AnaSem 安纳森 Analog Semiconductor IC MRY1518B Series 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnetic Sensor Switch (IMPORTANT: Please check the last page for Genuine Product Labeling) Website: Tel: Email: Rev. E13-01 www.anasemi.com +852-3590-8442 [email protected] AnaSem .......... Future of the analog world Rev. E13-01 Products Data Sheet AnaSem Analog Semiconductor IC 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series GENERAL DESCRIPTIONS MRY1518B series are monolithic ICs with built-in MR magnet resistive element and CMOS switch. It becomes the non-contact switch with low current consumption, high sensitivity and reliability which is combined with magnet. A horizontal magnetic field parallel to the electrode of the package can be detected by an arbitrary polarity. (N pole ⇔ S pole) HALOGEN RoHS COMPLIANCE FEATURES CMOS + MR monolithic structure Low current consumption ··············································································· 21µA (VIN=1.8V, Ta=25°C) High-sensitivity ··············································································· Typ. 1.5mT Operating temperature range ·························································· -40 ~ +85°C Operating voltage range ································································ 1.6V ~ 6.0V Detection pulse driving cycle ································································ Typ. 1.3msec with 10µsec width Magnetic direction ································································································· Both direction / CMOS inverter one output Detection magnetic field ·························································································· Horizontal direction of marked side of package (Electrode parallel both direction) Small package ································································ SOT-23 (2.9×2.8×1.1mm) APPLICATIONS Detection of opening and closing : Mobile phone, Notebook PC, Microwave oven, Washing machine, Rice cooker, Refrigerator, Electronic dictionary, Digital camera, etc. Detection of position : Air cylinder, Antitheft window, Digital door lock, etc. Detection of water level : Water purifier, Humidifier, Bidet, etc. Detection of rotation : Water meter, Gas meter, Wattmeter, Speed meter, etc. Power supply switch : Cordless phone, Electric toothbrush, etc. AnaSem 1 www.anasemi.com [email protected] .......... Future of the analog world 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series Rev. E13-01 PRODUCTS NUMBERING GUIDE MRY1518B Design version A : CMOS output Package form T : SOT-23 (2.9×2.8×1.1mm) Detection pulse cycle B : Typ. 1.3msec with 10µsec width Operating voltage 18 : 1.6V ~ 6.0V Detection sensitivity 15 : Typ. 1.5mT PIN CONFIGURATION / MARKING SPECIFICATION Pin Configuration Vss 3 A B C No. Symbol 1 VIN 2 VOUT 3 VSS Descriptions Voltage input Output D D D D D Power ground 2 1 Vin Vout Marking Specification (Top view) Code Mark Contents A M Series name BC BA Products specification & version D Internal rule Lot number AnaSem www.anasemi.com [email protected] 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series Rev. E13-01 BLOCK DIAGRAM Direction of magnetic field Switch ② VOUT NC ③ Sampling circuit R1 R2 Latch circuit R3 R4 CMOS drive circuit T1 VSS ④ ① VIN ABSOLUTE MAXIMUM RATINGS Items Symbol Min. Typ. Max. Conditions Operating temperature TOPR -40 - +85 °C Storage temperature TSTG -50 - +125 °C Supply voltage VMAX VIN-0.3 - VIN+6.0 V Assembly temp. condition TASY - 255 260 t=max:5sec/Tmax Unit °C AnaSem www.anasemi.com [email protected] 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series Rev. E13-01 ELECTRICAL CHARACTERISTICS (Unless otherwise specified, VDD=1.8V, Ta=25°C) Items Symbol Min. Typ. Max. Operating voltage VIN 1.6 1.8 6.0 V Current consumption IAVG - 21 35 µA ts - 1.3 2.5 “H”-level output voltage VOH 0.9VIN - - IOUT=+0.5mA V “L”-level output voltage VOL - - 0.1VIN IOUT=-0.5mA V Detection pulse driving cycle Conditions Unit Pulse width : 1/128 msec MAGNETIC CHARACTERISTICS (Unless otherwise specified, VDD=1.8V, Ta=25°C) Items Magnetic flux density at operating point (H→L) Magnetic flux density at release point (L→H) Width of hysteresis Symbol Min. Typ. Max. MOPS 1.0 * 1.5 2.2 MOPN -2.2 -1.5 -1.0 MRPS 0.8 1.2 1.9 MRPN -1.9 * -1.2 -0.8 MHYS 0.1 * 0.3 0.8 * Unit mT * * mT mT Note : The values with [*] marks are guaranteed by design, not tested in production. MAGNETIC-ELECTRIC CONVERSION CHARACTERISTIC VOUT VOH N-pole S-pole VOL MHYS MHYS Magnetic flux density MRPN MOPN 0 MRPS MOPS AnaSem www.anasemi.com [email protected] 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series Rev. E13-01 MAGNETIC FLUX DENSITY AND OUTPUT VOLTAGE LEVEL Conditions Magnet & Power Magnet = OFF Magnet = ON Magnet = OFF / / Power = ON Power = ON / Output level Magnet flux density Power = ON M = 0mT High-level M ≧ 2.2mT Low-level M ≦ 0.8mT High-level DETECTION PULSE DRIVING CYCLE (SAMPLING CYCLE) IDD Period (Typ. 1.3mS) (VDD=1.8V) Awake (10µS) IDD ON (Typ. 1.8mA) Sleep (Output latched) IDD AVG (Typ. 21µA) IDD OFF (Typ. 1.3µA) time OUTPUT SWITCHING TIMING CHART On Sampling pulse MHYS Off Magnetic flux MOP (Typ. 1.5mT) MRP (Typ. 1.2mT) H-level VOUT L-level Latch Latch Latch AnaSem www.anasemi.com [email protected] 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series Rev. E13-01 TEST CIRCUIT S or N VOUT Direction of magnetic field NC 15pF (including probe capacitance) VIN VSS A N or S STANDARD MAGNET SPECIFICATIONS P-point : Magnetic flux density measuring position 0.5mm Magnet maker : TDK Corp. / Japan Neodymium magnet Magnetic specification : NE047BW Size : 4.0 × 3.0 × 0.5mm 3.0mm 4.0mm Magnetization direction for reaction of sensor DETECTION DISTANCE SIMULATION (with standard magnet) Vertical direction (VD) Horizontal direction (HD) ( HD = 0mm ) ( VD = 3mm ) 20 10 9 Standard magnet Detection point of sensor 16 Magnetic flux density (mT) Magnetic flux density (mT) 18 14 12 10 8 6 4 2 0 1.5mT 2 4 6 8 10 12 14 16 18 20 Standard magnet Detection point of sensor 8 7 6 5 4 3 2 1.5mT 1 0 2 Vertical distance (mm) 4 6 8 10 12 14 16 18 20 Horizontal distance (mm) AnaSem www.anasemi.com [email protected] 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series Rev. E13-01 APPLICATION INFORMATIONS Detection of magnetic field To operate output switch, the magnetic field should be applied to the sensor with sufficient magnetic flux density and correct direction. MR series are designed to be ON-state (L-level output) when the horizontal direction magnetic field is applied in parallel to the marked side of sensor, with sufficient magnetic flux (MOPS or MOPN value) regardless of polarity of magnet. Because MR series detect the horizontal direction magnetic field, it has not influence of the reverse-magnetic field. And also, MR series detect the vertical direction magnetic field according to the level of magnetic flux, so that it is possible to apply to not only slide type but also fold type. Front view VSS Top view N or S S or N 35° Detection direction N or S S or N 35° (Marked side) VIN VOUT VIN VOUT Application example 1 -- [Fold type] VD Magnet MR sensor VD VD Position B Output level = Low → High Position A Output level = Low Position C Output level = High In case MR series is used for fold type cellular phone, IC sense the conditions of opening and shutting of the cover by detection of the magnetic flux according to the distance between IC and magnet. In position A, output is L-level (ON-state) because the detected magnetic flux is sufficient. The magnetic flux decrease according to the magnet is moved from IC (Position A→B). Then the IC is turned H-level (OFF-state) because the magnetic flux become MRP or less (Position B→C). Moving direction Moving direction S or N Magnetic field direction N or S S or N Moving direction Magnetic field direction N or S Moving direction Detection direction Detection direction AnaSem www.anasemi.com [email protected] 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series Rev. E13-01 Application example 2 -- [Slide type & Rotary type] Magnet VD MR sensor HD HD Position A Position B Position C Output level = Low Output level = Low → High Output level = High Magnet MR sensor MR sensor Position A Output level = High → Low MR sensor Position B Output level = Low MR sensor Position C Output level = Low → High Position D Output level = High In the detection of the slide type, there are two ways of arrangement of magnetic field detecting direction against moving direction. One is parallel and another is cross with moving direction. In case of parallel positioning of magnetic field with moving direction [arrangement 1], the output of IC might be L-level (ON-state) → H-level (OFF-state) → L-level (ON-state) → H-level (OFF-state) due to reverse-magnetic field. To prevent from this malfunction, it is recommended to arrange the detection direction of sensor and magnetic field to be crossed with moving direction of cover [arrangement 2]. S or N Moving direction Moving direction N or S Moving direction S or N Moving direction Magnetic field direction Magnetic field direction N or S Detection direction Detection direction [Arrangement 1] [Arrangement 2] Parallel the direction of detection magnetic field with the moving direction Cross the direction of detection magnetic field with the moving direction AnaSem www.anasemi.com [email protected] 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series Rev. E13-01 PACKAGE DIMENSIONS (SOT-23) (Unit : mm) 0.65 –0.15 +0.10 2.9±0.2 1.1~1.3 0~0.35 0.45 1.6±0.15 2.8±0.2 +0.10 0.4 –0.15 (Marked Side) 0~0.1 3~7° +0.10 +0.10 0.16 –0.15 +0.10 0.95 +0.10 0.4 –0.15 0.65 –0.15 0.4 –0.15 0.95 1.9±0.2 2.9±0.2 1.1~1.3 Recommended land pattern 1.0 2.4 0~0.1 +0.10 0.4 –0.15 0.8 1.0 0.8 1.0 0.8 0.95 0.95 1.9 AnaSem www.anasemi.com [email protected] 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series Rev. E13-01 TAPING AND LOADING SPECIFICATIONS (SOT-23) (Unit : mm) 1.65 max. Mark ø1.05±0.05 3.5±0.05 3.3±0.1 Mark 2.0±0.05 4.0±0.1 8.0±0.2 ø1.5 +0.1 –0 0.2±0.05 1.75±0.1 4.0±0.1 3.35±0.1 Taping direction REEL DIMENSIONS (SOT-23) (Unit : mm) 120° ø60±1 2.0±0.5 (3,000 pcs / reel) ø178±2 ø13±0.5 90° 9.0±0.5 AnaSem www.anasemi.com [email protected] AnaSem AnaSem may change the products described in this data sheet, or may discontinue production or services without any notice in order to supply the best products through improve the design and performance. Customers are recommended to obtain the latest data or information before placing orders in order to make sure the data or information required is the newest. It is necessary for customers to fully understand the products described in this data sheet and to use it in accordance with its specifications. The products described in this data sheet are not intended to use for the apparatus which have influence on human lives due to the failure or malfunction of the products. AnaSem Corp. is not responsible for any support to customer’s application, product design, software performance, patent infringement or service. AnaSem Corp. does not disclose or imply a guarantee or description about being licensed based on patents, copy-rights, circuit location license, or other intellectual properties associated with the devices or combinations in which the products or service of AnaSem Corp. are used or can be used, or which cover the methods. Customers should not export, directly or indirectly, any products without obtaining required licenses and approvals in advance from appropriate government agencies. AnaSem www.anasemi.com [email protected] 1.3msec High speed detection, 1.5mT High sensitivity CMOS MR Magnet Sensor Switch MRY1518B Series Rev. E13-01 GENUINE PRODUCT LEGITIMATE LABEL DEFINITION Green colored Circle “RoHS” Label Other specific customized Labels Ordinary Product Information Bar Code Our internal Outgoing Check Code 3 Our Internal QR Check Code 2 AnaSem Logo and Brand Name (Black color Logo) Our Internal Product Check Code 1 Genuine labels MUST include our correct contact information as shown AnaSem www.anasemi.com [email protected]