MASWSS0117 GaAs SPDT 2.7 V High Power Switch DC - 3.0 GHz Features • • • • • • Rev. V2 Functional Block Diagram Low Voltage Operation: 2.7 V High IP3: +56 dBm Low Insertion Loss: 0.30 dB at 1 GHz High Isolation: 25 dB at 1 GHz SC70 6-Lead Package 0.5 micron GaAs PHEMT Process Description M/A-COM’s MASWSS0117 is a GaAs PHEMT MMIC single pole double throw (SPDT) high power switch in a low cost SC70 6-lead package. The MASWSS0117 is ideally suited for applications where high power, low control voltage, low insertion loss, high isolation, small size and low cost are required. Typical applications are for CDMA handset systems that connect separate transceiver and/or GPS functions to a common antenna, as well as other related handset and general purpose applications. The MASWSS0117 can be used in all systems operating up to 3.0 GHz requiring high power at low control voltage. The MASWSS0117 is fabricated using a 0.5 micron gate length GaAs PHEMT process. The process features full passivation for performance and reliability. Pin Configuration Pin No. Pin Name Description 1 V2 Vcontrol 2 2 RFC RF Common 3 V1 Vcontrol 1 4 RF1 RF Port 1 5 GND RF Ground 6 RF2 RF Port 2 MASWSS0117 orientation in tape Ordering Information1 Part Number Package MASWSS0117 Bulk Packaging MASWSS0117TR 1000 piece reel MASWSS0117TR-3000 3000 piece reel MASWSS0117SMB Sample Test Board MASWSS0117 Device Marking PIN 1 1. Reference Application Note M513 for reel size information. PART NUMBER DATE CODE PIN 6 1 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASWSS0117 GaAs SPDT 2.7 V High Power Switch DC - 3.0 GHz Rev. V2 Electrical Specifications: TA = 25°C, VC = 0 V / 2.7 V, Z0 = 50 Ω 2 Parameter Test Conditions Units Min. Typ. Max. Insertion Loss3 DC – 1 GHz 1 – 2 GHz 2 - 3 GHz dB dB dB — — — 0.30 0.35 0.35 0.65 — — Isolation DC – 1 GHz 1 – 2 GHz 2 - 3 GHz dB dB dB 23 — — 25 19 15 — — — Return Loss DC – 3 GHz dB — 20 — IP3 825 MHz Two Tone, +24 dBm Total Pin, 5 MHz Spacing dBm — 56 — For Cell Band: Two-tone signal input: Tx1 = +22 dBm @ 820 MHz, Tx2 = +22 dBm @ 821 MHz, RX interfere = -23 dBm @ 869 MHz. dBm -99 — For PCS Band: Two-tone signal input: Tx1 = +18 dBm @ 1880 MHz, Tx2 = +18 dBm @ 1881 MHz, RX interfere = -23 dBm @ 1960 MHz. dBm — -94 — P0.1dB 1.0 GHz dBm — 38 — Trise, Tfall 10% to 90% RF, 90% to 10% RF nS — 70 — Ton, Toff 50% control to 90% RF 50% control to 10% RF nS — 100 — Transients In Band mV — 25 — Control Current VC = 2.7 V µA — 5 20 Cross Modulation — 2. For positive voltage control, external DC blocking capacitors are required on all RF ports. 3. Insertion loss can be optimized by varying the DC blocking capacitor value, e.g. 1000 pF for 100 MHz - 1 GHz, 39 pF for 0.5 - 3 GHz. Absolute Maximum Ratings 4,5 Parameter Absolute Maximum Input Power (0.5 - 3 GHz, 3 V Control) +38 dBm Operating Voltage +8.5 volts Operating Temperature -40°C to +85°C Storage Temperature -65°C to +150°C 4. Exceeding any one or combination of these limits may cause permanent damage to this device. 5. M/A-COM does not recommend sustained operation near these survivability limits. Truth Table 6,7,8 V1 V2 ANT– RF1 ANT - RF2 1 0 On Off 0 1 Off On 6. For positive voltage control, external DC blocking capacitors are required on all RF ports. 7. Differential voltage, V (state 1) - V (state 0), must be +2.7 V minimum, but must not exceed 8.5 V. 8. 0 = -5 V to +2.3 V, 1 = -2.3 V to +5 V. 2 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASWSS0117 GaAs SPDT 2.7 V High Power Switch DC - 3.0 GHz Rev. V2 Typical Performance Curves vs. Frequency, 39 pF Insertion Loss Isolation 40 0.6 +25°C +85°C -40°C +25°C +85°C -40°C 0.5 30 0.4 0.3 20 0.2 10 0.1 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0 0.5 1.0 Frequency (GHz) 1.5 2.0 2.5 3.0 Frequency (GHz) Return Loss Qualification 0 +25°C -40°C +85°C -5 Qualified to M/A-COM specification REL-201, Process Flow –2. -10 Handling Procedures -15 Please observe the following precautions to avoid damage: -20 -25 Static Sensitivity -30 -35 0 1 2 3 4 Frequency (GHz) SC-70 Plastic Package† 5 6 Gallium Arsenide Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these devices. 3 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 † Meets JEDEC moisture sensitivity levelon1target requirements. is considering for development. Performance is based specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice.