MD- / MDS-149 Double-Balanced Mixer, 10 - 1500 MHz Features Rev. V4 FP-2 (MD-149) • • • • • • Over Two-Decade Frequency Range Conversion Loss: 6 dB Typical Midband LO-RFIsolation: 40 dB Typical Midband Fully Hermetic Package Impedance: 50 Ohms Nominal Maximum Input Power: 300 mW Max, Derated to 85°C @ 3.2 mW/°C • IF Port Current: 50 mA Max. • MIL-STD-883 Screening Available Description Transformers convert the LO and RF paths to balanced lines connecting to a medium barrier, Schottky diode ring quad. These transformers help provide excellent isolation between ports. Conversion loss is low. The direct connection of the IF port to the diode quad allows these mixers to be used as phase detectors and bi-phase modulators. SF-1 (MDS-149) Pin Configuration (MD-149) Pin No. Function Pin No. Function 1 GND 5 LO 2 GND 6 GND 3 GND 7 GND 4 IF 8 RF Pin Configuration (MDS-149) Pin No. Function Pin No. Function 1 GND 3 LO 2 IF 4 RF 1 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.4155721 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MD- / MDS-149 Double-Balanced Mixer, 10 - 1500 MHz Rev. V4 Electrical Specifications1: TA = -55°C to +85°C Parameter Test Conditions Frequency Units Min Typ Max Frequency Range RF, LO Ports IF Port 10 - 1500 DC - 1500 MHz MHz — — — 10 - 1000 MHz 1000 - 1500 MHz dB dB — — — — 7.5 10 LO to RF 10 - 100 MHz 100 - 1000 MHz 1000 - 1500 MHz dB dB dB 35 30 20 — — — — — — LO to IF 10 - 100 MHz 100 - 1000 MHz 1000 - 1500 MHz dB dB dB 35 20 12 — — — — — — RF to IF 10 - 100 MHz 100 - 1000 MHz 1000 - 1500 MHz dB dB dB 30 18 8 — — — — — — DC Polarity Negative — — — — — DC Offset — — mV — <4 — RF Input 1 dB Compression 1 dB Desensitization — — dBm dBm — — 0 -2.0 — — SSB Noise Figure Within 1 dB of Conversion Loss Max — — — — — Typical Two-Tone IM Ratio with a –10 dBm input, each input, 25 MHz and 35 MHz IF 100-500 MHz 500-1000 MHz 1000-1500 MHz dB dB dB — — — 48 43 35 — — — Conversion Loss Isolation 1. All specifications apply when operated at +7 dBm available LO power with 50 ohm source and load impedance. Bottom View of SF-1 4X .016 ± .002 .506 4X .099 ± .010 6X .050 (+.020/-.000) Typical Performance Curves .385 Ref .220 .381 .165 .510 Ref .430 .367 .305 .143 .205 .080 .000 .002 .002 .000 2 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.4155721 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MD- / MDS-149 Double-Balanced Mixer, 10 - 1500 MHz Rev. V4 Typical Performance Curves Ordering Information Part Number Package MD-149 PIN FP-2 MDS-149 PIN SF-1 3 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.4155721 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice.