Series 280 ® Commercial Miniature 16mm Diameter Composition Variable Resistors Features • Miniature 16mm style • Bushing mounted with PC terminals and shaft parallel or perpendicular to PC board • Single, tandem or concentric units • RoHs compliant Available with: • Molded or metal shafts • ± 2% Linearity • Center detent Electrical and Mechanical Specifications Resistance Range 500 ohms through 5 megohms (linear taper). Resistance Tolerance Standard:±30% Special: ±20%, ±10% Power Rating, Watts 1/4 watt per section through 10K ohms 1/8 watt per section above 10K ohms Full rating @ 55°C derated to no load at 85°C for linear tapers (derating required on multiple section controls). Voltage Rating Bushings to Terminals: High pot test, one minute—750 VAC Operating maximum—500 VDC Insulation Resistance 100 megohms minimum @ 250 VDC Rotational Angle Total Rotation: 300°±5° Effective Rotation: 300°(approximate) Rotational Torque 21.6~216 g-cm (0.3~3 in-oz) Locating Lugs Available without lugs Mounting Information Standard: Bushing mount Diameter: 3/8”-32UNEF-2A or M8 x .75P thread Standard Length: 9.53mm(.375”) or 6.35mm(.250”) Special Length: Available as required Special: PCB, Bracket mount Across End Terminals: 350 VDC, load not to exceed power rating. Life Cycle Standard: 10K cycles Special: 100K ~ 500K cycles. 1-4 CTS Electronic Components © 2006 CTS Corporation. All rights reserved. Information subject to change. 10/25/06 www.ctscorp.com B280 Metal Shaft, Die casting bushing, "XB" style Terminals with Bracket 2 WIPER CCW MTG. SURFACE "L"± 19.8 .780 A± 18.0 .709 MAX. 0.8 .031 CIRCUIT MTG. SURFACE 5.00±0.05 .197±.002 10.2±0.4 .402±.016 6.35±0.05 .250±.002 8.5 .335 11.2 .441 3 CLOCKWISE 9.53±0.05 .375±.002 0.4 .016 CW 1 19.06±0.05 .750±.002 Ø1.40 (3)HL'S .055 12.5 .492 2.54±0.05 .100±.002 12.70±0.05 .500±.002 M7X.75P 1 Ø2.08±0.05 (4)HL'S .082±.002 3 2 16.4 .646 RECOMMENDED PCB LAYOUT DIMENSION: mm INCH T280 Metal Shaft, Bushing mount, Type “T” Solder Lug Terminals MTG. SURFACE "L"±0.8 ±.031 10.2±0.4 .402±.016 MAX. 18.0 .709 "A"±0.4 ±.016 MAX. 8.5 .335 7.9±.013 .311±.002 2 WIPER CCW CW 1 3 CLOCKWISE 11.2 .441 3/8-32UNEF-2A CIRCUIT 10.9 .429 1 2.18X1.52 .086X.060 2 3 2.92±0.08 .115±.003 HL'S(3) 16.4 .646 DIMENSION: mm INCH X280 Metal Shaft, Bushing Mounting, Printed Circuit Type "X" Terminals MTG. SURFACE 10.2±0.4 .402±.016 18.00 .709 MAX. "L"±0.8 .031 "A"±0.4 10.00±0.05 .394±.002 .016 8.5 .335 7.9±0.13 .311±.005 5.00±0.05 .197±.002 MAX. 2 MTG. SURFACE WIPER CCW CW 1 11.20 .441 12.50 .492 3/8-32UNEF-2A 3 CLOCKWISE 6.83±0.05 .269±.002 CIRCUIT Ø1.40 (3) .055 1 2 16.4 3 .646 RECOMMENDED PCB LAYOUT DIMENSION: 2-4 CTS Electronic Components © 2006 CTS Corporation. All rights reserved. Information subject to change. mm INCH 10/25/06 www.ctscorp.com V280 Metal Shaft, Bushing Mounting, Printed Circuit Type "V" Terminals MTG. SURFACE 10.2±0.4 .402±.016 18.0 .709 MAX. 8.5 .335 3/8-32UNEF-2A CENTER LINE OF POT MAX. 7.9±.013 .311±.005 12.70±0.05 .500±.002 12.5 .492 "A"± 1 3 2 6.4 .252 16.4 .646 0.4 .016 0.8 "L"± .031 WIPER 2 CCW CW 1 Ø2.08±0.05 (4)HL'S. .082±.002 3 CLOCKWISE CIRCUIT RECOMMENDED PCB LAYOUT mm INCH DIMENSION: X2-280 Dual Section, Metal Shaft, Bushing Mounting, Printed Circuit Type "X" Terminals MTG. SURFACE 18.0 .709 MAX. MTG. SURFACE 3/8-32UNEF-2A 8.5 .335 7.9±0.13 .311±.005 11.2 .441 1 4 2 3 5 6 3.68±0.05 .145±.002 MAX. 2 12.5 .492 CW 1 3 4 6 5 0.4 "A"± .016 15.1±0.4 .594±.016 16.4 .646 WIPER CCW 8.10±0.05 .319±.002 WIPER Ø1.40 (6)HL'S. .055 CLOCKWISE CIRCUIT 0.4 "L"± .016 5.00±0.05 .197±.002 10.00±0.05 .394±.002 RECOMMENDED PCB LAYOUT mm INCH DIMENSION: BC2-280 Dual Section, Metal Shaft, Bushing Mounting, Printed Circuit Type "XB" Terminals with Bracket MTG. SURFACE 19.8 .780 "L2"± "L1"± 0.8 .031 MAX. 18.0 .709 MTG. SURFACE. 0.8 .031 19.06±0.05 .750±.002 9.53±0.05 .375±.002 DIMENSION: 5.00±0.05 .197±.002 2.54±0.05 .100±.002 15.1±0.4 .594±.016 6.35±0.05 .250±.002 8.5 .335 MAX. 7.9±0.13 .311±.005 11.2 .441 7.49±0.05 .295±.002 12.70±0.05 12.5 .492 .500±.002 "A"± 1 2 3 4 5 6 mm INCH 0.4 .016 3/8-32 UNEF-2A 10.00±0.05 Ø1.40 (6)HL'S. .055 .394±.002 Ø2.08±0.05 (4)HL'S. .082±.002 RECOMMENDED PCB LAYOUT 16.4 .646 2 WIPER CCW CW 1 3 4 6 5 WIPER CLOCKWISE CIRCUIT 3-4 CTS Electronic Components © 2006 CTS Corporation. All rights reserved. Information subject to change. 10/25/06 www.ctscorp.com V280-SPL Hollow Shaft Type, Printed Circuit “X” Type Terminals, 360 degree endless rotation angle. 17.06 .672 18.00 MAX. .709 Ø1.90 .075 8.5 MAX. .335 12.70±0.05 .500±.002 4.05 Ø .160 10.19 .401 Ø7.50 .295 Ø1.40 (3)HL'S. .055 12.50 .492 3.05 .120 1.52 (2 ) .060 MOUNTING SURFACE 0.50 .020 5.00(2) .197 0.99 TYP. .039 5.00(2) RECOMMENDED PCB LAYOUT .197 2.00 1 3.41 1.20 .047 1 3 2 3 2 2 WIPER CCW 16.40 .646 CW 1 3 CLOCKWISE CIRCUIT mm DIMENSION: INCH Ordering Information 280 X 2 20 TERMINAL STYLE B – XB STYLE T – SOLDER LUG X – PC (X STYLE) V – PC FORMED TO REAR MOUNTING STYLE “A” R 103 SHAFT TRIM RESIST TOL R – ROUND F – F x 4.5mm (For metric size) .375 x .156" (For inch size) K – 18 TEETH (For metric size) 24 TEETH (For inch size) S – SD SLOT 0 – HOLLOW TYPE A – ±10% B – ±20% C – ±30% A – 5.0mm 2 – .250" B – 6.35mm 3 – .375" C – 7.0mm 8 – 1.000" D – 9.5mm ALL M8 x .75P ALL 3/8-32 UNEF 0 – Hollow Type Z – 4.8mm M7 x .75P 1 SPECIALS 1 – NONE 2 – CENTER DETENT TAPER 1 – LINEAR 2 – 10% AUD 3 – 10% CCW AUD LINEARITY BUSHING LENGTH: 1/8" (3.2mm) INCREMENTS EXAMPLES: mm inch 5 1 B SHAFT LENGTH “L” FROM MOUNTING SURFACE 1/32" (0.8mm) INCREMENTS mm EXAMPLES: inch A0 – 10mm 20 – .625" A5 – 15mm 24 – .750" B0 – 20mm 28 – .875" B5 – 25mm 32 – 1.000" C0 – 30mm RESISTANCE CODE EXAMPLES CODE 501 102 252 502 103 253 503 104 RESISTANCE 500 OHMS 1K 2.5K 5K 10K 25K 50K 100K 5 – ±5% 3 – ±3% * 2 – ±2% CTS for * Consult details. C5 – 35mm ALL 6.0mm Dia. ALL .250" Dia. 00 – Hollow Type 4-4 CTS Electronic Components © 2006 CTS Corporation. All rights reserved. Information subject to change. 10/25/06 www.ctscorp.com