AOZ8075 6-Line EMI Filter with Integrated ESD Protection General Description Features The AOZ8075 is a 6-line device integrating EMI filtering with ESD protection for each line. It is designed to suppress unwanted EMI/RFI signals and provide electrostatic discharge (ESD) protection in portable electronic equipment. This state-of-the-art device utilizes AOS leading edge Trench Vertical Structure [TVS]2 ™ technology for superior clamping performance and filter attenuation over the full operating display range. The AOZ8075 has been optimized for protection of color LCD displays and CCD camera lines in cellular phones and other portable consumer electronic devices. z 6 lines for EMI filtering and ESD protection: The AOZ8075 consists of six identical circuits comprised of TVS diodes for ESD protection, and a resistor–capacitor network for EMI/RFI filtering. A series resistor value of 100 Ω and a capacitance value of 8 pF are used to achieve -20 dB minimum attenuation from 700 MHz to 3.0 GHz. The TVS diodes provide effective suppression of ESD voltages in excess of ±15 kV (contact discharge) and ±15 kV (air discharge). This exceeds the IEC 61000-4-2, level 4 ESD immunity test. – Exceeds IEC 61000-4-2, level 4 (ESD) immunity test – ±15 kV (contact discharge) and ±15 kV (air discharge) z Trench Vertical Structure [TVS]2 ™ based technology used to achieve excellent ESD clamping and filter performance over the full operating display range z Filter performance: -20 db attenuation from 700 MHz to 3.0 GHz z Low operating voltage: 5.0 V z Capacitance stability over wide range of voltages and temperatures z DFN package 2.50 mm x 1.20 mm z Pb-Free device Applications z EMI filtering and ESD protection for data lines z LCD displays, camera interface, I/O interface z Portable handheld devices, cell phones, PDA phones The AOZ8075 comes in an RoHS compliant, 2.50 mm x 1.20 mm DFN package and is rated over a -40 °C to +85 °C ambient temperature range. Electrical Schematic D0 100Ω CH1 8pF 8pF 100Ω D1 D5 CH2 8pF LCD/Camera Module 8pF 100Ω CH6 8pF 8pF Figure 1. Rev. 1.1 July 2011 www.aosmd.com Page 1 of 7 AOZ8075 Ordering Information Part Number Ambient Temperature Range Package Environmental AOZ8075DI -40 °C to +85 °C DFN-12 Green Product AOS Green Products use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. Pin Configuration 1 12 2 11 3 3 10 4 4 9 5 8 6 7 1 11 2 10 9 8 Exposed Pad (GND) 12 7 5 6 DFN-12 (Bottom View) Top View Pin Description Rev. 1.1 July 2011 Pin Number Pin Name Pin Function 1,12 CH 1 Channel 1 Connections 2, 11 CH 2 Channel 2 Connections 3, 10 CH 3 Channel 3 Connections 4, 9 CH 4 Channel 4 Connections 5, 8 CH 5 Channel 5 Connections 6, 7 CH 6 Channel 6 Connections Exposed Pad GND Common Ground Connection www.aosmd.com Page 2 of 7 AOZ8075 Absolute Maximum Ratings Exceeding the Absolute Maximum ratings may damage the device. Parameter Rating Storage Temperature (TS) -65 °C to +150 °C ESD Rating per IEC61000-4-2, contact ESD Rating per IEC61000-4-2, air (1) ±15 kV (1) ±15 kV ESD Rating per Human Body Model(2) ±30 kV Notes: 1. IEC 61000-4-2 discharge with CDischarge = 150 pF, RDischarge = 330 Ω. 2. Human Body Discharge per MIL-STD-883, Method 3015 CDischarge = 100 pF, RDischarge = 1.5 kΩ. Electrical Characteristics TA = 25°C unless otherwise specified. Symbol VRWM VBR IR VCL Parameter Reverse Working Voltage Conditions Typ. (3) mA(4) Reverse Breakdown Voltage IT = 1 Reverse Leakage Current VRWM = 3.3 V Signal Clamp Voltage Min. ILOAD = 1 A, positive 6 ILOAD = 5 A, positive clamp(5)(8) CCH fC Total Series Resistance 5.0 V 8 V 0.1 µA 9.0 V -2.5 clamp(5)(8) 11.5 ILOAD = 5 A, negative clamp(5)(8) -3.5 ILOAD = 12 A, positive clamp(5)(8) 14.0 ILOAD = 12 A, negative clamp(5)(8) RCH Units 7 clamp(5)(8) ILOAD = 1 A, negative Max. IR = 20 mA Ground(6)(7)(8) -5.0 90 100 110 Ω 7 8 9 pF Channel Capacitance Input to Cut-off Frequency Measured with 50 Ω source and 50 Ω load termination 220 MHz Attenuation from 700 MHz to 3.0 GHz VR = 0 V Measured with 50 Ω source and 50 Ω load termination -20 dB Notes: 3. The working peak reverse voltage, VRWM, should be equal to or greater than the DC or continuous peak operating voltage level. 4. VBR is measured at the pulse test current IT. 5. Measurements performed using a 100 ns Transmission Line Pulse (TLP) system. 6. Total capacitance is equal to 2 x CCH. 7. Measured at 25 °C, VR = 2.5 V, f = 1.0 MHz. 8. Guaranteed by design. Rev. 1.1 July 2011 www.aosmd.com Page 3 of 7 AOZ8075 Typical Performance Characteristics Insertion Loss Characteristics Analog Crosstalk 0 0 -5 -10 -20 -20 S21 (db) S21 (db) -15 -25 -30 -40 -60 -35 -40 -80 -45 -50 1 10 100 1000 -100 10000 1 10 100 Frequency (MHz) 10000 Frequency (MHz) Clamping Voltage vs. Peak Pulse Current (tperiod = 100ns, tr = 1ns) Forward Voltage vs. Forward Current (tperiod = 100ns, tr = 1ns) 6 16 Clamping Voltage, Vcl (V) 1000 5 14 4 12 3 10 2 8 1 0 6 0 2 4 6 8 10 0 12 2 4 6 8 10 12 Forward Current (A) Peak Pulse Current, Ipp (A) Typical Resistance vs. Temperature 110 Resistance (Ω) 105 100 95 90 -45 -25 -5 5 25 45 65 85 Temparature (°C) Rev. 1.1 July 2011 www.aosmd.com Page 4 of 7 AOZ8075 Package Dimensions, DFN 2.5 mm x 1.2 mm, 12L EP1 S E E1 D D1 L 12x Pin 1 Marking b Pin 1 ID (C0.2x45) e TOP VIEW BOTTOM VIEW A Dimensions in millimeters SIDE VIEW A1 A3 RECOMMENDED LAND PATTERN 1.80 0.15 0.35 Symbols A A1 b A3 D E D1 D1 e L Min. 0.50 0.00 0.15 1.15 2.45 0.25 1.75 0.20 Nom. Max. 0.55 0.60 — 0.05 0.20 0.25 0.152 REF 1.20 1.25 2.50 2.55 0.30 0.35 1.80 1.85 0.40 BSC 0.24 0.30 Dimensions in inches Symbols A A1 b A3 D E D1 D1 e L Min. 0.020 0.000 0.006 Nom. Max. 0.022 0.024 — 0.002 0.008 0.010 0.006 REF 0.045 0.047 0.049 0.096 0.098 0.100 0.010 0.012 0.014 0.069 0.071 0.073 0.016 BSC 0.008 0.010 0.012 0.20 0.30 1.0 0.40 C0.15x45 0.20 0.20 UNIT: mm Notes: 1. All dimensions are in millimeters. Converted inch dimensions are not necessarily exact. Rev. 1.1 July 2011 www.aosmd.com Page 5 of 7 AOZ8075 Tape and Reel Dimensions, DFN 2.5 mm x 1.2 mm Carrier Tape P2 P1 D0 D1 E1 K0 E2 E B0 Ref 5 T P0 A0 A–A Feeding Direction UNIT: mm Package DFN 2.5x1.2 A0 1.45 ±0.05 B0 2.80 ±0.05 K0 0.70 ±0.05 D0 D1 ø1.55 ø0.80 ±0.05 ±0.05 E 8.00 ±0.03 Reel E1 1.75 ±0.1 E2 3.50 ±0.05 P0 4.00 ±0.10 P1 4.0 ±0.10 P2 2.0 ±0.05 T 0.30 ±0.05 W1 S M K N G R H W UNIT: mm Tape Size Reel Size 8mm ø178 M ø178.0 ±1.0 N ø60.0 ±0.5 W W1 H S 11.80 ±0.5 9.0 ±0.5 ø13.0 +0.5 / –0.2 2.40 ±0.1 K 10.25 ±0.2 E ø9.8 Leader / Trailer & Orientation Trailer Tape 300mm Min. Rev. 1.1 July 2011 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm Min. Page 6 of 7 AOZ8075 Part Marking AOZ8075DI (DFN-12) 32V Part Number Code Assembly Location Code Week & Year Code This data sheet contains preliminary data; supplementary data may be published at a later date. Alpha & Omega Semiconductor reserves the right to make changes at any time without notice. LIFE SUPPORT POLICY ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. Rev. 1.1 July 2011 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.aosmd.com Page 7 of 7