JEWEL HILL ELECTRONIC CO.,LTD. JEWEL HILL ELECTRONIC CO.,LTD. SPECIFICATIONS FOR LCD MODULE Module No. JHB240128A E-mail: [email protected] JHB240128A VER: 6.0 Website: www.jhlcd.com -0- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. TABLE OF CONTENTS LCM NUMBER SYSTEM ..................................................................... 2 1. GENERAL DESCRIPTION ........................................................... 3 2. FEATURES...................................................................................... 3 3. MECHANICAL SPECIFICATION .............................................. 3 4. MECHANICAL DIMENSION ....................................................... 4 5. MAXIMUM RATINGS .................................................................. 5 6. ELECTRICAL CHARACTERISTICS ......................................... 5 7. MODULE FUNCTION DESCRIPTION ...................................... 6 8. ELECTRO-OPTICAL CHARACTERISTICS .......................... 15 9. RELIABILITY............................................................................... 19 10. PRECAUTIONS FOR USING LCD MODULES ...................... 20 11. USING LCD MODULES .............................................................. 22 12. REVISION HISTORY .................................................................. 24 SAMPLE APPROVED REPORT ....................................................... 25 JHB240128A VER: 6.0 -1- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. LCM Number System JH B 240128 A S Y E L Y W D A -V00 -SC SPECIAL CODE: P: PIN;C:CONNECT; F:CABLE; H: HEAT SEAL; O: OTHER;TP:WITH TP........ VERSION NUMBER: V00～V99 IC TYPE: A:IC WITH CONTROLLER B:IC WITHOUT CONTROLLER O: OTHER TYPE VIEWING DIRECTION: U: UPPER(12:00); D: DOWN(6:00) L: LEFT(9:00); R: RIGHT(3:00); O: OTHER TEMPERATURE RANGE: N: NORMAL TEMPERATURE RANGE M: MIDDLE TEMPERATURE RANGE W: WIDE TEMPERATURE RANGE S: SUPER WIDE TEMPERATURE RANGE BACKLIGHT COLOR: A: AMBER; B: BLUE; Y: YELLOW-GREEN; G: GREEN; R: RED; W: WHITE; T: DOUBLE LED BACKLIGHT; E: TWO COLOUR LED BACKLIGHT; N: THREE COLOUR LED BACKLIGHT; O: OTHER COLOR; BACKLIGHT TYPE: E: EL; L: LED; C: CCFL; N: NONE; O: OTHER LCD POLARIZER TYPE: R: POSITIVE REFLECTIVE; P: POSITIVE TRANSMISSIVE; E: POSITIVE TRANSFLECTIVE; M: NEGATIVE TRANSFLECTIVE T: NEGATIVE TRANSMISSIVE; LCD COLOR MODE: G: GRAY; Y:YELLOW-GREEN; B: BLUE; W: BLACK-WHITE; O: OTHER; LCD TYPE: F: FSTN; D: DSTN; P: DFSTN; N: TN; H: HTN; S: STN; T: FSC(TN COLOUR); B: BLACK-MARSK. V: VA-BLACK(EBT);O: OTHER; SERIAL NUMBER: A～Z GRAPHIC MODULEs: NUMBER OF COMMONs CHARACTER MODULEs: NUMBER OF LINE GRAPHIC MODULEs:NUMBER OF SEGMENTs CHARACTER MODULEs: LCM TYPE: B: COB & SMT LCM; T: TAB LCM; G: COG LCM; H: HEAT SEAL+LCD(NO IC) LCM; P: FPC+LCD(NO IC) LCM; L: BACKLIGHT+LCD(NO IC) LCM; C: COF LCM; O: OTHER; JEWEL HILL ELECTRONIC CO.,LTD. JHB240128A VER: 6.0 -2- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 1. GENERAL DESCRIPTION The JHB240128A is a 240 x 128 Dots Graphics LCD module. It has a STN panel composed of 240segments and 128 commons. The LCM can be easily accessed by micro-controller via parallel interface. 2. FEATURES Display Mode Display Format Input Data Transflective, Y-G STN module Graphic 240 x 128 dots Parallel data input from MPU Multiplexing Ratio 1/128 Duty Bias 1/13 Bias Viewing Direction 6 O’clock Backlight DC-DC LED (Y-G) Build-in DC-DC converter for negative voltage 3. MECHANICAL SPECIFICATION Item Specifications Unit Dimensional outline 144.0 x 104.0 x 13.5(max) mm Resolution 240segs x 128coms dots View area 114.0(W) x 64.0(H) mm Active area 107.95(W) x 57.55(H) mm Dots pitch 0.45 (W)×0.45(H) mm Dots size 0.4(W)×0.4 (H) mm JHB240128A VER: 6.0 -3- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 4. MECHANICAL DIMENSION *2 *1 TYPE 13.5 --- 8.9 VER: 6.0 R&EL --- LED JHB240128A -4- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 5. MAXIMUM RATINGS Item Symbol Min Max Unit VDD - Vss -0.3 7.0 V VLCD -0.3 24.0 V Input Voltage VIN -0.3 VDD+0.3 Operating temperature TOPR -20 +70 V ℃ Storage temperature TSTR -30 +80 ℃ --- --- 90 %RH Supply voltage Humidity Note 6. ELECTRICAL CHARACTERISTICS Item Symbol Condition Min. Typ. Max. Unit Logic VDD --- --- 5.0 5.5 V H level VIH 0.8VDD --- VDD L level VIL VSS --- 0.2VDD --- 50 60 mA 17.0 17.5 18.0 V 4.8 5.0 5.2 V --- 320 350 mA Supply Voltage Input Voltage --- V VDD=5.0V; Current Consumption (LCD DRIVER) IDD VLCD=17.5V, Tamb=25℃; LCD Driving Voltage VLCD Bias=1/13 VLCD=VDD-V0 Power Supply for LED Vf If=320mA VDD=5.0V; Current Consumption (With LED BackLight) JHB240128A VER: 6.0 If Vf =5.0V,Tamb=25℃; -5- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 7. MODULE FUNCTION DESCRIPTION 7.1. PIN DESCRIPTION Pin No. Symbol Description 1 VSS Power supply for Ground (0V) 2 VCC Power supply for positive (+5V) 3 VO LCD driver voltage regulation pin 4 C/D H:Intraction; 5 /RD Read Enable signed, “L”: Read 6 /WR Write selection signal, ”L”: Write 7 DB0 8 DB1 9 DB2 10 DB3 11 DB4 12 DB5 13 DB6 14 DB7 15 /CE 16 /RST 17 VOUT 18 MD Columns select; “H”: 32; “L”: 40 19 FS Font Selection; “H”: 6*8; “L”: 8*8 L:Data 8-bit bi-directional data bus Chip Enable Signal Reset signal Power supply voltage for LCD driving 20 NC/LEDA No Connect or Supply voltage for LED Positive 21 NC/LEDK No Connect or Supply voltage for LED negative JHB240128A VER: 6.0 -6- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 7.2 TIMING CHARACTERISTICS JHB240128A VER: 6.0 -7- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JHB240128A VER: 6.0 -8- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JHB240128A VER: 6.0 -9- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 7.3 APPLICATION OF LCM Circuit Block Diagram DB0-DB7 /WR /RD /CE C/D FS MD2 RST AD0-AD15 D0-D7 RW CE SRAM SDN8080 T6963C SAP1024B 80SEGs LEDA LEDK SDN8080 80SEGs 80SEGs 80C SDN8080 48C FG VDD VSS VEE SDN8080 LCD PANEL 240*128DOTs SDN8080 POWER SUPPLY CIRCUIT 6 to controller/driver ic LED BACKLIGHT 7.4 TABLE OF COMMAND JHB240128A VER: 6.0 - 10 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 7.5 RAM INTERFACE JHB240128A VER: 6.0 - 11 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 7.6 FLOWCHART OF COMMUNICATION WITH MPU JHB240128A VER: 6.0 - 12 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JHB240128A VER: 6.0 - 13 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JHB240128A VER: 6.0 - 14 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 8. ELECTRO-OPTICAL CHARACTERISTICS Item Symbol LCD driving Condition θ=ψ= 0 VLCD voltage Rise Time (Tr) Temp Min Typ. Max 0℃ --- 18.0 --- 25℃ 17.0 17.5 18.0 50℃ --- 17.0 --- --- --- -- --- ---- --- --- 225 340 --- 240 360 --- --- -- --- --- -- 5 10 --- 0℃ Decay Time (Tf) Rise Time (Tr) Response Time Decay Time (Tf) θ=ψ= 0 Rise Time (Tr) 25℃ 50℃ Decay Time (Tf) Contrast Ratio Cr Viewing Angle Range θ(25℃) θ=ψ= 0 25℃ θ(ψ= 0°) ψ= 90° ψ=180° ψ=270° (6”) (3”) (12”) (9”) 50 35 25 40 CR≥2 Units Note V NOTE1 msec --- NOTE2 NOTE4 備註 Deg NOTE3 z For panel only JHB240128A VER: 6.0 - 15 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. ․Electro-Optical Characteristics Measuring Equipment(DMS501) Printer Detector Positioning (θ,φ) Display Driver LCD Temperature Control System ․Note 1. JHB240128A Illumination (D65) Definition of Driving Voltage( Vlcd) : VER: 6.0 - 16 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. Selected Waveform 100 % 30 % 50 % Non-Selected Waveform 50 % Vth2 Vth1 Operation Voltage Vlcd ․Note 2. Definition of Optical Response Time : NO SELECTED WAVEFORM (10SEC) SELECTED WAVEFORM (10SEC) NO SELECTED WAVEFORM (10SEC) 10% Brightness 100% 90% 100% Tr Tf Rise Time Fall Time t ․Note 3. JHB240128A Definition of Viewing Angle θ and ψ : VER: 6.0 - 17 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. Normal : θ=0° 12 O’clock Direction φ=180° θ φ=90° φ=270° 9 O’clock Direction 3 O’clock Direction φ φ=0° Viewing Direction 6 O’clock Direction ․Note 4. Definition of Contrast ratio( CR) : Brightness (%) CR = Brightness of Non-selected Segment (B2) Brightness of Selected Segment (B1) Brightness Curve for Selected Segment B2 100% Brightness Curve for Non-selected Segment CR,max B1 0% Driving Voltage V,max JHB240128A Contrast VER: 6.0 - 18 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 9. RELIABILITY 9.1. MTBF The LCD module shall be designed to meet a minimum MTBF value of 30000 hours with normal. (25°C in the room without sunlight) 9.2. TESTS NO. 1 2 ITEM High Temperature Operating Low Temperature Operating 70℃ -20℃ CONDITION 120Hrs CRITERION 。No Defect Of 120Hrs Operational Function In Room Temperature Are Allowable. 。IDD of LCM in 3 High Temperature/ Humidity Non-Operating 60℃ ,90%RH ,120 Hrs 4 High Temperature Non-Operating 80℃ 120Hrs 5 Low Temperature Non-Operating -30℃ 120Hrs 6 Temperature Cycling Non-Operating -20℃(30Min )↔ 60℃(30Min) Pre-and post-test should follow specification 10 CYCLES Notes: Judgments should be mode after exposure in room temperature for two hours. JHB240128A VER: 6.0 - 19 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 10. PRECAUTIONS FOR USING LCD MODULES 10.1. HANDLING PRECAUTIONS (1) The display panel is made of glass. Do not subject it to a mechanical shock or impact by dropping it. (2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the substance contacts your skin or clothes, wash it off using soap and water. (3) Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. (4) The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. (5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If it is heavily contaminated, moisten a cloth with one of the following solvents: - Isopropyl alcohol - Ethyl alcohol (6) Solvents other than those above mentioned may damage the polarizer. Especially, do not use the following: - Water - Ketone - Aromatic solvents (7) Extra care to minimize corrosion of the electrode. Water droplets, moisture condensation or a current flow in a high-humidity environment accelerates corrosion of the electrode. (8) Install the LCD Module by using the mounting holes. When mounting the LCD Module, make sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the backlight cable. (9) Do not attempt to disassemble or process the LCD Module. (10) NC terminal should be open. Do not connect anything. (11) If the logic circuit power is off, do not apply the input signals. (12) To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. - Be sure to ground the body when handling he LCD Module. - Tools required for assembling, such as soldering irons, must be properly grounded. -To reduce the amount of static electricity generated, do not conduct assembling and other work under dry conditions. JHB240128A VER: 6.0 - 20 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. -The LCD Module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated. 10.2. STORAGE CONDITIONS When storing, avoid the LCD module to be exposed to direct sunlight of fluorescent lamps. For stability, to keep it away form high temperature and high humidity environment (The best condition is : 23±5°C, 45±20%RH). ESD protection is necessary for long-term storage also. 10.3. OTHERS Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low temperature. If the LCD Module have been operating for a long time showing the same display patterns the display patterns may remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating status can be recovered by suspending use for some time. It should be noted that this phenomenon does not adversely affect performance reliability. To minimize the performance degradation of the LCD Module resulting from destruction caused by static electricity etc. exercise care to avoid holding the following sections when handling the modules. - Exposed area of the printed circuit board. - Terminal electrode sections. JHB240128A VER: 6.0 - 21 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 11. Using LCD modules 11.1 LIQUID CRYSTAL DISPLAY MODULES LCD is composed of glass and polarizer. Pay attention to the following items when handling. (1) Please keep the temperature within specified range for use and storage. Polarization degradation, bubble generation or polarizer peel-off may occur with high temperature and high humidity. (2) Do not touch, push or rub the exposed polarizers with anything harder than a HB pencil lead (glass, tweezers, etc). (3) N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors made of organic substances, which will be damaged by chemicals such as acetone, toluene, toluene, ethanol and isopropyl alcohol. (4) When the display surface becomes dusty, wipe gently with absorbent cotton or other soft material like chamois soaked in petroleum ether. Do not scrub hard to avoid damaging the display surface. (5) Wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or color fading. (6) Avoid contacting oil and fats. (7) Condensation on the surface and contact with terminals due to cold will damage, stain or polarizers. After products are tested at low temperature they must be warmed up in a container before coming is contacting with room temperature air. (8) Do not put or attach anything on the display area to avoid leaving marks on. (9) Do not touch the display with bare hands. This will stain the display area and degrade insulation between terminals (some cosmetics are determinate to the polarizers). (10)As glass is fragile, it tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. 11.2 INSTALLING LCD MODULE Attend to the following items when installing the LCM. (1) Cover the surface with a transparent protective plate to protect the polarizer and LC cell. (2) When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting plate should have enough height to avoid causing stress to the module surface, refer to the individual specifications for measurements. The measurement tolerance should be ±0.1mm. 11.3 ELECTRO-STATIC DISCHARGE CONTROL Since this module uses a CMOS LSI, the same careful attention should be paid for electrostatic discharge as for an ordinary CMOS IC. JHB240128A VER: 6.0 - 22 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. (1) Make certain that you are grounded when handing LCM. (2) Before removing LCM from its packing case or incorporating it into a set, be sure the module and your body have the same electric potential. (3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak. (4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor. (5) As far as possible, make the electric potential of your work clothes and that of the workbenches to the ground potential. (6) To reduce the generation of electro-static discharge, be careful that the air in the work is not too dried. A relative humidity of 50%-60% is recommended. 11.4 PRECAUTIONS FOR OPERATION (1) Viewing angle varies with the change of liquid crystal driving voltage (Vo). Adjust Vo to show the best contrast. (2) Driving the LCD in the voltage above the limit will shorten its lifetime. (3) Response time is greatly delayed at temperature below the operating temperature range. However, this does not mean the LCD will be out of the order. It will recover when it returns to the specified temperature range. (4) If the display area is pushed hard during operation, the display will become abnormal. However, it will return to normal if it is turned off and then on. (5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. Therefore, this product must be used and stored within the specified condition of 23±5°C, 45±20%RH. (6) When turning the power on, input each signal after the positive/negative voltage becomes stable. 11.5 SAFETY (1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned. (2) If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash off thoroughly with soap and water. JHB240128A VER: 6.0 - 23 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 12. REVISION HISTORY Version Revise record Date 1.0 Original version 05-01-01 2.0 Change LCD voltage 05-07-05 3.0 Change specification format 05-11-20 4.0 Change contact mode 06-08-04 5.0 09-12-05 5.01 Change module temperature from normal to wide temperature Perfect the VER5.0 spec，Commany internal modify. 6.0 LCM for Y-G mode ,transflective,Y-G LED 13-08-01 JHB240128A VER: 6.0 - 24 - 13-08-01 Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. SAMPLE APPROVED REPORT (样品确认单) SAMPLE MODEL NO. (样品型号) JHB240128A SAMPLE SERIES NUMBER NO. (样品序号) SAMPLE QUANTITY (样品数量) COLOR/TYPE (底色/类型) STN/Y-G VIEWING DIRECTION (视角) 6:00 DRIVING METHOD (驱动参数) 1/128Duty, 1/13Bias LOGIC VOLTAGE (工作电压) 5.0V LCD VOP (LCD 驱动电压) 17.5V OPERATING TEMP. (操作温度) ℃ -20--70 STORAGE TEMP. (储存温度) ℃ -30--80 POLARIZER----FRONT (首偏光片) POLARIZER----BACK (后偏光片) Transflective CONTROLLER/DRIVER IC(控制/驱动 IC) T6963C/SAP1024B/EQUIV BACKLIGHT COLOR/TYPE (背光源类型/颜色) LED/Y-G DRAWING REV/NO./QUANTITY (图纸版本/数量) SPECIFICATION (规格书 份数) REMARKS： (备注) WRIT BY：_________ DATE：_________ APROV BY：_________ DATE：________ CUSTOMER’S APPROVAL (客户确认)： 1） FUNCTION （功能）： OK N.G. 2） DRIVER CONDITION （驱动条件）： OK N.G. 3） DISPLAY MODE （显示模式）： OK N.G. 4） VIEWING ANGLE （视角）： OK N.G. 5） BACKLIGHT （背光源）： OK N.G. 6） DISPLAYING PATTERN （显示效果）： OK N.G. CUSTOMER’S CONCLUSIONS (客户意见)：______________________________________ _______________________________________________________________________________ ________________________________________ CUSTOMER’S SIGNATURE（客户签名）：_____________ DATE (日期)：___________ JHB240128A VER: 6.0 - 25 - Issue date: 2013/08/01