MC74VHC1GT66 SPST (NO) Normally Open Analog Switch Features • • • • • • • High Speed: tPD = 20 ns (Typ) at VCC = 5 V Low Power Dissipation: ICC = 1.0 mA (Max) at TA = 25°C Diode Protection Provided on Inputs and Outputs Improved Linearity and Lower ON Resistance over Input Voltage http://onsemi.com MARKING DIAGRAMS 5 SC−88A DF SUFFIX CASE 419A 5 1 M The MC74VHC1GT66 is a Single Pole Single Throw (SPST) analog switch. It achieves high speed propagation delays and low ON resistances while maintaining low power dissipation. This bilateral switch controls analog and digital voltages that may vary across the full power−supply range (from VCC to GND). The MC74VHC1GT66 is compatible in function to a single gate of the High Speed CMOS MC74VHCT4066 and the metal−gate CMOS MC14066. The device has been designed so that the ON resistances (RON) are much lower and more linear over input voltage than RON of the metal−gate CMOS or High Speed CMOS analog switches. The ON/OFF Control input is compatible with TTL−type input thresholds allowing the device to be used as a logic−level translator from 3 V CMOS logic to 5 V CMOS logic or from 1.8 V CMOS logic to 3 V CMOS logic while operating at the high−voltage power supply. The input protection circuitry on this device allows overvoltage tolerance on the input, which provides protection when voltages of up to 7 V are applied, regardless of the supply voltage. This allows the MC74VHC1GT66 to be used to interface 5 V circuits to 3 V circuits. VE MG G 1 TSOP−5 DT SUFFIX CASE 483 5 1 5 VE MG G 1 VE = Device Code M = Date Code* W = Work Week G = Pb−Free Package (Note: Microdot may be in either location) *Date Code orientation and/or position may vary depending upon manufacturing location. On/Off Control Input Has OVT Chip Complexity: FETs = 11; Equivalent Gates = 3 Pb−Free Packages are Available PIN ASSIGNMENT 1 IN/OUT XA 2 OUT/IN YA 3 GND 4 ON/OFF CONTROL 5 VCC FUNCTION TABLE On/Off Control Input State of Analog Switch L H Off On ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. © Semiconductor Components Industries, LLC, 2011 August, 2011 − Rev. 15 1 Publication Order Number: MC74VHC1GT66/D MC74VHC1GT66 IN/OUT XA 1 OUT/IN YA 2 GND 3 5 VCC 4 ON/OFF CONTROL (SC−88A, TSOP−5) Figure 1. Pinout Diagram ON/OFF CONTROL X1 1 1 U U IN/OUT XA OUT/IN YA Figure 2. Logic Symbol MAXIMUM RATINGS Symbol Characteristics Value Unit VCC DC Supply Voltage −0.5 to +7.0 V VIN DC Input Voltage −0.5 to +7.0 V VIS Analog Output Voltage −0.5 to 7.0 V IIK Input Diode Current −20 mA ICC DC Supply Current, VCC and GND +25 mA *65 to )150 °C 260 °C TSTG Storage Temperature Range TL Lead Temperature, 1 mm from Case for 10 Seconds TJ Junction Temperature Under Bias qJA Thermal Resistance PD Power Dissipation in Still Air at 85°C MSL Moisture Sensitivity FR Flammability Rating VESD ILatchup ESD Withstand Voltage Latchup Performance )150 °C SC70−5 (Note 1) SOT23−5 350 230 °C/W SC70−5 SOT23−5 150 200 mW Level 1 Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) u2000 u200 N/A V Above VCC and Below GND at 125°C (Note 5) $500 mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2−ounce copper trace with no air flow. 2. Tested to EIA/JESD22−A114−A. 3. Tested to EIA/JESD22−A115−A. 4. Tested to JESD22−C101−A. 5. Tested to EIA/JESD78. http://onsemi.com 2 MC74VHC1GT66 RECOMMENDED OPERATING CONDITIONS Symbol Characteristics Min Max Unit VCC DC Supply Voltage 2.0 5.5 V VIN Digital Input Voltage GND 5.5 V VIS Analog Input Voltage GND VCC V TA Operating Temperature Range −55 +125 °C 0 0 100 20 ns/V tr , tf Input Rise and Fall Time VCC = 3.3 V ± 0.3 V VCC = 5.0 V ± 0.5 V 90 419,300 47.9 100 178,700 20.4 110 79,600 9.4 120 37,000 4.2 130 17,800 2.0 140 8,900 1.0 TJ = 80 ° C 117.8 TJ = 90 ° C 1,032,200 TJ =100° C 80 FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ =110 ° C Time, Years TJ =120° C Time, Hours TJ = 130 ° C Junction Temperature °C NORMALIZED FAILURE RATE Device Junction Temperature versus Time to 0.1% Bond Failures 1 1 10 100 1000 TIME, YEARS Figure 3. Failure Rate vs. Time Junction Temperature http://onsemi.com 3 MC74VHC1GT66 DC ELECTRICAL CHARACTERISTICS Symbol Parameter Test Conditions VIH Minimum High−Level Input Voltage ON/OFF Control Input RON = Per Spec VIL Maximum Low−Level Input Voltage ON/OFF Control Input RON = Per Spec IIN Maximum Input Leakage Current ON/OFF Control Input ICC TA = 25°C VCC (V) Min 3.0 4.5 5.5 1.2 2.0 2.0 TA ≤ 85°C Max Min Max 1.2 2.0 2.0 −55°C ≤ TA ≤ 125°C Min Max Unit V 1.2 2.0 2.0 V 3.0 4.5 5.5 0.53 0.8 0.8 0.53 0.8 0.8 0.53 0.8 0.8 VIN = VCC or GND 0 to 5.5 ±0.1 ±1.0 ±1.0 mA Maximum Quiescent Supply Current VIN = VCC or GND VIO = 0 V 5.5 1.0 20 40 mA ICCT Quiescent Supply Current ON/OFF Control at 3.4 V 5.5 1.35 1.5 1.65 mA RON Maximum ”ON” Resistance VIN = VIH VIS = VCC or GND |IIS| ≤ 10 mA (Figure 4) 3.0 4.5 5.5 60 45 40 70 50 45 100 60 55 W IOFF Maximum Off−Channel Leakage Current VIN = VIL VIS = VCC or GND Switch Off (Figure 5) 5.5 0.1 0.5 1.0 mA AC ELECTRICAL CHARACTERISTICS Cload = 50 pF, Input tr/tf = 3.0 ns Symbol Parameter VCC (V) TA = 25°C Typ Max Max Unit 1 0.6 0.6 0.6 5 2 1 1 6 3 1 1 7 4 2 1 ns 2.0 3.0 4.5 5.5 32 28 24 20 40 35 30 25 45 40 35 30 50 45 40 35 ns 2.0 3.0 4.5 5.5 32 28 24 20 40 35 30 25 45 40 35 30 50 45 40 35 ns ON/OFF Control Input 0.0 3 10 10 10 pF Control Input = GND Analog I/O Feedthrough 5.0 4 4 10 10 10 10 10 10 Maximum Propagation Delay, Input X to Y YA = Open tPLZ, tPHZ Maximum Propagation Delay, ON/OFF Control to Analog Output RL = 1000 W tPZL, tPZH Maximum Propagation Delay, ON/OFF Control to Analog Output RL = 1000 W CIN Maximum Input Capacitance (Figures 7, 14) (Figures 8, 15) (Figures 8, 15) Min Max −55°C ≤ TA ≤ 125°C 2.0 3.0 4.5 5.5 Test Conditions tPLH, tPHL Min TA ≤ 85°C Min Typical @ 25°C, VCC = 5.0 V CPD 18 Power Dissipation Capacitance (Note 6) pF 6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no−load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 4 MC74VHC1GT66 ADDITIONAL APPLICATION CHARACTERISTICS (Voltages Referenced to GND Unless Noted) Symbol Parameter Test Conditions VCC Limit 25°C Unit BW Maximum On−Channel Bandwidth or Minimum Frequency Response (Figure 10) fin = 1 MHz Sine Wave Adjust fin voltage to obtain 0 dBm at VOS Increase fin = frequency until dB meter reads −3 dB RL = 50 W 3.0 4.5 5.5 150 175 180 MHz ISOoff Off−Channel Feedthrough Isolation (Figure 11) fin = Sine Wave Adjust fin voltage to obtain 0 dBm at VIS fin = 10 kHz, RL = 600 W 3.0 4.5 5.5 −80 −80 −80 dB Feedthrough Noise Control to Switch (Figure 12) Vin ≤ 1 MHz Square Wave (tr = tf = 2ns) 3.0 4.5 5.5 45 60 130 mVPP Total Harmonic Distortion (Figure 13) fin = 1 kHz, RL = 10 kW THD = THDMeasured − THDSource VIS = 3.0 VPP sine wave VIS = 5.0 VPP sine wave NOISEfeed THD RL = 600 W % 3.3 5.5 0.30 0.15 PLOTTER POWER SUPPLY − COMPUTER DC PARAMETER ANALYZER + VCC 1 VCC VCC 5 1 2 5 VIH 2 3 VCC 4 VIL A 3 Figure 4. On Resistance Test Set−Up VCC 4 Figure 5. Maximum Off−Channel Leakage Current Test Set−Up VCC A N/C 1 5 2 3 VCC 1 TEST POINT VIH 4 2 3 Figure 6. Maximum On−Channel Leakage Current Test Set−Up 5 VIH 4 Figure 7. Propagation Delay Test Set−Up http://onsemi.com 5 MC74VHC1GT66 Switch to Position 2 when testing tPLZ and tPZL Switch to Position 1 when testing tPHZ and tPZH TEST POINT VCC VCC VCC 1 1 RL 2 2 1 VCC A 5 CL * 3 N/C 1 N/C 2 4 5 3 2 4 *Includes all probe and jig capacitance. Figure 8. Propagation Delay Output Enable/Disable Test Set−Up Figure 9. Power Dissipation Capacitance Test Set−Up VOS VIS VCC 0.1 mF fin 1 VOS VCC 0.1 mF fin 5 1 2 dB Meter 2 3 dB Meter 4 RL 3 *Includes all probe and jig capacitance. Figure 11. Off−Channel Feedthrough Isolation Test Set−Up To Distortion Meter (VCC)/2 (VCC)/2 RL IS VIS VCC RL 1 4 *Includes all probe and jig capacitance. Figure 10. Maximum On−Channel Bandwidth Test Set−Up VOS 5 5 V IN RL v 1 MHz fin 1 5 VOS 2 t r + t + 2 ns 3 VIH 2 f 4 VCC 0.1 mF 3 GND *Includes all probe and jig capacitance. VIH 4 *Includes all probe and jig capacitance. Figure 12. Feedthrough Noise, ON/OFF Control to Analog Out, Test Set−Up Figure 13. Total Harmonic Distortion Test Set−Up http://onsemi.com 6 MC74VHC1GT66 XA VCC 1.5 V 1.5 V tPLH YA tPHL VOH 50% VCC VOL Figure 14. Propagation Delay, Analog In to Analog Out Waveforms tr tf 90% Control 10% 1.5 V VIH tPLZ tPZL 50% VCC 10% Analog Out 90% 50% VCC tPHZ tPZH High Impedance VOL VOH High Impedance Figure 15. Propagation Delay, ON/OFF Control ORDERING INFORMATION Device Package M74VHC1GT66DFT1G SC−88A (Pb−Free) MC74VHC1GT66DFT2 SC−88A M74VHC1GT66DFT2G SC−88A (Pb−Free) MC74VHC1GT66DTT1 TSOP−5 M74VHC1GT66DTT1G TSOP−5 (Pb−Free) Shipping† 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 7 MC74VHC1GT66 PACKAGE DIMENSIONS SC−88A (SC−70−5/SOT−353) CASE 419A−02 ISSUE K A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A−01 OBSOLETE. NEW STANDARD 419A−02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. G 5 4 −B− S 1 2 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) M B M N INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 J C K H SOLDERING FOOTPRINT* 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 8 mm Ǔ ǒinches MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 MC74VHC1GT66 PACKAGE DIMENSIONS TSOP−5 CASE 483−02 ISSUE H D 5X NOTE 5 2X 0.10 T 2X 0.20 T NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. 0.20 C A B M 5 1 4 2 L 3 B S K DETAIL Z G A DIM A B C D G H J K L M S DETAIL Z J C 0.05 SEATING PLANE H T SOLDERING FOOTPRINT* 0.95 0.037 MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74VHC1GT66/D