NCP5351 4 A Synchronous Buck Power MOSFET Driver The NCP5351 is a dual MOSFET gate driver optimized to drive the gates of both high−side and low−side Power MOSFETs in a Synchronous Buck converter. The NCP5351 is an excellent companion to multiphase controllers that do not have integrated gate drivers, such as ON Semiconductor’s CS5323, CS5305 or CS5307. This architecture provides a power supply designer the flexibility to locate the gate drivers close to the MOSFETs. The 4.0 A drive capability makes the NCP5351 ideal for minimizing switching losses in MOSFETs with large input capacitance. Optimized internal, adaptive nonoverlap circuitry further reduces switching losses by preventing simultaneous conduction of both MOSFETs. The floating top driver design can accommodate MOSFET drain voltages as high as 25 V. Both gate outputs can be driven low, and supply current reduced to less than 25 mA, by applying a low logic level to the Enable (EN) pin. An undervoltage lockout function ensures that both driver outputs are low when the supply voltage is low, and a thermal shutdown function provides the IC with overtemperature protection. The NCP5351 is pin−to−pin compatible with the SC1205 and is available in a standard SO−8 package and thermally enhanced DFN10. http://onsemi.com MARKING DIAGRAMS 8 SO−8 D SUFFIX CASE 751 8 1 5351 ALYW G 1 1 DFN10 MN SUFFIX CASE 485C 1 A L Y W G 5351 ALYWG G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) Features • • • • • • • • • • • 4.0 A Peak Drive Current Rise and Fall Times < 15 ns Typical into 6000 pF Propagation Delay from Inputs to Outputs < 20 ns Adaptive Nonoverlap Time Optimized for Large Power MOSFETs Floating Top Driver Accommodates Applications Up to 25 V Undervoltage Lockout to Prevent Switching when the Input Voltage is Low Thermal Shutdown Protection Against Overtemperature < 1.0 mA Quiescent Current − Enabled 25 mA Quiescent Current − Disabled Internal TG to DRN Pulldown Resistor Prevents HV Supply−Induced Turn On of High−Side MOSFET Pb−Free Package is Available PIN CONNECTIONS DRN 1 SO−8 8 PGND TG BST BG VS CO EN 1 DRN TG N/C BST CO DFN10 10 GND BG N/C VS EN ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet. © Semiconductor Components Industries, LLC, 2010 February, 2010 − Rev. 13 1 Publication Order Number: NCP5351/D NCP5351 BST Level Shifter + − VS + − TG 4.25 V DRN Delay Nonoverlap Control + − EN 4.0 V Delay Thermal Shutdown VS BG CO PGND Figure 1. Block Diagram Table 1. Input−Output Truth Table EN CO DRN TG BG L X X L L H L < 3.0 V L H H H < 3.0 V H L H L > 5.0 V L L H H > 5.0 V H L VCO tpdlTG tpdlBG VTG−VDRN tfTG trTG tpdhTG (Nonoverlap) VBG trBG tfBG tpdhBG (Nonoverlap) VDRN 4.0 V Figure 2. Timing Diagram http://onsemi.com 2 NCP5351 PACKAGE PIN DESCRIPTION Pin Number SO−8 DFN−10 Pin Symbol 1 1 DRN 2 2 TG Driver output to the high−side MOSFET gate. 3 4 BST Bootstrap supply voltage input. In conjunction with a Schottky diode to VS, a 0.1 mF to 1.0 mF ceramic capacitor connected between BST and DRN develops supply voltage for the high−side driver (TG). 4 5 CO Logic level control input produces complementary output states − no inversion at TG; inversion at BG. − 3, 8 N/C Not Connected. 5 6 EN Logic level enable input forces TG and BG low, and supply current to 10 mA when EN is low. 6 7 VS Power supply input. A 0.1 mF to 1.0 mF ceramic capacitor should be connected from this pin to PGND. 7 9 BG Driver output to the low−side (synchronous rectifier) MOSFET gate. 8 − PGND Ground. − 10 GND Ground. Description The switching node common to the high and low−side FETs. The high−side (TG) driver and supply (BST) are referenced to this pin. http://onsemi.com 3 NCP5351 MAXIMUM RATINGS − SO−8 Rating Value Unit Operating Junction Temperature, TJ Internally Limited °C Package Thermal Resistance: SO−8 Junction−to−Case, RqJC Junction−to−Ambient, RqJA 45 165 °C/W °C/W −65 to 150 °C 230 peak 260 peak °C 1 − Storage Temperature Range, TS Lead Temperature Soldering: Reflow: (SMD styles only) (Note 1) Pb−Free MSL Rating Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. NOTE: This device is ESD sensitive. Use standard ESD precautions when handling. 1. 60 seconds maximum above 183°C. MAXIMUM RATINGS − DFN−10 Rating Symbol Value Unit Thermal Resistance, Junction−to−Air RJA 68.5 °C/W Operating Ambient Temperature Range TA −30 to 85 °C VESD > 2500 > 150 V Moisture Sensitivity MSL Level 1 Storage Temperature Range Tstg −55 to 150 °C Junction Operating Temperature TJ −30 to 125 °C ESD Withstand Voltage Human Body Model (Note 2) Machine Model (Note 2) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 2. This device series contains ESD protection and exceeds the following tests: Human Body Model, 100 pF discharge through a 1.5 kW following specification JESD22/A114. Machine Model, 200 pF discharged through all pins following specification JESD22/A115. Latchup as per JESD78 Class II: > 100 mA. MAXIMUM RATINGS Pin Symbol Pin Name VMAX VMIN ISOURCE ISINK VS Main Supply Voltage Input 6.3 V −0.3 V NA 4.0 A Peak (< 100 ms) 250 mA DC BST Bootstrap Supply Voltage Input 25 V wrt/PGND 6.3 V wrt/DRN −0.3 V wrt/DRN NA 4.0 A Peak (< 100 ms) 250 mA DC DRN Switching Node (Bootstrap Supply Return) 25 V −1.0 V DC −5.0 V for 100 ns −6.0 V for 20 ns 4.0 A Peak (< 100 ms) 250 mA DC NA TG High−Side Driver Output (Top Gate) 25 V wrt/PGND 6.3 V wrt/DRN −0.3 V wrt/DRN 4.0 A Peak (< 100 ms) 250 mA DC 4.0 A Peak (< 100 ms) 250 mA DC BG Low−Side Driver Output (Bottom Gate) 6.3 V −0.3 V 4.0 A Peak (< 100 ms) 250 mA DC 4.0 A Peak (< 100 ms) 250 mA DC CO TG & BG Control Input 6.3 V −0.3 V 1.0 mA 1.0 mA EN Enable Input 6.3 V −0.3 V 1.0 mA 1.0 mA PGND Ground 0V 0V 4.0 A Peak (< 100 ms) 250 mA DC NA NOTE: All voltages are with respect to PGND except where noted. http://onsemi.com 4 NCP5351 ELECTRICAL CHARACTERISTICS (0°C < TJ < 125°C; VS = 5.0 V; 4.0 V < VBST < 25 V; VEN = VS; unless otherwise noted) Test Conditions Parameter Min Typ Max Unit DC OPERATING SPECIFICATIONS POWER SUPPLY VS Quiescent Current, Operating VCO = 0 V, 4.5 V; No output switching − 1.0 − mA VBST Quiescent Current, Operating VCO = 0 V, 4.5 V; No output switching − 50 − mA Quiescent Current, Non−Operating VEN = 0 V; VCO = 0 V, 4.5 V − − 25 mA Undervoltage Lockout Start Threshold CO = 0 V 4.05 4.25 4.48 V Hysteresis CO = 0 V − 275 − mV CO INPUT CHARACTERISTICS High Threshold − 2.0 − − V Low Threshold − − − 0.8 V − 0 1.0 mA 2.0 − − V Input Bias Current 0 < VCO < VS EN INPUT CHARACTERISTICS High Threshold Both outputs respond to CO Low Threshold Both outputs are low, independent of CO − − 0.8 V Input Bias Current 0 < VEN < VS − 0 10 mA THERMAL SHUTDOWN Overtemperature Trip Point − − 170 − °C Hysteresis − − 30 − °C − − 4.0 − A HIGH−SIDE DRIVER Peak Output Current Output Resistance (Sourcing) Duty Cycle < 2.0%, Pulse Width < 100 ms, TJ = 125°C, VBST − VDRN = 4.5 V, VTG = 4.0 V + VDRN − 0.5 − W Output Resistance (Sinking) Duty Cycle < 2.0%, Pulse Width < 100 ms, TJ = 125°C, VBST − VDRN = 4.5 V, VTG = 0.5 V + VDRN − 0.42 − W − 4.0 − A LOW−SIDE DRIVER Peak Output Current − Output Resistance (Sourcing) Duty Cycle < 2.0%, Pulse Width < 100 ms, TJ = 125°C, VS = 4.5 V, VBG = 4.0 V − 0.6 − W Output Resistance (Sinking) Duty Cycle < 2.0%, Pulse Width < 100 ms, TJ = 125°C, VS = 4.5 V, VBG = 0.5 V − 0.42 − W http://onsemi.com 5 NCP5351 ELECTRICAL CHARACTERISTICS (continued) (0°C < TJ < 125°C; VS = 5.0 V; 4.0 V < VBST < 25 V; VEN = VS, CLOAD = 5.7 nF; unless otherwise noted.) Parameter Test Conditions Min Typ Max Unit AC OPERATING SPECIFICATIONS HIGH−SIDE DRIVER Rise Time VBST − VDRN = 5.0 V, TJ = 125°C − 8.0 16 ns Fall Time VBST − VDRN = 5.0 V, TJ = 125°C − 14 21 ns Propagation Delay Time, TG Going High (Nonoverlap Time) VBST − VDRN = 5.0 V, TJ = 125°C 30 45 60 ns Propagation Delay Time, TG Going Low VBST − VDRN = 5.0 V, TJ = 125°C − 18 37 ns Rise Time TJ = 125°C − 10 15 ns Fall Time TJ = 125°C − 12 20 ns Propagation Delay Time, BG Going High (Non−Overlap Time) TJ = 125°C 25 55 80 ns Propagation Delay Time, BG Going Low TJ = 125°C − 10 18 ns VS Rising EN = VS, CO = 0 V, dVS/dt > 1.0 V/ms, from 4.0 V to 4.5 V, time to BG > 1.0 V, TJ = 125°C − 30 − ms VS Falling EN = VS, CO = 0 V, dVS/dt < −1.0 V/ms, from 4.5 V to 4.0 V, time to BG < 1.0 V, TJ = 125°C − 500 − ms LOW−SIDE DRIVER UNDERVOLTAGE LOCKOUT http://onsemi.com 6 PWRGD 3.3 V Figure 3. Application Diagram VID2 VID3 VID4 PWRLS VFFB SS PWRGD DRVON SGND Near Socket VFFB Connection 8 7 6 5 4 3 2 1 32 9 VID2 VID3 VID4 31 10 VID5 VID0 VID1 30 NCP5314 11 ENABLE 29 12 3.3 V 28 13 12 V 27 14 5.0 V 25 26 NTC Near Inductor 17 18 19 20 21 22 23 ILIM 24 ROSC VCC GATE1 GATE2 GATE3 GATE4 GND VID1 VID0 VID5 ENABLE CS2N CS2P CS1N CS1P SGND VDRP VFB COMP CS4N CS4P CS3N CS3P 7 15 http://onsemi.com 16 ATX 12 V BST TG DRN PGND BG NCP5351 6 VS 4 CO 5 EN 8 BST TG DRN PGND BG NCP5351 6 VS 4 CO 5 EN 8 BST TG DRN PGND BG NCP5351 6 VS 4 CO 5 EN 8 BST TG DRN PGND BG NCP5351 6 VS 4 CO 5 EN 8 3 2 1 7 3 2 1 7 3 2 1 7 3 2 1 7 + + GND VCORE NCP5351 NCP5351 APPLICATIONS INFORMATION Theory Of Operation the drain (switch node) is sampled and the BG is disabled for a fixed delay time (tpdhBG) after the drain drops below 4 V, thus eliminating the possibility of shoot−through. When the bottom MOSFET is turning off, TG is disabled for a fixed delay (tpdhTG) after BG drops below 2.0 V. (See Figure 2 for complete timing information). Enable Pin The Enable Pin (EN) is controlled by a logic level input. With a logic level high on the EN pin, the output states of the drivers are controlled by applying a logic level voltage to the CO pin. With a logic level low both gates are forced low. By bringing both gates low when disabling, the output voltage is prevented from ringing below ground, which could potentially cause damage to the microprocessor or the device being powered. Layout Guidelines When designing any switching regulator, the layout is very important for proper operation. The designer should follow some simple layout guidelines when incorporating gate drivers in their designs. Gate drives experience high di/dt during switching and the inductance of gate drive traces should be minimized. Gate drive traces should be kept as short and wide as practical and should have a return path directly below the gate trace. The use of a ground plane is a desirable way to return ground signals. Also, component location will make a difference. The boost and the VS capacitor are the most critical and should be placed as close as possible to the driver IC pins, as shown in Figure 4(a), C21 and C17. Undervoltage Lockout The TG and BG are held low until VS reaches 4.25 V during startup. The CO pin takes control of the gates’ states when the VS threshold is exceeded. If VS decreases 300 mV below threshold, the output gate will be forced low and remain low until VS rises above startup threshold. Adaptive Nonoverlap The Adaptive Nonoverlap prevents a condition where the top and bottom MOSFETs conduct at the same time and short the input supply. When the top MOSFET is turning off, 5V 12 V D32 BAT54 C21 1.0 mF 4 CO 3 BST 2 TG 1 DRN GATE1 U3 Gate Driver Q7 80NO2 5 EN 6 VS 7 BG 8 PGND NCP5351 DRVON R33 C17 2.2 1.0 mF (a) (b) Figure 4. Proper Layout (a), Component Selection (b) http://onsemi.com 8 Q9 80NO2 NCP5351 TYPICAL PERFORMANCE CHARACTERISTICS COM EN CO HOT BST NCP5351 VS Measurement R1 1.0 k TG BG C1 C2 C3 C4 1.0 mF 1.0 mF 100 nF 100 nF PGND DRN −5.0 V R2* 0.108 W *Applied after power up and input. Conditions: BST − DRN = 5.0 V; Room Temperature; Oscilloscope referenced to VS (5.0 V). Figure 5. Top Gate Sinking Current from 0.108 W Input Pulse 50 ns 0V −5.0 V 0V TG −5.0 V CO 0V −5.0 V COM HOT VS EN BST C2 1.0 mF Figure 7. Bottom Gate Sinking Current from 0.108 W Input Pulse 50 ns −3.5 V −4.5 V http://onsemi.com 9 R2* 0.108 W C1 1.0 mF *Applied after power up and input. Conditions: VS = 5.0 V; Room Temperature; CO = 0 V. Figure 8. Bottom Gate Sinking TG BG DRN PGND CO −5.0 V DRN −3.5 V −4.5 V 0V BG −0.5 V NCP5351 R3 50 R1 1.0 k Measurement Figure 6. Top Gate Sinking NCP5351 TYPICAL PERFORMANCE CHARACTERISTICS +5.0 V EN CO BST NCP5351 VS TG BG PGND DRN + − C1 C2 C3 C4 1.0 mF 1.0 mF 100 nF 100 nF Measurement R1 1.0 k R2* 0.108 W *Applied after power up and input. Conditions: VS = 5.0 V; Room Temperature; DRN = 0 V. Figure 9. Bottom Gate Sourcing Current into 0.108 W CO BG Input Pulse 50 ns 0 +5.0 V 0V 0 Figure 10. Bottom Gate Sourcing +5.0 V EN CO BST NCP5351 VS TG BG PGND DRN + − C1 C2 C3 C4 1.0 mF 1.0 mF 100 nF 100 nF Measurement R1 1.0 k R2* 0.108 W *Applied after power up and input. Conditions: BST − DRN = 5.0 V; Room Temperature; DRN = 0 V. Figure 11. Top Gate Sourcing Current into 0.108 W CO TG Input Pulse 50 ns 0 +5.0 V 0V 0 Figure 12. Top Gate Sourcing http://onsemi.com 10 NCP5351 TYPICAL PERFORMANCE CHARACTERISTICS +5.0 V EN CO PGND BST TG DRN BG C4 100 nF Measurements Gated Pulse Burst (2) R2 50 VS NCP5351 R1 1.0 k + − Input Pulse C2 10 mF C1 10 mF C3 100 nF + − tpdlBG tpdlTG 4.0 V DRN CO TG BG tpdhTG (non−overlap) tpdhBG (non−overlap) Figure 13. Nonoverlap Test Configuration Conditions: VS = 5.0 V; BST − DRN = 5.0 V; CLOAD = 5.7 nF; Room Temperature. Conditions: VS = 5.0 V; BST − DRN = 5.0 V; CLOAD = 5.7 nF; Room Temperature. Figure 14. Top Gate Rise Time Figure 15. Top Gate Fall Time http://onsemi.com 11 NCP5351 TYPICAL PERFORMANCE CHARACTERISTICS Conditions: VS = 5.0 V; BST − DRN = 5.0 V; CLOAD = 5.7 nF; Room Temperature. Conditions: VS = 5.0 V; BST − DRN = 5.0 V; CLOAD = 5.7 nF; Room Temperature. Figure 16. Bottom Gate Fall Time Figure 17. Bottom Gate Rise Time +5.0 V + − TG BG PGND DRN C3 5.7 nF Measurements +5.0 V 0V EN CO BST NCP5351 VS Input Pulse 60 ns C4 5.7 nF C1 100 nF C2 100 nF Figure 18. Bottom Gate and Top Gate Rise/Fall Time Test ORDERING INFORMATION Package Shipping† SOIC−8 98 Units / Rail NCP5351DG SOIC−8 (Pb−Free) 98 Units / Rail NCP5351DR2 SOIC−8 2500 / Tape & Reel NCP5351DR2G SOIC−8 (Pb−Free) 2500 / Tape & Reel NCP5351MNR2 DFN10 2500 / Tape & Reel DFN10 (Pb−Free) 2500 / Tape & Reel Device NCP5351D NCP5351MNR2G † For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 12 NCP5351 PACKAGE DIMENSIONS DFN10, 3x3, 0.5P CASE 485C−01 ISSUE B D PIN 1 REFERENCE 2X ÇÇÇ ÇÇÇ ÇÇÇ ÇÇÇ 0.15 C 2X EDGE OF PACKAGE A B L1 E DETAIL A Bottom View (Optional) MOLD CMPD (A3) DETAIL B A1 A 10X SIDE VIEW A1 D2 1 C DETAIL A e L A3 DETAIL B Side View (Optional) SEATING PLANE 0.08 C 10X ÉÉÉ ÉÉÉ EXPOSED Cu TOP VIEW 0.15 C 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. TERMINAL b MAY HAVE MOLD COMPOUND MATERIAL ALONG SIDE EDGE. MOLD FLASHING MAY NOT EXCEED 30 MICRONS ONTO BOTTOM SURFACE OF TERMINAL b. 6. DETAILS A AND B SHOW OPTIONAL VIEWS FOR END OF TERMINAL LEAD AT EDGE OF PACKAGE. DIM A A1 A3 b D D2 E E2 e K L L1 MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.18 0.30 3.00 BSC 2.40 2.60 3.00 BSC 1.70 1.90 0.50 BSC 0.19 TYP 0.35 0.45 0.00 0.03 SOLDERING FOOTPRINT* 5 2.6016 10X E2 K 10 10X 0.10 C A B 0.05 C 6 2.1746 b 1.8508 3.3048 BOTTOM VIEW NOTE 3 10X 0.5651 10X 0.3008 0.5000 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 13 NCP5351 PACKAGE DIMENSIONS SOIC−8 NB CASE 751−07 ISSUE AJ −X− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. A 8 5 S B 0.25 (0.010) M Y M 1 4 −Y− K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 14 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP5351/D