.403
-0.16
12
—
—
—
6
—
—
—
—
—
—
8.51
2
—
—
—
—
—
—
Actual
Rate
(K)
%
Error
0.3
0.300
1.2
1.202
2.4
SPBRG
value
SPBRG
value
SPBRG
value
(decimal)
57.6
62.500
8.51
0
—
—
—
—
—
—
115.2
62.500
-45.75
0
—
—
—
—
—
—
SYNC = 0, BRGH = 1, BRG16 = 0
BAUD
RATE
(K)
FOSC = 40.000 MHz
FOSC = 20.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
—
—
—
—
—
9.766
1.73
255
Actual
Rate
(K)
%
Error
0.3
—
1.2
—
2.4
9.6
SPBRG
value
FOSC = 10.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
—
—
—
—
—
9.615
0.16
FOSC = 8.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
—
—
—
—
—
2.441
1.73
255
2.403
-0.16
207
129
9.615
0.16
64
9.615
-0.16
51
25
SPBRG
value
SPBRG
value
SPBRG
value
(decimal)
—
19.2
19.231
0.16
129
19.231
0.16
64
19.531
1.73
31
19.230
-0.16
57.6
58.140
0.94
42
56.818
-1.36
21
56.818
-1.36
10
55.555
3.55
8
115.2
113.636
-1.36
21
113.636
-1.36
10
125.000
8.51
4
—
—
—
SYNC = 0, BRGH = 1, BRG16 = 0
BAUD
RATE
(K)
FOSC = 4.000 MHz
Actual
Rate
(K)
%
Error
FOSC = 2.000 MHz
SPBRG
value
(decimal)
Actual
Rate
(K)
%
Error
SPBRG
value
(decimal)
FOSC = 1.000 MHz
Actual
Rate
(K)
%
Error
SPBRG
value
(decimal)
0.3
—
—
—
—
—
—
0.300
-0.16
207
1.2
1.202
0.16
207
1.201
-0.16
103
1.201
-0.16
51
2.4
2.404
0.16
103
2.403
-0.16
51
2.403
-0.16
25
9.6
9.615
0.16
25
9.615
-0.16
12
—
—
—
19.2
19.231
0.16
12
—
—
—
—
—
—
57.6
62.500
8.51
3
—
—
—
—
—
—
115.2
125.000
8.51
1
—
—
—
—
—
—
DS39770B-page 234
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 17-3:
BAUD RATES FOR ASYNCHRONOUS MODES (CONTINUED)
SYNC = 0, BRGH = 0, BRG16 = 1
BAUD
RATE
(K)
FOSC = 40.000 MHz
Actual
Rate
(K)
%
Error
FOSC = 20.000 MHz
SPBRG
value
(decimal)
Actual
Rate
(K)
%
Error
FOSC = 10.000 MHz
(decimal)
Actual
Rate
(K)
SPBRG
value
%
Error
FOSC = 8.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
SPBRG
value
SPBRG
value
(decimal)
0.3
0.300
0.00
8332
0.300
0.02
4165
0.300
0.02
2082
0.300
-0.04
1.2
1.200
0.02
2082
1.200
-0.03
1041
1.200
-0.03
520
1.201
-0.16
1665
415
2.4
2.402
0.06
1040
2.399
-0.03
520
2.404
0.16
259
2.403
-0.16
207
9.6
9.615
0.16
259
9.615
0.16
129
9.615
0.16
64
9.615
-0.16
51
25
19.2
19.231
0.16
129
19.231
0.16
64
19.531
1.73
31
19.230
-0.16
57.6
58.140
0.94
42
56.818
-1.36
21
56.818
-1.36
10
55.555
3.55
8
115.2
113.636
-1.36
21
113.636
-1.36
10
125.000
8.51
4
—
—
—
SYNC = 0, BRGH = 0, BRG16 = 1
BAUD
RATE
(K)
FOSC = 4.000 MHz
Actual
Rate
(K)
%
Error
FOSC = 2.000 MHz
SPBRG
value
(decimal)
Actual
Rate
(K)
%
Error
FOSC = 1.000 MHz
SPBRG
value
(decimal)
Actual
Rate
(K)
%
Error
SPBRG
value
(decimal)
0.3
0.300
0.04
832
0.300
-0.16
415
0.300
-0.16
207
1.2
1.202
0.16
207
1.201
-0.16
103
1.201
-0.16
51
2.4
2.404
0.16
103
2.403
-0.16
51
2.403
-0.16
25
9.6
9.615
0.16
25
9.615
-0.16
12
—
—
—
19.2
19.231
0.16
12
—
—
—
—
—
—
57.6
62.500
8.51
3
—
—
—
—
—
—
115.2
125.000
8.51
1
—
—
—
—
—
—
SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1
BAUD
RATE
(K)
FOSC = 40.000 MHz
FOSC = 20.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
0.00
33332
0.300
0.00
8332
1.200
0.02
4165
Actual
Rate
(K)
%
Error
0.3
0.300
1.2
1.200
2.4
2.400
SPBRG
value
FOSC = 10.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
0.00
16665
0.300
0.02
4165
1.200
2.400
0.02
2082
2.402
SPBRG
value
FOSC = 8.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
0.00
8332
0.300
-0.01
6665
0.02
2082
1.200
-0.04
1665
0.06
1040
2.400
-0.04
832
SPBRG
value
SPBRG
value
(decimal)
9.6
9.606
0.06
1040
9.596
-0.03
520
9.615
0.16
259
9.615
-0.16
207
19.2
19.193
-0.03
520
19.231
0.16
259
19.231
0.16
129
19.230
-0.16
103
57.6
57.803
0.35
172
57.471
-0.22
86
58.140
0.94
42
57.142
0.79
34
115.2
114.943
-0.22
86
116.279
0.94
42
113.636
-1.36
21
117.647
-2.12
16
SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1
BAUD
RATE
(K)
FOSC = 4.000 MHz
FOSC = 2.000 MHz
FOSC = 1.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
3332
832
0.300
1.201
-0.04
-0.16
2.403
-0.16
207
9.615
-0.16
51
19.230
-0.16
25
16
55.555
3.55
8
—
—
Actual
Rate
(K)
%
Error
0.3
1.2
0.300
1.200
0.01
0.04
2.4
2.404
0.16
415
9.6
9.615
0.16
103
19.2
19.231
0.16
51
57.6
58.824
2.12
115.2
111.111
-3.55
SPBRG
value
© 2007 Microchip Technology Inc.
(decimal)
Actual
Rate
(K)
%
Error
1665
415
0.300
1.201
-0.04
-0.16
832
207
2.403
-0.16
103
9.615
-0.16
25
19.230
-0.16
12
8
—
—
—
—
—
—
—
SPBRG
value
Preliminary
SPBRG
value
(decimal)
DS39770B-page 235
PIC18F85J90 FAMILY
17.2.3
AUTO-BAUD RATE DETECT
The Enhanced USART module supports the automatic
detection and calibration of baud rate. This feature is
active only in Asynchronous mode and while the WUE
bit is clear.
The automatic baud rate measurement sequence
(Figure 17-1) begins whenever a Start bit is received
and the ABDEN bit is set. The calculation is
self-averaging.
While the ABD sequence takes place, the EUSART
state machine is held in Idle. The RC1IF interrupt is set
once the fifth rising edge on RX1 is detected. The value
in the RCREG1 needs to be read to clear the RC1IF
interrupt. The contents of RCREG1 should be
discarded.
Note 1: If the WUE bit is set with the ABDEN bit,
Auto-Baud Rate Detection will occur on
the byte following the Break character.
2: It is up to the user to determine that the
incoming character baud rate is within the
range of the selected BRG clock source.
Some combinations of oscillator frequency
and EUSART baud rates are not possible
due to bit error rates. Overall system
timing and communication baud rates
must be taken into consideration when
using the Auto-Baud Rate Detection
feature.
In the Auto-Baud Rate Detect (ABD) mode, the clock to
the BRG is reversed. Rather than the BRG clocking the
incoming RX1 signal, the RX1 signal is timing the BRG.
In ABD mode, the internal Baud Rate Generator is
used as a counter to time the bit period of the incoming
serial byte stream.
Once the ABDEN bit is set, the state machine will clear
the BRG and look for a Start bit. The Auto-Baud Rate
Detect must receive a byte with the value, 55h (ASCII
“U”, which is also the LIN bus Sync character), in order
to calculate the proper bit rate. The measurement is
taken over both a low and a high bit time in order to
minimize any effects caused by asymmetry of the
incoming signal. After a Start bit, the SPBRG1 begins
counting up, using the preselected clock source on the
first rising edge of RX1. After eight bits on the RX1 pin
or the fifth rising edge, an accumulated value totalling
the
proper
BRG
period
is
left
in
the
SPBRGH1:SPBRG1 register pair. Once the 5th edge is
seen (this should correspond to the Stop bit), the
ABDEN bit is automatically cleared.
If a rollover of the BRG occurs (an overflow from FFFFh
to 0000h), the event is trapped by the ABDOVF status bit
(BAUDCON1<7>). It is set in hardware by BRG rollovers
and can be set or cleared by the user in software. ABD
mode remains active after rollover events and the
ABDEN bit remains set (Figure 17-2).
While calibrating the baud rate period, the BRG registers are clocked at 1/8th the preconfigured clock rate.
Note that the BRG clock will be configured by the
BRG16 and BRGH bits. Independent of the BRG16 bit
setting, both the SPBRG1 and SPBRGH1 will be used
as a 16-bit counter. This allows the user to verify that
no carry occurred for 8-bit modes by checking for 00h
in the SPBRGH1 register. Refer to Table 17-4 for
counter clock rates to the BRG.
DS39770B-page 236
TABLE 17-4:
BRG COUNTER CLOCK
RATES
BRG16
BRGH
BRG Counter Clock
0
0
FOSC/512
0
1
FOSC/128
1
0
FOSC/128
1
1
FOSC/32
Note:
17.2.3.1
During the ABD sequence, SPBRG1 and
SPBRGH1 are both used as a 16-bit
counter, independent of the BRG16 setting.
ABD and EUSART Transmission
Since the BRG clock is reversed during ABD acquisition, the EUSART transmitter cannot be used during
ABD. This means that whenever the ABDEN bit is set,
TXREG1 cannot be written to. Users should also
ensure that ABDEN does not become set during a
transmit sequence. Failing to do this may result in
unpredictable EUSART operation.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 17-1:
BRG Value
AUTOMATIC BAUD RATE CALCULATION
XXXXh
0000h
001Ch
Start
RX1 pin
Edge #1
bit 1
bit 0
Edge #2
bit 3
bit 2
Edge #3
bit 5
bit 4
Edge #4
bit 7
bit 6
Edge #5
Stop bit
BRG Clock
Auto-Cleared
Set by User
ABDEN bit
RC1IF bit
(Interrupt)
Read
RCREG1
SPBRG1
XXXXh
1Ch
SPBRGH1
XXXXh
00h
Note: The ABD sequence requires the EUSART module to be configured in Asynchronous mode and WUE = 0.
FIGURE 17-2:
BRG OVERFLOW SEQUENCE
BRG Clock
ABDEN bit
RX1 pin
Start
bit 0
ABDOVF bit
FFFFh
BRG Value
XXXXh
© 2007 Microchip Technology Inc.
0000h
0000h
Preliminary
DS39770B-page 237
PIC18F85J90 FAMILY
17.3
EUSART Asynchronous Mode
Once the TXREG1 register transfers the data to the
TSR register (occurs in one TCY), the TXREG1 register
is empty and the TX1IF flag bit (PIR1<4>) is set. This
interrupt can be enabled or disabled by setting or clearing the interrupt enable bit, TX1IE (PIE1<4>). TX1IF
will be set regardless of the state of TX1IE; it cannot be
cleared in software. TX1IF is also not cleared immediately upon loading TXREG1, but becomes valid in the
second instruction cycle following the load instruction.
Polling TX1IF immediately following a load of TXREG1
will return invalid results.
The Asynchronous mode of operation is selected by
clearing the SYNC bit (TXSTA1<4>). In this mode, the
EUSART uses standard Non-Return-to-Zero (NRZ) format (one Start bit, eight or nine data bits and one Stop
bit). The most common data format is 8 bits. An on-chip
dedicated 8-bit/16-bit Baud Rate Generator can be
used to derive standard baud rate frequencies from the
oscillator.
The EUSART transmits and receives the LSb first. The
EUSART’s transmitter and receiver are functionally
independent, but use the same data format and baud
rate. The Baud Rate Generator produces a clock, either
x16 or x64 of the bit shift rate, depending on the BRGH
and BRG16 bits (TXSTA1<2> and BAUDCON1<3>).
Parity is not supported by the hardware but can be
implemented in software and stored as the 9th data bit.
While TX1IF indicates the status of the TXREG1 register, another bit, TRMT (TXSTA1<1>), shows the status
of the TSR register. TRMT is a read-only bit which is set
when the TSR register is empty. No interrupt logic is
tied to this bit so the user has to poll this bit in order to
determine if the TSR register is empty.
Note 1: The TSR register is not mapped in data
memory so it is not available to the user.
When operating in Asynchronous mode, the EUSART
module consists of the following important elements:
•
•
•
•
•
•
•
2: Flag bit, TX1IF, is set when enable bit,
TXEN, is set.
Baud Rate Generator
Sampling Circuit
Asynchronous Transmitter
Asynchronous Receiver
Auto-Wake-up on Sync Break Character
12-Bit Break Character Transmit
Auto-Baud Rate Detection
17.3.1
To set up an Asynchronous Transmission:
1.
2.
EUSART ASYNCHRONOUS
TRANSMITTER
3.
4.
The EUSART transmitter block diagram is shown in
Figure 17-3. The heart of the transmitter is the Transmit
(Serial) Shift register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG1. The TXREG1 register is loaded with data in
software. The TSR register is not loaded until the Stop
bit has been transmitted from the previous load. As
soon as the Stop bit is transmitted, the TSR is loaded
with new data from the TXREG1 register (if available).
FIGURE 17-3:
5.
6.
7.
8.
Initialize the SPBRGH1:SPBRG1 registers for
the appropriate baud rate. Set or clear the
BRGH and BRG16 bits, as required, to achieve
the desired baud rate.
Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
If interrupts are desired, set enable bit, TX1IE.
If 9-bit transmission is desired, set transmit bit,
TX9; can be used as address/data bit.
Enable the transmission by setting bit, TXEN,
which will also set bit, TX1IF.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Load data to the TXREG1 register (starts
transmission).
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
EUSART TRANSMIT BLOCK DIAGRAM
Data Bus
TX1IF
TXREG1 Register
TX1IE
8
MSb
(8)
LSb
• • •
Pin Buffer
and Control
0
TSR Register
TX1 pin
Interrupt
TXEN
Baud Rate CLK
TRMT
BRG16
SPBRGH1
SPBRG1
Baud Rate Generator
DS39770B-page 238
SPEN
TX9
TX9D
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 17-4:
ASYNCHRONOUS TRANSMISSION
Write to TXREG1
Word 1
BRG Output
(Shift Clock)
TX1 (pin)
Start bit
bit 0
bit 1
bit 7/8
Stop bit
Word 1
TX1IF bit
(Transmit Buffer
Reg. Empty Flag)
1 TCY
Word 1
Transmit Shift Reg
TRMT bit
(Transmit Shift
Reg. Empty Flag)
FIGURE 17-5:
ASYNCHRONOUS TRANSMISSION (BACK TO BACK)
Write to TXREG1
Word 2
Word 1
BRG Output
(Shift Clock)
TX1 (pin)
Start bit
bit 0
bit 1
1 TCY
TX1IF bit
(Interrupt Reg. Flag)
bit 7/8
Stop bit
Start bit
bit 0
Word 2
Word 1
1 TCY
Word 1
Transmit Shift Reg.
TRMT bit
(Transmit Shift
Reg. Empty Flag)
Note:
Word 2
Transmit Shift Reg.
This timing diagram shows two consecutive transmissions.
TABLE 17-5:
Name
REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
IPR1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
INTCON
RCSTA1
TXREG1
TXSTA1
BAUDCON1
GIE/GIEH PEIE/GIEL
EUSART Transmit Register
53
53
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
53
ABDOVF
RCMT
—
SCKP
BRG16
—
WUE
ABDEN
55
SPBRGH1
EUSART Baud Rate Generator Register High Byte
55
SPBRG1
EUSART Baud Rate Generator Register Low Byte
53
LATG
U2OD
U1OD
—
LATG4
LATG3
LATG2
LATG1
LATG0
54
Legend: — = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous transmission.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 239
PIC18F85J90 FAMILY
17.3.2
EUSART ASYNCHRONOUS
RECEIVER
17.3.3
The receiver block diagram is shown in Figure 17-6.
The data is received on the RX1 pin and drives the data
recovery block. The data recovery block is actually a
high-speed shifter operating at x16 times the baud rate,
whereas the main receive serial shifter operates at the
bit rate or at FOSC. This mode would typically be used
in RS-232 systems.
This mode would typically be used in RS-485 systems.
To set up an Asynchronous Reception with Address
Detect Enable:
1.
Initialize the SPBRGH1:SPBRG1 registers for
the appropriate baud rate. Set or clear the
BRGH and BRG16 bits, as required, to achieve
the desired baud rate.
2. Enable the asynchronous serial port by clearing
the SYNC bit and setting the SPEN bit.
3. If interrupts are required, set the RCEN bit and
select the desired priority level with the RC1IP
bit.
4. Set the RX9 bit to enable 9-bit reception.
5. Set the ADDEN bit to enable address detect.
6. Enable reception by setting the CREN bit.
7. The RC1IF bit will be set when reception is
complete. The interrupt will be Acknowledged if
the RC1IE and GIE bits are set.
8. Read the RCSTA1 register to determine if any
error occurred during reception, as well as read
bit 9 of data (if applicable).
9. Read RCREG1 to determine if the device is
being addressed.
10. If any error occurred, clear the CREN bit.
11. If the device has been addressed, clear the
ADDEN bit to allow all received data into the
receive buffer and interrupt the CPU.
To set up an Asynchronous Reception:
1.
Initialize the SPBRGH1:SPBRG1 registers for
the appropriate baud rate. Set or clear the
BRGH and BRG16 bits, as required, to achieve
the desired baud rate.
2. Enable the asynchronous serial port by clearing
bit SYNC and setting bit, SPEN.
3. If interrupts are desired, set enable bit, RC1IE.
4. If 9-bit reception is desired, set bit, RX9.
5. Enable the reception by setting bit, CREN.
6. Flag bit, RC1IF, will be set when reception is
complete and an interrupt will be generated if
enable bit, RC1IE, was set.
7. Read the RCSTA1 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
8. Read the 8-bit received data by reading the
RCREG1 register.
9. If any error occurred, clear the error by clearing
enable bit CREN.
10. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
FIGURE 17-6:
SETTING UP 9-BIT MODE WITH
ADDRESS DETECT
EUSART RECEIVE BLOCK DIAGRAM
CREN
OERR
FERR
x64 Baud Rate CLK
BRG16
SPBRGH1
SPBRG1
Baud Rate Generator
÷ 64
or
÷ 16
or
÷4
RSR Register
MSb
Stop
(8)
7
• • •
LSb
1
0
Start
RX9
Pin Buffer
and Control
Data
Recovery
RX1
RX9D
RCREG1 Register
FIFO
SPEN
8
Interrupt
RC1IF
Data Bus
RC1IE
DS39770B-page 240
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 17-7:
ASYNCHRONOUS RECEPTION
Start
bit
RX1 (pin)
bit 0
bit 1
bit 7/8 Stop
bit
Start
bit
bit 0
Rcv Shift Reg
Rcv Buffer Reg
Stop
bit
Start
bit
bit 7/8
Stop
bit
Word 2
RCREG1
Word 1
RCREG1
RCREG1
Read Rcv
Buffer Reg
bit 7/8
RC1IF
(Interrupt Flag)
OERR bit
CREN bit
Note:
This timing diagram shows three words appearing on the RX1 input. The RCREG1 (Receive Buffer register) is read after the third word
causing the OERR (Overrun) bit to be set.
TABLE 17-6:
Name
INTCON
REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION
Bit 7
Bit 6
Bit 5
GIE/GIEH PEIE/GIEL TMR0IE
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
53
IPR1
RCSTA1
RCREG1
TXSTA1
EUSART Receive Register
53
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
53
RCMT
—
SCKP
BRG16
—
WUE
ABDEN
55
BAUDCON1
ABDOVF
SPBRGH1
EUSART Baud Rate Generator Register High Byte
55
SPBRG1
EUSART Baud Rate Generator Register Low Byte
53
Legend: — = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous reception.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 241
PIC18F85J90 FAMILY
17.3.4
AUTO-WAKE-UP ON SYNC BREAK
CHARACTER
During Sleep mode, all clocks to the EUSART are
suspended. Because of this, the Baud Rate Generator
is inactive and a proper byte reception cannot be performed. The auto-wake-up feature allows the controller
to wake-up, due to activity on the RX1/DT1 line, while
the EUSART is operating in Asynchronous mode.
The auto-wake-up feature is enabled by setting the
WUE bit (BAUDCON<1>). Once set, the typical receive
sequence on RX1/DT1 is disabled and the EUSART
remains in an Idle state, monitoring for a wake-up event
independent of the CPU mode. A wake-up event
consists of a high-to-low transition on the RX1/DT1
line. (This coincides with the start of a Sync Break or a
Wake-up Signal character for the LIN protocol.)
Following a wake-up event, the module generates an
RC1IF interrupt. The interrupt is generated synchronously to the Q clocks in normal operating modes
(Figure 17-8) and asynchronously, if the device is in
Sleep mode (Figure 17-9). The interrupt condition is
cleared by reading the RCREG1 register.
The WUE bit is automatically cleared once a low-to-high
transition is observed on the RX1 line following the
wake-up event. At this point, the EUSART module is in
Idle mode and returns to normal operation. This signals
to the user that the Sync Break event is over.
17.3.4.1
Special Considerations Using
Auto-Wake-up
Since auto-wake-up functions by sensing rising edge
transitions on RX1/DT1, information with any state
changes before the Stop bit may signal a false
FIGURE 17-8:
end-of-character and cause data or framing errors.
Therefore, to work properly, the initial character in the
transmission must be all ‘0’s. This can be 00h (8 bytes)
for standard RS-232 devices, or 000h (12 bits) for LIN
bus.
Oscillator start-up time must also be considered,
especially in applications using oscillators with longer
start-up intervals (i.e., XT or HS mode). The Sync
Break (or Wake-up Signal) character must be of
sufficient length and be followed by a sufficient interval
to allow enough time for the selected oscillator to start
and provide proper initialization of the EUSART.
17.3.4.2
Special Considerations Using
the WUE Bit
The timing of WUE and RC1IF events may cause some
confusion when it comes to determining the validity of
received data. As noted, setting the WUE bit places the
EUSART in an Idle mode. The wake-up event causes
a receive interrupt by setting the RC1IF bit. The WUE
bit is cleared after this when a rising edge is seen on
RX1/DT1. The interrupt condition is then cleared by
reading the RCREG1 register. Ordinarily, the data in
RCREG1 will be dummy data and should be discarded.
The fact that the WUE bit has been cleared (or is still
set) and the RC1IF flag is set should not be used as an
indicator of the integrity of the data in RCREG1. Users
should consider implementing a parallel method in
firmware to verify received data integrity.
To assure that no actual data is lost, check the RCMT
bit to verify that a receive operation is not in process. If
a receive operation is not occurring, the WUE bit may
then be set just prior to entering the Sleep mode.
AUTO-WAKE-UP BIT (WUE) TIMINGS DURING NORMAL OPERATION
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
Bit set by user
Auto-Cleared
WUE bit(1)
RX1/DT1 Line
RC1IF
Cleared due to user read of RCREG1
Note 1:
The EUSART remains in Idle while the WUE bit is set.
FIGURE 17-9:
AUTO-WAKE-UP BIT (WUE) TIMINGS DURING SLEEP
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Q1
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
Bit set by user
Auto-Cleared
WUE bit(2)
RX1/DT1 Line
Note 1
RC1IF
SLEEP Command Executed
Note 1:
2:
Sleep Ends
Cleared due to user read of RCREG1
If the wake-up event requires long oscillator warm-up time, the auto-clear of the WUE bit can occur while the stposc signal is still active.
This sequence should not depend on the presence of Q clocks.
The EUSART remains in Idle while the WUE bit is set.
DS39770B-page 242
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
17.3.5
BREAK CHARACTER SEQUENCE
The Enhanced USART module has the capability of
sending the special Break character sequences that are
required by the LIN bus standard. The Break character
transmit consists of a Start bit, followed by twelve ‘0’ bits
and a Stop bit. The Frame Break character is sent
whenever the SENDB and TXEN bits (TXSTA<3> and
TXSTA<5>) are set while the Transmit Shift register is
loaded with data. Note that the value of data written to
TXREG1 will be ignored and all ‘0’s will be transmitted.
The SENDB bit is automatically reset by hardware after
the corresponding Stop bit is sent. This allows the user
to preload the transmit FIFO with the next transmit byte
following the Break character (typically, the Sync
character in the LIN specification).
Note that the data value written to the TXREG1 for the
Break character is ignored. The write simply serves the
purpose of initiating the proper sequence.
The TRMT bit indicates when the transmit operation is
active or Idle, just as it does during normal transmission. See Figure 17-10 for the timing of the Break
character sequence.
17.3.5.1
Break and Sync Transmit Sequence
The following sequence will send a message frame
header made up of a Break, followed by an Auto-Baud
Sync byte. This sequence is typical of a LIN bus master.
1.
2.
3.
4.
5.
Configure the EUSART for the desired mode.
Set the TXEN and SENDB bits to set up the
Break character.
Load the TXREG1 with a dummy character to
initiate transmission (the value is ignored).
Write ‘55h’ to TXREG1 to load the Sync
character into the transmit FIFO buffer.
After the Break has been sent, the SENDB bit is
reset by hardware. The Sync character now
transmits in the preconfigured mode.
When the TXREG1 becomes empty, as indicated by the
TX1IF, the next data byte can be written to TXREG1.
17.3.6
RECEIVING A BREAK CHARACTER
The Enhanced USART module can receive a Break
character in two ways.
The first method forces configuration of the baud rate
at a frequency of 9/13 the typical speed. This allows for
the Stop bit transition to be at the correct sampling
location (13 bits for Break versus Start bit and 8 data
bits for typical data).
The second method uses the auto-wake-up feature
described in Section 17.3.4 “Auto-Wake-up On Sync
Break Character”. By enabling this feature, the
EUSART will sample the next two transitions on
RX1/DT1, cause an RC1IF interrupt and receive the
next data byte followed by another interrupt.
Note that following a Break character, the user will
typically want to enable the Auto-Baud Rate Detect
feature. For both methods, the user can set the ABD bit
once the TX1IF interrupt is observed.
FIGURE 17-10:
Write to TXREG1
SEND BREAK CHARACTER SEQUENCE
Dummy Write
BRG Output
(Shift Clock)
TX1 (pin)
Start bit
bit 0
bit 1
bit 11
Stop bit
Break
TX1IF bit
(Transmit Buffer
Reg. Empty Flag)
TRMT bit
(Transmit Shift
Reg. Empty Flag)
SENDB sampled here
Auto-Cleared
SENDB
(Transmit Shift
Reg. Empty Flag)
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 243
PIC18F85J90 FAMILY
17.4
EUSART Synchronous
Master Mode
Once the TXREG1 register transfers the data to the
TSR register (occurs in one TCYCLE), the TXREG1 is
empty and the TX1IF flag bit (PIR1<4>) is set. The
interrupt can be enabled or disabled by setting or clearing the interrupt enable bit, TX1IE (PIE1<4>). TX1IF is
set regardless of the state of enable bit TX1IE; it cannot
be cleared in software. It will reset only when new data
is loaded into the TXREG1 register.
The Synchronous Master mode is entered by setting
the CSRC bit (TXSTA<7>). In this mode, the data is
transmitted in a half-duplex manner (i.e., transmission
and reception do not occur at the same time). When
transmitting data, the reception is inhibited and vice
versa. Synchronous mode is entered by setting bit
SYNC (TXSTA<4>). In addition, enable bit, SPEN
(RCSTA1<7>), is set in order to configure the TX1 and
RX1 pins to CK1 (clock) and DT1 (data) lines,
respectively.
While flag bit TX1IF indicates the status of the TXREG1
register, another bit, TRMT (TXSTA<1>), shows the
status of the TSR register. TRMT is a read-only bit which
is set when the TSR is empty. No interrupt logic is tied to
this bit so the user has to poll this bit in order to determine if the TSR register is empty. The TSR is not
mapped in data memory so it is not available to the user.
The Master mode indicates that the processor transmits the master clock on the CK1 line. Clock polarity is
selected with the SCKP bit (BAUDCON<4>). Setting
SCKP sets the Idle state on CK1 as high, while clearing
the bit sets the Idle state as low. This option is provided
to support Microwire devices with this module.
17.4.1
To set up a Synchronous Master Transmission:
1.
EUSART SYNCHRONOUS MASTER
TRANSMISSION
2.
The EUSART transmitter block diagram is shown in
Figure 17-3. The heart of the transmitter is the Transmit
(Serial) Shift register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG1. The TXREG1 register is loaded with data in
software. The TSR register is not loaded until the last
bit has been transmitted from the previous load. As
soon as the last bit is transmitted, the TSR is loaded
with new data from the TXREG1 (if available).
FIGURE 17-11:
3.
4.
5.
6.
7.
8.
Initialize the SPBRGH1:SPBRG1 registers for
the appropriate baud rate. Set or clear the
BRG16 bit, as required, to achieve the desired
baud rate.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
If interrupts are desired, set enable bit, TX1IE.
If 9-bit transmission is desired, set bit, TX9.
Enable the transmission by setting bit, TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the
TXREG1 register.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
SYNCHRONOUS TRANSMISSION
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RC7/RX1/DT1
pin
bit 0
bit 1
bit 2
Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit 7
bit 0
bit 1
bit 7
Word 2
Word 1
RC6/TX1/CK1 pin
(SCKP = 0)
RC6/TX1/CK1 pin
(SCKP = 1)
Write to
TXREG1 Reg
Write Word 1
Write Word 2
TX1IF bit
(Interrupt Flag)
TRMT bit
TXEN bit
Note:
‘1’
‘1’
Sync Master mode, SPBRG1 = 0; continuous transmission of two 8-bit words.
DS39770B-page 244
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 17-12:
SYNCHRONOUS TRANSMISSION (THROUGH TXEN)
RC7/RX1/DT1 pin
bit 0
bit 2
bit 1
bit 6
bit 7
RC6/TX1/CK1 pin
Write to
TXREG1 Reg
TX1IF bit
TRMT bit
TXEN bit
TABLE 17-7:
Name
INTCON
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION
Bit 7
Bit 6
Bit 5
GIE/GIEH PEIE/GIEL TMR0IE
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
53
IPR1
RCSTA1
TXREG1
TXSTA1
EUSART Transmit Register
CSRC
BAUDCON1 ABDOVF
53
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
53
RCMT
—
SCKP
BRG16
—
WUE
ABDEN
55
SPBRGH1
EUSART Baud Rate Generator Register High Byte
SPBRG1
EUSART Baud Rate Generator Register Low Byte
LATG
U2OD
U1OD
—
LATG4
LATG3
55
53
LATG2
LATG1
LATG0
54
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master transmission.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 245
PIC18F85J90 FAMILY
17.4.2
EUSART SYNCHRONOUS
MASTER RECEPTION
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA1<5>), or the Continuous Receive
Enable bit, CREN (RCSTA1<4>). Data is sampled on
the RX1 pin on the falling edge of the clock.
If enable bit SREN is set, only a single word is received.
If enable bit CREN is set, the reception is continuous
until CREN is cleared. If both bits are set, then CREN
takes precedence.
To set up a Synchronous Master Reception:
1.
2.
Initialize the SPBRGH1:SPBRG1 registers for the
appropriate baud rate. Set or clear the BRG16 bit,
as required, to achieve the desired baud rate.
Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
FIGURE 17-13:
3.
4.
5.
6.
Ensure bits, CREN and SREN, are clear.
If interrupts are desired, set enable bit, RC1IE.
If 9-bit reception is desired, set bit, RX9.
If a single reception is required, set bit, SREN.
For continuous reception, set bit, CREN.
7. Interrupt flag bit, RC1IF, will be set when reception is complete and an interrupt will be generated
if the enable bit, RC1IE, was set.
8. Read the RCSTA1 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
9. Read the 8-bit received data by reading the
RCREG1 register.
10. If any error occurred, clear the error by clearing
bit, CREN.
11. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RC7/RX1/DT1
pin
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
RC6/TX1/CK1 pin
(SCKP = 0)
RC6/TX1/CK1 pin
(SCKP = 1)
Write to
SREN bit
SREN bit
CREN bit ‘0’
‘0’
RC1IF bit
(Interrupt)
Read
RCREG1
Note:
Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.
TABLE 17-8:
Name
INTCON
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Bit 7
Bit 6
GIE/GIEH PEIE/GIEL
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
53
IPR1
RCSTA1
RCREG1
TXSTA1
EUSART Receive Register
CSRC
BAUDCON1 ABDOVF
53
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
53
RCMT
—
SCKP
BRG16
—
WUE
ABDEN
55
SPBRGH1
EUSART Baud Rate Generator Register High Byte
55
SPBRG1
EUSART Baud Rate Generator Register Low Byte
53
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
DS39770B-page 246
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
17.5
EUSART Synchronous Slave Mode
Synchronous Slave mode is entered by clearing bit
CSRC (TXSTA<7>). This mode differs from the
Synchronous Master mode in that the shift clock is
supplied externally at the CK1 pin (instead of being
supplied internally in Master mode). This allows the
device to transfer or receive data while in any
low-power mode.
17.5.1
EUSART SYNCHRONOUS SLAVE
TRANSMIT
To set up a Synchronous Slave Transmission:
1.
2.
3.
4.
5.
6.
The operation of the Synchronous Master and Slave
modes are identical except in the case of the Sleep
mode.
7.
8.
If two words are written to the TXREG1 and then the
SLEEP instruction is executed, the following will occur:
a)
b)
c)
d)
e)
Enable the synchronous slave serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
Clear bits CREN and SREN.
If interrupts are desired, set enable bit, TX1IE.
If 9-bit transmission is desired, set bit, TX9.
Enable the transmission by setting enable bit,
TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the
TXREG1 register.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
The first word will immediately transfer to the
TSR register and transmit.
The second word will remain in the TXREG1
register.
Flag bit, TX1IF, will not be set.
When the first word has been shifted out of TSR,
the TXREG1 register will transfer the second
word to the TSR and flag bit, TX1IF, will now be
set.
If enable bit, TX1IE, is set, the interrupt will wake
the chip from Sleep. If the global interrupt is
enabled, the program will branch to the interrupt
vector.
TABLE 17-9:
Name
REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
IPR1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
53
INTCON
RCSTA1
TXREG1
TXSTA1
GIE/GIEH PEIE/GIEL
EUSART Transmit Register
CSRC
BAUDCON1 ABDOVF
53
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
53
RCMT
—
SCKP
BRG16
—
WUE
ABDEN
55
SPBRGH1
EUSART Baud Rate Generator Register High Byte
55
SPBRG1
EUSART Baud Rate Generator Register Low Byte
53
LATG
U2OD
U1OD
—
LATG4
LATG3
LATG2
LATG1
LATG0
54
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave transmission.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 247
PIC18F85J90 FAMILY
17.5.2
EUSART SYNCHRONOUS SLAVE
RECEPTION
To set up a Synchronous Slave Reception:
1.
The operation of the Synchronous Master and Slave
modes is identical except in the case of Sleep or any
Idle mode, and bit SREN, which is a “don’t care” in
Slave mode.
If receive is enabled by setting the CREN bit prior to
entering Sleep or any Idle mode, then a word may be
received while in this low-power mode. Once the word
is received, the RSR register will transfer the data to the
RCREG1 register; if the RC1IE enable bit is set, the
interrupt generated will wake the chip from the
low-power mode. If the global interrupt is enabled, the
program will branch to the interrupt vector.
2.
3.
4.
5.
6.
7.
8.
9.
Enable the synchronous master serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
If interrupts are desired, set enable bit, RC1IE.
If 9-bit reception is desired, set bit, RX9.
To enable reception, set enable bit, CREN.
Flag bit, RC1IF, will be set when reception is
complete. An interrupt will be generated if
enable bit, RC1IE, was set.
Read the RCSTA1 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG1 register.
If any error occurred, clear the error by clearing
bit, CREN.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
TABLE 17-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
Name
INTCON
Bit 7
Bit 6
Bit 5
GIE/GIEH PEIE/GIEL TMR0IE
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
IPR1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
RCSTA1
RCREG1
TXSTA1
EUSART Receive Register
CSRC
BAUDCON1 ABDOVF
53
53
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
53
RCMT
—
SCKP
BRG16
—
WUE
ABDEN
55
SPBRGH1
EUSART Baud Rate Generator Register High Byte
55
SPBRG1
EUSART Baud Rate Generator Register Low Byte
53
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.
DS39770B-page 248
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
18.0
ADDRESSABLE UNIVERSAL
SYNCHRONOUS
ASYNCHRONOUS RECEIVER
TRANSMITTER (AUSART)
The Addressable Universal Synchronous Asynchronous Receiver Transmitter (AUSART) module is very
similar in function to the Enhanced USART module,
discussed in the previous chapter. It is provided as an
additional channel for serial communication with
external devices, for those situations that do not require
auto-baud detection or LIN bus support.
Note:
The AUSART control will automatically
reconfigure the pin from input to output as
needed.
The driver for the TX2 output pin can also be optionally
configured as an open-drain output. This feature allows
the voltage level on the pin to be pulled to a higher level
through an external pull-up resistor, and allows the
output to communicate with external circuits without the
need for additional level shifters.
The open-drain output option is controlled by the U2OD
bit (LATG<7>). Setting the bit configures the pin for
open-drain operation.
The AUSART can be configured in the following modes:
18.1
• Asynchronous (full-duplex)
• Synchronous – Master (half-duplex)
• Synchronous – Slave (half-duplex)
The pins of the AUSART module are multiplexed with
the functions of PORTG (RG1/TX2/CK2 and
RG2/RX2/DT2/VLCAP1, respectively). In order to
configure these pins as an AUSART:
Control Registers
The operation of the Addressable USART module is
controlled through two registers, TXSTA2 and
RXSTA2. These are detailed in Register 18-1 and
Register 18-2, respectively.
• bit SPEN (RCSTA2<7>) must be set (= 1)
• bit TRISG<2> must be set (= 1)
• bit TRISG<1> must be cleared (= 0) for
Asynchronous and Synchronous Master modes
• bit TRISG<1> must be set (= 1) for Synchronous
Slave mode
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 249
PIC18F85J90 FAMILY
REGISTER 18-1:
TXSTA2: AUSART TRANSMIT STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R-1
R/W-0
CSRC
TX9
TXEN(1)
SYNC
—
BRGH
TRMT
TX9D
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
CSRC: Clock Source Select bit
Asynchronous mode:
Don’t care.
Synchronous mode:
1 = Master mode (clock generated internally from BRG)
0 = Slave mode (clock from external source)
bit 6
TX9: 9-Bit Transmit Enable bit
1 = Selects 9-bit transmission
0 = Selects 8-bit transmission
bit 5
TXEN: Transmit Enable bit(1)
1 = Transmit enabled
0 = Transmit disabled
bit 4
SYNC: AUSART Mode Select bit
1 = Synchronous mode
0 = Asynchronous mode
bit 3
Unimplemented: Read as ‘0’
bit 2
BRGH: High Baud Rate Select bit
Asynchronous mode:
1 = High speed
0 = Low speed
Synchronous mode:
Unused in this mode.
bit 1
TRMT: Transmit Shift Register Status bit
1 = TSR empty
0 = TSR full
bit 0
TX9D: 9th bit of Transmit Data
Can be address/data bit or a parity bit.
Note 1:
x = Bit is unknown
SREN/CREN overrides TXEN in Sync mode.
DS39770B-page 250
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 18-2:
RCSTA2: AUSART RECEIVE STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R-0
R-0
R-x
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
SPEN: Serial Port Enable bit
1 = Serial port enabled (configures RX2/DT2 and TX2/CK2 pins as serial port pins)
0 = Serial port disabled (held in Reset)
bit 6
RX9: 9-Bit Receive Enable bit
1 = Selects 9-bit reception
0 = Selects 8-bit reception
bit 5
SREN: Single Receive Enable bit
Asynchronous mode:
Don’t care.
Synchronous mode – Master:
1 = Enables single receive
0 = Disables single receive
This bit is cleared after reception is complete.
Synchronous mode – Slave:
Don’t care.
bit 4
CREN: Continuous Receive Enable bit
Asynchronous mode:
1 = Enables receiver
0 = Disables receiver
Synchronous mode:
1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN)
0 = Disables continuous receive
bit 3
ADDEN: Address Detect Enable bit
Asynchronous mode 9-bit (RX9 = 1):
1 = Enables address detection, enables interrupt and loads the receive buffer when RSR<8> is set
0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit
Asynchronous mode 9-bit (RX9 = 0):
Don’t care.
bit 2
FERR: Framing Error bit
1 = Framing error (can be updated by reading RCREG2 register and receiving next valid byte)
0 = No framing error
bit 1
OERR: Overrun Error bit
1 = Overrun error (can be cleared by clearing bit CREN)
0 = No overrun error
bit 0
RX9D: 9th bit of Received Data
This can be address/data bit or a parity bit and must be calculated by user firmware.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 251
PIC18F85J90 FAMILY
18.2
AUSART Baud Rate Generator
(BRG)
The BRG is a dedicated, 8-bit generator that supports
both the Asynchronous and Synchronous modes of the
AUSART.
The SPBRG2 register controls the period of a
free-running timer. In Asynchronous mode, bit BRGH
(TXSTA<2>) also controls the baud rate. In Synchronous mode, BRGH is ignored. Table 18-1 shows the
formula for computation of the baud rate for different
AUSART modes, which only apply in Master mode
(internally generated clock).
Given the desired baud rate and FOSC, the nearest
integer value for the SPBRG2 register can be calculated using the formulas in Table 18-1. From this, the
error in baud rate can be determined. An example
calculation is shown in Example 18-1. Typical baud
rates and error values for the various Asynchronous
modes are shown in Table 18-2. It may be advantageous to use the high baud rate (BRGH = 1) to reduce
the baud rate error, or achieve a slow baud rate for a
fast oscillator frequency.
TABLE 18-1:
Writing a new value to the SPBRG2 register causes the
BRG timer to be reset (or cleared). This ensures the
BRG does not wait for a timer overflow before outputting
the new baud rate.
18.2.1
OPERATION IN POWER-MANAGED
MODES
The device clock is used to generate the desired baud
rate. When one of the power-managed modes is
entered, the new clock source may be operating at a
different frequency. This may require an adjustment to
the value in the SPBRG2 register.
18.2.2
SAMPLING
The data on the RX2 pin is sampled three times by a
majority detect circuit to determine if a high or a low
level is present at the RX2 pin.
BAUD RATE FORMULAS
Configuration Bits
BRG/AUSART Mode
Baud Rate Formula
0
Asynchronous
FOSC/[64 (n + 1)]
1
Asynchronous
FOSC/[16 (n + 1)]
x
Synchronous
FOSC/[4 (n + 1)]
SYNC
BRGH
0
0
1
Legend: x = Don’t care, n = Value of SPBRG2 register
EXAMPLE 18-1:
CALCULATING BAUD RATE ERROR
For a device with FOSC of 16 MHz, desired baud rate of 9600, Asynchronous mode, BRGH = 0:
Desired Baud Rate
= FOSC/(64 ([SPBRG2] + 1))
Solving for SPBRG2:
X
= ((FOSC/Desired Baud Rate)/64) – 1
= ((16000000/9600)/64) – 1
= [25.042] = 25
Calculated Baud Rate = 16000000/(64 (25 + 1))
= 9615
Error
= (Calculated Baud Rate – Desired Baud Rate)/Desired Baud Rate
= (9615 – 9600)/9600 = 0.16%
TABLE 18-2:
Name
REGISTERS ASSOCIATED WITH THE BAUD RATE GENERATOR
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values on
Page
TXSTA2
CSRC
TX9
TXEN
SYNC
—
BRGH
TRMT
TX9D
56
RCSTA2
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
56
SPBRG2
AUSART Baud Rate Generator Register
56
Legend: Shaded cells are not used by the BRG.
DS39770B-page 252
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 18-3:
BAUD RATES FOR ASYNCHRONOUS MODES
BRGH = 0
FOSC = 40.000 MHz
FOSC = 20.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
1.221
—
1.73
2.404
9.766
19.531
10
4
BAUD
RATE
(K)
Actual
Rate
(K)
%
Error
0.3
1.2
—
—
—
—
2.4
2.441
1.73
255
9.6
9.615
0.16
64
19.2
19.531
1.73
31
57.6
56.818
-1.36
115.2
125.000
8.51
SPBRG
value
FOSC = 10.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
255
—
1.202
—
0.16
0.16
129
2.404
1.73
31
9.766
1.73
15
62.500
8.51
104.167
-9.58
FOSC = 8.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
129
—
1.201
—
-0.16
—
103
0.16
64
2.403
-0.16
51
1.73
15
9.615
-0.16
12
19.531
1.73
7
—
—
—
4
52.083
-9.58
2
—
—
—
2
78.125
-32.18
1
—
—
—
SPBRG
value
%
Error
SPBRG
value
SPBRG
value
SPBRG
value
(decimal)
BRGH = 0
FOSC = 4.000 MHz
FOSC = 2.000 MHz
FOSC = 1.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
(decimal)
Actual
Rate
(K)
207
0.300
-0.16
103
0.300
-0.16
51
0.16
51
1.201
-0.16
25
1.201
-0.16
12
2.404
0.16
25
2.403
-0.16
12
—
—
—
8.929
-6.99
6
—
—
—
—
—
—
19.2
20.833
8.51
2
—
—
—
—
—
—
57.6
62.500
8.51
0
—
—
—
—
—
—
115.2
62.500
-45.75
0
—
—
—
—
—
—
BAUD
RATE
(K)
Actual
Rate
(K)
%
Error
0.3
0.300
0.16
1.2
1.202
2.4
9.6
SPBRG
value
SPBRG
value
(decimal)
BRGH = 1
BAUD
RATE
(K)
FOSC = 40.000 MHz
FOSC = 20.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
—
—
—
—
—
Actual
Rate
(K)
%
Error
0.3
—
1.2
—
2.4
SPBRG
value
FOSC = 10.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
—
—
—
—
—
SPBRG
value
FOSC = 8.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
—
—
—
—
—
2.441
1.73
255
2.403
-0.16
207
SPBRG
value
SPBRG
value
(decimal)
—
9.6
9.766
1.73
255
9.615
0.16
129
9.615
0.16
64
9.615
-0.16
51
19.2
19.231
0.16
129
19.231
0.16
64
19.531
1.73
31
19.230
-0.16
25
57.6
58.140
0.94
42
56.818
-1.36
21
56.818
-1.36
10
55.555
3.55
8
115.2
113.636
-1.36
21
113.636
-1.36
10
125.000
8.51
4
—
—
—
BRGH = 1
BAUD
RATE
(K)
FOSC = 4.000 MHz
Actual
Rate
(K)
%
Error
FOSC = 2.000 MHz
SPBRG
value
(decimal)
Actual
Rate
(K)
%
Error
SPBRG
value
(decimal)
FOSC = 1.000 MHz
Actual
Rate
(K)
%
Error
SPBRG
value
(decimal)
0.3
—
—
—
—
—
—
0.300
-0.16
207
1.2
1.202
0.16
207
1.201
-0.16
103
1.201
-0.16
51
2.4
2.404
0.16
103
2.403
-0.16
51
2.403
-0.16
25
9.6
9.615
0.16
25
9.615
-0.16
12
—
—
—
19.2
19.231
0.16
12
—
—
—
—
—
—
57.6
62.500
8.51
3
—
—
—
—
—
—
115.2
125.000
8.51
1
—
—
—
—
—
—
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 253
PIC18F85J90 FAMILY
18.3
Once the TXREG2 register transfers the data to the
TSR register (occurs in one TCY), the TXREG2 register
is empty and the TX2IF flag bit (PIR3<4>) is set. This
interrupt can be enabled or disabled by setting or
clearing the interrupt enable bit, TX2IE (PIE3<4>).
TX2IF will be set regardless of the state of TX2IE; it
cannot be cleared in software. TX2IF is also not
cleared immediately upon loading TXREG2, but
becomes valid in the second instruction cycle following
the load instruction. Polling TX2IF immediately
following a load of TXREG2 will return invalid results.
AUSART Asynchronous Mode
The Asynchronous mode of operation is selected by
clearing the SYNC bit (TXSTA2<4>). In this mode, the
AUSART uses standard Non-Return-to-Zero (NRZ)
format (one Start bit, eight or nine data bits and one
Stop bit). The most common data format is 8 bits. An
on-chip, dedicated, 8-bit Baud Rate Generator can be
used to derive standard baud rate frequencies from the
oscillator.
The AUSART transmits and receives the LSb first. The
AUSART’s transmitter and receiver are functionally
independent but use the same data format and baud
rate. The Baud Rate Generator produces a clock,
either x16 or x64 of the bit shift rate, depending on the
BRGH bit (TXSTA2<2>). Parity is not supported by the
hardware but can be implemented in software and
stored as the 9th data bit.
While TX2IF indicates the status of the TXREG2
register, another bit, TRMT (TXSTA2<1>), shows the
status of the TSR register. TRMT is a read-only bit
which is set when the TSR register is empty. No interrupt logic is tied to this bit so the user has to poll this bit
in order to determine if the TSR register is empty.
Note 1: The TSR register is not mapped in data
memory so it is not available to the user.
When operating in Asynchronous mode, the AUSART
module consists of the following important elements:
•
•
•
•
2: Flag bit, TX2IF, is set when enable bit,
TXEN, is set.
Baud Rate Generator
Sampling Circuit
Asynchronous Transmitter
Asynchronous Receiver
18.3.1
To set up an Asynchronous Transmission:
1.
AUSART ASYNCHRONOUS
TRANSMITTER
2.
The AUSART transmitter block diagram is shown in
Figure 18-1. The heart of the transmitter is the Transmit
(Serial) Shift register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG2. The TXREG2 register is loaded with data in
software. The TSR register is not loaded until the Stop
bit has been transmitted from the previous load. As
soon as the Stop bit is transmitted, the TSR is loaded
with new data from the TXREG2 register (if available).
3.
4.
5.
6.
7.
8.
FIGURE 18-1:
Initialize the SPBRG2 register for the appropriate
baud rate. Set or clear the BRGH bit, as required,
to achieve the desired baud rate.
Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
If interrupts are desired, set enable bit, TX2IE.
If 9-bit transmission is desired, set transmit bit,
TX9. Can be used as address/data bit.
Enable the transmission by setting bit, TXEN,
which will also set bit, TX2IF.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit, TX9D.
Load data to the TXREG2 register (starts
transmission).
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
AUSART TRANSMIT BLOCK DIAGRAM
Data Bus
TX2IF
TXREG2 Register
TX2IE
8
MSb
(8)
LSb
• • •
Pin Buffer
and Control
0
TSR Register
TX2 pin
Interrupt
TXEN
Baud Rate CLK
TRMT
SPBRG2
SPEN
TX9
Baud Rate Generator
TX9D
DS39770B-page 254
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 18-2:
ASYNCHRONOUS TRANSMISSION
Write to TXREG2
Word 1
BRG Output
(Shift Clock)
TX2 (pin)
Start bit
bit 0
bit 1
bit 7/8
Stop bit
Word 1
TX2IF bit
(Transmit Buffer
Reg. Empty Flag)
1 TCY
Word 1
Transmit Shift Reg
TRMT bit
(Transmit Shift
Reg. Empty Flag)
FIGURE 18-3:
ASYNCHRONOUS TRANSMISSION (BACK TO BACK)
Write to TXREG2
Word 2
Word 1
BRG Output
(Shift Clock)
TX2 (pin)
Start bit
bit 0
bit 1
1 TCY
TX2IF bit
(Interrupt Reg. Flag)
bit 7/8
Stop bit
Start bit
bit 0
Word 2
Word 1
1 TCY
Word 1
Transmit Shift Reg.
TRMT bit
(Transmit Shift
Reg. Empty Flag)
Note:
Word 2
Transmit Shift Reg.
This timing diagram shows two consecutive transmissions.
TABLE 18-4:
Name
INTCON
REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION
Bit 7
Bit 6
GIE/GIEH PEIE/GIEL
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR3
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
54
PIE3
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
54
IPR3
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
RCSTA2
TXREG2
TXSTA2
SPBRG2
LATG
AUSART Transmit Register
CSRC
TX9
TXEN
SYNC
—
BRGH
TRMT
TX9D
AUSART Baud Rate Generator Register
U2OD
U1OD
56
56
—
LATG4
56
56
LATG3
LATG2
LATG1
LATG0
54
Legend: — = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous transmission.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 255
PIC18F85J90 FAMILY
18.3.2
AUSART ASYNCHRONOUS
RECEIVER
18.3.3
The receiver block diagram is shown in Figure 18-4.
The data is received on the RX2 pin and drives the data
recovery block. The data recovery block is actually a
high-speed shifter operating at x16 times the baud rate,
whereas the main receive serial shifter operates at the
bit rate or at FOSC. This mode would typically be used
in RS-232 systems.
This mode would typically be used in RS-485 systems.
To set up an Asynchronous Reception with Address
Detect Enable:
1.
Initialize the SPBRG2 register for the appropriate
baud rate. Set or clear the BRGH and BRG16
bits, as required, to achieve the desired baud
rate.
2. Enable the asynchronous serial port by clearing
the SYNC bit and setting the SPEN bit.
3. If interrupts are required, set the RCEN bit and
select the desired priority level with the RC2IP
bit.
4. Set the RX9 bit to enable 9-bit reception.
5. Set the ADDEN bit to enable address detect.
6. Enable reception by setting the CREN bit.
7. The RC2IF bit will be set when reception is
complete. The interrupt will be Acknowledged if
the RC2IE and GIE bits are set.
8. Read the RCSTA2 register to determine if any
error occurred during reception, as well as read
bit 9 of data (if applicable).
9. Read RCREG2 to determine if the device is
being addressed.
10. If any error occurred, clear the CREN bit.
11. If the device has been addressed, clear the
ADDEN bit to allow all received data into the
receive buffer and interrupt the CPU.
To set up an Asynchronous Reception:
1.
Initialize the SPBRG2 register for the appropriate
baud rate. Set or clear the BRGH bit, as required,
to achieve the desired baud rate.
2. Enable the asynchronous serial port by clearing
bit, SYNC, and setting bit, SPEN.
3. If interrupts are desired, set enable bit, RC2IE.
4. If 9-bit reception is desired, set bit, RX9.
5. Enable the reception by setting bit, CREN.
6. Flag bit, RC2IF, will be set when reception is
complete and an interrupt will be generated if
enable bit, RC2IE, was set.
7. Read the RCSTA2 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
8. Read the 8-bit received data by reading the
RCREG2 register.
9. If any error occurred, clear the error by clearing
enable bit, CREN.
10. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
FIGURE 18-4:
SETTING UP 9-BIT MODE WITH
ADDRESS DETECT
AUSART RECEIVE BLOCK DIAGRAM
CREN
OERR
FERR
x64 Baud Rate CLK
SPBRG2
Baud Rate Generator
÷ 64
or
÷ 16
or
÷4
MSb
Stop
RSR Register
(8)
7
• • •
1
LSb
0
Start
RX9
Pin Buffer
and Control
Data
Recovery
RX2
RX9D
RCREG2 Register
FIFO
SPEN
8
Interrupt
RC2IF
Data Bus
RC2IE
DS39770B-page 256
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 18-5:
ASYNCHRONOUS RECEPTION
Start
bit
bit 0
RX2 (pin)
bit 1
Start
bit
bit 7/8 Stop
bit
bit 0
Rcv Shift Reg
Rcv Buffer Reg
Stop
bit
Start
bit
bit 7/8
Stop
bit
Word 2
RCREG2
Word 1
RCREG2
Read Rcv
Buffer Reg
RCREG2
bit 7/8
RC2IF
(Interrupt Flag)
OERR bit
CREN
Note:
This timing diagram shows three words appearing on the RX2 input. The RCREG2 (Receive Buffer register) is read after the third
word causing the OERR (Overrun) bit to be set.
TABLE 18-5:
Name
INTCON
REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION
Bit 7
Bit 6
Bit 5
GIE/GIEH PEIE/GIEL TMR0IE
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR3
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
54
PIE3
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
54
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
56
SYNC
—
BRGH
TRMT
TX9D
56
IPR3
RCSTA2
RCREG2
TXSTA2
SPBRG2
AUSART Receive Register
CSRC
TX9
TXEN
56
AUSART Baud Rate Generator Register
56
Legend: — = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous reception.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 257
PIC18F85J90 FAMILY
18.4
AUSART Synchronous
Master Mode
Once the TXREG2 register transfers the data to the
TSR register (occurs in one TCYCLE), the TXREG2 is
empty and the TX2IF flag bit (PIR3<4>) is set. The
interrupt can be enabled or disabled by setting or clearing the interrupt enable bit, TX2IE (PIE3<4>). TX2IF is
set regardless of the state of enable bit, TX2IE; it
cannot be cleared in software. It will reset only when
new data is loaded into the TXREG2 register.
The Synchronous Master mode is entered by setting
the CSRC bit (TXSTA2<7>). In this mode, the data is
transmitted in a half-duplex manner (i.e., transmission
and reception do not occur at the same time). When
transmitting data, the reception is inhibited and vice
versa. Synchronous mode is entered by setting bit,
SYNC (TXSTA2<4>). In addition, enable bit, SPEN
(RCSTA2<7>), is set in order to configure the TX2 and
RX2 pins to CK2 (clock) and DT2 (data) lines,
respectively.
While flag bit, TX2IF, indicates the status of the TXREG2
register, another bit, TRMT (TXSTA2<1>), shows the
status of the TSR register. TRMT is a read-only bit which
is set when the TSR is empty. No interrupt logic is tied to
this bit so the user has to poll this bit in order to determine if the TSR register is empty. The TSR is not
mapped in data memory so it is not available to the user.
The Master mode indicates that the processor transmits
the master clock on the CK2 line.
18.4.1
To set up a Synchronous Master Transmission:
AUSART SYNCHRONOUS MASTER
TRANSMISSION
1.
The AUSART transmitter block diagram is shown in
Figure 18-1. The heart of the transmitter is the Transmit
(Serial) Shift register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG2. The TXREG2 register is loaded with data in
software. The TSR register is not loaded until the last
bit has been transmitted from the previous load. As
soon as the last bit is transmitted, the TSR is loaded
with new data from the TXREG2 (if available).
2.
3.
4.
5.
6.
7.
8.
FIGURE 18-6:
Initialize the SPBRG2 register for the appropriate
baud rate.
Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
If interrupts are desired, set enable bit, TX2IE.
If 9-bit transmission is desired, set bit, TX9.
Enable the transmission by setting bit, TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the
TXREG2 register.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
SYNCHRONOUS TRANSMISSION
Q1 Q2 Q3Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4
Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RX2/DT2 pin
bit 0
bit 1
bit 2
bit 7
bit 0
bit 1
bit 7
Word 2
Word 1
TX2/CK2 pin
Write to
TXREG2 Reg
Write Word 1
Write Word 2
TX2IF bit
(Interrupt Flag)
TRMT bit
TXEN bit
Note:
‘1’
‘1’
Sync Master mode, SPBRG2 = 0; continuous transmission of two 8-bit words.
DS39770B-page 258
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 18-7:
SYNCHRONOUS TRANSMISSION (THROUGH TXEN)
RX2/DT2 pin
bit 0
bit 1
bit 2
bit 6
bit 7
TX2/CK2 pin
Write to
TXREG2 Reg
TX2IF bit
TRMT bit
TXEN bit
TABLE 18-6:
Name
INTCON
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION
Bit 7
Bit 6
Bit 5
GIE/GIEH PEIE/GIEL TMR0IE
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR3
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
54
PIE3
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
54
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
56
SYNC
—
BRGH
TRMT
TX9D
56
LATG3
LATG2
LATG1
LATG0
54
IPR3
RCSTA2
TXREG2
TXSTA2
SPBRG2
LATG
AUSART Transmit Register
CSRC
TX9
56
TXEN
AUSART Baud Rate Generator Register
U2OD
U1OD
—
LATG4
56
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master transmission.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 259
PIC18F85J90 FAMILY
18.4.2
AUSART SYNCHRONOUS
MASTER RECEPTION
4.
5.
6.
If interrupts are desired, set enable bit, RC2IE.
If 9-bit reception is desired, set bit, RX9.
If a single reception is required, set bit, SREN.
For continuous reception, set bit, CREN.
7. Interrupt flag bit, RC2IF, will be set when reception is complete and an interrupt will be generated
if the enable bit, RC2IE, was set.
8. Read the RCSTA2 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
9. Read the 8-bit received data by reading the
RCREG2 register.
10. If any error occurred, clear the error by clearing
bit, CREN.
11. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA2<5>), or the Continuous Receive
Enable bit, CREN (RCSTA2<4>). Data is sampled on
the RX2 pin on the falling edge of the clock.
If enable bit SREN is set, only a single word is received.
If enable bit CREN is set, the reception is continuous
until CREN is cleared. If both bits are set, then CREN
takes precedence.
To set up a Synchronous Master Reception:
1.
2.
3.
Initialize the SPBRG2 register for the appropriate
baud rate.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
Ensure bits CREN and SREN are clear.
FIGURE 18-8:
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RX2/DT2 pin
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
TX2/CK2 pin
Write to
bit SREN
SREN bit
CREN bit ‘0’
‘0’
RC2IF bit
(Interrupt)
Read
RCREG2
Note:
Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.
TABLE 18-7:
Name
INTCON
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Bit 7
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
Bit 6
GIE/GIEH PEIE/GIEL
PIR3
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
54
PIE3
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
54
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
56
SYNC
—
BRGH
TRMT
TX9D
IPR3
RCSTA2
RCREG2
TXSTA2
SPBRG2
AUSART Receive Register
CSRC
TX9
TXEN
56
AUSART Baud Rate Generator Register
56
56
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
DS39770B-page 260
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
18.5
AUSART Synchronous Slave Mode
Synchronous Slave mode is entered by clearing bit,
CSRC (TXSTA2<7>). This mode differs from the
Synchronous Master mode in that the shift clock is
supplied externally at the CK2 pin (instead of being
supplied internally in Master mode). This allows the
device to transfer or receive data while in any
low-power mode.
18.5.1
AUSART SYNCHRONOUS
SLAVE TRANSMIT
To set up a Synchronous Slave Transmission:
1.
Enable the synchronous slave serial port by
setting bits, SYNC and SPEN, and clearing bit,
CSRC.
Clear bits, CREN and SREN.
If interrupts are desired, set enable bit, TX2IE.
If 9-bit transmission is desired, set bit, TX9.
Enable the transmission by setting enable bit,
TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the
TXREG2 register.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
2.
3.
4.
5.
6.
The operation of the Synchronous Master and Slave
modes are identical except in the case of the Sleep
mode.
7.
8.
If two words are written to the TXREG2 and then the
SLEEP instruction is executed, the following will occur:
a)
b)
c)
d)
e)
The first word will immediately transfer to the
TSR register and transmit.
The second word will remain in TXREG2
register.
Flag bit, TX2IF, will not be set.
When the first word has been shifted out of TSR,
the TXREG2 register will transfer the second
word to the TSR and flag bit, TX2IF, will now be
set.
If enable bit, TX2IE, is set, the interrupt will wake
the chip from Sleep. If the global interrupt is
enabled, the program will branch to the interrupt
vector.
TABLE 18-8:
Name
REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR3
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
54
PIE3
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
54
IPR3
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
56
INTCON
RCSTA2
TXREG2
TXSTA2
SPBRG2
LATG
GIE/GIEH PEIE/GIEL
AUSART Transmit Register
CSRC
TX9
56
TXEN
SYNC
—
BRGH
TRMT
TX9D
AUSART Baud Rate Generator Register
U2OD
U1OD
—
LATG4
56
56
LATG3
LATG2
LATG1
LATG0
54
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave transmission.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 261
PIC18F85J90 FAMILY
18.5.2
AUSART SYNCHRONOUS
SLAVE RECEPTION
To set up a Synchronous Slave Reception:
1.
The operation of the Synchronous Master and Slave
modes is identical except in the case of Sleep or any
Idle mode, and bit SREN, which is a “don’t care” in
Slave mode.
If receive is enabled by setting the CREN bit prior to
entering Sleep, or any Idle mode, then a word may be
received while in this low-power mode. Once the word
is received, the RSR register will transfer the data to the
RCREG2 register; if the RC2IE enable bit is set, the
interrupt generated will wake the chip from low-power
mode. If the global interrupt is enabled, the program will
branch to the interrupt vector.
Enable the synchronous master serial port by
setting bits, SYNC and SPEN, and clearing bit,
CSRC.
If interrupts are desired, set enable bit, RC2IE.
If 9-bit reception is desired, set bit, RX9.
To enable reception, set enable bit, CREN.
Flag bit, RC2IF, will be set when reception is
complete. An interrupt will be generated if
enable bit, RC2IE, was set.
Read the RCSTA2 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG2 register.
If any error occurred, clear the error by clearing
bit, CREN.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
2.
3.
4.
5.
6.
7.
8.
9.
TABLE 18-9:
Name
INTCON
REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
Bit 7
Bit 6
Bit 5
GIE/GIEH PEIE/GIEL TMR0IE
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR3
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
54
PIE3
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
54
IPR3
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
54
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
RCSTA2
RCREG2
TXSTA2
SPBRG2
AUSART Receive Register
CSRC
TX9
TXEN
56
56
SYNC
—
BRGH
TRMT
TX9D
AUSART Baud Rate Generator Register
56
56
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.
DS39770B-page 262
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
19.0
10-BIT ANALOG-TO-DIGITAL
CONVERTER (A/D) MODULE
The Analog-to-Digital (A/D) converter module has
12 inputs for all PIC18F85J90 family devices. This
module allows conversion of an analog input signal to
a corresponding 10-bit digital number.
The ADCON0 register, shown in Register 19-1,
controls the operation of the A/D module. The
ADCON1 register, shown in Register 19-2, configures
the functions of the port pins. The ADCON2 register,
shown in Register 19-3, configures the A/D clock
source, programmed acquisition time and justification.
The module has five registers:
•
•
•
•
•
A/D Result High Register (ADRESH)
A/D Result Low Register (ADRESL)
A/D Control Register 0 (ADCON0)
A/D Control Register 1 (ADCON1)
A/D Control Register 2 (ADCON2)
REGISTER 19-1:
ADCON0: A/D CONTROL REGISTER 0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADCAL
—
CHS3
CHS2
CHS1
CHS0
GO/DONE
ADON
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
ADCAL: A/D Calibration bit
1 = Calibration is performed on next A/D conversion
0 = Normal A/D converter operation (no calibration is performed)
bit 6
Unimplemented: Read as ‘0’
bit 5-2
CHS3:CHS0: Analog Channel Select bits
0000 = Channel 00 (AN0)
0001 = Channel 01 (AN1)
0010 = Channel 02 (AN2)
0011 = Channel 03 (AN3)
0100 = Channel 04 (AN4)
0101 = Channel 05 (AN5)
0110 = Channel 06 (AN6)
0111 = Channel 07 (AN7)
1000 = Channel 08 (AN8)
1001 = Channel 09 (AN9)
1010 = Channel 10 (AN10)
1011 = Channel 11 (AN11)
11xx = Unused
bit 1
GO/DONE: A/D Conversion Status bit
When ADON = 1:
1 = A/D conversion in progress
0 = A/D Idle
bit 0
ADON: A/D On bit
1 = A/D converter module is enabled
0 = A/D converter module is disabled
© 2007 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39770B-page 263
PIC18F85J90 FAMILY
REGISTER 19-2:
ADCON1: A/D CONTROL REGISTER 1
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-6
Unimplemented: Read as ‘0’
bit 5
VCFG1: Voltage Reference Configuration bit (VREF- source)
1 = VREF- (AN2)
0 = AVSS
bit 4
VCFG0: Voltage Reference Configuration bit (VREF+ source)
1 = VREF+ (AN3)
0 = AVDD
bit 3-0
PCFG3:PCFG0: A/D Port Configuration Control bits:
PCFG3:
PCFG0
AN11 AN10 AN9
AN8
AN7
AN6
AN5
AN4
AN3
AN2
AN1
AN0
0000
A
A
A
A
A
A
A
A
A
A
A
A
0001
A
A
A
A
A
A
A
A
A
A
A
A
0010
A
A
A
A
A
A
A
A
A
A
A
A
0011
A
A
A
A
A
A
A
A
A
A
A
A
0100
D
A
A
A
A
A
A
A
A
A
A
A
0101
D
D
A
A
A
A
A
A
A
A
A
A
0110
D
D
D
A
A
A
A
A
A
A
A
A
0111
D
D
D
D
A
A
A
A
A
A
A
A
1000
D
D
D
D
D
A
A
A
A
A
A
A
1001
D
D
D
D
D
D
A
A
A
A
A
A
1010
D
D
D
D
D
D
D
A
A
A
A
A
1011
D
D
D
D
D
D
D
D
A
A
A
A
1100
D
D
D
D
D
D
D
D
D
A
A
A
1101
D
D
D
D
D
D
D
D
D
D
A
A
1110
D
D
D
D
D
D
D
D
D
D
D
A
1111
D
D
D
D
D
D
D
D
D
D
D
D
A = Analog input
DS39770B-page 264
x = Bit is unknown
D = Digital I/O
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 19-3:
ADCON2: A/D CONTROL REGISTER 2
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADFM
—
ACQT2
ACQT1
ACQT0
ADCS2
ADCS1
ADCS0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
ADFM: A/D Result Format Select bit
1 = Right justified
0 = Left justified
bit 6
Unimplemented: Read as ‘0’
bit 5-3
ACQT2:ACQT0: A/D Acquisition Time Select bits
111 = 20 TAD
110 = 16 TAD
101 = 12 TAD
100 = 8 TAD
011 = 6 TAD
010 = 4 TAD
001 = 2 TAD
000 = 0 TAD(1)
bit 2-0
ADCS2:ADCS0: A/D Conversion Clock Select bits
111 = FRC (clock derived from A/D RC oscillator)(1)
110 = FOSC/64
101 = FOSC/16
100 = FOSC/4
011 = FRC (clock derived from A/D RC oscillator)(1)
010 = FOSC/32
001 = FOSC/8
000 = FOSC/2
x = Bit is unknown
Note 1: If the A/D FRC clock source is selected, a delay of one TCY (instruction cycle) is added
before the A/D clock starts. This allows the SLEEP instruction to be executed before starting
a conversion.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 265
PIC18F85J90 FAMILY
The analog reference voltage is software selectable to
either the device’s positive and negative supply voltage
(AVDD and AVSS), or the voltage level on the
RA3/AN3/VREF+ and RA2/AN2/VREF- pins.
the A/D conversion. When the A/D conversion is complete, the result is loaded into the ADRESH:ADRESL
register pair, the GO/DONE bit (ADCON0<1>) is
cleared and A/D Interrupt Flag bit, ADIF, is set.
The A/D converter has a unique feature of being able
to operate while the device is in Sleep mode. To
operate in Sleep, the A/D conversion clock must be
derived from the A/D’s internal RC oscillator.
A device Reset forces all registers to their Reset state.
This forces the A/D module to be turned off and any
conversion in progress is aborted. The value in the
ADRESH:ADRESL register pair is not modified for a
Power-on Reset. These registers will contain unknown
data after a Power-on Reset.
The output of the sample and hold is the input into the
converter, which generates the result via successive
approximation.
The block diagram of the A/D module is shown in
Figure 19-1.
Each port pin associated with the A/D converter can be
configured as an analog input or as a digital I/O. The
ADRESH and ADRESL registers contain the result of
FIGURE 19-1:
A/D BLOCK DIAGRAM(1,2)
CHS3:CHS0
1011
1010
1001
1000
0111
0110
0101
0100
VAIN
0011
(Input Voltage)
10-Bit
Converter
A/D
0010
0001
VCFG1:VCFG0
0000
VDD
Reference
Voltage
AN11
AN10
AN9
AN8
AN7
AN6
AN5
AN4
AN3
AN2
AN1
AN0
VREF+
VREFVSS
Note 1: Channels AN15 through AN12 are not available on 64-pin devices.
2: I/O pins have diode protection to VDD and VSS.
DS39770B-page 266
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
After the A/D module has been configured as desired,
the selected channel must be acquired before the
conversion is started. The analog input channels must
have their corresponding TRIS bits selected as an
input. To determine acquisition time, see Section 19.1
“A/D Acquisition Requirements”. After this acquisition time has elapsed, the A/D conversion can be
started. An acquisition time can be programmed to
occur between setting the GO/DONE bit and the actual
start of the conversion.
The following steps should be followed to do an A/D
conversion:
1.
2.
3.
4.
Wait the required acquisition time (if required).
Start conversion:
• Set GO/DONE bit (ADCON0<1>)
Wait for A/D conversion to complete, by either:
• Polling for the GO/DONE bit to be cleared
5.
OR
• Waiting for the A/D interrupt
Read A/D Result registers (ADRESH:ADRESL);
clear ADIF bit, if required.
For next conversion, go to step 1 or step 2, as
required. The A/D conversion time per bit is
defined as TAD. A minimum wait of 2 TAD is
required before next acquisition starts.
6.
7.
Configure the A/D module:
• Configure analog pins, voltage reference and
digital I/O (ADCON1)
• Select A/D input channel (ADCON0)
• Select A/D acquisition time (ADCON2)
• Select A/D conversion clock (ADCON2)
• Turn on A/D module (ADCON0)
Configure A/D interrupt (if desired):
• Clear ADIF bit
• Set ADIE bit
• Set GIE bit
FIGURE 19-2:
ANALOG INPUT MODEL
VDD
Sampling
Switch
VT = 0.6V
RS
VAIN
RIC ≤ 1k
ANx
CPIN
5 pF
VT = 0.6V
SS
RSS
ILEAKAGE
±100 nA
CHOLD = 25 pF
VSS
Legend: CPIN
= Input Capacitance
VT
= Threshold Voltage
ILEAKAGE = Leakage Current at the pin due to
various junctions
= Interconnect Resistance
RIC
= Sampling Switch
SS
= Sample/Hold Capacitance (from DAC)
CHOLD
RSS
= Sampling Switch Resistance
© 2007 Microchip Technology Inc.
Preliminary
VDD
6V
5V
4V
3V
2V
1
2
3
4
Sampling Switch (kΩ)
DS39770B-page 267
PIC18F85J90 FAMILY
19.1
A/D Acquisition Requirements
For the A/D converter to meet its specified accuracy,
the charge holding capacitor (CHOLD) must be allowed
to fully charge to the input channel voltage level. The
analog input model is shown in Figure 19-2. The
source impedance (RS) and the internal sampling
switch (RSS) impedance directly affect the time
required to charge the capacitor CHOLD. The sampling
switch (RSS) impedance varies over the device voltage
(VDD). The source impedance affects the offset voltage
at the analog input (due to pin leakage current). The
maximum recommended impedance for analog
sources is 2.5 kΩ. After the analog input channel is
selected (changed), the channel must be sampled for
at least the minimum acquisition time before starting a
conversion.
Note:
CHOLD
Rs
Conversion Error
VDD
Temperature
=
=
≤
=
=
25 pF
2.5 kΩ
1/2 LSb
3V → Rss = 2 kΩ
85°C (system max.)
ACQUISITION TIME
=
Amplifier Settling Time + Holding Capacitor Charging Time + Temperature Coefficient
=
TAMP + TC + TCOFF
EQUATION 19-2:
VHOLD
or
TC
Equation 19-3 shows the calculation of the minimum
required acquisition time, TACQ. This calculation is
based on the following application system
assumptions:
When the conversion is started, the
holding capacitor is disconnected from the
input pin.
EQUATION 19-1:
TACQ
To calculate the minimum acquisition time,
Equation 19-1 may be used. This equation assumes
that 1/2 LSb error is used (1024 steps for the A/D). The
1/2 LSb error is the maximum error allowed for the A/D
to meet its specified resolution.
A/D MINIMUM CHARGING TIME
=
(VREF – (VREF/2048)) • (1 – e(-TC/CHOLD(RIC + RSS + RS)))
=
-(CHOLD)(RIC + RSS + RS) ln(1/2048)
EQUATION 19-3:
CALCULATING THE MINIMUM REQUIRED ACQUISITION TIME
TACQ
=
TAMP + TC + TCOFF
TAMP
=
0.2 μs
TCOFF
=
(Temp – 25°C)(0.02 μs/°C)
(85°C – 25°C)(0.02 μs/°C)
1.2 μs
Temperature coefficient is only required for temperatures > 25°C. Below 25°C, TCOFF = 0 ms.
TC
=
-(CHOLD)(RIC + RSS + RS) ln(1/2048) μs
-(25 pF) (1 kΩ + 2 kΩ + 2.5 kΩ) ln(0.0004883) μs
1.05 μs
TACQ
=
0.2 μs + 1 μs + 1.2 μs
2.4 μs
DS39770B-page 268
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
19.2
TABLE 19-1:
Selecting and Configuring
Automatic Acquisition Time
AD Clock Source (TAD)
The ADCON2 register allows the user to select an
acquisition time that occurs each time the GO/DONE
bit is set.
When the GO/DONE bit is set, sampling is stopped and
a conversion begins. The user is responsible for ensuring the required acquisition time has passed between
selecting the desired input channel and setting the
GO/DONE bit. This occurs when the ACQT2:ACQT0
bits (ADCON2<5:3>) remain in their Reset state (‘000’)
and is compatible with devices that do not offer
programmable acquisition times.
If desired, the ACQT bits can be set to select a programmable acquisition time for the A/D module. When
the GO/DONE bit is set, the A/D module continues to
sample the input for the selected acquisition time, then
automatically begins a conversion. Since the acquisition time is programmed, there may be no need to wait
for an acquisition time between selecting a channel and
setting the GO/DONE bit.
In either case, when the conversion is completed, the
GO/DONE bit is cleared, the ADIF flag is set and the
A/D begins sampling the currently selected channel
again. If an acquisition time is programmed, there is
nothing to indicate if the acquisition time has ended or
if the conversion has begun.
19.3
Selecting the A/D Conversion
Clock
Operation
ADCS2:ADCS0
Maximum
Device
Frequency
2 TOSC
000
2.86 MHz
TOSC
100
5.71 MHz
8 TOSC
001
11.43 MHz
16 TOSC
101
22.86 MHz
32 TOSC
010
40.0 MHz
64 TOSC
110
40.0 MHz
RC(2)
x11
1.00 MHz(1)
4
Note 1: The RC source has a typical TAD time of
4 μs.
2: For device frequencies above 1 MHz, the
device must be in Sleep mode for the entire
conversion or the A/D accuracy may be out
of specification.
19.4
Configuring Analog Port Pins
The ADCON1, TRISA, TRISF and TRISH registers
control the operation of the A/D port pins. The port pins
needed as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared
(output), the digital output level (VOH or VOL) will be
converted.
The A/D operation is independent of the state of the
CHS3:CHS0 bits and the TRIS bits.
The A/D conversion time per bit is defined as TAD. The
A/D conversion requires 11 TAD per 10-bit conversion.
The source of the A/D conversion clock is software
selectable.
There are seven possible options for TAD:
•
•
•
•
•
•
•
TAD vs. DEVICE OPERATING
FREQUENCIES
2 TOSC
4 TOSC
8 TOSC
16 TOSC
32 TOSC
64 TOSC
Internal RC Oscillator
Note 1: When reading the PORT register, all pins
configured as analog input channels will
read as cleared (a low level). Pins configured as digital inputs will convert an
analog input. Analog levels on a digitally
configured input will be accurately
converted.
2: Analog levels on any pin defined as a
digital input may cause the digital input
buffer to consume current out of the
device’s specification limits.
For correct A/D conversions, the A/D conversion clock
(TAD) must be as short as possible but greater than the
minimum TAD (see parameter 130 in Table 25-25 for
more information).
Table 19-1 shows the resultant TAD times derived from
the device operating frequencies and the A/D clock
source selected.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 269
PIC18F85J90 FAMILY
19.5
A/D Conversions
19.6
Figure 19-3 shows the operation of the A/D converter
after the GO/DONE bit has been set and the
ACQT2:ACQT0 bits are cleared. A conversion is
started after the following instruction to allow entry into
Sleep mode before the conversion begins.
An A/D conversion can be started by the “Special Event
Trigger” of the CCP2 module. This requires that the
CCP2M3:CCP2M0
bits
(CCP2CON<3:0>)
be
programmed as ‘1011’ and that the A/D module is
enabled (ADON bit is set). When the trigger occurs, the
GO/DONE bit will be set, starting the A/D acquisition
and conversion and the Timer1 (or Timer3) counter will
be reset to zero. Timer1 (or Timer3) is reset to automatically repeat the A/D acquisition period with minimal
software overhead (moving ADRESH/ADRESL to the
desired location). The appropriate analog input
channel must be selected and the minimum acquisition
period is either timed by the user, or an appropriate
TACQ time is selected before the Special Event Trigger
sets the GO/DONE bit (starts a conversion).
Figure 19-4 shows the operation of the A/D converter
after the GO/DONE bit has been set, the
ACQT2:ACQT0 bits are set to ‘010’ and selecting a
4 TAD acquisition time before the conversion starts.
Clearing the GO/DONE bit during a conversion will
abort the current conversion. The A/D Result register
pair will NOT be updated with the partially completed
A/D
conversion
sample.
This
means
the
ADRESH:ADRESL registers will continue to contain
the value of the last completed conversion (or the last
value written to the ADRESH:ADRESL registers).
If the A/D module is not enabled (ADON is cleared), the
Special Event Trigger will be ignored by the A/D
module but will still reset the Timer1 (or Timer3)
counter.
After the A/D conversion is completed or aborted, a
2 TAD wait is required before the next acquisition can be
started. After this wait, acquisition on the selected
channel is automatically started.
Note:
Use of the CCP2 Trigger
The GO/DONE bit should NOT be set in
the same instruction that turns on the A/D.
FIGURE 19-3:
A/D CONVERSION TAD CYCLES (ACQT2:ACQT0 = 000, TACQ = 0)
TCY - TAD TAD1 TAD2 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 TAD9 TAD10 TAD11
b4
b1
b0
b6
b7
b2
b9
b8
b3
b5
Conversion starts
Holding capacitor is disconnected from analog input (typically 100 ns)
Set GO/DONE bit
Next Q4: ADRESH/ADRESL is loaded, GO/DONE bit is cleared,
ADIF bit is set, holding capacitor is connected to analog input.
A/D CONVERSION TAD CYCLES (ACQT2:ACQT0 = 010, TACQ = 4 TAD)
FIGURE 19-4:
TAD Cycles
TACQT Cycles
1
2
3
4
1
2
b9
Automatic
Acquisition
Time
4
5
b8
b7
b6
6
b5
7
b4
8
9
10
11
b3
b2
b1
b0
Conversion starts
(Holding capacitor is disconnected)
Set GO/DONE bit
(Holding capacitor continues
acquiring input)
DS39770B-page 270
3
Next Q4: ADRESH:ADRESL is loaded, GO/DONE bit is cleared,
ADIF bit is set, holding capacitor is reconnected to analog input.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
19.7
A/D Converter Calibration
The A/D converter in the PIC18F85J90 family of
devices includes a self-calibration feature which compensates for any offset generated within the module.
The calibration process is automated and is initiated by
setting the ADCAL bit (ADCON0<7>). The next time
the GO/DONE bit is set, the module will perform a
“dummy” conversion (that is, with reading none of the
input channels) and store the resulting value internally
to compensate for offset. Thus, subsequent offsets will
be compensated.
The calibration process assumes that the device is in a
relatively steady-state operating condition. If A/D
calibration is used, it should be performed after each
device Reset or if there are other major changes in
operating conditions.
19.8
Operation in Power-Managed
Modes
The selection of the automatic acquisition time and A/D
conversion clock is determined in part by the clock
source and frequency while in a power-managed
mode.
TABLE 19-2:
Name
If the A/D is expected to operate while the device is in
a power-managed mode, the ACQT2:ACQT0 and
ADCS2:ADCS0 bits in ADCON2 should be updated in
accordance with the power-managed mode clock that
will be used. After the power-managed mode is entered
(either of the power-managed Run modes), an A/D
acquisition or conversion may be started. Once an
acquisition or conversion is started, the device should
continue to be clocked by the same power-managed
mode clock source until the conversion has been completed. If desired, the device may be placed into the
corresponding power-managed Idle mode during the
conversion.
If the power-managed mode clock frequency is less
than 1 MHz, the A/D RC clock source should be
selected.
Operation in the Sleep mode requires the A/D RC clock
to be selected. If bits ACQT2:ACQT0 are set to ‘000’
and a conversion is started, the conversion will be
delayed one instruction cycle to allow execution of the
SLEEP instruction and entry to Sleep mode. The IDLEN
and SCS bits in the OSCCON register must have
already been cleared prior to starting the conversion.
SUMMARY OF A/D REGISTERS
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR1
—
ADIF
RC1IF
TX1IF
SSPIF
—
TMR2IF
TMR1IF
54
PIE1
—
ADIE
RC1IE
TX1IE
SSPIE
—
TMR2IE
TMR1IE
54
IPR1
—
ADIP
RC1IP
TX1IP
SSPIP
—
TMR2IP
TMR1IP
54
PIR3
—
LCDIF
RC2IF
TX2IF
—
CCP2IF
CCP1IF
—
54
PIE3
—
LCDIE
RC2IE
TX2IE
—
CCP2IE
CCP1IE
—
54
—
LCDIP
RC2IP
TX2IP
—
CCP2IP
CCP1IP
—
54
INTCON
IPR3
GIE/GIEH PEIE/GIEL
ADRESH
A/D Result Register High Byte
ADRESL
A/D Result Register Low Byte
ADCAL
—
ADCON1
—
ADCON2
ADFM
ADCON0
CCP2CON
PORTA
TRISA
53
53
CHS3
CHS3
CHS1
CHS0
GO/DONE
ADON
53
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
53
—
ACQT2
ACQT1
ACQT0
ADCS2
ADCS1
ADCS0
53
—
—
DC2B1
DC2B0
CCP2M3
CCP2M2
CCP2M1
CCP2M0
55
RA7(1)
RA6(1)
RA5
RA4
RA3
RA2
RA1
RA0
55
TRISA7(1) TRISA6(1)
TRISA5
TRISA4
TRISA3
TRISA2
TRISA1
TRISA0
54
PORTF
RF7
RF6
RF5
RF4
RF3
RF2
RF1
—
54
TRISF
TRISF5
TRISF4
TRISF5
TRISF4
TRISF3
TRISF2
TRISF1
—
54
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for A/D conversion.
Note 1: RA6/RA7 and their associated latch and direction bits are configured as port pins only when the internal
oscillator is selected as the default clock source (FOSC2 Configuration bit = 0); otherwise, they are
disabled and these bits read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 271
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 272
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
20.0
COMPARATOR MODULE
The analog comparator module contains two
comparators that can be configured in a variety of
ways. The inputs can be selected from the analog
inputs multiplexed with pins RF1 through RF6, as well
as the on-chip voltage reference (see Section 21.0
“Comparator Voltage Reference Module”). The digital outputs (normal or inverted) are available at the pin
level and can also be read through the control register.
REGISTER 20-1:
The CMCON register (Register 20-1) selects the
comparator input and output configuration. Block
diagrams of the various comparator configurations are
shown in Figure 20-1.
CMCON: COMPARATOR MODULE CONTROL REGISTER
R-0
R-0
R/W-0
R/W-0
R/W-0
R/W-1
R/W-1
R/W-1
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
C2OUT: Comparator 2 Output bit
When C2INV = 0:
1 = C2 VIN+ > C2 VIN0 = C2 VIN+ < C2 VINWhen C2INV = 1:
1 = C2 VIN+ < C2 VIN0 = C2 VIN+ > C2 VIN-
bit 6
C1OUT: Comparator 1 Output bit
When C1INV = 0:
1 = C1 VIN+ > C1 VIN0 = C1 VIN+ < C1 VINWhen C1INV = 1:
1 = C1 VIN+ < C1 VIN0 = C1 VIN+ > C1 VIN-
bit 5
C2INV: Comparator 2 Output Inversion bit
1 = C2 output inverted
0 = C2 output not inverted
bit 4
C1INV: Comparator 1 Output Inversion bit
1 = C1 output inverted
0 = C1 output not inverted
bit 3
CIS: Comparator Input Switch bit
When CM2:CM0 = 110:
1 = C1 VIN- connects to RF5/AN10/CVREF
C2 VIN- connects to RF3/AN8
0 = C1 VIN- connects to RF6/AN11
C2 VIN- connects to RF4/AN9
bit 2-0
CM2:CM0: Comparator Mode bits
Figure 20-1 shows the Comparator modes and the CM2:CM0 bit settings.
© 2007 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39770B-page 273
PIC18F85J90 FAMILY
20.1
Comparator Configuration
There are eight modes of operation for the comparators, shown in Figure 20-1. Bits CM2:CM0 of the
CMCON register are used to select these modes. The
TRISF register controls the data direction of the
comparator pins for each mode. If the Comparator
FIGURE 20-1:
RF4/AN9/
SEG22
RF3/AN8/
SEG21
A
A
Comparator interrupts should be disabled
during a Comparator mode change;
otherwise, a false interrupt may occur.
Comparators Off (POR Default Value)
CM2:CM0 = 111
C1
Off (Read as ‘0’)
RF6/AN11/ D
SEG24
RF5/AN10/ D
CVREF/SEG23
C2
Off (Read as ‘0’)
RF4/AN9/
SEG22
RF3/AN8/
SEG21
VINVIN+
VINVIN+
Two Independent Comparators
CM2:CM0 = 010
RF6/AN11/ A
SEG24
RF5/AN10/ A
CVREF/SEG23
VIN+
A
VIN-
A
VIN+
RF4/AN9/
SEG22
RF3/AN8/
SEG21
Note:
COMPARATOR I/O OPERATING MODES
Comparator Outputs Disabled
CM2:CM0 = 000
RF6/AN11/ A
SEG24
RF5/AN10/ A
CVREF/SEG23
mode is changed, the comparator output level may not
be valid for the specified mode change delay shown in
Section 25.0 “Electrical Characteristics”.
VINVIN+
D
VIN-
D
VIN+
C1
Off (Read as ‘0’)
C2
Off (Read as ‘0’)
Two Independent Comparators with Outputs
CM2:CM0 = 011
VINRF6/AN11/ A
SEG24
C1
V
IN+
RF5/AN10/ A
CVREF/SEG23
RF2/AN7/C1OUT*/SEG20
VIN-
C1
C1OUT
C2
C2OUT
RF4/AN9/
SEG22
RF3/AN8/
SEG21
A
VIN-
A
VIN+
C1OUT
C2OUT
C2
RF1/AN6/C2OUT*/SEG19
Two Common Reference Comparators
CM2:CM0 = 100
RF6/AN11/ A
SEG24
RF5/AN10/ A
CVREF/SEG23
VIN+
RF4/AN9/
SEG22
A
VIN-
RF3/AN8/
SEG21
D
VIN+
Two Common Reference Comparators with Outputs
CM2:CM0 = 101
A
RF6/AN11/
SEG24
A
RF5/AN10/
CVREF/SEG23
VIN-
C1
C1OUT
VINVIN+
C1
C1OUT
C2
C2OUT
RF2/AN7/C1OUT*/
SEG20
C2
RF4/AN9/
SEG22
RF3/AN8/
SEG21
C2OUT
A
VIN-
D
VIN+
RF1/AN6/C2OUT*/SEG19
Four Inputs Multiplexed to Two Comparators
CM2:CM0 = 110
One Independent Comparator with Output
CM2:CM0 = 001
RF6/AN11/ A
SEG24
RF5/AN10/ A
CVREF/SEG23
RF6/AN11/ A
SEG24
RF5/AN10/ A
CVREF/SEG23
VINVIN+
C1
C1OUT
RF2/AN7/C1OUT*/SEG20
RF4/AN9/
SEG22
RF3/AN8/
SEG21
D
VIN-
D
VIN+
RF4/AN9/
SEG22
RF3/AN8/
SEG21
C2
CIS = 0
CIS = 1
VINVIN+
C1
C1OUT
C2
C2OUT
A
A
CIS = 0
CIS = 1
VINVIN+
Off (Read as ‘0’)
CVREF
From VREF module
A = Analog Input, port reads zeros always
D = Digital Input
CIS (CMCON<3>) is the Comparator Input Switch
* Setting the TRISF<2:1> bits will disable the comparator outputs by configuring the pins as inputs.
DS39770B-page 274
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
20.2
20.3.2
Comparator Operation
A single comparator is shown in Figure 20-2, along with
the relationship between the analog input levels and
the digital output. When the analog input at VIN+ is less
than the analog input VIN-, the output of the comparator
is a digital low level. When the analog input at VIN+ is
greater than the analog input VIN-, the output of the
comparator is a digital high level. The shaded areas of
the output of the comparator in Figure 20-2 represent
the uncertainty due to input offsets and response time.
20.3
Comparator Reference
Depending on the comparator operating mode, either
an external or internal voltage reference may be used.
The analog signal present at VIN- is compared to the
signal at VIN+ and the digital output of the comparator
is adjusted accordingly (Figure 20-2).
FIGURE 20-2:
SINGLE COMPARATOR
VIN+
+
VIN-
–
The internal reference is only available in the mode
where four inputs are multiplexed to two comparators
(CM2:CM0 = 110). In this mode, the internal voltage
reference is applied to the VIN+ pin of both
comparators.
20.4
Comparator Response Time
Response time is the minimum time, after selecting a
new reference voltage or input source, before the
comparator output has a valid level. If the internal reference is changed, the maximum delay of the internal
voltage reference must be considered when using the
comparator outputs. Otherwise, the maximum delay of
the comparators should be used (see Section 25.0
“Electrical Characteristics”).
Comparator Outputs
The comparator outputs are read through the CMCON
register. These bits are read-only. The comparator
outputs may also be directly output to the RF1 and RF2
I/O pins. When enabled, multiplexors in the output path
of the RF1 and RF2 pins will switch and the output of
each pin will be the unsynchronized output of the
comparator. The uncertainty of each of the
comparators is related to the input offset voltage and
the response time given in the specifications.
Figure 20-3 shows the comparator output block
diagram.
VINVIN+
Output
20.3.1
The comparator module also allows the selection of an
internally generated voltage reference from the
comparator voltage reference module. This module is
described in more detail in Section 21.0 “Comparator
Voltage Reference Module”.
20.5
Output
INTERNAL REFERENCE SIGNAL
The TRISF bits will still function as an output enable/
disable for the RF1 and RF2 pins while in this mode.
EXTERNAL REFERENCE SIGNAL
When external voltage references are used, the
comparator module can be configured to have the comparators operate from the same or different reference
sources. However, threshold detector applications may
require the same reference. The reference signal must
be between VSS and VDD and can be applied to either
pin of the comparator(s).
© 2007 Microchip Technology Inc.
The polarity of the comparator outputs can be changed
using the C2INV and C1INV bits (CMCON<5:4>).
Note 1: When reading the PORT register, all pins
configured as analog inputs will read as
‘0’. Pins configured as digital inputs will
convert an analog input according to the
Schmitt Trigger input specification.
Preliminary
2: Analog levels on any pin defined as a
digital input may cause the input buffer to
consume more current than is specified.
DS39770B-page 275
PIC18F85J90 FAMILY
+
To RF1 or
RF2 pin
-
Port pins
COMPARATOR OUTPUT BLOCK DIAGRAM
MULTIPLEX
FIGURE 20-3:
D
Q
Bus
Data
CxINV
EN
Read CMCON
D
Q
EN
CL
From
Other
Comparator
Reset
20.6
Comparator Interrupts
20.7
The comparator interrupt flag is set whenever there is
a change in the output value of either comparator.
Software will need to maintain information about the
status of the output bits, as read from CMCON<7:6>, to
determine the actual change that occurred. The CMIF
bit (PIR2<6>) is the Comparator Interrupt Flag. The
CMIF bit must be reset by clearing it. Since it is also
possible to write a ‘1’ to this register, a simulated
interrupt may be initiated.
Both the CMIE bit (PIE2<6>) and the PEIE bit
(INTCON<6>) must be set to enable the interrupt. In
addition, the GIE bit (INTCON<7>) must also be set. If
any of these bits are clear, the interrupt is not enabled,
though the CMIF bit will still be set if an interrupt
condition occurs.
Note:
If a change in the CMCON register
(C1OUT or C2OUT) should occur when a
read operation is being executed (start of
the Q2 cycle), then the CMIF (PIR2<6>)
interrupt flag may not get set.
The user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a)
b)
Set
CMIF
bit
Comparator Operation
During Sleep
When a comparator is active and the device is placed
in Sleep mode, the comparator remains active and the
interrupt is functional, if enabled. This interrupt will
wake-up the device from Sleep mode, when enabled.
Each operational comparator will consume additional
current, as shown in the comparator specifications. To
minimize power consumption while in Sleep mode, turn
off the comparators (CM2:CM0 = 111) before entering
Sleep. If the device wakes up from Sleep, the contents
of the CMCON register are not affected.
20.8
Effects of a Reset
A device Reset forces the CMCON register to its Reset
state, causing the comparator modules to be turned off
(CM2:CM0 = 111). However, the input pins (RF3
through RF6) are configured as analog inputs by
default on device Reset. The I/O configuration for these
pins is determined by the setting of the PCFG3:PCFG0
bits (ADCON1<3:0>). Therefore, device current is
minimized when analog inputs are present at Reset
time.
Any read or write of CMCON will end the
mismatch condition.
Clear flag bit CMIF.
A mismatch condition will continue to set flag bit CMIF.
Reading CMCON will end the mismatch condition and
allow flag bit CMIF to be cleared.
DS39770B-page 276
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
20.9
Analog Input Connection
Considerations
range by more than 0.6V in either direction, one of the
diodes is forward biased and a latch-up condition may
occur. A maximum source impedance of 10 kΩ is
recommended for the analog sources. Any external
component connected to an analog input pin, such as
a capacitor or a Zener diode, should have very little
leakage current.
A simplified circuit for an analog input is shown in
Figure 20-4. Since the analog pins are connected to a
digital output, they have reverse biased diodes to VDD
and VSS. The analog input, therefore, must be between
VSS and VDD. If the input voltage deviates from this
FIGURE 20-4:
COMPARATOR ANALOG INPUT MODEL
VDD
VT = 0.6V
RS < 10k
RIC
Comparator
Input
AIN
CPIN
5 pF
VA
VT = 0.6V
ILEAKAGE
±500 nA
VSS
Legend:
TABLE 20-1:
Name
INTCON
CPIN
VT
ILEAKAGE
RIC
RS
VA
=
=
=
=
=
=
Input Capacitance
Threshold Voltage
Leakage Current at the pin due to various junctions
Interconnect Resistance
Source Impedance
Analog Voltage
REGISTERS ASSOCIATED WITH COMPARATOR MODULE
Bit 7
Bit 6
GIE/GIEH PEIE/GIEL
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
51
PIR2
OSCFIF
CMIF
—
—
BCLIF
LVDIF
TMR3IF
—
54
PIE2
OSCFIE
CMIE
—
—
BCLIE
LVDIE
TMR3IE
—
54
IPR2
OSCFIP
CMIP
—
—
BCLIP
LVDIP
TMR3IP
—
54
CMCON
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
53
CVRCON
CVREN
CVROE
CVRR
CVRSS
CVR3
CVR2
CVR1
CVR0
53
RF7
RF6
RF5
RF4
RF3
RF2
RF1
—
54
PORTF
LATF
LATF7
LATF6
LATF5
LATF4
LATF3
LATF2
LATF1
—
54
TRISF
TRISF7
TRISF6
TRISF5
TRISF4
TRISF3
TRISF2
TRISF1
—
54
Legend: — = unimplemented, read as ‘0’. Shaded cells are unused by the comparator module.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 277
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 278
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
21.0
COMPARATOR VOLTAGE
REFERENCE MODULE
The comparator voltage reference is a 16-tap resistor
ladder network that provides a selectable reference
voltage. Although its primary purpose is to provide a
reference for the analog comparators, it may also be
used independently of them.
A block diagram of the module is shown in Figure 21-1.
The resistor ladder is segmented to provide two ranges
of CVREF values and has a power-down function to
conserve power when the reference is not being used.
The module’s supply reference can be provided from
either device VDD/VSS or an external voltage reference.
The range to be used is selected by the CVRR bit
(CVRCON<5>). The primary difference between the
ranges is the size of the steps selected by the CVREF
Selection bits (CVR3:CVR0), with one range offering
finer resolution. The equations used to calculate the
output of the comparator voltage reference are as
follows:
If CVRR = 1:
CVREF = ((CVR3:CVR0)/24) x (CVRSRC)
If CVRR = 0:
CVREF = (CVRSRC/4) + ((CVR3:CVR0)/32) x
(CVRSRC)
Configuring the Comparator
Voltage Reference
The comparator reference supply voltage can come
from either VDD and VSS, or the external VREF+ and
VREF- that are multiplexed with RA2 and RA3. The
voltage source is selected by the CVRSS bit
(CVRCON<4>).
The comparator voltage reference module is controlled
through the CVRCON register (Register 21-1). The
comparator voltage reference provides two ranges of
output voltage, each with 16 distinct levels.
The settling time of the comparator voltage reference
must be considered when changing the CVREF
output (see Table 25-3 in Section 25.0 “Electrical
Characteristics”).
21.1
REGISTER 21-1:
CVRCON: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CVREN
CVROE(1)
CVRR
CVRSS
CVR3
CVR2
CVR1
CVR0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
CVREN: Comparator Voltage Reference Enable bit
1 = CVREF circuit powered on
0 = CVREF circuit powered down
bit 6
CVROE: Comparator VREF Output Enable bit(1)
1 = CVREF voltage level is also output on the RF5/AN10/CVREF/SEG23 pin
0 = CVREF voltage is disconnected from the RF5/AN10/CVREF/SEG23 pin
bit 5
CVRR: Comparator VREF Range Selection bit
1 = 0 to 0.667 CVRSRC, with CVRSRC/24 step size (low range)
0 = 0.25 CVRSRC to 0.75 CVRSRC, with CVRSRC/32 step size (high range)
bit 4
CVRSS: Comparator VREF Source Selection bit
1 = Comparator reference source, CVRSRC = (VREF+) – (VREF-)
0 = Comparator reference source, CVRSRC = VDD – VSS
bit 3-0
CVR3:CVR0: Comparator VREF Value Selection bits (0 ≤ (CVR3:CVR0) ≤ 15)
When CVRR = 1:
CVREF = ((CVR3:CVR0)/24) • (CVRSRC)
When CVRR = 0:
CVREF = (CVRSRC/4) + ((CVR3:CVR0)/32) • (CVRSRC)
Note 1:
CVROE overrides the TRISF<5> bit setting.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 279
PIC18F85J90 FAMILY
FIGURE 21-1:
COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM
VREF+
VDD
CVRSS = 1
8R
CVRSS = 0
CVR3:CVR0
R
CVREN
R
16-to-1 MUX
R
R
16 Steps
CVREF
R
R
R
CVRR
VREF-
8R
CVRSS = 1
CVRSS = 0
21.2
Voltage Reference Accuracy/Error
The full range of voltage reference cannot be realized
due to the construction of the module. The transistors
on the top and bottom of the resistor ladder network
(Figure 21-1) keep CVREF from approaching the reference source rails. The voltage reference is derived
from the reference source; therefore, the CVREF output
changes with fluctuations in that source. The tested
absolute accuracy of the voltage reference can be
found in Section 25.0 “Electrical Characteristics”.
21.3
Operation During Sleep
When the device wakes up from Sleep through an
interrupt or a Watchdog Timer time-out, the contents of
the CVRCON register are not affected. To minimize
current consumption in Sleep mode, the voltage
reference should be disabled.
21.4
Effects of a Reset
A device Reset disables the voltage reference by
clearing bit, CVREN (CVRCON<7>). This Reset also
disconnects the reference from the RA2 pin by clearing
bit, CVROE (CVRCON<6>) and selects the high-voltage
range by clearing bit, CVRR (CVRCON<5>). The CVR
value select bits are also cleared.
21.5
Connection Considerations
The voltage reference module operates independently
of the comparator module. The output of the reference
generator may be connected to the RF5 pin if the
CVROE bit is set. Enabling the voltage reference output onto RA2 when it is configured as a digital input will
increase current consumption. Connecting RF5 as a
digital output with CVRSS enabled will also increase
current consumption.
The RF5 pin can be used as a simple D/A output with
limited drive capability. Due to the limited current drive
capability, a buffer must be used on the voltage
reference output for external connections to VREF.
Figure 21-2 shows an example buffering technique.
DS39770B-page 280
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 21-2:
COMPARATOR VOLTAGE REFERENCE OUTPUT BUFFER EXAMPLE
PIC18F85J90
CVREF
Module
R(1)
Voltage
Reference
Output
Impedance
Note 1:
TABLE 21-1:
Name
+
–
RF5
CVREF Output
R is dependent upon the Comparator Voltage Reference bits, CVRCON<5> and CVRCON<3:0>.
REGISTERS ASSOCIATED WITH COMPARATOR VOLTAGE REFERENCE
Bit 7
Bit 6
CVRCON
CVREN
CMCON
C2OUT
TRISF
TRISF7
Reset
Values
on page
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CVROE
CVRR
CVRSS
CVR3
CVR2
CVR1
CVR0
53
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
53
TRISF6
TRISF5
TRISF4
TRISF3
TRISF2
TRISF1
—
54
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used with the comparator voltage reference.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 281
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 282
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
22.0
SPECIAL FEATURES OF THE
CPU
PIC18F85J90 family devices include several features
intended to maximize reliability and minimize cost
through elimination of external components. These are:
• Oscillator Selection
• Resets:
- Power-on Reset (POR)
- Power-up Timer (PWRT)
- Oscillator Start-up Timer (OST)
- Brown-out Reset (BOR)
• Interrupts
• Watchdog Timer (WDT)
• Fail-Safe Clock Monitor
• Two-Speed Start-up
• Code Protection
• In-Circuit Serial Programming
A complete discussion of device Resets and interrupts
is available in previous sections of this data sheet.
In addition to their Power-up and Oscillator Start-up
Timers provided for Resets, the PIC18F85J90 family
family of devices have a configurable Watchdog Timer
which is controlled in software.
The inclusion of an internal RC oscillator also provides
the additional benefits of a Fail-Safe Clock Monitor
(FSCM) and Two-Speed Start-up. FSCM provides for
background monitoring of the peripheral clock and
automatic switchover in the event of its failure.
Two-Speed Start-up enables code to be executed
almost immediately on start-up, while the primary clock
source completes its start-up delays.
All of these features are enabled and configured by
setting the appropriate Configuration register bits.
Devices of the PIC18F85J90 family do not use persistent memory registers to store configuration information.
The configuration bytes are implemented as volatile
memory which means that configuration data must be
programmed each time the device is powered up.
When creating applications for these devices, users
should always specifically allocate the location of the
Flash Configuration Word for configuration data. This is
to make certain that program code is not stored in this
address when the code is compiled.
The volatile memory cells used for the Configuration
bits always reset to ‘1’ on Power-on Resets. For all
other types of Reset events, the previously
programmed values are maintained and used without
reloading from program memory.
The four Most Significant bits of CONFIG1H,
CONFIG2H and CONFIG3H in program memory
should also be ‘1111’. This makes these Configuration
Words appear to be NOP instructions in the remote
event that their locations are ever executed by
accident. Since Configuration bits are not implemented
in the corresponding locations, writing ‘1’s to these
locations has no effect on device operation.
To prevent inadvertent configuration changes during
code execution, all programmable Configuration bits
are write-once. After a bit is initially programmed during
a power cycle, it cannot be written to again. Changing
a device configuration requires that power to the device
be cycled.
TABLE 22-1:
Configuration Bits
The Configuration bits can be programmed (read as
‘0’), or left unprogrammed (read as ‘1’), to select
various device configurations. These bits are mapped
starting at program memory location 300000h. A
complete list is shown in Table 22-2. A detailed
explanation of the various bit functions is provided in
Register 22-1 through Register 22-5.
© 2007 Microchip Technology Inc.
CONSIDERATIONS FOR
CONFIGURING THE PIC18F85J90
FAMILY DEVICES
Configuration data is stored in the four words at the top
of the on-chip program memory space, known as the
Flash Configuration Words. It is stored in program
memory in the same order shown in Table 22-2, with
CONFIG1L at the lowest address and CONFIG3H at
the highest. The data is automatically loaded in the
proper Configuration registers during device power-up.
The oscillator can be configured for the application
depending on frequency, power, accuracy and cost. All
of the options are discussed in detail in Section 2.0
“Oscillator Configurations”.
22.1
22.1.1
Configuration
Byte
MAPPING OF THE FLASH
CONFIGURATION WORDS TO
THE CONFIGURATION
REGISTERS
Code Space
Address
Configuration
Register
Address
CONFIG1L
XXXF8h
300000h
CONFIG1H
XXXF9h
300001h
CONFIG2L
XXXFAh
300002h
CONFIG2H
XXXFBh
300003h
CONFIG3L
XXXFCh
300004h
CONFIG3H
XXXFDh
300005h
Legend: Unimplemented in PIC18F85J90 family
devices.
Preliminary
DS39770B-page 283
PIC18F85J90 FAMILY
TABLE 22-2:
CONFIGURATION BITS AND DEVICE IDs
File Name
300000h
CONFIG1L
Default/
Unprogrammed
Value(1)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DEBUG
XINST
STVREN
—
—
—
—
WDTEN
111- ---1
(2)
(2)
(2)
(2)
(3)
300001h
CONFIG1H
—
300002h
CONFIG2L
IESO
FCMEN
—
—
300003h
CONFIG2H
—(2)
—(2)
—(2)
—(2)
300005h
CONFIG3H
—(2)
—(2)
—(2)
—(2)
—
—
—
CCP2MX
3FFFFEh DEVID1
DEV2
DEV1
DEV0
REV4
REV3
REV2
REV1
REV0
xxxx xxxx(4)
3FFFFFh DEVID2
DEV10
DEV9
DEV8
DEV7
DEV6
DEV5
DEV4
DEV3
0000 10x1(4)
Legend:
Note 1:
2:
3:
4:
—
—
—
—
—
CP0
—
—
---- 01--
FOSC2
FOSC1
FOSC0
11-- -111
WDTPS3 WDTPS2 WDTPS1 WDTPS0
---- 1111
---- ---1
x = unknown, - = unimplemented. Shaded cells are unimplemented, read as ‘0’.
Values reflect the unprogrammed state as received from the factory and following Power-on Resets. In all other Reset
states, the configuration bytes maintain their previously programmed states.
The value of these bits in program memory should always be ‘1’. This ensures that the location is executed as a NOP if it
is accidentally executed.
This bit should always be maintained as ‘0’.
See Register 22-6 and Register 22-7 for DEVID values. These registers are read-only and cannot be programmed by
the user.
DS39770B-page 284
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 22-1:
CONFIG1L: CONFIGURATION REGISTER 1 LOW (BYTE ADDRESS 300000h)
R/WO-1
R/WO-1
R/WO-1
U-0
U-0
U-0
U-0
R/WO-1
DEBUG
XINST
STVREN
—
—
—
—
WDTEN
bit 7
bit 0
Legend:
R = Readable bit
WO = Write-Once bit
-n = Value when device is unprogrammed
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
DEBUG: Background Debugger Enable bit
1 = Background debugger disabled; RB6 and RB7 configured as general purpose I/O pins
0 = Background debugger enabled; RB6 and RB7 are dedicated to In-Circuit Debug
bit 6
XINST: Extended Instruction Set Enable bit
1 = Instruction set extension and Indexed Addressing mode enabled
0 = Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
bit 5
STVREN: Stack Overflow/Underflow Reset Enable bit
1 = Reset on stack overflow/underflow enabled
0 = Reset on stack overflow/underflow disabled
bit 4-1
Unimplemented: Read as ‘0’
bit 0
WDTEN: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled (control is placed on SWDTEN bit)
REGISTER 22-2:
CONFIG1H: CONFIGURATION REGISTER 1 HIGH (BYTE ADDRESS 300001h)
U-0
U-0
U-0
U-0
U-0
R/WO-1
U-0
U-0
—(1)
—(1)
—(1)
—(1)
—(2)
CP0
—
—
bit 7
bit 0
Legend:
R = Readable bit
WO = Write-Once bit
-n = Value when device is unprogrammed
‘1’ = Bit is set
bit 7-3
Unimplemented: Read as ‘0’
bit 2
CP0: Code Protection bit
1 = Program memory is not code-protected
0 = Program memory is code-protected
bit 1-0
Unimplemented: Read as ‘0’
Note 1:
2:
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
The value of these bits in program memory should always be ‘1’. This ensures that the location is
executed as a NOP if it is accidentally executed.
This bit should always be maintained as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 285
PIC18F85J90 FAMILY
REGISTER 22-3:
R/WO-1
IESO
bit 7
CONFIG2L: CONFIGURATION REGISTER 2 LOW (BYTE ADDRESS 300002h)
R/WO-1
U-0
U-0
U-0
R/WO-1
R/WO-1
R/WO-1
FCMEN
—
—
—
FOSC2
FOSC1
FOSC0
bit 0
Legend:
R = Readable bit
WO = Write-Once bit
-n = Value when device is unprogrammed
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
IESO: Two-Speed Start-up (Internal/External Oscillator Switchover) Control bit
1 = Two-Speed Start-up enabled
0 = Two-Speed Start-up disabled
bit 6
FCMEN: Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor enabled
0 = Fail-Safe Clock Monitor disabled
Unimplemented: Read as ‘0’
bit 5-3
bit 2-0
FOSC2:FOSC0: Oscillator Selection bits
111 = OSC1/OSC2 as primary; EC oscillator with CLKO function and software controlled
PLL (EC+PLL)
110 = OSC1/OSC2 as primary; EC oscillator with CLKO function (EC)
101 = OSC1/OSC2 as primary; HS oscillator with software controlled PLL (HS+PLL)
100 = OSC1/OSC2 as primary; HS oscillator (HS)
011 = INTOSC with CLKO as primary; port function on RA7; EC oscillator with CLKO function and
software controlled PLL (EC+PLL)
010 = INTOSC with CLKO as primary; port function on RA7; EC oscillator with CLKO function
001 = INTOSC as primary with port function on RA6/RA7; HS oscillator with software controlled
PLL (HS+PLL)
000 = INTOSC as primary with port function on RA6/RA7; HS oscillator (HS)
DS39770B-page 286
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
REGISTER 22-4:
CONFIG2H: CONFIGURATION REGISTER 2 HIGH (BYTE ADDRESS 300003h)
U-0
U-0
U-0
U-0
(1)
(1)
(1)
(1)
—
—
—
—
R/WO-1
R/WO-1
R/WO-1
R/WO-1
WDTPS3
WDTPS2
WDTPS1
WDTPS0
bit 0
bit 7
Legend:
R = Readable bit
WO = Write-Once bit
-n = Value when device is unprogrammed
bit 7-4
bit 3-0
Note 1:
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
Unimplemented: Read as ‘0’
WDTPS3:WDTPS0: Watchdog Timer Postscale Select bits
1111 = 1:32,768
1110 = 1:16,384
1101 = 1:8,192
1100 = 1:4,096
1011 = 1:2,048
1010 = 1:1,024
1001 = 1:512
1000 = 1:256
0111 = 1:128
0110 = 1:64
0101 = 1:32
0100 = 1:16
0011 = 1:8
0010 = 1:4
0001 = 1:2
0000 = 1:1
The value of these bits in program memory should always be ‘1’. This ensures that the location is
executed as a NOP if it is accidentally executed.
REGISTER 22-5:
CONFIG3H: CONFIGURATION REGISTER 3 HIGH (BYTE ADDRESS 300005h)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/WO-1
—(1)
—(1)
—(1)
—(1)
—
—
—
CCP2MX
bit 7
bit 0
Legend:
R = Readable bit
WO = Write-Once bit
-n = Value when device is unprogrammed
bit 7-1
Unimplemented: Read as ‘0’
bit 0
CCP2MX: CCP2 MUX bit
1 = CCP2 is multiplexed with RC1
0 = CCP2 is multiplexed with RE7
Note 1:
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
The value of these bits in program memory should always be ‘1’. This ensures that the location is
executed as a NOP if it is accidentally executed.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 287
PIC18F85J90 FAMILY
REGISTER 22-6:
DEVID1: DEVICE ID REGISTER 1 FOR PIC18F85J90 FAMILY DEVICES
R
R
R
R
R
R
R
R
DEV2
DEV1
DEV0
REV4
REV3
REV2
REV1
REV0
bit 7
bit 0
Legend:
R = Read-only bit
bit 7-5
DEV2:DEV0: Device ID bits
111 = PIC18F85J90
101 = PIC18F84J90
100 = PIC18F83J90
011 = PIC18F65J90
001 = PIC18F64J90
000 = PIC18F63J90
bit 4-0
REV4:REV0: Revision ID bits
These bits are used to indicate the device revision.
REGISTER 22-7:
DEVID2: DEVICE ID REGISTER 2 FOR PIC18F85J90 FAMILY DEVICES
R
R
R
R
R
R
R
R
DEV10(1)
DEV9(1)
DEV8(1)
DEV7(1)
DEV6(1)
DEV5(1)
DEV4(1)
DEV3(1)
bit 7
bit 0
Legend:
R = Read-only bit
bit 7-0
Note 1:
DEV10:DEV3: Device ID bits(1)
These bits are used with the DEV2:DEV0 bits in the Device ID Register 1 to identify the part number.
0011 1000 = PIC18F6XJ90/8XJ90 devices
The values for DEV10:DEV3 may be shared with other device families. The specific device is always
identified by using the entire DEV10:DEV0 bit sequence.
DS39770B-page 288
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
22.2
Watchdog Timer (WDT)
Note 1: The CLRWDT and SLEEP instructions
clear the WDT and postscaler counts
when executed.
For PIC18F85J90 family devices, the WDT is driven by
the INTRC oscillator. When the WDT is enabled, the
clock source is also enabled. The nominal WDT period is
4 ms and has the same stability as the INTRC oscillator.
The 4 ms period of the WDT is multiplied by a 16-bit
postscaler. Any output of the WDT postscaler is
selected by a multiplexor, controlled by the WDTPS bits
in Configuration Register 2H. Available periods range
from 4 ms to 131.072 seconds (2.18 minutes). The
WDT and postscaler are cleared whenever a SLEEP or
CLRWDT instruction is executed, or a clock failure
(primary or Timer1 oscillator) has occurred.
FIGURE 22-1:
2: When a CLRWDT instruction is executed,
the postscaler count will be cleared.
22.2.1
CONTROL REGISTER
The WDTCON register (Register 22-8) is a readable
and writable register. The SWDTEN bit enables or disables WDT operation. This allows software to override
the WDTEN Configuration bit and enable the WDT only
if it has been disabled by the Configuration bit.
WDT BLOCK DIAGRAM
Enable WDT
SWDTEN
INTRC Control
WDT Counter
Wake-up from
Power-Managed
Modes
÷128
INTRC Oscillator
CLRWDT
Programmable Postscaler
1:1 to 1:32,768
All Device Resets
WDT
4
WDTPS3:WDTPS0
WDT
Reset
Reset
Sleep
REGISTER 22-8:
WDTCON: WATCHDOG TIMER CONTROL REGISTER
R/W-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
REGSLP(1)
—
—
—
—
—
—
SWDTEN(2)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
REGSLP: Voltage Regulator Low-Power Operation Enable bit(1)
1 = On-chip regulator enters low-power operation when device enters Sleep mode
0 = On-chip regulator continues to operate normally in Sleep mode
bit 6-1
Unimplemented: Read as ‘0’
bit 0
SWDTEN: Software Controlled Watchdog Timer Enable bit(2)
1 = Watchdog Timer is on
0 = Watchdog Timer is off
Note 1:
2:
The REGSLP bit is automatically cleared when a Low-Voltage Detect condition occurs.
This bit has no effect if the Configuration bit, WDTEN, is enabled.
TABLE 22-3:
Name
RCON
WDTCON
SUMMARY OF WATCHDOG TIMER REGISTERS
Bit 0
Reset Values
on page
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
IPEN
—
—
RI
TO
PD
POR
BOR
52
REGSLP
—
—
—
—
—
—
SWDTEN
52
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Watchdog Timer.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 289
PIC18F85J90 FAMILY
22.3
FIGURE 22-2:
On-Chip Voltage Regulator
All of the PIC18F85J90 family devices power their core
digital logic at a nominal 2.5V. For designs that are
required to operate at a higher typical voltage, such as
3.3V, all devices in the PIC18F85J90 family incorporate
an on-chip regulator that allows the device to run its
core logic from VDD.
The regulator is controlled by the ENVREG pin. Tying
VDD to the pin enables the regulator, which in turn, provides power to the core from the other VDD pins. When
the regulator is enabled, a low-ESR filter capacitor
must be connected to the VDDCORE/VCAP pin
(Figure 22-2). This helps to maintain the stability of the
regulator. The recommended value for the filter capacitor is provided in Section 25.3 “DC Characteristics:
PIC18F84J90 Family (Industrial)”.
Regulator Enabled (ENVREG tied to VDD):
3.3V
PIC18F85J90
VDD
ENVREG
VDDCORE/VCAP
CF
VSS
Regulator Disabled (ENVREG tied to ground):
2.5V(1)
If ENVREG is tied to VSS, the regulator is disabled. In
this case, separate power for the core logic at a nominal 2.5V must be supplied to the device on the
VDDCORE/VCAP pin to run the I/O pins at higher voltage
levels, typically 3.3V. Alternatively, the VDDCORE/VCAP
and VDD pins can be tied together to operate at a lower
nominal voltage. Refer to Figure 22-2 for possible
configurations.
22.3.1
CONNECTIONS FOR THE
ON-CHIP REGULATOR
3.3V(1)
PIC18F85J90
VDD
ENVREG
VDDCORE/VCAP
VSS
VOLTAGE REGULATION AND LOW
VOLTAGE DETECTION
When it is enabled, the on-chip regulator provides a
constant voltage of 2.5V nominal to the digital core
logic. The regulator can provide this level from a Vdd of
about 2.5V, all the way up to the device’s Vddmax. It
does not have the capability to boost Vdd levels below
2.5V.
Regulator Disabled (VDD tied to VDDCORE):
2.5V(1)
PIC18F85J90
VDD
ENVREG
VDDCORE/VCAP
In order to prevent “brown-out” conditions, when the
voltage drops too low for the regulator, the regulator
enters Tracking mode. In Tracking mode, the regulator
output follows VDD, with a typical voltage drop of
100 mV.
The on-chip regulator includes a simple Low-Voltage
Detect (LVD) circuit. If Vdd drops too low to maintain
approximately 2.45V on Vddcore, the circuit sets the
Low-Voltage Detect Interrupt Flag, LVDIF (PIR2<2>)
and clears the REGSLP (WDTCON<7>) bit, if it was
set.
VSS
Note 1: These are typical operating voltages. Refer
to Section 25.1 “DC Characteristics:
Supply Voltage” for the full operating
ranges of VDD and VDDCORE.
This can be used to generate an interrupt and put the
application into a low-power operational mode, or trigger an orderly shutdown. Low-Voltage Detection is only
available when the regulator is enabled.
DS39770B-page 290
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
22.3.2
ON-CHIP REGULATOR AND BOR
The REGSLP bit is automatically cleared by hardware
when a Low-Voltage Detect condition occurs. The
REGSLP bit can be set again in software, which would
continue to keep the voltage regulator in Low-Power
mode. This, however, is not recommended if any write
operations to the Flash will be performed.
When the on-chip regulator is enabled, PIC18F85J90
family devices also have a simple Brown-out Reset
capability. If the voltage supplied to the regulator falls to
a level that is inadequate to maintain a regulated output
for full-speed operation, the regulator Reset circuitry
will generate a Brown-out Reset. This event is captured
by the BOR flag bit (RCON<0>).
22.4
The Two-Speed Start-up feature helps to minimize the
latency period, from oscillator start-up to code execution, by allowing the microcontroller to use the INTRC
oscillator as a clock source until the primary clock
source is available. It is enabled by setting the IESO
Configuration bit.
The operation of the BOR is described in more detail in
Section 4.4 “Brown-out Reset (BOR)” and
Section 4.4.1 “Detecting BOR”.
22.3.3
POWER-UP REQUIREMENTS
The on-chip regulator is designed to meet the power-up
requirements for the device. If the application does not
use the regulator, then strict power-up conditions must
be adhered to. While powering up, VDDCORE must
never exceed VDD by 0.3 volts.
22.3.4
Two-Speed Start-up should be enabled only if the
primary oscillator mode is HS or HSPLL
(Crystal-Based) modes. Since the EC and ECPLL
modes do not require an OST start-up delay,
Two-Speed Start-up should be disabled.
OPERATION IN SLEEP MODE
When enabled, Resets and wake-ups from Sleep mode
cause the device to configure itself to run from the internal oscillator block as the clock source, following the
time-out of the Power-up Timer after a Power-on Reset
is enabled. This allows almost immediate code
execution while the primary oscillator starts and the
OST is running. Once the OST times out, the device
automatically switches to PRI_RUN mode.
When enabled, the on-chip regulator always consumes
a small incremental amount of current over IDD. This
includes when the device is in Sleep mode, even
though the core digital logic does not require power. To
provide additional savings in applications where power
resources are critical, the regulator can be configured
to automatically disable itself whenever the device
goes into Sleep mode. This feature is controlled by the
REGSLP bit (WDTCON<7>). Setting this bit disables
the regulator in Sleep mode, and reduces its current
consumption to a minimum.
In all other power-managed modes, Two-Speed
Start-up is not used. The device will be clocked by the
currently selected clock source until the primary clock
source becomes available. The setting of the IESO bit
is ignored.
Substantial Sleep mode power savings can be
obtained by setting the REGSLP bit, but device
wake-up time will increase in order to ensure the
regulator has enough time to stabilize.
FIGURE 22-3:
Two-Speed Start-up
TIMING TRANSITION FOR TWO-SPEED START-UP (INTRC TO HSPLL)
Q1
Q2
Q3
Q4
Q2 Q3 Q4 Q1 Q2 Q3
Q1
INTRC
OSC1
TOST(1)
TPLL(1)
1
PLL Clock
Output
2
n-1 n
Clock
Transition
CPU Clock
Peripheral
Clock
Program
Counter
PC
Wake from Interrupt Event
Note 1:
PC + 2
PC + 4
PC + 6
OSTS bit Set
TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 291
PIC18F85J90 FAMILY
22.4.1
SPECIAL CONSIDERATIONS FOR
USING TWO-SPEED START-UP
While using the INTRC oscillator in Two-Speed
Start-up, the device still obeys the normal command
sequences for entering power-managed modes,
including serial SLEEP instructions (refer to
Section 3.1.4 “Multiple Sleep Commands”). In practice, this means that user code can change the
SCS1:SCS0 bit settings or issue SLEEP instructions
before the OST times out. This would allow an application to briefly wake-up, perform routine “housekeeping”
tasks and return to Sleep before the device starts to
operate from the primary oscillator.
User code can also check if the primary clock source is
currently providing the device clocking by checking the
status of the OSTS bit (OSCCON<3>). If the bit is set,
the primary oscillator is providing the clock. Otherwise,
the internal oscillator block is providing the clock during
wake-up from Reset or Sleep mode.
22.5
Fail-Safe Clock Monitor
Clock failure is tested for on the falling edge of the
sample clock. If a sample clock falling edge occurs
while CM is still set, a clock failure has been detected
(Figure 22-5). This causes the following:
• the FSCM generates an oscillator fail interrupt by
setting bit, OSCFIF (PIR2<7>);
• the device clock source is switched to the internal
oscillator block (OSCCON is not updated to show
the current clock source – this is the fail-safe
condition); and
• the WDT is reset.
During switchover, the postscaler frequency from the
internal oscillator block may not be sufficiently stable
for timing sensitive applications. In these cases, it may
be desirable to select another clock configuration and
enter an alternate power-managed mode. This can be
done to attempt a partial recovery or execute a
controlled shutdown. See Section 3.1.4 “Multiple
Sleep Commands” and Section 22.4.1 “Special
Considerations for Using Two-Speed Start-up” for
more details.
The Fail-Safe Clock Monitor (FSCM) allows the
microcontroller to continue operation in the event of an
external oscillator failure by automatically switching the
device clock to the internal oscillator block. The FSCM
function is enabled by setting the FCMEN Configuration
bit.
The FSCM will detect failures of the primary or secondary
clock sources only. If the internal oscillator block fails, no
failure would be detected, nor would any action be
possible.
When FSCM is enabled, the INTRC oscillator runs at
all times to monitor clocks to peripherals and provides
a backup clock in the event of a clock failure. Clock
monitoring (shown in Figure 22-4) is accomplished by
creating a sample clock signal which is the INTRC output divided by 64. This allows ample time between
FSCM sample clocks for a peripheral clock edge to
occur. The peripheral device clock and the sample
clock are presented as inputs to the Clock Monitor latch
(CM). The CM is set on the falling edge of the device
clock source but cleared on the rising edge of the
sample clock.
Both the FSCM and the WDT are clocked by the
INTRC oscillator. Since the WDT operates with a
separate divider and counter, disabling the WDT has
no effect on the operation of the INTRC oscillator when
the FSCM is enabled.
FIGURE 22-4:
FSCM BLOCK DIAGRAM
Clock Monitor
Latch (CM)
(edge-triggered)
Peripheral
Clock
INTRC
Source
(32 μs)
÷ 64
S
Q
C
Q
22.5.1
FSCM AND THE WATCHDOG TIMER
As already noted, the clock source is switched to the
INTRC clock when a clock failure is detected; this may
mean a substantial change in the speed of code execution. If the WDT is enabled with a small prescale value,
a decrease in clock speed allows a WDT time-out to
occur and a subsequent device Reset. For this reason,
Fail-Safe Clock Monitor events also reset the WDT and
postscaler, allowing it to start timing from when execution speed was changed and decreasing the likelihood
of an erroneous time-out.
If the interrupt is disabled, subsequent interrupts while
in Idle mode will cause the CPU to begin executing
instructions while being clocked by the INTRC source.
488 Hz
(2.048 ms)
Clock
Failure
Detected
DS39770B-page 292
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 22-5:
FSCM TIMING DIAGRAM
Sample Clock
Oscillator
Failure
Device
Clock
Output
CM Output
(Q)
Failure
Detected
OSCFIF
CM Test
CM Test
Note:
22.5.2
The device clock is normally at a much higher frequency than the sample clock. The relative frequencies in
this example have been chosen for clarity.
EXITING FAIL-SAFE OPERATION
The fail-safe condition is terminated by either a device
Reset or by entering a power-managed mode. On
Reset, the controller starts the primary clock source
specified in Configuration Register 2H (with any
required start-up delays that are required for the oscillator mode, such as OST or PLL timer). The INTRC
oscillator provides the device clock until the primary
clock source becomes ready (similar to a Two-Speed
Start-up). The clock source is then switched to the
primary clock (indicated by the OSTS bit in the
OSCCON register becoming set). The Fail-Safe Clock
Monitor then resumes monitoring the peripheral clock.
The primary clock source may never become ready
during start-up. In this case, operation is clocked by the
INTOSC multiplexor. The OSCCON register will remain
in its Reset state until a power-managed mode is
entered.
22.5.3
CM Test
22.5.4
The FSCM is designed to detect oscillator failure at any
point after the device has exited Power-on Reset
(POR) or low-power Sleep mode. When the primary
device clock is either EC or INTRC mode, monitoring
can begin immediately following these events.
For HS or HSPLL modes, the situation is somewhat different. Since the oscillator may require a start-up time
considerably longer than the FSCM sample clock time,
a false clock failure may be detected. To prevent this,
the internal oscillator block is automatically configured
as the device clock and functions until the primary clock
is stable (the OST and PLL timers have timed out). This
is identical to Two-Speed Start-up mode. Once the
primary clock is stable, the INTRC returns to its role as
the FSCM source.
Note:
FSCM INTERRUPTS IN
POWER-MANAGED MODES
By entering a power-managed mode, the clock
multiplexor selects the clock source selected by the
OSCCON register. Fail-Safe Clock Monitoring of the
power-managed clock source resumes in the
power-managed mode.
If an oscillator failure occurs during power-managed
operation, the subsequent events depend on whether
or not the oscillator failure interrupt is enabled. If
enabled (OSCFIF = 1), code execution will be clocked
by the INTRC multiplexor. An automatic transition back
to the failed clock source will not occur.
© 2007 Microchip Technology Inc.
POR OR WAKE-UP FROM SLEEP
The same logic that prevents false
oscillator failure interrupts on POR, or
wake from Sleep, will also prevent the
detection of the oscillator’s failure to start
at all following these events. This can be
avoided by monitoring the OSTS bit and
using a timing routine to determine if the
oscillator is taking too long to start. Even
so, no oscillator failure interrupt will be
flagged.
As noted in Section 22.4.1 “Special Considerations
for Using Two-Speed Start-up”, it is also possible to
select another clock configuration and enter an alternate
power-managed mode while waiting for the primary
clock to become stable. When the new power-managed
mode is selected, the primary clock is disabled.
Preliminary
DS39770B-page 293
PIC18F85J90 FAMILY
22.6
Program Verification and
Code Protection
22.7
For all devices in the PIC18F85J90 family of devices,
the on-chip program memory space is treated as a
single block. Code protection for this block is controlled
by one Configuration bit, CP0. This bit inhibits external
reads and writes to the program memory space. It has
no direct effect in normal execution mode.
22.6.1
CONFIGURATION REGISTER
PROTECTION
The Configuration registers are protected against
untoward changes or reads in two ways. The primary
protection is the write-once feature of the Configuration
bits which prevents reconfiguration once the bit has
been programmed during a power cycle. To safeguard
against unpredictable events, Configuration bit
changes resulting from individual cell-level disruptions
(such as ESD events) will cause a parity error and
trigger a device Reset.
The data for the Configuration registers is derived from
the Flash Configuration Words in program memory.
When the CP0 bit set, the source data for device
configuration is also protected as a consequence.
DS39770B-page 294
In-Circuit Serial Programming
PIC18F85J90 family microcontrollers can be serially
programmed while in the end application circuit. This is
simply done with two lines for clock and data and three
other lines for power, ground and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware or a custom
firmware to be programmed.
22.8
In-Circuit Debugger
When the DEBUG Configuration bit is programmed to
a ‘0’, the In-Circuit Debugger functionality is enabled.
This function allows simple debugging functions when
used with MPLAB® IDE. When the microcontroller has
this feature enabled, some resources are not available
for general use. Table 22-4 shows which resources are
required by the background debugger.
TABLE 22-4:
DEBUGGER RESOURCES
I/O pins:
RB6, RB7
Stack:
2 levels
Program Memory:
512 bytes
Data Memory:
10 bytes
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
23.0
INSTRUCTION SET SUMMARY
The PIC18F85J90 family of devices incorporate the
standard set of 75 PIC18 core instructions, as well as
an extended set of 8 new instructions for the optimization of code that is recursive or that utilizes a software
stack. The extended set is discussed later in this
section.
23.1
Standard Instruction Set
The standard PIC18 instruction set adds many
enhancements to the previous PIC® MCU instruction
sets, while maintaining an easy migration from these
PIC MCU instruction sets. Most instructions are a
single program memory word (16 bits), but there are
four instructions that require two program memory
locations.
Each single-word instruction is a 16-bit word divided
into an opcode, which specifies the instruction type and
one or more operands, which further specify the
operation of the instruction.
The instruction set is highly orthogonal and is grouped
into four basic categories:
•
•
•
•
Byte-oriented operations
Bit-oriented operations
Literal operations
Control operations
The PIC18 instruction set summary in Table 23-2 lists
byte-oriented, bit-oriented, literal and control
operations. Table 23-1 shows the opcode field
descriptions.
Most byte-oriented instructions have three operands:
1.
2.
3.
The file register (specified by ‘f’)
The destination of the result (specified by ‘d’)
The accessed memory (specified by ‘a’)
The file register designator ‘f’ specifies which file register is to be used by the instruction. The destination
designator ‘d’ specifies where the result of the
operation is to be placed. If ‘d’ is zero, the result is
placed in the WREG register. If ‘d’ is one, the result is
placed in the file register specified in the instruction.
All bit-oriented instructions have three operands:
1.
2.
3.
The file register (specified by ‘f’)
The bit in the file register (specified by ‘b’)
The accessed memory (specified by ‘a’)
The literal instructions may use some of the following
operands:
• A literal value to be loaded into a file register
(specified by ‘k’)
• The desired FSR register to load the literal value
into (specified by ‘f’)
• No operand required
(specified by ‘—’)
The control instructions may use some of the following
operands:
• A program memory address (specified by ‘n’)
• The mode of the CALL or RETURN instructions
(specified by ‘s’)
• The mode of the table read and table write
instructions (specified by ‘m’)
• No operand required
(specified by ‘—’)
All instructions are a single word, except for four
double-word instructions. These instructions were
made double-word to contain the required information
in 32 bits. In the second word, the 4 MSbs are ‘1’s. If
this second word is executed as an instruction (by
itself), it will execute as a NOP.
All single-word instructions are executed in a single
instruction cycle, unless a conditional test is true or the
program counter is changed as a result of the instruction. In these cases, the execution takes two instruction
cycles with the additional instruction cycle(s) executed
as a NOP.
The double-word instructions execute in two instruction
cycles.
One instruction cycle consists of four oscillator periods.
Thus, for an oscillator frequency of 4 MHz, the normal
instruction execution time is 1 μs. If a conditional test is
true, or the program counter is changed as a result of
an instruction, the instruction execution time is 2 μs.
Two-word branch instructions (if true) would take 3 μs.
Figure 23-1 shows the general formats that the instructions can have. All examples use the convention ‘nnh’
to represent a hexadecimal number.
The Instruction Set Summary, shown in Table 23-2,
lists the standard instructions recognized by the
Microchip MPASMTM Assembler.
Section 23.1.1 “Standard Instruction Set” provides
a description of each instruction.
The bit field designator ‘b’ selects the number of the bit
affected by the operation, while the file register designator ‘f’ represents the number of the file in which the
bit is located.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 295
PIC18F85J90 FAMILY
TABLE 23-1:
OPCODE FIELD DESCRIPTIONS
Field
Description
a
RAM access bit:
a = 0: RAM location in Access RAM (BSR register is ignored)
a = 1: RAM bank is specified by BSR register
bbb
Bit address within an 8-bit file register (0 to 7).
BSR
Bank Select Register. Used to select the current RAM bank.
C, DC, Z, OV, N
ALU Status bits: Carry, Digit Carry, Zero, Overflow, Negative.
d
Destination select bit:
d = 0: store result in WREG
d = 1: store result in file register f
dest
Destination: either the WREG register or the specified register file location.
f
8-bit Register file address (00h to FFh), or 2-bit FSR designator (0h to 3h).
fs
12-bit Register file address (000h to FFFh). This is the source address.
fd
12-bit Register file address (000h to FFFh). This is the destination address.
GIE
Global Interrupt Enable bit.
k
Literal field, constant data or label (may be either an 8-bit, 12-bit or a 20-bit value).
label
Label name.
mm
The mode of the TBLPTR register for the table read and table write instructions.
Only used with table read and table write instructions:
*
No Change to register (such as TBLPTR with table reads and writes)
*+
Post-Increment register (such as TBLPTR with table reads and writes)
*-
Post-Decrement register (such as TBLPTR with table reads and writes)
Pre-Increment register (such as TBLPTR with table reads and writes)
+*
n
The relative address (2’s complement number) for relative branch instructions or the direct address for
Call/Branch and Return instructions.
PC
Program Counter.
PCL
Program Counter Low Byte.
PCH
Program Counter High Byte.
PCLATH
Program Counter High Byte Latch.
PCLATU
Program Counter Upper Byte Latch.
PD
Power-Down bit.
PRODH
Product of Multiply High Byte.
PRODL
Product of Multiply Low Byte.
s
Fast Call/Return mode select bit:
s = 0: do not update into/from shadow registers
s = 1: certain registers loaded into/from shadow registers (Fast mode)
TBLPTR
21-bit Table Pointer (points to a Program Memory location).
TABLAT
8-bit Table Latch.
TO
Time-out bit.
TOS
Top-of-Stack.
u
Unused or Unchanged.
WDT
Watchdog Timer.
WREG
Working register (accumulator).
x
Don’t care (‘0’ or ‘1’). The assembler will generate code with x = 0. It is the recommended form of use for
compatibility with all Microchip software tools.
zs
7-bit offset value for Indirect Addressing of register files (source).
7-bit offset value for Indirect Addressing of register files (destination).
zd
{
}
Optional argument.
[text]
Indicates an Indexed Address.
(text)
The contents of text.
[expr]<n>
Specifies bit n of the register indicated by the pointer expr.
→
Assigned to.
< >
Register bit field.
∈
In the set of.
italics
User-defined term (font is Courier).
DS39770B-page 296
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 23-1:
GENERAL FORMAT FOR INSTRUCTIONS
Byte-oriented file register operations
15
10
9
OPCODE
Example Instruction
8 7
d
0
a
ADDWF MYREG, W, B
f (FILE #)
d = 0 for result destination to be WREG register
d = 1 for result destination to be file register (f)
a = 0 to force Access Bank
a = 1 for BSR to select bank
f = 8-bit file register address
Byte to Byte move operations (2-word)
15
12 11
0
OPCODE
15
f (Source FILE #)
12 11
MOVFF MYREG1, MYREG2
0
f (Destination FILE #)
1111
f = 12-bit file register address
Bit-oriented file register operations
15
12 11
9 8 7
0
OPCODE b (BIT #) a
BSF MYREG, bit, B
f (FILE #)
b = 3-bit position of bit in file register (f)
a = 0 to force Access Bank
a = 1 for BSR to select bank
f = 8-bit file register address
Literal operations
15
8
7
0
OPCODE
MOVLW 7Fh
k (literal)
k = 8-bit immediate value
Control operations
CALL, GOTO and Branch operations
15
8 7
0
OPCODE
15
GOTO Label
n<7:0> (literal)
12 11
0
n<19:8> (literal)
1111
n = 20-bit immediate value
15
8 7
OPCODE
15
S
0
CALL MYFUNC
n<7:0> (literal)
12 11
0
n<19:8> (literal)
1111
S = Fast bit
15
11 10
OPCODE
15
0
8 7
OPCODE
© 2007 Microchip Technology Inc.
BRA MYFUNC
n<10:0> (literal)
0
n<7:0> (literal)
Preliminary
BC MYFUNC
DS39770B-page 297
PIC18F85J90 FAMILY
TABLE 23-2:
PIC18F85J90 FAMILY INSTRUCTION SET
Mnemonic,
Operands
16-bit Instruction Word
Description
Cycles
MSb
LSb
Status
Affected
Notes
BYTE-ORIENTED OPERATIONS
ADDWF
ADDWFC
ANDWF
CLRF
COMF
CPFSEQ
CPFSGT
CPFSLT
DECF
DECFSZ
DCFSNZ
INCF
INCFSZ
INFSNZ
IORWF
MOVF
MOVFF
f, d, a
f, d, a
f, d, a
f, a
f, d, a
f, a
f, a
f, a
f, d, a
f, d, a
f, d, a
f, d, a
f, d, a
f, d, a
f, d, a
f, d, a
fs, fd
MOVWF
MULWF
NEGF
RLCF
RLNCF
RRCF
RRNCF
SETF
SUBFWB
f, a
f, a
f, a
f, d, a
f, d, a
f, d, a
f, d, a
f, a
f, d, a
SUBWF
SUBWFB
f, d, a
f, d, a
SWAPF
TSTFSZ
XORWF
f, d, a
f, a
f, d, a
Note 1:
2:
3:
4:
Add WREG and f
Add WREG and Carry bit to f
AND WREG with f
Clear f
Complement f
Compare f with WREG, skip =
Compare f with WREG, skip >
Compare f with WREG, skip <
Decrement f
Decrement f, Skip if 0
Decrement f, Skip if Not 0
Increment f
Increment f, Skip if 0
Increment f, Skip if Not 0
Inclusive OR WREG with f
Move f
Move fs (source) to 1st word
fd (destination) 2nd word
Move WREG to f
Multiply WREG with f
Negate f
Rotate Left f through Carry
Rotate Left f (No Carry)
Rotate Right f through Carry
Rotate Right f (No Carry)
Set f
Subtract f from WREG with
borrow
Subtract WREG from f
Subtract WREG from f with
borrow
Swap nibbles in f
Test f, skip if 0
Exclusive OR WREG with f
1
1
1
1
1
1 (2 or 3)
1 (2 or 3)
1 (2 or 3)
1
1 (2 or 3)
1 (2 or 3)
1
1 (2 or 3)
1 (2 or 3)
1
1
2
C, DC, Z, OV, N
C, DC, Z, OV, N
Z, N
Z
Z, N
None
None
None
C, DC, Z, OV, N
None
None
C, DC, Z, OV, N
None
None
Z, N
Z, N
None
1, 2
1, 2
1,2
2
1, 2
4
4
1, 2
1, 2, 3, 4
1, 2, 3, 4
1, 2
1, 2, 3, 4
4
1, 2
1, 2
1
1
1
1
1
1
1
1
1
1
0010
0010
0001
0110
0001
0110
0110
0110
0000
0010
0100
0010
0011
0100
0001
0101
1100
1111
0110
0000
0110
0011
0100
0011
0100
0110
0101
01da
00da
01da
101a
11da
001a
010a
000a
01da
11da
11da
10da
11da
10da
00da
00da
ffff
ffff
111a
001a
110a
01da
01da
00da
00da
100a
01da
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
1
1
0101 11da
0101 10da
ffff
ffff
ffff C, DC, Z, OV, N 1, 2
ffff C, DC, Z, OV, N
1
0011 10da
1 (2 or 3) 0110 011a
1
0001 10da
ffff
ffff
ffff
ffff None
ffff None
ffff Z, N
None
None
1, 2
C, DC, Z, OV, N
C, Z, N
1, 2
Z, N
C, Z, N
Z, N
None
1, 2
C, DC, Z, OV, N
4
1, 2
When a PORT register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that
value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is
driven low by an external device, the data will be written back with a ‘0’.
If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared
if assigned.
If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second
cycle is executed as a NOP.
Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP
unless the first word of the instruction retrieves the information embedded in these 16-bits. This ensures that all
program memory locations have a valid instruction.
DS39770B-page 298
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 23-2:
PIC18F85J90 FAMILY INSTRUCTION SET (CONTINUED)
16-bit Instruction Word
Mnemonic,
Operands
Description
Cycles
MSb
LSb
Status
Affected
Notes
BIT-ORIENTED OPERATIONS
BCF
BSF
BTFSC
BTFSS
BTG
f, b, a
f, b, a
f, b, a
f, b, a
f, b, a
Bit Clear f
Bit Set f
Bit Test f, Skip if Clear
Bit Test f, Skip if Set
Bit Toggle f
1
1
1 (2 or 3)
1 (2 or 3)
1
1001
1000
1011
1010
0111
bbba
bbba
bbba
bbba
bbba
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
None
None
None
None
None
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
2
1 (2)
2
0010
0110
0011
0111
0101
0001
0100
0nnn
0000
110s
kkkk
0000
0000
1111
kkkk
0000
xxxx
0000
0000
1nnn
0000
0000
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
kkkk
kkkk
0000
0000
kkkk
kkkk
0000
xxxx
0000
0000
nnnn
1111
0001
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
kkkk
kkkk
0100
0111
kkkk
kkkk
0000
xxxx
0110
0101
nnnn
1111
000s
None
None
None
None
None
None
None
None
None
None
1
1
1
1
2
1
2
1110
1110
1110
1110
1110
1110
1110
1101
1110
1110
1111
0000
0000
1110
1111
0000
1111
0000
0000
1101
0000
0000
2
2
1
0000 1100
0000 0000
0000 0000
kkkk
0001
0000
1, 2
1, 2
3, 4
3, 4
1, 2
CONTROL OPERATIONS
BC
BN
BNC
BNN
BNOV
BNZ
BOV
BRA
BZ
CALL
n
n
n
n
n
n
n
n
n
n, s
CLRWDT
DAW
GOTO
—
—
n
NOP
NOP
POP
PUSH
RCALL
RESET
RETFIE
—
—
—
—
n
s
Branch if Carry
Branch if Negative
Branch if Not Carry
Branch if Not Negative
Branch if Not Overflow
Branch if Not Zero
Branch if Overflow
Branch Unconditionally
Branch if Zero
Call subroutine 1st word
2nd word
Clear Watchdog Timer
Decimal Adjust WREG
Go to address 1st word
2nd word
No Operation
No Operation
Pop top of return stack (TOS)
Push top of return stack (TOS)
Relative Call
Software device Reset
Return from interrupt enable
RETLW
RETURN
SLEEP
k
s
—
Return with literal in WREG
Return from Subroutine
Go into Standby mode
Note 1:
2:
3:
4:
1
1
2
TO, PD
C
None
None
None
None
None
None
All
GIE/GIEH,
PEIE/GIEL
kkkk None
001s None
0011 TO, PD
4
When a PORT register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that
value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is
driven low by an external device, the data will be written back with a ‘0’.
If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared
if assigned.
If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second
cycle is executed as a NOP.
Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP
unless the first word of the instruction retrieves the information embedded in these 16-bits. This ensures that all
program memory locations have a valid instruction.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 299
PIC18F85J90 FAMILY
TABLE 23-2:
PIC18F85J90 FAMILY INSTRUCTION SET (CONTINUED)
16-bit Instruction Word
Mnemonic,
Operands
Description
Cycles
MSb
LSb
Status
Affected
Notes
LITERAL OPERATIONS
ADDLW
ANDLW
IORLW
LFSR
k
k
k
f, k
MOVLB
MOVLW
MULLW
RETLW
SUBLW
XORLW
k
k
k
k
k
k
Add literal and WREG
AND literal with WREG
Inclusive OR literal with WREG
Move literal (12-bit) 2nd word
to FSR(f)
1st word
Move literal to BSR<3:0>
Move literal to WREG
Multiply literal with WREG
Return with literal in WREG
Subtract WREG from literal
Exclusive OR literal with WREG
1
1
1
2
1
1
1
2
1
1
0000
0000
0000
1110
1111
0000
0000
0000
0000
0000
0000
1111
1011
1001
1110
0000
0001
1110
1101
1100
1000
1010
kkkk
kkkk
kkkk
00ff
kkkk
0000
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
C, DC, Z, OV, N
Z, N
Z, N
None
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
1000
1001
1010
1011
1100
1101
1110
1111
None
None
None
None
None
None
None
None
None
None
None
None
C, DC, Z, OV, N
Z, N
DATA MEMORY ↔ PROGRAM MEMORY OPERATIONS
TBLRD*
TBLRD*+
TBLRD*TBLRD+*
TBLWT*
TBLWT*+
TBLWT*TBLWT+*
Note 1:
2:
3:
4:
Table Read
2
Table Read with post-increment
Table Read with post-decrement
Table Read with pre-increment
Table Write
2
Table Write with post-increment
Table Write with post-decrement
Table Write with pre-increment
When a PORT register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that
value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is
driven low by an external device, the data will be written back with a ‘0’.
If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared
if assigned.
If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second
cycle is executed as a NOP.
Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP
unless the first word of the instruction retrieves the information embedded in these 16-bits. This ensures that all
program memory locations have a valid instruction.
DS39770B-page 300
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
23.1.1
STANDARD INSTRUCTION SET
ADDLW
ADD Literal to W
ADDWF
ADD W to f
Syntax:
ADDLW
Syntax:
ADDWF
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(W) + (f) → dest
Status Affected:
N, OV, C, DC, Z
k
Operands:
0 ≤ k ≤ 255
Operation:
(W) + k → W
Status Affected:
N, OV, C, DC, Z
Encoding:
0000
1111
kkkk
kkkk
Description:
The contents of W are added to the
8-bit literal ‘k’ and the result is placed in
W.
Words:
1
Cycles:
1
Encoding:
0010
Description:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write to
W
Example:
ADDLW
01da
ffff
ffff
Add W to register ‘f’. If ‘d’ is ‘0’, the
result is stored in W. If ‘d’ is ‘1’, the
result is stored back in register ‘f’
(default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
15h
Before Instruction
W
= 10h
After Instruction
W =
25h
f {,d {,a}}
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
ADDWF
Before Instruction
W
=
REG
=
After Instruction
W
=
REG
=
Note:
REG, 0, 0
17h
0C2h
0D9h
0C2h
All PIC18 instructions may take an optional label argument preceding the instruction mnemonic for use in
symbolic addressing. If a label is used, the instruction format then becomes: {label} instruction argument(s).
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 301
PIC18F85J90 FAMILY
ADDWFC
ADD W and Carry bit to f
ANDLW
AND Literal with W
Syntax:
ADDWFC
Syntax:
ANDLW
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
f {,d {,a}}
(W) + (f) + (C) → dest
Operation:
Status Affected:
Encoding:
0010
Description:
00da
Operands:
0 ≤ k ≤ 255
Operation:
(W) .AND. k → W
Status Affected:
N, Z
Encoding:
N,OV, C, DC, Z
ffff
ffff
Add W, the Carry flag and data memory
location ‘f’. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed in data memory location ‘f’.
Words:
1
Cycles:
1
0000
1011
kkkk
kkkk
Description:
The contents of W are ANDed with the
8-bit literal ‘k’. The result is placed in W.
Words:
1
Cycles:
1
Q Cycle Activity:
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
k
Q1
Q2
Q3
Q4
Decode
Read literal
‘k’
Process
Data
Write to
W
Example:
ANDLW
Before Instruction
W
=
After Instruction
W
=
05Fh
A3h
03h
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
ADDWFC
Before Instruction
Carry bit =
REG
=
W
=
After Instruction
Carry bit =
REG
=
W
=
DS39770B-page 302
REG, 0, 1
1
02h
4Dh
0
02h
50h
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
ANDWF
AND W with f
BC
Branch if Carry
Syntax:
ANDWF
Syntax:
BC
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
f {,d {,a}}
Operation:
(W) .AND. (f) → dest
Status Affected:
N, Z
Encoding:
0001
Description:
Operands:
-128 ≤ n ≤ 127
Operation:
if Carry bit is ‘1’,
(PC) + 2 + 2n → PC
Status Affected:
None
Encoding:
01da
ffff
ffff
1110
Description:
The contents of W are ANDed with
register ‘f’. If ‘d’ is ‘0’, the result is stored
in W. If ‘d’ is ‘1’, the result is stored back
in register ‘f’ (default).
Words:
1
Cycles:
1
Q Cycle Activity:
nnnn
nnnn
Words:
1
Cycles:
1(2)
Q Cycle Activity:
If Jump:
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
Write to
PC
No
operation
No
operation
No
operation
No
operation
If No Jump:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
0010
If the Carry bit is ’1’, then the program
will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
n
ANDWF
Before Instruction
W
=
REG
=
After Instruction
W
=
REG
=
REG, 0, 0
Q2
Q3
Q4
Read literal
‘n’
Process
Data
No
operation
Example:
HERE
Before Instruction
PC
After Instruction
If Carry
PC
If Carry
PC
17h
C2h
02h
C2h
© 2007 Microchip Technology Inc.
Q1
Decode
Preliminary
BC
5
=
address (HERE)
=
=
=
=
1;
address (HERE + 12)
0;
address (HERE + 2)
DS39770B-page 303
PIC18F85J90 FAMILY
BCF
Bit Clear f
BN
Branch if Negative
Syntax:
BCF
Syntax:
BN
Operands:
0 ≤ f ≤ 255
0≤b≤7
a ∈ [0,1]
f, b {,a}
Operation:
0 → f<b>
Status Affected:
None
Encoding:
1001
Description:
Operands:
-128 ≤ n ≤ 127
Operation:
if Negative bit is ‘1’,
(PC) + 2 + 2n → PC
Status Affected:
None
Encoding:
bbba
ffff
ffff
1110
Description:
Bit ‘b’ in register ‘f’ is cleared.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q1
Q2
Q3
Q4
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
BCF
Before Instruction
FLAG_REG = C7h
After Instruction
FLAG_REG = 47h
DS39770B-page 304
FLAG_REG,
0110
nnnn
nnnn
If the Negative bit is ‘1’, then the
program will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Words:
1
Cycles:
1(2)
Q Cycle Activity:
If Jump:
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
Write to
PC
No
operation
No
operation
No
operation
No
operation
Q Cycle Activity:
Decode
n
If No Jump:
7, 0
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
No
operation
Example:
HERE
Before Instruction
PC
After Instruction
If Negative
PC
If Negative
PC
Preliminary
BN
Jump
=
address (HERE)
=
=
=
=
1;
address (Jump)
0;
address (HERE + 2)
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
BNC
Branch if Not Carry
BNN
Branch if Not Negative
Syntax:
BNC
Syntax:
BNN
n
n
Operands:
-128 ≤ n ≤ 127
Operands:
-128 ≤ n ≤ 127
Operation:
if Carry bit is ‘0’,
(PC) + 2 + 2n → PC
Operation:
if Negative bit is ‘0’,
(PC) + 2 + 2n → PC
Status Affected:
None
Status Affected:
None
Encoding:
1110
Description:
0011
nnnn
nnnn
If the Carry bit is ‘0’, then the program
will branch.
Encoding:
1110
Description:
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
nnnn
nnnn
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Words:
1
Words:
1
Cycles:
1(2)
Cycles:
1(2)
Q Cycle Activity:
If Jump:
0111
If the Negative bit is ‘0’, then the
program will branch.
Q Cycle Activity:
If Jump:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
Write to
PC
Decode
Read literal
‘n’
Process
Data
Write to
PC
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
No
operation
Decode
Read literal
‘n’
Process
Data
No
operation
If No Jump:
Example:
If No Jump:
HERE
Before Instruction
PC
After Instruction
If Carry
PC
If Carry
PC
BNC
Jump
=
address (HERE)
=
=
=
=
0;
address (Jump)
1;
address (HERE + 2)
© 2007 Microchip Technology Inc.
Example:
HERE
Before Instruction
PC
After Instruction
If Negative
PC
If Negative
PC
Preliminary
BNN
Jump
=
address (HERE)
=
=
=
=
0;
address (Jump)
1;
address (HERE + 2)
DS39770B-page 305
PIC18F85J90 FAMILY
BNOV
Branch if Not Overflow
BNZ
Branch if Not Zero
Syntax:
BNOV
Syntax:
BNZ
n
n
Operands:
-128 ≤ n ≤ 127
Operands:
-128 ≤ n ≤ 127
Operation:
if Overflow bit is ‘0’,
(PC) + 2 + 2n → PC
Operation:
if Zero bit is ‘0’,
(PC) + 2 + 2n → PC
Status Affected:
None
Status Affected:
None
Encoding:
1110
Description:
0101
nnnn
nnnn
If the Overflow bit is ‘0’, then the
program will branch.
Encoding:
1110
Description:
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
nnnn
nnnn
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Words:
1
Words:
1
Cycles:
1(2)
Cycles:
1(2)
Q Cycle Activity:
If Jump:
0001
If the Zero bit is ‘0’, then the program
will branch.
Q Cycle Activity:
If Jump:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
Write to
PC
Decode
Read literal
‘n’
Process
Data
Write to
PC
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
No
operation
Decode
Read literal
‘n’
Process
Data
No
operation
If No Jump:
If No Jump:
Example:
HERE
Before Instruction
PC
After Instruction
If Overflow
PC
If Overflow
PC
DS39770B-page 306
BNOV Jump
=
address (HERE)
=
=
=
=
0;
address (Jump)
1;
address (HERE + 2)
Example:
HERE
Before Instruction
PC
After Instruction
If Zero
PC
If Zero
PC
Preliminary
BNZ
Jump
=
address (HERE)
=
=
=
=
0;
address (Jump)
1;
address (HERE + 2)
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
BRA
Unconditional Branch
BSF
Bit Set f
Syntax:
BRA
Syntax:
BSF
Operands:
0 ≤ f ≤ 255
0≤b≤7
a ∈ [0,1]
Operation:
1 → f<b>
Status Affected:
None
n
Operands:
-1024 ≤ n ≤ 1023
Operation:
(PC) + 2 + 2n → PC
Status Affected:
None
Encoding:
1101
Description:
0nnn
nnnn
nnnn
Add the 2’s complement number ‘2n’ to
the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is a
two-cycle instruction.
Words:
1
Cycles:
2
Encoding:
1000
Description:
Q1
Q2
Q3
Q4
Read literal
‘n’
Process
Data
Write to
PC
No
operation
No
operation
No
operation
No
operation
bbba
ffff
ffff
Bit ‘b’ in register ‘f’ is set.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Q Cycle Activity:
Decode
f, b {,a}
Words:
1
Cycles:
1
Q Cycle Activity:
Example:
HERE
Before Instruction
PC
After Instruction
PC
BRA
Jump
=
address (HERE)
=
address (Jump)
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
BSF
Before Instruction
FLAG_REG
After Instruction
FLAG_REG
© 2007 Microchip Technology Inc.
Preliminary
FLAG_REG, 7, 1
=
0Ah
=
8Ah
DS39770B-page 307
PIC18F85J90 FAMILY
BTFSC
Bit Test File, Skip if Clear
BTFSS
Bit Test File, Skip if Set
Syntax:
BTFSC f, b {,a}
Syntax:
BTFSS f, b {,a}
Operands:
0 ≤ f ≤ 255
0≤b≤7
a ∈ [0,1]
Operands:
0 ≤ f ≤ 255
0≤b<7
a ∈ [0,1]
Operation:
skip if (f<b>) = 0
Operation:
skip if (f<b>) = 1
Status Affected:
None
Status Affected:
None
Encoding:
1011
Description:
bbba
ffff
ffff
If bit ‘b’ in register ‘f’ is ‘0’, then the next
instruction is skipped. If bit ‘b’ is ‘0’, then
the next instruction fetched during the
current instruction execution is discarded
and a NOP is executed instead, making
this a two-cycle instruction.
Encoding:
1010
Description:
bbba
ffff
ffff
If bit ‘b’ in register ‘f’ is ‘1’, then the next
instruction is skipped. If bit ‘b’ is ‘1’, then
the next instruction fetched during the
current instruction execution is discarded
and a NOP is executed instead, making
this a two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected. If
‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’, the Access Bank is selected. If
‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction set
is enabled, this instruction operates in
Indexed Literal Offset Addressing mode
whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates in
Indexed Literal Offset Addressing mode
whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Words:
1
Cycles:
1(2)
Note:
Cycles:
1(2)
Note:
3 cycles if skip and followed
by a 2-word instruction.
Q Cycle Activity:
3 cycles if skip and followed
by a 2-word instruction.
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
No
operation
Decode
Read
register ‘f’
Process
Data
No
operation
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
If skip:
If skip:
If skip and followed by 2-word instruction:
If skip and followed by 2-word instruction:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Example:
HERE
FALSE
TRUE
Before Instruction
PC
After Instruction
If FLAG<1>
PC
If FLAG<1>
PC
DS39770B-page 308
BTFSC
:
:
FLAG, 1, 0
=
address (HERE)
=
=
=
=
0;
address (TRUE)
1;
address (FALSE)
Example:
HERE
FALSE
TRUE
Before Instruction
PC
After Instruction
If FLAG<1>
PC
If FLAG<1>
PC
Preliminary
BTFSS
:
:
FLAG, 1, 0
=
address (HERE)
=
=
=
=
0;
address (FALSE)
1;
address (TRUE)
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
BTG
Bit Toggle f
BOV
Branch if Overflow
Syntax:
BTG f, b {,a}
Syntax:
BOV
Operands:
0 ≤ f ≤ 255
0≤b<7
a ∈ [0,1]
Operands:
-128 ≤ n ≤ 127
Operation:
if Overflow bit is ‘1’,
(PC) + 2 + 2n → PC
Status Affected:
None
Operation:
(f<b>) → f<b>
Status Affected:
None
Encoding:
0111
Description:
Encoding:
bbba
ffff
ffff
1110
Description:
Bit ‘b’ in data memory location ‘f’ is
inverted.
Words:
Words:
1
Cycles:
1(2)
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
BTG
PORTC,
© 2007 Microchip Technology Inc.
nnnn
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
Write to PC
No
operation
No
operation
No
operation
No
operation
If No Jump:
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
No
operation
4, 0
Before Instruction:
PORTC =
0111 0101 [75h]
After Instruction:
PORTC =
0110 0101 [65h]
nnnn
Q Cycle Activity:
If Jump:
1
Cycles:
0100
If the Overflow bit is ‘1’, then the
program will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
n
Example:
HERE
Before Instruction
PC
After Instruction
If Overflow
PC
If Overflow
PC
Preliminary
BOV
Jump
=
address (HERE)
=
=
=
=
1;
address (Jump)
0;
address (HERE + 2)
DS39770B-page 309
PIC18F85J90 FAMILY
BZ
Branch if Zero
CALL
Subroutine Call
Syntax:
BZ
Syntax:
CALL k {,s}
n
Operands:
-128 ≤ n ≤ 127
Operands:
Operation:
if Zero bit is ‘1’,
(PC) + 2 + 2n → PC
0 ≤ k ≤ 1048575
s ∈ [0,1]
Operation:
Status Affected:
None
(PC) + 4 → TOS,
k → PC<20:1>;
if s = 1
(W) → WS,
(STATUS) → STATUSS,
(BSR) → BSRS
Status Affected:
None
Encoding:
1110
Description:
0000
nnnn
nnnn
If the Zero bit is ‘1’, then the program
will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Words:
1
Cycles:
1(2)
Encoding:
1st word (k<7:0>)
2nd word(k<19:8>)
Q1
Q2
Q3
Q4
Read literal
‘n’
Process
Data
Write to
PC
No
operation
No
operation
No
operation
No
operation
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
No
operation
If No Jump:
Example:
HERE
Before Instruction
PC
After Instruction
If Zero
PC
If Zero
PC
DS39770B-page 310
BZ
address (HERE)
=
=
=
=
1;
address (Jump)
0;
address (HERE + 2)
k7kkk
kkkk
kkkk0
kkkk8
Subroutine call of entire 2-Mbyte
memory range. First, return address
(PC+ 4) is pushed onto the return stack.
If ‘s’ = 1, the W, STATUS and BSR
registers are also pushed into their
respective shadow registers, WS,
STATUSS and BSRS. If ‘s’ = 0, no
update occurs (default). Then, the
20-bit value ‘k’ is loaded into PC<20:1>.
CALL is a two-cycle instruction.
Words:
2
Cycles:
2
Q Cycle Activity:
Jump
=
110s
k19kkk
Description:
Q Cycle Activity:
If Jump:
Decode
1110
1111
Q1
Q2
Q3
Q4
Decode
Read literal
‘k’<7:0>,
Push PC to
stack
Read literal
’k’<19:8>,
Write to PC
No
operation
No
operation
No
operation
No
operation
Example:
HERE
Before Instruction
PC
=
After Instruction
PC
=
TOS
=
WS
=
BSRS
=
STATUSS =
Preliminary
CALL
THERE,1
address (HERE)
address (THERE)
address (HERE + 4)
W
BSR
STATUS
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
CLRF
Clear f
Syntax:
CLRF
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
f {,a}
Operation:
000h → f,
1→Z
Status Affected:
Z
Encoding:
0110
Description:
101a
ffff
ffff
Clears the contents of the specified
register.
CLRWDT
Clear Watchdog Timer
Syntax:
CLRWDT
Operands:
None
Operation:
000h → WDT,
000h → WDT postscaler,
1 → TO,
1 → PD
Status Affected:
TO, PD
Encoding:
0000
Words:
1
Cycles:
1
1
Cycles:
1
Q Cycle Activity:
Q Cycle Activity:
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
CLRF
Before Instruction
FLAG_REG
After Instruction
FLAG_REG
FLAG_REG,1
=
5Ah
=
00h
© 2007 Microchip Technology Inc.
0100
Words:
Q1
Q2
Q3
Q4
Decode
No
operation
Process
Data
No
operation
Example:
Q1
0000
CLRWDT instruction resets the
Watchdog Timer. It also resets the
postscaler of the WDT. Status bits, TO
and PD, are set.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
0000
Description:
Preliminary
CLRWDT
Before Instruction
WDT Counter
After Instruction
WDT Counter
WDT Postscaler
TO
PD
=
?
=
=
=
=
00h
0
1
1
DS39770B-page 311
PIC18F85J90 FAMILY
COMF
Complement f
CPFSEQ
Compare f with W, Skip if f = W
Syntax:
COMF
Syntax:
CPFSEQ
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
Operation:
(f) – (W),
skip if (f) = (W)
(unsigned comparison)
Status Affected:
None
f {,d {,a}}
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
f → dest
Status Affected:
N, Z
Encoding:
0001
Description:
11da
ffff
ffff
The contents of register ‘f’ are
complemented. If ‘d’ is ‘0’, the result is
stored in W. If ‘d’ is ‘1’, the result is
stored back in register ‘f’ (default).
Encoding:
Description:
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
1
Cycles:
1
Decode
Q2
Read
register ‘f’
Example:
COMF
Before Instruction
REG
=
After Instruction
REG
=
W
=
13h
13h
ECh
Q3
Process
Data
REG, 0, 0
ffff
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Q4
Words:
1
Write to
destination
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
Q Cycle Activity:
Q1
Decode
Q2
Read
register ‘f’
Q3
Process
Data
Q4
No
operation
If skip:
Q1
Q2
Q3
No
No
No
operation
operation
operation
If skip and followed by 2-word instruction:
Q1
Q2
Q3
No
No
No
operation
operation
operation
No
No
No
operation
operation
operation
Example:
HERE
NEQUAL
EQUAL
Before Instruction
PC Address
W
REG
After Instruction
If REG
PC
If REG
PC
DS39770B-page 312
ffff
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
Q Cycle Activity:
Q1
001a
Compares the contents of data memory
location ‘f’ to the contents of W by
performing an unsigned subtraction.
If ‘f’ = W, then the fetched instruction is
discarded and a NOP is executed
instead, making this a two-cycle
instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
Words:
0110
f {,a}
Preliminary
Q4
No
operation
Q4
No
operation
No
operation
CPFSEQ REG, 0
:
:
=
=
=
HERE
?
?
=
=
≠
=
W;
Address (EQUAL)
W;
Address (NEQUAL)
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
CPFSGT
Compare f with W, Skip if f > W
CPFSLT
Compare f with W, Skip if f < W
Syntax:
CPFSGT
Syntax:
CPFSLT
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
Operands:
Operation:
(f) – (W),
skip if (f) > (W)
(unsigned comparison)
0 ≤ f ≤ 255
a ∈ [0,1]
Operation:
(f) – (W),
skip if (f) < (W)
(unsigned comparison)
Status Affected:
None
Status Affected:
None
Encoding:
Description:
0110
f {,a}
010a
ffff
ffff
Compares the contents of data memory
location ‘f’ to the contents of the W by
performing an unsigned subtraction.
Encoding:
0110
Description:
If the contents of ‘f’ are greater than the
contents of WREG, then the fetched
instruction is discarded and a NOP is
executed instead, making this a
two-cycle instruction.
Words:
1
Cycles:
1(2)
Note:
Q Cycle Activity:
Q1
Decode
3 cycles if skip and followed
by a 2-word instruction.
Q2
Read
register ‘f’
Q3
Process
Data
Q4
No
operation
Example:
HERE
NGREATER
GREATER
Before Instruction
PC
W
After Instruction
If REG
PC
If REG
PC
Address (HERE)
?
>
=
≤
=
W;
Address (GREATER)
W;
Address (NGREATER)
© 2007 Microchip Technology Inc.
Compares the contents of data memory
location ‘f’ to the contents of W by
performing an unsigned subtraction.
1
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
No
operation
If skip:
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
If skip and followed by 2-word instruction:
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Example:
CPFSGT REG, 0
:
:
=
=
ffff
Words:
Q4
No
operation
Q4
No
operation
No
operation
ffff
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If skip:
Q1
Q2
Q3
No
No
No
operation
operation
operation
If skip and followed by 2-word instruction:
Q1
Q2
Q3
No
No
No
operation
operation
operation
No
No
No
operation
operation
operation
000a
If the contents of ‘f’ are less than the
contents of W, then the fetched
instruction is discarded and a NOP is
executed instead, making this a
two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
f {,a}
Preliminary
HERE
NLESS
LESS
Before Instruction
PC
W
After Instruction
If REG
PC
If REG
PC
CPFSLT REG, 1
:
:
=
=
Address (HERE)
?
<
=
≥
=
W;
Address (LESS)
W;
Address (NLESS)
DS39770B-page 313
PIC18F85J90 FAMILY
DAW
Decimal Adjust W Register
DECF
Decrement f
Syntax:
DAW
Syntax:
DECF f {,d {,a}}
Operands:
None
Operands:
Operation:
If [W<3:0> > 9] or [DC = 1], then
(W<3:0>) + 6 → W<3:0>;
else
(W<3:0>) → W<3:0>
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f) – 1 → dest
Status Affected:
C, DC, N, OV, Z
Encoding:
If [W<7:4> > 9] or [C = 1], then
(W<7:4>) + 6 → W<7:4>;
C = 1;
else
(W<7:4>) → W<7:4>
Status Affected:
0000
Description:
C
Encoding:
0000
Description:
0000
0000
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register W
Process
Data
Write
W
Example 1:
A5h
0
0
DS39770B-page 314
Decrement register ‘f’. If ‘d’ is ‘0’, the
result is stored in W. If ‘d’ is ‘1’, the
result is stored back in register ‘f’
(default).
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
DECF
Before Instruction
CNT
=
Z
=
After Instruction
CNT
=
Z
=
05h
1
0
Example 2:
Before Instruction
W
=
C
=
DC
=
After Instruction
W
=
C
=
DC
=
ffff
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
DAW
Before Instruction
W
=
C
=
DC
=
After Instruction
W
=
C
=
DC
=
ffff
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
0111
DAW adjusts the eight-bit value in W,
resulting from the earlier addition of two
variables (each in packed BCD format)
and produces a correct packed BCD
result.
Words:
01da
CNT,
1, 0
01h
0
00h
1
CEh
0
0
34h
1
0
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
DECFSZ
Decrement f, Skip if 0
DCFSNZ
Decrement f, Skip if Not 0
Syntax:
DECFSZ f {,d {,a}}
Syntax:
DCFSNZ
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f) – 1 → dest,
skip if result = 0
Operation:
(f) – 1 → dest,
skip if result ≠ 0
Status Affected:
None
Status Affected:
None
Encoding:
0010
Description:
11da
ffff
ffff
The contents of register ‘f’ are
decremented. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
Encoding:
0100
Description:
If the result is ‘0’, the next instruction
which is already fetched is discarded
and a NOP is executed instead, making
it a two-cycle instruction.
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
Words:
1
Cycles:
1(2)
Note:
Q2
Q3
Q4
Read
register ‘f’
Process
Data
Write to
destination
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
If skip:
If skip:
If skip and followed by 2-word instruction:
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
DECFSZ
GOTO
CNT, 1, 1
LOOP
Q2
Q3
Q4
No
operation
No
operation
No
operation
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Example:
CONTINUE
HERE
ZERO
NZERO
Before Instruction
TEMP
After Instruction
TEMP
If TEMP
PC
If TEMP
PC
Address (HERE)
CNT – 1
0;
Address (CONTINUE)
0;
Address (HERE + 2)
© 2007 Microchip Technology Inc.
Q1
No
operation
If skip and followed by 2-word instruction:
Q1
No
operation
Before Instruction
PC
=
After Instruction
CNT
=
If CNT
=
PC =
If CNT
≠
PC =
3 cycles if skip and followed
by a 2-word instruction.
Q Cycle Activity:
Q1
Decode
HERE
ffff
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Q Cycle Activity:
Example:
ffff
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
1
11da
The contents of register ‘f’ are
decremented. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
If the result is not ‘0’, the next
instruction which is already fetched is
discarded and a NOP is executed
instead, making it a two-cycle
instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
Words:
f {,d {,a}}
Preliminary
DCFSNZ
:
:
TEMP, 1, 0
=
?
=
=
=
≠
=
TEMP – 1,
0;
Address (ZERO)
0;
Address (NZERO)
DS39770B-page 315
PIC18F85J90 FAMILY
GOTO
Unconditional Branch
INCF
Increment f
Syntax:
GOTO k
Syntax:
INCF
Operands:
0 ≤ k ≤ 1048575
Operands:
Operation:
k → PC<20:1>
Status Affected:
None
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f) + 1 → dest
Status Affected:
C, DC, N, OV, Z
Encoding:
1st word (k<7:0>)
2nd word(k<19:8>)
1110
1111
1111
k19kkk
k7kkk
kkkk
kkkk0
kkkk8
Description:
GOTO allows an unconditional branch
anywhere within entire 2-Mbyte memory
range. The 20-bit value ‘k’ is loaded into
PC<20:1>. GOTO is always a two-cycle
instruction.
Words:
2
Cycles:
2
Encoding:
0010
Description:
Q1
Q2
Q3
Q4
Read literal
‘k’<7:0>,
No
operation
Read literal
‘k’<19:8>,
Write to PC
No
operation
No
operation
No
operation
No
operation
Example:
ffff
ffff
The contents of register ‘f’ are
incremented. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
GOTO THERE
After Instruction
PC =
Address (THERE)
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
INCF
Before Instruction
CNT
=
Z
=
C
=
DC
=
After Instruction
CNT
=
Z
=
C
=
DC
=
DS39770B-page 316
10da
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
Q Cycle Activity:
Decode
f {,d {,a}}
Preliminary
CNT, 1, 0
FFh
0
?
?
00h
1
1
1
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
INCFSZ
Increment f, Skip if 0
INFSNZ
Syntax:
INCFSZ
Syntax:
INFSNZ
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
f {,d {,a}}
Increment f, Skip if Not 0
f {,d {,a}}
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
Operation:
(f) + 1 → dest,
skip if result = 0
Operation:
(f) + 1 → dest,
skip if result ≠ 0
Status Affected:
None
Status Affected:
None
Encoding:
0011
Description:
11da
ffff
ffff
The contents of register ‘f’ are
incremented. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’. (default)
Encoding:
0100
Description:
10da
ffff
ffff
The contents of register ‘f’ are
incremented. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
If the result is ‘0’, the next instruction
which is already fetched is discarded
and a NOP is executed instead, making
it a two-cycle instruction.
If the result is not ‘0’, the next
instruction which is already fetched is
discarded and a NOP is executed
instead, making it a two-cycle
instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Words:
1
Cycles:
1(2)
Note:
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
3 cycles if skip and followed
by a 2-word instruction.
Q Cycle Activity:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Decode
Read
register ‘f’
Process
Data
Write to
destination
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
If skip:
If skip:
If skip and followed by 2-word instruction:
If skip and followed by 2-word instruction:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Example:
HERE
NZERO
ZERO
Before Instruction
PC
=
After Instruction
CNT
=
If CNT
=
PC
=
If CNT
≠
PC
=
INCFSZ
:
:
CNT, 1, 0
Example:
Before Instruction
PC
=
After Instruction
REG
=
If REG
≠
PC
=
If REG
=
PC
=
Address (HERE)
CNT + 1
0;
Address (ZERO)
0;
Address (NZERO)
© 2007 Microchip Technology Inc.
HERE
ZERO
NZERO
Preliminary
INFSNZ
REG, 1, 0
Address (HERE)
REG + 1
0;
Address (NZERO)
0;
Address (ZERO)
DS39770B-page 317
PIC18F85J90 FAMILY
IORLW
Inclusive OR Literal with W
IORWF
Inclusive OR W with f
Syntax:
IORLW k
Syntax:
IORWF
Operands:
0 ≤ k ≤ 255
Operands:
Operation:
(W) .OR. k → W
Status Affected:
N, Z
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(W) .OR. (f) → dest
Status Affected:
N, Z
Encoding:
0000
1001
kkkk
kkkk
Description:
The contents of W are ORed with the
eight-bit literal ‘k’. The result is placed
in W.
Words:
1
Cycles:
1
Encoding:
0001
Description:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write to
W
Example:
IORLW
Before Instruction
W
=
After Instruction
W
=
00da
ffff
ffff
Inclusive OR W with register ‘f’. If ‘d’ is
‘0’, the result is placed in W. If ‘d’ is ‘1’,
the result is placed back in register ‘f’
(default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
35h
9Ah
BFh
f {,d {,a}}
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
IORWF
Before Instruction
RESULT =
W
=
After Instruction
RESULT =
W
=
DS39770B-page 318
Preliminary
RESULT, 0, 1
13h
91h
13h
93h
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
LFSR
Load FSR
MOVF
Move f
Syntax:
LFSR f, k
Syntax:
MOVF
Operands:
0≤f≤2
0 ≤ k ≤ 4095
Operands:
Operation:
k → FSRf
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Status Affected:
None
Operation:
f → dest
Status Affected:
N, Z
Encoding:
1110
1111
1110
0000
00ff
k7kkk
k11kkk
kkkk
Description:
The 12-bit literal ‘k’ is loaded into the
file select register pointed to by ‘f’.
Words:
2
Cycles:
2
Encoding:
0101
Description:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read literal
‘k’ MSB
Process
Data
Write
literal ‘k’
MSB to
FSRfH
Decode
Read literal
‘k’ LSB
Process
Data
Write literal
‘k’ to FSRfL
Example:
After Instruction
FSR2H
FSR2L
03h
ABh
00da
ffff
ffff
The contents of register ‘f’ are moved to
a destination dependent upon the
status of ‘d’. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
Location ‘f’ can be anywhere in the
256-byte bank.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
LFSR 2, 3ABh
=
=
f {,d {,a}}
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
W
Example:
MOVF
Before Instruction
REG
W
After Instruction
REG
W
© 2007 Microchip Technology Inc.
Preliminary
REG, 0, 0
=
=
22h
FFh
=
=
22h
22h
DS39770B-page 319
PIC18F85J90 FAMILY
MOVFF
Move f to f
MOVLB
Move Literal to Low Nibble in BSR
Syntax:
MOVFF fs,fd
Syntax:
MOVLW k
Operands:
0 ≤ fs ≤ 4095
0 ≤ fd ≤ 4095
Operands:
0 ≤ k ≤ 255
Operation:
k → BSR
Status Affected:
None
Operation:
(fs) → fd
Status Affected:
None
Encoding:
1st word (source)
2nd word (destin.)
Encoding:
1100
1111
Description:
ffff
ffff
ffff
ffff
ffffs
ffffd
The contents of source register ‘fs’ are
moved to destination register ‘fd’.
Location of source ‘fs’ can be anywhere
in the 4096-byte data space (000h to
FFFh) and location of destination ‘fd’
can also be anywhere from 000h to
FFFh.
2
Cycles:
2
kkkk
kkkk
The eight-bit literal ‘k’ is loaded into the
Bank Select Register (BSR). The value
of BSR<7:4> always remains ‘0’
regardless of the value of k7:k4.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write literal
‘k’ to BSR
MOVLB
5
Example:
The MOVFF instruction cannot use the
PCL, TOSU, TOSH or TOSL as the
destination register
Words:
0001
Description:
Either source or destination can be W
(a useful special situation).
MOVFF is particularly useful for
transferring a data memory location to a
peripheral register (such as the transmit
buffer or an I/O port).
0000
Before Instruction
BSR Register =
After Instruction
BSR Register =
02h
05h
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
(src)
Process
Data
No
operation
Decode
No
operation
No
operation
Write
register ‘f’
(dest)
No dummy
read
Example:
MOVFF
Before Instruction
REG1
REG2
After Instruction
REG1
REG2
DS39770B-page 320
REG1, REG2
=
=
33h
11h
=
=
33h
33h
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
MOVLW
Move Literal to W
MOVWF
Move W to f
Syntax:
MOVLW k
Syntax:
MOVWF
Operands:
0 ≤ k ≤ 255
Operands:
Operation:
k→W
0 ≤ f ≤ 255
a ∈ [0,1]
Status Affected:
None
Encoding:
0000
Description:
1110
kkkk
kkkk
The eight-bit literal ‘k’ is loaded into W.
Words:
1
Cycles:
1
Operation:
(W) → f
Status Affected:
None
Encoding:
0110
Description:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write to
W
Example:
After Instruction
W
=
MOVLW
f {,a}
111a
ffff
ffff
Move data from W to register ‘f’.
Location ‘f’ can be anywhere in the
256-byte bank.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
5Ah
5Ah
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
MOVWF
Before Instruction
W
=
REG
=
After Instruction
W
=
REG
=
© 2007 Microchip Technology Inc.
Preliminary
REG, 0
4Fh
FFh
4Fh
4Fh
DS39770B-page 321
PIC18F85J90 FAMILY
MULLW
Multiply Literal with W
MULWF
Syntax:
MULLW
Syntax:
MULWF
Operands:
0 ≤ k ≤ 255
Operands:
Operation:
(W) x k → PRODH:PRODL
0 ≤ f ≤ 255
a ∈ [0,1]
Status Affected:
None
Operation:
(W) x (f) → PRODH:PRODL
Status Affected:
None
Encoding:
0000
Description:
k
1101
kkkk
kkkk
An unsigned multiplication is carried
out between the contents of W and the
8-bit literal ‘k’. The 16-bit result is
placed in the PRODH:PRODL register
pair. PRODH contains the high byte.
Multiply W with f
Encoding:
0000
Description:
W is unchanged.
None of the Status flags are affected.
1
Cycles:
1
Q1
Q2
Q3
Q4
Read
literal ‘k’
Process
Data
Write
registers
PRODH:
PRODL
MULLW
If ‘a’ is ‘0’ and the extended instruction set
is enabled, this instruction operates in
Indexed Literal Offset Addressing mode
whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
0C4h
=
=
=
E2h
?
?
=
=
=
E2h
ADh
08h
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
registers
PRODH:
PRODL
Example:
Before Instruction
W
REG
PRODH
PRODL
After Instruction
W
REG
PRODH
PRODL
DS39770B-page 322
ffff
If ‘a’ is ‘0’, the Access Bank is selected. If
‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
Decode
Before Instruction
W
PRODH
PRODL
After Instruction
W
PRODH
PRODL
ffff
Note that neither Overflow nor Carry is
possible in this operation. A Zero result is
possible but not detected.
Q Cycle Activity:
Example:
001a
An unsigned multiplication is carried out
between the contents of W and the
register file location ‘f’. The 16-bit result is
stored in the PRODH:PRODL register
pair. PRODH contains the high byte. Both
W and ‘f’ are unchanged.
None of the Status flags are affected.
Note that neither Overflow nor Carry is
possible in this operation. A Zero result
is possible but not detected.
Words:
f {,a}
Preliminary
MULWF
REG, 1
=
=
=
=
C4h
B5h
?
?
=
=
=
=
C4h
B5h
8Ah
94h
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
NEGF
Negate f
Syntax:
NEGF
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
f {,a}
Operation:
(f) + 1 → f
Status Affected:
N, OV, C, DC, Z
Encoding:
0110
Description:
110a
ffff
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
1
1
Syntax:
NOP
Operands:
None
Operation:
No operation
Status Affected:
None
0000
1111
ffff
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
Cycles:
No Operation
Encoding:
Location ‘f’ is negated using two’s
complement. The result is placed in the
data memory location ‘f’.
Words:
NOP
0000
xxxx
Description:
No operation.
Words:
1
Cycles:
1
0000
xxxx
0000
xxxx
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
No
operation
No
operation
No
operation
Example:
None.
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
NEGF
Before Instruction
REG
=
After Instruction
REG
=
REG, 1
0011 1010 [3Ah]
1100 0110 [C6h]
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 323
PIC18F85J90 FAMILY
POP
Pop Top of Return Stack
PUSH
Push Top of Return Stack
Syntax:
POP
Syntax:
PUSH
Operands:
None
Operands:
None
Operation:
(TOS) → bit bucket
Operation:
(PC + 2) → TOS
Status Affected:
None
Status Affected:
None
Encoding:
0000
0000
0000
0110
Description:
The TOS value is pulled off the return
stack and is discarded. The TOS value
then becomes the previous value that
was pushed onto the return stack.
This instruction is provided to enable
the user to properly manage the return
stack to incorporate a software stack.
Words:
1
Cycles:
1
Encoding:
Q2
Q3
Q4
Decode
No
operation
POP TOS
value
No
operation
POP
GOTO
NEW
Before Instruction
TOS
Stack (1 level down)
DS39770B-page 324
0000
0101
The PC + 2 is pushed onto the top of
the return stack. The previous TOS
value is pushed down on the stack.
This instruction allows implementing a
software stack by modifying TOS and
then pushing it onto the return stack.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
After Instruction
TOS
PC
0000
Description:
Q Cycle Activity:
Example:
0000
Q1
Q2
Q3
Q4
Decode
PUSH
PC + 2 onto
return stack
No
operation
No
operation
Example:
=
=
=
=
0031A2h
014332h
014332h
NEW
Preliminary
PUSH
Before Instruction
TOS
PC
=
=
345Ah
0124h
After Instruction
PC
TOS
Stack (1 level down)
=
=
=
0126h
0126h
345Ah
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
RCALL
Relative Call
RESET
Reset
Syntax:
RCALL
Syntax:
RESET
n
Operands:
-1024 ≤ n ≤ 1023
Operands:
None
Operation:
(PC) + 2 → TOS,
(PC) + 2 + 2n → PC
Operation:
Reset all registers and flags that are
affected by a MCLR Reset.
Status Affected:
None
Status Affected:
All
Encoding:
1101
Description:
1nnn
nnnn
nnnn
Subroutine call with a jump up to 1K
from the current location. First, return
address (PC + 2) is pushed onto the
stack. Then, add the 2’s complement
number ‘2n’ to the PC. Since the PC will
have incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is a
two-cycle instruction.
Words:
1
Cycles:
2
Encoding:
0000
Q2
Q3
Q4
Read literal
‘n’
Process
Data
Write to PC
No
operation
No
operation
1111
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Start
reset
No
operation
No
operation
Example:
Q1
1111
This instruction provides a way to
execute a MCLR Reset in software.
Q Cycle Activity:
Decode
0000
Description:
After Instruction
Registers =
Flags*
=
RESET
Reset Value
Reset Value
PUSH PC
to stack
No
operation
Example:
No
operation
HERE
RCALL Jump
Before Instruction
PC =
Address (HERE)
After Instruction
PC =
Address (Jump)
TOS =
Address (HERE + 2)
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 325
PIC18F85J90 FAMILY
RETFIE
Return from Interrupt
RETLW
Return Literal to W
Syntax:
RETFIE {s}
Syntax:
RETLW k
Operands:
s ∈ [0,1]
Operands:
0 ≤ k ≤ 255
Operation:
(TOS) → PC,
1 → GIE/GIEH or PEIE/GIEL;
if s = 1
(WS) → W,
(STATUSS) → STATUS,
(BSRS) → BSR,
PCLATU, PCLATH are unchanged
Operation:
k → W,
(TOS) → PC,
PCLATU, PCLATH are unchanged
Status Affected:
None
Status Affected:
Encoding:
0000
Description:
0000
0001
Words:
1
Cycles:
2
Q Cycle Activity:
kkkk
kkkk
W is loaded with the eight-bit literal ‘k’.
The program counter is loaded from the
top of the stack (the return address).
The high address latch (PCLATH)
remains unchanged.
Words:
1
Cycles:
2
000s
Return from interrupt. Stack is popped
and Top-of-Stack (TOS) is loaded into
the PC. Interrupts are enabled by
setting either the high or low priority
global interrupt enable bit. If ‘s’ = 1, the
contents of the shadow registers WS,
STATUSS and BSRS are loaded into
their corresponding registers W,
STATUS and BSR. If ‘s’ = 0, no update
of these registers occurs (default).
1100
Description:
GIE/GIEH, PEIE/GIEL.
Encoding:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
POP PC
from stack,
write to W
No
operation
No
operation
No
operation
No
operation
Example:
Q1
Q2
Q3
Q4
Decode
No
operation
No
operation
POP PC
from stack
Set GIEH or
GIEL
No
operation
0000
No
operation
Example:
RETFIE
After Interrupt
PC
W
BSR
STATUS
GIE/GIEH, PEIE/GIEL
DS39770B-page 326
No
operation
No
operation
1
=
=
=
=
=
TOS
WS
BSRS
STATUSS
1
CALL TABLE ;
;
;
;
:
TABLE
ADDWF PCL ;
RETLW k0
;
RETLW k1
;
:
:
RETLW kn
;
Before Instruction
W
=
After Instruction
W
=
Preliminary
W contains table
offset value
W now has
table value
W = offset
Begin table
End of table
07h
value of kn
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
RETURN
Return from Subroutine
RLCF
Rotate Left f through Carry
Syntax:
RETURN {s}
Syntax:
RLCF
Operands:
s ∈ [0,1]
Operands:
Operation:
(TOS) → PC;
if s = 1
(WS) → W,
(STATUSS) → STATUS,
(BSRS) → BSR,
PCLATU, PCLATH are unchanged
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f<n>) → dest<n + 1>,
(f<7>) → C,
(C) → dest<0>
Status Affected:
C, N, Z
Status Affected:
None
Encoding:
0000
Description:
Encoding:
0000
0001
001s
0011
Description:
Return from subroutine. The stack is
popped and the top of the stack (TOS)
is loaded into the program counter. If
‘s’= 1, the contents of the shadow
registers WS, STATUSS and BSRS are
loaded into their corresponding
registers W, STATUS and BSR. If
‘s’ = 0, no update of these registers
occurs (default).
Words:
1
Cycles:
2
Q1
Q2
Q3
Q4
No
operation
Process
Data
POP PC
from stack
No
operation
No
operation
No
operation
No
operation
01da
ffff
ffff
The contents of register ‘f’ are rotated
one bit to the left through the Carry flag.
If ‘d’ is ‘0’, the result is placed in W. If ‘d’
is ‘1’, the result is stored back in register
‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Q Cycle Activity:
Decode
f {,d {,a}}
register f
C
Words:
1
Cycles:
1
Q Cycle Activity:
Example:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
RETURN
After Instruction:
PC = TOS
Example:
Before Instruction
REG
=
C
=
After Instruction
REG
=
W
=
C
=
© 2007 Microchip Technology Inc.
Preliminary
RLCF
REG, 0, 0
1110 0110
0
1110 0110
1100 1100
1
DS39770B-page 327
PIC18F85J90 FAMILY
RLNCF
Rotate Left f (No Carry)
RRCF
Rotate Right f through Carry
Syntax:
RLNCF
Syntax:
RRCF
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f<n>) → dest<n + 1>,
(f<7>) → dest<0>
Operation:
Status Affected:
N, Z
(f<n>) → dest<n – 1>,
(f<0>) → C,
(C) → dest<7>
Status Affected:
C, N, Z
Encoding:
0100
Description:
f {,d {,a}}
01da
ffff
ffff
The contents of register ‘f’ are rotated
one bit to the left. If ‘d’ is ‘0’, the result
is placed in W. If ‘d’ is ‘1’, the result is
stored back in register ‘f’ (default).
Encoding:
0011
Description:
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
1
1
Q1
Decode
Q2
Read
register ‘f’
Example:
Before Instruction
REG
=
After Instruction
REG
=
DS39770B-page 328
RLNCF
Q3
Process
Data
Q4
Write to
destination
Words:
1
Cycles:
register f
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
REG, 1, 0
1010 1011
ffff
The contents of register ‘f’ are rotated
one bit to the right through the Carry
flag. If ‘d’ is ‘0’, the result is placed in W.
If ‘d’ is ‘1’, the result is placed back in
register ‘f’ (default).
C
Q Cycle Activity:
ffff
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
register f
Cycles:
00da
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
f {,d {,a}}
Example:
RRCF
Before Instruction
REG
=
C
=
After Instruction
REG
=
W
=
C
=
0101 0111
Preliminary
REG, 0, 0
1110 0110
0
1110 0110
0111 0011
0
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
RRNCF
Rotate Right f (No Carry)
SETF
Set f
Syntax:
RRNCF
Syntax:
SETF
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
Operation:
(f<n>) → dest<n – 1>,
(f<0>) → dest<7>
Status Affected:
N, Z
Encoding:
0100
Description:
f {,d {,a}}
00da
Operation:
FFh → f
Status Affected:
None
Encoding:
ffff
ffff
0110
Description:
The contents of register ‘f’ are rotated
one bit to the right. If ‘d’ is ‘0’, the result
is placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
1
Cycles:
1
Words:
1
Cycles:
1
Q Cycle Activity:
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example 1:
RRNCF
Before Instruction
REG
=
After Instruction
REG
=
Example 2:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
SETF
Before Instruction
REG
After Instruction
REG
REG,1
=
5Ah
=
FFh
REG, 1, 0
1101 0111
1110 1011
RRNCF
Before Instruction
W
=
REG
=
After Instruction
W
=
REG
=
ffff
Q Cycle Activity:
Example:
Q1
ffff
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
register f
Words:
100a
The contents of the specified register
are set to FFh.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’, the Access Bank will be
selected, overriding the BSR value. If ‘a’
is ‘1’, then the bank will be selected as
per the BSR value (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
f {,a}
REG, 0, 0
?
1101 0111
1110 1011
1101 0111
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 329
PIC18F85J90 FAMILY
SLEEP
Enter Sleep Mode
SUBFWB
Subtract f from W with Borrow
Syntax:
SLEEP
Syntax:
SUBFWB
Operands:
None
Operands:
Operation:
00h → WDT,
0 → WDT postscaler,
1 → TO,
0 → PD
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(W) – (f) – (C) → dest
Status Affected:
N, OV, C, DC, Z
Status Affected:
TO, PD
Encoding:
0000
Description:
Encoding:
0000
0000
0011
0101
Description:
The Power-Down status bit (PD) is
cleared. The Time-out status bit (TO)
is set. The Watchdog Timer and its
postscaler are cleared.
The processor is put into Sleep mode
with the oscillator stopped.
Words:
1
Cycles:
1
Q1
Q2
Q3
Q4
No
operation
Process
Data
Go to
Sleep
Example:
SLEEP
Before Instruction
TO =
?
?
PD =
DS39770B-page 330
ffff
ffff
Subtract register ‘f’ and Carry flag
(borrow) from W (2’s complement
method). If ‘d’ is ‘0’, the result is stored in
W. If ‘d’ is ‘1’, the result is stored in
register ‘f’ (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates in
Indexed Literal Offset Addressing mode
whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q Cycle Activity:
After Instruction
1†
TO =
PD =
0
† If WDT causes wake-up, this bit is cleared.
01da
If ‘a’ is ‘0’, the Access Bank is selected. If
‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
Q Cycle Activity:
Decode
f {,d {,a}}
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
SUBFWB
REG, 1, 0
Example 1:
Before Instruction
REG
=
3
W
=
2
C
=
1
After Instruction
REG
=
FF
W
=
2
C
=
0
Z
=
0
N
=
1
; result is negative
SUBFWB
REG, 0, 0
Example 2:
Before Instruction
REG
=
2
W
=
5
C
=
1
After Instruction
REG
=
2
W
=
3
C
=
1
Z
=
0
N
=
0
; result is positive
SUBFWB
REG, 1, 0
Example 3:
Before Instruction
REG
=
1
W
=
2
C
=
0
After Instruction
REG
=
0
W
=
2
C
=
1
Z
=
1
; result is zero
N
=
0
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
SUBLW
Subtract W from Literal
SUBWF
Subtract W from f
Syntax:
SUBLW k
Syntax:
SUBWF
Operands:
0 ≤ k ≤ 255
Operands:
Operation:
k – (W) → W
Status Affected:
N, OV, C, DC, Z
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f) – (W) → dest
Status Affected:
N, OV, C, DC, Z
Encoding:
0000
1000
kkkk
kkkk
Description:
W is subtracted from the eight-bit
literal ‘k’. The result is placed in W.
Words:
1
Cycles:
1
Encoding:
0101
Description:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write to
W
Example 1:
Before Instruction
W
=
C
=
After Instruction
W
=
C
=
Z
=
N
=
Example 2:
Before Instruction
W
=
C
=
After Instruction
W
=
C
=
Z
=
N
=
Example 3:
Before Instruction
W
=
C
=
After Instruction
W
=
C
=
Z
=
N
=
SUBLW
SUBLW
11da
ffff
ffff
Subtract W from register ‘f’ (2’s
complement method). If ‘d’ is ‘0’, the
result is stored in W. If ‘d’ is ‘1’, the result
is stored back in register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
02h
01h
?
01h
1
0
0
f {,d {,a}}
; result is positive
Words:
1
Cycles:
1
02h
Q Cycle Activity:
02h
?
00h
1
1
0
SUBLW
; result is zero
Q2
Q3
Q4
Read
register ‘f’
Process
Data
Write to
destination
SUBWF
REG, 1, 0
Example 1:
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
=
C
=
Z
=
N
=
02h
03h
?
FFh
0
0
1
Q1
Decode
; (2’s complement)
; result is negative
Example 2:
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
=
C
=
Z
=
N
=
Example 3:
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
=
C
=
Z
=
N
=
© 2007 Microchip Technology Inc.
Preliminary
3
2
?
1
2
1
0
0
; result is positive
SUBWF
REG, 0, 0
2
2
?
2
0
1
1
0
SUBWF
; result is zero
REG, 1, 0
1
2
?
FFh ;(2’s complement)
2
0
; result is negative
0
1
DS39770B-page 331
PIC18F85J90 FAMILY
SUBWFB
Subtract W from f with Borrow
SWAPF
Swap f
Syntax:
SUBWFB
Syntax:
SWAPF f {,d {,a}}
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
Operation:
(f) – (W) – (C) → dest
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
Status Affected:
N, OV, C, DC, Z
(f<3:0>) → dest<7:4>,
(f<7:4>) → dest<3:0>
Status Affected:
None
Encoding:
0101
Description:
f {,d {,a}}
10da
ffff
ffff
Subtract W and the Carry flag (borrow)
from register ‘f’ (2’s complement
method). If ‘d’ is ‘0’, the result is stored
in W. If ‘d’ is ‘1’, the result is stored back
in register ‘f’ (default).
Encoding:
0011
Description:
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
1
Cycles:
1
Q Cycle Activity:
Q1
Decode
Q2
Read
register ‘f’
Example 1:
SUBWFB
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
=
C
=
Z
=
N
=
Example 2:
Q4
Write to
destination
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
REG, 1, 0
19h
0Dh
1
(0001 1001)
(0000 1101)
0Ch
0Dh
1
0
0
(0000 1011)
(0000 1101)
ffff
Example:
SWAPF
Before Instruction
REG
=
After Instruction
REG
=
REG, 1, 0
53h
35h
; result is positive
SUBWFB REG, 0, 0
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
=
C
=
Z
=
N
=
Example 3:
1Bh
1Ah
0
(0001 1011)
(0001 1010)
1Bh
00h
1
1
0
(0001 1011)
SUBWFB
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
C
Z
N
Q3
Process
Data
ffff
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
10da
The upper and lower nibbles of register
‘f’ are exchanged. If ‘d’ is ‘0’, the result
is placed in W. If ‘d’ is ‘1’, the result is
placed in register ‘f’ (default).
=
=
=
=
DS39770B-page 332
; result is zero
REG, 1, 0
03h
0Eh
1
(0000 0011)
(0000 1101)
F5h
(1111 0100)
; [2’s comp]
(0000 1101)
0Eh
0
0
1
; result is negative
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TBLRD
Table Read
TBLRD
Table Read (Continued)
Syntax:
TBLRD ( *; *+; *-; +*)
Example 1:
TBLRD
Operands:
None
Operation:
if TBLRD *,
(Prog Mem (TBLPTR)) → TABLAT;
TBLPTR – No Change
if TBLRD *+,
(Prog Mem (TBLPTR)) → TABLAT;
(TBLPTR) + 1 → TBLPTR
if TBLRD *-,
(Prog Mem (TBLPTR)) → TABLAT;
(TBLPTR) – 1 → TBLPTR
if TBLRD +*,
(TBLPTR) + 1 → TBLPTR;
(Prog Mem (TBLPTR)) → TABLAT
Before Instruction
TABLAT
TBLPTR
MEMORY(00A356h)
After Instruction
TABLAT
TBLPTR
Example 2:
Status Affected: None
Encoding:
Description:
0000
0000
0000
TBLRD
Before Instruction
TABLAT
TBLPTR
MEMORY(01A357h)
MEMORY(01A358h)
After Instruction
TABLAT
TBLPTR
*+ ;
=
=
=
55h
00A356h
34h
=
=
34h
00A357h
+* ;
=
=
=
=
AAh
01A357h
12h
34h
=
=
34h
01A358h
10nn
nn=0 *
=1 *+
=2 *=3 +*
This instruction is used to read the contents
of Program Memory (P.M.). To address the
program memory, a pointer called Table
Pointer (TBLPTR) is used.
The TBLPTR (a 21-bit pointer) points to
each byte in the program memory. TBLPTR
has a 2-Mbyte address range.
TBLPTR[0] = 0: Least Significant Byte of
Program Memory Word
TBLPTR[0] = 1: Most Significant Byte of
Program Memory Word
The TBLRD instruction can modify the value
of TBLPTR as follows:
• no change
• post-increment
• post-decrement
• pre-increment
Words:
1
Cycles:
2
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
No
operation
No
operation
No
operation
No
operation
No operation
(Read Program
Memory)
No
operation
No operation
(Write
TABLAT)
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 333
PIC18F85J90 FAMILY
TBLWT
Table Write
TBLWT
Table Write (Continued)
Syntax:
TBLWT ( *; *+; *-; +*)
Example 1:
TBLWT *+;
Operands:
None
Operation:
if TBLWT*,
(TABLAT) → Holding Register;
TBLPTR – No Change
if TBLWT*+,
(TABLAT) → Holding Register;
(TBLPTR) + 1 → TBLPTR
if TBLWT*-,
(TABLAT) → Holding Register;
(TBLPTR) – 1 → TBLPTR
if TBLWT+*,
(TBLPTR) + 1 → TBLPTR;
(TABLAT) → Holding Register
Status Affected:
Example 2:
None
Encoding:
Description:
Before Instruction
TABLAT
=
55h
TBLPTR
=
00A356h
HOLDING REGISTER
(00A356h)
=
FFh
After Instructions (table write completion)
TABLAT
=
55h
TBLPTR
=
00A357h
HOLDING REGISTER
(00A356h)
=
55h
0000
0000
0000
11nn
nn=0 *
=1 *+
=2 *=3 +*
This instruction uses the 3 LSBs of
TBLPTR to determine which of the
8 holding registers the TABLAT is written
to. The holding registers are used to
program the contents of Program Memory
(P.M.). (Refer to Section 5.0 “Memory
Organization” for additional details on
programming Flash memory.)
TBLWT +*;
Before Instruction
TABLAT
=
34h
TBLPTR
=
01389Ah
HOLDING REGISTER
(01389Ah)
=
FFh
HOLDING REGISTER
(01389Bh)
=
FFh
After Instruction (table write completion)
TABLAT
=
34h
TBLPTR
=
01389Bh
HOLDING REGISTER
(01389Ah)
=
FFh
HOLDING REGISTER
(01389Bh)
=
34h
The TBLPTR (a 21-bit pointer) points to
each byte in the program memory.
TBLPTR has a 2-Mbyte address range.
The LSb of the TBLPTR selects which
byte of the program memory location to
access.
TBLPTR[0] = 0: Least Significant Byte
of Program Memory
Word
TBLPTR[0] = 1: Most Significant Byte
of Program Memory
Word
The TBLWT instruction can modify the
value of TBLPTR as follows:
•
•
•
•
no change
post-increment
post-decrement
pre-increment
Words:
1
Cycles:
2
Q Cycle Activity:
Q1
Decode
Q2
Q3
Q4
No
No
No
operation operation operation
No
No
No
No
operation operation operation operation
(Read
(Write to
TABLAT)
Holding
Register)
DS39770B-page 334
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TSTFSZ
Test f, Skip if 0
XORLW
Exclusive OR Literal with W
Syntax:
TSTFSZ f {,a}
Syntax:
XORLW k
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
Operands:
0 ≤ k ≤ 255
Operation:
(W) .XOR. k → W
Operation:
skip if f = 0
Status Affected:
N, Z
Status Affected:
None
Encoding:
Encoding:
0110
Description:
011a
ffff
ffff
If ‘f’ = 0, the next instruction fetched
during the current instruction execution
is discarded and a NOP is executed,
making this a two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
0000
1010
kkkk
kkkk
Description:
The contents of W are XORed with
the 8-bit literal ‘k’. The result is placed
in W.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write to
W
Example:
Before Instruction
W
=
After Instruction
W
=
XORLW
0AFh
B5h
1Ah
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
No
operation
If skip:
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
If skip and followed by 2-word instruction:
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Example:
HERE
NZERO
ZERO
Before Instruction
PC
After Instruction
If CNT
PC
If CNT
PC
TSTFSZ
:
:
CNT, 1
=
Address (HERE)
=
=
≠
=
00h,
Address (ZERO)
00h,
Address (NZERO)
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 335
PIC18F85J90 FAMILY
XORWF
Exclusive OR W with f
Syntax:
XORWF
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(W) .XOR. (f) → dest
Status Affected:
N, Z
Encoding:
0001
Description:
f {,d {,a}}
10da
ffff
ffff
Exclusive OR the contents of W with
register ‘f’. If ‘d’ is ‘0’, the result is stored
in W. If ‘d’ is ‘1’, the result is stored back
in the register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
XORWF
Before Instruction
REG
=
W
=
After Instruction
REG
=
W
=
DS39770B-page 336
REG, 1, 0
AFh
B5h
1Ah
B5h
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
23.2
Extended Instruction Set
A summary of the instructions in the extended instruction set is provided in Table 23-3. Detailed descriptions
are provided in Section 23.2.2 “Extended Instruction
Set”. The opcode field descriptions in Table 23-1
(page 296) apply to both the standard and extended
PIC18 instruction sets.
In addition to the standard 75 instructions of the PIC18
instruction set, the PIC18F85J90 family family of
devices also provide an optional extension to the core
CPU functionality. The added features include eight
additional instructions that augment Indirect and
Indexed Addressing operations and the implementation of Indexed Literal Offset Addressing for many of
the standard PIC18 instructions.
Note:
The additional features of the extended instruction set
are enabled by default on unprogrammed devices.
Users must properly set or clear the XINST Configuration bit during programming to enable or disable these
features.
The instructions in the extended set can all be
classified as literal operations, which either manipulate
the File Select Registers, or use them for Indexed
Addressing. Two of the instructions, ADDFSR and
SUBFSR, each have an additional special instantiation
for using FSR2. These versions (ADDULNK and
SUBULNK) allow for automatic return after execution.
23.2.1
EXTENDED INSTRUCTION SYNTAX
Most of the extended instructions use indexed arguments, using one of the File Select Registers and some
offset to specify a source or destination register. When
an argument for an instruction serves as part of
Indexed Addressing, it is enclosed in square brackets
(“[ ]”). This is done to indicate that the argument is used
as an index or offset. The MPASM™ Assembler will
flag an error if it determines that an index or offset value
is not bracketed.
The extended instructions are specifically implemented
to optimize re-entrant program code (that is, code that
is recursive or that uses a software stack) written in
high-level languages, particularly C. Among other
things, they allow users working in high-level
languages to perform certain operations on data
structures more efficiently. These include:
When the extended instruction set is enabled, brackets
are also used to indicate index arguments in
byte-oriented and bit-oriented instructions. This is in
addition to other changes in their syntax. For more
details, see Section 23.2.3.1 “Extended Instruction
Syntax with Standard PIC18 Commands”.
• Dynamic allocation and deallocation of software
stack space when entering and leaving
subroutines
• Function Pointer invocation
• Software Stack Pointer manipulation
• Manipulation of variables located in a software
stack
TABLE 23-3:
The instruction set extension and the
Indexed Literal Offset Addressing mode
were designed for optimizing applications
written in C; the user may likely never use
these instructions directly in assembler.
The syntax for these commands is
provided as a reference for users who may
be reviewing code that has been
generated by a compiler.
Note:
In the past, square brackets have been
used to denote optional arguments in the
PIC18 and earlier instruction sets. In this
text and going forward, optional
arguments are denoted by braces (“{ }”).
EXTENSIONS TO THE PIC18 INSTRUCTION SET
16-Bit Instruction Word
Mnemonic,
Operands
ADDFSR
ADDULNK
CALLW
MOVSF
f, k
k
MOVSS
zs, zd
PUSHL
k
SUBFSR
SUBULNK
f, k
k
zs, fd
Description
Cycles
MSb
Add literal to FSR
Add literal to FSR2 and return
Call subroutine using WREG
Move zs (source) to 1st word
fd (destination) 2nd word
Move zs (source) to 1st word
zd (destination) 2nd word
Store literal at FSR2,
decrement FSR2
Subtract literal from FSR
Subtract literal from FSR2 and
return
© 2007 Microchip Technology Inc.
1
2
2
2
LSb
Status
Affected
1000
1000
0000
1011
ffff
1011
xxxx
1010
ffkk
11kk
0001
0zzz
ffff
1zzz
xzzz
kkkk
kkkk
kkkk
0100
zzzz
ffff
zzzz
zzzz
kkkk
None
None
None
None
1
1110
1110
0000
1110
1111
1110
1111
1110
1
2
1110
1110
1001
1001
ffkk
11kk
kkkk
kkkk
None
None
2
Preliminary
None
None
DS39770B-page 337
PIC18F85J90 FAMILY
23.2.2
EXTENDED INSTRUCTION SET
ADDFSR
Add Literal to FSR
ADDULNK
Add Literal to FSR2 and Return
Syntax:
ADDFSR f, k
Syntax:
ADDULNK k
Operands:
0 ≤ k ≤ 63
f ∈ [ 0, 1, 2 ]
Operands:
0 ≤ k ≤ 63
Operation:
FSR2 + k → FSR2,
(TOS) → PC
Status Affected:
None
Operation:
FSR(f) + k → FSR(f)
Status Affected:
None
Encoding:
1110
1000
ffkk
kkkk
Description:
The 6-bit literal ‘k’ is added to the
contents of the FSR specified by ‘f’.
Words:
1
Cycles:
1
Encoding:
1110
Description:
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write to
FSR
Example:
After Instruction
FSR2
=
03FFh
Words:
1
Cycles:
2
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write to
FSR
No
Operation
No
Operation
No
Operation
No
Operation
0422h
Example:
Note:
kkkk
This may be thought of as a special
case of the ADDFSR instruction,
where f = 3 (binary ‘11’); it operates
only on FSR2.
ADDFSR 2, 23h
Before Instruction
FSR2
=
11kk
The instruction takes two cycles to
execute; a NOP is performed during
the second cycle.
Q Cycle Activity:
Q1
1000
The 6-bit literal ‘k’ is added to the
contents of FSR2. A RETURN is then
executed by loading the PC with the
TOS.
ADDULNK 23h
Before Instruction
FSR2
=
PC
=
03FFh
0100h
After Instruction
FSR2
=
PC
=
0422h
(TOS)
All PIC18 instructions may take an optional label argument preceding the instruction mnemonic for use in
symbolic addressing. If a label is used, the instruction format then becomes: {label} instruction argument(s).
DS39770B-page 338
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
CALLW
Subroutine Call Using WREG
MOVSF
Move Indexed to f
Syntax:
CALLW
Syntax:
MOVSF [zs], fd
Operands:
None
Operands:
Operation:
(PC + 2) → TOS,
(W) → PCL,
(PCLATH) → PCH,
(PCLATU) → PCU
0 ≤ zs ≤ 127
0 ≤ fd ≤ 4095
Operation:
((FSR2) + zs) → fd
Status Affected:
None
Status Affected:
None
Encoding:
0000
Description
0000
0001
0100
First, the return address (PC + 2) is
pushed onto the return stack. Next, the
contents of W are written to PCL; the
existing value is discarded. Then, the
contents of PCLATH and PCLATU are
latched into PCH and PCU,
respectively. The second cycle is
executed as a NOP instruction while the
new next instruction is fetched.
Encoding:
1st word (source)
2nd word (destin.)
Description:
Unlike CALL, there is no option to
update W, STATUS or BSR.
Words:
1
Cycles:
2
1110
1111
Q1
Q2
Q3
Q4
Read
WREG
Push PC to
stack
No
operation
No
operation
No
operation
No
operation
No
operation
The contents of the source register are
moved to destination register ‘fd’. The
actual address of the source register is
determined by adding the 7-bit literal
offset ‘zs’, in the first word, to the value
of FSR2. The address of the destination
register is specified by the 12-bit literal
‘fd’ in the second word. Both addresses
can be anywhere in the 4096-byte data
space (000h to FFFh).
Words:
2
Cycles:
2
Q Cycle Activity:
Q1
Decode
Before Instruction
PC
=
PCLATH =
PCLATU =
W
=
After Instruction
PC
=
TOS
=
PCLATH =
PCLATU =
W
=
CALLW
Decode
address (HERE)
10h
00h
06h
001006h
address (HERE + 2)
10h
00h
06h
© 2007 Microchip Technology Inc.
zzzzs
ffffd
If the resultant source address points to
an Indirect Addressing register, the
value returned will be 00h.
Decode
HERE
0zzz
ffff
The MOVSF instruction cannot use the
PCL, TOSU, TOSH or TOSL as the
destination register.
Q Cycle Activity:
Example:
1011
ffff
Q2
Q3
Determine
Determine
source addr source addr
No
operation
No
operation
No dummy
read
Example:
MOVSF
Before Instruction
FSR2
Contents
of 85h
REG2
After Instruction
FSR2
Contents
of 85h
REG2
Preliminary
Q4
Read
source reg
Write
register ‘f’
(dest)
[05h], REG2
=
80h
=
=
33h
11h
=
80h
=
=
33h
33h
DS39770B-page 339
PIC18F85J90 FAMILY
MOVSS
Move Indexed to Indexed
PUSHL
Store Literal at FSR2, Decrement FSR2
Syntax:
MOVSS [zs], [zd]
Syntax:
PUSHL k
Operands:
0 ≤ zs ≤ 127
0 ≤ zd ≤ 127
Operands:
0 ≤ k ≤ 255
Operation:
k → (FSR2),
FSR2 – 1 → FSR2
Status Affected:
None
Operation:
((FSR2) + zs) → ((FSR2) + zd)
Status Affected:
None
Encoding:
1st word (source)
2nd word (dest.)
1110
1111
Description
1011
xxxx
1zzz
xzzz
zzzzs
zzzzd
The contents of the source register are
moved to the destination register. The
addresses of the source and destination
registers are determined by adding the
7-bit literal offsets, ‘zs’ or ‘zd’,
respectively, to the value of FSR2. Both
registers can be located anywhere in
the 4096-byte data memory space
(000h to FFFh).
Encoding:
Words:
2
Cycles:
2
Words:
1
Cycles:
Q1
Decode
Q2
Q3
Determine
Determine
source addr source addr
Determine
dest addr
Example:
kkkk
1
Q1
Q2
Q3
Q4
Decode
Read ‘k’
Process
data
Write to
destination
Example:
PUSHL 08h
Before Instruction
FSR2H:FSR2L
Memory (01ECh)
=
=
01ECh
00h
After Instruction
FSR2H:FSR2L
Memory (01ECh)
=
=
01EBh
08h
Q4
Read
source reg
Write
to dest reg
MOVSS [05h], [06h]
Before Instruction
FSR2
Contents
of 85h
Contents
of 86h
After Instruction
FSR2
Contents
of 85h
Contents
of 86h
DS39770B-page 340
Determine
dest addr
kkkk
Q Cycle Activity:
Q Cycle Activity:
Decode
1010
The 8-bit literal ‘k’ is written to the data
memory address specified by FSR2.
FSR2 is decremented by 1 after the
operation.
This instruction allows users to push
values onto a software stack.
The MOVSS instruction cannot use the
PCL, TOSU, TOSH or TOSL as the
destination register.
If the resultant source address points to
an Indirect Addressing register, the
value returned will be 00h. If the
resultant destination address points to
an Indirect Addressing register, the
instruction will execute as a NOP.
1111
Description:
=
80h
=
33h
=
11h
=
80h
=
33h
=
33h
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
SUBFSR
Subtract Literal from FSR
SUBULNK
Syntax:
SUBFSR f, k
Syntax:
SUBULNK k
Operands:
0 ≤ k ≤ 63
Operands:
0 ≤ k ≤ 63
f ∈ [ 0, 1, 2 ]
Operation:
Operation:
FSRf – k → FSRf
FSR2 – k → FSR2,
(TOS) → PC
Status Affected:
None
Status Affected:
None
Encoding:
1110
1001
ffkk
kkkk
Description:
The 6-bit literal ‘k’ is subtracted from
the contents of the FSR specified
by ‘f’.
Words:
1
Cycles:
1
Encoding:
1110
Description:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Before Instruction
FSR2
=
After Instruction
FSR2
=
SUBFSR 2, 23h
1001
11kk
kkkk
The 6-bit literal ‘k’ is subtracted from the
contents of the FSR2. A RETURN is then
executed by loading the PC with the
TOS.
The instruction takes two cycles to
execute; a NOP is performed during the
second cycle.
Q Cycle Activity:
Example:
Subtract Literal from FSR2 and Return
This may be thought of as a special case
of the SUBFSR instruction, where f = 3
(binary ‘11’); it operates only on FSR2.
Words:
1
Cycles:
2
Q Cycle Activity:
03FFh
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
No
Operation
No
Operation
No
Operation
No
Operation
03DCh
Example:
© 2007 Microchip Technology Inc.
Preliminary
SUBULNK 23h
Before Instruction
FSR2
=
PC
=
03FFh
0100h
After Instruction
FSR2
=
PC
=
03DCh
(TOS)
DS39770B-page 341
PIC18F85J90 FAMILY
23.2.3
Note:
BYTE-ORIENTED AND
BIT-ORIENTED INSTRUCTIONS IN
INDEXED LITERAL OFFSET MODE
Enabling the PIC18 instruction set extension may cause legacy applications to
behave erratically or fail entirely.
In addition to eight new commands in the extended set,
enabling the extended instruction set also enables
Indexed Literal Offset Addressing (Section 5.6.1
“Indexed Addressing with Literal Offset”). This has
a significant impact on the way that many commands of
the standard PIC18 instruction set are interpreted.
When the extended set is disabled, addresses embedded in opcodes are treated as literal memory locations:
either as a location in the Access Bank (a = 0) or in a
GPR bank designated by the BSR (a = 1). When the
extended instruction set is enabled and a = 0, however,
a file register argument of 5Fh or less is interpreted as
an offset from the pointer value in FSR2 and not as a
literal address. For practical purposes, this means that
all instructions that use the Access RAM bit as an
argument – that is, all byte-oriented and bit-oriented
instructions, or almost half of the core PIC18 instructions – may behave differently when the extended
instruction set is enabled.
When the content of FSR2 is 00h, the boundaries of the
Access RAM are essentially remapped to their original
values. This may be useful in creating
backward-compatible code. If this technique is used, it
may be necessary to save the value of FSR2 and
restore it when moving back and forth between C and
assembly routines in order to preserve the Stack
Pointer. Users must also keep in mind the syntax
requirements of the extended instruction set (see
Section 23.2.3.1 “Extended Instruction Syntax with
Standard PIC18 Commands”).
Although the Indexed Literal Offset mode can be very
useful for dynamic stack and pointer manipulation, it
can also be very annoying if a simple arithmetic operation is carried out on the wrong register. Users who are
accustomed to the PIC18 programming must keep in
mind that, when the extended instruction set is
enabled, register addresses of 5Fh or less are used for
Indexed Literal Offset Addressing.
Representative examples of typical byte-oriented and
bit-oriented instructions in the Indexed Literal Offset
mode are provided on the following page to show how
execution is affected. The operand conditions shown in
the examples are applicable to all instructions of these
types.
DS39770B-page 342
23.2.3.1
Extended Instruction Syntax with
Standard PIC18 Commands
When the extended instruction set is enabled, the file
register argument ‘f’ in the standard byte-oriented and
bit-oriented commands is replaced with the literal offset
value ‘k’. As already noted, this occurs only when ‘f’ is
less than or equal to 5Fh. When an offset value is used,
it must be indicated by square brackets (“[ ]”). As with
the extended instructions, the use of brackets indicates
to the compiler that the value is to be interpreted as an
index or an offset. Omitting the brackets, or using a
value greater than 5Fh within the brackets, will
generate an error in the MPASM Assembler.
If the index argument is properly bracketed for Indexed
Literal Offset Addressing, the Access RAM argument is
never specified; it will automatically be assumed to be
‘0’. This is in contrast to standard operation (extended
instruction set disabled), when ‘a’ is set on the basis of
the target address. Declaring the Access RAM bit in
this mode will also generate an error in the MPASM
Assembler.
The destination argument ‘d’ functions as before.
In the latest versions of the MPASM Assembler,
language support for the extended instruction set must
be explicitly invoked. This is done with either the
command line option, /y, or the PE directive in the
source listing.
23.2.4
CONSIDERATIONS WHEN
ENABLING THE EXTENDED
INSTRUCTION SET
It is important to note that the extensions to the instruction set may not be beneficial to all users. In particular,
users who are not writing code that uses a software
stack may not benefit from using the extensions to the
instruction set.
Additionally, the Indexed Literal Offset Addressing
mode may create issues with legacy applications
written to the PIC18 assembler. This is because
instructions in the legacy code may attempt to address
registers in the Access Bank below 5Fh. Since these
addresses are interpreted as literal offsets to FSR2
when the instruction set extension is enabled, the
application may read or write to the wrong data
addresses.
When porting an application to the PIC18F85J90 family
family, it is very important to consider the type of code.
A large, re-entrant application that is written in C and
would benefit from efficient compilation will do well
when using the instruction set extensions. Legacy
applications that heavily use the Access Bank will most
likely not benefit from using the extended instruction
set.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
ADD W to Indexed
(Indexed Literal Offset mode)
BSF
Bit Set Indexed
(Indexed Literal Offset mode)
Syntax:
ADDWF
Syntax:
BSF [k], b
Operands:
0 ≤ k ≤ 95
d ∈ [0,1]
Operands:
0 ≤ f ≤ 95
0≤b≤7
Operation:
(W) + ((FSR2) + k) → dest
Operation:
1 → ((FSR2) + k)<b>
Status Affected:
N, OV, C, DC, Z
Status Affected:
None
ADDWF
Encoding:
[k] {,d}
0010
Description:
01d0
kkkk
kkkk
The contents of W are added to the
contents of the register indicated by
FSR2, offset by the value ‘k’.
If ‘d’ is ‘0’, the result is stored in W. If ‘d’
is ‘1’, the result is stored back in
register ‘f’ (default).
Words:
Encoding:
bbb0
kkkk
kkkk
Description:
Bit ‘b’ of the register indicated by FSR2,
offset by the value ‘k’, is set.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
1
Cycles:
1000
1
Q Cycle Activity:
Example:
Q1
Q2
Q3
Q4
Decode
Read ‘k’
Process
Data
Write to
destination
Example:
ADDWF
Before Instruction
W
OFST
FSR2
Contents
of 0A2Ch
After Instruction
W
Contents
of 0A2Ch
Before Instruction
FLAG_OFST
FSR2
Contents
of 0A0Ah
After Instruction
Contents
of 0A0Ah
[OFST] ,0
=
=
=
17h
2Ch
0A00h
=
20h
=
37h
=
20h
BSF
[FLAG_OFST], 7
=
=
0Ah
0A00h
=
55h
=
D5h
SETF
Set Indexed
(Indexed Literal Offset mode)
Syntax:
SETF [k]
Operands:
0 ≤ k ≤ 95
Operation:
FFh → ((FSR2) + k)
Status Affected:
None
Encoding:
0110
1000
kkkk
kkkk
Description:
The contents of the register indicated by
FSR2, offset by ‘k’, are set to FFh.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read ‘k’
Process
Data
Write
register
Example:
SETF
Before Instruction
OFST
FSR2
Contents
of 0A2Ch
After Instruction
Contents
of 0A2Ch
© 2007 Microchip Technology Inc.
Preliminary
[OFST]
=
=
2Ch
0A00h
=
00h
=
FFh
DS39770B-page 343
PIC18F85J90 FAMILY
23.2.5
SPECIAL CONSIDERATIONS WITH
MICROCHIP MPLAB® IDE TOOLS
The latest versions of Microchip’s software tools have
been designed to fully support the extended instruction
set for the PIC18F85J90 family family. This includes
the MPLAB C18 C Compiler, MPASM assembly
language and MPLAB Integrated Development
Environment (IDE).
When selecting a target device for software
development, MPLAB IDE will automatically set default
Configuration bits for that device. The default setting for
the XINST Configuration bit is ‘0’, disabling the
extended instruction set and Indexed Literal Offset
Addressing. For proper execution of applications
developed to take advantage of the extended
instruction set, XINST must be set during
programming.
DS39770B-page 344
To develop software for the extended instruction set,
the user must enable support for the instructions and
the Indexed Addressing mode in their language tool(s).
Depending on the environment being used, this may be
done in several ways:
• A menu option or dialog box within the
environment that allows the user to configure the
language tool and its settings for the project
• A command line option
• A directive in the source code
These options vary between different compilers,
assemblers and development environments. Users are
encouraged to review the documentation accompanying their development systems for the appropriate
information.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
24.0
DEVELOPMENT SUPPORT
24.1
The PIC® microcontrollers are supported with a full
range of hardware and software development tools:
• Integrated Development Environment
- MPLAB® IDE Software
• Assemblers/Compilers/Linkers
- MPASMTM Assembler
- MPLAB C18 and MPLAB C30 C Compilers
- MPLINKTM Object Linker/
MPLIBTM Object Librarian
- MPLAB ASM30 Assembler/Linker/Library
• Simulators
- MPLAB SIM Software Simulator
• Emulators
- MPLAB ICE 2000 In-Circuit Emulator
- MPLAB REAL ICE™ In-Circuit Emulator
• In-Circuit Debugger
- MPLAB ICD 2
• Device Programmers
- PICSTART® Plus Development Programmer
- MPLAB PM3 Device Programmer
- PICkit™ 2 Development Programmer
• Low-Cost Demonstration and Development
Boards and Evaluation Kits
MPLAB Integrated Development
Environment Software
The MPLAB IDE software brings an ease of software
development previously unseen in the 8/16-bit microcontroller market. The MPLAB IDE is a Windows®
operating system-based application that contains:
• A single graphical interface to all debugging tools
- Simulator
- Programmer (sold separately)
- Emulator (sold separately)
- In-Circuit Debugger (sold separately)
• A full-featured editor with color-coded context
• A multiple project manager
• Customizable data windows with direct edit of
contents
• High-level source code debugging
• Visual device initializer for easy register
initialization
• Mouse over variable inspection
• Drag and drop variables from source to watch
windows
• Extensive on-line help
• Integration of select third party tools, such as
HI-TECH Software C Compilers and IAR
C Compilers
The MPLAB IDE allows you to:
• Edit your source files (either assembly or C)
• One touch assemble (or compile) and download
to PIC MCU emulator and simulator tools
(automatically updates all project information)
• Debug using:
- Source files (assembly or C)
- Mixed assembly and C
- Machine code
MPLAB IDE supports multiple debugging tools in a
single development paradigm, from the cost-effective
simulators, through low-cost in-circuit debuggers, to
full-featured emulators. This eliminates the learning
curve when upgrading to tools with increased flexibility
and power.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 345
PIC18F85J90 FAMILY
24.2
MPASM Assembler
24.5
The MPASM Assembler is a full-featured, universal
macro assembler for all PIC MCUs.
The MPASM Assembler generates relocatable object
files for the MPLINK Object Linker, Intel® standard HEX
files, MAP files to detail memory usage and symbol
reference, absolute LST files that contain source lines
and generated machine code and COFF files for
debugging.
The MPASM Assembler features include:
MPLAB ASM30 Assembler produces relocatable
machine code from symbolic assembly language for
dsPIC30F devices. MPLAB C30 C Compiler uses the
assembler to produce its object file. The assembler
generates relocatable object files that can then be
archived or linked with other relocatable object files and
archives to create an executable file. Notable features
of the assembler include:
•
•
•
•
•
•
• Integration into MPLAB IDE projects
• User-defined macros to streamline
assembly code
• Conditional assembly for multi-purpose
source files
• Directives that allow complete control over the
assembly process
Support for the entire dsPIC30F instruction set
Support for fixed-point and floating-point data
Command line interface
Rich directive set
Flexible macro language
MPLAB IDE compatibility
24.6
24.3
MPLAB C18 and MPLAB C30
C Compilers
The MPLAB C18 and MPLAB C30 Code Development
Systems are complete ANSI C compilers for
Microchip’s PIC18 and PIC24 families of microcontrollers and the dsPIC30 and dsPIC33 family of digital signal controllers. These compilers provide powerful
integration capabilities, superior code optimization and
ease of use not found with other compilers.
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
24.4
MPLINK Object Linker/
MPLIB Object Librarian
The MPLINK Object Linker combines relocatable
objects created by the MPASM Assembler and the
MPLAB C18 C Compiler. It can link relocatable objects
from precompiled libraries, using directives from a
linker script.
MPLAB ASM30 Assembler, Linker
and Librarian
MPLAB SIM Software Simulator
The MPLAB SIM Software Simulator allows code
development in a PC-hosted environment by simulating the PIC MCUs and dsPIC® DSCs on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a comprehensive stimulus controller. Registers can be
logged to files for further run-time analysis. The trace
buffer and logic analyzer display extend the power of
the simulator to record and track program execution,
actions on I/O, most peripherals and internal registers.
The MPLAB SIM Software Simulator fully supports
symbolic debugging using the MPLAB C18 and
MPLAB C30 C Compilers, and the MPASM and
MPLAB ASM30 Assemblers. The software simulator
offers the flexibility to develop and debug code outside
of the hardware laboratory environment, making it an
excellent, economical software development tool.
The MPLIB Object Librarian manages the creation and
modification of library files of precompiled code. When
a routine from a library is called from a source file, only
the modules that contain that routine will be linked in
with the application. This allows large libraries to be
used efficiently in many different applications.
The object linker/library features include:
• Efficient linking of single libraries instead of many
smaller files
• Enhanced code maintainability by grouping
related modules together
• Flexible creation of libraries with easy module
listing, replacement, deletion and extraction
DS39770B-page 346
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
24.7
MPLAB ICE 2000
High-Performance
In-Circuit Emulator
24.9
The MPLAB ICE 2000 In-Circuit Emulator is intended
to provide the product development engineer with a
complete microcontroller design tool set for PIC
microcontrollers. Software control of the MPLAB ICE
2000 In-Circuit Emulator is advanced by the MPLAB
Integrated Development Environment, which allows
editing, building, downloading and source debugging
from a single environment.
The MPLAB ICE 2000 is a full-featured emulator
system with enhanced trace, trigger and data monitoring features. Interchangeable processor modules allow
the system to be easily reconfigured for emulation of
different processors. The architecture of the MPLAB
ICE 2000 In-Circuit Emulator allows expansion to
support new PIC microcontrollers.
The MPLAB ICE 2000 In-Circuit Emulator system has
been designed as a real-time emulation system with
advanced features that are typically found on more
expensive development tools. The PC platform and
Microsoft® Windows® 32-bit operating system were
chosen to best make these features available in a
simple, unified application.
24.8
MPLAB REAL ICE In-Circuit
Emulator System
MPLAB REAL ICE In-Circuit Emulator System is
Microchip’s next generation high-speed emulator for
Microchip Flash DSC® and MCU devices. It debugs and
programs PIC® and dsPIC® Flash microcontrollers with
the easy-to-use, powerful graphical user interface of the
MPLAB Integrated Development Environment (IDE),
included with each kit.
The MPLAB REAL ICE probe is connected to the design
engineer’s PC using a high-speed USB 2.0 interface and
is connected to the target with either a connector
compatible with the popular MPLAB ICD 2 system
(RJ11) or with the new high speed, noise tolerant, lowvoltage differential signal (LVDS) interconnection
(CAT5).
MPLAB ICD 2 In-Circuit Debugger
Microchip’s In-Circuit Debugger, MPLAB ICD 2, is a
powerful, low-cost, run-time development tool,
connecting to the host PC via an RS-232 or high-speed
USB interface. This tool is based on the Flash PIC
MCUs and can be used to develop for these and other
PIC MCUs and dsPIC DSCs. The MPLAB ICD 2 utilizes
the in-circuit debugging capability built into the Flash
devices. This feature, along with Microchip’s In-Circuit
Serial ProgrammingTM (ICSPTM) protocol, offers costeffective, in-circuit Flash debugging from the graphical
user interface of the MPLAB Integrated Development
Environment. This enables a designer to develop and
debug source code by setting breakpoints, single stepping and watching variables, and CPU status and
peripheral registers. Running at full speed enables
testing hardware and applications in real time. MPLAB
ICD 2 also serves as a development programmer for
selected PIC devices.
24.10 MPLAB PM3 Device Programmer
The MPLAB PM3 Device Programmer is a universal,
CE compliant device programmer with programmable
voltage verification at VDDMIN and VDDMAX for
maximum reliability. It features a large LCD display
(128 x 64) for menus and error messages and a modular, detachable socket assembly to support various
package types. The ICSP™ cable assembly is included
as a standard item. In Stand-Alone mode, the MPLAB
PM3 Device Programmer can read, verify and program
PIC devices without a PC connection. It can also set
code protection in this mode. The MPLAB PM3
connects to the host PC via an RS-232 or USB cable.
The MPLAB PM3 has high-speed communications and
optimized algorithms for quick programming of large
memory devices and incorporates an SD/MMC card for
file storage and secure data applications.
MPLAB REAL ICE is field upgradeable through future
firmware downloads in MPLAB IDE. In upcoming
releases of MPLAB IDE, new devices will be supported,
and new features will be added, such as software breakpoints and assembly code trace. MPLAB REAL ICE
offers significant advantages over competitive emulators
including low-cost, full-speed emulation, real-time
variable watches, trace analysis, complex breakpoints, a
ruggedized probe interface and long (up to three meters)
interconnection cables.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 347
PIC18F85J90 FAMILY
24.11 PICSTART Plus Development
Programmer
24.13 Demonstration, Development and
Evaluation Boards
The PICSTART Plus Development Programmer is an
easy-to-use, low-cost, prototype programmer. It
connects to the PC via a COM (RS-232) port. MPLAB
Integrated Development Environment software makes
using the programmer simple and efficient. The
PICSTART Plus Development Programmer supports
most PIC devices in DIP packages up to 40 pins.
Larger pin count devices, such as the PIC16C92X and
PIC17C76X, may be supported with an adapter socket.
The PICSTART Plus Development Programmer is CE
compliant.
A wide variety of demonstration, development and
evaluation boards for various PIC MCUs and dsPIC
DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for
adding custom circuitry and provide application firmware
and source code for examination and modification.
24.12 PICkit 2 Development Programmer
The PICkit™ 2 Development Programmer is a low-cost
programmer and selected Flash device debugger with
an easy-to-use interface for programming many of
Microchip’s baseline, mid-range and PIC18F families of
Flash memory microcontrollers. The PICkit 2 Starter Kit
includes a prototyping development board, twelve
sequential lessons, software and HI-TECH’s PICC™
Lite C compiler, and is designed to help get up to speed
quickly using PIC® microcontrollers. The kit provides
everything needed to program, evaluate and develop
applications using Microchip’s powerful, mid-range
Flash memory family of microcontrollers.
DS39770B-page 348
The boards support a variety of features, including LEDs,
temperature sensors, switches, speakers, RS-232
interfaces, LCD displays, potentiometers and additional
EEPROM memory.
The demonstration and development boards can be
used in teaching environments, for prototyping custom
circuits and for learning about various microcontroller
applications.
In addition to the PICDEM™ and dsPICDEM™ demonstration/development board series of circuits, Microchip
has a line of evaluation kits and demonstration software
for analog filter design, KEELOQ® security ICs, CAN,
IrDA®, PowerSmart® battery management, SEEVAL®
evaluation system, Sigma-Delta ADC, flow rate
sensing, plus many more.
Check the Microchip web page (www.microchip.com)
and the latest “Product Selector Guide” (DS00148) for
the complete list of demonstration, development and
evaluation kits.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
25.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings(†)
Ambient temperature under bias.............................................................................................................-40°C to +100°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on any digital only I/O pin or MCLR with respect to VSS (except VDD) ........................................... -0.3V to 6.0V
Voltage on any combined digital and analog pin with respect to VSS (except VDD and MCLR)...... -0.3V to (VDD + 0.3V)
Voltage on VDDCORE with respect to VSS ................................................................................................... -0.3V to 2.75V
Voltage on VDD with respect to VSS ........................................................................................................... -0.3V to 3.6V
Total power dissipation (Note 1) ...............................................................................................................................1.0W
Maximum current out of VSS pin ...........................................................................................................................300 mA
Maximum current into VDD pin ..............................................................................................................................250 mA
Maximum output current sunk by PORTA<7:6> and any PORTB and PORTC I/O pins.........................................25 mA
Maximum output current sunk by any PORTD, PORTE and PORTJ I/O pins ..........................................................8 mA
Maximum output current sunk by PORTA<5:0> and any PORTF, PORTG and PORTH I/O pins ............................2 mA
Maximum output current sourced by PORTA<7:6> and any PORTB and PORTC I/O pins ...................................25 mA
Maximum output current sourced by any PORTD, PORTE and PORTJ I/O pins .....................................................8 mA
Maximum output current sourced by PORTA<5:0> and any PORTF, PORTG and PORTH I/O pins .......................2 mA
Maximum current sunk by all ports combined.......................................................................................................200 mA
Note 1: Power dissipation is calculated as follows:
Pdis = VDD x {IDD – ∑ IOH} + ∑ {(VDD – VOH) x IOH} + ∑(VOL x IOL)
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 349
PIC18F85J90 FAMILY
FIGURE 25-1:
PIC18F85J90 FAMILY VOLTAGE-FREQUENCY GRAPH,
REGULATOR ENABLED (INDUSTRIAL)(1)
4.0V
3.6V
Voltage (VDD)
3.5V
3.0V
PIC18F6XJ90/8XJ90
2.5V
2.35V
2.0V
0
Note 1:
8 MHz
Frequency
40 MHz
When the on-chip regulator is enabled, its BOR circuit will automatically trigger a device Reset
before VDD reaches a level at which full-speed operation is not possible.
FIGURE 25-2:
PIC18F85J90 FAMILY VOLTAGE-FREQUENCY GRAPH,
REGULATOR DISABLED (INDUSTRIAL)(1,2)
3.00V
Voltage (VDDCORE)
2.75V
2.7V
2.50V
PIC18F6XJ90/8XJ90
2.35V
2.25V
2.00V
40 MHz
8 MHz
Frequency
Note 1:
2:
For frequencies between 4 MHz and 40 MHz, FMAX = (51.42 MHz/V) * (VDDCORE – 2V) + 4 MHz.
When the on-chip voltage regulator is disabled, VDD and VDDCORE must be maintained so that
VDDCORE ≤ VDD ≤ 3.6V.
DS39770B-page 350
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
25.1
DC Characteristics:
Supply Voltage
PIC18F85J90 Family (Industrial)
PIC18F85J90 Family
(Industrial)
Param
Symbol
No.
D001
VDD
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Characteristic
Supply Voltage
D001B VDDCORE External Supply for
Microcontroller Core
Min
Typ
Max
Units
VDDCORE
2.0
—
—
3.6
3.6
V
V
ENVREG tied to VSS
ENVREG tied to VDD
2.0
—
2.70
V
ENVREG tied to VSS
D001C AVDD
Analog Supply Voltage
VDD – 0.3
—
VDD + 0.3
V
D001D AVSS
Analog Ground Potential VSS – 0.3
—
VSS + 0.3
V
D002
VDR
RAM Data Retention
Voltage(1)
1.5
—
—
V
D003
VPOR
VDD Start Voltage
to ensure internal
Power-on Reset signal
—
—
0.7
V
D004
SVDD
VDD Rise Rate
to ensure internal
Power-on Reset signal
0.05
—
—
D005
VBOR
Brown-out Reset Voltage
—
1.8
—
Note 1:
Conditions
See Section 4.3 “Power-on
Reset (POR)” for details
V/ms See Section 4.3 “Power-on
Reset (POR)” for details
V
This is the limit to which VDD can be lowered in Sleep mode, or during a device Reset, without losing RAM data.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 351
PIC18F85J90 FAMILY
25.2
DC Characteristics:
PIC18F85J90 Family
(Industrial)
Param
No.
Power-Down and Supply Current
PIC18F85J90 Family (Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Device
Typ
Max
Units
Conditions
0.2
0.9
µA
-40°C
0.1
0.9
µA
+25°C
2.4
5
µA
+85°C
0.5
0.9
µA
-40°C
0.1
0.9
µA
+25°C
2.7
5
µA
+85°C
2.7
6
µA
-40°C
3.5
6
µA
+25°C
6.7
12
µA
+85°C
Power-Down Current (IPD)(1)
All devices
All devices
All devices
Note 1:
2:
3:
4:
5:
6:
7:
VDD = 2.0V,
VDDCORE = 2.0V
(Sleep mode)(4)
VDD = 2.5V,
VDDCORE = 2.5V
(Sleep mode)(4)
VDD = 3.3V
(Sleep mode)(5)
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
Voltage regulator disabled (ENVREG tied to VSS).
Voltage regulator enabled (ENVREG tied to VDD).
Resistor ladder current is not included.
Connecting an actual display will increase the current consumption depending on the size of the LCD.
DS39770B-page 352
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
25.2
DC Characteristics:
PIC18F85J90 Family
(Industrial)
Param
No.
Power-Down and Supply Current
PIC18F85J90 Family (Industrial) (Continued)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Device
Typ
Max
Units
Conditions
6.5
16
µA
-40°C
7
16
µA
+25°C
9.5
20
µA
+85°C
10
18
µA
-40°C
10.5
18
µA
+25°C
12.5
24
µA
+85°C
41
100
µA
-40°C
52
100
µA
+25°C
71
110
µA
+85°C
Supply Current (IDD)(2)
All devices
All devices
All devices
All devices
All devices
All devices
All devices
All devices
All devices
Note 1:
2:
3:
4:
5:
6:
7:
359
750
µA
-40°C
387
750
µA
+25°C
407
840
µA
+85°C
438
850
µA
-40°C
470
850
µA
+25°C
491
910
µA
+85°C
486
900
µA
-40°C
526
900
µA
+25°C
+85°C
564
990
µA
0.76
1.45
mA
-40°C
0.84
1.45
mA
+25°C
0.9
1.6
mA
+85°C
1.1
1.63
mA
-40°C
1.18
1.63
mA
+25°C
1.24
1.75
mA
+85°C
1.25
1.86
mA
-40°C
1.29
1.86
mA
+25°C
1.37
1.94
mA
+85°C
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 31 kHz
(INTRC_RUN mode,
internal oscillator source)
VDD = 3.3V(5)
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 1 MHz
(INTOSC_RUN mode,
internal oscillator source)
VDD = 3.3V(5)
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 4 MHz
(INTOSC_RUN mode,
internal oscillator source)
VDD = 3.3V(5)
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
Voltage regulator disabled (ENVREG tied to VSS).
Voltage regulator enabled (ENVREG tied to VDD).
Resistor ladder current is not included.
Connecting an actual display will increase the current consumption depending on the size of the LCD.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 353
PIC18F85J90 FAMILY
25.2
DC Characteristics:
PIC18F85J90 Family
(Industrial)
Param
No.
Power-Down and Supply Current
PIC18F85J90 Family (Industrial) (Continued)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Device
Typ
Max
Units
Conditions
Supply Current (IDD)(2)
All devices
All devices
All devices
All devices
All devices
All devices
All devices
All devices
All devices
Note 1:
2:
3:
4:
5:
6:
7:
2.4
8
µA
-40°C
2.5
8
µA
+25°C
4.8
12
µA
+85°C
3.2
9
µA
-40°C
3.2
9
µA
+25°C
6
14
µA
+85°C
62
82
µA
-40°C
42
82
µA
+25°C
59
97
µA
+85°C
251
570
µA
-40°C
264
570
µA
+25°C
272
590
µA
+85°C
284
610
µA
-40°C
284
610
µA
+25°C
293
650
µA
+85°C
295
710
µA
-40°C
323
710
µA
+25°C
392
790
µA
+85°C
368
760
µA
-40°C
362
760
µA
+25°C
370
800
µA
+85°C
400
850
µA
-40°C
410
850
µA
+25°C
418
900
µA
+85°C
460
950
µA
-40°C
462
950
µA
+25°C
486
1000
µA
+85°C
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 31 kHz
(INTRC_IDLE mode,
internal oscillator source)
VDD = 3.3V(5)
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 1 MHz
(INTOSC_IDLE mode,
internal oscillator source)
VDD = 3.3V(5)
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 4 MHz
(INTOSC_IDLE mode,
internal oscillator source)
VDD = 3.3V(5)
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
Voltage regulator disabled (ENVREG tied to VSS).
Voltage regulator enabled (ENVREG tied to VDD).
Resistor ladder current is not included.
Connecting an actual display will increase the current consumption depending on the size of the LCD.
DS39770B-page 354
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
25.2
DC Characteristics:
PIC18F85J90 Family
(Industrial)
Param
No.
Power-Down and Supply Current
PIC18F85J90 Family (Industrial) (Continued)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Device
Typ
Max
Units
Conditions
165
490
µA
-40°C
180
490
µA
+25°C
200
490
µA
+85°C
256
670
µA
-40°C
260
670
µA
+25°C
280
670
µA
+85°C
460
850
µA
-40°C
456
850
µA
+25°C
482
850
µA
+85°C
Supply Current (IDD)(2)
All devices
All devices
All devices
All devices
All devices
All devices
All devices
All devices
Note 1:
2:
3:
4:
5:
6:
7:
0.632
2.2
mA
-40°C
0.681
2.2
mA
+25°C
0.738
2.2
mA
+85°C
0.912
2.5
mA
-40°C
1.04
2.5
mA
+25°C
1.04
2.5
mA
+85°C
1.32
3.0
mA
-40°C
1.32
3.0
mA
+25°C
1.41
3.0
mA
+85°C
7.47
14
mA
-40°C
5.81
14
mA
+25°C
6.32
13
mA
+85°C
8.84
18
mA
-40°C
8.66
18
mA
+25°C
7.97
16
mA
+85°C
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 1 MHZ
(PRI_RUN mode,
EC oscillator)
VDD = 3.3V(5)
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 4 MHz
(PRI_RUN mode,
EC oscillator)
VDD = 3.3V(5)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 40 MHZ
(PRI_RUN mode,
EC oscillator)
VDD = 3.3V(5)
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
Voltage regulator disabled (ENVREG tied to VSS).
Voltage regulator enabled (ENVREG tied to VDD).
Resistor ladder current is not included.
Connecting an actual display will increase the current consumption depending on the size of the LCD.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 355
PIC18F85J90 FAMILY
25.2
DC Characteristics:
PIC18F85J90 Family
(Industrial)
Param
No.
Power-Down and Supply Current
PIC18F85J90 Family (Industrial) (Continued)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Device
Typ
Max
Units
2.8
3.8
mA
Conditions
Supply Current (IDD)(2)
All devices
All devices
All devices
All devices
All devices
Note 1:
2:
3:
4:
5:
6:
7:
-40°C
3.02
3.8
mA
+25°C
3.01
4.5
mA
+85°C
4.5
5.4
mA
-40°C
4.8
5.6
mA
+25°C
4.54
5.6
mA
+85°C
5.72
6.7
mA
-40°C
5.55
6.5
mA
+25°C
5.3
6.5
mA
+85°C
7.4
8.5
mA
-40°C
7.23
8.5
mA
+25°C
6.55
7.5
mA
+85°C
9.74
11.6
mA
-40°C
9.43
11.6
mA
+25°C
8.89
10.5
mA
+85°C
VDD = 2.0V,
VDDCORE = 2.0V(4)
FOSC = 4 MHZ,
16 MHz internal
(PRI_RUN mode,
HSPLL oscillator)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 4 MHZ,
16 MHz internal
(PRI_RUN mode,
HSPLL oscillator)
(5)
VDD = 3.3V
VDD = 2.5V,
VDDCORE = 2.5V(4)
(5)
VDD = 3.3V
FOSC = 4 MHZ,
16 MHz internal
(PRI_RUN mode,
HSPLL oscillator)
FOSC = 10 MHZ,
40 MHz internal
(PRI_RUN mode,
HSPLL oscillator)
FOSC = 10 MHZ,
40 MHz internal
(PRI_RUN mode,
HSPLL oscillator)
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
Voltage regulator disabled (ENVREG tied to VSS).
Voltage regulator enabled (ENVREG tied to VDD).
Resistor ladder current is not included.
Connecting an actual display will increase the current consumption depending on the size of the LCD.
DS39770B-page 356
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
25.2
DC Characteristics:
PIC18F85J90 Family
(Industrial)
Param
No.
Power-Down and Supply Current
PIC18F85J90 Family (Industrial) (Continued)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Device
Typ
Max
Units
Conditions
50
120
µA
-40°C
51
120
µA
+25°C
+85°C
Supply Current (IDD)(2)
All devices
All devices
All devices
All devices
All devices
All devices
All devices
All devices
Note 1:
2:
3:
4:
5:
6:
7:
54
130
µA
223
480
µA
-40°C
133
300
µA
+25°C
+85°C
110
270
µA
307
550
µA
-40°C
254
500
µA
+25°C
194
460
µA
+85°C
307
850
µA
-40°C
200
850
µA
+25°C
202
800
µA
+85°C
483
950
µA
-40°C
318
950
µA
+25°C
343
900
µA
+85°C
524
1.3
mA
-40°C
474
1.2
mA
+25°C
+85°C
468
1.2
mA
2.38
8
mA
-40°C
2.04
8
mA
+25°C
2.52
9
mA
+85°C
3.02
10
mA
-40°C
2.99
10
mA
+25°C
4.23
11
mA
+85°C
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 1 MHz
(PRI_IDLE mode,
EC oscillator)
VDD = 3.3V(5)
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 4 MHz
(PRI_IDLE mode,
EC oscillator)
VDD = 3.3V(5)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 40 MHz
(PRI_IDLE mode,
EC oscillator)
VDD = 3.3V(5)
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
Voltage regulator disabled (ENVREG tied to VSS).
Voltage regulator enabled (ENVREG tied to VDD).
Resistor ladder current is not included.
Connecting an actual display will increase the current consumption depending on the size of the LCD.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 357
PIC18F85J90 FAMILY
25.2
DC Characteristics:
PIC18F85J90 Family
(Industrial)
Param
No.
Power-Down and Supply Current
PIC18F85J90 Family (Industrial) (Continued)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Device
Typ
Max
Units
Conditions
10.5
22
µA
-40°C
13.4
28
µA
+25°C
17.6
40
µA
+85°C
13.2
30
µA
-40°C
16.2
35
µA
+25°C
20.7
50
µA
+85°C
39
120
µA
-40°C
58
150
µA
+25°C
75
190
µA
+85°C
Supply Current (IDD)(2)
All devices
All devices
All devices
All devices
All devices
All devices
Note 1:
2:
3:
4:
5:
6:
7:
5.7
15
µA
-40°C
8.9
20
µA
+25°C
12.8
26
µA
+85°C
6.6
17
µA
-40°C
9.7
24
µA
+25°C
13.7
30
µA
+85°C
39
115
µA
-40°C
52.8
145
µA
+25°C
72.7
185
µA
+85°C
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 32 kHz(3)
(SEC_RUN mode,
Timer1 as clock)
VDD = 3.3V(5)
VDD = 2.0V,
VDDCORE = 2.0V(4)
VDD = 2.5V,
VDDCORE = 2.5V(4)
FOSC = 32 kHz(3)
(SEC_IDLE mode,
Timer1 as clock)
VDD = 3.3V(5)
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
Voltage regulator disabled (ENVREG tied to VSS).
Voltage regulator enabled (ENVREG tied to VDD).
Resistor ladder current is not included.
Connecting an actual display will increase the current consumption depending on the size of the LCD.
DS39770B-page 358
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
25.2
DC Characteristics:
PIC18F85J90 Family
(Industrial)
Param
No.
D022
(ΔIWDT)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Device
D025
(ΔIOSCB)
Timer1 Oscillator
A/D Converter
D026
(ΔIAD)
Note 1:
2:
3:
4:
5:
6:
7:
Typ
Max
Units
Conditions
Module Differential Currents (ΔIWDT, ΔILCD, ΔIOSCB, ΔIAD)
Watchdog Timer
1.6
4
µA
LCD Module
D024
(ΔILCD)
Power-Down and Supply Current
PIC18F85J90 Family (Industrial) (Continued)
-40°C
VDD = 2.0V,
VDDCORE = 2.0V(4)
1.7
1.6
2.5
4
4
5
µA
µA
µA
+25°C
+85°C
-40°C
2.5
2.3
3.8
5
5
6
µA
µA
µA
+25°C
+85°C
-40°C
2.6
µA
µA
+25°C
+85°C
VDD = 3.3V(5)
2.4
6
6
2(6,7)
5
µA
+25°C
VDD = 2.0V
Resistive Ladder
2.7(6,7)
5
µA
+25°C
VDD = 2.5V
3.5(6,7)
7
µA
+25°C
VDD = 3.0V
CPEN = 0;
CKSEL<1:0> = 00;
CS<1:0> = 10;
16(7)
25
µA
+25°C
VDD = 2.0V
Charge Pump
17(7)
25
µA
+25°C
VDD = 2.5V
24(7)
40
µA
+25°C
BIAS<2:0> = 111;
CPEN = 1;
CKSEL<1:0> = 11;
VDD = 2.5V,
VDDCORE = 2.5V(4)
VDD = 3.0V
6.6
12.5
µA
-40°C
7.9
11.5
7.2
8.1
11.9
7
12.5
18.5
12.5
12.5
18.5
12.5
µA
µA
µA
µA
µA
µA
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
9
11
1
12.5
18.5
1.5
µA
µA
µA
+25°C
+85°C
-40°C to +85°C
1
1.5
µA
-40°C to +85°C
VDD = 2.5V,
VDDCORE = 2.5V(4)
1
1.5
µA
-40°C to +85°C
VDD = 3.3V(5)
VDD = 2.0V,
VDDCORE = 2.0V(4)
32 kHz on Timer1(3)
VDD = 2.5V,
VDDCORE = 2.5V(4)
32 kHz on Timer1(3)
VDD = 3.3V(5)
32 kHz on Timer1(3)
VDD = 2.0V,
VDDCORE = 2.0V(4)
A/D on, not converting
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
Voltage regulator disabled (ENVREG tied to VSS).
Voltage regulator enabled (ENVREG tied to VDD).
Resistor ladder current is not included.
Connecting an actual display will increase the current consumption depending on the size of the LCD.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 359
PIC18F85J90 FAMILY
25.3
DC Characteristics:PIC18F84J90 Family (Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
DC CHARACTERISTICS
Param
Symbol
No.
VIL
Characteristic
Min
Max
Units
Conditions
Input Low Voltage
All I/O ports:
D030
with TTL buffer
VSS
0.15 VDD
V
D031
with Schmitt Trigger buffer
VSS
0.2 VDD
V
VSS
0.2 VDD
V
D032
MCLR
D033
OSC1
VSS
0.3 VDD
V
HS, HSPLL modes
D033A
OSC1
VSS
0.2 VDD
V
EC, ECPLL modes
D034
T13CKI
VSS
0.3
V
0.25 VDD + 0.8V
VDD
V
0.8 VDD
VDD
V
0.25 VDD + 0.8V
5.5
V
VDD < 3.3V
3.3V ≤ VDD ≤ 3.6V
VIH
Input High Voltage
I/O ports with analog functions:
D040
with TTL buffer
D041
with Schmitt Trigger buffer
VDD < 3.3V
Digital-only I/O ports:
with TTL buffer
with Schmitt Trigger buffer
2.0
5.5
V
0.8 VDD
5.5
V
D042
MCLR
0.8 VDD
VDD
V
D043
OSC1
0.7 VDD
VDD
V
HS, HSPLL modes
D043A
OSC1
0.8 VDD
VDD
V
EC, ECPLL modes
1.6
VDD
V
D044
T13CKI
IIL
Input Leakage Current(1)
D060
I/O ports
—
±1
μA
VSS ≤ VPIN ≤ VDD,
Pin at high-impedance
D061
MCLR
—
±1
μA
Vss ≤ VPIN ≤ VDD
OSC1
—
±5
μA
Vss ≤ VPIN ≤ VDD
30
240
μA
VDD = 3.3V, VPIN = VSS
D063
D070
Note 1:
IPU
Weak Pull-up Current
IPURB
PORTB weak pull-up current
Negative current is defined as current sourced by the pin.
DS39770B-page 360
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
25.3
DC Characteristics:PIC18F84J90 Family (Industrial) (Continued)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
DC CHARACTERISTICS
Param
Symbol
No.
Min
Max
Units
PORTA, PORTF, PORTG,
PORTH
—
0.4
V
IOL = 2 mA, VDD = 3.3V,
-40°C to +85°C
PORTD, PORTE, PORTJ
—
0.4
V
IOL = 3.4 mA, VDD = 3.3V,
-40°C to +85°C
PORTB, PORTC
—
0.4
V
IOL = 3.4 mA, VDD = 3.3V,
-40°C to +85°C
OSC2/CLKO
(EC, ECPLL modes)
—
0.4
V
IOL = 1.6 mA, VDD = 3.3V,
-40°C to +85°C
PORTA, PORTF, PORTG,
PORTH
2.4
—
V
IOH = -2 mA, VDD = 3.3V,
-40°C to +85°C
PORTD, PORTE, PORTJ
2.4
—
V
IOH = -2 mA, VDD = 3.3V,
-40°C to +85°C
PORTB, PORTC
2.4
—
V
IOH = -2 mA, VDD = 3.3V,
-40°C to +85°C
2.4
—
V
IOH = -1 mA, VDD = 3.3V,
-40°C to +85°C
D100(4) COSC2 OSC2 pin
—
15
pF
In HS mode when
external clock is used to drive
OSC1
D101
CIO
All I/O pins and OSC2
—
50
pF
To meet the AC Timing
Specifications
D102
CB
SCLx, SDAx
—
400
pF
I2C™ Specification
VOL
D080
Characteristic
Conditions
Output Low Voltage
I/O ports:
D083
VOH
D090
Output High Voltage(1)
I/O ports:
D092
OSC2/CLKO
(INTOSC, EC, ECPLL modes)
V
Capacitive Loading Specs
on Output Pins
Note 1:
Negative current is defined as current sourced by the pin.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 361
PIC18F85J90 FAMILY
TABLE 25-1:
MEMORY PROGRAMMING REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
DC CHARACTERISTICS
Param
No.
Sym
Characteristic
Min
Typ†
Max
1K
10K
—
Units
Conditions
Program Flash Memory
D130
EP
Cell Endurance
D131
VPR
VDD for Read
VMIN
—
3.6
V
VMIN = Minimum operating
voltage
D132B VPEW
VDD for Self-Timed Write
VMIN
—
3.6
V
VMIN = Minimum operating
voltage
D133A TIW
Self-Timed Write Cycle Time
—
2.8
—
ms
20
—
—
Year Provided no other
specifications are violated
mA
D134
TRETD Characteristic Retention
D135
IDDP
Supply Current during
Programming
—
3
7
D1xxx
TWE
Writes per Erase Cycle
—
—
1
E/W -40°C to +85°C
Per one physical word
address
† Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
DS39770B-page 362
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 25-2:
COMPARATOR SPECIFICATIONS
Operating Conditions: 3.0V ≤ VDD ≤ 3.6V, -40°C ≤ TA ≤ +85°C (unless otherwise stated)
Param
No.
Sym
Characteristics
Min
Typ
Max
Units
D300
VIOFF
Input Offset Voltage
—
±5.0
±10
mV
D301
VICM
Input Common Mode Voltage*
0
—
AVDD – 1.5
V
D302
CMRR
Common Mode Rejection Ratio*
55
—
—
dB
300
TRESP
Response Time(1)*
—
150
400
ns
301
TMC2OV
Comparator Mode Change to
Output Valid*
—
—
10
μs
*
Note 1:
Comments
These parameters are characterized but not tested.
Response time measured with one comparator input at (AVDD – 1.5)/2, while the other input transitions
from VSS to VDD.
TABLE 25-3:
VOLTAGE REFERENCE SPECIFICATIONS
Operating Conditions: 3.0V ≤ VDD ≤ 3.6V, -40°C ≤ TA ≤ +85°C (unless otherwise stated)
Param
No.
Sym
Characteristics
Min
Typ
Max
Units
D310
VRES
Resolution
VDD/24
—
VDD/32
LSb
D311
VRAA
Absolute Accuracy
—
—
1/2
LSb
D312
VRUR
Unit Resistor Value (R)
—
2k
—
Ω
310
TSET
Settling Time(1)
—
—
10
μs
Note 1:
Comments
Settling time measured while CVRR = 1 and CVR3:CVR0 transitions from ‘0000’ to ‘1111’.
TABLE 25-4:
INTERNAL VOLTAGE REGULATOR SPECIFICATIONS
Operating Conditions: -40°C ≤ TA ≤ +85°C (unless otherwise stated)
Param
No.
Sym
Characteristics
VRGOUT Regulator Output Voltage*
CEFC
*
External Filter Capacitor Value*
Min
Typ
Max
Units
—
2.5
—
V
4.7
10
—
μF
Comments
Capacitor must be low ESR
These parameters are characterized but not tested. Parameter numbers not yet assigned for these
specifications.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 363
PIC18F85J90 FAMILY
TABLE 25-5:
INTERNAL LCD VOLTAGE REGULATOR SPECIFICATIONS
Operating Conditions: 2.0V ≤ VDD ≤ 3.6V, -40°C ≤ TA ≤ +85°C (unless otherwise stated)
Param
No.
Sym
Characteristics
CFLY
Fly Back Capacitor
VBIAS
VPK-PK between LCDBIAS0 &
LCDBIAS3
DS39770B-page 364
Min
0.47
Typ
Max
4.7
3.40
Units
µF
Capacitor must be low ESR
V
BIAS2:BIAS0 = 111
3.27
V
BIAS2:BIAS0 = 110
3.14
V
BIAS2:BIAS0 = 101
3.01
V
BIAS2:BIAS0 = 100
2.88
V
BIAS2:BIAS0 = 011
2.75
V
BIAS2:BIAS0 = 010
2.62
V
BIAS2:BIAS0 = 001
2.49
V
BIAS2:BIAS0 = 000
Preliminary
3.6
Comments
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
25.4
25.4.1
AC (Timing) Characteristics
TIMING PARAMETER SYMBOLOGY
The timing parameter symbols have been created
following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase letters (pp) and their meanings:
pp
cc
CCP1
ck
CLKO
cs
CS
di
SDI
do
SDO
dt
Data in
io
I/O port
mc
MCLR
Uppercase letters and their meanings:
S
F
Fall
H
High
I
Invalid (High-impedance)
L
Low
I2C only
AA
output access
BUF
Bus free
TCC:ST (I2C specifications only)
CC
HD
Hold
ST
DAT
DATA input hold
STA
Start condition
© 2007 Microchip Technology Inc.
3. TCC:ST
4. Ts
(I2C specifications only)
(I2C specifications only)
T
Time
osc
rd
rw
sc
ss
t0
t1
wr
OSC1
RD
RD or WR
SCK
SS
T0CKI
T13CKI
WR
P
R
V
Z
Period
Rise
Valid
High-impedance
High
Low
High
Low
SU
Setup
STO
Stop condition
Preliminary
DS39770B-page 365
PIC18F85J90 FAMILY
25.4.2
TIMING CONDITIONS
The temperature and voltages specified in Table 25-6
apply to all timing specifications unless otherwise
noted. Figure 25-3 specifies the load conditions for the
timing specifications.
TABLE 25-6:
TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC
AC CHARACTERISTICS
FIGURE 25-3:
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Operating voltage VDD range as described in Section 25.1 and Section 25.3.
LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load Condition 1
Load Condition 2
VDD/2
RL
CL
Pin
CL
Pin
VSS
VSS
RL = 464Ω
DS39770B-page 366
CL = 50 pF
for all pins except OSC2/CLKO/RA6
and including D and E outputs as ports
CL = 15 pF
for OSC2/CLKO/RA6
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
25.4.3
TIMING DIAGRAMS AND SPECIFICATIONS
FIGURE 25-4:
EXTERNAL CLOCK TIMING
Q4
Q1
Q2
Q3
Q4
Q1
OSC1
1
3
4
3
4
2
CLKO
TABLE 25-7:
Param.
No.
1A
1
EXTERNAL CLOCK TIMING REQUIREMENTS
Symbol
FOSC
TOSC
Characteristic
Min
Max
External CLKI Frequency(1)
DC
40
MHz
ECPLL Oscillator mode
Oscillator Frequency(1)
DC
40
MHz
HSPLL Oscillator mode
External CLKI Period(1)
25
—
ns
EC Oscillator mode
25
250
ns
HS Oscillator mode
100
—
ns
TCY = 4/FOSC, Industrial
(1)
Oscillator Period
Time(1)
Units
Conditions
2
TCY
Instruction Cycle
3
TOSL,
TOSH
External Clock in (OSC1)
High or Low Time
10
—
ns
EC Oscillator mode
4
TOSR,
TOSF
External Clock in (OSC1)
Rise or Fall Time
—
7.5
ns
EC Oscillator mode
Note 1:
Instruction cycle period (TCY) equals four times the input oscillator time base period for all configurations
except PLL. All specified values are based on characterization data for that particular oscillator type under
standard operating conditions with the device executing code. Exceeding these specified limits may result
in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested
to operate at “min.” values with an external clock applied to the OSC1/CLKI pin. When an external clock
input is used, the “max.” cycle time limit is “DC” (no clock) for all devices.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 367
PIC18F85J90 FAMILY
TABLE 25-8:
Param
No.
PLL CLOCK TIMING SPECIFICATIONS (VDD = 2.15V TO 3.6V)
Sym
Characteristic
Min
Typ†
Max
4
16
—
—
10
40
Units
F10
F11
FOSC Oscillator Frequency Range
FSYS On-Chip VCO System Frequency
F12
trc
PLL Start-up Time (Lock Time)
—
—
2
ms
ΔCLK
CLKO Stability (Jitter)
-2
—
+2
%
F13
Conditions
MHz HS mode only
MHz HS mode only
† Data in “Typ” column is at 3.3V, 25°C, unless otherwise stated. These parameters are for design guidance
only and are not tested.
TABLE 25-9:
INTERNAL RC ACCURACY (INTOSC AND INTRC SOURCES)
PIC18F85J90 Family
(Industrial)
Param
No.
Device
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Min
Typ
Max
Units
Conditions
INTOSC Accuracy @ Freq = 8 MHz, 4 MHz, 2 MHz, 1 MHz, 500 kHz, 250 kHz, 125 kHz, 31 kHz(1)
All Devices
-2
+/-1
2
%
+25°C
VDD = 2.7-3.3V
-5
—
5
%
-10°C to +85°C
VDD = 2.0-3.3V
-10
+/-1
10
%
-40°C to +85°C
VDD = 2.0-3.3V
—
35.938
kHz
-40°C to +85°C
VDD = 2.0-3.3V
INTRC Accuracy @ Freq = 31 kHz(1)
All Devices
Note 1:
26.562
The accuracy specification of the 31 kHz clock is determined by which source is providing it at a given
time. When INTSRC (OSCTUNE<7>) is ‘1’, use the INTOSC accuracy specification. When INTSRC is ‘0’,
use the INTRC accuracy specification.
DS39770B-page 368
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 25-5:
CLKO AND I/O TIMING
Q1
Q4
Q2
Q3
OSC1
11
10
CLKO
13
19
14
12
18
16
I/O pin
(Input)
15
17
I/O pin
(Output)
New Value
Old Value
20, 21
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-10: CLKO AND I/O TIMING REQUIREMENTS
Param
No.
Symbol
Characteristic
Min
Typ
Max
Units Conditions
10
TOSH2CKL OSC1 ↑ to CLKO ↓
—
75
200
ns
11
TOSH2CKH OSC1 ↑ to CLKO ↑
—
75
200
ns
(Note 1)
12
TCKR
CLKO Rise Time
—
15
30
ns
(Note 1)
13
TCKF
CLKO Fall Time
—
15
30
ns
(Note 1)
14
TCKL2IOV CLKO ↓ to Port Out Valid
—
—
0.5 TCY + 20
ns
15
TIOV2CKH Port In Valid before CLKO ↑
16
TCKH2IOI
17
TOSH2IOV OSC1 ↑ (Q1 cycle) to Port Out Valid
18
TOSH2IOI
19
0.25 TCY + 25
—
—
ns
0
—
—
ns
Port In Hold after CLKO ↑
—
50
150
ns
100
—
—
ns
TIOV2OSH Port Input Valid to OSC1 ↑
(I/O in setup time)
0
—
—
ns
20
TIOR
Port Output Rise Time
—
—
6
ns
21
TIOF
Port Output Fall Time
—
—
5
ns
22†
TINP
INT pin High or Low Time
TCY
—
—
ns
23†
TRBP
RB7:RB4 Change INT High or Low Time
TCY
—
—
ns
OSC1 ↑ (Q2 cycle) to Port Input Invalid
(I/O in hold time)
(Note 1)
† These parameters are asynchronous events not related to any internal clock edges.
Note 1: Measurements are taken in EC mode, where CLKO output is 4 x TOSC.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 369
PIC18F85J90 FAMILY
FIGURE 25-6:
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND
POWER-UP TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
Oscillator
Time-out
Internal
Reset
Watchdog
Timer
Reset
31
34
34
I/O pins
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-11: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER
AND BROWN-OUT RESET REQUIREMENTS
Param.
Symbol
No.
Characteristic
Min
Typ
Max
2 TCY
10
TCY
—
4.0
4.6
Units
30
TMCL
MCLR Pulse Width (low)
31
TWDT
Watchdog Timer Time-out Period
(no postscaler)
3.4
1024 TOSC
—
1024 TOSC
—
45.8
65.5
85.2
ms
(Note 1)
ms
32
TOST
Oscillation Start-up Timer Period
33
TPWRT
Power-up Timer Period
34
TIOZ
I/O High-Impedance from MCLR
Low or Watchdog Timer Reset
—
2
—
µs
38
TCSD
CPU Start-up Time
—
10
—
µs
200
39
TIOBST
Time for INTOSC to Stabilize
—
1
µs
—
Conditions
TOSC = OSC1 period
Voltage Regulator
enabled and put to
sleep
µs
Note 1: To ensure device Reset, MCLR must be low for at least 2 TCY or 400 µs, whichever is lower.
DS39770B-page 370
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 25-7:
TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
T0CKI
41
40
42
T1OSO/T13CKI
46
45
47
48
TMR0 or
TMR1
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-12: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Param
No.
Symbol
Characteristic
40
TT0H
T0CKI High Pulse Width
41
TT0L
T0CKI Low Pulse Width
42
TT0P
T0CKI Period
No prescaler
With prescaler
No prescaler
With prescaler
No prescaler
With prescaler
45
46
47
TT1H
TT1L
T13CKI High Synchronous, no prescaler
Time
Synchronous, with prescaler
Max
Units
0.5 TCY + 20
—
ns
10
—
ns
0.5 TCY + 20
—
ns
10
—
ns
TCY + 10
—
ns
Greater of:
20 ns or
(TCY + 40)/N
—
ns
0.5 TCY + 20
—
ns
10
—
ns
Asynchronous
30
—
ns
T13CKI Low Synchronous, no prescaler
Time
Synchronous, with prescaler
0.5 TCY + 5
—
ns
10
—
ns
Asynchronous
30
—
ns
Greater of:
20 ns or
(TCY + 40)/N
—
ns
TT1P
T13CKI Input Synchronous
Period
FT 1
T13CKI Oscillator Input Frequency Range
Asynchronous
48
Min
TCKE2TMRI Delay from External T13CKI Clock Edge to
Timer Increment
© 2007 Microchip Technology Inc.
Preliminary
60
—
ns
DC
50
kHz
2 TOSC
7 TOSC
—
Conditions
N = prescale
value
(1, 2, 4,..., 256)
N = prescale
value
(1, 2, 4, 8)
DS39770B-page 371
PIC18F85J90 FAMILY
FIGURE 25-8:
CAPTURE/COMPARE/PWM TIMINGS (CCP1, CCP2 MODULES)
CCPx
(Capture Mode)
50
51
52
CCPx
(Compare or PWM Mode)
54
53
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-13: CAPTURE/COMPARE/PWM REQUIREMENTS (CCP1, CCP2 MODULES)
Param
Symbol
No.
50
51
TCCL
TCCH
Characteristic
Min
Max
Units
CCPx Input Low No prescaler
Time
With prescaler
0.5 TCY + 20
—
ns
10
—
ns
CCPx Input
High Time
0.5 TCY + 20
—
ns
10
—
ns
3 TCY + 40
N
—
ns
No prescaler
With prescaler
52
TCCP
CCPx Input Period
53
TCCR
CCPx Output Fall Time
—
25
ns
54
TCCF
CCPx Output Fall Time
—
25
ns
DS39770B-page 372
Preliminary
Conditions
N = prescale
value (1, 4 or 16)
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 25-9:
EXAMPLE SPI MASTER MODE TIMING (CKE = 0)
SS
70
SCK
(CKP = 0)
71
72
78
79
79
78
SCK
(CKP = 1)
80
bit 6 - - - - - - 1
MSb
SDO
LSb
75, 76
SDI
MSb In
bit 6 - - - - 1
LSb In
74
73
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-14: EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 0)
Param
No.
Symbol
Characteristic
70
TSSL2SCH,
TSSL2SCL
SS ↓ to SCK ↓ or SCK ↑ Input
71
TSCH
SCK Input High Time
(Slave mode)
SCK Input Low Time
(Slave mode)
71A
72
TSCL
72A
Min
Max Units
TCY
—
ns
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
100
—
ns
1.5 TCY + 40
—
ns
100
—
ns
73
TDIV2SCH,
TDIV2SCL
Setup Time of SDI Data Input to SCK Edge
73A
TB2B
Last Clock Edge of Byte 1 to the 1st Clock Edge
of Byte 2
74
TSCH2DIL,
TSCL2DIL
Hold Time of SDI Data Input to SCK Edge
75
TDOR
SDO Data Output Rise Time
—
25
ns
76
TDOF
SDO Data Output Fall Time
—
25
ns
78
TSCR
SCK Output Rise Time (Master mode)
—
25
ns
79
TSCF
SCK Output Fall Time (Master mode)
80
TSCH2DOV, SDO Data Output Valid after SCK Edge
TSCL2DOV
Note 1:
2:
—
25
ns
—
50
ns
Conditions
(Note 1)
(Note 1)
(Note 2)
Requires the use of Parameter #73A.
Only if Parameter #71A and #72A are used.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 373
PIC18F85J90 FAMILY
FIGURE 25-10:
EXAMPLE SPI MASTER MODE TIMING (CKE = 1)
SS
81
SCK
(CKP = 0)
71
72
79
73
SCK
(CKP = 1)
80
78
MSb
SDO
bit 6 - - - - - - 1
LSb
bit 6 - - - - 1
LSb In
75, 76
SDI
MSb In
74
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-15: EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 1)
Param.
No.
71
Symbol
TSCH
71A
72
TSCL
72A
Characteristic
Min
Max Units
SCK Input High Time
(Slave mode)
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
SCK Input Low Time
(Slave mode)
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
100
—
ns
1.5 TCY + 40
—
ns
100
—
ns
73
TDIV2SCH,
TDIV2SCL
Setup Time of SDI Data Input to SCK Edge
73A
TB2B
Last Clock Edge of Byte 1 to the 1st Clock Edge
of Byte 2
74
TSCH2DIL,
TSCL2DIL
Hold Time of SDI Data Input to SCK Edge
75
TDOR
SDO Data Output Rise Time
—
25
ns
76
TDOF
SDO Data Output Fall Time
—
25
ns
78
TSCR
SCK Output Rise Time (Master mode)
—
25
ns
79
TSCF
SCK Output Fall Time (Master mode)
80
TSCH2DOV, SDO Data Output Valid after SCK Edge
TSCL2DOV
81
TDOV2SCH, SDO Data Output Setup to SCK Edge
TDOV2SCL
Note 1:
2:
—
25
ns
—
50
ns
TCY
—
ns
Conditions
(Note 1)
(Note 1)
(Note 2)
Requires the use of Parameter #73A.
Only if Parameter #71A and #72A are used.
DS39770B-page 374
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
FIGURE 25-11:
EXAMPLE SPI SLAVE MODE TIMING (CKE = 0)
SS
70
SCK
(CKP = 0)
83
71
72
78
79
79
78
SCK
(CKP = 1)
80
MSb
SDO
bit 6 - - - - - - 1
LSb
75, 76
MSb In
SDI
77
bit 6 - - - - 1
LSb In
74
73
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-16: EXAMPLE SPI MODE REQUIREMENTS (SLAVE MODE TIMING, CKE = 0)
Param
No.
Symbol
Characteristic
70
TSSL2SCH, SS ↓ to SCK ↓ or SCK ↑ Input
TSSL2SCL
70A
TSSL2WB SS to write to SSPBUF
71
TSCH
SCK Input High Time
(Slave mode)
71A
72
TSCL
72A
SCK Input Low Time
(Slave mode)
Min
3 TCY
Max Units Conditions
—
ns
3 TCY
—
ns
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
100
—
ns
—
ns
—
ns
73
TDIV2SCH, Setup Time of SDI Data Input to SCK Edge
TDIV2SCL
73A
TB2B
74
TSCH2DIL, Hold Time of SDI Data Input to SCK Edge
TSCL2DIL
75
TDOR
SDO Data Output Rise Time
—
25
ns
76
TDOF
SDO Data Output Fall Time
—
25
ns
77
TSSH2DOZ SS ↑ to SDO Output High-impedance
10
50
ns
78
TSCR
SCK Output Rise Time (Master mode)
—
25
ns
79
TSCF
SCK Output Fall Time (Master mode)
—
25
ns
80
TSCH2DOV, SDO Data Output Valid after SCK Edge
TSCL2DOV
—
50
ns
83
TSCH2SSH, SS ↑ after SCK Edge
TSCL2SSH
1.5 TCY + 40
—
ns
Note 1:
2:
Last Clock Edge of Byte 1 to the First Clock Edge of Byte 2 1.5 TCY + 40
100
(Note 1)
(Note 1)
(Note 2)
Requires the use of Parameter #73A.
Only if Parameter #71A and #72A are used.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 375
PIC18F85J90 FAMILY
FIGURE 25-12:
EXAMPLE SPI SLAVE MODE TIMING (CKE = 1)
82
SS
SCK
(CKP = 0)
70
83
71
72
SCK
(CKP = 1)
80
MSb
SDO
bit 6 - - - - - - 1
LSb
75, 76
SDI
MSb In
77
bit 6 - - - - 1
LSb In
74
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-17: EXAMPLE SPI SLAVE MODE REQUIREMENTS (CKE = 1)
Param
No.
Symbol
Characteristic
Min
Max Units Conditions
70
TSSL2SCH, SS ↓ to SCK ↓ or SCK ↑ Input
TSSL2SCL
70A
TSSL2WB
SS to write to SSPBUF
71
TSCH
SCK Input High Time
(Slave mode)
TSCL
SCK Input Low Time
(Slave mode)
73A
TB2B
Last Clock Edge of Byte 1 to the First Clock Edge of Byte 2 1.5 TCY + 40
74
TSCH2DIL, Hold Time of SDI Data Input to SCK Edge
TSCL2DIL
71A
72
72A
3 TCY
—
ns
3 TCY
—
ns
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
(Note 1)
—
ns
(Note 2)
—
ns
Continuous
100
75
TDOR
SDO Data Output Rise Time
—
25
ns
76
TDOF
SDO Data Output Fall Time
—
25
ns
77
TSSH2DOZ SS ↑ to SDO Output High-Impedance
10
50
ns
78
TSCR
SCK Output Rise Time (Master mode)
—
25
ns
79
TSCF
SCK Output Fall Time (Master mode)
—
25
ns
80
TSCH2DOV, SDO Data Output Valid after SCK Edge
TSCL2DOV
—
50
ns
82
TSSL2DOV SDO Data Output Valid after SS ↓ Edge
—
50
ns
83
TSCH2SSH, SS ↑ after SCK Edge
TSCL2SSH
1.5 TCY + 40
—
ns
Note 1:
2:
(Note 1)
Requires the use of Parameter #73A.
Only if Parameter #71A and #72A are used.
DS39770B-page 376
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
I2C™ BUS START/STOP BITS TIMING
FIGURE 25-13:
SCL
91
93
90
92
SDA
Stop
Condition
Start
Condition
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-18: I2C™ BUS START/STOP BITS REQUIREMENTS (SLAVE MODE)
Param.
Symbol
No.
90
91
92
93
TSU:STA
THD:STA
TSU:STO
Characteristic
Min
Max
Units
Conditions
ns
Only relevant for Repeated
Start condition
ns
After this period, the first
clock pulse is generated
Start Condition
100 kHz mode
4700
—
Setup Time
400 kHz mode
600
—
Start Condition
100 kHz mode
4000
—
Hold Time
400 kHz mode
600
—
Stop Condition
100 kHz mode
4700
—
Setup Time
400 kHz mode
600
—
100 kHz mode
4000
—
400 kHz mode
600
—
THD:STO Stop Condition
Hold Time
© 2007 Microchip Technology Inc.
Preliminary
ns
ns
DS39770B-page 377
PIC18F85J90 FAMILY
FIGURE 25-14:
I2C™ BUS DATA TIMING
103
102
100
101
SCL
90
106
107
91
92
SDA
In
110
109
109
SDA
Out
Note:
Refer to Figure 25-3 for load conditions.
DS39770B-page 378
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 25-19: I2C™ BUS DATA REQUIREMENTS (SLAVE MODE)
Param.
No.
100
Symbol
THIGH
101
TLOW
102
TR
103
TF
TSU:STA
90
THD:STA
91
THD:DAT
106
TSU:DAT
107
TSU:STO
92
109
TAA
110
TBUF
D102
CB
Note 1:
2:
Characteristic
Clock High Time
Clock Low Time
SDA and SCL Rise Time
SDA and SCL Fall Time
Min
Max
Units
100 kHz mode
4.0
—
μs
400 kHz mode
0.6
—
μs
MSSP Module
1.5 TCY
—
100 kHz mode
4.7
—
μs
μs
400 kHz mode
1.3
—
MSSP Module
1.5 TCY
—
100 kHz mode
—
1000
ns
400 kHz mode
20 + 0.1 CB
300
ns
Conditions
CB is specified to be from
10 to 400 pF
100 kHz mode
—
300
ns
400 kHz mode
20 + 0.1 CB
300
ns
CB is specified to be from
10 to 400 pF
Start Condition Setup Time 100 kHz mode
4.7
—
μs
400 kHz mode
0.6
—
μs
Only relevant for Repeated
Start condition
Start Condition Hold Time
Data Input Hold Time
Data Input Setup Time
100 kHz mode
4.0
—
μs
400 kHz mode
0.6
—
μs
100 kHz mode
0
—
ns
400 kHz mode
0
0.9
μs
100 kHz mode
250
—
ns
400 kHz mode
100
—
ns
Stop Condition Setup Time 100 kHz mode
4.7
—
μs
400 kHz mode
0.6
—
μs
Output Valid from Clock
Bus Free Time
Bus Capacitive Loading
100 kHz mode
—
3500
ns
400 kHz mode
—
—
ns
100 kHz mode
4.7
—
μs
400 kHz mode
1.3
—
μs
—
400
pF
After this period, the first clock
pulse is generated
(Note 2)
(Note 1)
Time the bus must be free before
a new transmission can start
As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of
the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
A Fast mode I2C™ bus device can be used in a Standard mode I2C bus system, but the requirement, TSU:DAT ≥ 250 ns,
must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If
such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line,
TR max. + TSU:DAT = 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification), before the SCL line
is released.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 379
PIC18F85J90 FAMILY
MSSP I2C™ BUS START/STOP BITS TIMING WAVEFORMS
FIGURE 25-15:
SCL
93
91
90
92
SDA
Stop
Condition
Start
Condition
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-20: MSSP I2C™ BUS START/STOP BITS REQUIREMENTS
Param.
Symbol
No.
90
TSU:STA
Characteristic
After this period, the
first clock pulse is
generated
400 kHz mode
2(TOSC)(BRG + 1)
—
mode(1)
2(TOSC)(BRG + 1)
—
100 kHz mode
2(TOSC)(BRG + 1)
—
400 kHz mode
2(TOSC)(BRG + 1)
—
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
Stop Condition
100 kHz mode
2(TOSC)(BRG + 1)
—
Setup Time
400 kHz mode
THD:STO Stop Condition
2(TOSC)(BRG + 1)
—
mode(1)
2(TOSC)(BRG + 1)
—
100 kHz mode
2(TOSC)(BRG + 1)
—
400 kHz mode
2(TOSC)(BRG + 1)
—
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
2C™
Maximum pin capacitance = 10 pF for all I
FIGURE 25-16:
ns
Setup Time
Hold Time
Note 1:
Only relevant for
Repeated Start
condition
—
1 MHz
93
ns
2(TOSC)(BRG + 1)
Hold Time
92
Units
100 kHz mode
THD:STA Start Condition
TSU:STO
Max
Start Condition
1 MHz
91
Min
Conditions
ns
ns
pins.
MSSP I2C™ BUS DATA TIMING
103
102
100
101
SCL
90
106
91
107
92
SDA
In
109
109
110
SDA
Out
Note:
DS39770B-page 380
Refer to Figure 25-3 for load conditions.
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 25-21: MSSP I2C™ BUS DATA REQUIREMENTS
Param.
Symbol
No.
100
101
THIGH
TLOW
Characteristic
Min
Max
Units
100 kHz mode
2(TOSC)(BRG + 1)
—
ms
400 kHz mode
2(TOSC)(BRG + 1)
—
ms
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
ms
Clock Low Time 100 kHz mode
2(TOSC)(BRG + 1)
—
ms
400 kHz mode
2(TOSC)(BRG + 1)
—
ms
(1)
Clock High
Time
2(TOSC)(BRG + 1)
—
ms
100 kHz mode
—
1000
ns
400 kHz mode
20 + 0.1 CB
300
ns
1 MHz mode(1)
—
300
ns
100 kHz mode
—
300
ns
400 kHz mode
20 + 0.1 CB
300
ns
1 MHz mode(1)
—
100
ns
100 kHz mode
2(TOSC)(BRG + 1)
—
ms
400 kHz mode
2(TOSC)(BRG + 1)
—
ms
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
ms
1 MHz mode
102
103
90
91
106
107
92
109
TR
TF
TSU:STA
SDA and SCL
Rise Time
SDA and SCL
Fall Time
Start Condition
Setup Time
THD:STA Start Condition
Hold Time
THD:DAT Data Input
Hold Time
TSU:DAT
Data Input
Setup Time
TSU:STO Stop Condition
Setup Time
TAA
Output Valid
from Clock
100 kHz mode
2(TOSC)(BRG + 1)
—
ms
400 kHz mode
2(TOSC)(BRG + 1)
—
ms
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
ms
100 kHz mode
0
—
ns
400 kHz mode
0
0.9
ms
1 MHz mode(1)
TBD
—
ns
100 kHz mode
250
—
ns
400 kHz mode
100
—
ns
1 MHz mode(1)
TBD
—
ns
100 kHz mode
2(TOSC)(BRG + 1)
—
ms
400 kHz mode
2(TOSC)(BRG + 1)
—
ms
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
ms
100 kHz mode
—
3500
ns
400 kHz mode
—
1000
ns
(1)
—
—
ns
100 kHz mode
4.7
—
ms
1 MHz mode
110
D102
TBUF
CB
Bus Free Time
400 kHz mode
1.3
—
ms
1 MHz mode(1)
TBD
—
ms
—
400
pF
Bus Capacitive Loading
Conditions
CB is specified to be from
10 to 400 pF
CB is specified to be from
10 to 400 pF
Only relevant for Repeated
Start condition
After this period, the first
clock pulse is generated
(Note 2)
Time the bus must be free
before a new transmission
can start
Legend: TBD = To Be Determined
Note 1: Maximum pin capacitance = 10 pF for all I2C™ pins.
2: A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but parameter #107 ≥ 250 ns
must then be met. This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit
to the SDA line, parameter #102 + parameter #107 = 1000 + 250 = 1250 ns (for 100 kHz mode), before the
SCL line is released.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 381
PIC18F85J90 FAMILY
FIGURE 25-17:
EUSART/AUSART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
TXx/CKx
pin
121
121
RXx/DTx
pin
120
Note:
122
Refer to Figure 25-3 for load conditions.
TABLE 25-22: EUSART/AUSART SYNCHRONOUS TRANSMISSION REQUIREMENTS
Param
No.
120
Symbol
Characteristic
TCKH2DTV SYNC XMIT (MASTER and SLAVE)
Clock High to Data Out Valid
Min
Max
Units
—
40
ns
121
TCKRF
Clock Out Rise Time and Fall Time (Master mode)
—
20
ns
122
TDTRF
Data Out Rise Time and Fall Time
—
20
ns
FIGURE 25-18:
Conditions
EUSART/AUSART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
TXx/CKx
pin
125
RXx/DTx
pin
126
Note:
Refer to Figure 25-3 for load conditions.
TABLE 25-23: EUSART/AUSART SYNCHRONOUS RECEIVE REQUIREMENTS
Param.
No.
Symbol
Characteristic
125
TDTV2CKL SYNC RCV (MASTER and SLAVE)
Data Hold before CKx ↓ (DTx hold time)
126
TCKL2DTL
DS39770B-page 382
Data Hold after CKx ↓ (DTx hold time)
Preliminary
Min
Max
Units
10
—
ns
15
—
ns
Conditions
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
TABLE 25-24: A/D CONVERTER CHARACTERISTICS: PIC18F85J90 FAMILY (INDUSTRIAL)
Param
Symbol
No.
Characteristic
Min
Typ
Max
Units
—
—
10
bits
Conditions
A01
NR
Resolution
A03
EIL
Integral Linearity Error
—
—
<±1
LSb ΔVREF ≥ 3.0V
A04
EDL
Differential Linearity Error
—
—
<±1
LSb ΔVREF ≥ 3.0V
A06
EOFF
Offset Error
—
—
<±3
LSb ΔVREF ≥ 3.0V
A07
EGN
Gain Error
—
—
<±3
LSb ΔVREF ≥ 3.0V
A10
—
Monotonicity
—
VSS ≤ VAIN
A20
ΔVREF
Reference Voltage Range
(VREFH – VREFL)
2.0
3
—
—
—
—
V
V
VDD < 3.0V
VDD ≥ 3.0V
A21
VREFH
Reference Voltage High
VSS
—
VREFH
V
A22
VREFL
Reference Voltage Low
VSS – 0.3V
—
VDD – 3.0V
V
A25
VAIN
Analog Input Voltage
VREFL
—
VREFH
V
A30
ZAIN
Recommended Impedance of
Analog Voltage Source
—
—
2.5
kΩ
A50
IREF
VREF Input Current(2)
—
—
—
—
5
150
μA
μA
Note 1:
2:
Guaranteed(1)
≤
VREF
During VAIN acquisition.
During A/D conversion
cycle.
The A/D conversion result never decreases with an increase in the input voltage and has no missing codes.
VREFH current is from RA3/AN3/VREF+ pin or VDD, whichever is selected as the VREFH source.
VREFL current is from RA2/AN2/VREF- pin or VSS, whichever is selected as the VREFL source.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 383
PIC18F85J90 FAMILY
FIGURE 25-19:
A/D CONVERSION TIMING
BSF ADCON0, GO
(Note 2)
131
Q4
130
132
A/D CLK
9
A/D DATA
8
...
7
...
2
1
0
NEW_DATA
OLD_DATA
ADRES
TCY (Note 1)
ADIF
GO
DONE
SAMPLING STOPPED
SAMPLE
Note
1:
If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts.
This allows the SLEEP instruction to be executed.
2:
This is a minimal RC delay (typically 100 ns), which also disconnects the holding capacitor from the analog input.
TABLE 25-25: A/D CONVERSION REQUIREMENTS
Param
Symbol
No.
130
TAD
Characteristic
A/D Clock Period
Min
Max
Units
0.7
25.0(1)
μs
TOSC based, VREF ≥ 3.0V
TBD
1
μs
A/D RC mode
12
TAD
μs
131
TCNV
Conversion Time
(not including acquisition time)(2)
11
132
TACQ
Acquisition Time(3)
1.4
—
135
TSWC
Switching Time from Convert → Sample
—
(Note 4)
TBD
TDIS
Discharge Time
0.2
—
Legend:
Note 1:
2:
3:
4:
Conditions
-40°C to +85°C
μs
TBD = To Be Determined
The time of the A/D clock period is dependent on the device frequency and the TAD clock divider.
ADRES registers may be read on the following TCY cycle.
The time for the holding capacitor to acquire the “New” input voltage when the voltage changes full scale
after the conversion (VDD to VSS or VSS to VDD). The source impedance (RS) on the input channels is 50Ω.
On the following cycle of the device clock.
DS39770B-page 384
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
NOTES:
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 385
PIC18F85J90 FAMILY
26.0
DC AND AC
CHARACTERISTICS GRAPHS
AND TABLES
Graphs and tables are not available at this time.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 387
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 388
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
27.0
PACKAGING INFORMATION
27.1
Package Marking Information
64-Lead TQFP
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
18F65J90
-I/PT e3
0610017
80-Lead TQFP
Example
XXXXXXXXXXXX
XXXXXXXXXXXX
YYWWNNN
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
PIC18F85J90
-I/PT e3
0610017
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 389
PIC18F85J90 FAMILY
27.2
Package Details
The following sections give the technical details of the
packages.
64-Lead Plastic Thin Quad Flatpack (PT) – 10x10x1 mm Body, 2.00 mm Footprint [TQFP]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
D1
E
e
E1
N
b
NOTE 1
123
NOTE 2
α
A
c
φ
A2
β
A1
L
L1
Units
Dimension Limits
Number of Leads
MILLIMETERS
MIN
N
NOM
MAX
64
Lead Pitch
e
Overall Height
A
–
0.50 BSC
–
Molded Package Thickness
A2
0.95
1.00
1.05
Standoff
A1
0.05
–
0.15
Foot Length
L
0.45
0.60
0.75
Footprint
L1
1.20
1.00 REF
Foot Angle
φ
Overall Width
E
12.00 BSC
Overall Length
D
12.00 BSC
Molded Package Width
E1
10.00 BSC
Molded Package Length
D1
10.00 BSC
0°
3.5°
7°
Lead Thickness
c
0.09
–
0.20
Lead Width
b
0.17
0.22
0.27
Mold Draft Angle Top
α
11°
12°
13°
Mold Draft Angle Bottom
β
11°
12°
13°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Chamfers at corners are optional; size may vary.
3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-085B
DS39770B-page 390
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
80-Lead Plastic Thin Quad Flatpack (PT) – 12x12x1 mm Body, 2.00 mm Footprint [TQFP]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
D1
E
e
E1
N
b
NOTE 1
12 3
NOTE 2
c
β
φ
L
α
A
A2
A1
L1
Units
Dimension Limits
Number of Leads
MILLIMETERS
MIN
N
NOM
MAX
80
Lead Pitch
e
Overall Height
A
–
0.50 BSC
–
Molded Package Thickness
A2
0.95
1.00
1.05
Standoff
A1
0.05
–
0.15
Foot Length
L
0.45
0.60
0.75
Footprint
L1
1.20
1.00 REF
Foot Angle
φ
Overall Width
E
14.00 BSC
Overall Length
D
14.00 BSC
Molded Package Width
E1
12.00 BSC
Molded Package Length
D1
12.00 BSC
0°
3.5°
7°
Lead Thickness
c
0.09
–
0.20
Lead Width
b
0.17
0.22
0.27
Mold Draft Angle Top
α
11°
12°
13°
Mold Draft Angle Bottom
β
11°
12°
13°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Chamfers at corners are optional; size may vary.
3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-092B
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 391
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 392
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
APPENDIX A:
REVISION HISTORY
APPENDIX B:
Revision A (July 2006)
Original data sheet for PIC18F85J90 family devices.
Devices in the PIC18F85J90 and PIC18F8490 families
are very similar in their functions and feature sets.
However, there are some potentially important differences which should be considered when migrating an
application across device families to achieve a new
design goal. These are summarized in Table B-1. The
areas of difference, which could be a major impact on
migration, are discussed in greater detail later in this
section.
Revision B (March 2007)
Updated power-down and supply-current electrical
characteristics and package details illustrations.
TABLE B-1:
MIGRATION
BETWEEN HIGH-END
DEVICE FAMILIES
NOTABLE DIFFERENCES BETWEEN PIC18F8490 AND PIC18F85J90 FAMILIES
Characteristic
Operating Frequency
Supply Voltage
Operating Current
PIC18F85J90 Family
PIC18F8490 Family
40 MHz @ 2.15V
40 MHz @ 4.2V
2.0V-3.6V, Dual Voltage Requirement
2.0V-5.5V
Low
Lower
32 Kbytes
16 Kbytes
Program Memory Endurance
10,000 Write/Erase Cycles (typical)
100,000 Write/Erase Cycles (typical)
Program Memory Retention
20 Years (minimum)
40 Years (minimum)
Program Memory Size (maximum)
43.8 μs/byte (2.8 ms/64-byte block)
15.6 μs/byte (1 ms/64-byte block)
I/O Sink/Source at 25 mA
PORTB and PORTC Only
All Ports
Input Voltage Tolerance on I/O Pins
Programming Time (Normalized)
5.5V on Digital Only Pins
VDD on All I/O Pins
I/O
67
66
LCD Outputs (maximum pixels,
segments x commons)
192
192
4 Modes
1 Mode
Implemented; Includes Voltage Boost
Not Available
PORTB, PORTD, PORTE
and PORTJ
PORTB
Available on USARTs, SPI and CCP
Output Pins
Not Available
Limited Primary Options (EC, HS,
PLL); Flexible Internal Oscillator
(INTOSC and INTRC)
More Primary Options (EC, HS, XT,
LP, RC, PLL); Flexible Internal
Oscillator (INTOSC and INTRC)
LCD Bias Generation
LCD Voltage Regulator
Pull-ups
Open-Drain Output Option
Oscillator Options
Programming Entry
Low Voltage, Key Sequence
VPP and LVP
Code Protection
Single Block, All or Nothing
Multiple Code Protection Blocks
Stored in Last 4 Words of
Program Memory space
Stored in Configuration Space,
Starting at 300000h
Configuration Words
200 μs (typical)
Start-up Time from Sleep
10 μs (typical) with
Voltage Regulator Disabled
10 μs (typical)
Power-up Timer
Always on
Configurable
Data EEPROM
Use Self-Programming
Not Available
BOR
Simple BOR with Voltage Regulator
Separate Programmable BOR
LVD
Integrated with Voltage Regulator
Separate Programmable Module
A/D Channels
12
12
A/D Calibration
Self-Calibration Feature
Software Look-up Table
Not available
Available
In-Circuit Emulation
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 393
PIC18F85J90 FAMILY
B.1
Power Requirement Differences
The most significant difference between the
PIC18F85J90 and PIC18F8490 device families is the
power requirements. PIC18F85J90 family devices are
designed on a smaller process. This results in lower
maximum voltage and higher leakage current.
The operating voltage range for PIC18F85J90 devices
is 2.0V to 3.6V. In addition, these devices have split
power requirements: one for the core logic and one for
the I/O. One of the VDD pins is separated for the core
logic supply (VDDCORE). This pin has specific voltage
and capacitor requirements as described in
Section 25.0 “Electrical Characteristics”.
B.2
Oscillator Differences
PIC18F8490 and PIC18F85J90 family devices share a
similar range of oscillator options. The major difference
is that PIC18F85J90 family devices support a smaller
number of primary (external) oscillator options, namely
HS and EC Oscillator modes.
While both device families have an internal PLL that
can be used with the primary oscillators, the PLL for the
PIC18F85J90 family is not enabled as a device
configuration option. Instead, it must be enabled in
software.
The clocking differences should be considered when
making a conversion between the PIC18F8490 and
PIC18F85J90 device families.
B.3
LCD Module
When converting an LCD application between the
PIC18F85J90 and the PIC18F8490 families, the
following things must be considered:
• Available Segments: The module for
PIC18F65J90 devices supports 33 segments, as
opposed to 32 segments in PIC18F6490 devices.
(The 80-pin devices of both families support
48 segments. All devices support 4 commons.)
• Bias Generation: The PIC18F85J90 version of
the module also incorporates its own independent
voltage regulator, which supports 4 circuit configurations for bias generation, voltage boost to
support displays that operate above device VDD
and software contrast control.
DS39770B-page 394
• Additional LCD Function Pins: The
PIC18F85J90 family of devices adds 3 additional
LCD function pins in comparison to the
PIC18F8490 family. The additional pins are
associated with LCD bias generation:
- LCDBIAS0 (RG0)
- VLCAP1 (RG2)
- VLCPA2 (RG3)
• Segment Assignments: Eight of the LCD
segment functions have been relocated to different I/O pins than in PIC18F8490 devices. These
segments are listed in Table B-2.
• Other Considerations: In all LCD applications,
the connections of PIC18F85J90 devices to
external components for LCD bias generation are
different than PIC18F8490 devices. The addition
of the LCDBIAS0 output requires that this pin be
included in bias component configurations. A
more complete discussion is provided in
Section 15.3 “LCD Bias Generation”.
The simultaneous use of the external Timer1
oscillator and Segment 32 is not allowed in
PIC18F85J90 devices, since these functions are
shared on the same pin.
TABLE B-2:
LCD Segment
ASSIGNMENTS OF MOVED
LCD SEGMENTS
PIC18F8490
PIC18F85J90
SEG16
RA2
RC4
SEG17
RA3
RC3
SEG18
RF0
RA1
SEG27
RG3
RC6
SEG28
RG2
RC7
SEG29
RG0
RB5
SEG30
RG0
RB0
RJ0
RC1
SEG32
Note:
Preliminary
Refer to the pinout diagrams for pin
locations of I/O ports.
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
B.4
Pin Differences
B.5
Other Peripherals
Besides the LCD pinout differences already described,
there are other differences in the pinouts between the
PIC18F85J90 and the PIC18F8490 families:
Peripherals must also be considered when making a
conversion between the PIC18F85J90 and the
PIC18F8490 families:
• Input voltage tolerance
• Output current capabilities
• Available I/O
• A/D Converter: The converter for PIC18F85J90
devices require a calibration step prior to normal
operation.
• Data EEPROM: PIC18F85J90 devices do not
have this module but offer self-programming
capability.
• BOR: PIC18F85J90 devices do not have a
programmable BOR. Simple brown-out capability
is provided through the use of the internal voltage
regulator.
• LVD: PIC18F85J90 devices do not have this
module. A limited, fixed setpoint capability is
provided through the use of the internal voltage
regulator.
Pins on the PIC18F85J90 that have digital only input
capability will tolerate voltages up to 5.5V, and are thus,
tolerant to voltages above VDD. Table 9-1 in
Section 9.1 “I/O Port Pin Capabilities” contains the
complete list.
In addition to input differences, there are output differences as well. PIC18F85J90 devices have three
classes of pin output current capability: high, medium
and low. Not all I/O pins can source or sink equal levels
of current. Only PORTB and PORTC support the
25 mA source/sink capability that is supported by all
output pins on the PIC18F8490. Table 9-1 in
Section 9.1 “I/O Port Pin Capabilities” contains the
complete list of output capabilities.
Finally, the pins associated with the CCP,
EUSART/AUSART and SPI peripherals can be configured by the user as open-drain outputs. This allows for
simpler interfacing with external devices operating at
higher voltages. This capability is not directly
equivalent to any feature on the PIC18F8490 family.
There are also differences in the implementation of
some ports on PIC18F85J90 devices. While the total
number of general purpose I/O pins are very similar
(67 vs. 66), the implementation of individual pins has
notable differences:
• The MCLR pin is dedicated only to MCLR and
cannot be configured as an input (RG5) as it can
on PIC18F8490 devices.
• RF0 does not exist on PIC18F85J90 devices.
• RE0, RE1 and RE3 are implemented on
PIC18F85J90 devices, but not PIC18F8490
devices.
All of these pin differences (including power pin
differences) should be accounted for when making a
conversion between PIC18F8490 and PIC18F85J90
devices.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 395
PIC18F85J90 FAMILY
NOTES:
DS39770B-page 396
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
INDEX
A
A/D ................................................................................... 263
A/D Converter Interrupt, Configuring ....................... 267
Acquisition Requirements ........................................ 268
ADCAL Bit ................................................................ 271
ADCON0 Register .................................................... 263
ADCON1 Register .................................................... 263
ADCON2 Register .................................................... 263
ADRESH Register ............................................ 263, 266
ADRESL Register .................................................... 263
Analog Port Pins, Configuring .................................. 269
Associated Registers ............................................... 271
Automatic Acquisition Time ...................................... 269
Calibration ................................................................ 271
Configuring the Module ............................................ 267
Conversion Clock (TAD) ........................................... 269
Conversion Requirements ....................................... 385
Conversion Status (GO/DONE Bit) .......................... 266
Conversions ............................................................. 270
Converter Characteristics ........................................ 384
Operation in Power-Managed Modes ...................... 271
Special Event Trigger (CCP) .................................... 270
Use of the CCP2 Trigger .......................................... 270
Absolute Maximum Ratings ............................................. 349
AC (Timing) Characteristics ............................................. 366
Load Conditions for Device Timing Specifications ... 367
Parameter Symbology ............................................. 366
Temperature and Voltage Specifications ................. 367
Timing Conditions .................................................... 367
ACKSTAT ........................................................................ 219
ACKSTAT Status Flag ..................................................... 219
ADCAL Bit ........................................................................ 271
ADCON0 Register ............................................................ 263
GO/DONE Bit ........................................................... 266
ADCON1 Register ............................................................ 263
ADCON2 Register ............................................................ 263
ADDFSR .......................................................................... 338
ADDLW ............................................................................ 301
Addressable Universal Synchronous Asynchronous Receiver
Transmitter (AUSART). See AUSART.
ADDULNK ........................................................................ 338
ADDWF ............................................................................ 301
ADDWFC ......................................................................... 302
ADRESH Register ............................................................ 263
ADRESL Register .................................................... 263, 266
Analog-to-Digital Converter. See A/D.
ANDLW ............................................................................ 302
ANDWF ............................................................................ 303
Assembler
MPASM Assembler .................................................. 346
© 2007 Microchip Technology Inc.
AUSART
Asynchronous Mode ................................................ 254
Associated Registers, Receive ........................ 257
Associated Registers, Transmit ....................... 255
Receiver .......................................................... 256
Setting up 9-Bit Mode with Address Detect ..... 256
Transmitter ...................................................... 254
Baud Rate Generator (BRG) ................................... 252
Associated Registers ....................................... 252
Baud Rate Error, Calculating ........................... 252
Baud Rates, Asynchronous Modes ................. 253
High Baud Rate Select (BRGH Bit) ................. 252
Operation in Power-Managed Modes .............. 252
Sampling ......................................................... 252
Synchronous Master Mode ...................................... 258
Associated Registers, Receive ........................ 260
Associated Registers, Transmit ....................... 259
Reception ........................................................ 260
Transmission ................................................... 258
Synchronous Slave Mode ........................................ 261
Associated Registers, Receive ........................ 262
Associated Registers, Transmit ....................... 261
Reception ........................................................ 262
Transmission ................................................... 261
Auto-Wake-up on Sync Break Character ......................... 242
B
Baud Rate Generator ...................................................... 215
BC .................................................................................... 303
BCF ................................................................................. 304
BF .................................................................................... 219
BF Status Flag ................................................................. 219
Bias Generation (LCD)
Charge Pump Design Considerations ..................... 167
Block Diagrams
A/D ........................................................................... 266
Analog Input Model .................................................. 267
AUSART Receive .................................................... 256
AUSART Transmit ................................................... 254
Baud Rate Generator .............................................. 215
Capture Mode Operation ......................................... 150
Comparator Analog Input Model .............................. 277
Comparator I/O Operating Modes ........................... 274
Comparator Output .................................................. 276
Comparator Voltage Reference ............................... 280
Comparator Voltage Reference Output Buffer Example
281
Compare Mode Operation ....................................... 151
Connections for On-Chip Voltage Regulator ........... 290
Device Clock .............................................................. 29
EUSART Receive .................................................... 240
EUSART Transmit ................................................... 238
External Power-on Reset Circuit (Slow VDD Power-up)
47
Fail-Safe Clock Monitor ........................................... 292
Generic I/O Port Operation ...................................... 109
Interrupt Logic ............................................................ 94
LCD Clock Generation ............................................. 162
LCD Driver Module .................................................. 157
LCD Regulator Connections (M0 and M1) .............. 164
MSSP (I2C Master Mode) ........................................ 213
MSSP (I2C Mode) .................................................... 194
MSSP (SPI Mode) ................................................... 185
On-Chip Reset Circuit ................................................ 45
PIC18F6XJ90 ............................................................ 10
PIC18F8XJ90 ............................................................ 11
Preliminary
DS39770B-page 397
PIC18F85J90 FAMILY
PLL ............................................................................. 34
PWM Operation (Simplified) .................................... 153
Reads from Flash Program Memory .......................... 85
Resistor Ladder Configurations for M2 .................... 165
Resistor Ladder Configurations for M3 .................... 166
Single Comparator ................................................... 275
Table Read Operation ................................................ 81
Table Write Operation ................................................ 82
Table Writes to Flash Program Memory .................... 87
Timer0 in 16-Bit Mode .............................................. 132
Timer0 in 8-Bit Mode ................................................ 132
Timer1 (16-Bit Read/Write Mode) ............................ 136
Timer1 (8-Bit Mode) ................................................. 136
Timer2 ...................................................................... 142
Timer3 (16-Bit Read/Write Mode) ............................ 144
Timer3 (8-Bit Mode) ................................................. 144
Watchdog Timer ....................................................... 289
BN .................................................................................... 304
BNC .................................................................................. 305
BNN .................................................................................. 305
BNOV ............................................................................... 306
BNZ .................................................................................. 306
BOR. See Brown-out Reset.
BOV .................................................................................. 309
BRA .................................................................................. 307
Break Character (12-Bit) Transmit and Receive .............. 243
BRG. See Baud Rate Generator.
BRGH Bit
TXSTA1 Register ..................................................... 233
TXSTA2 Register ..................................................... 252
Brown-out Reset (BOR) ..................................................... 47
and On-Chip Voltage Regulator ............................... 291
Detecting .................................................................... 47
BSF .................................................................................. 307
BTFSC ............................................................................. 308
BTFSS .............................................................................. 308
BTG .................................................................................. 309
BZ ..................................................................................... 310
C
C Compilers
MPLAB C18 ............................................................. 346
MPLAB C30 ............................................................. 346
Calibration (A/D Converter) .............................................. 271
CALL ................................................................................ 310
CALLW ............................................................................. 339
Capture (CCP Module) ..................................................... 150
Associated Registers ............................................... 152
CCP Pin Configuration ............................................. 150
CCPR2H:CCPR2L Registers ................................... 150
Software Interrupt .................................................... 150
Timer1/Timer3 Mode Selection ................................ 150
Capture/Compare/PWM (CCP) ........................................ 147
Capture Mode. See Capture.
CCP Mode and Timer Resources ............................ 148
CCPRxH Register .................................................... 148
CCPRxL Register ..................................................... 148
Compare Mode. See Compare.
Configuration ............................................................ 148
Interaction of CCP1 and CCP2 for Timer Resources ....
149
Interconnect Configurations ..................................... 148
Clock Sources .................................................................... 31
Default System Clock on Reset ................................. 32
Selection Using OSCCON Register ........................... 32
CLRF ................................................................................ 311
DS39770B-page 398
CLRWDT ......................................................................... 311
Code Examples
16 x 16 Signed Multiply Routine ................................ 92
16 x 16 Unsigned Multiply Routine ............................ 92
8 x 8 Signed Multiply Routine .................................... 91
8 x 8 Unsigned Multiply Routine ................................ 91
Changing Between Capture Prescalers ................... 150
Computed GOTO Using an Offset Value ................... 61
Erasing a Flash Program Memory Row ..................... 86
Fast Register Stack ................................................... 61
How to Clear RAM (Bank 1) Using Indirect Addressing
74
Implementing a Real-Time Clock Using a Timer1 Interrupt Service ..................................................... 139
Initializing PORTA .................................................... 110
Initializing PORTB .................................................... 112
Initializing PORTC ................................................... 115
Initializing PORTD ................................................... 118
Initializing PORTE .................................................... 120
Initializing PORTF .................................................... 122
Initializing PORTG ................................................... 125
Initializing PORTH ................................................... 127
Initializing PORTJ .................................................... 129
Loading the SSPBUF (SSPSR) Register ................. 188
Reading a Flash Program Memory Word .................. 85
Saving STATUS, WREG and BSR Registers in RAM ...
108
Writing to Flash Program Memory ............................. 88
Code Protection ............................................................... 283
COMF .............................................................................. 312
Comparator ...................................................................... 273
Analog Input Connection Considerations ................ 277
Associated Registers ............................................... 277
Configuration ........................................................... 274
Effects of a Reset .................................................... 276
Interrupts ................................................................. 276
Operation ................................................................. 275
Operation During Sleep ........................................... 276
Outputs .................................................................... 275
Reference ................................................................ 275
External Signal ................................................ 275
Internal Signal .................................................. 275
Response Time ........................................................ 275
Comparator Specifications ............................................... 364
Comparator Voltage Reference ....................................... 279
Accuracy and Error .................................................. 280
Associated Registers ............................................... 281
Configuring .............................................................. 279
Connection Considerations ...................................... 280
Effects of a Reset .................................................... 280
Operation During Sleep ........................................... 280
Compare (CCP Module) .................................................. 151
Associated Registers ............................................... 152
CCP Pin Configuration ............................................. 151
CCPR2 Register ...................................................... 151
Software Interrupt .................................................... 151
Special Event Trigger .............................. 145, 151, 270
Timer1/Timer3 Mode Selection ................................ 151
Computed GOTO ............................................................... 61
Configuration Bits ............................................................ 283
Configuration Register Protection .................................... 294
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
Core Features
Easy Migration ............................................................. 7
Extended Instruction Set .............................................. 7
Memory Options ........................................................... 7
nanoWatt Technology .................................................. 7
Oscillator Options and Features .................................. 7
CPFSEQ .......................................................................... 312
CPFSGT .......................................................................... 313
CPFSLT ........................................................................... 313
Crystal Oscillator/Ceramic Resonator ................................ 33
Customer Change Notification Service ............................ 407
Customer Notification Service .......................................... 407
Customer Support ............................................................ 407
D
Data Addressing Modes ..................................................... 74
Comparing Addressing Modes with the Extended Instruction Set Enabled ......................................... 78
Direct .......................................................................... 74
Indexed Literal Offset ................................................. 77
BSR ................................................................... 79
Instructions Affected .......................................... 77
Mapping Access Bank ....................................... 79
Indirect ....................................................................... 74
Inherent and Literal .................................................... 74
Data Memory ..................................................................... 64
Access Bank .............................................................. 67
Bank Select Register (BSR) ....................................... 64
Extended Instruction Set ............................................ 77
General Purpose Registers ........................................ 67
Memory Maps
PIC18FX3J90/X4J90 Devices ........................... 65
PIC18FX5J90 Devices ....................................... 66
Special Function Registers ................................ 68
Special Function Registers ........................................ 68
DAW ................................................................................. 314
DC and AC Characteristics
Graphs and Tables .................................................. 387
DC Characteristics ........................................................... 361
Power-Down and Supply Current ............................ 352
Supply Voltage ......................................................... 351
DCFSNZ .......................................................................... 315
DECF ............................................................................... 314
DECFSZ ........................................................................... 315
Default System Clock ......................................................... 32
Details on Individual Family Members ................................. 8
Development Support ...................................................... 345
Device Overview .................................................................. 7
Features (64-Pin Devices) ........................................... 9
Features (80-Pin Devices) ........................................... 9
Direct Addressing ............................................................... 75
E
Effect on Standard PIC18 Instructions ............................. 342
Effects of Power-Managed Modes on Various Clock Sources
36
Electrical Characteristics .................................................. 349
Enhanced Universal Synchronous Asynchronous Receiver
Transmitter (EUSART). See EUSART.
ENVREG Pin .................................................................... 290
Equations
A/D Acquisition Time ................................................ 268
A/D Minimum Charging Time ................................... 268
Calculating the Minimum Required Acquisition Time .....
268
LCD Static and Dynamic Current ............................. 167
© 2007 Microchip Technology Inc.
Errata ................................................................................... 5
EUSART
Asynchronous Mode ................................................ 238
12-Bit Break Transmit and Receive ................. 243
Associated Registers, Receive ........................ 241
Associated Registers, Transmit ....................... 239
Auto-Wake-up on Sync Break ......................... 242
Receiver .......................................................... 240
Setting up 9-Bit Mode with Address Detect ..... 240
Transmitter ...................................................... 238
Baud Rate Generator (BRG) ................................... 233
Associated Registers ....................................... 233
Auto-Baud Rate Detect .................................... 236
Baud Rate Error, Calculating ........................... 233
Baud Rates, Asynchronous Modes ................. 234
High Baud Rate Select (BRGH Bit) ................. 233
Operation in Power-Managed Modes .............. 233
Sampling ......................................................... 233
Synchronous Master Mode ...................................... 244
Associated Registers, Receive ........................ 246
Associated Registers, Transmit ....................... 245
Reception ........................................................ 246
Transmission ................................................... 244
Synchronous Slave Mode ........................................ 247
Associated Registers, Receive ........................ 248
Associated Registers, Transmit ....................... 247
Reception ........................................................ 248
Transmission ................................................... 247
Extended Instruction Set
ADDFSR .................................................................. 338
ADDULNK ............................................................... 338
CALLW .................................................................... 339
MOVSF .................................................................... 339
MOVSS .................................................................... 340
PUSHL ..................................................................... 340
SUBFSR .................................................................. 341
SUBULNK ................................................................ 341
External Oscillator Modes .................................................. 33
EC Modes .................................................................. 34
HS Modes .................................................................. 33
F
Fail-Safe Clock Monitor ........................................... 283, 292
Exiting Fail-Safe Operation ...................................... 293
Interrupts in Power-Managed Modes ...................... 293
POR or Wake-up from Sleep ................................... 293
WDT During Oscillator Failure ................................. 292
Fast Register Stack ........................................................... 61
Firmware Instructions ...................................................... 295
Flash Configuration Words .............................................. 283
Flash Program Memory ..................................................... 81
Associated Registers ................................................. 89
Control Registers ....................................................... 82
EECON1 and EECON2 ..................................... 82
TABLAT (Table Latch) Register ........................ 84
TBLPTR (Table Pointer) Register ...................... 84
Erase Sequence ........................................................ 86
Erasing ...................................................................... 86
Operation During Code-Protect ................................. 89
Reading ..................................................................... 85
Table Pointer
Boundaries Based on Operation ....................... 84
Table Pointer Boundaries .......................................... 84
Table Reads and Table Writes .................................. 81
Write Sequence ......................................................... 87
Writing ....................................................................... 87
Preliminary
DS39770B-page 399
PIC18F85J90 FAMILY
Unexpected Termination .................................... 89
Write Verify ........................................................ 89
FSCM. See Fail-Safe Clock Monitor.
G
GOTO ............................................................................... 316
H
Hardware Multiplier ............................................................ 91
Introduction ................................................................ 91
Operation ................................................................... 91
Performance Comparison .......................................... 91
I
I/O Ports ........................................................................... 109
Input Voltage Considerations ................................... 109
Open-Drain Outputs ................................................. 110
Output Pin Drive ....................................................... 109
Pin Capabilities ........................................................ 109
Pull-up Configuration ............................................... 110
I2C Mode (MSSP) ............................................................ 194
Acknowledge Sequence Timing ............................... 222
Associated Registers ............................................... 228
Baud Rate Generator ............................................... 215
Bus Collision
During a Repeated Start Condition .................. 226
During a Stop Condition ................................... 227
Clock Arbitration ....................................................... 216
Clock Stretching ....................................................... 208
10-Bit Slave Receive Mode (SEN = 1) ............. 208
10-Bit Slave Transmit Mode ............................. 208
7-Bit Slave Receive Mode (SEN = 1) ............... 208
7-Bit Slave Transmit Mode ............................... 208
Clock Synchronization and the CKP Bit ................... 209
Effects of a Reset ..................................................... 223
General Call Address Support ................................. 212
I2C Clock Rate w/BRG ............................................. 215
Master Mode ............................................................ 213
Baud Rate Generator ....................................... 215
Operation ......................................................... 214
Reception ......................................................... 219
Repeated Start Condition Timing ..................... 218
Start Condition Timing ..................................... 217
Transmission .................................................... 219
Multi-Master Communication, Bus Collision and Arbitration ................................................................... 223
Multi-Master Mode ................................................... 223
Operation ................................................................. 199
Read/Write Bit Information (R/W Bit) ............... 199, 201
Registers .................................................................. 194
Serial Clock (SCK/SCL) ........................................... 201
Slave Mode .............................................................. 199
Addressing ....................................................... 199
Addressing Masking ......................................... 200
Reception ......................................................... 201
Transmission .................................................... 201
Sleep Operation ....................................................... 223
Stop Condition Timing .............................................. 222
INCF ................................................................................. 316
INCFSZ ............................................................................ 317
In-Circuit Debugger .......................................................... 294
In-Circuit Serial Programming (ICSP) ...................... 283, 294
Indexed Literal Offset Addressing
and Standard PIC18 Instructions ............................. 342
Indexed Literal Offset Mode ............................................. 342
Indirect Addressing ............................................................ 75
DS39770B-page 400
INFSNZ ............................................................................ 317
Initialization Conditions for all Registers ...................... 51–53
Instruction Cycle ................................................................ 62
Clocking Scheme ....................................................... 62
Flow/Pipelining ........................................................... 62
Instruction Set .................................................................. 295
ADDLW .................................................................... 301
ADDWF .................................................................... 301
ADDWF (Indexed Literal Offset Mode) .................... 343
ADDWFC ................................................................. 302
ANDLW .................................................................... 302
ANDWF .................................................................... 303
BC ............................................................................ 303
BCF ......................................................................... 304
BN ............................................................................ 304
BNC ......................................................................... 305
BNN ......................................................................... 305
BNOV ...................................................................... 306
BNZ ......................................................................... 306
BOV ......................................................................... 309
BRA ......................................................................... 307
BSF .......................................................................... 307
BSF (Indexed Literal Offset Mode) .......................... 343
BTFSC ..................................................................... 308
BTFSS ..................................................................... 308
BTG ......................................................................... 309
BZ ............................................................................ 310
CALL ........................................................................ 310
CLRF ....................................................................... 311
CLRWDT ................................................................. 311
COMF ...................................................................... 312
CPFSEQ .................................................................. 312
CPFSGT .................................................................. 313
CPFSLT ................................................................... 313
DAW ........................................................................ 314
DCFSNZ .................................................................. 315
DECF ....................................................................... 314
DECFSZ .................................................................. 315
Extended Instructions .............................................. 337
Considerations when Enabling ........................ 342
Syntax .............................................................. 337
Use with MPLAB IDE Tools ............................. 344
General Format ........................................................ 297
GOTO ...................................................................... 316
INCF ........................................................................ 316
INCFSZ .................................................................... 317
INFSNZ .................................................................... 317
IORLW ..................................................................... 318
IORWF ..................................................................... 318
LFSR ....................................................................... 319
MOVF ...................................................................... 319
MOVFF .................................................................... 320
MOVLB .................................................................... 320
MOVLW ................................................................... 321
MOVWF ................................................................... 321
MULLW .................................................................... 322
MULWF .................................................................... 322
NEGF ....................................................................... 323
NOP ......................................................................... 323
Opcode Field Descriptions ....................................... 296
POP ......................................................................... 324
PUSH ....................................................................... 324
RCALL ..................................................................... 325
RESET ..................................................................... 325
RETFIE .................................................................... 326
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
RETLW .................................................................... 326
RETURN .................................................................. 327
RLCF ........................................................................ 327
RLNCF ..................................................................... 328
RRCF ....................................................................... 328
RRNCF .................................................................... 329
SETF ........................................................................ 329
SETF (Indexed Literal Offset Mode) ........................ 343
SLEEP ..................................................................... 330
Standard Instructions ............................................... 295
SUBFWB .................................................................. 330
SUBLW .................................................................... 331
SUBWF .................................................................... 331
SUBWFB .................................................................. 332
SWAPF .................................................................... 332
TBLRD ..................................................................... 333
TBLWT ..................................................................... 334
TSTFSZ ................................................................... 335
XORLW .................................................................... 335
XORWF .................................................................... 336
INTCON Register
RBIF Bit .................................................................... 112
INTCON Registers ............................................................. 95
Inter-Integrated Circuit. See I2C Mode.
Internal Oscillator Block ..................................................... 35
Adjustment ................................................................. 35
INTOSC Frequency Drift ............................................ 35
INTOSC Output Frequency ........................................ 35
OSC1, OSC2 Pin Configuration ................................. 35
Internal RC Oscillator
Use with WDT .......................................................... 289
Internal Voltage Regulator Specifications ........................ 364
Internet Address ............................................................... 407
Interrupt Sources ............................................................. 283
A/D Conversion Complete ....................................... 267
Capture Complete (CCP) ......................................... 150
Compare Complete (CCP) ....................................... 151
Interrupt-on-Change (RB7:RB4) .............................. 112
TMR0 Overflow ........................................................ 133
TMR1 Overflow ........................................................ 135
TMR2 to PR2 Match (PWM) .................................... 153
TMR3 Overflow ................................................ 143, 145
Interrupts ............................................................................ 93
During, Context Saving ............................................ 108
INTx Pin ................................................................... 108
PORTB, Interrupt-on-Change .................................. 108
TMR0 ....................................................................... 108
Interrupts, Flag Bits
Interrupt-on-Change (RB7:RB4) Flag (RBIF Bit) ..... 112
INTOSC, INTRC. See Internal Oscillator Block.
IORLW ............................................................................. 318
IORWF ............................................................................. 318
IPR Registers ................................................................... 104
L
LCD
Associated Registers ............................................... 183
Bias Generation ....................................................... 163
Bias Configurations .......................................... 164
M0 and M1 ............................................... 164
M2 ............................................................ 165
M3 ............................................................ 166
Bias Types ....................................................... 163
LCD Voltage Regulator .................................... 163
Charge Pump ................................................... 164, 167
Clock Source Selection ............................................ 162
© 2007 Microchip Technology Inc.
Configuring the Module ........................................... 182
Frame Frequency .................................................... 168
Interrupts ................................................................. 180
LCDCON Register ................................................... 158
LCDDATA Register ................................................. 158
LCDPS Register ...................................................... 158
LCDREG Register ................................................... 158
LCDSE Register ...................................................... 158
Multiplex Types ........................................................ 167
Operation During Sleep ........................................... 181
Pixel Control ............................................................ 167
Segment Enables .................................................... 167
Waveform Generation ............................................. 168
LCD Driver ........................................................................... 8
LCDCON Register ........................................................... 158
LCDDATA Register .......................................................... 158
LCDPS Register .............................................................. 158
LCDREG Register ........................................................... 158
LCDSE Register .............................................................. 158
LFSR ............................................................................... 319
Liquid Crystal Display (LCD) Driver ................................. 157
Low-Voltage Detection ..................................................... 290
M
Master Clear (MCLR) ......................................................... 47
Master Synchronous Serial Port (MSSP). See MSSP.
Memory Organization ........................................................ 57
Data Memory ............................................................. 64
Program Memory ....................................................... 57
Memory Programming Requirements .............................. 363
Microchip Internet Web Site ............................................. 407
MOVF .............................................................................. 319
MOVFF ............................................................................ 320
MOVLB ............................................................................ 320
MOVLW ........................................................................... 321
MOVSF ............................................................................ 339
MOVSS ............................................................................ 340
MOVWF ........................................................................... 321
MPLAB ASM30 Assembler, Linker, Librarian .................. 346
MPLAB ICD 2 In-Circuit Debugger .................................. 347
MPLAB ICE 2000 High-Performance Universal In-Circuit Emulator ........................................................................ 347
MPLAB Integrated Development Environment Software . 345
MPLAB PM3 Device Programmer ................................... 347
MPLAB REAL ICE In-Circuit Emulator System ............... 347
MPLINK Object Linker/MPLIB Object Librarian ............... 346
MSSP
ACK Pulse ....................................................... 199, 201
Control Registers (general) ..................................... 185
Module Overview ..................................................... 185
SPI Master/Slave Connection .................................. 189
SSPBUF Register .................................................... 190
SSPSR Register ...................................................... 190
MULLW ............................................................................ 322
MULWF ............................................................................ 322
N
NEGF ............................................................................... 323
NOP ................................................................................. 323
Notable Differences Between PIC18F8490 and PIC18F85J90
Families ................................................................... 393
LCD Module ............................................................. 394
Oscillator Options .................................................... 394
Other Peripherals .................................................... 395
Pin Differences ........................................................ 395
Power Requirements ............................................... 394
Preliminary
DS39770B-page 401
PIC18F85J90 FAMILY
O
Oscillator Configuration ...................................................... 29
EC .............................................................................. 29
ECPLL ........................................................................ 29
HS .............................................................................. 29
HSPLL ........................................................................ 29
Internal Oscillator Block ............................................. 35
INTOSC ..................................................................... 29
INTRC ........................................................................ 29
Oscillator Selection .......................................................... 283
Oscillator Start-up Timer (OST) ......................................... 36
Oscillator Switching ............................................................ 31
Oscillator Transitions .......................................................... 32
Oscillator, Timer1 ..................................................... 135, 145
Oscillator, Timer3 ............................................................. 143
P
Packaging ........................................................................ 389
Details ...................................................................... 390
Marking .................................................................... 389
PICSTART Plus Development Programmer .................... 348
PIE Registers ................................................................... 101
Pin Functions
AVDD .......................................................................... 27
AVDD .......................................................................... 18
AVSS .......................................................................... 27
AVSS .......................................................................... 18
ENVREG .............................................................. 18, 27
LCDBIAS3 ............................................................ 16, 23
MCLR ................................................................... 12, 19
OSC1/CLKI/RA7 .................................................. 12, 19
OSC2/CLKO/RA6 ................................................ 12, 19
RA0/AN0 .............................................................. 12, 19
RA1/AN1/SEG18 ................................................. 12, 19
RA2/AN2/VREF- .................................................... 12, 19
RA3/AN3/VREF+ ................................................... 12, 19
RA4/T0CKI/SEG14 .............................................. 12, 19
RA5/AN4/SEG15 ................................................. 12, 19
RB0/INT0/SEG30 ................................................. 13, 20
RB1/INT1/SEG8 ................................................... 13, 20
RB2/INT2/SEG9 ................................................... 13, 20
RB3/INT3/SEG10 ................................................. 13, 20
RB4/KBI0/SEG11 ................................................. 13, 20
RB5/KBI1/SEG29 ................................................. 13, 20
RB6/KBI2/PGC .................................................... 13, 20
RB7/KBI3/PGD .................................................... 13, 20
RC0/T1OSO/T13CKI ........................................... 14, 21
RC1/T1OSI/CCP2/SEG32 ................................... 14, 21
RC2/CCP1/SEG13 ............................................... 14, 21
RC3/SCK/SCL/SEG17 ......................................... 14, 21
RC4/SDI/SDA/SEG16 .......................................... 14, 21
RC5/SDO/SEG12 ................................................ 14, 21
RC6/TX1/CK1/SEG27 .......................................... 14, 21
RC7/RX1/DT1/SEG28 ......................................... 14, 21
RD0/SEG0 ........................................................... 15, 22
RD0/SEG1 ........................................................... 15, 22
RD2/SEG2 ........................................................... 15, 22
RD3/SEG3 ........................................................... 15, 22
RD4/SEG4 ........................................................... 15, 22
RD5/SEG5 ........................................................... 15, 22
RD6/SEG6 ........................................................... 15, 22
RD7/SEG7 ........................................................... 15, 22
RE0/LCDBIAS1 .................................................... 16, 23
RE1/LCDBIAS2 .................................................... 16, 23
RE3/COM0 ........................................................... 16, 23
DS39770B-page 402
RE4/COM1 .......................................................... 16, 23
RE5/COM2 .......................................................... 16, 23
RE6/COM3 .......................................................... 16, 23
RE7/CCP2/SEG31 ............................................... 16, 23
RF1/AN6/C2OUT/SEG19 .................................... 17, 24
RF2/AN7/C1OUT/SEG20 .................................... 17, 24
RF3/AN8/SEG21 ................................................. 17, 24
RF4/AN9/SEG22 ................................................. 17, 24
RF5/AN10/CVREF/SEG23 .................................... 17, 24
RF6/AN11/SEG24 ............................................... 17, 24
RF7/AN5/SS/SEG25 ............................................ 17, 24
RG0/LCDBIAS0 ................................................... 18, 25
RG1/TX2/CK2 ...................................................... 18, 25
RG2/RX2/DT2/VLCAP1 ......................................... 18, 25
RG3/VLCAP2 ........................................................ 18, 25
RG4/SEG26 ......................................................... 18, 25
RH0/SEG47 ............................................................... 26
RH1/SEG46 ............................................................... 26
RH2/SEG45 ............................................................... 26
RH3/SEG44 ............................................................... 26
RH4/SEG40 ............................................................... 26
RH5/SEG41 ............................................................... 26
RH6/SEG42 ............................................................... 26
RH7/SEG43 ............................................................... 26
RJ0 ............................................................................ 27
RJ1/SEG33 ................................................................ 27
RJ2/SEG34 ................................................................ 27
RJ3/SEG35 ................................................................ 27
RJ4/SEG39 ................................................................ 27
RJ5/SEG38 ................................................................ 27
RJ6/SEG37 ................................................................ 27
RJ7/SEG36 ................................................................ 27
VDD ............................................................................ 27
VDD ............................................................................ 18
VDDCORE/VCAP ..................................................... 18, 27
VSS ............................................................................ 27
VSS ............................................................................ 18
Pinout I/O Descriptions
PIC18F6XJ90 ............................................................ 12
PIC18F8XJ90 ............................................................ 19
PIR Registers ..................................................................... 98
PLL .................................................................................... 34
ECPLL Oscillator Mode ............................................. 34
HSPLL Oscillator Mode ............................................. 34
POP ................................................................................. 324
POR. See Power-on Reset.
PORTA
Associated Registers ............................................... 111
LATA Register ......................................................... 110
PORTA Register ...................................................... 110
TRISA Register ........................................................ 110
PORTB
Associated Registers ............................................... 114
LATB Register ......................................................... 112
PORTB Register ...................................................... 112
RB7:RB4 Interrupt-on-Change Flag (RBIF Bit) ........ 112
TRISB Register ........................................................ 112
PORTC
Associated Registers ............................................... 117
LATC Register ......................................................... 115
PORTC Register ...................................................... 115
RC3/SCK/SCL Pin ................................................... 201
TRISC Register ........................................................ 115
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
PORTD
Associated Registers ............................................... 119
LATD Register ......................................................... 118
PORTD Register ...................................................... 118
TRISD Register ........................................................ 118
PORTE
Associated Registers ............................................... 121
LATE Register .......................................................... 120
PORTE Register ...................................................... 120
TRISE Register ........................................................ 120
PORTF
Associated Registers ............................................... 124
LATF Register .......................................................... 122
PORTF Register ...................................................... 122
TRISF Register ........................................................ 122
PORTG
Associated Registers ............................................... 126
LATG Register ......................................................... 125
PORTG Register ...................................................... 125
TRISG Register ........................................................ 125
PORTH
Associated Registers ............................................... 128
LATH Register ......................................................... 127
PORTH Register ...................................................... 127
TRISH Register ........................................................ 127
PORTJ
Associated Registers ............................................... 130
LATJ Register .......................................................... 129
PORTJ Register ....................................................... 129
TRISJ Register ......................................................... 129
Power-Managed Modes ..................................................... 37
and SPI Operation ................................................... 193
Clock Sources ............................................................ 37
Clock Transitions and Status Indicators ..................... 38
Entering ...................................................................... 37
Exiting Idle and Sleep Modes .................................... 43
By Interrupt ........................................................ 43
By Reset ............................................................ 43
By WDT Time-out .............................................. 43
Without an Oscillator Start-up Delay .................. 43
Idle Modes ................................................................. 41
PRI_IDLE ........................................................... 42
RC_IDLE ............................................................ 43
SEC_IDLE ......................................................... 42
Multiple Sleep Commands ......................................... 38
Run Modes ................................................................. 38
PRI_RUN ........................................................... 38
RC_RUN ............................................................ 40
SEC_RUN .......................................................... 38
Selecting .................................................................... 37
Sleep Mode ................................................................ 41
Summary (table) ........................................................ 37
Power-on Reset (POR) ...................................................... 47
Power-up Delays ................................................................ 36
Power-up Timer (PWRT) ............................................. 36, 48
Time-out Sequence .................................................... 48
Prescaler, Capture ........................................................... 150
Prescaler, Timer0 ............................................................. 133
Prescaler, Timer2 ............................................................. 154
PRI_IDLE Mode ................................................................. 42
PRI_RUN Mode ................................................................. 38
Program Counter ............................................................... 59
PCL, PCH and PCU Registers ................................... 59
PCLATH and PCLATU Registers .............................. 59
© 2007 Microchip Technology Inc.
Program Memory
Extended Instruction Set ........................................... 76
Flash Configuration Words ........................................ 58
Hard Memory Vectors ................................................ 58
Instructions ................................................................ 63
Two-Word .......................................................... 63
Interrupt Vector .......................................................... 58
Look-up Tables .......................................................... 61
Memory Maps ............................................................ 57
Hard Vectors and Configuration Words ............. 58
Reset Vector .............................................................. 58
Program Verification and Code Protection ...................... 294
Programming, Device Instructions ................................... 295
Pulse-Width Modulation. See PWM (CCP Module).
PUSH ............................................................................... 324
PUSH and POP Instructions .............................................. 60
PUSHL ............................................................................. 340
PWM (CCP Module)
Associated Registers ............................................... 155
Duty Cycle ............................................................... 154
Example Frequencies/Resolutions .......................... 154
Period ...................................................................... 153
Setup for PWM Operation ....................................... 155
TMR2 to PR2 Match ................................................ 153
Q
Q Clock ............................................................................ 154
R
RAM. See Data Memory.
RC_IDLE Mode .................................................................. 43
RC_RUN Mode .................................................................. 40
RCALL ............................................................................. 325
RCON Register
Bit Status During Initialization .................................... 50
Reader Response ............................................................ 408
Register File ....................................................................... 67
Register File Summary ................................................ 69–72
Registers
ADCON0 (A/D Control 0) ......................................... 263
ADCON1 (A/D Control 1) ......................................... 264
ADCON2 (A/D Control 2) ......................................... 265
BAUDCON1 (Baud Rate Control 1) ......................... 232
CCPxCON (CCPx Control) ...................................... 147
CMCON (Comparator Control) ................................ 273
CONFIG1H (Configuration 1 High) .......................... 285
CONFIG1L (Configuration 1 Low) ........................... 285
CONFIG2H (Configuration 2 High) .......................... 287
CONFIG2L (Configuration 2 Low) ........................... 286
CONFIG3H (Configuration 3 High) .......................... 287
CVRCON (Comparator Voltage Reference Control) 279
DEVID1 (Device ID Register 1) ............................... 288
DEVID2 (Device ID Register 2) ............................... 288
EECON1 (EEPROM Control 1) ................................. 83
INTCON (Interrupt Control) ....................................... 95
INTCON2 (Interrupt Control 2) .................................. 96
INTCON3 (Interrupt Control 3) .................................. 97
IPR1 (Peripheral Interrupt Priority 1) ....................... 104
IPR2 (Peripheral Interrupt Priority 2) ....................... 105
IPR3 (Peripheral Interrupt Priority 3) ....................... 106
LCDCON (LCD Control) .......................................... 158
LCDDATAx (LCD Data) ........................................... 161
LCDPS (LCD Phase) ............................................... 159
LCDREG (LCD Voltage Regulator Control) ............. 163
LCDSEx (LCD Segment Enable) ............................. 160
OSCCON (Oscillator Control) .................................... 30
Preliminary
DS39770B-page 403
PIC18F85J90 FAMILY
OSCTUNE (Oscillator Tuning) ................................... 31
PIE1 (Peripheral Interrupt Enable 1) ........................ 101
PIE2 (Peripheral Interrupt Enable 2) ........................ 102
PIE3 (Peripheral Interrupt Enable 3) ........................ 103
PIR1 (Peripheral Interrupt Request (Flag) 1) ............. 98
PIR2 (Peripheral Interrupt Request (Flag) 2) ............. 99
PIR3 (Peripheral Interrupt Request (Flag) 3) ........... 100
RCON (Reset Control) ....................................... 46, 107
RCSTA1 (EUSART Receive Status and Control) .... 231
RCSTA2 (AUSART Receive Status and Control) .... 251
SSPCON1 (MSSP Control 1, I2C Mode) ................. 196
SSPCON1 (MSSP Control 1, SPI Mode) ................. 187
SSPCON2 (MSSP Control 2, I2C Master Mode) ..... 197
SSPCON2 (MSSP Control 2, I2C Slave Mode) ....... 198
SSPSTAT (MSSP Status, I2C Mode) ....................... 195
SSPSTAT (MSSP Status, SPI Mode) ...................... 186
STATUS ..................................................................... 73
STKPTR (Stack Pointer) ............................................ 60
T0CON (Timer0 Control) .......................................... 131
T1CON (Timer1 Control) .......................................... 135
T2CON (Timer2 Control) .......................................... 141
T3CON (Timer3 Control) .......................................... 143
TXSTA1 (EUSART Transmit Status and Control) .... 230
TXSTA2 (AUSART Transmit Status and Control) .... 250
WDTCON (Watchdog Timer Control) ....................... 289
RESET ............................................................................. 325
Reset .................................................................................. 45
Brown-out Reset (BOR) ............................................. 45
MCLR Reset, During Power-Managed Modes ........... 45
MCLR Reset, Normal Operation ................................ 45
Power-on Reset (POR) .............................................. 45
RESET Instruction ..................................................... 45
Stack Full Reset ......................................................... 45
Stack Underflow Reset .............................................. 45
Watchdog Timer (WDT) Reset ................................... 45
Resets .............................................................................. 283
Brown-out Reset (BOR) ........................................... 283
Oscillator Start-up Timer (OST) ............................... 283
Power-on Reset (POR) ............................................ 283
Power-up Timer (PWRT) ......................................... 283
RETFIE ............................................................................ 326
RETLW ............................................................................. 326
RETURN .......................................................................... 327
Return Address Stack ........................................................ 59
Return Stack Pointer (STKPTR) ........................................ 60
RLCF ................................................................................ 327
RLNCF ............................................................................. 328
RRCF ............................................................................... 328
RRNCF ............................................................................. 329
S
SCK .................................................................................. 185
SDI ................................................................................... 185
SDO ................................................................................. 185
SEC_IDLE Mode ................................................................ 42
SEC_RUN Mode ................................................................ 38
Serial Clock, SCK ............................................................. 185
Serial Data In (SDI) .......................................................... 185
Serial Data Out (SDO) ..................................................... 185
Serial Peripheral Interface. See SPI Mode.
SETF ................................................................................ 329
Slave Select (SS) ............................................................. 185
SLEEP .............................................................................. 330
Sleep
OSC1 and OSC2 Pin States ...................................... 36
Software Simulator (MPLAB SIM) .................................... 346
DS39770B-page 404
Special Event Trigger. See Compare (CCP Module).
Special Features of the CPU ........................................... 283
SPI Mode (MSSP)
Associated Registers ............................................... 193
Bus Mode Compatibility ........................................... 193
Effects of a Reset .................................................... 193
Enabling SPI I/O ...................................................... 189
Master Mode ............................................................ 190
Master/Slave Connection ......................................... 189
Operation ................................................................. 188
Operation in Power-Managed Modes ...................... 193
Serial Clock .............................................................. 185
Serial Data In ........................................................... 185
Serial Data Out ........................................................ 185
Slave Mode .............................................................. 191
Slave Select ............................................................. 185
Slave Select Synchronization .................................. 191
SPI Clock ................................................................. 190
Typical Connection .................................................. 189
SS .................................................................................... 185
SSPOV ............................................................................ 219
SSPOV Status Flag ......................................................... 219
SSPSTAT Register
R/W Bit ............................................................ 199, 201
Stack Full/Underflow Resets .............................................. 61
SUBFSR .......................................................................... 341
SUBFWB ......................................................................... 330
SUBLW ............................................................................ 331
SUBULNK ........................................................................ 341
SUBWF ............................................................................ 331
SUBWFB ......................................................................... 332
SWAPF ............................................................................ 332
T
Table Pointer Operations (table) ........................................ 84
Table Reads/Table Writes ................................................. 61
TBLRD ............................................................................. 333
TBLWT ............................................................................. 334
Timer0 .............................................................................. 131
Associated Registers ............................................... 133
Clock Source Select (T0CS Bit) ............................... 132
Operation ................................................................. 132
Overflow Interrupt .................................................... 133
Prescaler ................................................................. 133
Switching Assignment ..................................... 133
Prescaler Assignment (PSA Bit) .............................. 133
Prescaler Select (T0PS2:T0PS0 Bits) ..................... 133
Prescaler. See Prescaler, Timer0.
Reads and Writes in 16-Bit Mode ............................ 132
Source Edge Select (T0SE Bit) ............................... 132
Timer1 .............................................................................. 135
16-Bit Read/Write Mode .......................................... 137
Associated Registers ............................................... 139
Interrupt ................................................................... 138
Operation ................................................................. 136
Oscillator .......................................................... 135, 137
Layout Considerations ..................................... 138
Oscillator, as Secondary Clock .................................. 31
Overflow Interrupt .................................................... 135
Resetting, Using the CCP Special Event Trigger .... 138
TMR1H Register ...................................................... 135
TMR1L Register ....................................................... 135
Use as a Clock Source ............................................ 137
Use as a Real-Time Clock ....................................... 138
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
Timer2 .............................................................................. 141
Associated Registers ............................................... 142
Interrupt .................................................................... 142
Operation ................................................................. 141
Output ...................................................................... 142
PR2 Register ............................................................ 153
TMR2 to PR2 Match Interrupt .................................. 153
Timer3 .............................................................................. 143
16-Bit Read/Write Mode ........................................... 145
Associated Registers ............................................... 145
Operation ................................................................. 144
Oscillator .......................................................... 143, 145
Overflow Interrupt ............................................ 143, 145
Special Event Trigger (CCP) .................................... 145
TMR3H Register ...................................................... 143
TMR3L Register ....................................................... 143
Timing Diagrams
A/D Conversion ........................................................ 385
Acknowledge Sequence .......................................... 222
Asynchronous Reception ................................. 241, 257
Asynchronous Transmission ............................ 239, 255
Asynchronous Transmission (Back to Back) ... 239, 255
Automatic Baud Rate Calculation ............................ 237
Auto-Wake-up Bit (WUE) During Normal Operation 242
Auto-Wake-up Bit (WUE) During Sleep ................... 242
Baud Rate Generator with Clock Arbitration ............ 216
BRG Overflow Sequence ......................................... 237
BRG Reset Due to SDA Arbitration During Start Condition ................................................................... 225
Bus Collision During a Repeated Start Condition (Case
1) ...................................................................... 226
Bus Collision During a Repeated Start Condition (Case
2) ...................................................................... 226
Bus Collision During a Start Condition (SCL = 0) .... 225
Bus Collision During a Stop Condition (Case 1) ...... 227
Bus Collision During a Stop Condition (Case 2) ...... 227
Bus Collision During Start Condition (SDA Only) ..... 224
Bus Collision for Transmit and Acknowledge ........... 223
Capture/Compare/PWM ........................................... 373
CLKO and I/O .......................................................... 370
Clock Synchronization ............................................. 209
Clock/Instruction Cycle .............................................. 62
EUSART/AUSART Synchronous Receive (Master/
Slave) ............................................................... 383
EUSART/AUSART Synchronous Transmission (Master/
Slave) ............................................................... 383
Example SPI Master Mode (CKE = 0) ..................... 374
Example SPI Master Mode (CKE = 1) ..................... 375
Example SPI Slave Mode (CKE = 0) ....................... 376
Example SPI Slave Mode (CKE = 1) ....................... 377
External Clock (All Modes Except PLL) ................... 368
Fail-Safe Clock Monitor ............................................ 293
First Start Bit Timing ................................................ 217
I2C Bus Data ............................................................ 379
I2C Bus Start/Stop Bits ............................................. 378
I2C Master Mode (7 or 10-Bit Transmission) ........... 220
I2C Master Mode (7-Bit Reception) .......................... 221
I2C Slave Mode (10-Bit Reception, SEN = 0) .......... 205
I2C Slave Mode (10-Bit Reception, SEN = 0, ADMSK =
01001) .............................................................. 206
I2C Slave Mode (10-Bit Reception, SEN = 1) .......... 211
I2C Slave Mode (10-Bit Transmission) ..................... 207
I2C Slave Mode (7-bit Reception, SEN = 0) ............. 202
I2C Slave Mode (7-bit Reception, SEN = 0, ADMSK =
01011) .............................................................. 203
© 2007 Microchip Technology Inc.
Preliminary
I2C Slave Mode (7-Bit Reception, SEN = 1) ............ 210
I2C Slave Mode (7-Bit Transmission) ...................... 204
I2C Slave Mode General Call Address Sequence (7 or
10-Bit Address Mode) ...................................... 212
I2C Stop Condition Receive or Transmit Mode ........ 222
LCD Interrupt in Quarter Duty Cycle Drive .............. 180
LCD Sleep Entry/Exit When SLPEN = 1 or CS1:CS0 = 00
......................................................................... 181
MSSP I2C Bus Data ................................................ 381
MSSP I2C Bus Start/Stop Bits ................................. 381
PWM Output ............................................................ 153
Repeated Start Condition ........................................ 218
Reset, Watchdog Timer (WDT), Oscillator Start-up Timer
(OST) and Power-up Timer (PWRT) ............... 371
Send Break Character Sequence ............................ 243
Slave Synchronization ............................................. 191
Slow Rise Time (MCLR Tied to VDD, VDD Rise > TPWRT)
........................................................................... 49
SPI Mode (Master Mode) ........................................ 190
SPI Mode (Slave Mode, CKE = 0) ........................... 192
SPI Mode (Slave Mode, CKE = 1) ........................... 192
Synchronous Reception (Master Mode, SREN) ..... 246,
260
Synchronous Transmission ............................. 244, 258
Synchronous Transmission (Through TXEN) .. 245, 259
Time-out Sequence on Power-up (MCLR Not Tied to
VDD), Case 1 ..................................................... 48
Time-out Sequence on Power-up (MCLR Not Tied to
VDD), Case 2 ..................................................... 49
Time-out Sequence on Power-up (MCLR Tied to VDD,
VDD Rise Tpwrt) ................................................. 48
Timer0 and Timer1 External Clock .......................... 372
Transition for Entry to Idle Mode ............................... 42
Transition for Entry to SEC_RUN Mode .................... 39
Transition for Entry to Sleep Mode ............................ 41
Transition for Two-Speed Start-up (INTRC to HSPLL) ..
291
Transition for Wake From Idle to Run Mode .............. 42
Transition for Wake from Sleep (HSPLL) .................. 41
Transition From RC_RUN Mode to PRI_RUN Mode . 40
Transition From SEC_RUN Mode to PRI_RUN Mode
(HSPLL) ............................................................. 39
Transition to RC_RUN Mode ..................................... 40
Type-A in 1/2 MUX, 1/2 Bias Drive .......................... 170
Type-A in 1/2 MUX, 1/3 Bias Drive .......................... 172
Type-A in 1/3 MUX, 1/2 Bias Drive .......................... 174
Type-A in 1/3 MUX, 1/3 Bias Drive .......................... 176
Type-A in 1/4 MUX, 1/3 Bias Drive .......................... 178
Type-A/Type-B in Static Drive ................................. 169
Type-B in 1/2 MUX, 1/2 Bias Drive .......................... 171
Type-B in 1/2 MUX, 1/3 Bias Drive .......................... 173
Type-B in 1/3 MUX, 1/2 Bias Drive .......................... 175
Type-B in 1/3 MUX, 1/3 Bias Drive .......................... 177
Type-B in 1/4 MUX, 1/3 Bias Drive .......................... 179
DS39770B-page 405
PIC18F85J90 FAMILY
Timing Diagrams and Specifications
Capture/Compare/PWM Requirements ................... 373
CLKO and I/O Requirements ................................... 370
EUSART/AUSART Synchronous Receive Requirements
.......................................................................... 383
EUSART/AUSART Synchronous Transmission Requirements ............................................................... 383
Example SPI Mode Requirements (Master Mode, CKE =
0) ...................................................................... 374
Example SPI Mode Requirements (Master Mode, CKE =
1) ...................................................................... 375
Example SPI Mode Requirements (Slave Mode, CKE =
0) ...................................................................... 376
Example SPI Slave Mode Requirements (CKE = 1) 377
External Clock Requirements .................................. 368
I2C Bus Data Requirements (Slave Mode) .............. 380
I2C Bus Start/Stop Bits Requirements (Slave Mode) .....
378
Internal RC Accuracy ............................................... 369
MSSP I2C Bus Data Requirements ......................... 382
MSSP I2C Bus Start/Stop Bits Requirements .......... 381
PLL Clock ................................................................. 369
Reset, Watchdog Timer, Oscillator Start-up Timer, Power-up Timer and Brown-out Reset Requirements ..
371
Timer0 and Timer1 External Clock Requirements ... 372
Top-of-Stack Access .......................................................... 59
TSTFSZ ............................................................................ 335
Two-Speed Start-up ................................................. 283, 291
Two-Word Instructions
Example Cases .......................................................... 63
W
Watchdog Timer (WDT) ........................................... 283, 289
Associated Registers ............................................... 289
Control Register ....................................................... 289
During Oscillator Failure .......................................... 292
Programming Considerations .................................. 289
WCOL ...................................................... 217, 218, 219, 222
WCOL Status Flag ................................... 217, 218, 219, 222
WWW Address ................................................................ 407
WWW, On-Line Support ...................................................... 5
X
XORLW ............................................................................ 335
XORWF ........................................................................... 336
V
VDDCORE/VCAP Pin ........................................................... 290
Voltage Reference Specifications .................................... 364
Voltage Regulator (On-Chip) ............................................ 290
Brown-out Reset (BOR) ........................................... 291
Low-Voltage Detection (LVD) .................................. 290
Operation in Sleep Mode ......................................... 291
Power-up Requirements .......................................... 291
DS39770B-page 406
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata, application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Customers should contact their distributor, representative or field application engineer (FAE) for support.
Local sales offices are also available to help customers. A listing of sales offices and locations is included in
the back of this document.
Technical support is available through the web site
at: http://support.microchip.com
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com, click on Customer Change Notification and follow the registration instructions.
© 2007 Microchip Technology Inc.
Preliminary
DS39770B-page 407
PIC18F85J90 FAMILY
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
To:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
Device: PIC18F85J90 Family
Literature Number: DS39770B
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS39770B-page 408
Preliminary
© 2007 Microchip Technology Inc.
PIC18F85J90 FAMILY
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
X
/XX
XXX
Device
Temperature
Range
Package
Pattern
Examples:
a)
b)
Device
PIC18F63J90/64J90/65J90(1),
PIC18F83J90/84J90/85J90(1),
PIC18F63J90/64J90/65J90T(2),
PIC18F83J90/84J90/85J90T(2)
Temperature Range
I
= -40°C to +85°C (Industrial)
Package
PT
= TQFP (Thin Quad Flatpack)
Pattern
QTP, SQTP, Code or Special Requirements
(blank otherwise)
© 2007 Microchip Technology Inc.
Preliminary
PIC18F85J90-I/PT 301 = Industrial temp.,
TQFP package, QTP pattern #301.
PIC18F63J90T-I/PT = Tape and reel, Industrial
temp., TQFP package.
Note 1: F
2: T
= Standard Voltage Range
= in tape and reel
DS39770B-page 409
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Habour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
Korea - Gumi
Tel: 82-54-473-4301
Fax: 82-54-473-4302
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Fuzhou
Tel: 86-591-8750-3506
Fax: 86-591-8750-3521
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Malaysia - Penang
Tel: 60-4-646-8870
Fax: 60-4-646-5086
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
China - Shunde
Tel: 86-757-2839-5507
Fax: 86-757-2839-5571
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Xian
Tel: 86-29-8833-7250
Fax: 86-29-8833-7256
12/08/06
DS39770B-page 410
Preliminary
© 2007 Microchip Technology Inc.