2 W Conductive Plastic Potentiometers 380 Series, RV4 Series, 485 Series, 53C Series, 385 Series Datasheet Conductive Plastic Potentiometers Potentiometers convert rotary motion into a change of resistance, supplying a smooth transition of voltage or current levels. The resulting voltage output may be used to control position transducers in a wide variety of potential applications. The five series listed below are all 2 W plastic potentiometers and are available in resistances from 100 Ohm to 5 MOhm, inclusive. Available tapers include linear, log, and antilog to meet a wide range of application requirements. These single turn devices have a 6,35 mm [0.250 in] diameter shaft that is available in a range of lengths. Most shafts are nickel-plated brass. Most configurations have a standard 3/8-32 NEF-2A bushing; a high torque version is also available. Termination types are solder lug (with or without a center tap), PC pin or fast-on, all are solder-dipped. Custom designs are available upon request. , • 380 Series: 2 W conductive plastic potentiometer offering low contact resistance variation and a long rotational life • RV4 Series: Military version of the 380 Series; meets MIL-R-94 requirements (non RoHS compliant) • 485 Series: Custom version of the 380 Series • 53C Series: Cost-effective version of the 380 Series • 385 Series: Custom version of the 53C Series Key Features and Benefits Table of Contents • Cost-effective: Supplies good performance at a reasonable price General Specifications. . . . . . . . . . . . . . . . . . 3-6 General Configuration Guide . . . . . . . . . . . . . . 7 380 Series: • Wide range of resistance values (100 Ohm to 5 MOhm, inclusive): Promotes flexibility in the applications • Wide variety of tapers: Creates flexibility in output signal profile, allowing use in a wide variety of applications Specific Configurations. . . . . . . . . . . . . . . . . 8 Order Guides. . . . . . . . . . . . . . . . . . . . . . . 9-15 RV4 Series: Specific Configurations. . . . . . . . . . . . . . . . . 16 Order Guides. . . . . . . . . . . . . . . . . . . . . . 17-18 485 Series: Potential Applications INDUSTRIAL/COMMERCIAL • sound mixers, projectors, amplifiers) • 53C Series: Foot pedal controls (e.g., guitars, sewing machines, woodworking equipment) Specific Configurations. . . . . . . . . . . . . . 19-21 Order Guides. . . . . . . . . . . . . . . . . . . . . . 22-31 Audio and visual equipment (e.g., musical instruments, • Machine controls (e.g., joysticks) • Welding equipment (e.g., MIG wire feed, foot pedal controls, adjustment knobs) Specific Configurations. . . . . . . . . . . . . . . . 32 Order Guides. . . . . . . . . . . . . . . . . . . . . . 33-37 385 Series: Specific Configurations. . . . . . . . . . . . . . 38-39 Transportation • Foot pedal controls (e.g., golf carts) • Gear shifter, joystick, and throttle position (e.g., construction/ agricultural vehicles) Order Guides. . . . . . . . . . . . . . . . . . . . . . 40-46 Additional Information. . . . . . . . . . . . back page Cost-EffecTIVE • MIL-R-94 • Customization AvaiLable 2 sensing.honeywell.com General Specifications Table 1. Electrical Specifications Characteristic 380 Series RV4 Series Maximum working voltage: linear tapers log, reverse log tapers 485 Series 53C Series 385 Series 500 Vdc 350 Vdc Dielectric strength 1000 Vac for 60 s at 1 mPa [atm], 450 Vac for 60 s at 11,5 kPa [3.4 inHg] Power rating 2 W at 70 °C [158 °F], derated to 120 °C [248 °F] Taper See Order Guides under each series CRV : linear tapers log, reverse log tapers 1 3% max. total resistance 3% max. total resistance Resistance 100 Ohm to 5 MOhm, inclusive. See individual Order Guides under each series. Resistance tolerance See Order Guides under each series. End resistance See Order Guides under each series. ±5% Linearity Electrical rotation See Order Guides under each series. Contact resistance variation is the maximum momentary change in contact resistance that occurs when the wiper is moved from one location to another location. The larger this change, the more difficult it is to set the trimmer potentiometer and the more unstable the long term setting will be. 1 Table 2. Mechanical Specifications Characteristic 380 Series RV4 Series 485 Series Shaft: material diameter Retaining ring material 385 Series nickel-plated brass1 6,35 mm [0.250 in] nickel-plated beryllium copper nickel-plated brass Bushing: material thread nickel-plated brass nickel-plated brass 3/8-32 NEF-2A Termination base material Terminal material 53C Series thermoset brass; solder (SAC305) dip finish brass; solder (SAC305) dip or tin-lead finish Housing material brass; solder (SAC305) dip finish brass; solder (SAC305) dip or tin-lead finish stainless steel Base material thermoset plastic Mounting hardware material: jam nut mounting nut lock washer o-ring nickel-plated brass nickel-plated brass nickel-plated brass phospher bronze1 silicone rubber Operating torque See Order Guides under each series. Stop torque See Order Guides under each series. Weight (approx.) 32.7 g [0.072 lb] Unless otherwise specified on the Order Guides under each series. 1 sensing.honeywell.com 3 General Specifications Table 3. Environmental Specifcations Characteristic 380 Series RV4 Series Operating temperature 485 Series 53C Series 385 Series -55 °C to 120 °C [-67 °F to 248 °F] Rotational life tested to 25,000 cycles Table 4. Maximum Percent Temporary Resistance from 25 °C [77 °F] Nominal Resistance Temperature -55 °C [-67 °F] -40 °C [-40 °F] 0 °C [32 °F] 25 °C [77 °F] 55 °C [131 °F] 85 °C [185 °F] 120 °C [248 °F] 100 Ohm ±5.0 ±4.0 ±1.5 0 ±1.5 ±2.0 ±3.5 10 kOhm +7.0 +5.5 +2.0 0 ±1.5 ±2.5 ±5.5 100 kOhm +8.0 +6.0 +2.5 0 ±2.0 ±3.5 ±6.0 1 MOhm +10.0 +8.0 +3.0 0 ±2.5 ±4.0 ±7.5 Figure 1. Electrical Taper Diagrams (For reference only.) Log (Z) Reverse Log (RZ) 90 80 80 80 70 60 50 40 30 Total Resistance (%) 90 Total Resistance (%) 100 90 Total Resistance (%) 100 70 60 50 40 30 70 60 50 40 30 20 20 20 10 10 10 0 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 5% to 95% (S-2) 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 7.5% to 92.5% (S-3) 90 90 80 80 80 60 50 40 30 Total Resistance (%) 100 90 Total Resistance (%) 100 70 70 60 50 40 30 60 50 40 30 20 20 10 10 10 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) sensing.honeywell.com 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 70 20 0 0 Linear: 10% to 90% (S-4) 100 Total Resistance (%) 4 Linear: 2.5% to 97.5% (S-1) 100 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) General Specifications Figure 1. Electrical Taper Diagrams (continued) Linear: 15% to 95% (S-5) Linear: 25% to 75% (S-6) Linear: 35% to 65% (S-7) 90 90 80 80 80 70 60 50 40 30 Total Resistance (%) 100 90 Total Resistance (%) 100 Total Resistance (%) 100 70 60 50 40 30 70 60 50 40 30 20 20 20 10 10 10 0 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 37.5% to 82.5% (S-8) 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 42.5% to 57.5% (S-9) 80 80 60 50 40 30 Total Resistance (%) 90 80 Total Resistance (%) 100 90 Total Resistance (%) 100 90 70 60 50 40 30 70 60 50 40 30 20 20 20 10 10 10 0 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 5% to 50%; 50% to 90% (S-11) 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 80 80 50 40 Total Resistance (%) 90 80 Total Resistance (%) 100 90 Total Resistance (%) 100 90 60 70 60 50 40 60 50 40 30 20 20 20 10 10 10 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 35% to 45%; 55% to 65% (S-14) 0 30 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 45% to 47.5%; 47.5% to 52.5%; 52.5% to 55% (S-15) 80 80 60 50 40 30 Total Resistance (%) 90 80 Total Resistance (%) 100 90 Total Resistance (%) 100 90 70 60 50 40 30 60 50 40 30 20 20 10 10 10 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 70 20 0 0 Linear: 5% to 40%; 45% to 52.5%; 60% to 95% (S-16) 100 70 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 70 30 0 0 Linear: 10% to 40%; 57.5% to 82.5% (S-12) Linear: 10% to 45%; 55% to 90% (S-13) 100 70 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 45% to 55% (S-10) 100 70 0 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) sensing.honeywell.com 5 General Specifications Figure 2. Power Derating Curve 100 90 80 Rated Power (%) 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 Temperature (°C) 90 100 110 120 Figure 3. Mounting Hardware 6 Jam Nut Mounting Nut Lock Washer O-Ring 7,94 mm [5/16 in] across flats 3,97 mm [5/32 in] thick 1/4 x 32 thread 7,94 mm [5/16 in] across flats 10,32 mm [5/16 in] outside diameter 0,64 mm [0.025 in] thick 6,35 mm [0.25 in] outside diameter 1,78 mm [0.070 in] thick sensing.honeywell.com General Configuration Guide Figure 4. General Configuration Guide This figure shows possible configurations. Not all combinations may be available, please contact Honeywell. See the Order Guides for each series on subsequent pages for currently available catalog listings. Resistance Product Series Bushing Type and Length 380 Series, 3/8-32 NEF-2A: Standard: RV4 Series, 6,35 mm [0.25 in] 485 Series, 53C Series, 385 Series 2W Conductive Plastic 7,92 mm [0.312 in] Potentiometers Switch Shaft Type None ø3,18 mm [0.125 in]: Flatted Number Signifi- of Zeros that cant Follow Digit Shaft Length 10 Ohm 0 12,7 mm [0.50 in] 15 Ohm 1 15,88 mm [0.625 in] 20 Ohm 2 19,05 mm [0.75 in] 25 Ohm 3 22,23 mm [0.875 in] 50 Ohm 4 9,53 mm [0.325]1 1 Round 5 31,75 mm [1.25 in] No locating pins 10% to 90% One locating pin: 9 o’ clock 15% to 95% Solder lug with center tap 3 o’ clock PC pin 42.5% to 57.5% Applies to 6,25 mm [0.25 in] bushings only. 1 Solder lug 7.5% to 92.5% 37.5% to 82.5% Custom Termination Type 5% to 95% 35% to 65% 63,5 mm [2.50 in] 8,69 mm [0.342 in] Linear: 2.5% to 97.5% Anti-Rotation (AR) Locating Pin 25% to 75% 50,8 mm [2.00 in] Slotted Electrical Taper 45% to 55% 5% to 50%; 50% to 90% Straight Knurled Two locating pins Fast-on 10% to 40%; 57.5% to 82.5% 9,27 mm [0.365 in] 10% to 45%; 55% to 90% 10% to 45%; 55% to 90% Custom Custom Custom 35% to 45%; 55% to 65%; 9,53 mm [0.375 in] 45% to 57.5%; 52.5% to 55%; General 380 Series, RV4 Series, 485 Series, 53C Series, 385 Series Terminology 12,7 mm [0.500 in] Log Jam nut Reverse Log Custom Mounting nut High Torque: 12,7 mm [0.500 in] Lock washer 5% to 40%; 45% to 52.5%; 60% to 95% Mounting hardware O-ring Custom Locating pin Termination Shaft Bushing sensing.honeywell.com 7 380 Series Specific Configurations Table 5. 380 Series Specific Configurations Shaft Type Bushing AR Type Pin Termination 380-A (See Table 380-A on p. 9.) flatted standard, 9,53 mm [0.375 in] 1 solder lug 380-C (See Table 380-C on p. 10.) flatted standard, 9,53 mm [0.375 in] 1 PC pin 380-E (See Table 380-E on p. 12.) high torque, slotted 12,7 mm [0.500 in] 1 solder lug 380-G (See Table 380-G on p. 14.) slotted standard, 9,53 mm [0.375] in 1 solder lug 380-I (See Table 380-I on p. 15.) slotted 8 standard, 9,53 mm [0.375] in 2 sensing.honeywell.com solder lug Configuration with Associated Hardware Shaft Type Bushing Type AR TerminPin ation 380-B (See Table 380-B on p. 10.) slotted standard, 9,53 mm [0.375 in] 2 solder lug 380-D (See Table 380-D on p. 11.) round standard, 9,53 mm [0.375 in] 1 solder lug 380-F (See Table 380-F on p. 13.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 380-H (See Table 380-H on p. 14.) slotted standard, 9,53 mm [0.375] in 1 fast-on Configuration with Associated Hardware 380 Series Order Guides Table 380-A Order Guide Dimensions RoHS Compliant Bushing Length (mm [in]) Shaft Seal Shaft Length (mm [in]) Stop Torque (N m [in-lb]) Flat Thickness (mm [in]) Operating Torque (mN m [in-oz]) Mounting Hardware 380000M8629 1k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 7,95 5,54 19,46 9,53 [0.313] [0.218] [0.766] [0.375] yes unassembled 380000M8630 2.5 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 7,95 5,54 19,46 9,53 [0.313] [0.218] [0.766] [0.375] yes unassembled 380000M8643 1k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 14,30 5,54 25,4 9,53 [0.563] [0.218] [1.000] [0.375] yes unassembled 380000M8682 50 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 7,95 5,54 19,46 9,53 [0.313] [0.218] [0.766] [0.375] yes unassembled 380017M00071,2 500 10 4 4 274 312 S-4 312 6 [7-42] 12 [1.4] yes 7,95 5,54 22,23 9,53 [0.313] [0.218] [0.875] [0.375] no unassembled 380017M8606 10 k 10 4 4 274 312 S-4 312 6 [7-42] 12 [1.4] yes 7,95 5,54 19,05 9,53 [0.313] [0.218] [0.750] [0.375] yes unassembled 380017M87681 25 k 10 4 4 274 312 S-4 312 6 [7-42] 12 [1.4] yes 7,95 5,54 19,05 9,53 [0.313] [0.218] [0.750] [0.375] yes unassembled 380017M95501 5k 10 4 4 274 312 S-4 312 6 [7-42] 12 [1.4] yes 7,95 5,54 19,05 9,53 [0.313] [0.218] [0.750] [0.375] yes unassembled Catalog Listing End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Mechanical Rotation (Degree) D Taper C Electrical Rotation, ±3 (Degree) B Resistance Tolerance (±%) A Flat Length (mm [in]) Mechanical Resistance (Ohm) Electrical Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C D A 3,18 [0.125] B Locating pin ø6,35 3X 1,57 [0.062] Terminal base 0,635 [0.025] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] [0.250] 3/8-32 NEF-2A Mounting surface 3,18 Min. [0.125] 22,25 Max. [0.875] 90° 1 Left 3 2 Right Center 2X 20° Supplied with nickel-plated, phosphor bronze lock washer. Supplied with two mounting nuts. 1 2 sensing.honeywell.com 9 380 Series Order Guides Table 380-B Order Guide yes 7.95 5,54 19,05 9,53 [0.313] [0.218] [0.750] [0.375] RoHS Compliant 12 [1.4] Mounting Hardware yes unassembled RoHS Compliant 1-6 [7-42] D Bushing Length (mm [in]) 312 C Shaft Length (mm [in]) Shaft Seal S-4 B Flat Thickness (mm [in]) Stop Torque (N m [in-lb]) 312 274 A Flat Length (mm [in]) Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 10 k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 3800017M8956 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes none Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C D 2,77 [0.109] A 2X 3,18 [0.125] B Locating pin ø6,35 3X 1,57 [0.062] Terminal base 3X 1,57 [0.062] 22,25 Max. [0.875] 3/8-32 NEF-2A 90° Mounting surface 0,635 [0.025] 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] [0.250] 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 380-C Order Guide 1-6 [7-42] 12 [1.4] yes D Bushing Length (mm [in]) 312 C Shaft Length (mm [in]) Shaft Seal S-2 B Flat Thickness (mm [in]) Stop Torque (N m [in-lb]) 312 288 A Flat Length (mm [in]) Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 10 k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 380096M9088 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical 9,53 5,54 22,23 9,27 [0.375] [0.218] [0.875] [0.365] Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C D 2,77 [0.109] A B Locating pin 3,18 [0.125] 13,87 [0.546] ø6,35 [0.250] Terminal base 3/8-32 NEF-2A 32,77 Max. [1.290] 90° Mounting surface 3X 1,57 [0.062] 3X 1,02 [0.040] 10 sensing.honeywell.com 2X 5,08 [0.200] 0,635 [0.025] 3,18 Min. [0.125] 3 1 2 Left Center Right 380 Series Order Guides Table 380-D Order Guide Dimensions Mechanical Rotation (Degree) Operating Torque (mN m [in-oz]) Stop Torque (N m [in-lb]) Shaft Seal Shaft Length (mm [in]) Bushing Length (mm [in]) RoHS Compliant Mounting Hardware 380C1100 100 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000]) 9,53 [0.375] yes unassembled 380C11000 1000 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C1100K 100 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C110K 10 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C11MEG 1M 10 10 10 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C12000 2k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C120K 20 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] no unassembled 380C1250 250 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C12500 2.5 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C125K 25 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C135K 35 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C1500 500 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C15000 5k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C1500K 500 k 10 10 10 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled 380C150K 50 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 50,8 [2.000] 9,53 [0.375] yes unassembled Catalog Listing End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Taper B Electrical Rotation, ±3 (Degree) A Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] A B 2,77 [0.109] 3,18 [0.125] Locating pin [0.250] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 0,635 [0.025] 22,25 Max. [0.875] 3/8-32 NEF-2A Mounting surface 3,18 Min. [0.125] 1 Left 3 2 Right Center 2X 20° sensing.honeywell.com 11 380 Series Order Guides Table 380-E Order Guide RoHS Compliant Bushing Length (mm [in]) Shaft Seal Shaft Length (mm [in]) Stop Torque (N m [in-lb]) 380C2000 1k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 15,88 12,7 [0.063] [0.047] [0.625] [0.500] yes unassembled 380C210K 10 k 10 4 4 274 312 S-4 312 1-4 [7-28 12 [1.4] no 1,60 1,19 15,88 12,7 [0.063] [0.047] [0.625] [0.500] yes unassembled 380C225K 25 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 15,88 12,7 [0.063] [0.047] [0.625] [0.500] yes unassembled 380C25000 5k 10 4 4 274 312 S-4 312 1-4 [7-28 12 [1.4] no 1,60 1,19 15,88 12,7 [0.063] [0.047] [0.625] [0.500] yes unassembled Slot Depth (mm [in]) Operating Torque (mN m [in-oz]) Mounting Hardware End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Catalog Listing Mechanical Rotation (Degree) D Taper C Electrical Rotation, ±3 (Degree) A Resistance Tolerance (±%) B Slot Width (mm [in]) Dimensions Mechanical Resistance (Ohm) Electrical Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] C ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] A 90° 3,18 [0.125] Locating pin ø6,35 3X 1,57 [0.062] 12 sensing.honeywell.com 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] B 22,25 Max. [0.875] Mounting surface 0,635 [0.025] 2X 20° 12,87 [0.546] [0.250] 3X 1,57 [0.062] 3,18 Min. [0.125] 1 Left 3 2 Right Center 380 Series Order Guides Table 380-F Order Guide RoHS Compliant Bushing Length (mm [in]) Shaft Seal Shaft Length (mm [in]) Stop Torque (N m [in-lb]) 380C3100 100 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C31000 1k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C3100K 100 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C310K 10 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C31MEG 1M 10 10 10 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C32000 2k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C3200K 200 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] no unassembled 380C3250 250 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] no unassembled 380C32500 2.5 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C3250K 250 k 10 10 10 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C325K 25 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C3500 500 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C35000 5k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C3500K 500 k 10 10 10 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380C350K 50 k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled Slot Length (mm [in]) Operating Torque (mN m [in-oz]) Mounting Hardware Catalog Listing End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Mechanical Rotation (Degree) D Taper C Electrical Rotation, ±3 (Degree) B Resistance Tolerance (±%) A Slot Width (mm [in]) Dimensions Mechanical Resistance (Ohm) Electrical Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. [1.094] 13,49 [0.531] C D 90° A 3,18 [0.125] Locating pin 3X 1,57 [0.062] 3X 1,57 [0.062] [0.250] Terminal base 0,635 [0.025] 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø27,79 3/8-32 NEF-2A Mounting surface 3,18 Min. [0.125] B 22,25 Max. [0.875] 1 Left 3 2 Right Center 2X 20° sensing.honeywell.com 13 380 Series Order Guides Table 380-G Order Guide RoHS Compliant 10 274 312 Z 312 1-6 [7-42] 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled 380101M96991,2 2.5 M 10 25 10 274 312 Z 312 1-6 [7-42] 12 [1.4] yes 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] yes unassembled RoHS Compliant BusingLength (mm [in]) Shaft Seal 5 Mounting Hardware yes unassembled Slot Depth (mm [in]) Stop Torque (N m [in-lb]) 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 3800000748500058 500 k Resistance Tolerance (±%) Mounting Hardware Catalog Listing Resistance (Ohm) Operating Torque (mN m [in-oz]) D Mechanical Rotation (Degree) C Taper B Electrical Rotation, ±3 (Degree) A Shaft Length (mm [in]) Dimensions Mechanical Slot Width (mm [in]) Electrical Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] C D 90° 2,77 [0.109] A ø27,79 Max. [1.094] 13,49 [0.531] 3,18 [0.125] 3X 1,57 [0.062] Locating pin 3X 2,36 [0.093] 3X 3,15 [0.124] ø6,35 Mounting surface 0,635 [0.025] 2X 20° B 3/8-32 NEF-2A Terminal base 3X 1,57 [0.062] 12,87 [0.546] [0.250] 22,25 Max. [0.875] 1 Left 3 2 Center Right 3,18 Min. [0.125] Supplied with stainless-steel shaft. Supplied with nickel-plated beryllium copper retaining ring. 1 2 Table 380-H Order Guide D Bushing Length (mm [in]) no C Shaft Length (mm [in]) 6-20 12 [42-141] [1.4] B Slot Width (mm [in]) 312 Slot Length (mm [in]) S-2 Operating Torque (mN m [in-oz]) 312 Shaft Seal 288 A Stop Torque (N m [in-lb]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 1k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 380099M9425 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] C D ø27,79 Max. [1.094] 13,49 [0.531] 90° 2,77 [0.109] A 3,18 [0.125] Locating pin 3X 1,57 [0.062] 3X 1,27 [0.050] 3X ø1,14 [0.045] 3X 3,96 [0.156] 3X 2,79 [0.110] 14 sensing.honeywell.com 3X 1,73 [0.068] 2X 20° 12,87 [0.546] ø6,35 [0.250] Terminal base 0,56 [0.022] B 27,38 Max. [1.078] 3/8-32 NEF-2A Mounting surface 1 Left 3,18 Min. [0.125] 3 2 Right Center 380 Series Order Guides Table 380-I Order Guide 12 [1.4] no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] RoHS Compliant 1-4 [7-28] D Bushing Length (mm [in]) 360 C Shaft Length (mm [in]) Shaft Seal S-3 B Slot Width (mm [in]) Stop Torque (N m [in-lb]) 344 310 Slot Depth (mm [in]) Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 A Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 1k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 380036M7444 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] C D ø27,79 Max. [1.094] 13,49 [0.531] 90° 2,77 [0.109] A 3,18 [0.125] Locating pin 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] ø6,35 12,87 [0.546] [0.250] Terminal base 0,635 [0.025] 3/8-32 NEF-2A B 22,25 Max. [0.875] Mounting surface 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° sensing.honeywell.com 15 RV4 Series Specific Configurations Table 6. RV4 Series Specific Configurations Shaft Type Bushing AR Type Pin Termination RV4-A (See Table RV4-A on p. 17.) high torque, slotted 12,7 mm [0.500 in] 16 1 sensing.honeywell.com solder lug Configuration with Associated Hardware Shaft Type Bushing Type AR TerminPin ation RV4-B (See Table RV4-B on p. 18.) standard, slotted 9,53 mm [0.375 in] 1 solder lug Configuration with Associated Hardware RV4 Series Order Guides Table RV4-A Order Guide Electrical Dimensions Mechanical Effective Electrical Rotation, Typ. (Degree) Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) Stop Torque (N m [in-lb]) Shaft Seal RoHS Compliant Mounting Hardware RV4LAYSD102A 1k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 12,7 [0.500] no unassembled RV4LAYSD103A 10 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 12,7 [0.500] no unassembled RV4LAYSD104A 100 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 12,7 [0.500] no unassembled RV4LAYSD502A 5k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 12,7 [0.500] no unassembled RV4LAYSD504A 500 k 10 10 10 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 12,7 [0.500] no unassembled Catalog Listing Operating Torque (mN m [in-oz]) End Resistance at CCW, Max. (Ohm) Bushing Length (mm [in]) End Resistance at CW, Max. (Ohm) Shaft Length (mm [in]) Resistance Tolerance (±%) B Resistance (Ohm) A Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] 11,9 [0.047] A B 1,6 [0.063] 3,18 [0.125] ø12,7 [0.500] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] ø6,35 [0.250] Locating pin 3/8-32 NEF-2A Terminal base Mounting surface 0,64 [0.025] 3,18 Min. [0.125] 12,87 [0.546] 22,23 Max. [0.875] 90° 1 Left 3 Right 2 Center 2X 20° sensing.honeywell.com 17 RV4 Series Order Guides Table RV4-B Order Guide Dimensions Mechanical Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) Stop Torque (N m [in-lb]) Shaft Seal RoHS Compliant Mounting Hardware RV4NAYSB101A 100 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] yes 12,7 [0.500] 9,53 [0.375] no unassembled RV4NAYSB103A 10 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] yes 12,7 [0.500] 9,53 [0.375] no unassembled RV4NAYSB503A 50 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] yes 12,7 [0.500] 9,53 [0.375] no unassembled RV4NAYSK103A 10 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] yes 63,5 [2.500] 9,53 [0.375] no unassembled RV4NAYSK502A 5k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] yes 63.5 [2.5,0] 9,53 [0.375] no unassembled RV4SAYSD502A 5 10 - - 274 312 S-4 312 1-6 12 [7-42] [1.4] yes 22,23 [0.875] 9,53 [0.375] no unassembled RV4NAYSD503D 50 k 20 500 4 274 312 Z 312 1-6 12 [7-42] [1.4] yes 22,23 [0.875] 9,53 [0.375] no unassembled Catalog Listing Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) Bushing Length (mm [in]) End Resistance at CCW, Max. (Ohm) Shaft Length (mm [in]) End Resistance at CW, Max. (Ohm) B Resistance Tolerance (±%) A Resistance (Ohm) Electrical Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] A Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B 2,77 [0.109] ø6,35 [0.250] Locating pin 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 18 sensing.honeywell.com 3/8-32 NEF-2A Terminal base Mounting surface 0,64 [0.025] 2X 20° 12,87 [0.546] 22,23 Max. [0.875] 90° 1 Left 3,18 Min. [0.125] 3 Right 2 Center 485 Series Specific Configurations Table 7. 485 Series Specific Configurations Shaft Type Bushing AR Type Pin Termination 485-A (See Table 485-A on p. 22) flatted standard, 9,53 mm [0.375 in] 1 solder lug 485-C (See Table 485-C on p. 23.) round standard, 6,35 mm [0.250 in] 1 solder lug with center tap 485-E (See Table 485-E on p. 24.) round standard, 9,53 mm [0.375 in] 1 solder lug 485-G (See Table 485-G on p. 25.) round standard, 9,53 mm [0.375 in] 1 solder lug Configuration with Associated Hardware Shaft Type Bushing Type AR TerminPin ation Configuration with Associated Hardware 485-B (See Table 485-B on p. 22.) flatted standard, 9,53 mm [0.375 in] 1 solder lug with center tap 485-D (See Table 485-D on p. 23.) round standard, 9,53 mm [0.375 in] 1 solder lug 485-F (See Table 485-F on p. 24.) round standard, 9,53 mm [0.375 in] 1 solder lug 485-H (See Table 485-H on p. 25.) standard, slotted 9,53 mm [0.375 in] 1 solder lug with center tap sensing.honeywell.com 19 485 Series Specific Configurations Table 7. 485 Series Specific Configurations (continued) Shaft Type Bushing AR Type Pin Termination 485-I (See Table 485-I on p. 26.) standard, 6,35 mm [0.250 in] slotted and 9,53 mm [0.375 in] 1 solder lug 485-K (See Table 485-K on p. 27.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 485-M (See Table 485-M on p. 28.) slotted standard, 7,9 mm [0.312 in] 1 solder lug 485-O (See Table 485-O on p. 29.) slotted 20 standard, 12,7 mm [0.500 in] 1 sensing.honeywell.com solder lug Configuration with Associated Hardware Shaft Type Bushing Type AR TerminPin ation 485-J (See Table 485-J on p. 26.) slotted standard, 8,69 mm [0.342 in] 0 solder lug 485-L (See Table 485-L on p. 27.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 485-N (See Table 485-N on p. 28.) standard, 9,53 mm [0.375 in] slotted and 12,7 mm [0.500 in] 1 solder lug 485-P (See Table 485-P on p. 29.) slotted standard, 9,53 mm [0.375 in] 1 solder lug Configuration with Associated Hardware 485 Series Specific Configurations Table 7. 485 Series Specific Configurations (continued) Shaft Type Bushing AR Type Pin Termination 485-Q (See Table 485-Q on p. 30.) standard, slotted 9,53 mm [0.375 in] 1 solder lug with center tap 485-S (See Table 485-S on p. 31.) standard, slotted 12,7 mm [0.500 in] 1 solder lug Configuration with Associated Hardware Shaft Type Bushing Type AR TerminPin ation Configuration with Associated Hardware 485-R (See Table 485-R on p. 30.) round standard, 9,53 mm [0.375 in] 1 solder lug 485-T (See Table 485-T on p. 31) standard, straight 8,67 mm knurled [0.342 in] 1 solder lug sensing.honeywell.com 21 485 Series Order Guides Table 485-A Order Guide 11,13 [0.438] 5,54 [0.218] 22,23 [0.875] 9,53 [0.375] RoHS Compliant D Bushing Length (mm [in]) no C Shaft Length (mm [in]) 1-4 12 [7-28] [1-4] B Flat Thickness (mm [in]) 312 A Flat Length (mm [in]) S-7 Operating Torque (mN m [in-oz]) 312 Shaft Seal 112 Stop Torque (N m [in-lb]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 5k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 485000M8990 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C D A 3,18 [0.125] Locating pin 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] B 12,87 [0.546] ø6,35 [0.250] Mounting surface 0,635 [0.025] 22,23 Max. [0.875] 90° 3/8-32 NEF-2A 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-B Order Guide 12 no 11,13 [0.438] 5,54 [0.218] 22,23 [0.875] 9,53 [0.375] RoHS Compliant S-14 D Bushing Length (mm [in]) 312 C Shaft Length (mm [in]) S-9 B Flat Thickness (mm [in]) Shaft Seal 312 A Flat Length (mm [in]) Stop Torque (N m [in-lb]) 112 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 10 k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 485025M9052 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] D A 22,23 Max. [0.875] 3,18 [0.125] 4X 1,57 [0.062] 4X 2,36 [0.093] 4X 3,15 [0.124] 4X 1,57 [0.062] 22 sensing.honeywell.com 2X 20° Terminal base 12,87 [0.546] ø6,35 Locating pin B [0.250] 3/8-32 NEF-2A 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 485 Series Order Guides Table 485-C Order Guide Dimensions Mechanical RoHS Compliant 485025M8843 10 k 10 4 4 112 312 S-13 312 1-4 [7-28] 12 [1.4] no 15,88 [0.625] 6,35 [0.250] yes unassembled 485025M9267 5k 10 4 4 112 312 S-13 312 1-4 [7-28] 12 [1.4] no 15,88 [0.625] 6,35 [0.250] yes unassembled Taper Mechanical Rotation (Degree) Mounting Hardware Catalog Listing End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Shaft Seal Bushing Length (mm [in]) Stop Torque (N m [in-lb]) Shaft Length (mm [in]) Operating Torque (mN m [in-oz]) B Resistance Tolerance (±%) A Resistance (Ohm) Electrical Rotation, ±3 (Degree) Electrical Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] A B 2,77 [0.109] 22,23 Max. [0.875] 3,18 [0.125] 4X 1,57 [0.062] 4X 2,36 [0.093] 4X 3,15 [0.124] Terminal base 12,87 [0.546] ø6,35 [0.250] Locating pin 22,23 Max. [0.875] 3/8-32 NEF-2A 0,635 [0.025] 1 Left Mounting surface 3,18 Min. [0.125] 4X 1,57 [0.062] 3 2 Right Center 2X 20° Table 485-D Order Guide 312 1-6 [7-42] Shaft Seal S-4 Stop Torque (N m [in-lb]) 312 12 yes [1.4] A B Shaft Length (mm [in]) Bushing Length (mm [in]) 22,23 [0.875] 9,53 [0.375] RoHS Compliant 284 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 5k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 485008M7167 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] Shown with 50% shaft rotation A ø27,79 Max. [1.094] 13,49 [0.531] B 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] Terminal base 12,87 [0.546] ø6,32 Locating pin [0.249] 22,23 Max. [0.875] 3/8-32 NEF-2A 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 1 Left 3 2 Right Center 2X 20° sensing.honeywell.com 23 485 Series Order Guides Table 485-E Order Guide Mechanical Rotation (Degree) 312 S-16 312 1-4 [7-28] 12 [1.4] no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 50,8 [2.000] 9,53 [0.375] RoHS Compliant 284 Shaft Seal 4 Stop Torque (N m [in-lb]) 4 Taper Electrical Rotation, ±3 (Degree) 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 5k Dimensions Mechanical Operating Torque (mN m [in-oz]) 485000M8930 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] Shown with 50% shaft rotation A ø27,79 Max. B [1.094] 13,49 [0.531] 3,18 [0.125] 3X 1,57 [0.062] 3X 1,57 [0.062] ø6,35 12,87 [0.546] [0.25] Locating pin 3X 2,36 [0.093] 3X 3,15 [0.124] 22,23 Max. [0.875] 3/8-32 NEF-2A Terminal base 2X 20° Mounting surface 0,635 [0.025] 3 2 Right Center 1 Left 3,18 Min. [0.125] Table 485-F Order Guide Mechanical Rotation (Degree) Taper 312 S-11 312 1-4 [7-28] 12 [1.4] no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 31,75 [1.250] 9,53 [0.375] RoHS Compliant 284 Shaft Seal 100 Stop Torque (N m [in-lb]) 4 Electrical Rotation, ±3 (Degree) 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 10 k Dimensions Mechanical Operating Torque (mN m [in-oz]) 485000M9156 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. [1.094] 13,49 [0.531] A B 2,77 [0.109] 3,18 [0.125] 3X 1,57 [0.062] 3X 1,57 [0.062] 24 sensing.honeywell.com [0.250] 0,635 [0.025] 2X 20° 22,23 Max. [0.875] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø6,35 Locating pin Mounting surface 3,18 Min. [0.125] 1 Left 3 2 Right Center 485 Series Order Guides Table 485-G Order Guide Shaft Seal 348 S-6 360 1-4 [7-28] - no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 76,2 [3.000] 9,53 [0.375] RoHS Compliant Stop Torque (N m [in-lb]) 180 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 25 k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 485004M8986 Resistance Tolerance (±%) 8.5 Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] A B 2,77 [0.109] ø1,58 [0.062] 2,39 [0.094] 3X 1,57 [0.062] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] Locating pin ø6,32 [0.249] Mounting surface 0,635 [0.025] 12,87 [0.546] 3,18 [0.125] 22,23 Max. [0.875] 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-H Order Guide Dimensions Mechanical Operating Torque (mN m [in-oz]) Stop Torque (N m [in-lb]) Shaft Seal Slot Length (mm [in]) Slot Width (mm [in]) Shaft Length (mm [in]) Bushing Length (mm [in]) RoHS Compliant Mounting Hardware 485025M9428 10 k 10 4 4 263 312 S-8 312 1-6 [7-42] 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 22,23 [0.875] 9,53 [0.375] yes unassembled 485042M9576 1k 10 4 4 263 312 S-8 312 1-6 [7-42] 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 22,23 [0.875] 9,53 [0.375] yes unassembled Catalog Listing End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Mechanical Rotation (Degree) D Taper C Electrical Rotation, ±3 (Degree) B Resistance Tolerance (±%) A Resistance (Ohm) Electrical Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] D A 22,23 Max. [0.875] 3,18 [0.125] 3X 1,57 [0.062] 4X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin Terminal base 4X 2,36 [0.093] 4X 3,15 [0.124] B [0.250] 3/8-32 NEF-2A 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 2X 20° sensing.honeywell.com 25 485 Series Order Guides Table 485-I Order Guide 485000M9564 50 k 10 4 4 284 312 S-9 312 485000M9641 10 k 10 4 4 284 312 S-9 312 485000M9708 1k 10 4 4 284 312 S-9 312 1-4 [1-28] 1-4 [1-28] 1-4 [1-28] 1-4 [1-28] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] no no no no 1,60 [0.063] 1,60 [0.063] 1,60 [0.063] 1,60 [0.063] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 15,88 [0.625] 9,53 [0.375] 9,53 [0.75] 9,53 [0.375] 6,35 [0.250] Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Mounting Hardware yes unassembled yes unassembled yes unassembled yes unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] RoHS Compliant 312 D Bushing Length (mm [in]) S-9 C Shaft Length (mm [in]) 312 B Depth Width (mm [in]) 284 A Slot Length (mm [in]) 4 Shaft Seal Mechanical Rotation (Degree) 4 Stop Torque (N m [in-lb]) Taper 10 Operating Torque (mN m [in-oz]) Electrical Rotation, ±3 (Degree) 5k End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Resistance Tolerance (±%) 485000M8723 Catalog Listing Dimensions Mechanical Resistance (Ohm) Electrical A 3,18 [0.125] 3X 1,57 [0.062] [0.250] 1 Left Mounting surface 0,635 [0.025] 22,23 Max. [0.875] 90° 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø6,35 Locating pin 3X 1,57 [0.062] 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-J Order Guide 12 [1.4] no Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] 1,60 [0.063] 1,19 [0.047] 50,8 [2.000] 9,53 [0.375] RoHS Compliant 1-4 [1-28] Bushing Length (mm [in]) 312 D Shaft Length (mm [in]) S-4 C Slot Width (mm [in]) Shaft Seal 312 B Slot Depth (mm [in]) Stop Torque (N m [in-lb]) 284 Operating Torque (mN m [in-oz]) 10 Mechanical Rotation (Degree) 10 A Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 1M Dimensions Mechanical Electrical Rotation, ±3 (Degree) 485000M9017 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D A 3,18 [0.125] 12,87 [0.546] ø6,35 [0.250] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 26 sensing.honeywell.com 3/8-32 NEF-2A 2X 20° Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 Right 2 Center 485 Series Order Guides Table 485-K Order Guide Dimensional Drawings (For reference only: mm [in].) 1,19 [0.047] 22,23 [0.875] 9,53 [0.375] RoHS Compliant 12 1,60 yes [1.4] [0.063] Bushing Length (mm [in]) 1-6 [7-42] B Slot Depth (mm [in]) 312 Shaft Seal S-7 Stop Torque (N m [in-lb]) 311 D Shaft Length (mm [in]) 284 C Slot Width (mm [in]) 100 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 10 Taper 10 k A Electrical Rotation, ±3 (Degree) Resistance Tolerance (±%) 485042M9668 Dimensions Mechanical End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] A 3,18 [0.125] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 [0.250] Locating pin 3/8-32 NEF-2A 22,23 Max. [0.875] 90° Mounting surface 0,635 [0.025] 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-L Order Guide 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 22,23 [0.875] 9,53 [0.375] RoHS Compliant 1-4 [7-28] Bushing Length (mm [in]) 312 D Shaft Length (mm [in]) S-2 C Slot Width (mm [in]) Shaft Seal 312 B Slot Depth (mm [in]) Stop Torque (N m [in-lb]) 304 Operating Torque (mN m [in-oz]) 10 Mechanical Rotation (Degree) 10 A Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 1M Dimensions Mechanical Electrical Rotation, ±3 (Degree) 485000M8911 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] A ø6,35 [0.250] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] 3/8-32 NEF-2A Locating pin Terminal base 3,18 [0.125] Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 2X 20° sensing.honeywell.com 27 485 Series Order Guides Table 485-M Order Guide 12 [1.4] no Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 1,60 [0.063] 1,19 [0.047] 27,19 [1.031] 7,92 [0.312] RoHS Compliant 1-4 [7-28] Bushing Length (mm [in]) 312 D Shaft Length (mm [in]) S-9 C Slot Width (mm [in]) Shaft Seal 312 B Slot Depth (mm [in]) Stop Torque (N m [in-lb]) 33 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 A Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 5k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 485010M6860 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Shown with 50% shaft rotation C ø27,79 Max. D 2,77 [0.109] [1.094] 13,49 [0.531] A B 3,18 [0.125] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 [0.250] Locating pin 22,23 Max. [0.875] 90° 3/8-32 NEF-2A Mounting surface 0,635 [0.025] 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-N Order Guide 4 45 312 S-10 312 485008M8967 5k 10 4 4 45 312 S-10 312 485008M9458 5k 10 4 4 45 312 S-10 312 485008M9687 5k 10 4 4 45 312 S-10 312 485008M9688 5k 10 4 4 45 312 Dimensional Drawings (For reference only: mm [in].) S-A 312 14,30 [0.563] 20,62 [0.182] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 47,63 [1.875] 39,88 [1.570] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 9,53 [0.375] 9,53 [0.375] 12,7 [0.500] Mounting Hardware yes unassembled no unassembled yes unassembled yes unassembled yes unassembled yes unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] RoHS Compliant 4 D Bushing Length (mm [in]) 10 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] C Shaft Length (mm [in]) 5k 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] B Slot Width (mm [in]) 485008M0002 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] Slot Depth (mm [in]) 312 S-10 312 Shaft Seal 45 Stop Torque (N m [in-lb]) 4 A Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 10 Taper Resistance Tolerance (±%) 5k End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Resistance (Ohm) 485000M8990 Catalog Listing Dimensions Mechanical Electrical Rotation, ±3 (Degree) Electrical A 3,18 [0.125] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 28 sensing.honeywell.com 2X 20° 12,87 [0.546] ø6,35 Locating pin [0.250] 22,23 Max. [0.875] 3/8-32 NEF-2A 90° 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 1 Left 3 2 Right Center 485 Series Order Guides Table 485-O Order Guide Slot Depth (mm [in]) Shaft Seal Stop Torque (N m [in-lb]) Operating Torque (mN m [in-oz]) Taper Mechanical Rotation (Degree) 1-6 [7-42] 312 S-10 312 12 1,60 yes [1.4] [0.063] Dimensional Drawings (For reference only: mm [in].) C D 1,19 [0.047] 25,4 [1.000] 12,7 [0.500] RoHS Compliant 45 B Bushing Length (mm [in]) 4 A Shaft Length (mm [in]) 4 Electrical Rotation, ±3 (Degree) 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 5k Dimensions Mechanical Slot Width (mm [in]) 485008M0004 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware no unassembled Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] A 3,18 [0.125] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin [0.250] 3/8-32 NEF-2A Mounting surface 0,635 [0.025] 22,23 Max. [0.875] 90° 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-P Order Guide 1,60 [0.063] 1,19 [0.047] 50,8 [2.000] 9,53 [0.375] RoHS Compliant no Bushing Length (mm [in]) 12 [1.4] D Shaft Length (mm [in]) 1-4 [7-28] C Slot Width (mm [in]) Mechanical Rotation (Degree) Taper 312 S-10 312 B Slot Depth (mm [in]) 46 Shaft Seal 4 A Stop Torque (N m [in-lb]) 4 Electrical Rotation, ±3 (Degree) 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 20 k Dimensions Mechanical Operating Torque (mN m [in-oz]) 485000M9651 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] A 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] Terminal base 12,87 [0.546] ø6,35 Locating pin [0.250] 3/8-32 NEF-2A 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 2X 20° sensing.honeywell.com 29 485 Series Order Guides Table 485-Q Order Guide 1,60 [0.063] 1,19 [0.047] 50,8 [2.000] 9,53 [0.375] RoHS Compliant no Bushing Length (mm [in]) - D Shaft Length (mm [in]) 1-4 C Slot Width (mm [in]) Mechanical Rotation (Degree) Taper 348 S-12 360 B Slot Depth (mm [in]) 270 Shaft Seal 4 A Stop Torque (N m [in-lb]) 4 Electrical Rotation, ±3 (Degree) 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 10 k Dimensions Mechanical Operating Torque (mN m [in-oz]) 485030M9652 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. [1.094] 13,49 [0.531] C D 2,77 [0.109] A B 22,56 Max. [0.888] 3,18 [0.125] 4X 1,57 [0.062] Terminal base 4X 2,36 [0.093] 4X 3,15 [0.124] 4X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin [0.250] 3/8-32 NEF-2A 0,635 [0.025] 22,23 Max. [0.875] 90° Mounting surface 3 2 Right Center 1 Left 3,18 Min. [0.125] 2X 20° Table 485-R Series Order Guide Shaft Seal 312 S-5 312 1-4 12 no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 63,5 [2.500] 9,53 [0.375] RoHS Compliant Stop Torque (N m [in-lb]) 250 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 1k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 485040M9512 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] D Shown with 50% shaft rotation ø27,79 Max. C ø2,36 2,77 [0.109] [1.094] 13,49 [0.531] 49,40 [1.945] [0.093] 5,70 [0.226] 3,18 [0.125] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 30 sensing.honeywell.com Locating pin 2X 20° 3/8-32 NEF-2A Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 12,7 [0.125] 12,7 [0.125] 12,87 [0.546] 22,23 Max. [0.875] ø6,35 [0.250] 1 Left 3 2 Right Center 485 Series Order Guides Table 485-S Order Guide 0,23 [0.009] 1,19 [0.047] 25,15 [0.990] 12,7 [0.500] RoHS Compliant yes Bushing Length (mm [in]) 12 D Shaft Length (mm [in]) 1-6 C Slot Width (mm [in]) Mechanical Rotation (Degree) Taper 312 S-15 312 B Slot Depth (mm [in]) 45 Shaft Seal 4 A Stop Torque (N m [in-lb]) 4 Electrical Rotation, ±3 (Degree) 5 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 5k Dimensions Mechanical Operating Torque (mN m [in-oz]) 485048M9728 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware no unassembled Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. C [1.094] 13,49 [0.531] D 2,77 [0.109] A 7,32 [0.288] B 3,18 [0.125] 5,64 [0.222] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin [0.250] 3/8-32 NEF-2A 22,23 Max. [0.875] 90° Mounting surface 0,635 [0.025] 3 1 2 Left Center Right 3,18 Min. [0.125] 2X 20° Table 485-T Order Guide 348 Mechanical Rotation (Degree) Taper S-8 360 1-4 - no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 19,05 [0.750] 8,69 [0.342] RoHS Compliant 158 Shaft Seal 4 Stop Torque (N m [in-lb]) 4 Electrical Rotation, ±3 (Degree) 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 20 k Dimensions Mechanical Operating Torque (mN m [in-oz]) 485022M8995 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. A [1.094] 13,49 [0.531] B 2,77 [0.109] ø6,35 [0.250] 3X 1,57 [0.062] 3X 1,57 [0.062] 12,87 [0.546] Locating pin Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3,18 [0.125] 22,23 Max. [0.875] 3/8-32 NEF-2A Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 1 Left 3 2 Right Center 2X 20° sensing.honeywell.com 31 53C Series Specific Configurations Table 8. 53C Series Specific Configurations Shaft Type Bushing AR Type Pin Termination 53C1 (See Table 53C1 on pp. 33-34.) round standard, 9,53 mm [0.375 in] 1 solder lug 53C3 (See Table 53C3 on pp. 36-37.) slotted 32 standard, 6,35 mm [0.25 in] 1 sensing.honeywell.com solder lug Configuration with Associated Hardware Shaft Type Bushing Type AR TerminPin ation 53C2 (See Table 53C2 on p. 35.) slotted high torque, 12,7 mm [0.500 in] 1 solder lug Configuration with Associated Hardware 53C Series Order Guides Table 53C1 Order Guide Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) 274 312 S-4 312 53C1100K 100 k 10 4 4 274 312 S-4 312 53C110K 10 k 10 4 4 274 312 S-4 312 53C110MEG 10 M 20 10 10 274 312 S-4 312 53C11500 1.5 k 10 4 4 274 312 S-4 312 53C115K 15 k 10 4 4 274 312 S-4 312 53C11K 1k 10 4 4 274 312 S-4 312 53C11MEG 1M 20 10 10 274 312 S-4 312 53C120k 20 k 10 4 4 274 312 S-4 312 53C1250 250 10 4 4 274 312 S-4 312 53C12500 2.5 k 10 4 4 274 312 S-4 312 53C1250K 250 k 10 10 10 274 312 S-4 312 53C125K 25 k 10 4 4 274 312 S-4 312 53C12K 2k 10 4 4 274 312 S-4 312 53C135k 35 k 10 4 4 274 312 S-4 312 53C150 50 k 10 4 4 274 312 S-4 312 53C1500 500 10 4 4 274 312 S-4 312 53C1500k 500 k 10 10 10 274 312 S-4 312 53C150k 50 k 10 4 4 274 312 S-4 312 53C15K 5k 10 4 4 274 312 S-4 312 53C15meg 5M 20 10 10 274 312 S-4 312 53c1sw100k 100 k 10 4 4 274 312 S-4 312 53c1sw10k 10 k 10 4 4 274 312 S-4 312 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] no no no no no no no no no no no no no no no no no no no no no no no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] RoHS Compliant Effective Electrical Rotation, Typ. (Degree) 4 Shaft Seal End Resistance at CCW, Max. (Ohm) 4 Stop Torque (N m [in-lb]) End Resistance at CW, Max. (Ohm) 10 53C1100 Operating Torque (mN m [in-oz]) Resistance Tolerance (±%) 100 Catalog Listing Dimensions Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled (Continued on next page.) sensing.honeywell.com 33 53C Series Order Guide Table 53C1 Order Guide (continued) Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) 4 274 312 Z 312 53c110KZ 10 k 10 100 4 274 312 Z 312 53c11MEGZ 1M 20 10 k 10 274 312 Z 312 53c1250KZ 250 k 10 2.5 k 10 274 312 Z 312 53c125KZ 25 k 10 250 4 274 312 Z 312 53c1500KZ 500 k 10 5k 10 274 312 Z 312 53c150KZ 50 k 10 500 4 274 312 Z 312 53c15KZ 5k 10 50 4 274 312 Z 312 100 k 10 1k 4 274 312 RZ 312 53C1-100K-RZ 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] no no no no no no no no no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] RoHS Compliant Effective Electrical Rotation, Typ. (Degree) 1k Shaft Seal End Resistance at CCW, Max. (Ohm) 10 Stop Torque (N m [in-lb]) End Resistance at CW, Max. (Ohm) 100 k Operating Torque (mN m [in-oz]) Resistance Tolerance (±%) 53c1100KZ Catalog Listing Dimensions Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] A Shown with 50% shaft rotation B 2,77 [0.109] 3,18 [0.125] ø27,79 Max. [1.094] 13,49 [0.531] ø12,7 [0.500] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 34 Locating pin 3/8-32 NEF-2A Mounting surface Terminal base 0,64 [0.025] 2X 20° sensing.honeywell.com 12,87 [0.546] ø6,35 [0.250] 22,23 Max. [0.875] 1 Left 3,18 Min. [0.125] 3 2 Right Center 53C Series Order Guides Table 53C2 Order Guide End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) 4 274 312 S-4 312 53C2100K 100 k 10 4 4 274 312 S-4 312 53C210K 10 k 10 4 4 274 312 S-4 312 53C21500 1.5 k 10 4 4 274 312 S-4 312 53C2150K 150 k 10 4 4 274 312 S-4 312 53C215K 15 k 10 4 4 274 312 S-4 312 53C21K 1k 10 4 4 274 312 S-4 312 53C21MEG 1M 10 10 10 274 312 S-4 312 53C22.5MEG 2.5 M 20 10 10 274 312 S-4 312 53C220K 20 k 10 4 4 274 312 S-4 312 53C2250 250 10 4 4 274 312 S-4 312 53C22500 2.5 k 10 4 4 274 312 S-4 312 53C2250K 250 k 10 10 10 274 312 S-4 312 53C225K 25 k 10 4 4 274 312 S-4 312 53C22K 2k 10 4 4 274 312 S-4 312 53C22MEG 2M 20 10 10 274 312 S-4 312 3.5 M 20 10 10 274 312 S-4 312 53C250 50 10 4 4 274 312 S-4 312 53C2500 500 10 4 4 274 312 S-4 312 53C2500K 500 k 10 10 10 274 312 S-4 312 53C250K 50 k 10 4 4 274 312 S-4 312 53C25K 5k 10 4 4 274 312 S-4 312 53C25MEG 5M 20 10 10 274 312 S-4 312 53C23.5MEG Shaft Seal End Resistance at CW, Max. (Ohm) 4 Stop Torque (N m [in-lb]) Resistance Tolerance (±%) 10 53C2100 Operating Torque (mN m [in-oz]) Resistance (Ohm) 100 Catalog Listing Dimensions Mechanical 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] no no no no no no no no no no no no no no no no no no no no no no no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 15,88 [0.625] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] RoHS Compliant Electrical Mounting Hardware no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] A Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] 11,9 [0.047] B 1,6 [0.063] 3,18 [0.125] ø12,7 [0.500] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] ø6,35 [0.250] Locating pin 3/8-32 NEF-2A Terminal base Mounting surface 0,64 [0.025] 3,18 Min. [0.125] 12,87 [0.546] 22,23 Max. [0.875] 90° 3 1 Right 2 Left Center 2X 20° sensing.honeywell.com 35 53C Series Order Guide Table 53C3 Order Guide Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) Stop Torque (N m [in-lb]) Shaft Seal RoHS Compliant 100 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C3100K 100 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C310K 10 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C3150 150 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C31500 1.5 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C3150K 150 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C315K 15 k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4 no 22,23 [0.875] 9,53 [0.375] no unassembled 53C31K 1k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53c31k/new 1k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C31MEG 1M 10 10 10 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C32.5MEG 2.5 M 20 10 10 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C3200K 200 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53c320k 20 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C3250 250 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C32500 2.5 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C3250K 250 k 10 10 10 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C325K 25 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C32K 2k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53c32MEG 2M 20 10 10 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53c3350 350 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53c33500 3.5 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53c350 50 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53c3500 500 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53c3500k 500 k 10 10 10 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53c3500k/new 500 k 10 10 10 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53c350k 50 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C3100 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) Bushing Length (mm [in]) End Resistance at CCW, Max. (Ohm) Shaft Length (mm [in]) End Resistance at CW, Max. (Ohm) B Resistance Tolerance (±%) A Mounting Hardware Catalog Listing (Continued on next page.) 36 Dimensions Mechanical Resistance (Ohm) Electrical sensing.honeywell.com 53C Series Order Guide Table 53C3 Order Guide (continued) Dimensions Mechanical Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) Stop Torque (N m [in-lb]) Shaft Seal RoHS Compliant Mounting Hardware 53c35k 5k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C35MEG 5M 20 10 10 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C3750k 750 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled 53C375K 75 k 10 4 4 274 312 S-4 312 1-6 12 [7-42] [1.4] no 22,23 [0.875] 9,53 [0.375] no unassembled Catalog Listing Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) Bushing Length (mm [in]) End Resistance at CCW, Max. (Ohm) Shaft Length (mm [in]) End Resistance at CW, Max. (Ohm) B Resistance Tolerance (±%) A Resistance (Ohm) Electrical A Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B 2,77 [0.109] ø6,35 [0.250] Locating pin 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 3/8-32 NEF-2A Terminal base Mounting surface 0,64 [0.025] 12,87 [0.546] 22,23 Max. [0.875] 90° 1 Left 3,18 Min. [0.125] 3 Right 2 Center 2X 20° sensing.honeywell.com 37 385 Series Specific Configurations Table 9. 385 Series Specific Configurations Shaft Type Bushing AR Type Pin Termination 385-A (See Table 385-A on p. 40.) flatted standard, 9,53 mm [0.375 in] 1 solder lug 385-C (See Table 385-C on p. 41.) flatted standard, 1 9,53 mm and [0.375 in] 2 solder lug 385-E (See Table 385-E on p. 42.) slotted high torque, 12,7 mm [0.500 in] 1 solder lug 385-G (See Table 385-G on p. 43.) slotted 38 high torque, 12,7 mm [0.500 in] 1 sensing.honeywell.com solder lug Configuration with Associated Hardware Shaft Type Bushing Type AR TerminPin ation 385-B (See Table 385-B on p. 40.) round standard, 9,53 mm [0.375 in] 1 solder lug 385-D (See Table 385-D on p. 41.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 385-F (See Table 385-F on p. 42.) slotted high torque, 12,7 mm [0.500 in] 1 solder lug 385-H (See Table 385-H on p. 43.) standard, 9,53 mm slotted [0.375 in] 1 solder lug Configuration with Associated Hardware 385 Series Specific Configurations Table 9. 385 Series Specific Configurations (continued) Shaft Type Bushing AR Type Pin Termination 385-I (See Table 385-I on p. 44.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 385-K (See Table 385-K on p. 45.) slotted standard, 9,53 mm [0.375 in] 1 solder lug Configuration with Associated Hardware Shaft Type Bushing Type AR TerminPin ation Configuration with Associated Hardware 385-J (See Table 385-J on p. 45.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 385-L (See Table 385-L on p. 46.) slotted standard, 9,53 mm [0.375 in] 1 solder lug sensing.honeywell.com 39 385 Series Order Guides Table 385-A Order Guide 385000M9136 5k 10 4 4 274 312 S-4 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 1-4 [7-28] 1-4 [7-28] 12 [1.4] 12 [1.4] no no 12,27 [0.483] 9,53 [0.375] 5,53 [0.218] 3,96 [0.156] 22,23 [0.875] 22,23 [0.875] 9,53 [0.375] 9,53 [0.375] C RoHS Compliant 312 D Bushing Length (mm [in]) S-4 C Shaft Length (mm [in]) 312 B Flat Thickness (mm [in]) 274 A Flat Length (mm [in]) 4 Shaft Seal Mechanical Rotation (Degree) 4 Stop Torque (N m [in-lb]) Taper 10 Operating Torque (mN m [in-oz]) Electrical Rotation, ±3 (Degree) 10 k End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Resistance Tolerance (±%) 385000M5783 Catalog Listing Dimensions Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled yes unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] A 3,18 [0.125] ø6,35 Locating pin 3X 1,57 [0.062] 12,87 [0.546] [0.250] 22,23 Max. [0.875] 90° Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] B 3/8-32 NEF-2A 0,635 [0.025] 3 Right 2 Center 1 Left Mounting surface 3,18 Min. [0.125] 2X 20° Table 385-B Order Guide 385500M4863 1k 10 4 4 274 312 S-4 312 385500M5694 5k 10 4 4 274 312 S-4 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 12 [1.4] 12 [1.4] 12 [1.4] no no no C 5,53 [0.218] 5,53 [0.218] 5,53 [0.218] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] Mounting Hardware no unassembled no unassembled no unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] RoHS Compliant 312 D Bushing Length (mm [in]) S-4 C Shaft Length (mm [in]) 312 B Flat Thickness (mm [in]) 274 A Flat Length (mm [in]) 4 Shaft Seal Mechanical Rotation (Degree) 4 Stop Torque (N m [in-lb]) Taper 10 Operating Torque (mN m [in-oz]) Electrical Rotation, ±3 (Degree) 100 k End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Resistance Tolerance (±%) 385500M0012 Catalog Listing Dimensions Mechanical Resistance (Ohm) Electrical A 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 40 sensing.honeywell.com Locating pin B 3/8-32 NEF-2A Terminal base 0,635 [0.025] 2X 20° ø6,35 [0.250] Mounting surface 3,18 Min. [0.125] 12,87 [0.546] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 385 Series Order Guides Table 385-C Order Guide Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) 4 274 312 S-4 312 385000M9168 100 10 4 4 274 312 S-4 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 1-4 [7-28] 1-4 [7-28] 12 [1.4] 12 [1.4] no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 19,05 [0.750] 19,05 [0.750] 9,53 [0.375] 9,53 [0.375] no C RoHS Compliant Effective Electrical Rotation, Typ. (Degree) 4 Shaft Seal End Resistance at CCW, Max. (Ohm) 10 Stop Torque (N m [in-lb]) End Resistance at CW, Max. (Ohm) 150 Operating Torque (mN m [in-oz]) Resistance Tolerance (±%) 385000M8551 Catalog Listing Dimensions Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled yes unassembled Shown with 50% shaft rotation ø27,79 Max. D [1.094] 13,49 [0.531] 2,77 [0.109] 3,18 [0.125] 3X 1,57 [0.062] 3X 1,57 [0.062] 22,23 Max. [0.875] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø6,35 [0.250] Locating pin 0,635 [0.025] 1 Left Mounting surface 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 385-D Order Guide End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) Operating Torque (mN m [in-oz]) Stop Torque (N m [in-lb]) Shaft Seal 10 k 10 100 4 274 312 Z 312 1-4 [7-28] 12 [1.4] no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 25,4 [1.000] 9,53 [0.375] RoHS Compliant End Resistance at CW, Max. (Ohm) 385000M8659 Resistance Tolerance (±%) Catalog Listing Dimensions Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] C Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 [0.250] Locating pin 22,23 Max. [0.875] 3/8-32 NEF-2A Terminal base 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 1 Left 3 2 Right Center 2X 20° sensing.honeywell.com 41 385 Series Order Guides Table 385-E Order Guide 12 [1.4] no Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 1,60 [0.063] 1,19 [0.047] 15,88 [0.625] 12,7 [0.500] RoHS Compliant 1-4 [7-28] D Bushing Length (mm [in]) 312 C Shaft Length (mm [in]) S-4 B Slot Thickness (mm [in]) Shaft Seal 312 A Slot Length (mm [in]) Stop Torque (N m [in-lb]) 274 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 75 Dimensions Mechanical Electrical Rotation, ±3 (Degree) 385500M9303 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware yes unassembled Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] A B 3,18 [0.125] 3X 1,57 [0.062] 3X 1,57 [0.062] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø6,35 [0.250] Locating pin Mounting surface 0,635 [0.025] 22,23 Max. [0.875] 90° 1 Left 3,18 Min. [0.125] 3 Right 2 Center 2X 20° Table 385-F Order Guide 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 15,88 [0.625] 12,7 [0.500] RoHS Compliant 1-4 [7-28] D Bushing Length (mm [in]) 312 C Shaft Length (mm [in]) S-4 B Slot Thickness (mm [in]) Shaft Seal 312 A Slot Length (mm [in]) Stop Torque (N m [in-lb]) 274 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 200 Dimensions Mechanical Electrical Rotation, ±3 (Degree) 385500M1654 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware no unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] C D 2,77 [0.109] A Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 42 sensing.honeywell.com 3/8-32 NEF-2A Terminal base Mounting surface 0,635 [0.025] 2X 20° 12,87 [0.546] ø6,35 [0.250] Locating pin 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 385 Series Order Guides Table 385-G Order Guide D Bushing Length (mm [in]) 1,19 [0.047] 15,88 [0.625] 12,7 [0.500] 1-6 24 1,60 yes [7-42] [2.8] [0.063] Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Mounting Hardware no unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C D 2,77 [0.109] RoHS Compliant C Shaft Length (mm [in]) Shaft Seal 312 Stop Torque (N m [in-lb]) S-4 Operating Torque (mN m [in-oz]) 312 B Slot Thickness (mm [in]) 274 A Slot Length (mm [in]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 5k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 385518M0018 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical A 3,18 [0.125] 3X 1,57 [0.062] 3X 1,57 [0.062] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø6,35 [0.250] Locating pin Mounting surface 0,635 [0.025] 22,23Max. [0.875] 90° 3 2 Right Center 1 Left 3,18 Min. [0.125] 2X 20° Table 385-H Order Guide Dimensions Mechanical Operating Torque (mN m [in-oz]) Stop Torque (N m [in-lb]) Shaft Seal Slot Length (mm [in]) Slot Thickness (mm [in]) Shaft Length (mm [in]) Bushing Length (mm [in]) RoHS Compliant Mounting Hardware 385000M1495 5M 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 15,88 [0.625] 9,53 [0.375] yes unassembled 385000M6960 270 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 22,23 [0.875] 9,53 [0.375] yes unassembled Catalog Listing End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Mechanical Rotation (Degree) D Taper C Electrical Rotation, ±3 (Degree) B Resistance Tolerance (±%) A Resistance (Ohm) Electrical Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] A B 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 [0.250] Locating pin 3/8-32 NEF-2A Terminal base Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 Right 2 Center 2X 20° sensing.honeywell.com 43 385 Series Order Guides Table 385-I Order Guide 12 [1.4] no RoHS Compliant 1-4 [7-28] D Bushing Length (mm [in]) 312 C Shaft Length (mm [in]) S-4 B Slot Thickness (mm [in]) Shaft Seal 312 A Slot Length (mm [in]) Stop Torque (N m [in-lb]) 274 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 10 k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 385500M0297 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware 1,60 [0.063] 1,19 [0.047] 22,23 [0.875] 9,53 [0.375] no unassembled 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 22,23 [0.875] 9,53 [0.375] no unassembled 385500M0567 1k 10 4 4 274 312 S-4 312 1-4 [7-28] 385500M0563 1k 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 31,75 [1.25] 9,53 [0.375] no unassembled 385500M1231 200 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 22,23 [0.875] 9,53 [0.375] no unassembled 385500M1377 500 10 4 4 274 312 S-4 312 1-4 [7-28] 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 22,23 [0.875] 9,53 [0.375] no unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] A B 3,18 [0.125] Locating pin 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 44 sensing.honeywell.com [0.250] 3/8-32 NEF-2A Terminal base Mounting surface 0,635 [0.025] 2X 20° 12,87 [0.546] ø6,35 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 Right 2 Center 385 Series Order Guides Table 385-J Order Guide 385518M0869 2.5 k 10 4 4 274 312 S-4 312 385518M1309 2.5 k 10 4 4 274 312 S-4 312 385518M1813 10 k 10 4 4 274 312 S-4 312 385518M2059 50 k 10 4 4 274 312 S-4 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 12,7 [0.500] 22,23 [0.875] 12,7 [0.500] 22,23 [0.875] 12,7 [0.500] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] Mounting Hardware no unassembled no unassembled no unassembled no unassembled no unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] RoHS Compliant 312 D Bushing Length (mm [in]) S-4 C Shaft Length (mm [in]) 312 B Slot Thickness (mm [in]) 274 A Slot Length (mm [in]) 4 Shaft Seal Mechanical Rotation (Degree) 4 Stop Torque (N m [in-lb]) Taper 10 Operating Torque (mN m [in-oz]) Electrical Rotation, ±3 (Degree) 10 k End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Resistance Tolerance (±%) 385518M0106 Catalog Listing Dimensions Mechanical Resistance (Ohm) Electrical A 3,18 [0.125] 3X 1,57 [0.062] 3X 1,57 [0.062] [0.250] 22,23 Max. [0.875] 90° 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø6,35 Locating pin 1 Left Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 3 Right 2 Center 2X 20° Table 385-K Order Guide 385500M9553 1M 20 10 k 10 274 312 Z 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] 1-4 [7-28] 1-4 [7-28] 12 [1.4] 12 [1.4] no no 1,60 [0.063] 1,60 [0.063] 1,19 [0.047] 1,19 [0.047] 22,23 [0.875] 22,23 [0.875] 9,53 [0.375] 9,53 [0.375] RoHS Compliant 312 D Bushing Length (mm [in]) Z C Shaft Length (mm [in]) 312 B Slot Thickness (mm [in]) 274 A Slot Length (mm [in]) 4 Shaft Seal Mechanical Rotation (Degree) 4 Stop Torque (N m [in-lb]) Taper 10 Operating Torque (mN m [in-oz]) Electrical Rotation, ±3 (Degree) 100 k End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Resistance Tolerance (±%) 385000M8686 Catalog Listing Dimensions Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled yes unassembled Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] B D A 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin [0.250] 3/8-32 NEF-2A Terminal base 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 Right 2 Center 2X 20° sensing.honeywell.com 45 385 Series Order Guides Table 385-L Order Guide 12 [1.4] no 1,60 [0.063] 1,19 [0.047] 22,23 [0.875] 9,53 [0.375] RoHS Compliant 1-4 [7-28] D Bushing Length (mm [in]) 312 C Shaft Length (mm [in]) Z B Slot Thickness (mm [in]) Shaft Seal 312 A Slot Length (mm [in]) Stop Torque (N m [in-lb]) 274 Operating Torque (mN m [in-oz]) 10 Mechanical Rotation (Degree) 2.5 k Taper 10 End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) 250 k Dimensions Mechanical Electrical Rotation, ±3 (Degree) 385500M1246 Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware no unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] A 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 46 sensing.honeywell.com ø6,35 Locating pin 3/8-32 NEF-2A Terminal base 0,635 [0.025] 2X 20° 12,87 [0.546] [0.250] Mounting surface 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center ADDITIONAL INFORMATION The following associated literature is available at sensing.honeywell.com: • Product Range Guide • Product Line Guide • Installation Instructions WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. WARNING MISUSE OF DOCUMENTATION • • The information presented in this product sheet is for reference only. Do not use this document as a product installation guide. Complete installation, operation, and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in death or serious injury. WARRANTY/REMEDY Find out more Honeywell serves its customers through a worldwide network of sales offices, representatives and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact your local sales office. To learn more about Honeywell’s Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items it finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. While we provide application assistance personally, through our literature and the Honeywell website, it is up to the customer to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. sensing and control products, call +1-815-235-6847 or 1-800-537-6945, visit sensing.honeywell.com, or e-mail inquiries to [email protected] Sensing and Control Honeywell 1985 Douglas Drive North Golden Valley, MN 55422 honeywell.com 32301266-A-EN IL5O October 2014 © 2014 Honeywell International Inc. All rights reserved.