OPTOWAY XPS-2310W

Optoway
XPS-2310W-CXX0G
1
***********************************************************************************************************************************************************************
XPS-2310W-CXX0G
(RoHS Compliant)
10Gbps / CWDM XFP Single-Mode Optical Transceiver for 10GbE / 10GFC
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
z
z
z
z
z
z
z
z
XPS-2310W-CXX0G series transceiver is designed for
single-mode fibre serial optical data communications such as
10G Ethernet 10GBASE-LR/LW and 10G Fibre Channel
1200-SM-LL-L.
This module is designed for single mode fiber and
operates at a nominal wavelength of CWDM wavelength.
There are eighteen center wavelengths available from 1270
nm to 1610 nm, with each step 20 nm. A guaranteed
minimum optical link budget of 11 dB is offered. The
transceiver consists of two sections: The transmitter section
consists of a directly modulated uncooled CWDM DFB laser,
driver and signal conditioner. The receiver section
incorporates a PIN photodiode integrated with a
trans-impedance preamplifier (TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Only single 3.3V power supply is needed. The
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
provided to indicate the loss of an input optical signal of
receiver.
A serial EEPROM in the transceiver allows the user to
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
Interface. This interface uses a single address, A0h, with a
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
z
z
z
z
z
z
z
Support 9.95 Gbps to 10.5 Gbps
Complaint with XFP MSA
Compliant to IEEE 802.3ae 10GBASE-LR/LW
Compliant to 10GFC 1200-SM-LL-L
Compliant with XFI 10G Serial Electrical Interface
Maximum Link Length of 10 km
Uncooled 18-Wavelength CWDM DFB LD
2-Wire Interface for Integrated Digital Diagnostic
Monitoring
XFI Loopback Mode
No reference Clock required
Only Required +3.3 V Power Supply
Power Consumption < 2 W
RoHS Compliant
-5 to 70oC Case Operating Temperature
Duplex LC Connector
APPLICATIONS
z 10GBASE-LR at 10.3125 Gb/s
z 10GBASE-LW at 9.953 Gb/s
z 10GFC at 10.51875 Gb/s
LASER SAFETY
This single-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
10GBASE
XPS-2310W-CXX0G
9.95 – 10.52
LR/LW
Power
Budget
(dB)
> 11
Wavelength
(nm)
Package
Case Temp
(oC)
RoHS
Compliant
CWDM*
XFP with DMI
-5 to 70
Yes
Max.
(nm)
1457.5
1477.5
1497.5
1517.5
1537.5
1557.5
1577.5
1597.5
1617.5
Label
CWDM* Wavelength (0 to 70oC)
Central
Wavelength
-C270
-C290
-C310
-C330
-C350
-C370
-C390
-C410
-C430
Min.
(nm)
1264.5
1284.5
1304.5
1324.5
1344.5
1364.5
1384.5
1404.5
1424.5
Typ.
(nm)
1270
1290
1310
1330
1350
1370
1390
1410
1430
Max.
(nm)
1277.5
1297.5
1317.5
1337.5
1357.5
1377.5
1397.5
1417.5
1437.5
Label
C27
C29
C31
C33
C35
C37
C39
C41
C43
Central
Wavelength
-C450
-C470
-C490
-C510
-C530
-C550
-C570
-C590
-C610
Min.
(nm)
1444.5
1464.5
1484.5
1504.5
1524.5
1544.5
1564.5
1584.5
1604.5
Typ.
(nm)
1450
1470
1490
1510
1530
1550
1570
1590
1610
C45
C47
C49
C51
C53
C55
C57
C59
C61
CWDM*: 18 Wavelengths from 1270 nm to 1610 nm, each step 20 nm.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2008
V1.0
Optoway
XPS-2310W-CXX0G
2
***********************************************************************************************************************************************************************
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Case Temperature
Relative Humidity
Power Supply Voltage
Symbol
Tstg
Topr
RH
VCC3
Min
-40
-5
0
0
Max
85
70
85
3.6
Units
o
C
o
C
%
V
Min
3.13
Typ
3.3
Max
3.47
550
2
70
10.52
Notes
Non condensing
Recommended Operating Conditions
Parameter
Power Supply Voltage
Power Supply Current (@3.3V)
Power Dissipation
Operating Case Temperature
Data Rate
Symbol
VCC3
ICC3
PD
Topr
-5
9.95
Units / Notes
V
mA
W
o
C
Gb/s
Transmitter Optical Specifications (Topr= -5 to 70oC, Vcc3 = 3.3V ±5%)
Parameter
Average Launch Power
Optical Modulation Amplitude
Extinction Ratio
Output Center Wavelength
Output Spectrum Width
Side Mode Suppression Ratio
Relative Intensity Noise
Optical Eye Mask
Average Launch Power of OFF
Transmitter
Symbol
Min
Typ
Max
Units
Po, Avg
-3
1
dBm
Po, OMA
-5.0
dBm
ER
3.5
dB
λc –5.5
λc
λc +7.5
λc
nm
1
nm
σλ
SMSR
30
dB
RIN
-128
dB/Hz
Compliant with IEEE 802.3ae 10GBASE-L XFP MSA
-30
dBm
Notes
1
2
-20 dB width
1. Output power is power coupled into a 9/125 μm single-mode fiber.
2. ITU-T G.694.2 CWDM wavelength from 1270 nm to 1610 nm, each step 20 nm.
Receiver Optical Specifications (Topr= -5 to 70oC, Vcc3 = 3.3V ±5%)
Parameter
Sensitivity
Receiver Overload
LOS -- Deasserted
LOS -- Asserted
LOS -- Hysteresis
Wavelength of Operation
Optical Return Loss
Symbol
Sen1
PMAX
LOSD
LOSA
λc
ORL
Min
Typ
0.5
---26
1
1260
---------
Max
-14
-15
--5
1620
-12
Units
dBm
dBm
dBm
dBm
dB
nm
dB
Notes
3
Transition: low to high
Transition: high to low
3. Average received power; BER < 10-12 and PRBS 231-1.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2008
V1.0
Optoway
XPS-2310W-CXX0G
3
***********************************************************************************************************************************************************************
Electrical Characteristics
Parameter
Symbol
High-Speed Signal (CML) Interface Specification
Input Data Rate
Differential Input Impedance
Rin
Differential Data Input Amplitude
Output Data Rate
Differential Output Impedance
Rout
Differential Data Output
Amplitude
Low-Speed Signal (LVTTL) Interface Specification
Input High Voltage
Input Low Voltage
Output High Voltage
Output Low Voltage
Reference Clock (LVPECL) Interface Specification
Min
Typ
Max
Units
9.95
10.3125
100
10.52
Gb/s
Ω
820
10.52
mVpp
Gb/s
Ω
1, Internally AC coupled
340
850
mVpp
1, Internally AC coupled
2.0
GND
2.4
GND
Vcc
0.8
Vcc
0.5
V
V
V
V
120
9.95
10.3125
100
Notes
No reference clock
1. The differential input and output amplitudes are per XFP MSA mask at points B’ and C’.
Transceiver Timing Characteristics
Parameter
TX_DIS Assert Time
TX_DIS Negate Time
Time to Initialize
Interrupt Assert Delay
Interrupt Negate Delay
P_Down/PST Assert Delay
P_Down Nagate Delay
Mod_NR Assert Delay
Mod_NR Negate Delay
Mod_Desel Assert Time
Mod_Desel De-Assert Time
P_Down Reset Time
RX_LOS Assert Delay
RX_LOS Negate Delay
Serial ID Clock Rate
Symbol
t_off
t_on
t_init
interrupt_on
interrupt_off
P_Down/RST_on
P_Down/RST_off
Mod_nr_on
Mod_nr_off
T_Mod_Desel
T_Mod_Sel
T_reset
T_Los_on
T_Los_off
fSCL
Min
Typ
Max
10
2
300
200
500
100
300
1
1
2
2
10
0
100
100
400
Units
μs
ms
ms
ms
μs
μs
ms
ms
ms
ms
ms
μs
μs
μs
kHz
Notes
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2008
V1.0
Optoway
XPS-2310W-CXX0G
4
***********************************************************************************************************************************************************************
Management Interface
The structure of the memory map is shown in Figure 1, which is accessible over a 2-wire serial interface at the 8-bit
address 1010000X (A0h). The normal 256 byte I2C address space is divided into low and upper blocks of 128 Bytes. The
lower block of 128 Bytes is always directly available and is used for the diagnostics and control function. Multiple blocks of
memories are available in the upper 128 Bytes of the address space. These are individually addressed through a table select
Byte which the user enters into a location in the lower address space. Thus, there is a total available address space of 128*256
= 32 Kbytes in this upper memory space. The contents of Table 01h are listed in Table 1 below. Please refer SFF INF-8077i
(Revision 4.5) for detailed information.
Figure 1. 2-wire Serial Digital Diagnostic Memory Map
Data Address
96 ~ 97
98 ~ 99
100 ~ 101
102 ~ 103
104 ~ 105
106 ~ 107
Table 1 Monitoring Specification
Parameter
Accuracy
± 3oC
Temperature
Reserved
Tx Bias
Tx Power
Rx Power
Vcc3
± 10%
± 2dB
± 2dB
± 3%
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2008
V1.0
Optoway
5
XPS-2310W-CXX0G
***********************************************************************************************************************************************************************
CONNECTION DIAGRAM
Table 3 PIN Description
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Logic
LVTTL-I
LVTTL-O
LVTTL-I
LVTTL-I/O
LVTTL-I/O
LVTTL-O
LVTTL-O
LVTTL-O
CML-O
CML-O
Signal Name
GND
VEE5
Mod_Desel
Interrupt
TX_DIS
VCC5
GND
VCC3
VCC3
SCL
SDA
Mod_Abs
Mod_NR
RX_LOS
GND
GND
RDRD+
GND
VCC2
Description
Note
Module Ground
-5.2V Power Supply (Not required)
Module De-select; When held low allows module to respond to 2-wire serial interface
Interrupt; Indicates presence of an important condition which can be read over the
2wire serial interface
Transmitter Disable; Turns off transmitter laser output
+5V Power Supply (Not required)
Module Ground
+3.3V Power Supply
+3.3V Power Supply
Serial 2-wire interface clock
Serial 2-wire interface data line
Indicates Module is not present. Grounded in the Module
Module Not Ready; Indicating Module Operational Fault
Receiver Loss Of Signal Indicator
Module Ground
Module Ground
Receiver Inverted Data Output
Receiver Non-Inverted Data Output
Module Ground
+1.8V Power Supply (Not required)
1
3
2
3
1
2
2
2
2
2
1
1
1
3
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2008
V1.0
Optoway
6
XPS-2310W-CXX0G
***********************************************************************************************************************************************************************
21 LVTTL-I
P_Down/RST
22
23
24 PECL-I
VCC2
GND
RefCLK+
25 PECL-I
RefCLK-
26
27
28 CML-I
29 CML-I
30
GND
GND
TDTD+
GND
Power down; When high, requires the module to limit power consumption to 1.5W or
below. 2-Wire serial interface must be functional in the low power mode.
Reset; The falling edge initiates a complete reset of the module including the 2-wire
serial interface, equivalent to a power cycle.
+1.8V Power Supply (Not required)
Module Ground
Reference Clock Non-Inverted Input, AC coupled on the host board. (Not used.
Internally terminated to 50 ohm (100 ohm diff.))
Reference Clock Inverted Input, AC coupled on the host board. (Not used. Internally
terminated to 50 ohm (100 ohm diff.))
Module Ground
Module Ground
Transmitter Inverted Data Input
Transmitter Non-Inverted Data Input
Module Ground
3
1
4
4
1
1
1
1. Module ground pins GND are isolated from the module case and chassis ground within the module.
2. Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board.
3. These PINs are open within module.
4. A Reference Clock input is not required. If present, it will be ignored.
Mechanical Specification (Units in mm)
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2008
V1.0
Optoway
XPS-2310W-CXX0G
7
***********************************************************************************************************************************************************************
Recommended Power Circuit Schematic
Host Board
VCC5
Optional
Host +5V
4.7μH
0.1μF
VCC3
Host +3.3V
4.7μH
22μF
0.1μF
0.1μF
VCC2
Optional
Host +1.8V
4.7μH
22μF
0.1μF
XFP Connector
22μF
0.1μF
XFP Module
0.1μF
VEE5
Optional
Host -5.2V
4.7μH
0.1μF
22μF
0.1μF
Recommended Interface Circuit
XFP module
Host Board
TD +
SerDat Out+
Z=50Ω
CML
TD -
SerDat Out-
100Ω
CML
Z=50Ω
RD +
SerDat In+
CML
100Ω
Z=50Ω
SerDat In-
CML
RD Z=50Ω
Vcc(+3.3V)
4.7K to 10KΩ
REFCLKP
100Ω
REFCLKN
RX_LOS
INTERRUPT
SDA
VCC(+3.3V)
SCL
MOD_NR
10KΩ
MOD_abs
TX_DIS
GND
MOD_DeSel
P_Down/RST
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2008
V1.0
Optoway
XPS-2310W-CXX0G
8
***********************************************************************************************************************************************************************
Table 2 Serial ID Memory Contents (Table 01h)
Address
Field
Size
(Byte)
128
1
Identifier
129
130
131~138
139
140
141
142
143
144
145
146
147
1
1
8
1
1
1
1
1
1
1
1
1
Ext. Identifier
Connector type
Transceiver
Encoding
BR-Min
BR-Max
length (SMF)-Km
Length (E-50µm)
Length (50 µm)
Length (62.5 µm)
Length (Copper)
Device Tech
148~163
164
165~167
16
1
3
Vendor name
CDR Support
Vendor OUI
168~183
16
Vendor PN
184~185
2
Vendor rev
186~187
2
188~189
190
191
192~195
2
1
1
4
Wavelength
Wavelength
Tolerance
Max Case Temp
CC_BASE
Power Supply
196~211
16
Vendor SN
212~219
8
220
1
Date code
Diagnostic
Monitoring Type
Name of Filed
Description
Hex
XFP
power consumption <2.5W, no Ref Colck
required
LC connector
10GBASE-LR/LW, 10GFC 1200-SM-LL-L
64B/66B, 8B10B, NRZ
9.9Gbps
10.5Gbps
10 Km
0m
0m
0m
0m
Uncooled CWDM DFB, PIN detector
06
+/- 6.5nm
70deg
Check sum of Byte 128 -- 190
2Wmax, 1.5W pd_max , 550mA 3.3V
05 14
46
50
07
44 40 00 00 00 00 00 00
D0
63
69
0A
00
00
00
00
50
4F 50 54 4F 57 41 59 20
OPTOWAY
20 20 20 20 20 20 20 20
CDR supports 9.953G ~ 10.52G, XFI Loopback E1
00 0E FA
XPS-2310W-CXX0G
XX = 27, 29, 31, 33, 35, 37, 39, 41, 43, 45, 47, 58 50 53 2D 32 33 31 30
49, 51, 53, 55, 57, 59, 61
57 2D 43 xx xx 30 47 20
ASCII (“31 61” means 1a revision)
xx xx
1XX1nm, XX=27,2 9, 31, 33, 35, 37, 39, 41, 43,
45, 47, 49, 51, 53, 55, 57, 59, 61
xx xx
ASCII
ASCII Year (2 Byte), Month (2 Byte), Day (2
Byte)
No BER Support, Average Power
Optional Soft TX_DISABLE implemented,
Optional Soft P_down implemented
AUX1 for Vcc3.
Check sum of Byte 192 -- 222
221
1
Enhanced Options
222
1
Aux Monitoring
223
1
CC_EXT
224~255
32
Vendor Specific
Note: Specifications subject to change without notice.
64 96 06 00
xx xx xx xx xx xx xx xx
xx xx xx xx xx xx xx xx
xx xx xx xx xx xx 20 20
08
60
70
Reserved
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2008
V1.0
Optoway
XPS-2310W-CXX0G
9
***********************************************************************************************************************************************************************
Revision History
Version
1.0
Subject
Release Date
Initial datasheet
2008/2/1
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
2/1/2008
V1.0