MACOM FBR07HA121NB-00

Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products.
Please note that TAIYO YUDEN CO., LTD. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification.
■ Please contact TAIYO YUDEN CO., LTD. for further details of product specifications as the individual specification
is available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact TAIYO YUDEN CO., LTD. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called“TAIYO YUDEN’
s official sales channel”).
It is only applicable to the products purchased from any of TAIYO YUDEN’s official sales channel.
■ Please note that TAIYO YUDEN CO., LTD. shall have no responsibility for any controversies or disputes that may
occur in connection with a third party's intellectual property rights and other related rights arising from your usage
of products in this catalog. TAIYO YUDEN CO., LTD. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to“Foreign Exchange and Foreign Trade Control Law”of Japan,“U.S. Export Administration Regulations”, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
14
LEADED FERRITE BEAD INDUCTORS(FB SERIES A TYPE / R TYPE)
LEADED FERRITE BEAD INDUCTORS (FB SERIES A TYPE / R TYPE)
■PARTS NUMBER
F
B
①
A
②
WAVE
*Operating Temp. : -25~+85℃(Including self-generated heat)
0
4
③
①Series name
Code
FB
②Shape
Code
A
R
H
A
4
④
5 0
⑤
B
B
⑥
Series name
Ferrite bead
Shape
Axial lead
Radial lead
④Material
Code
HA
VA
⑤Nominal impedance
Code
(example)
850
121
Material
Refer to impedance curves
for material differences
△=Blank space
⑥Lead configuration
Code
Lead configurations[mm]
AB
Straight lead (26mm lead space) / ammo
BB
Straight lead (52mm lead space) / ammo
KD
Formed lead (10mm pitch) / bulk
KE
Formed lead (12.5mm pitch) / bulk
KF
Formed lead / bulk (15.0mm pitch) / bulk
Lead (2.5mm pitch)/bulk (FBR)
NA
Straight lead / bulk (FBA)
NB
Formed lead (crimped) / bulk
SA
Straight lead (FBR05 type) / ammo
SB
Straight lead (FBR07 type) / ammo
TB
Straight lead (FBR07 type) / ammo
UB
Radial lead formed / ammo
US
Formed lead (crimped) / bulk
VB
Dual side lead formed (crimped) / ammo
VS
Formed lead / bulk
⑦Internal code
Code
-00
Internal code
Standard
Nominal impedance[Ω min.]
85
120
Excluding 03type
■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
/ FERRITE BEAD INDUCTORS
NOISE SUPPRESSION COMPONENTS
③Dimensions of core(D)
Code
Dimensions of core(D)[mm]
03
φ2.5
04
φ3.5
05
5.0
06
6.0
07
7.5
- 0 0
⑦
i_leaded_FBA_FBR_e-E02R01
▶This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
14
115
Unit:mm(inch)
□Please specify the lead configuration code.
Note: Lead diameter (φd) shall fall within a range of 0.65mm±0.05mm, FBR05, and FBR07 types however, will have a lead diameter (φd) range of
0.6mm±0.05mm.
/ FERRITE BEAD INDUCTORS
NOISE SUPPRESSION COMPONENTS
■PARTS NUMBER
●FBA
Parts number
FBA03△450[]-00
FBA04△450[]-00
FBA04△600[]-00
FBA04△900[]-00
EHS
Nominal impedance
[Ω](min.)
RoHS
RoHS
RoHS
RoHS
35.0
45.0
60.0
90.0
EHS
Nominal impedance
[Ω](min.)
Impedance measuring frequency
[MHz]
Material
HA
VA
50
100
50
100
50
100
50
100
Rated current
[A](max.)
Material
HA
7.0
7.0
7.0
7.0
VA
7.0
7.0
7.0
7.0
DC Resistance
[Ω](max.)
Rated current
[MΩ](min.)
0.01
0.01
0.01
0.01
1.0
1.0
1.0
1.0
DC Resistance
[Ω](max.)
Rated current
[MΩ](min.)
0.01
0.01
0.01
0.01
0.01
1.0
1.0
1.0
1.0
1.0
●FBR
Parts number
FBR05VA121[]-00
FBR06△850NA-00
FBR06△121NA-00
FBR07△850[]-00
FBR07△121[]-00
RoHS
RoHS
RoHS
RoHS
RoHS
120.0
85.0
120.0
85.0
120.0
Impedance measuring frequency
[MHz]
Material
HA
VA
100
50
100
50
100
50
100
50
100
Rated current
[A](max.)
Material
HA
7.0
7.0
7.0
7.0
VA
7.0
7.0
7.0
7.0
7.0
※△Please specify material codes (HA,VA) and [] lead configuration code.
i_leaded_FBA_FBR_e-E02R01
▶This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
116
14
LEADED FERRITE BEAD INDUCTORS
■PACKAGING
①Minimum Quantity
●Axial lead (FBA)
Type
Lead Configuration
NA, KD, US
KE, KF, VS
AB, BB
UB, VB
NA, KD, US
KE, KF, VS
AB, BB
VB, UB
FBA03
FBA04
Standard quantity [pcs]
Taped
Bulk
Ammo
1000
-
500
-
-
2000
-
3000
1000
-
500
-
-
1000
-
3000
●Radial lead (FBR)
Type
Lead Configuration
NA
SA
NA
NB
SB
FBR05
FBR06
FBR07
Standard quantity [pcs]
Taped
Bulk
Ammo
1000
-
-
2000
1000
-
1000
-
-
2000
②Bulk dimensions
Axial lead (FBA)
●NA
Type
FBA03□450
FBA04□450
FBA04□600
FBA04□900
φD
2.5±0.2
(0.098±0.008)
3.5±0.2
(0.138±0.008)
3.5±0.2
(0.138±0.008)
3.5±0.2
(0.138±0.008)
L1
4.5±0.3
(0.177±0.012)
4.5±0.3
(0.177±0.012)
6.0+0.5/-0
(0.236+0.020/-0)
9.0±0.5
(0.354±0.020)
Dimensions
L2
6.5 max.
(0.256 max.)
6.5 max.
(0.256 max.)
8.5 max.
(0.335 max.)
11.0 max.
(0.433 max.)
φd
ℓ
0.65±0.05
(0.026±0.002)
18 min.
(0.709 min.)
Unit:mm(inch)
●US
Type
FBA03□450
FBA04□450
φD
2.5±0.2
(0.098±0.008)
3.5±0.2
(0.138±0.008)
A
4.5±0.3
(0.177±0.012)
4.5±0.3
(0.177±0.012)
Dimensions
a
9.0 max.
(0.354 max.)
9.0 max.
(0.354 max.)
F
φd
5.0±1.0
(0.197±0.039)
0.65±0.05
(0.026±0.002)
Unit:mm(inch)
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-E02R01
●KD/KE/KF
Type
Lead Symbol
FBA03□450
FBA04□450
KD
FBA04□600
FBA03□450
FBA04□450
KE
FBA04□600
FBA04□900
FBA03□450
FBA04□450
KF
FBA04□600
FBA04□900
φD
2.5±0.2
(0.098±0.008)
3.5±0.2
(0.138±0.008)
3.5±0.2
(0.138±0.008)
2.5±0.2
(0.098±0.008)
3.5±0.2
(0.138±0.008)
3.5±0.2
(0.138±0.008)
3.5±0.2
(0.138±0.008)
2.5±0.2
(0.098±0.008)
3.5±0.2
(0.138±0.008)
3.5±0.2
(0.138±0.008)
3.5±0.2
(0.138±0.008)
F
10.0±1.0
(0.394±0.039)
10.0±1.0
(0.394±0.039)
10.0±1.0
(0.394±0.039)
12.5±1.0
(0.492±0.039)
12.5±1.0
(0.492±0.039)
12.5±1.0
(0.492±0.039)
12.5±1.0
(0.492±0.039)
15.0±1.0
(0.591±0.039)
15.0±1.0
(0.591±0.039)
15.0±1.0
(0.591±0.039)
15.0±1.0
(0.591±0.039)
Dimensions
L1
4.5±0.3
(0.177±0.012)
4.5±0.3
(0.177±0.012)
6.0+0.5/-0
(0.236+0.020/-0)
4.5±0.3
(0.177±0.012)
4.5±0.3
(0.177±0.012)
6.0+0.5/-0
(0.236+0.020/-0)
9.0±0.5
(0.354±0.020)
4.5±0.3
(0.177±0.012)
4.5±0.3
(0.177±0.012)
6.0+0.5/-0
(0.236+0.020/-0)
9.0±0.5
(0.354±0.020)
φd
0.65±0.05
(0.026±0.020)
0.65±0.05
(0.026±0.020)
0.65±0.05
(0.026±0.020)
ℓ
7.0±2.0
(0.276±0.079)
7.5±2.0
(0.295±0.079)
7.5±2.0
(0.295±0.079)
7.0±2.0
(0.276±0.079)
7.5±2.0
(0.295±0.079)
7.5±2.0
(0.295±0.079)
7.5±2.0
(0.295±0.079)
7.0±2.0
(0.276±0.079)
7.5±2.0
(0.295±0.079)
7.5±2.0
(0.295±0.079)
7.5±2.0
(0.295±0.079)
Unit:mm(inch)
●VS
※5±1 for 900 type only
Type
FBA03□450
FBA04□450
FBA04□600
FBA04□900
φD
2.5±0.2
(0.098±0.008)
3.5±0.2
(0.138±0.008)
3.5±0.2
(0.138±0.008)
3.5±0.2
(0.138±0.008)
A
4.5±0.3
(0.177±0.012)
4.5±0.3
(0.177±0.012)
6.0+0.5/-0
(0.236+0.020/-0)
9.0±0.5
(0.354±0.020)
Dimensions
a
12.5 max.
(0.492 max.)
12.5 max.
(0.492 max.)
12.5 max.
(0.492 max.)
16.0 max.
(0.630 max.)
F
5.0±1.0
(0.197±0.039)
5.0±1.0
(0.197±0.039)
5.0±1.0
(0.197±0.039)
5.0±1.0
(0.197±0.039)
φd
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
Unit:mm(inch)
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-E02R01
Radial lead (FBR)
●NA
Type
FBR05VA121
FBR06□850
FBR06□121
Dimensions
D
5.0 max.
(0.197 max.)
6.0±0.5
(0.236±0.020)
6.0±0.5
(0.236±0.020)
L1
9.0 max.
(0.354 max.)
7.0 max.
(0.276 max.)
9.0 max.
(0.354 max.)
φd
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
ℓ
10.0+3/-5
(0.394+0.118/-0.197)
10.0+3/-5
(0.394+0.118/-0.197)
10.0+3/-5
(0.394+0.118/-0.197)
W
2.5 max.
(0.098 max.)
3.0±0.5
(0.118±0.020)
3.0±0.5
(0.118±0.020)
F
2.5±1.0
(0.098±0.039)
2.5±1.0
(0.098±0.039)
2.5±1.0
(0.098±0.039)
Unit:mm(inch)
●NB
Type
FBR07□850
FBR07□121
D
7.5±0.5
(0.295±0.020)
7.5±0.5
(0.295±0.020)
L1
7.0 max.
(0.276 max.)
9.0 max.
(0.354 max.)
φd
0.6±0.05
(0.024±0.002)
0.6±0.05
(0.024±0.002)
Dimensions
ℓ
5.0+1/-2
(0.197+0.039/-0.079)
5.0+1/-2
(0.197+0.039/-0.079)
W
2.5 max.
(0.098 max.)
2.5 max.
(0.098 max.)
F
5.0+1/-0.5
(0.197+0.039/-0.020)
5.0+1/-0.5
(0.197+0.039/-0.020)
Unit:mm(inch)
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-E02R01
③Taping Dimensions
●AB(a: 26mm)(1.02inch lead space)
Type
FBA03
φD
2.5±0.2
(0.098±0.008)
FBA04□450
FBA04□600
3.5±0.2
(0.138±0.008)
FBA04□900
L
4.5±0.3
(0.177±0.012)
4.5±0.3
(0.177±0.012)
6.0+0.5/-0
(0.236+0.020/-0)
9.0±0.5
(0.354±0.020)
Dimensions
a
26.0+1.5/-0
(1.02+0.059/-0)
26.0+1.5/-0
(1.02+0.059/-0)
26.0+1.5/-0
(1.02+0.059/-0)
26.0+1.5/-0
(1.02+0.059/-0)
b
0.8max
(0.031max)
0.8max
(0.031max)
0.8max
(0.031max)
0.8max
(0.031max)
|L1-L2|
1.0 max
(0.039 max)
1.0 max
(0.039 max)
1.0 max
(0.039 max)
1.0 max
(0.039 max)
φd
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
Minimum insertion
pitch
10.0
(0.394)
10.0
(0.394)
10.0
(0.394)
12.5
(0.492)
Unit:mm(inch)
L
4.5±0.3
(0.177±0.012)
4.5±0.3
(0.177±0.012)
6.0+0.5/-0
(0.236+0.020/-0)
9.0±0.5
(0.354±0.020)
Dimensions
a
52.0+2/-1
(2.05+0.079/-0.039)
52.0+2/-1
(2.05+0.079/-0.039)
52.0+2/-1
(2.05+0.079/-0.039)
52.0+2/-1
(2.05+0.079/-0.039)
b
1.2 max
(0.047 max)
1.2max
(0.047max)
1.2max
(0.047 max)
1.2max
(0.047 max)
|L1-L2|
1.0 max
(0.039 max)
1.0 max
(0.039 max)
1.0 max
(0.039 max)
1.0 max
(0.039 max)
φd
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
0.65±0.05
(0.026±0.002)
Minimum insertion
pitch
10.0
(0.394)
10.0
(0.394)
10.0
(0.394)
12.5
(0.492)
Unit:mm(inch)
●BB(a: 52mm)( 2.05inches lead space)
Type
FBA03
φD
2.5±0.2
(0.098±0.008)
FBA04□450
FBA04□600
FBA04□900
3.5±0.2
(0.138±0.008)
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-E02R01
●SA(F: 2.5mm pitch)(0.098 inches)
Type
Symbol
Dimensions
9.0 max.
A
(0.354 max.)
2.5 max.
T
(0.098 max.)
5.0 max.
D
(0.197 max.)
18.0+2.0/-0
FBR05
H
(0.709+0.079/-0)
12.7±1.0
P
(0.500±0.039)
12.7±0.3 ※1
P0
(0.500±0.012)
5.1±0.7
P1
(0.201±0.028)
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
121:
Symbol
P2
F
△h
W
W0
W1
W2
Dimensions
6.35±1.3
(0.250±0.051)
2.5+1.0/-0.5
(0.098+0.039/-0.020)
0.0±2.0
(0.0±0.079)
18.0+1.0/-0.5
(0.709+0.039/-0.020)
12.5 min.
(0.492 min.)
9.0+0.75/-0.5
(0.354+0.030/-0.020)
3.0 max. ※2
(0.118 max.)
Symbol
Dimensions
12.7±0.3 ※1
(0.500±0.012)
3.85±0.8
(0.152±0.028)
6.35±1.3
(0.250±0.051)
5.0+1.0/-0.5
(0.197+0.039/-0.020)
0.0±2.0
(0.0±0.079)
18.0+1.0/-0.5
(0.709+0.039/-0.020)
12.5 min.
(0.492 min.)
Symbol
ℓ
φD0
φd
L
t
Dimensions
1.0 max.
(0.039 max.)
4.0±0.3
(0.157±0.012)
0.65±0.05
(0.026±0.002)
11.0 max.
(0.433 max.)
0.7±0.2
(0.028±0.008)
Unit: mm(inch)
●SB/TB(F: 5mm pitch)(0.197 inches)
Type
Symbol
Dimensions
9.0 max.
(0.354 max.)
850:
7.0 max.
(0.276 max.)
2.5 max.
(0.098 max.)
7.5±0.5
(0.925±0.020)
SB:
18.0+2.0/-0
(0.709+0.079/-0)
TB:
16.0±0.5
(0.630±0.020)
12.7±1.0
(0.500±0.039)
121:
A
T
FBR07
D
H
P
Symbol
P0
P1
P2
F
△h
W
W0
W1
W2
ℓ
φD0
φd
L
t
Dimensions
9.0+0.75/-0.5
(0.354+0.039/-0.020)
3.0 max. ※2
(0.118 max.)
1.0 max.
(0.039 max.)
4.0±0.3
(0.157±0.012)
0.65±0.05
(0.02±0.002)
11.0 max.
(0.433 max.)
0.7±0.2
(0.028±0.008)
Unit: mm(inch)
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-E02R01
●UB
Type
Symbol
Dimensions
4.5±0.3
A
(0.177±0.012)
9.0 max.
A1
(0.354 max.)
03:
2.7 max.
(0.106 max.)
φD
FBA03□450
04:
3.7 max.
FBA04□450
(0.146 max.)
20.0+0.5/-1.0
H
(0.787+0.020/-0.039)
12.7±1.0
P
(0.500±0.039)
12.7±0.3 ※1
P0
(0.500±0.012)
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
Symbol
P1
P2
F
△h
W
W0
W1
Dimensions
3.85±0.8
(0.152±0.032)
6.35±1.3
(0.250±0.051)
5.0±1.0
(0.197±0.039)
0.0±2.0
(0.0±0.079)
18.0+1.0/-0.5
(0.709+0.039/-0.020)
12.5 min.
(0.492 min.)
9.0+0.75/-0.5
(0.354+0.030/-0.020)
Symbol
Dimensions
12.7±0.3 ※1
(0.500±0.012)
3.85±0.8
(0.152±0.032)
6.35±1.3
(0.250±0.051)
5.0±1.0
(0.197±0.039)
0.0±2.0
(0.0±0.079)
18.0+1.0/-0.5
(0.709+0.039/-0.020)
12.5 min.
(0.492 min. )
9.0+0.75/-0.5
(0.354+0.030/-0.020)
Symbol
W2
ℓ
φD0
φd
L
t
Dimensions
3.0 max. ※2
(0.118 max.)
1.0 max.
(0.039 max.)
4.0±0.3
(0.157±0.012)
0.65±0.05
(0.026±0.002)
11.0 max.
(0.433 max.)
0.7±0.2
(0.028±0.008)
Unit: mm(inch)
●VB 形状
Type
Symbol
Dimensions
4.5±0.3
(0.177±0.012)
600:
6.0+0.5/-0
A
(0.236+0.020/-0)
900:
9.0±0.5
(0.354±0.020)
450:
12.5 max.
FBA03□450
600:
(0.492 max.)
FBA04□450
A1
FBA04□600
900:
16.0 max.
FBA04□900
(0.630 max.)
3.7 max.
φD
(0.146 max.)
16.0±0.5
H0
(0.650±0.020)
12.7±1.0
P
(0.500±0.039)
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
450:
Symbol
P0
P1
P2
F
△h
W
W0
W1
W2
ℓ
φD0
φd
L
t
Dimensions
3.0 max. ※2
(0.118 max.)
1.0 max.
(0.039 max.)
4.0±0.3
(0.157±0.012)
0.65±0.05
(0.026±0.002)
11.0 max.
(0.433 max.)
0.7±0.2
(0.028±0.008)
Unit: mm(inch)
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-E02R01
AXIAL LEADED INDUCTORS(CAL Type)、
RADIAL LEADED INDUCTORS(LH Type)、
LEADED FERRITE BEAD INDUCTORS( FB Series A Type/R Type)
■RELIABILITY DATA
1. Operating temperature Range
CAL45 Type
Specified Value
-25~+ 105℃
LHL□□□
FBA/FBR
Test Methods and
Remarks
CAL45 Type
LHL□□□
-25~+ 85℃
: Including self-generated heat
: Including self-generated heat
2. Storage temperature Range
CAL45 Type
Specified Value
LHL□□□
-40~+ 85℃
FBA/FBR
3. Rated current
CAL45 Type
Specified Value
LHL□□□
Within the specified tolerance
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
The maximum DC value having inductance within 10% and temperature increase within 40℃ by the application of DC bias.
LHL□□□ :
The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10:within 30%) and temperature increase within the
following specified temperature by the application of DC bias.
Reference temperature
: 25℃(LHL08, LHL10, LHL13)
: 30℃(LHL16, LHLP□□)
: 40℃(LHLC08, LHLC10)
FBA/FBR :
No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be
within ±20% of the initial value.
This is not guaranteed for electrical characteristics during current application.
4. Impedance
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
Test Methods and
Remarks
FBA/FBR :
Measuring equipment
Measuring frequency
Within the specified tolerance
: Impedance analyzer (HP4191A) or its equivalent
: Specified frequency
5. Inductance
CAL45 Type
Specified Value
LHL□□□
Within the specified tolerance
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Measuring equipment
Measuring frequency
LHL□□□ :
Measuring equipment
Measuring frequency
: LCR meter (HP4285A + HP42851A or its equivalent)
: Specified frequency
: LCR meter (HP4285A+HP42851A or its equivalent)
: LCR meter (HP4263A) or its equivalent (at 1kHz)
: Specified frequency
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E02R01
6. Q
CAL45 Type
Specified Value
LHL□□□
Within the specified tolerance
FBA/FBR
Test Methods and
Remarks
LHL□□□ (except LHLP) :
Measuring equipment
: LCR meter (HP4285A+HP42851A or its equivalent)
: LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency
: Specified frequency
7. DC Resistance
CAL45 Type
Specified Value
LHL□□□
Within the specified tolerance
FBA/FBR
Test Methods and
Remarks
Measuring equipment
: DC ohmmeter
8. Self resonance frequency
CAL45 Type
Specified Value
LHL□□□
Within the specified tolerance
FBA/FBR
Test Methods and
Remarks
LHL□□□(except LHLP) :
Measuring equipment
: (HP4191A, 4192A) its equivalent
9. Temperature characteristic
CAL45 Type
Specified Value
LHL□□□
△L/L : Within ±7% (except LHLP16 : Within ±20%)
FBA/FBR
Test Methods and
Remarks
Change of maximum inductance deviation in step 1 to 5
Temperature (℃)
Step
LHL□□□
1
20
2
Minimum operating temperature
3
20 (Standard temperature)
4
Maximum operating temperature
5
20
10. Tensile strength test
CAL45 Type
Specified Value
LHL□□□
No abnormality such as cut lead, or looseness.
FBA/FBR
Test Methods and
Remarks
CAL45 Type : Apply the stated tensile force progressively in the direction to draw terminal.
force (N)
duration (s)
10
10
LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal.
Nominal wire diameter tensile φd (mm)
force (N)
duration (s)
0.3<φd≦0.5
5
30±5
0.5<φd≦0.8
10
0.8<φd≦1.2
25
FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the
of the component during 10±1 seconds.
axial direction
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E02R01
11. Over current
Specified Value
CAL45 Type
No emission of smoke no firing.
LHL□□□
There shall be no scorch or short of wire.
LHLC08, LHLC10 : There shall be no firing.
FBA/FBR
Test Methods and
Remarks
LHL□□□・CAL45 Type :
Measuring current
: Rated current×2
Duration
: 5 min.
Number of measuring
: one time
12. Terminal strength : bending
CAL45 Type
Specified Value
LHL□□□
No abnormality such as cut lead, or looseness.
FBA/FBR
CAL45 Type :
Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the
initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter
Mass reference
Bending force
tensile
weight
0.3< φ d≦0.5
2.5
0.25
0.5< φ d≦0.8
5
0.50
Test Methods and
Remarks
LHL□□□・FBA/FBR :
Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the
initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter
Mass reference
Bending force
tensile
weight
0.3<φd≦0.5
2.5
0.25
0.5<φd≦0.8
5
0.5
0.8<φd≦1.2
10
1.0
13. Insulation resistance : between the terminals and body
CAL45 Type
Specified Value
LHL□□□
100MΩ min.
FBA/FBR
Test Methods and
Remarks
LHL□□□ :
Applied voltage
Duration
: 500 VDC
: 60 sec.
14. Insulation resistance : between terminals and core
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
Test Methods and
Remarks
FBA/FBR :
Applied voltage
Duration
1MΩ min.
: 100 VDC
: 60±5 sec.
15. Withstanding : between the terminals and body
CAL45 Type
Specified Value
LHL□□□
No abnormality such as insulation damage
FBA/FBR
Test Methods and
Remarks
LHL□□□ :
According to JIS C5102. 7. 1. 3 (C)
Metal global method
Applied voltage
: 500 VDC
Duration
: 60 sec.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E02R01
16. DC bias characteristic
CAL45 Type
Specified Value
△L/L : Within -10%
LHL□□□
FBA/FBR
Test Methods and
Remarks
CAL45 Type : Measure inductance with application of rated current using LCR meter to compare it with the initial value.
17. Body strength
CAL45 Type
Specified Value
No abnormality as damage.
LHL□□□
FBA/FBR
CAL45 Type :
Applied force
Duration
Speed
FBA :
Applied force
Duration
No abnormality such as cracks on body.
:50N
: 10 sec.
: Shall attain to specified force in 2 sec.
: 50±3N
: 30±1 sec.
Test Methods and
Remarks
18. Resistance to vibration
Specified Value
Test Methods and
Remarks
CAL45 Type
△L/L : Within ±5%
LHL□□□
Appearance : No abnormality
△L/L : Within ±5%
Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
Appearance : No abnormality
Impedance change : Within ±20%
CAL45 Type :
Directions
: 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range
: 10 to 55 to 10Hz (1min.)
Amplitude
: 1.5mm
Mounting method
: Soldering onto printed board.
Recovery
: At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□・FBA/FBR :
Directions
: 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range
: 10 to 55 to 10Hz (1min.)
Amplitude
: 1.5mm
Mounting method
: Soldering onto printed board.
19. Resistance to shock
CAL45 Type
Specified Value
No significant abnormality in appearance
LHL□□□
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Drop test
Impact material
Height
Total number of drops
: concrete or vinyl tile
: 1m
: 10 times
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E02R01
20. Solderability
Specified Value
Test Methods and
Remarks
CAL45 Type
At least 75% of terminal electrode is covered by new solder.
LHL□□□
At least 75% of terminal electrode is covered by new solder.
FBA/FBR
At least 90% of terminal electrode is covered by new solder.
CAL45 Type :
Solder temperature
Duration
LHL□□□ :
Solder temperature
Duration
Immersion depth
FBA/FBR :
Solder temperature
Duration
Immersion depth
: 230±5℃
: 2±0.5 sec.
: 235±5℃
: 2±0.5 sec.
: Up to 1.5mm from bottom of case.
: 230±5℃
: 3±1 sec.
: Up to 1.5mm from terminal root.
21. Resistance to soldering heat
Specified Value
CAL45 Type
△L/L : Within ±5%
LHL□□□
No significant abnormality in appearance
Inductance change : Within ±5%
Q change : Within ±30%(LHLP : only △L/L)
FBA/FBR
No significant abnormality in appearance
Impedance change : Within ±20%
CAL45 Type :
Solder temperature
Duration
Immersed conditions
Recovery
:
:
:
:
LHL□□□ :
Solder bath method :
270±5℃
5±0.5 sec. One time
Inserted into substrate with t=1.6mm
At least 1hr of recovery under the standard condition after the test, followed by the measurement within
2hrs.
Solder temperature
Duration
Manual soldering :
Caution
Recovery
:
:
:
:
:
:
:
:
260±5℃
10±1 sec.
Up to 1.5mm from the bottom of case.
350±10℃ (At the tip of soldering iron)
5±1 sec.
Up to 1.5mm from the bottom of case.
No excessive pressing shall be applied to terminals.
4 to 24hrs of recovery under the standard condition after the test.
Solder temperature
Duration
Immersion depth
Solder temperature
Duration
Immersion depth
Recovery
:
:
:
:
:
:
:
260±5℃
10±1 sec.
Up to 1.5mm from the terminal root.
350±5℃
3±1 sec.
Up to 1.5mm from the terminal root.
3hrs of recovery under the standard condition after the test.
Solder temperature
Duration
Test Methods and
Remarks
FBA/FBR :
Solder bath method:
Condition 1:
Condition 2 :
22. Resistance to solvent
CAL45 Type
Specified Value
Please avoid the ultrasonic cleaning of this product.
LHL□□□
No significant abnormality in appearance
Impedance change : Within ±20%
FBA/FBR
Test Methods and
Remarks
FBA/FBR :
Solvent temperature
Duration
Solvent type
Recovery
:
:
:
:
20~25℃
30±5 sec.
Acetone
3hrs of recovery under the standard condition after the test.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E02R01
23. Thermal shock
Specified Value
CAL45 Type
△L/L : Within ±10%
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30% (LHLP:only △L/L)
FBA/FBR
Appearance : No abnormality
Impedance change : Within ±20%
CAL45 Type:Conditions for 1cycle
Step
Temperature (℃)
1
-25+0/-3
2
Room temperature
3
+85+2/-0
4
Room temperature
Number of cycles
Recovery
Test Methods and
Remarks
Duration (min.)
30±3
Within 3
30±3
Within 3
: 5 cycles
: At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the
measurement within 2hrs.
LHL□□□・FBA/FBR: According to JIS C0025
Conditions for 1 cycle
Step
Temperature (℃)
1
Minimum operating temperature+0/-3
2
Room temperature
3
Minimum operating temperature+2/-0
4
Room temperature
Number of cycles
Recovery
:
:
:
:
Duration (min.)
30±3
Within 3
30±3
Within 3
10 cycles 〔LHL□□□〕
5 cycles (FBA/ FBR)
4 to 24hrs of recovery under the standard condition after the removal from the test chamber. 〔LHL□□□〕
3hrs of recovery under the standard condition after the removal from the test chamber. (FBA/ FBR)
24. Damp heat
CAL45 Type
Specified Value
△L/L : Within ±10%
LHL□□□
Appearance:No abnormality
Impedance change:Within ±20%
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Temperature
Humidity
Duration
Recovery
FBA/FBR :
Temperature
Humidity
Duration
Recovery
: 40±2℃
: 90~95%RH
: 1000 hrs
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
:
:
:
:
60±2℃
90~95%RH
1000 hrs
1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E02R01
25. Loading under damp heat
Specified Value
CAL45 Type
△L/L : Within ±10%
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Temperature
Humidity
Duration
Applied current
Recovery
LHL□□□ :
Temperature
Humidity
Duration
Applied current
Recovery
: 40±2℃
: 90~95%RH
: 1000 hrs
: Rated current
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
:
:
:
:
:
40±2℃
90~95%RH
1000+48/-0 hrs
Rated current
1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
26. Loading at high temperature
CAL45 Type
Specified Value
△L/L : Within ±10%
LHL□□□
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Temperature
Duration
Applied current
Recovery
: 85±2℃
: 1000 hrs
: Rated current
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
27. Low temperature life test
Specified Value
CAL45 Type
△L/L : Within ±10%
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Temperature
Duration
Recovery
LHL□□□ :
Temperature
Duration
Recovery
: -25±2℃
: 1000 hrs
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
:-40±3℃
: 1000+48/-0 hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
28. High temperature life test
CAL45 Type
Specified Value
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
Test Methods and
Remarks
LHL□□□ :
Temperature
Duration
Recovery
: 105±2℃
: 1000+48/-0 hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E02R01
AXIAL LEADED INDUCTORS(CAL Type)、
RADIAL LEADED INDUCTORS(LH Type)、
LEADED FERRITE BEAD INDUCTORS(FB Series A Type/R Type)
■PRECAUTIONS
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment,
telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical
equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear
control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or
damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
Precautions
Technical
considerations
◆Design
1. Please design insertion pitches as matching to that of leads of the component on PCBs.
◆Design
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will
cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Considerations for automatic placement
Precautions
Technical
considerations
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire inductor in the flux during the soldering operation.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering
heat, soldering etc sufficiently.
◆Recommended conditions for using a soldering iron:
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
◆Reflow soldering
1. As for reflow soldering, please contact our sales staff.
Technical
considerations
◆Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
◆Recommended conditions for using a soldering iron
If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade
the reliability of the products.
5. Cleaning
Precautions
Technical
considerations
◆Cleaning conditions
1. CAL type, LH type
Please do not do cleaning by a supersonic wave.
◆Cleaning conditions
1. CAL type, LH type,
If washing by supersonic waves, supersonic waves may deform products.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_prec_e-E02R01
6. Handling
Precautions
Technical
considerations
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
2. LH type
If inductors are dropped onto the floor or a hard surface they should not be used.
◆Packing
1. Please do not give the inductors any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading /
fragile item).
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
2. LH type
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead wire could be deformed by a fall or an excessive shock.
7. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the
storage area should be controlled.
Recommended conditions
・Ambient temperature 0~40℃
・Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may
decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
considerations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes
and deterioration of taping/packaging materials may take place.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_prec_e-E02R01