PCA9515 I2C-bus repeater Rev. 09 — 23 April 2009 Product data sheet 1. General description The PCA9515 is a BiCMOS integrated circuit intended for application in I2C-bus and SMBus systems. While retaining all the operating modes and features of the I2C-bus system, it permits extension of the I2C-bus by buffering both the data (SDAn) and the clock (SCLn) lines, thus enabling two buses of 400 pF. The I2C-bus capacitance limit of 400 pF restricts the number of devices and bus length. Using the PCA9515 enables the system designer to isolate two halves of a bus, thus more devices or longer length can be accommodated. It can also be used to run two buses, one at 5 V and the other at 3.3 V or a 400 kHz and 100 kHz bus, where the 100 kHz bus is isolated when 400 kHz operation of the other is required. Two or more PCA9515s cannot be put in series. The PCA9515 design does not allow this configuration. Since there is no direction pin, slightly different ‘legal’ low voltage levels are used to avoid lock-up conditions between the input and the output. A ‘regular low’ applied at the input of a PCA9515 will be propagated as a ‘buffered low’ with a slightly higher value. When this ‘buffered low’ is applied to another PCA9515, PCA9516A, or PCA9518A in series, the second PCA9515, PCA9516A, or PCA9518A will not recognize it as a ‘regular low’ and will not propagate it as a ‘buffered low’ again. The PCA9510A/9511A/9513A/9514A and PCA9512A cannot be used in series with the PCA9515, PCA9516A, or PCA9518A but can be used in series with themselves since they use shifting instead of static offsets to avoid lock-up conditions. The PCA9515 SCLn/SDAn Ci is about 200 pF versus the normal < 10 pF when VCC = 0 V. The newer PCA9515A should be used in applications where power is secured to the repeater but an active bus remains on either set of SCLn/SDAn pins to prevent this increase in bus loading. Additionally, the PCA9515A has a wider voltage range of 2.3 V to 3.6 V and can be used in applications with lower voltage supply constraints. 2. Features n n n n n n n n n 2 channel, bidirectional buffer I2C-bus and SMBus compatible Active HIGH repeater enable input Open-drain input/outputs Lock-up free operation Supports arbitration and clock stretching across the repeater Accommodates Standard-mode and Fast-mode I2C-bus devices and multiple masters Powered-off high-impedance I2C-bus pins Operating supply voltage range of 3.0 V to 3.6 V PCA9515 NXP Semiconductors I2C-bus repeater n 5.5 V tolerant I2C-bus (SCLn, SDAn) and enable (EN) pins n 0 Hz to 400 kHz clock frequency1 n ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 n Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA n Packages offered: SO8 and TSSOP8 (MSOP8) 3. Ordering information Table 1. Ordering information Type number Package Name Description Version PCA9515D SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 PCA9515DP TSSOP8[1] plastic thin shrink small outline package; 8 leads; body width 3 mm SOT505-1 [1] Also known as MSOP8. 3.1 Ordering options Table 2. Ordering options Type number Topside mark Temperature range PCA9515D PCA9515 Tamb = −40 °C to +85 °C PCA9515DP 9515 Tamb = −40 °C to +85 °C 4. Block diagram VCC PCA9515 SDA0 SDA1 SCL0 SCL1 pull-up resistor EN 002aae620 GND Fig 1. Block diagram of PCA9515 The output pull-down of each internal buffer is set for approximately 0.5 V, while the input threshold of each internal buffer is set about 0.07 V lower, when the output is internally driven LOW. This prevents a lock-up condition from occurring. 1. The maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater. PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 2 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 5. Pinning information 5.1 Pinning n.c. 1 8 VCC SCL0 2 7 SCL1 SDA0 3 6 SDA1 GND 4 5 EN PCA9515D n.c. 1 8 VCC SCL0 2 7 SCL1 SDA0 3 6 SDA1 GND 4 5 EN 002aac744 002aac743 Fig 2. PCA9515DP Pin configuration for SO8 Fig 3. Pin configuration for TSSOP8 5.2 Pin description Table 3. Pin description Symbol Pin Description n.c. 1 not connected SCL0 2 serial clock bus 0 SDA0 3 serial data bus 0 GND 4 supply ground EN 5 active HIGH repeater enable input SDA1 6 serial data bus 1 SCL1 7 serial clock bus 1 VCC 8 supply power PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 3 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 6. Functional description The PCA9515 BiCMOS integrated circuit contains two identical buffer circuits which enable I2C-bus and similar bus systems to be extended without degradation of system performance. (Refer to Figure 1 “Block diagram of PCA9515”.) The PCA9515 BiCMOS integrated circuit contains two bidirectional open-drain buffers specifically designed to support the standard low-level-contention arbitration of the I2C-bus. Except during arbitration or clock stretching, the PCA9515 acts like a pair of non-inverting, open-drain buffers, one for SDA and one for SCL. 6.1 Enable The EN pin is active HIGH with an internal pull-up and allows the user to select when the repeater is active. This can be used to isolate a badly behaved slave on power-up until after the system power-up reset. It should never change state during an I2C-bus operation because disabling during a bus operation will hang the bus and enabling part way through a bus cycle could confuse the I2C-bus parts being enabled. The enable pin (EN) should only change state when the global bus and the repeater port are in an idle state to prevent system failures. 6.2 I2C-bus systems As with the standard I2C-bus system, pull-up resistors are required to provide the logic HIGH levels on the buffered bus. (Standard open-collector configuration of the I2C-bus.) The size of these pull-up resistors depends on the system, but each side of the repeater must have a pull-up resistor. This part is designed to work with Standard-mode and Fast-mode I2C-bus devices in addition to SMBus devices. Standard-mode I2C-bus devices only specify 3 mA output drive; this limits the termination current to 3 mA in a generic I2C-bus system where Standard-mode devices and multiple masters are possible. Under certain conditions, higher termination currents can be used. Please see application note AN255, “I2C/SMBus Repeaters, Hubs and Expanders” for additional information on sizing resistors and precautions when using more than one PCA9515 in a system or using the PCA9515 in conjunction with the P82B96. PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 4 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 7. Application design-in information A typical application is shown in Figure 4. In this example, the system master is running on a 3.3 V I2C-bus while the slave is connected to a 5 V bus. Both buses run at 100 kHz unless the slave bus is isolated and then the master bus can run at 400 kHz. Master devices can be placed on either bus. 3.3 V 5V VCC SDA SDA0 SDA1 SDA SCL SCL0 SCL1 SCL BUS MASTER 400 kHz PCA9515 bus 0 Fig 4. SLAVE 100 kHz EN bus 1 002aae621 Typical application The PCA9515 is 5 V tolerant so it does not require any additional circuitry to translate between the different bus voltages. When one side of the PCA9515 is pulled LOW by a device on the I2C-bus, a CMOS hysteresis type input detects the falling edge and causes an internal driver on the other side to turn on, thus causing the other side to also go LOW. The side driven LOW by the PCA9515 will typically be at VOL = 0.5 V. In order to illustrate what would be seen in a typical application, refer to Figure 5 and Figure 6. If the bus master in Figure 4 were to write to the slave through the PCA9515, we would see the waveform shown in Figure 5 on Bus 0. This looks like a normal I2C-bus transmission until the falling edge of the 8th clock pulse. At that point, the master releases the data line (SDA) while the slave pulls it LOW through the PCA9515. Because the VOL of the PCA9515 is typically around 0.5 V, a step in the SDA will be seen. After the master has transmitted the 9th clock pulse, the slave releases the data line. On the Bus 1 side of the PCA9515, the clock and data lines would have a positive offset from ground equal to the VOL of the PCA9515. After the 8th clock pulse, the data line will be pulled to the VOL of the slave device that is very close to ground in our example. It is important to note that any arbitration or clock stretching events on Bus 1 require that the VOL of the devices on Bus 1 be 70 mV below the VOL of the PCA9515 (see VOL−VILc in Section 9 “Static characteristics”) to be recognized by the PCA9515 and then transmitted to Bus 0. PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 5 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 9th clock pulse SCL VOL of PCA9515 SDA VOL of master Fig 5. 002aae622 Bus 0 waveform 9th clock pulse SCL VOL of PCA9515 SDA VOL of slave Fig 6. 002aae623 Bus 1 waveform 8. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages with respect to GND. Symbol Parameter Conditions VCC supply voltage I2C-bus Min Max Unit −0.5 +7 V SCL or SDA −0.5 +7 V any pin - 50 mA Vbus voltage range I DC current Ptot total power dissipation - 100 mW Tstg storage temperature −55 +125 °C Tamb ambient temperature −40 +85 °C operating PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 6 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 9. Static characteristics Table 5. Static characteristics VCC = 3.0 V to 3.6 V; GND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Supplies VCC supply voltage 3.0 3.3 3.6 V ICCH HIGH-level supply current both channels HIGH; VCC = 3.6 V; SDAn = SCLn = VCC - 2.3 5 mA ICCL LOW-level supply current both channels LOW; VCC = 3.6 V; one SDA and one SCL = GND, other SDA and SCL open - 2.3 5 mA ICCLc contention LOW-level supply current VCC = 3.6 V; SDAn = SCLn = GND - 2.1 5 mA V Input SCLn; input/output SDAn HIGH-level input voltage VIH 0.7VCC - 5.5 −0.5 - +0.3VCC V −0.5 - +0.4 V VIL LOW-level input voltage [1] VILc contention LOW-level input voltage [1] VIK input clamping voltage II = −18 mA - - −1.2 V ILI input leakage current VI = 3.6 V −1 - +1 µA IIL LOW-level input current SDA, SCL; VI = 0.2 V - - 10 µA VOL LOW-level output voltage IOL = 0 mA or 6 mA 0.47 0.52 0.6 V VOL−VILc difference between LOW-level output and LOW-level input voltage contention guaranteed by design - - 70 mV ILOH HIGH-level output leakage current VO = 3.6 V - - 10 µA 6 7[2] pF input capacitance Ci VI = 3 V or 0 V - Enable input EN VIL LOW-level input voltage −0.5 - +0.8 V VIH HIGH-level input voltage 2.0 - 5.5 V IIL LOW-level input current - 10 30 µA ILI input leakage current −1 - +1 µA Ci input capacitance - 6 7 pF EN; VI = 0.2 V VI = 3.0 V or 0 V [1] VIL specification is for the first LOW level seen by the SDAn/SCLn lines. VILc is for the second and subsequent LOW levels seen by the SDAn/SCLn lines. [2] The SCLn/SDAn Ci is about 200 pF when VCC = 0 V. The PCA9515A should be used in applications where power is secured to the repeater but an active bus remains on either set of SCLn/SDAn pins. PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 7 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 10. Dynamic characteristics Table 6. Dynamic characteristics VCC = 3.0 V to 3.6 V; GND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit tPHL HIGH to LOW propagation delay Figure 7 57 98 170 ns tPLH LOW to HIGH propagation delay Figure 7 33 55 78 ns tTHL HIGH to LOW output transition time Figure 7 - 67 - ns tTLH LOW to HIGH output transition time Figure 7 - 135 - ns tsu set-up time EN to START condition 100 - - ns th hold time EN after STOP condition 100 - - ns [1] [1] The tTLH transition time is specified with loads of 1.35 kΩ pull-up resistance and 7 pF load capacitance, plus an additional 50 pF load capacitance. Different load resistance and capacitance will alter the RC time constant, thereby changing the propagation delay and transition times. 3.3 V input 1.5 V 1.5 V tPHL tPLH 80 % output 1.5 V 20 % 1.5 V 20 % tTHL 0.1 V 3.3 V 80 % VOL tTLH 002aad478 Fig 7. Propagation delay and transition times 11. Test information VCC VCC RL PULSE GENERATOR VI VO DUT CL RT 002aad479 RL = load resistor; 1.35 kΩ. CL = load capacitance includes jig and probe capacitance; 7 pF. RT = termination resistance should be equal to Zo of pulse generators. Fig 8. Test circuit for open-drain outputs PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 8 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 12. Package outline SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 D E A X c y HE v M A Z 5 8 Q A2 A (A 3) A1 pin 1 index θ Lp 1 L 4 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 5.0 4.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 inches 0.069 0.010 0.057 0.004 0.049 0.01 0.019 0.0100 0.014 0.0075 0.20 0.19 0.16 0.15 0.05 0.01 0.01 0.004 0.028 0.012 0.244 0.039 0.028 0.041 0.228 0.016 0.024 θ 8o o 0 Notes 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. Fig 9. REFERENCES OUTLINE VERSION IEC JEDEC SOT96-1 076E03 MS-012 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Package outline SOT96-1 (SO8) PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 9 of 16 PCA9515 NXP Semiconductors I2C-bus repeater TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm D E SOT505-1 A X c y HE v M A Z 5 8 A2 pin 1 index (A3) A1 A θ Lp L 1 4 detail X e w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D(1) E(2) e HE L Lp v w y Z(1) θ mm 1.1 0.15 0.05 0.95 0.80 0.25 0.45 0.25 0.28 0.15 3.1 2.9 3.1 2.9 0.65 5.1 4.7 0.94 0.7 0.4 0.1 0.1 0.1 0.70 0.35 6° 0° Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-04-09 03-02-18 SOT505-1 Fig 10. Package outline SOT505-1 (TSSOP8) PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 10 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 13. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 13.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 13.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 13.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 11 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 13.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 11) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 7 and 8 Table 7. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 ≥ 350 < 2.5 235 220 ≥ 2.5 220 220 Table 8. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 11. PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 12 of 16 PCA9515 NXP Semiconductors I2C-bus repeater maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 11. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 14. Abbreviations Table 9. Abbreviations Acronym Description BiCMOS Bipolar Complementary Metal-Oxide Semiconductor CDM Charged-Device Model DUT Device Under Test ESD ElectroStatic Discharge HBM Human Body Model I2C-bus Inter-Integrated Circuit bus MM Machine Model RC Resistor-Capacitor network SMBus System Management Bus PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 13 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 15. Revision history Table 10. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA9515_9 20090423 Product data sheet - PCA9519_8 Modifications: • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. • • Legal texts have been adapted to the new company name where appropriate. Section 1 “General description”: – 4th paragraph: referenced part type numbers changed from “PCA951x” to “PCA951xA” (excludes PCA9515) – Added new 5th paragraph • Table 5 “Static characteristics”, sub-section “Input SCLn; input/output SDAn”: – Symbol for parameter “input leakage current” changed from “II” to “ILI” – Symbol/parameter changed from “IOH, output HIGH level leakage current” to “ILOH, HIGH-level output leakage current • • Added soldering information Added Section 14 “Abbreviations” PCA9515_8 (9397 750 14097) 20040929 Product data sheet - PCA9515_7 PCA9515_7 (9397 750 12875) 20040624 Product data sheet - PCA9515_6 PCA9515_6 (9397 750 12294) 20031110 Product data 853-2223 30410 dated 2003 Oct 03 PCA9515_5 PCA9515_5 (9397 750 09814) 20020513 Product data 853-2223 28185 dated 2002 May 13 PCA9515_4 PCA9515_4 (9397 750 09512) 20020301 Product data 853-2223 27802 PCA9515_3 PCA9515_3 (9397 750 08127) 20010307 Product specification 853-2223 25782 PCA9515_2 PCA9515_2 (9397 750 07852) 20001201 Product specification 853-2223 25138 PCA9515_1 PCA9515_1 (9397 750 07757) 20001113 Product specification 853-2223 25005 - PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 14 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 16. Legal information 16.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 16.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP B.V. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] PCA9515_9 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 09 — 23 April 2009 15 of 16 PCA9515 NXP Semiconductors I2C-bus repeater 18. Contents 1 2 3 3.1 4 5 5.1 5.2 6 6.1 6.2 7 8 9 10 11 12 13 13.1 13.2 13.3 13.4 14 15 16 16.1 16.2 16.3 16.4 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 I2C-bus systems . . . . . . . . . . . . . . . . . . . . . . . . 4 Application design-in information . . . . . . . . . . 5 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6 Static characteristics. . . . . . . . . . . . . . . . . . . . . 7 Dynamic characteristics . . . . . . . . . . . . . . . . . . 8 Test information . . . . . . . . . . . . . . . . . . . . . . . . . 8 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 9 Soldering of SMD packages . . . . . . . . . . . . . . 11 Introduction to soldering . . . . . . . . . . . . . . . . . 11 Wave and reflow soldering . . . . . . . . . . . . . . . 11 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 11 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 12 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 14 Legal information. . . . . . . . . . . . . . . . . . . . . . . 15 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 15 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Contact information. . . . . . . . . . . . . . . . . . . . . 15 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2009. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 23 April 2009 Document identifier: PCA9515_9