Integrated Circuits Inc. aP23KWC24D USB Writer User Guide aP23KWC24D USB Writer USER GUIDE Aplus Integrated Circuits, Inc. www.aplusinc.com.tw [email protected] Page 1 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide Introduction The aP23KWC24D USB Writer is designed to support Aplus aP89K series Voice chips. It is suitable for: - aP89682K aP89341K aP89170K aP89085K ( 682 sec, 11 I/O chip) – DIP24 ( 341 sec, 11 I/O chip) – DIP24 ( 170 sec, 11 I/O chip) – DIP24 ( 085 sec, 11 I/O chip) – DIP24 This development system serves three main functions: Compiler – to create a dp2 file from user’s Voice files Writer – to program the dp2 file into the aP23xx chip Copier – connect DC 5V adaptor for 1 to 1 programming The Compiler is used to combine the edited voice files into the chip to form the desired Voice Group and to define the playback functions of each Voice Group by selecting different Options and Trigger Modes of each individual Voice Group. The Writer is used to program the voice data into the aP23xx devices that resulted from the Compiler Function. A Writer Board connected to the PC via USB port is required. The Copier is using the compiled *.dp2 which loads to writer then disconnect the USB and connect the DC 5V for 1 pcs copying. Page 2 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide Installation Hardware Installation aP23KWC24D is a USB based writer programmer. It is intended to be used in Windows XP,Win7,Win8 computer. Writer Board Connection 1) Connect USB cable from the writer board to the computer. The computer will display a new hardware is found message. The installation will begin automatically. 2) If there are too many USB devices are connected to your computer at the same time, the current supply from USB may not be sufficient to support the writer board. Fig. 1 The aP23KWC24D USB Writer Programmer Board Page 3 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide Running The Software Double click the file 23KWComplier.exe to launch the software. COMPILER : COMPILER DESCRIPTION: 1. Select your required IC body. --- aP23682-8pin , aP23341-8pin , aP23170-8pin , aP23085-8pin. --- aP23682-16pin , aP23341-16pin , aP23170-16pin , aP23085-16pin. --- aP89682K , aP23341K , aP89170K , aP89085K. Page 4 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide 2. Select your required trigger mode. --- Key mode / CPU parallel mode / MP3 mode / SPI mode / I2C mode / aP89 mode / SBT mode. 3. Select voice output mode. --- DAC or PWM. 4. Select your required voice file [xxx.wav] folder. 5. Show all your required voice files. (Only wav files acceptable). --- The [xxx.wav]: 8 bits or 16 bits mono xxx.wav. 6. Select the compression mode. --- ADPCM4 / ULAW8 / PCM8 / PCM16. 7. Loading the required *.wav files. 8. Show the memory of your usage. 9. Select if adding the silence. --- 1ms ~ 10000ms. 10. Select required debounce time. --- 65us or 16ms. 11. Select power on play. --- Power on play [sw0] group once. 12. Volume control setting. --- Volume level x16 / x8 / x4. 13. Select SBT loop. (At Key mode or SBT mode). --- Enable: The SBT pin sequential trigger & loop play. --- Disable: The SBT pin sequential trigger & play once. 14. Select SBT pin swap. (for 8pin device only). --- Select (SBT as OUT1) or (SBT as KEY3). [PS: Enable the SBT Swap, the SBT loop auto disable]. --- SBT as OUT1: busy-H/L, stop-H/L, LED flash (LED high active), ~LED flash (LED low active), prog-busyH/L, LoadBit. S3 ( pin7 ) 0 1 1 S2 ( pin6 ) 1 0 1 Group SW2 SW3 SW10 SBT = OUT1 Busy-H/L Stop-H/L LED …… --- SBT as Key3: SBT ( pin5 ) 0 0 0 1 1 1 1 S3 ( pin7 ) 0 1 1 0 0 1 1 S2 ( pin6 ) 1 0 1 0 1 0 1 Group SW1 SW2 SW3 SW4 SW5 SW6 SW7 15. Select if using pin S4 as data output pin. --- The SPI mode or I2C mode of data output for 24 pin IC body and 16 pin IC body. 16. Select if using the oscillator. --- XT (X’tal=16MHz ) / Rosc ext ( 68K ohm ) / Rosc Int. Page 5 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide 17. Select if using low voltage reset. --- Select ON if the IC voltage less than 2V will be reset. 18. Select the output function for output1, output2, output3. --- busy-H, busy-L. --- LED flash ( LED high active ) , ~LED flash ( LED low active ). --- stop-H , stop-L --- LoadBit: For the play command [094h+D9~D0]; [D9~D0] total 10 bits indicate the voice address. Same the aP89341 prefetch-071h [no gap loop play]. --- prog busy-H , prog busy-L can setup the each section of group. 19. Setting your required voice sections and function mode. 20. Show your final voice list. 21. Compiler: After setting the voices & function, push the button to create xxx.txt & xxx.dp2 files. 22. Re-download & Re-editing [xxx.dp2] to setting and function. 23. Show Check Sum. WRITER : WRITER DESCRIPTION: 1. Loading your programming file. (xxx.dp2) 2. Show setting and function after loading *.dp2 file. 3. Show your required IC body. Page 6 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide 4. Show voice sections and function mode. 5. Show the content of your selected section of voice list. 6. Select to blank check IC is blank? 7. Select to execute programming. 8. Select to verify the data of your programming. 9. Select if you need security mechanism. *** (If do this, it can’t be copied; it can’t be verified and can’t be Master IC.) 10. Execute your selected (6.) (7.) (8.) (9.). 11. Show the progress of “blank check”, “program”, “verify” and “load to flash”. 12. Load to Flash: download the program file (xxx.dp2) to [1 to 1 copier] writer. About : ABOUT DESCRIPTION: 1. Show software version. 2. Show website of Aplus Integrated Circuits Inc. 3. Detect writer firmware version. 4. Update writer firmware version. Page 7 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide Example for Compiler : 1. Select the IC body is [aP23085 - 8Pin]. 2. Select [Key Mode] to be our trigger mode. 3. Select the voice output is [PWM]. 4. Click Add-Wav to pick your required folder. 5. After confirming the folder, click the button. 6. All wav files in the folder will be listed here. Page 8 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide 7. Show all your required *.wav files. Double click .wav files you required in f, they will be showed in g. 7a. It will show the memory size you has been used. (Please note the data size you loaded can’t exceed the body’s memory). *** Please note the data size you loaded can’t exceed the body’s memory. If so, there are some ways to solve this problem: 1). Change it to a bigger memory size body. ex: aP23085-8Pin to aP23341-8Pin. 2). Compressed the wav files to decrease the memory size. ex: from PCM16 to PCM8. 3). Delete some required voice files. 8. If wav file is too big, we can choose compressing files to decrease their sizes. (UALW8 compress wav file to 8bits, PCM8 compress wav file to 8bits, ADPCM compress wav file to 4bits). *** Please note if your original voice is 16bits wav file which need to be compressed to 8 bits, We suggest you choose ULAW would be better. 9. If you want to add mute voice, click Silence button to set the silence time. 10. If need silence 20ms. Key in 20 (unit ms) then click OK button. Page 9 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide 11. Select the signal timing. (16ms or 65us). 12. Enable the power on play function, immediately play [SW0] once. 13. [Set volume] control function. Select the volume control Level x16 / x8 / x4. The volume control key by the [M1] and [M0] key. Volume Warp: Volume level increase to the max then begin from the level 1. Select disable: Pin M0: volume Level [+ 1]. ex: Level x8, 1234567888 …. Pin M1: volume Level [- 1]. ex: Level x8, 8765432111 …. Page 10 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide Select enable: Pin M0: volume Level [+ 1]. ex: Level x8, 12345678123 4…. Pin M1: volume Level [- 1]. ex: Level x8, 876543218765 …. 14. When trigger in “Key mode” or “SBT mode”, If enable the [SBT Loop]: It will one key sequential trigger and keep loop play in every group. If disable the [SBT Loop]: It will one key sequential trigger and play one time in every group. (*** Note: Trig level must select Level). 15. SBT pin swap other I/O pin function. ex : SBT pin swap to OUT1 as output use. 16. Select set Oscillator from Crystal mode(x’tal=16MHz), External Rosc mode(68K), Internal Rosc mode. ( if selecting Crystal mode, It must set at pin M0 & pin M1 ). 17. Select set Low Voltage Reset when voltage less than 2V IC will be reset. 18. Output Option: Setup the out1, out2, out3. Can select the busy-H, busy-L, stop-H, stop-L, LED flash (LED high active), ~LED flash(LED low active), Prog busy-H, Prog busy-L, LoadBit. Page 11 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide 19. Double click Panel-A for your setting the function of each Group. 20. Key in group number. 21. SW means group. ex : Select the second group and double click the wav files you required in (u) then Panel-B will show them. The mouse moves to Panel-B then enter right key for your adjusting the order of the wav files or insert or delete them. Page 12 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide 22. If the mouse move to Panel-A and enter right key, it will show there are additional function for add, multi-add, delete, play and stop. Add: add single group. Multi-Add: add multi-groups at one time (v-1). Delete: delete the group. Play: play all voices of the group. Stop: stop the voice playback. 23. Finish compiling, click compiler button. 24. Generate Check Sum number. 25. Loading finished compiled .dp2 file. Page 13 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide 26. Reloading .dp2 file if the voice file (*.wav) is not exist. 27. The mouse moves to Panel-C then enter right key for your modifying the path of the wav files. Page 14 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide Write the program file [ xxx.dp2 ] to IC : a. Click [Load] button to load the program file [xxx.dp2] file. After loading, it will show Check Sum 、b、c、d message. e. Select Blank Check to check if this IC is blank. Select Program to execute programming. Select Verify to execute verification. Select Security to execute IC security mechanism. ***(To avoid the data to be copied and it can’t be a master IC). PS: After the IC selecting Security, this IC can’t execute Verify. f. Click Run button to execute all your selected items in e column. (It’ll show (e.) progress & (b) message). Page 15 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide g. Click [Load to Flash] button to download .dp2 file to Writer. Page 16 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide When writer is able to be a 1 to 1 copier. *** (You must do g. step at first) 1. Disconnect USB. 2. Connect 5V adapter. 3. Push program key to execute programming. 4. When programming, yellow LED flash. When programming finished, green LED light. When programming failed , no LED light. Page 17 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide Example for About : a. Double click the www.aplusinc.com.tw will connect website Aplus Integrate Circuits Inc.. b. Double click the Writer Firmware Version will show writer firmware version. c. Double click the Firmware Update will load firmware file. Page 18 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide Inserting Devices into the Programmer - DIP package devices Device should be inserted align to the bottom of the 24-pin textool socket. Page 19 of 20 9/18/2015 Integrated Circuits Inc. aP23KWC24D USB Writer User Guide HISTORY 2015/03/27 aP23KWC24D User Guide. 2015/05/20 Dat file become dp2 file. 2015/07/17 AddDevice map & Check Sum 2015/09/18 AddLow voltage reset & CPU serial option. ModifyTrigger mode & Silence time & Usage memory size & Execute Run component control. Page 20 of 20 9/18/2015