TVS Diodes P6SMB Series Features: • • • • • • • • • • For surface mounted application in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Excellent clamping capability Fast response time : typically less than 1 ps from 0 V to BV minimum Typical IR less than 1 µA above 10 V High temperature soldering guaranteed : 260°C / 10 seconds at terminals Plastic material used carries 600 watts peak pulse power capability with a 10 × 1,000 µs waveform by 0.01% duty cycle SMB/DO-214AA Dimensions : Inches (Millimetres) Mechanical Data Case Terminals Polarity Standard Packaging Weight : : : : : Moulded plastic Pure tin plated lead free Indicated by cathode band 12 mm tape (EIA STD RS-481) 0.093 g www.element14.com www.farnell.com www.newark.com Page <1> 10/05/12 V1.1 TVS Diodes P6SMB Series Maximum Ratings and Electrical Characteristics Rating at 25°C ambient temperature unless otherwise specified Type Number Symbol Value Peak Power Dissipation at TA = 25°C, Tp = 1 ms (Note 1) PPK Minimum 600 Steady State Power Dissipation PD 3 IFSM 100 A VF 3.5 / 5 V RθJC RθJA 10 55 °C / W TJ, TSTG -65 to + 150 °C Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 2, 3) - Unidirectional Only Maximum Instantaneous Forward Voltage at 50 A for Unidirectional Only (Note 4) Typical Thermal Resistance (Note 5) Operating and Storage Temperature Range Units W Notes : 1. Non-repetitive current pulse and derated above TA = 25°C 2. Mounted on 5 mm2 (0.013 mm thick) copper pads to each terminal 3. 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minutes maximum 4. VF = 3.5 V on P6SMB6.8 thru P6SMB91 devices and VF = 5 V on P6SMB100 thru P6SMB220 devices 5. Measured on P.C.B. with 0.27 × 0.27 Inch (7 × 7 mm) copper pad areas Devices for bipolar applications 1. For bidirectional use C or CA suffix for types P6SMB6.8 through types P6SMB220A 2. Electrical characteristics apply in both directions Ratings and Characteristic Curves Pulse Derating Curve Peak Pulse Power (PPP) or Current (IPPM) Derating In Percentage, % PPPM, Peak Pulse Power, KW Peak Pulse Power Rating Curve tp, Pulse Width, Seconds TA Ambient Temperature, °C www.element14.com www.farnell.com www.newark.com Page <2> 10/05/12 V1.1 TVS Diodes P6SMB Series Ratings and Characteristic Curves Maximum Non-Repetitive Forward Surge Current Unidirectional Only IFSM, Peak Forward Surge Current, Amperes Peak Pulse Current - % Clamping Power Pulse Waveform t, Time, ms Number of Cycles at 60 Hz CJ, Junction Capacitance (pF) Typical Junction Capacitance (Unidirectional) V (BR), Breakdown Voltage Volts www.element14.com www.farnell.com www.newark.com Page <3> 10/05/12 V1.1 TVS Diodes P6SMB Series Electrical Characteristics (TA = 25°C unless otherwise noted) Breakdown Voltage Maximum Test Stand-Off Reverse Device Device Current Voltage Leakage Marking VBR (Volts) (Note 1) at IT VWM at VWM Code (mA) (Volts) ID (µA) Unidirectional Bidirectional Minimum Maximum Maximum Peak Pulse Current IRSM (Note 2) (Amperes) Maximum Maximum Clamping Temperature Voltage Coefficient at IPPM of VBR VC (Volts) (% / °C) P6SMB100A P6SMB100CA MXJ 95 105 85.5 5 4.5 137 0.106 P6SMB10A P6SMB10CA KPJ 9.5 10.5 8.55 10 43 14.5 0.073 P6SMB150A P6SMB150CA NKJ 143 158 128 3 207 0.108 P6SMB18A P6SMB18CA LEJ 17.1 18.9 15.3 25 25.2 0.088 P6SMB200A P6SMB200CA NTJ 190 210 171 2.2 274 0.108 P6SMB22A P6SMB22CA LKJ 20.9 23.1 18.8 20 30.6 0.092 P6SMB27A P6SMB27CA LPJ 25.7 28.4 23.1 16.8 37.5 0.096 P6SMB33A P6SMB33CA LTJ 31.4 34.7 28.2 13.8 45.7 0.098 P6SMB36A P6SMB36CA LVJ 34.2 37.8 30.8 12.6 49.9 0.099 P6SMB39A P6SMB39CA LXJ 37.1 41 33.3 11.6 53.9 0.1 P6SMB47A P6SMB47CA MEJ 44.7 49.4 40.2 9.7 64.8 0.101 - P6SMB62CA MMJ 58.9 65.1 53 7.4 85 P6SMB68A P6SMB68CA MPJ 64.6 71.4 58.1 6.8 92 P6SMB6V8A P6SMB6V8CA KEJ 6.45 7.14 60 10.5 1 10 5.8 5 1,000 0.104 0.057 Notes: 1. VBR measured after IT applied for 300 µs, IT = square wave pulse or equivalent 2. Surge current waverform and derate 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled 4. For bidirectional use C or CA suffix for types P6SMB6.8 through P6SMB220A 5. All terms and symbols are consistent with ANSI / IEEE C62.35 Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012. www.element14.com www.farnell.com www.newark.com Page <4> 10/05/12 V1.1