OPTOWAY TRSL

Optoway
TRSL-8340G
1
***********************************************************************************************************************************************************************
TRSL-8340G
(RoHS Compliant)
3.3V / 1550 nm / 4.25 Gbps SFF LC SINGLE-MODE TRANSCEIVER
**********************************************************************************************************************************************************************
DESCRIPTION
FEATURES
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
The TRSL-8340G series single mode transceivers is small
form factor, low power, high performance module for
bi-directional serial optical data communications such as
4x/2x/1x Fibre Channel and 1000BASE-LX Gigabit
Ethernet. This module is designed for single mode fiber and
operates at a nominal wavelength of 1550 nm. The
transmitter section uses a multiple quantum well 1550 nm
DFB laser and is a class 1 laser compliant according to
International Safety Standard IEC-60825. The receiver
section uses an integrated InGaAs detector preamplifier
(IDP) mounted in an optical header and a limiting
post-amplifier IC. A LVPECL logic interface simplifies
interface to external circuitry.
Up to 4.25 Gb/s Bi-directional Data Links
Duplex LC Single Mode Transceiver
Fibre Channel FC-PI 400/200/100-SM-LC-L Compliant
IEEE 802.3z 1000BASE-LX Compliant
Small Form Factor, RJ-45 size, 2×5 pin Package
1550 nm DFB LD Transmitter
Up to 40km at 4.25Gb/s
AC/AC Coupled Signal Input / Output
LVTTL Transmitter Disable Input
LVTTL Signal Detect Output
Single +3.3 V Power Supply
RoHS Compliant
0 to 70oC Operation
Wave Solderable and Aqueous Washable
Class 1 Laser International Safety Standard IEC-60825
Compliant
LASER SAFETY
This single mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
APPLICATIONS
l Tri-rate 1.063/2.125/4.25 Gb/s Fibre Channel
l 1.25 Gb/s 1000 BASE-LX Gigabit Ethernet
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
FC-PI
Distance
(km)
Wavelength
TRSL-8340G
4 /2/1
400/200/100
40
1550 DFB
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Temperature
Soldering Temperature
Power Supply Voltage
Input Voltage
Output Current
Symbol
Tstg
Topr
--Vcc
--Iout
Recommended Operating Conditions
Parameter
Symbol
Power Supply Voltage
Vcc
Operating Temperature
Topr
Data Rate
Power Supply Current
Icc
(nm)
Min
-40
0
0
GND
0
Min
3.13
0
1
Package
Temp.
(oC)
2×5 LC
0 to 70
TX Power RX Sens.
RoHS
(dBm)
(dBm) Compliant
Max
85
70
260
4.5
Vcc
30
Units
o
C
o
C
o
C
V
V
mA
Typ
3.3
Max
3.47
70
4.25
200
4 to 0
-18
Yes
Notes
10 seconds on leads only
280
Units / Notes
V
o
C / air flow 1m/sec
Gb/s
mA
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2007 V1.0
Optoway
TRSL-8340G
2
***********************************************************************************************************************************************************************
Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3.47V)
Parameter
Optical
Optical Transmit Power
Optical Modulation Amplitude
@4.25 Gb/s
Output Center Wavelength
Output Spectrum Width
Side Mode Suppression Ratio
Optical Rise Time
Relative Intensity Noise
Electrical
Data Input Current – Low
Data Input Current – High
Differential Input Voltage
Data Input Voltage – Low
Data Input Voltage -- High
Disable Input Voltage -- Low
Disable Input Voltage -- High
Shut Off Time for TxDis
Symbol
Min
Typ
Max
Units
Notes
Po
0
---
4
dBm
1
OMA
1200
λ
∆λ
SMSR
tr / tf
RIN
1480
--30
IIL
IIH
VIH - V IL
VIL - V CC
VIH - V CC
VTDIS,L
VTDIS,H
tDIS
-350
µW
1580
1
90
-118
350
300
-2.0
-1.1
0
Vcc – 1.3
-1.58
-0.74
0.5
Vcc
1
nm
nm
dB
ps
dB/Hz
µA
µA
mV
V
V
V
V
ms
-20 dB width
20% to 80% Values
2
2
TX Output Enabled
TX Ouput Disabled
1. Output power is power coupled into a 9/125 µm single mode fiber.
2. These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs.
Receiver Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3. 47V)
Parameter
Symbol
Min
Typ
Sen1
---
---
Pin
Pa
Pd
0
---31
1.0
1260
---------
Max
Units
Notes
29
-18
---18
---
µW
dBm
dBm
dBm
dBm
dB
nm
3
4
Optical
Sensitivity @ 4.25 Gb/s
Maximum Input Power
Signal Detect -- Asserted
Signal Detect -- Deasserted
Signal detect -- Hysteresis
Wavelength of Operation
Electrical
Data Output Voltage – Low
Data Output Voltage – High
Signal Detect Output Voltage -- Low
Signal Detect Output Voltage -- High
VOL - VCC
VOH - VCC
VOL
VOH
-2.0
-1.1
2.0
1600
-1.58
-0.74
0.5
V
V
V
V
Transition: low to high
Transition: high to low
5
5
3. Measured at PRBS 27-1 at BERT 1E-12.
4. Represents sensitivity based on OMA spec, as corrected to incoming Extinction Ratio of 9 dB. For example, an OMA of 29 µW is
approximately equal to an average power of -17.3 dBm, average with an Extinction ratio of 9 dB.
5. These outputs are compatible with 10K, 10KH and 100K ECL and PECL outputs.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2007 V1.0
Optoway
TRSL-8340G
3
***********************************************************************************************************************************************************************
CONNECTION DIAGRAM
5 4 3 2 1
MS
TOP VIEW
6 7 8 9 10
PIN
1
2
3
4
5
6
7
Symbol
VEERX
V CC RX
SD
RD−
RD+
V CC TX
VEETX
8
TX_Disable
9
10
MS
TD+
TDMS
MS
Notes
Directly connect this pin to the receiver ground plane
+3.3V dc power for the receiver section
Active high on this indicates a received optical signal.
Receiver Dataout Bar. See recommended circuit schematic
Receiver Dataout. See recommended circuit schematic
+3.3V dc power for the transmitter section
Directly connect this plan to the transmitter ground plane
Transmitter Disable. Connect this pin to +3.3V TTL logic “1” to disable module
To enable module connect to TTL logic low “0”
Transmitter Data In. See recommended circuit schematic
Transmitter Data In Bar. See recommended circuit schematic
Mounting Studs. Connect to Chassis Ground
RECOMMENDED CIRCUIT SCHEMATIC
Vee TX 7
TX_Disabl e 8
TX_Disabl e
TD+ 9
LD
Driver
TD+
Z=50Ω
100Ω
TD- 10
VccTX
TD1μH Z=50Ω
6
VCC 3.3V
10nF
10μF
10nF
10μF
1μH
VccRX
SerDes
IC
2
10nF
10μF
RD- 4
Protocol
IC
RDZ=50Ω
100Ω
POST
Amp
RD+ 5
RDZ=50Ω
Depe ndi ng on SerDes
SD 3
Signal Dete ct
4.7K to 10KΩ
Vee RX 1
SFF Module
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2007 V1.0
Optoway
TRSL-8340G
4
***********************************************************************************************************************************************************************
PACKAGE DIAGRAM (Units in mm)
A) Standard Case
TRSL-8340G
B) Extended Case
TRSL-8340EG
Note: Specifications subject to change without notice.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2007 V1.0