Synthesiser, SMT, 3.15 - 5.55 GHz, 2.5 MHz step. MASY-008215-243000 V2 Features • • • • Full Integration: VCO, PLL, Loop Filter Wide Bandwidth (> 2GHz) Fast Switching (=< 50µs) Low noise: Typ -110 dBc/Hz @ 100kHz offset Description This synthesiser is designed for demanding wide bandwidth applications. The fully integrated design incorporates a VCO, PLL and loop filter in a convenient surface mount package. The lid is fully solder attached to provide optimum electrical shielding. Programming is via 3 Wire SPI (Serial Peripheral Interface.) Actual product finish may vary from illustration Electrical Specification (Applies over the frequency range @ +25 °C, output and input load impedance of 50 ohms. Unless otherwise stated limits & conditions are indicated values.) Parameter Frequency Min Typ 3.15 Max 4.35 Step Size RF Output power 5.55 2.5 0 +3 Units Condition GHz Over TOP - See Note 1. MHz +6 dBm Output Return Loss 12 dB Settling Time 50 µs Output Harmonic -20 -15 dBc Spurious -63 -60 dBc -90 -75 dBc/Hz Offset 1kHz -85 -75 dBc/Hz Offset 10kHz -110 -100 dBc/Hz Offset 100kHz MHz See Note 2. Phase Noise (Noise <1kHz offset dependent upon external reference) External Ref 100 To within ± 10kHz 2.0 2.5 3.3 Volt Out of Lock 0 0.1 0.8 Volt In Lock +23.75 +24 +24.25 Volt 10 15 mA +10 +10.25 Volt 100 150 mA Lock Monitor V PLL DC Supply voltage V PLL DC Current V VCO DC Supply voltage V VCO DC Current +9.75 V cc = +24V V cc = +10 V Note 1: TOP = -40°C ~ +85°C Case operating temperature Note 2: External Reference, 0dBm min input power, with stability of 20 ppm (max) over temperature. Reference phase noise: -98 dBc/Hz @ 10 Hz, -110 dBc/Hz @ 100 Hz, -120 dBc/Hz @ 1 kHz Note 3: Programming 3 Wire SPI (Serial Peripheral Interface) - contact factory for details. 1 M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. M/A-COM makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does M/A-COM assume any liability whatsoever arising out of the use or application of any product(s) or information. • North America Tel: 800.366.2266 / Fax: 978.366.2266 • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 Visit www.macom.com for additional data sheets and product information. Synthesiser, SMT, 3.15 - 5.55 GHz, 2.5 MHz step. MASY-008215-243000 V2 Pin Assignment Pin Number Assignment 2 RF_Out 8 Clock 10 Data 12 LE (Load Enable) 16 LD (Lock Detect) 18 +10V V CC 20 +24V V CC 21 NC (No Connection) 25 REF_IN (Reference Input) All other pins GND Mechanical 2 M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. M/A-COM makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does M/A-COM assume any liability whatsoever arising out of the use or application of any product(s) or information. • North America Tel: 800.366.2266 / Fax: 978.366.2266 • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 Visit www.macom.com for additional data sheets and product information. Synthesiser, SMT, 3.15 - 5.55 GHz, 2.5 MHz step. MASY-008215-243000 V2 Environmental Parameter Min Max Units Case Operating Temperature (TOP ) -40 +85 °C Storage Temperature -45 +120 °C Typical Performance Plots Phase noise at centre frequency 4.35GHz. Frequency Spectrum at centre frequency 4.35GHz. Demonstration Board To enable early system integration and performance verification, this part is available on a demonstration board (pictured.) The demonstration board comes with test results for the on-board unit, with programming software, control cable (PC Printer port) and instructions. For more information about this demonstration system, please contact factory for details. Actual product finish may vary from illustration 3 M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. M/A-COM makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does M/A-COM assume any liability whatsoever arising out of the use or application of any product(s) or information. • North America Tel: 800.366.2266 / Fax: 978.366.2266 • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 Visit www.macom.com for additional data sheets and product information.