IDT54/74FCT16245T/AT/CT/ET FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER IDT54/74FCT16245T/AT/CT/ET FEATURES: DESCRIPTION: • • • • • The FCT16245T 16-bit transceiver is built using advanced dual metal CMOS technology. These high-speed, low-power transceivers are ideal for synchronous communication between two busses (A and B). The Direction and Output Enable controls operate these devices as either two independent 8-bit transceivers or one 16-bit transceiver. The direction control pin (xDIR) controls the direction of data flow. The output enable pin (xOE) overrides the direction control and disables both ports. All inputs are designed with hysteresis for improved noise margin. The FCT16245T is ideally suited for driving high-capacitance loads and lowimpedance backplanes. The output buffers are designed with power off disable capability to allow "live insertion" of boards when used as backplane drivers. • • • • 0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tSK(o) (Output Skew) < 250ps Low input and output leakage ≤ 1µA (max.) ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) High drive outputs (–32mA IOH, 64mA IOL) Power off disable outputs permit “live insertion” Typical VOLP (Output Ground Bounce) < 1.0V at VCC = 5V, TA = 25°C Available in the following packages: – Industrial: SSOP, TSSOP – Military: CERPACK FUNCTIONAL BLOCK DIAGRAM 1 DIR 2 DIR 1OE 2OE 1A1 2A1 1B1 2B1 1A2 2A2 1B2 2B2 1A3 2A3 1B3 2B3 1A4 2A4 1B4 2B4 1A5 2A5 1B5 2B5 1A6 2A6 1B6 2B6 1A7 2A7 1B7 2B7 1A8 2A8 1B8 2B8 IDT and the IDT logo are registered trademark of Integrated Device Technology, Inc. MILITARY AND INDUSTRIAL TEMPERATURE RANGES JANUARY 2009 1 © 2009 Integrated Device Technology, Inc. DSC-5456/9 IDT54/74FCT16245T/AT/CT/ET FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION 1DIR 1 48 1OE Symbol Description Max Unit VTERM(2) Terminal Voltage with Respect to GND –0.5 to +7 V VTERM(3) Terminal Voltage with Respect to GND –0.5 to VCC+0.5 V TSTG Storage Temperature –65 to +150 °C IOUT DC Output Current –60 to +120 mA 1B1 2 47 1A1 1B2 3 46 1A2 GND 4 45 GND 1B3 5 44 1A3 1B4 6 43 1A4 VCC 7 42 VCC 1B5 8 41 1A5 1B6 9 40 1A6 Symbol 10 39 GND CIN Input Capacitance VIN = 0V 3.5 6 pF COUT Output Capacitance VOUT = 0V 3.5 8 pF GND 1B7 11 38 1A7 1B8 12 37 1A8 2B1 13 36 2A1 2B2 14 35 2A2 GND 15 34 GND 2B3 16 33 2A3 2B4 17 32 2A4 VCC 18 31 VCC 2B5 19 30 2A5 2B6 20 29 2A6 GND 21 28 GND 2B7 22 27 2B8 23 2DIR 24 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. All device terminals except FCT162XXXT and FCT166XXXT (APort) Output and I/O terminals. 3. Output and I/O terminals terminals for FCT162XXX and FCT166XXXT (A-Port). CAPACITANCE (TA = +25°C, F = 1.0MHz) Parameter(1) Conditions Typ. NOTE: 1. This parameter is measured at characterization but not tested. PIN DESCRIPTION Pin Names xOE Description Output Enable Inputs (Active LOW) xDIR Direction Control Inputs xAx Side A Inputs or 3-State Outputs xBx Side B Inputs or 3-State Outputs FUNCTION TABLE(1) Inputs xOE xDIR 2A7 L L Bus B Data to Bus A 26 2A8 L H Bus A Data to Bus B 25 2OE H X High Z State NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level X = Don’t Care Z = High-Impedance SSOP/ TSSOP CERPACK TOP VIEW 2 Outputs Max. Unit IDT54/74FCT16245T/AT/CT/ET FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = –40°C to +85°C, VCC = 5.0V ±10%; Military: TA = –55°C to +125°C, VCC = 5.0V ±10% Symbol Test Conditions(1) Parameter Min. Typ.(2) Max. Unit VIH Input HIGH Level Guaranteed Logic HIGH Level 2 — — V VIL Input LOW Level Guaranteed Logic LOW Level — — 0.8 V IIH Input HIGH Current (Input pins)(5) VCC = Max. — — ±1 µA — — ±1 — — ±1 — — ±1 VO = 2.7V — — ±1 VO = 0.5V — — ±1 VI = VCC Input HIGH Current (I/O pins)(5) IIL Input LOW Current (Input pins)(5) VI = GND Input LOW Current (I/O pins)(5) IOZH High Impedance Output Current IOZL (3-State Output pins)(5) VIK Clamp Diode Voltage VCC = Min., IIN = –18mA — –0.7 –1.2 V IOS Short Circuit Current VCC = Max., VO = GND(3) –80 –140 –250 mA VH Input Hysteresis — 100 — mV ICCL ICCH ICCZ Quiescent Power Supply Current — 5 500 µA VCC = Max. — VCC = Max. VIN = GND or VCC µA OUTPUT DRIVE CHARACTERISTICS Symbol IO VOH Parameter Output Drive Current Output HIGH Voltage VOL Output LOW Voltage IOFF Input/Output Power Off Leakage(5) Test Conditions(1) VCC = Max., VO = 2.5V(3) VCC = Min. IOH = –3mA, VIN = VIH or VIL IOH = –12mA MIL IOH = –15mA IND IOH = –24mA MIL IOH = –32mA IND(4) VCC = Min. IOL = 48mA MIL VIN = VIH or VIL IOL = 64mA IND VCC = 0V, VIN or VO ≤ 4.5V Min. –50 –2.5 2.4 Typ.(2) — 3.5 3.5 Max. –180 — — Unit mA V V 2 3 — V — 0.2 0.55 V — — ±1 μA NOTES: 1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, +25°C ambient. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Duration of the condition can not exceed one second. 5. The test limit for this parameter is ±5µA at TA = –55°C. 3 IDT54/74FCT16245T/AT/CT/ET FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES POWER SUPPLY CHARACTERISTICS Test Conditions(1) Min. Typ.(2) Max. Unit — 0.5 1.5 mA VIN = VCC VIN = GND — 60 100 µA/ MHz VCC = Max. Outputs Open fi = 10MHz VIN = VCC VIN = GND — 0.6 1.5 mA 50% Duty Cycle xOE = xDIR = GND One Bit Toggling VIN = 3.4V VIN = GND — 0.9 2.3 VCC = Max. Outputs Open fi = 2.5MHz 50% Duty Cycle VIN = VCC VIN = GND — 2.4 4.5(5) xOE = xDIR = GND Sixteen BitsTogging VIN = 3.4V VIN = GND — 6.4 16.5(5) Symbol Parameter ΔICC Quiescent Power Supply Current TTL Inputs HIGH VCC = Max. VIN = 3.4V(3) ICCD Dynamic Power Supply Current(4) VCC = Max. Outputs Open xOE = xDIR = GND One Input Togging 50% Duty Cycle Total Power Supply Current(6) IC NOTES: 1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, +25°C ambient. 3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND. 4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested. 6. IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ΔICC DHNT + ICCD (fCPNCP/2 + fiNi) ICC = Quiescent Current (ICCL, ICCH and ICCZ) ΔICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current caused by an Input Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) NCP = Number of Clock Inputs at fCP fi = Input Frequency Ni = Number of Inputs at fi 4 IDT54/74FCT16245T/AT/CT/ET FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES SWITCHING CHARACTERISTICS OVER OPERATING RANGE - INDUSTRIAL Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ tPZH tPZL tPHZ tPZL tSK(o) Parameter Propagation Delay A to B, B to A Output Enable Time xOE to A or B Output Disable Time xOE to A or B Output Enable Time xDIR to A or B(4) Output Disable Time xDIR to A or B(4) Output Skew(3) Condition(1) CL = 50pF RL= 500Ω 74FCT16245AT Min.(2) Max. 1.5 4.6 74FCT16245CT Min.(2) Max. 1.5 4.1 74FCT16245ET Min.(2) Max. 1.5 3.2 Unit ns 1.5 6.2 1.5 5.8 1.5 4.4 ns 1.5 5 1.5 4.8 1.5 4 ns 1.5 6.2 1.5 5.8 1.5 4.8 ns 1.5 5 1.5 4.8 1.5 4 ns — 0.5 — 0.5 — 0.5 ns SWITCHING CHARACTERISTICS OVER OPERATING RANGE - MILITARY Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ tPZH tPZL tPHZ tPZL tSK(o) Parameter Propagation Delay A to B, B to A Output Enable Time xOE to A or B Output Disable Time xOE to A or B Output Enable Time xDIR to A or B(4) Output Disable Time xDIR to A or B(4) Output Skew(3) Condition(1) CL = 50pF RL= 500Ω 54FCT16245T Min.(2) Max. 1.5 7.5 54FCT16245AT Min.(2) Max. 1.5 4.9 Unit ns 1.5 10 1.5 6.5 1.5 6.2 ns 1.5 10 1.5 6 1.5 5.2 ns 1.5 10 1.5 6.5 1.5 6.2 ns 1.5 10 1.5 6 1.5 5.2 ns — 0.5 — 0.5 — 0.5 ns NOTES: 1. See test circuit and waveforms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. Skew between any two outputs of the same package switching in the same direction. This parameter is guaranteed by design. 4. This limit is guaranteed but not tested. 5 54FCT16245CT Min.(2) Max. 1.5 4.5 IDT54/74FCT16245T/AT/CT/ET FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES SWITCH POSITION TEST CIRCUITS AND WAVEFORMS V CC 7.0V 500Ω V OUT VIN Pulse Generator D.U.T. 50pF RT Test Switch Open Drain Disable Low Enable Low Closed All Other Tests Open DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. 500Ω CL Test Circuits for All Outputs DATA INPUT tH tSU TIMING INPUT ASYNCHRONOUS CONTROL PRESET CLEAR ETC. SYNCHRONOUS CONTROL PRESET CLEAR CLOCK ENABLE ETC. tREM tSU 3V 1.5V 0V 3V 1.5V 0V LOW-HIGH-LOW PULSE tW 3V 1.5V 0V HIGH-LOW-HIGH PULSE 3V 1.5V 0V tH 1.5V 1.5V Pulse Width Set-up, Hold, and Release Times ENABLE SAME PHASE INPUT TRANSITION tPLH tPHL OUTPUT tPLH OPPOSITE PHASE INPUT TRANSITION tPHL 3V 1.5V 0V VOH 1.5V VOL DISABLE 3V 1.5V 0V CONTROL INPUT tPZL OUTPUT NORMALLY LOW 3V 1.5V 0V SWITCH CLOSED tPLZ 3.5V 1.5V tPZH OUTPUT NORMALLY HIGH Propagation Delay SWITCH OPEN 3.5V 0.3V VOL tPHZ 0.3V 1.5V 0V VOH 0V Enable and Disable Times NOTES: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. 2. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns. 6 IDT54/74FCT16245T/AT/CT/ET FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES ORDERING INFORMATION XX FCT Temp. Range XXX Family XXXX Device Type XX Package X Process Blank B Industrial MIL-STD-883, Class B PVG PAG Industrial Options Shrink Small Outline Package - Green Thin Shrink Small Outline Package - Green E Military Options CERPACK 245T 245AT 245CT 245ET 16 54 74 16-Bit Bidirectional Transceiver Double-Density, 5 Volt, Balanced Drive 55 C to +125 C 40 C to +85 C Datasheet Document History 01/08/09 Pg. 7 Updated the ordering information by removing the "IDT" notation and non RoHS part. CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 7 for Tech Support: [email protected]