Optoway XPS-2380MWG 1 *********************************************************************************************************************************************************************** XPS-2380MWG / XPS-2380BMWG / XPS-2380AMWG (RoHS Compliant) 80km / 1550 nm / 10G Multirate XFP Single-Mode Optical Transceiver ********************************************************************************************************************************************************************** FEATURES DESCRIPTION l l l l l XPS-2380MWG series transceiver is designed for single-mode fibre serial optical data communications such as SONET OC-192 / SDH STM-64, 10G Ethernet 10GBASE-ER/EW and 10G Fibre Channel. The transceiver consists of two sections: The transmitter section consists of a temperature-stabilized 1550 nm electrical-modulated laser (EML), driver and signal conditioner. The receiver section incorporates a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and signal conditioner. The module is with the XFP 30-pin connector to allow hot plug capability. Integrated Tx and Rx signal conditioners provide high jitter-tolerance for full XFI compliance and no external reference clock required. The internally ac coupled high speed serial I/O simplifies interfacing to external circuitry. +5V and +3.3V power supplies are needed. The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver. A serial EEPROM in the transceiver allows the user to access transceiver digital diagnostic monitoring and configuration data via the 2-wire XFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic data is held in the lower area while specific data is held in a series of tables in the high memory area. l l l l l l l l Support 9.95 Gbps to 11.1 Gbps Complaint with XFP MSA Compliant with XFI 10G Serial Electrical Interface Maximum Link Length of 80 km Temperature-stabilized 1550 nm 1600ps/nm EML Transmitter 2-Wire Interface for Integrated Digital Diagnostic Monitoring No reference Clock required Power Dissipation < 3.5 W +3.3V and + 5V Power Supply RoHS-6 Compliant -5 to 70oC Operating: XPS-2380MWG -5 to 85oC Operating: XPS-2380BMWG -40 to 85oC Operating: XPS-2380AMWG APPLICATIONS l SONET OC-192 / SDH STM-64 ITU-T G.959.1 P1L1-2D2 l SONET OC-192 / SDH STM-64 with ITU-T G.709 l 10GBASE-ZR / ZW 80 km 10G Ethernet l Extended 80 km 10G Fibre Channel l 80 km 10G Ethernet with ITU-T G.709 FEC LASER SAFETY This single-mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. ORDER INFORMATION P/No. XPS-2380MWG XPS-2380BMWG XPS-2380AMWG Bit Rate (Gb/s) 10G 9.95 – 11.1 9.95 – 11.1 9.95 – 11.1 Multirate* Multirate* Multirate* Distance (km) 80 80 80 Wavelength (nm) 1550 EML 1550 EML 1550 EML Package XFP with DMI XFP with DMI XFP with DMI Case Temp (oC) -5 to 70 -5 to 85 -40 to 85 RoHS Compliant Yes Yes Yes *: multirate for SONET OC-192 IR2, OC-192 IR-3, 10GBASE-ER/EW, 10G Fibre Channel, ITU-T G.709, 10GBASE-ER/EW + FEC ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 7/1/2009 V2.0 Optoway XPS-2380MWG 2 *********************************************************************************************************************************************************************** Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature Symbol Tstg Topr Relative Humidity Power Supply Voltage (5V) Power Supply Voltage (3.3V) Receiver Input Optical Power RH Vcc5 VCC3 Mip Min -40 -5 -5 -40 0 -0.5 -0.5 Max 85 70 85 85 85 6.0 3.6 -4 Units o C o C Notes XPS-2380MWG XPS-2380BMWG XPS-2380AMWG Non condensing % V V dBm Received average power Recommended Operating Conditions Parameter Power Supply Voltage (5V) Power Supply Voltage (3.3V) Power Supply Current (@5V) Power Supply Current (@3.3V) Power Dissipation Operating Case Temperature Symbol VCC5 VCC3 ICC5 ICC3 PD Topr Min 4.75 3.13 Typ 5 3.3 Max 5.25 3.47 500 750 3.5 70 85 85 11.1 -5 -5 -40 Data Rate 9.95 1. Including in rush current. Maximum module current ramp rate is 100 mA/µs. Units / Notes V V mA / 1 mA / 1 W o C / XPS-2380MWG o C / XPS-2380BMWG o C / XPS-2380AMWG Gb/s Transmitter Optical Specifications (Topr= -5 to 70oC, Vcc5=5V±5%, Vcc3 = 3.3V ±5%) Parameter Average Launch Power Extinction Ratio Output Center Wavelength Output Spectrum Width Side Mode Suppression Ratio Relative Intensity Noise Optical Eye Mask Average Launch Power of OFF Transmitter Symbol Min Typ Max Units Po, Avg 0 +4 dBm ER 8.2 dB λc 1530 1565 nm 1 nm σλ SMSR 30 dB RIN -130 dB/Hz Compliant with IEEE 802.3ae 10GBASE-L XFP MSA -30 dBm Notes 2 3 -20 dB width 2. Output power is power coupled into a 9/125 µm single-mode fiber. 3. ER=9 dB minimum for data rate 9.9 Gb/s to 10.7 Gb/s. Receiver Optical Specifications (Topr= -5 to 70oC, Vcc5=5V±5%,Vcc3 = 3.3V ±5%) Parameter Sensitivity @10.3 Gb/s [email protected] Gb/s [email protected] Gb/s Receiver Overload LOS -- Deasserted LOS -- Asserted LOS -- Hysteresis Wavelength of Operation Optical Return Loss Symbol Sen1 Sen2 Sen2 PMAX LOSD LOSA λc ORL Min -7 ---37 0.5 1270 Typ Max -23 -23 -22 ------------- -30 --1580 -27 Units dBm dBm dBm dBm dBm dBm dB nm dB Notes 4,5 4 4 Transition: low to high Transition: high to low 4. Measured at 1528 – 1600 nm with worst ER; BER<10-12 and PRBS 231-1. 5. Measured with worst ER; BER < 10-12 and PRBS 231-1. ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 9/1/2009 V2.0 Optoway XPS-2380MWG 3 *********************************************************************************************************************************************************************** Electrical Characteristics Parameter Symbol High-Speed Signal (CML) Interface Specification Input Data Rate Differential Input Impedance Rin Differential Data Input Amplitude Output Data Rate Differential Output Impedance Rout Differential Data Output Amplitude Low-Speed Signal (LVTTL) Interface Specification Input High Voltage Input Low Voltage Output High Voltage Output Low Voltage Reference Clock (LVPECL) Interface Specification Min Typ 9.95 Max Units 11.1 340 850 Gb/s Ω mVpp Gb/s Ω mVpp 2.0 GND 2.4 GND Vcc 0.8 Vcc 0.5 V V V V 100 120 9.95 820 11.1 100 Notes 1, Internally AC coupled 1, Internally AC coupled No reference clock 1. The differential input and output amplitudes are per XFP MSA mask at points B’ and C’. Transceiver Timing Characteristics Parameter TX_DIS Assert Time TX_DIS Negate Time Time to Initialize Interrupt Assert Delay Interrupt Negate Delay P_Down/PST Assert Delay P_Down Nagate Delay Mod_NR Assert Delay Mod_NR Negate Delay Mod_Desel Assert Time Mod_Desel De-Assert Time P_Down Reset Time RX_LOS Assert Delay RX_LOS Negate Delay Serial ID Clock Rate Symbol t_off t_on t_init interrupt_on interrupt_off P_Down/RST_on P_Down/RST_off Mod_nr_on Mod_nr_off T_Mod_Desel T_Mod_Sel T_reset T_Los_on T_Los_off fSCL Min Typ Max 10 2 300 200 500 100 300 1 1 2 2 10 0 100 100 400 Units µs ms ms ms µs µs ms ms ms ms ms µs µs µs kHz Notes ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 9/1/2009 V2.0 Optoway XPS-2380MWG 4 *********************************************************************************************************************************************************************** MANAGEMENT INTERFACE The structure of the memory map is shown in Figure 1, which is accessible over a 2-wire serial interface at the 8-bit address 1010000X (A0h). The normal 256 byte I2C address space is divided into low and upper blocks of 128 Bytes. The lower block of 128 Bytes is always directly available and is used for the diagnostics and control function. Multiple blocks of memories are available in the upper 128 Bytes of the address space. These are individually addressed through a table select Byte which the user enters into a location in the lower address space. Thus, there is a total available address space of 128*256 = 32 Kbytes in this upper memory space. The contents of Table 01h are listed in Table 1 below. Please refer SFF INF-8077i (Revision 4.5) for detailed information. Figure 1. 2-wire Serial Digital Diagnostic Memory Map Data Address 96 ~ 97 98 ~ 99 100 ~ 101 102 ~ 103 104 ~ 105 106 ~ 107 Table 1 Monitoring Specification Parameter Accuracy ± 3oC Temperature Reserved ± 10% ± 2dB ± 2dB ± 3% Tx Bias Tx Power Rx Power Vcc3 ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 9/1/2009 V2.0 Optoway XPS-2380MWG 5 *********************************************************************************************************************************************************************** CONNECTION DIAGRAM Table 3 PIN Description PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Logic LVTTL-I LVTTL-O LVTTL-I LVTTL-I/O LVTTL-I/O LVTTL-O LVTTL-O LVTTL-O CML-O CML-O Signal Name GND VEE5 Mod_Desel Interrupt TX_DIS VCC5 GND VCC3 VCC3 SCL SDA Mod_Abs Mod_NR RX_LOS GND GND RDRD+ GND VCC2 Description Note Module Ground -5.2V Power Supply (Not required) Module De-select; When held low allows module to respond to 2-wire serial interface Interrupt; Indicates presence of an important condition which can be read over the 2wire serial interface Transmitter Disable; Turns off transmitter laser output +5V Power Supply Module Ground +3.3V Power Supply +3.3V Power Supply Serial 2-wire interface clock Serial 2-wire interface data line Indicates Module is not present. Grounded in the Module Module Not Ready; Indicating Module Operational Fault Receiver Loss Of Signal Indicator Module Ground Module Ground Receiver Inverted Data Output Receiver Non-Inverted Data Output Module Ground +1.8V Power Supply (Not required) 1 3 2 3 1 2 2 2 2 2 1 1 1 3 ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 9/1/2009 V2.0 Optoway XPS-2380MWG 6 *********************************************************************************************************************************************************************** 21 LVTTL-I P_Down/RST 22 23 24 PECL-I VCC2 GND RefCLK+ 25 PECL-I RefCLK- 26 27 28 CML-I 29 CML-I 30 GND GND TDTD+ GND Power down; When high, requires the module to limit power consumption to 1.5W or below. 2-Wire serial interface must be functional in the low power mode. Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. +1.8V Power Supply (Not required) Module Ground Reference Clock Non-Inverted Input, AC coupled on the host board. (Not used. Internally terminated to 50 ohm (100 ohm diff.)) Reference Clock Inverted Input, AC coupled on the host board. (Not used. Internally terminated to 50 ohm (100 ohm diff.)) Module Ground Module Ground Transmitter Inverted Data Input Transmitter Non-Inverted Data Input Module Ground 3 1 4 4 1 1 1 1. Module ground pins GND are isolated from the module case and chassis ground within the module. 2. Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board. 3. These PINs are open within module. 4. A Reference Clock input is not required. If present, it will be ignored. MECHANICAL SPECIFICATION (UNITS IN MM) ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 9/1/2009 V2.0 Optoway XPS-2380MWG 7 *********************************************************************************************************************************************************************** RECOMMENDED POWER CIRCUIT SCHEMATIC Host Board VCC5 Optional Host +5V 4.7μH 0.1μF VCC3 Host +3.3V 4.7μH 22μF 0.1μF 0.1μF VCC2 Optional Host +1.8V 4.7μH 22μF 0.1μF XFP Connector 22μF 0.1μF XFP Module 0.1μF VEE5 Optional Host -5.2V 4.7μH 0.1μF 22μF 0.1μF RECOMMENDED INTERFACE CIRCUIT XFP module Host Board SerDat Out+ TD + Z=50Ω CML 100Ω CML TD - SerDat OutZ=50Ω SerDat In+ CML RD + Z=50Ω 100Ω CML SerDat In- RD Z=50Ω Vcc(+3.3V) REFCLKP 100Ω 4.7K to 10KΩ REFCLKN RX_LOS INTERRUPT SDA VCC(+3.3V) SCL MOD_NR 10KΩ MOD_abs TX_DIS GND MOD_DeSel P_Down/RST ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 9/1/2009 V2.0 Optoway XPS-2380MWG 8 *********************************************************************************************************************************************************************** Table 2 Serial ID Memory Contents (Table 01h) Address Field Size (Byte) 128 1 Identifier 129 130 1 1 Ext. Identifier Connector type 131~138 139 140 141 142 143 144 145 146 147 8 1 1 1 1 1 1 1 1 1 Transceiver Encoding BR-Min BR-Max length (SMF)-Km Length (E-50µm) Length (50 µm) Length (62.5 µm) Length (Copper) Device Tech 148~163 164 165~167 16 1 3 Vendor name CDR Support Vendor OUI OPTOWAY CDR supports 9.953G ~ 11.1G, XFI Loopback 168~183 184~185 186~187 16 2 2 XPS-2380MWG ASCII (“31 61” means 1a revision) 1550 nm 188~189 190 191 2 1 1 Vendor PN Vendor rev Wavelength Wavelength Tolerance Max Case Temp CC_BASE 192~195 4 Power Supply 196~211 16 Vendor SN 212~219 8 220 1 Date code Diagnostic Monitoring Type 221 222 223 224~255 1 1 1 32 Enhanced Options Aux Monitoring CC_EXT Vendor Specific Name of Filed Description XFP power consumption < 3.5W, no Ref Colck required LC connector 10GBASE-ZR/ZW, 10GFC Extended Reach 1550nm, SONET Long Haul G.959.1 P1L1-2D2 64B/66B, SONET Scrembled, NRZ 9.9Gbps 11.1Gbps 80 Km 0m 0m 0m 0m 1550 EML, APD detector +/- 20 nm 70deg Check sum of Byte 128 -- 190 3.5 Wmax, 1.5W pd_max , 750mA 3.3V, 500 mA 5V ASCII ASCII Year (2 Byte), Month (2 Byte), Day (2 Byte) No BER Support, Average Power Optional Soft TX_DISABLE implemented, Optional Soft P_down implemented AUX1 for Vcc3. Check sum of Byte 192 -- 222 Hex 06 90 07 00 20 00 00 00 00 04 00 F0 63 6F 50 00 00 00 00 76 4F 50 54 4F 57 41 59 20 20 20 20 20 20 20 20 20 F9 00 0E FA 58 50 53 2D 32 33 38 30 4D 57 47 20 20 20 20 20 xx xx 79 18 0F A0 46 AF 96 A8 00 xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx 20 20 08 60 70 Reserved Note: Specifications subject to change without notice. ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 9/1/2009 V2.0 Optoway XPS-2380MWG 9 *********************************************************************************************************************************************************************** REVISION HISTORY Version 1.0 2.0 Subject Release Date Initial datasheet Add a) XPS-2380BMWG for -5 to 85oC operating b) XPS-2380AMWG for -40 to 85oC operating 2008/8/1 2009/7/1 ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 9/1/2009 V2.0