Hebei I.T. (Shanghai) Co., Ltd. LED SPECIFICATION Part No./型号：3751PG2D-SB 3.1 3.9 3.1 9.8±0.5 z Single color/单色 z High bright output/高亮度输出 z Low power consumption/低功耗 6.3 ¾ Features/特征： ¾ Descriptions/描述： z Dice material/芯片材质：GaN z Emitting Color/发光颜色： 25.4Min 1.1±0.1 1±0.1 1.5±0.5 CATHODE 可靠性高、寿命长 0.8Max z High reliability and long life/ 0.5±0.1 Super Bright Green/ 高亮度绿色 2.54±0.1 z Device Outline/产品外形： 3.9×3.1mm Oval Type / 3.9×3.1mm 椭圆形 z Lens Type 胶体颜色： NOTE/备注: 1. All dimensions are millimeters/单位：mm. 2. Tolerance is +/-0.25mm unless otherwise noted/ 没有标注的公差均为±0.25mm. Green Diffused / 绿色散射 ¾ Directivity/指向特性： DIRECTIVITY 0° 1.0 Relative Luminous Y Ta=25° C X IF=20mA Y 60° 0.5 0 X 30° 90° 60° 30° 0° 0.5 90° 1.0 Radiation Angle www.ledz.com 1/6 Hebei I.T. (Shanghai) Co., Ltd. LED SPECIFICATION Part No./型号：3751PG2D-SB ¾ Absolute maximum ratings/极限参数（Ta = 25℃） Parameter 参数 Reverse Voltage 反向电压 Forward Current 正向工作电流 Power Dissipation 损耗功率 Pulse Current 正向峰值电流 Operating Temperature 工作温度范围 Storage Temperature 储存温度范围 Values 数值 Min. Max. Symbol 符号 Test Condition 测试条件 Unit 单位 VR IR = 30μA 5 -- V IF ---- ---- 25 mA Pd ---- ---- 90 mW Ipeak Duty=0.1mS，1kHz ---- 100 mA Topr ---- -30 +85 ℃ Tstr ---- -40 +100 ℃ ¾ Electrical and optical characteristics/光电参数（Ta = 25℃） Parameter 参数 Forward Voltage 正向电压 Reverse Current 反向电流 Dominate Wavelength 主波长 Peak Wavelength 峰值波长 Spectral Line half-width 半波长宽度 Luminous Intensity 发光强度 Viewing Angle 指向角度 Values 数值 Typ. Max. Symbol 符号 Test Condition 测试条件 Min. VF IF=20mA ---- 3.2 3.6 V IR VR=5V ---- ---- 30 μA λd IF=20mA ---- 528 ---- nm λp IF=20mA ---- 525 ---- nm Δλ IF=20mA ---- 35 ---- nm IV IF=20mA ---- 1200 ---- mcd 2θ1/2 IF=20mA ---- 85/40 ---- deg. ¾ Luminous Intensity Bins/亮度等级分档（Ta = 25℃） Bin Min Max T 1100 1520 G11 521 524 G12 524 527 V8 3.0 3.2 V9 3.2 3.4 Unit:nm G13 527 530 ¾ Forward Current Bins/电压等级分档（Ta = 25℃） Bin Min Max Unit:mcd P 1520 2130 ¾ Dominate Wavelength Bins/波长等级分档（Ta = 25℃） Bin Min Max Unit 单位 Unit:V V10 3.4 3.6 www.ledz.com 2/6 Hebei I.T. (Shanghai) Co., Ltd. LED SPECIFICATION Part No./型号：3751PG2D-SB ¾ Typical electrical/optical characteristic curves/光电特性曲线： Fig.1 正向电流 Vs. 正向电压 Fig.2 相对亮度 Vs. 正向电流 2.5 Luminous Intensity Relative Value at IF=20mA Forward Current(mA) 50 40 30 20 10 0 2.4 2.8 3.2 3.6 4.0 Forward Voltage(V) Relative Luminous Intensity 20 10 60 80 0 40 10 20 30 IF-Forward Current (mA) 50 2.5 2.0 1.5 1.0 0.5 0 -40 100 Ambient Temperature T A (℃) -20 0 20 40 60 Ambient Temperature T A (℃) 80 90 Fig.5 相对亮度 Vs. 波长 Relative Luminous Intensity Forward Current(mA) 30 40 0.5 Fig.4 相对亮度 Vs. 环境温度 40 20 1.0 0 Fig.3 正向电流 Vs. 环境温度 0 1.5 4.4 50 0 2.0 100 75 50 25 0 400 450 500 550 600 650 700 Wavelength λ(nm) www.ledz.com 3/6 Hebei I.T. (Shanghai) Co., Ltd. LED SPECIFICATION Part No./型号：3751PG2D-SB ¾ Lead Forming/成形 1. Any lead forming or bending must be done before soldering. 支架成形必须在焊接前完成。 2. When forming leads, there must be a minimum of 2mm clearance between the base of the LED lens and the lead bend. 必需离胶体 2 毫米才能折弯支架。 3. Avoid bending the leads at the same point more than once. 避免在管脚同一位置两次或多次弯。 4. During assembly onto PCB, the lead pitch of the LED must match the pitch of the mounting holes on the PCB during component placement. 支架成形需保证引脚和间距与线路板上一致。 ¾ Soldering Condition/焊接条件 Careful attention should be paid during soldering. When soldering, leave more then 2mm from solder joint to case, and soldering beyond the base of the tie bar is recommended. 焊接时请特别注意，焊接点要离LED封装体底部2mm以上。 Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering. 在 LED 处于高温，特别是在焊接时，请避免对支架施压。 www.ledz.com 4/6 Hebei I.T. (Shanghai) Co., Ltd. LED SPECIFICATION Part No./型号：3751PG2D-SB Recommended soldering conditions/推荐焊接条件: Hand Soldering 手工焊接 Temp.at tip of iron 300℃Max.(30WMax.) 电烙铁温度 最高温度300℃（功率 不超过30瓦） Soldering time 3 sec Max. 焊接时间 时间不超过3秒 Distance 2mm Min.(From 焊接位置 solder joint to case) 大于2毫米（从焊点到 胶体） DIP Soldering 浸焊 Preheat temp. 100℃ Max. (60 sec Max.) 预热温度 最高温度100℃（不超过60 秒） Bath temp. 260℃ Max 浸焊温度 最高260℃. Bath time. 3 sec Max. 浸焊时间 不超过3秒 Distance 浸焊位置 2mm Min 大于2毫米. ¾ Cleaning/清洗 1. Do not clean LEDs with water, Alcohol are recommended solvents for cleaning. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not. 不要用水清洗，推荐使用酒精清洗，当使用其他溶剂清洗时应事先确认该溶剂是否溶解树脂。 2. LEDs may be damaged by ultrasonic-washed. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. LED有可能在超声波清洗过程中被破坏。为了保证安全，在清洗前，请先确认。 ¾ Storage/保存 1. Environmental temperature: -40℃---100℃, Recommended: -20℃---50℃ 环境温度：-40℃---100℃，推荐使用-20℃---50℃； 2. Environmental humidity: 30%---70%, Recommended: 40%---60% 环境湿度：30%---70%，推荐使用40%---60%； www.ledz.com 5/6 Hebei I.T. (Shanghai) Co., Ltd. LED SPECIFICATION Part No./型号：3751PG2D-SB ¾ Static Electricity/静电 1. Static Electricity or power surge will damage the LED. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. 静电或激增电压将损害 LED。 建议使用发光二极管时佩戴手腕带或防静电手套。 2. All production machinery and test instruments must be electrically grounded. 所有的生产机器和检测仪器，必须接地。 3. Maintain a humidity level of 50% or higher in production areas. 生产现场湿度必须保持在50%或者更高。 4. Use anti-static packaging for transport and storage. 使用防静电包装，运输和储存。 ¾ Notes/备注 1. This datasheet will be update regularly, if there comes out any changes, pls confirmed by the latest datasheet. 以上规格书会定期进行更新，如有改动,以最新规格书为准。 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. HEBEI assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 在使用本产品时，请注意参考规格书中的最大额定值和使用说明，如果没有遵照产品规格书中 的最大额定值以及使用说明而产生的不良后果，不在赫备承诺范围之内。 www.ledz.com 6/6