ETC CMD6392

CMD6392
4-Channel BTL Driver for Players
The CMD6392FP is a 4-channel BTL driver for CD player motors and actuators. It has an internal primary filter, and can
be directly connected (without attached components) to the servo PWM output of all drivers other than the spindle driver.
Applications
CD players, CD-ROM drives
Features
1) HSOP 28-pin package allows for miniaturization of
applications.
2) PWM input is filtered by the internal primary filter,
eliminating the need for attached resistors and capacitors, thereby helping reduce the number of components. Resistor and capacitor time constants can
also be changed with attached components.
3) Internal thermal shutdown circuit.
4) Internal mute circuit.
Absolute maximum ratings (Ta = 25C)
Recommended operating conditions (Ta = 25C)
* All specs and applications shown above subject to change without prior notice.
1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN
Email: [email protected]
Tel:886-3-3214525
Http: www.ceramate.com.tw
Page 1 of 8
Rev 1.2 Oct.24, 2002
Fax:886-3-3521052
CMD6392
4-Channel BTL Driver for Players
Block diagram
* All specs and applications shown above subject to change without prior notice.
1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN
Email: [email protected]
Tel:886-3-3214525
Http: www.ceramate.com.tw
Page 2 of 8
Rev 1.2 Oct.24, 2002
Fax:886-3-3521052
CMD6392
4-Channel BTL Driver for Players
Pin descriptions
* All specs and applications shown above subject to change without prior notice.
1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN
Email: [email protected]
Tel:886-3-3214525
Http: www.ceramate.com.tw
Page 3 of 8
Rev 1.2 Oct.24, 2002
Fax:886-3-3521052
CMD6392
4-Channel BTL Driver for Players
Electrical characteristics (unless otherwise noted, Ta = 25C, VCC = 8V, f = 1kHz, RL = 8Ω)
-25
* All specs and applications shown above subject to change without prior notice.
1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN
Email: [email protected]
Tel:886-3-3214525
Http: www.ceramate.com.tw
Page 4 of 8
Rev 1.2 Oct.24, 2002
Fax:886-3-3521052
CMD6392
4-Channel BTL Driver for Players
Input / output circuits
Circuit operation
(1) Fig. 3 shows the inputs from the digital servo IC for
CH1-CH3 drivers (all drivers except the spindle).
SW1 is on when the forward input signal (HIGH level,
over 2.4V) is present. SW2 is on when the reverse input
signal is present (Fig. 2)
The constan current (I1)at this time enters the RC and
generates an integral waveform based on the duty of the
input waveform. The BTL is output from BUF1 and BUF2
(Fig. 4).
To maintain the HIGH level with forward (or reverse) input, the DC voltage generated at point A is :
I1 R 2.5V (reverse : 2.5V)
This is the voltage generated relative VREF. The setting is
such that a voltage differential of 5V is generated between output pins. The time constant is :
R C = 2.4µsec
* All specs and applications shown above subject to change without prior notice.
1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN
Email: [email protected]
Tel:886-3-3214525
Http: www.ceramate.com.tw
Page 5 of 8
Rev 1.2 Oct.24, 2002
Fax:886-3-3521052
CMD6392
4-Channel BTL Driver for Players
This can be increased by inserting a capacitor between
point A (pins 3, 11 and 18) and VREF. The constant current
(Iconst) given in the electrical characteristics refers to I1
and I2 in Fig. 2.
Operation notes
(1) The CMD6392FP has an internal thermal shutdown
circuit. Output current is muted when the chip temperature exceeds 180C (typically).
(2) The output current can also be muted by lowering
the mute pin (pin 15) voltage below 0.5V.
(3) All four driver output channels are muted during
thermal shutdown, muting and a drop in bias pin voltage.
No other components are muted.
(2) CH4 driver (spindle driver)
Pins 23 and 25 are shorted inside the IC. Bias amplitudes
are the primary type of inputs assumed. The level shift
circuit converts the pre-stage amplifier output (centered
on the bias level and impressed on pins 23 and 25) to
positive and negative amplitudes centered on VREF. The
level shift circuit’s output is BTL-output from the buffer
amplifier.
Because of the high input impedance, the IC is designed
to accommodate a filter comprising attached resistors
and capacitors.
(Example) For secondary filters
* All specs and applications shown above subject to change without prior notice.
1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN
Email: [email protected]
Tel:886-3-3214525
Http: www.ceramate.com.tw
Page 6 of 8
Rev 1.2 Oct.24, 2002
Fax:886-3-3521052
CMD6392
4-Channel BTL Driver for Players
Electrical characteristics curves
* All specs and applications shown above subject to change without prior notice.
1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN
Email: [email protected]
Tel:886-3-3214525
Http: www.ceramate.com.tw
Page 7 of 8
Rev 1.2 Oct.24, 2002
Fax:886-3-3521052
CMD6392
4-Channel BTL Driver for Players
External dimensions (Units: mm)
HSOP-28
* All specs and applications shown above subject to change without prior notice.
1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN
Email: [email protected]
Tel:886-3-3214525
Http: www.ceramate.com.tw
Page 8 of 8
Rev 1.2 Oct.24, 2002
Fax:886-3-3521052