G1033-201, 10G 1310 nm Fabry-Perot Laser Chip DATASHEET | SEPTEMBER 2015 Applications Digital Uncooled Applications FIBER OPTICS EMCORE’s G1033-201, 10G 1310 nm Fabry Perot (FP) laser chip is designed for uncooled digital applications. This laser chip is ideally suited for low cost highspeed data communication designs. 10 Gb/s Transmission Performance Highlights Features Advanced Digital Chip Design Wide Operating Temperature Range: -40 to +95°C Telcordia Technologies™ 468 Compliant Parameter Min Wavelength Typical Max 1310 Operating Temperature Range Optical Output Power Units nm -40 +25 +95 °C - - 30 mW RoHS Compliant Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Symbol Operating Temperature Range Top Storage Temperature Range Condition - Min Max -40 +95 Unit °C TSTG Continuous -40 +100 °C Optical Output Power Po Continuous - 30 mW Laser Reverse Voltage Vr Continuous - 1 V Continuous Operating Current Iop - 120 mA - 500 V 1 ESD Susceptibility - Continuous - 1 Based on human-body model of R = 1500 Ohm and C = 100 pF. In general, ESD precautions should be taken to avoid damage to the device | REV 2015.09 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. G1033-201, 10G 1310 nm Fabry-Perot Laser Chip FIBER OPTICS DATASHEET | SEPTEMBER 2015 Chip Electrical/Optical Performance Characteristics Parameter Symbol Condition Min Typ Max Unit Operating Temperature Top - -40 +25 +95 °C Optical Output Power Iop +25°C, Ith+30mA +95°C, Ith+30mA 7 5 9 7 - mW Threshold Current ITH +25°C +95°C - 8 17 12 22 mA Slope Efficiency η +25°C +95°C 0.20 0.12 0.31 0.25 - mW/mA R +25°C - 10 12 Ω VOP - - 1.3 1.6 V λ At Ith+20mA 1290 1310 1320 nm Δλ/ΔΤ - - 0.5 - nm/ C - Full Width, Half Max 32 40 48 deg Beam Divergence Angle, Horizontal - Full Width, Half Max 12 20 28 deg Laser Reverse Voltage Vr - 1 - - V Iop + 25°C - - 120 mA Spectral Width Δλ Ith+30mA - - 2.4 nm Modulation Bandwidth f3dB +25oC, Ith+30mA 10 - - GHz Rise/Fall Ttime tr / tf 20/80% - - 45 ps DC Resistance Operating Voltage Central Wavelength 1 Temperature Dependence of Central Wavelength Beam Divergence Angle, Vertical Continuous Operating Current 1 1 DC Outline Drawing | REV 2015.09 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. o G1033-201, 10G 1310 nm Fabry-Perot Laser Chip DATASHEET | SEPTEMBER 2015 FIBER OPTICS Ordering Information Part Number: G1033-201 Laser Safety This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser product. This device has been classified with the FDA/CDRH under accession number 0220309. All Versions of this laser are Class 1M laser product, tested according to IEC 60825-1:2007/EN 60825-1:2007 Single-mode fiber pigtail with SC/APC connectors (standard). Wavelength = 1.5 μm. Maximum power = 30 mW. Because of size constraints, laser safety labeling (including an FDA class 1M label) is not affixed to the module, but attached to the outside of the shipping carton. Product is not shipped with power supply. Caution: Use of controls, adjustments and procedures other than those specified herein may result in hazardous laser radiation exposure. | REV 2015.09 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.