plerowTM ALN2045R2 Internally Matched LNA Module Features Description · S21 = 26.3 dB @ 1920 MHz = 24.7 dB @ 2170 MHz · NF of 0.95 dB over Frequency · Unconditionally Stable · Single 5V Supply · High OIP3 @ Low Current The plerowTM ALN-series is the compactly designed surface-mount module for the use of the LNA with or without the following gain blocks in the infrastructure equipment of the mobile wireless (CDMA, GSM, PCS, PHS, WCDMA, DMB, WLAN, WiBro, WiMAX), GPS, satellite communication terminals, CATV and so on. It has an exceptional performance of low noise figure, high gain, high OIP3, and low bias current. The stability factor is always kept more than unity over the application band in order to ensure its unconditionally stable implementation to the application system environment. The surface-mount module package including the completed matching circuit and other components necessary just in case allows very simple and convenient implementation onto the system board in mass production level. Specifications (in Production) 2-stage Single Type Typ. @ T = 25°C, Vs = 5 V, Freq. = 2045 MHz, Zo.sys = 50 ohm Parameter Unit Frequency Range Specifications Min Typ Max MHz 1920 Gain dB 24.5 Gain Flatness dB ± 0.8 ± 1.0 Noise Figure dB 0.95 1.0 Output IP3 S11 / S22 (1) dBm (2) 2170 35.5 dBm (3) Tel: (82) 42-528-7223 Fax: (82) 42-528-7222 -18 / -10 19.5 20.5 µsec - Supply Current mA 110 Supply Voltage V 5 Impedance Ω 50 Switching Time Website: www.asb.co.kr E-mail: [email protected] 36.5 dB Output P1dB More Information 25.5 ASB Inc., 4th Fl. Venture Town Bldg., 367-17 Goijeong-Dong, Seo-Gu, Daejon 302-716, Korea 130 Max. RF Input Power dBm C.W 23 ~ 25 (before fail) Package Type & Size mm Surface Mount Type, 10Wx10Lx3.8H Operating temperature is -40°C to +85°C. 1) OIP3 is measured with two tones at an output power of 10 dBm / tone separated by 1 MHz. 2) S11/S22 (max) is the worst value within the frequency band. 3) Switching time means the time that takes for output power to get stabilized to its final level after switching DC voltage from 0 V to VS. Outline Drawing (Unit: mm) plerow Pin Number Function ALN2045R2 2 RF In ASB Inc. 4 +Vcc (Top View) (Bottom View) Solder Stencil Area 6 RF Out Others Ground Note: 1. The number and size of ground via holes in a circuit board is critical for thermal RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of all ground pins for better RF and thermal performance, as shown in the drawing at the left side. (Side View) Ø0.4 plated thru holes to ground plane (Recommended Footprint) 1/6 www.asb.co.kr November 2008 plerowTM ALN2045R2 Internally Matched LNA Module S-parameters Typical Performance Performance Typical (Measured) (Measured) 1920~2170 1920~2170 +5 V +5 V Noise Figure S-parameters & K Factor OIP3 2/6 P1dB www.asb.co.kr November 2008 plerowTM ALN2045R2 Internally Matched LNA Module S-parameters Typical Performance (Measured) 1970 ± 15 +5 V Stability Factor (K) Noise Figure OIP3 3/6 P1dB www.asb.co.kr November 2008 plerowTM ALN2045R2 Internally Matched LNA Module S-parameters Typical Performance (Measured) 2160 ± 15 +5 V Stability Factor (K) Noise Figure OIP3 4/6 P1dB www.asb.co.kr November 2008 plerowTM ALN2045R2 Internally Matched LNA Module RF Performance with Voltage Change Item S11 (dB) S22 (dB) S21 (dB) G/F (dB) NF (dB) P1dB (dBm) OIP3 (dBm) Current (mA) 4.5 -19.18 -16.30 25.17 1.68 0.953 21.57 34.72 83 4.6 -19.31 -16.21 25.25 1.71 0.954 21.79 35.94 89 4.7 -19.39 -16.18 25.32 1.68 0.967 22.00 37.04 95 4.8 -19.45 -16.19 25.37 1.70 0.986 22.17 38.20 100 4.9 -19.51 -16.15 25.43 1.67 0.978 22.46 38.60 106 5.0 -19.59 -16.15 25.47 1.69 0.980 22.62 38.84 112 5.1 -19.65 -16.14 25.47 1.69 0.997 22.75 38.94 117 5.2 -19.73 -16.16 25.50 1.69 1.018 22.90 39.06 123 5.3 -19.74 -16.15 25.56 1.67 1.007 23.11 39.03 128 5.4 -19.90 -16.17 25.58 1.70 1.019 23.25 38.87 134 5.5 -19.91 -16.18 25.60 1.69 1..040 23.38 38.78 139 Voltage RF Performance with Operating Temperature Item S11 (dB) S22 (dB) S21 (dB) G/F (dB) NF (dB) P1dB (dBm) OIP3 (dBm) Current (mA) - 40°C -19.14 -15.89 25.93 1.68 0.698 23.18 39.10 104 - 20°C -19.23 -16.07 25.77 1.69 0.771 23.10 39.09 106 0°C -19.17 -16.13 25.60 1.70 0.860 22.92 39.05 108 25°C -19.15 -16.01 25.34 1.72 0.986 22.62 38.89 111 40°C -19.10 -16.26 25.20 1.73 1.117 22.43 38.63 112 60°C -18.86 -16.37 25.04 1.73 1.243 22.07 37.41 113 80°C -18.86 -16.41 24.84 1.73 1.297 21.64 35.66 113 100°C -18.82 -16.51 24.52 1.73 1.454 21.06 34.19 112 Temp. 5/6 www.asb.co.kr November 2008 plerowTM ALN2045R2 Internally Matched LNA Module Application Circuit V DC + - Tantal Capacitor IN OUT ALN C1 C2 1) The tantal capacitor is optional and for bypassing the AC noise introduced from the DC supply. The capacitance value may be determined by customer’s DC supply status. 2) So-called DC blocking capacitors are always necessarily placed at the input and output port for allowing only the RF signal to pass and blocking the DC component in the signal. The DC blocking capacitors are included inside the LNA module. Therefore, C1 & C2 capacitors may not be necessary, but can be added just in case that the customer wants. The value of C1 & C2 is determined by considering the application frequency. Recommended Soldering Reflow Process Evaluation Board Layout 20~40 sec 260°C Ramp-up (3˚C/sec) Ramp-down (6°C/sec) OUT IN 200°C 150°C +Vcc 60~180 sec Size 25 x 25mm (for ALN-R Series – 10x10mm) 6/6 www.asb.co.kr November 2008