HCN / HEN / HSN - Jianghai Europe

HCN-HEN-HSN
CD 261 LK Series Series
2 000h, Standard 105°C
· Low ESR, high ripple current capability
· HEN / HSN enlarged ripple currents
HGN
HCS
longer life
HPF
higher voltage
125°C
longer
HCE
life
HCN / HEN / HSN
ultra
low ESR
HPN / HEL / HPNA
low ESL
Item
Characteristics
Category Temperature Range (°C)
-55 ~ +105
Rated Voltage Range (VDC)
2,5 ~ 35
Capacitance Range (µF)
10 ~ 2 700
Capacitance Tolerance
(at 20°C, 120Hz)
± 20% (M)
Surge Voltage
Rated Voltage(V) x 1,15
Dissipation Factor (tanδ)
Please see the attached ratings list
(at 20°C, 120Hz)
Leakage Current *1
Please see the attached ratings list
Rated voltage applied, after 2 minutes.
Equivalent Series Resistance (ESR)
Please see the attached ratings list
(at 20°C, 100kHz)
Temperature Characteristics
(Max. Impedance Ratio)
Z(+105°C) / Z(+20°C) ≤1,25
105°C, 2 000h
Rated voltage applied
Life Time
60°C, 90 to 95% RH
1 000h
No-applied voltage
Damp heat
(Steady state)
Resistance to soldering heat
(at 100kHz)
Z(- 55°C) / Z(+20°C) ≤1,25
Wave method
(260°C + / -5°C x 10s)
Δ C/C
≤ ± 20% of the initial value
DF (tanδ)
≤ 150% of the initial specified value
ESR
≤ 150% of the initial specified value
LC
≤ The initial specified value
Δ C/C
≤ ± 20% of the initial value
DF (tanδ)
≤ 150% of the initial specified value
ESR
≤ 150% of the initial specified value
LC
≤ The initial specified value (after voltage processing)
Δ C/C
≤ ± 5% of the initial value
DF (tanδ)
≤ The initial specified value
ESR
≤ The initial specified value
LC
≤ The initial specified value (after voltage processing)
*1 please see Handling Precautions and
Chapter 4.1 of IEC 60384-26 :2011
Screw
Radial
Multiplier for Ripple Current
v2014.1
Frequency Coefficient
Frequency ƒ
Coefficient
126
120Hz ≤ ƒ <1kHz
1kHz ≤ ƒ <10kHz
10kHz ≤ ƒ < 100kHz
100kHz ≤ ƒ ≤ 500kHz
0,05
0,3
0,7
1
Assistance needed? Please contact Jianghai Europe GmbH +49 (0) 2151 652088-72 or [email protected]
HCN-HEN-HSN
CD 261 LK Series
Ratings for HCN Series (order code CN), HEN (order code EN), HSN (order code SN)
Rated
ESR
Rated Dissipation Leakage
Capa- (max) Ripple
Factor
Current
UR
Size
citance
Current Tanδ (max) (max)
Code
Ø D x L Case Series
20°C,
20°C, 105°C,
20°C,
20°C,
Code Code
120Hz 100kHz 100kHz
120Hz
2 min
(μF)
(mΩ)
(mArms)
(%)
(μA)
(mm)
(mΩ)
(mArms)
(%)
(μA)
20
3 200
8
195
6,3 x 10 F10
CN
47
25
2900
8
95
6,3 x 10 F10
CN
10
5 230
12
340
8 x 11,5 BAB
CN
68
25
2900
8
136
6,3 x 10 F10
CN
7
5 700
8
340
8 x 11,5 BAB
EN
100
25
2900
8
200
6,3 x 10 F10
CN
5
6 630
12
340
8 x 11,5 BAB
SN
150
25
2900
8
300
6,3 x 10 F10
CN
10
5 230
12
410
8 x 11,5 BAB
CN
25
2900
12
440
6,3 x 10 F10
CN
7
6 100
8
410
8 x 11,5 BAB
EN
10
5500
12
330
10 x 12,5 CAC
CN
5
6 630
12
410
8 x 11,5 BAB
SN
14
4420
12
540
8 x 11,5 BAB
CN
7
6 100
8
500
8 x 11,5 BAB
EN
8
5650
8
540
8 x 11,5 BAB
EN
6
6 640
8
500
10 x 12,5 CAC
EN
330
14
4420
12
660
8 x 11,5 BAB
CN
8
5 500
12
600
10 x 12,5 CAC
CN
390
8
5650
8
780
8 x 11,5 BAB
EN
6
6 640
8
600
10 x 12,5 CAC
EN
8
5650
8
940
8 x 11,5 BAB
EN
7
6 100
8
750
8 x 11,5 BAB
EN
10
5500
12
705
10 x 12,5 CAC
CN
8
5 500
12
750
10 × 12,5 CAC
CN
7
6100
8
940
10 x 12,5 CAC
EN
7
6 100
8
750
10 x 12,5 CAC
EN
12
5300
12
840
10 x 12,5 CAC
CN
5
7 220
12
750
10 x 12,5 CAC
SN
7
6100
8
1 120
10 x 12,5 CAC
EN
2 700
7
6 100
8
1 350
10 x 12,5 CAC
EN
680
7
6100
8
1360
10 x 12,5 CAC
EN
270
20
3 200
8
220
6,3 x 10 F10
CN
1000
390
20
3 300
8
320
6,3 x 10 F10
CN
10
5 230
12
450
8 x 11,5 BAB
CN
7
6 100
8
450
8 x 11,5 BAB
EN
5
6 630
12
450
8 x 11,5 BAB
SN
7
6 100
8
550
8 x 11,5 BAB
EN
7
6 100
8
660
8 x 11,5 BAB
EN
8
5 500
12
660
10 x 12,5 CAC
CN
6
6 640
8
660
10 x 12,5 CAC
EN
5
7 220
12
660
10 x 12,5 CAC
SN
7
6 100
8
800
8 x 11,5 BAB
EN
8
5 500
12
800
10 x 12,5 CAC
CN
6
6 640
8
800
10 x 12,5 CAC
EN
10
5100
7
6 100
8
960
8 x 11,5 BAB
EN
10
5500
8
5 500
12
960
10 x 12,5 CAC
CN
14
5050
7
6 100
8
960
10 x 12,5 CAC
EN
10
6100
5
7 220
12
960
10 x 12,5 CAC
SN
470
10
7
6 100
8
1 440
10 x 12,5 CAC
EN
33
47
390
680
820
2,5
0E
1 000
1 200
1 500
560
680
820
4
0G
1 000
1 200
1 800
(μF)
220
270
10
1A
470
560
100
150
180
16
1C
220
270
330
(mm)
8
6100
8
2000
10 x 12,5 CAC
EN
24
2900
8
320
6,3 x 10 F10
CN
16
4360
12
320
8 x 11,5 BAB
CN
16
4000
12
480
8 x 8 B08
CN
16
4360
12
480
8 x 11,5 BAB
CN
10
5500
12
360
10 x 12,5 CAC
CN
16
4360
12
580
8 x 11,5 BAB
CN
11
5100
8
580
8 x 11,5 BAB
EN
16
4000
12
705
8 x 8 B08
CN
16
4360
12
705
8 x 11,5 BAB
CN
10
5100
8
865
8 x 11,5 BAB
EN
14
5050
12
650
10 x 12,5 CAC
CN
8
1060
8 x 11,5 BAB
EN
8
1060
10 x 9 C09
EN
12
795
10 x 12,5 CAC
CN
8
1060
10 x 12,5 CAC
EN
6100
8
1510
10 x 12,5 CAC
EN
48
2200
6
135
6,3 x 10 F10
CN
30
2800
12
190
8 x 8 B08
CN
24
3320
12
400
8 x 11,5 BAB
CN
20
4320
12
400
10 x 12,5 CAC
CN
2 200
7
6 100
8
1 760
10 x 12,5 CAC
EN
220
20
3 200
8
280
6,3 x 10 F10
CN
20
3 300
8
420
6,3 x 10 F10
CN
7
5 700
8
420
8 x 11,5 BAB
EN
150
20
4320
12
600
10 x 12,5 CAC
CN
12
4 770
12
500
8 x 11,5 BAB
CN
10
50
2000
12
50
6,3 x 8 F08
CN
330
390
470
560
6,3
0J
(V)
680
820
1000
1500
20
1D
100
7
5700
8
495
8 x 11,5 BAB
EN
15
48
2200
6
75
6,3 x 10 F10
CN
5
6 630
12
495
8 x 11,5 BAB
SN
22
30
2800
12
110
8 x 8 B08
CN
12
4 770
12
595
8 x 11,5 BAB
CN
33
24
3600
12
165
8 x 11,5 BAB
CN
7
5 700
8
595
8 x 11,5 BAB
EN
47
24
3320
12
235
8 x 11,5 BAB
CN
7
5 700
8
710
8 x 11,5 BAB
EN
56
20
3800
12
280
10 x 12,5 CAC
CN
7
5 700
8
860
8 x 11,5 BAB
EN
68
24
3320
12
340
8 x 11,5 BAB
CN
10
5 500
12
645
10 x 12,5 CAC
CN
100
20
4320
12
500
10 x 12,5 CAC
CN
7
6 640
8
860
10 x 12,5 CAC
EN
10
50
2300
12
175
8 x 8 B08
CN
5
7 220
12
860
10 x 12,5 CAC
SN
18
34
2830
12
315
8 x 11,5 BAB
CN
7
5700
8
1 040
8 x 11,5 BAB
EN
33
30
3270
12
580
10 x 12,5 CAC
CN
10
5 500
12
775
10 x 12,5 CAC
CN
7
6 640
8
1 035
10 x 12,5 CAC
EN
5
7 220
12
1 035
10 x 12,5 CAC
SN
7
5 700
8
1 260
8 x 11,5 BAB
EN
10
5 500
12
950
10 x 12,5 CAC
CN
7
6 100
8
1 260
10 x 12,5 CAC
EN
10
5 560
8
1 890
10 x 12,5 CAC
EN
25
1E 35
1V
Radial
(V)
Rated
ESR
Rated Dissipation Leakage
Capa- (max) Ripple
Factor
Current
UR
Size
citance
Current Tanδ (max) (max)
Code
Ø D x L Case Series
20°C,
20°C, 105°C,
20°C,
20°C,
Code Code
120Hz 100kHz 100kHz
120Hz
2 min
Customer products are available on request.
Assistance needed? Please contact Jianghai Europe GmbH +49 (0) 2151 652088-72 or [email protected]
127
v2014.1
CD 261
Part
Number
LK Series
System
Part Number System Polymer Capacitors
PC
R
1V
Technology
Terminal
Type
Rated
Voltage Code
PC = Polymer
Capacitor
SMD = V
Radial = R
2,0V
2,5V
4V
6,3V
6,8V
7,0V
7,5V
10V
12,0V
12,5V
16V
= 0D
= 0E
= 0G
= 0J
= 06
= 07
= 75
= 1A
= A1
= 1B
= 1C
20V = 1D
Polymer
Screw
25V
28V
32V
35V
40V
50V
63V
80V
100V
125V
160V
180V
200V
= 1E
= L1
= 1F
= 1V
= 1G
= 1H
= 1J
= 1K
= 2A
= 2B
= 2C
= 2K
= 2D
VG
101
M
CAC
Series Code
Capacitance Code
(in µF)
Capacitance
Tolerance
Size Code
(øD x L)
SMD:
HVC
HVF
HVG
HVS
HVX
= VC
= VF
= VG
= SV
= VX
0,1
0,47
1,0
2,2
47
100
1 000
Radial:
HCN = CN
HCE
= CE
HEN = EN
= 0R1
= R47
= 010
= 2R2
= 470
= 101
= 102
±20%
±10%
+30 / -10%
+20 / -0%
±15%
+20 / -10%
=M
=K
=Q
=R
=L
=V
SMD:
D55
D60
E55
E60
F50
F55
F60
B70
B10
B11
HPN
= HN
B12
HPNA
HGN
HEL
HSN
HCS
HPF
= NA
= GN
= EL
= SN
= CS
= PF
C80
C10
C12
4,0
4,0
5,0
5,0
6,3
6,3
6,3
8,0
8,0
8,0
LL
50
Lead Form
x
x
x
x
x
x
x
x
x
x
5,2
5,7
5,2
5,7
5,0
5,2
5,7
6,7
9,7
11,0
Pitch
SMD:
Taped
= FV
Radial:
Taped
Long Lead
Cut 5,0mm
Cut4,5mm
Cut 4,0mm
Cut 3,5mm
Cut 3,0mm
= FF
= LL
= CB
= CC
= CD
= CE
= CF
SMD:
Standard
Radial:
2,0mm
2,5mm
3,5mm
5,0mm
P
E3
JE xxxxx
Material Code
for internal
use
for Specials
only
SMD:
W = Laminated
P = Plastic
-
= 20
= 25
= 35
= 50
Radial:
- = Standard
F = Flat Rubber
S = Stand-Off
8,0 x 12,2 on request: alternative lead forms
10 x
7,7
10 x
9,7
10 x 12,2
Radial:
D05
D07
E05
E07
F05
F06
F07
F08
F09
F10
B05
B06
4,0
4,0
5,0
5,0
6,3
6,3
6,3
6,3
6,3
6,3
8,0
8,0
x 5,7
x
7,0
x 5,7
x
7,0
x 5,7
x 6,7
x
7,0
x 8,0
x 9,0
x 10,0
x 5,7
x 6,7
B07
B08
B09
B10
B11
BAB
B12
BAC
B13
C08
C09
C10
C11
CAB
C12
CAC
C13
8,0
8,0
8,0
8,0
8,0
8,0
8,0
8,0
8,0
10
10
10
10
10
10
10
10
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
(Keyed polarity, axial, 90°-bended, other)
7,0
8,0
9,0
10,0
11,0
11,5
12,0
12,5
13,0
8,0
9,0
10,0
11,0
11,5
12,0
12,5
13,0
Technical Specification Radial Type Polymer
Dimensions for loose, long-lead type (bulk)
Order Code: LL
L
L<7
L≥7
ØD
5
6,3
8
5
6,3
8
10
F
2,0
2,5
3,5
2,0
2,5
3,5
5,0
Ød
0,45
aMax
1,0
0,5
0,6
2,0
in mm
Dimensions for loose, cut leads
Straight Lead
Code
CB
CC
CD
CE
CF
I
5,0 ± 0,5
4,5 ± 0,5
4,0 ± 0,5
3,5 ± 0,5
3,0 ± 0,5
preferred
v2014.1
114
Assistance needed? Please contact Jianghai Europe GmbH +49 (0) 2151 652088-72 or [email protected]
in mm
Part
CDNumber
261 LKSystem
Series
Dimension for Ammopack Taping
ΦD
A
P
P0
P1
P2
F
F1
W
W0
W1
W2
H
L
ΦD0
t
± 0,5
± 1,0
± 1,0
± 0,2
± 0,5
± 1,0
±1,0
±0,5
min
±0,5
max
±0,5
±0,3
5
7
8
9
10
5
8
10
11,5
6
6,7
8
11,5
7
9
10
12,5
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
12,7
5,35
5,35
5,35
5,35
5,35
5,1
5,1
5,1
5,1
4,6
4,6
4,6
4,6
3,85
3,85
3,85
3,85
6,35
6,35
6,35
6,35
6,35
6,35
6,35
6,35
6,35
6,35
6,35
6,35
6,35
6,35
6,35
6,35
6,35
3,5
3,5
3,5
3,5
3,5
3,5
3,5
3,5
3,5
3,5
3,5
3,5
3,5
5,0
5,0
5,0
5,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
18,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
12,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
9,0
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
0,75/
-0,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
18,5
max
5
5
5
5
5
6,3
6,3
6,3
6,3
8
8
8
8
10
10
10
10
0,8/
-0,2
2,0
2,0
2,0
2,0
2,0
2,5
2,5
2,5
2,5
3,5
3,5
3,5
3,5
5,0
5,0
5,0
5,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
11,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
4,0
0,7
0,7
0,7
0,7
0,7
0,7
0,7
0,7
0,7
0,7
0,7
0,7
0,7
0,7
0,7
0,7
0,7
Φ 5 x 5
Φ 5 x 7
Φ 5 x 8
Φ 5 x 9
Φ 5 x 10
Φ 6,3 x 5
Φ 6,3 x 8
Φ 6,3 x 10
Φ 6,3 x 11,5
Φ 8 x 6
Φ 8 x 6,7
Φ 8 x 8
Φ 8 x 11,5
Φ 10 x 7
Φ 10 x 9
Φ 10 x 10
Φ 10 x 12,5
in mm
Dimension for SMD Type and Dimensions for Taping
Dimension
Case Code
E = 1,75 ± 0,1 mm
T = 0,4 ± 0,1 mm
A
B
W
F
P
K
±0,2
±0,2
±0,3
±0,1
±0,1
±0,2
F60
7,0
7,0
16,0
7,5
12,0
6,3
F80
7,0
7,0
16,0
7,5
12,0
8,2
F10
7,0
7,0
24,0
11,5
16,0
10,2
B70
8,7
8,7
24,0
11,5
12,0
7,3
B80
8,7
8,7
24,0
11,5
12,0
8,3
B10
8,7
8,7
24,0
11,5
16,0
10,2
13,0
B12
8,7
8,7
24,0
11,5
16,0
C80
10,7
10,7
24,0
11,5
16,0
8,3
C10
10,7
10,7
24,0
11,5
16,0
11,0
C12
10,7
10,7
24,0
11,5
16,0
13,0
in mm
Recommended Soldering Pad
Case
Code
Quantity
(pcs/reel)
W1
(mm)
Φ D
(code)
a
b
c
Φ 6,3
(F)
1,9
3,5
1,6
Φ 8
(B)
3,1
4,2
2,2
Φ 10
(C)
4,5
4,4
2,2
F60
1 000
18
F80
900
18
F10
500
26
B70
1 000
26
B80
900
26
B10
500
26
B12
400
26
C80
500
26
C10
500
26
C12
400
26
Polymer
Real Dimensions
in mm
Recommended Soldering Profile SMD
Peak
230
tp
td
a
Temperature
217
tL
Preheat Area
ts
Time
a
Voltage
Range
(Vdc)
Preheat
2,5 ~ 16V
20 ~ 200V
Time maintained
above 217°C
Time maintained
above 230°C
Peak
Temperature
150~180°C
60~120 seconds
50 seconds max.
40 seconds max.
260°C max.
150~180°C
60~120 seconds
50 seconds max.
40 seconds max.
250°C max.
Only 1 reflow soldering cycle allowed. All temperatures are measured on the topside of the Al-can.
Assistance needed? Please contact Jianghai Europe GmbH +49 (0) 2151 652088-72 or [email protected]
115
v2014.1
Handling Precautions
Jianghai Electrolytic Capacitors
Warning: JIANGHAI is not responsible for any extent of possible damages to persons or things,
of any kind, caused by the improper application of and/or operating conditions harmful to electrolytic
capacitors.
Misapplications which may cause failures include, but are not limited to: * Ripple current or peak current
or voltage above specification, * Operating voltage above surge voltage specified, * Temperature exposure
beyond specified operating temperature range.
Examples of harmful operating conditions comprise, but are not limited to: * unusual storage or transport
temperatures, * excessive and/or rapid changes of ambient temperature or humidity, * heavy mechanical
shock or vibration, * corrosive and abrasive particles in the ambient (cooling) air, * conducting dust in the
ambient (cooling) air, * oil or water vapor or corrosive substances, * explosive gas or dust, * operation
under extremely high or low ambient pressure conditions (below or above sea level), * superimposed radio
frequency voltages, * radioactivity. In case of doubt about the impact of operating conditions on capacitor
performance, please contact JIANGHAI.
Personal Safety: Electrical or mechanical misapplication of electrolytic capacitors may be hazardous.
Personal injury or property damage may result from explosion of a capacitor or from the expulsion of
electrolyte due to mechanical disruption or the release of a safety vent of a capacitor.
In case of injury or skin or eye exposure to electrolyte, immediately seek professional medical advice.
Before using electrolytic capacitors in any application, please read these Handling Precautions,
familiarizing thoroughly with the information contained herein. Please check before using any of our
electrolytic capacitors if these components fulfill the requirements of your application and warnings and
instructions for use are followed.
Warranty: The information contained in this catalogue does not form part of any quotation or contract,
is believed to be accurate, reliable and up to date. Quality data are based on the statistical evaluations
of a large quantity of parts and do not constitute a guarantee in a legal sense. However, agreement on
these specifications does mean that the customer may claim for replacement of individual defective
capacitors within the terms of delivery. We will not assume any liability beyond the replacement of
defective components. This applies in particular to any consequential damage caused by component
failure. Furthermore it must be taken into consideration that the figures stated for lifetime, failure rates and
outlier percentages refer to the average production status and are therefore to be understood as mean
values (statistic expectations) for a large number of delivery lots of identical capacitors. These figures are
based on application experience and data obtained from preceding tests under normal conditions, or – for
purpose of accelerated aging – more severe conditions. JIANGHAI reserves the right to change these
specifications without prior notice. Any application information given is advisory and does not form part
of any specification. The products are not primarily designed for use in life support applications, devices
or systems where malfunction of these products can reasonably be expected to result in personal injury.
JIANGHAI customers using or selling these products for use in such applications without prior written
consent of JIANGHAI do so at their own risk and agree fully to indemnify JIANGHAI for any damage
resulting from such improper use or sale. This version of the catalogue supersedes all previous versions.
Latest versions of datasheets can be found on our homepage: www.jianghai-europe.com
For more details on precautions and guidelines for aluminum electrolytic capacitors, please refer to
CENELEC Technical Report CLC/TR 50454:2008 E, “Guide for the application of aluminum electrolytic
capacitors”.
Polarity: Electrolytic capacitors are polar and shall never be used with incorrect polarity, as there is a
possible danger of shorting or destruction.
Rated Voltage Ur: The Rated Voltage is marked on the capacitor and defined in the datasheets as Ur.
This voltage should never be exceeded and is the maximum peak voltage including any ripple voltages
allowed to avoid a shortening of the lifetime or damage of the capacitor. When a ripple current is applied
to the capacitor, the sum of the peak ripple voltage and bias DC voltage shall never exceed the Rated
Voltage. It might be necessary to lower the maximum allowed bias DC voltage, when certain ripple currents
are applied to the capacitor.
Surge Voltage: Maximum Voltage, which may be applied to the capacitor for short periods of time:
max. 1000 cycles of 30 sec. per 6 min., max. 5 pulses per hour. Capacitance drift +/- 15% max.
Reverse Voltage: Reverse voltages or voltages < 0 V are not allowed.
Recovery Voltage: After charging and discharging a capacitor there might still be a voltage between the
terminals, which is built up internally due to dielectric absorption. Please take action that this load does not
damage other devices or scare the workers during production (sparks possible).
Temperature Range: Use electrolytic capacitors only within the specified operating temperature range.
Over-Current: Currents exceeding the rated ripple currents should be avoided.
Ripple Current/Voltage: The combined value of DC voltage and peak AC voltage (due to ripple current)
shall not exceed the rated voltage and shall never be < 0 V. Use of aluminum electrolytic capacitors under
ripple current with wide amplitudes is equivalent to quick charge-discharge operation.
Rapid Charging/Discharging: Rapid Charging/Discharging generates severe heat and gas may be
emitted which may lead to explosion. Consult JIANGHAI about specially designed capacitors suitable for
such kind of applications. Example: Servo Drive Application
Balancing resistors: Balancing resistors should be utilized if capacitors are used in serial connection.
Please choose low-tolerance resistors to limit voltage drift.
Charge-Discharge Proof: JIANGHAI capacitors are charge-discharge proof, which means that 10 6
switching cycles will cause capacitance reduction of less than 10%.
Lifetime: There are many different lifetime definitions known without any true standard definition. Take
special care when capacitors are compared that the capacitors fulfill the needed requirements. JIANGHAI
publishes all conditions to be as transparent as possible. In the case of lifetime tests with additional ripple
currents, the bias DC voltage must be reduced, so that the sum of bias DC voltage and the peak of the
ripple voltage does not exceed the Rated Voltage Ur.
• Load Life: Period of time, during which the technical parameters of all capacitors stay within the given limits. JIANGHAI defines this without allowing for outliers.
• Useful Life: defined like load life, but a given percentage of components may be outside the defined limits. Useful life data are usually calculated within a confidence level of 60%. See further details in specifications and data sheets. Outlier percentage: ≤ 1%.
v2014.1
138
• Endurance Test: IEC 60384-4 defines the acceptable drift criteria of electrical parameters after the endurance tests (continuous voltage test).
• Shelf Life: Definition of time with acceptable drift of capacitor parameters after storage at upper category temperature without load. JIS-C-5102-1994
Vibration and mechanical stress: Capacitors are sensitive to vibration and mechanical forces applied
on the leads. Do not use capacitors, which have been dropped onto a rigid surface.
Insulation: If any defect of the sleeve is visible, the component should not be used – same for any kind
of visible damage. A capacitor should be electrically isolated from the following parts: Aluminum case,
cathode lead wire, anode lead wire and circuit pattern, and auxiliary terminal of snap-in type. The PVC
sleeve is not recognized as an isolator and therefore the standard capacitor should not be used in a place
where insulation function is needed. Please contact JIANGHAI if higher grade of insulation is required.
Environmental Conditions:
• Avoid direct contact with water, salt solution, oil, dewing conditions
• Halogens generally, especially fumigation treatment with bromides and flame retardent agents containing halogens must be avoided.
• Avoid exposing to direct sunshine, ozone, ultraviolet rays and x-ray radiation.
• Air Pressure: Max. 150kPa, min. 8kPa.
• No heavy air pressure changes are allowed.
• Do not use or store in an environment containing any hazardous gas (e.g., hydrogen sulphide, sulphurous acid, nitrous acid, chlorine, ammonia, bromine, methyl bromide, other halogens) or acidic or alkaline solutions.
Storage:
• Temperature 5 to 35°C, Relative Humidity below 75%.
• Electrolytic capacitors may accumulate charge naturally during storage. In this case discharge through a 1kOhm resistor before use (Recovery Voltage).
• Leakage current may be increased after long storage time. In this case the capacitor should be subjected to the rated voltage treatment through a 1kOhm resistor before use for 1 hour, then it should be discharged through a resistor of about 1 Ohm/Volt.
• Storage times above 1 year should be avoided or rated voltage treatment may be necessary.
• In accordance to IEC 60384-4 electrolytic capacitors are subject to a reforming process before acceptance testing. Rated voltage is applied via a series resistance (100Ω: Ur ≤ 100VDC,
1kΩ: Ur > 100VDC).
Soldering: Soldering conditions (temperature, times) should be within specified conditions, especially for
SMD components. Avoid high soldering temperatures as this may reduce lifetime or damage the capacitor.
Do never dip the capacitor body into molten solder. Flux should not be adhered to the capacitor’s body but
only to its terminals. For details and different methods please contact us.
Cleaning and Coating: Do not use fixing agents or cleaning substances containing halogens and the
epoxy resin coating materials. Also never use solvents containing: Halogenated hydrocarbons, alkali,
petroleum, trichloroethylene/-ethane, xylene, acetones, trichlorotrifluoroethane, tetrachloroethylene,
methylenechloride, chloroform, acetates, ketones, esters, chlorides and bromides. In case of questions
see detailed instructions.
Mounting: Other devices, which are mounted near the capacitor, should not touch the capacitor. Additional
heat coming from other components near the capacitor may reduce the lifetime of the capacitor. Do never
bend or twist the capacitor after soldering to avoid stress on the leads. Radial capacitors are not protected
against mechanical forces on the leads. Forces on the pins might damage the capacitor. No printed circuit
board tracks are allowed between the lead pads of the capacitor. Screw Terminal capacitors should only
be mounted in an upright position.
Transport: Avoid fumigation and spraying insecticides (especially with bromides) in the import or export
procedures which can cause corrosion. This applies also to the finished devices.
Maintenance: Periodical inspection should be carried out for the capacitor: visual inspection to check
pressure relief open or leakage of electrolyte, electrical characteristics as leakage current, capacitance,
and dissipation factor.
Electrolyte and Separator paper: Electrolyte and separator paper used in Aluminum Capacitors may be
flammable. Also electrolyte is electrically conductive. Therefore in case electrolyte gets in contact with PC
board it may cause corrosion of circuit pattern or cause short circuit between patterns, and may lead to
smoke generation or ignition in worst case.
Caution during Use of Capacitors: Do not touch the terminals of capacitors. Keep the capacitor free
from conductive solution, such as acids, alkali and so on. Ensure that the operating environment of the
equipment into which the capacitor has been built is within the specified conditions mentioned in the
catalogue or specification sheets.
Safety Vent: The safety vent needs some free space to open properly. Allow for free headroom of at least
2mm for diameter ≤16mm, more than 3mm for diameter 18-35mm, more than 5mm for case diameter
40mm and larger.
Emergency Actions: When the pressure relief vent is open and some gas blows out from the capacitor,
please turn the main switch of the equipment off or pull out the plug from the power outlet immediately.
During safety vent operation, extremely hot gas (>100°C) may blow out of the capacitors. Do not stand
close to the capacitors. In case of eye contact, rinse the open eye(s) with clean water immediately. In case
of ingestion, gargle with water immediately, do not swallow. Do not touch electrolyte but wash skin with
soap and water in case of skin contact.
Definition of electrical parameters: Separate documents as application notes, equivalent circuit
diagrams and so on are available on request.
Packaging: Please refer to the data book for details. Further information is available on request.
Jianghai Europe Electronic Components GmbH
2015 v1
Assistance needed? Please contact Jianghai Europe GmbH +49 (0) 2151 652088-72 or [email protected]