HMC835LP6GE

Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
PLLs WITH INTEGRATED VCO - SMT
Features
1
Wideband: 33 - 4100 MHz
External LO Input
Maximum Phase Detector Rate: 100 MHz
Exact Frequency Mode:
0 Hz Fractional Frequency Error
Low Phase Noise: -110 dBc/Hz in Band @2GHz
PLL FOM:
-230 dBc/Hz Integer Mode, -227 dBc/Hz Fractional
Mode
Programmable RF Output Phase
Output Phase Synchronous Frequency Changes
Output Phase Synchronization
< 94 fs Integrated RMS Jitter (1 kHz to 100 MHz)
RF Output Mute Function
Low Noise Floor: -167 dBc/Hz
40 Lead 6x6 mm SMT Package: 36 mm 2
2 Differential RF outputs
Typical Applications
• MIMO Radio Architectures
• Phased Array Applications
• Cellular Infrastructure
• DDS Replacement
• Cellular backhaul
• Communication Test Equipment
• CATV Equipment
Functional Diagram
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
The HMC835LP6GE is a low noise, wide band, Fractional-N PLL that features an integrated VCO with a fundamental
frequency of 2050 to 4100 MHz, and an integrated VCO Output Divider (divide by 2/4/6/.../60/62) that together enable
the HMC835LP6GE to generate frequencies from 33 MHz to 4100 MHz. Integrated Phase Detector (PD) and a deltasigma modulator capable of operating at up to 100 MHz enable wider loop-bandwidths, faster frequency changes along
with excellent spectral performance.
Two independent RF outputs, with independent gain control, enable the HMC835LP6GE to distribute identical
frequency and phase signals to multiple destinations, at optimal signal levels tailored to each output.
An external VCO input allows the HMC835LP6GE to lock external VCOs, and enables cascaded LO architectures for
MIMO radio applications. Two separate Charge Pump (CP) outputs enable separate loop filters optimized for both
integrated and external VCOs, and seamless switching between integrated or external VCOs during operation.
Programmable RF output phase feature can further phase adjust and synchronize multiple HMC835LP6GEs enabling
scalable MIMO and beam-forming radio architectures.
Additional features include configurable output mute function that mutes RF outputs during frequency changes, Exact
Frequency Mode that enables the HMC835LP6GE to generate fractional frequencies with 0 Hz frequency error, and
the ability to synchronously change frequencies without changing the phase of the output signal.
Electrical Specifications
VPPCP, VDDLS, VCC1, VCC2 = 5 V; RVDD, AVDD, DVDD, VCCPD, VCCHF, VCCPS = 3.3 V Min and Max Specified
across Temp -40 °C to 85 °C
Parameter
Condition
Min.
Typ.
Max.
Units
33
4100
MHz
VCO Frequency at PLL Input
2050
4100
MHz
RF Output Frequency at f VCO
2050
4100
MHz
RF Output Characteristics
Output Frequency
PLLs WITH INTEGRATED VCO - SMT
General Description
Output Power
Max Gain Setting
Reg 16h[7:6]=11
Differential (100 Ohm load).
Output power varies with
frequency and output configuration.
See Figures 11, 12, 13, 14
5
dBm
3 dB Steps
9
dB
fo Mode at 2 GHz
2nd / 3rd / 4th
-26/-20/-39
dBc
fo/2 Mode at 2GHz/2 = 1 GHz
2nd / 3rd / 4th
-27/-17/-35
dBc
fo/30 Mode at 3 GHz/30 = 100 MHz
2nd / 3rd / 4th
-26/-10/-38
dBc
RF Output Power at fundmental frequency at
2050 MHz
Output Power Control range
Harmonics for Fundamental Mode
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
2
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
PLLs WITH INTEGRATED VCO - SMT
Electrical Specifications (Continued)
Parameter
fo/62 Mode at 3999 MHz/62 = 64.5 MHz
Condition
Min.
2nd / 3rd / 4th
Typ.
Max.
-23/-10/-31
Units
dBc
VCO Output Divider
VCO RF Divider Range
Parameter
1,2,4,6,8,...,62
1
62
Condition
Min.
Typ.
Max.
Max = 219 - 1
16
524,287
Fractional nominal divide ratio
varies (+/- 4) dynamically max
20
524,283
Units
PLL RF Divider Characteristics
19-Bit N-Divider Range (Integer)
19-Bit N-Divider Range (Fractional)
REF Input Characteristics
Max Ref Input Frequency
Ref Input Level
AC Coupled [1]
350
MHz
-6
12
dBm
5
pF
1
16,383
DC
100
MHz
DC
100
MHz
0.02
2.54
mA
Ref Input Capacitance
14-Bit R-Divider Range
Phase Detector (PD) [2]
PD Frequency Fractional Mode
[3]
PD Frequency Integer Mode
Charge Pump
Output Current
Charge Pump Gain Step Size
PD/Charge Pump SSB Phase Noise
20
µA
50 MHz Ref, Input Referred
1 kHz
-143
dBc/Hz
10 kHz
Add 2 dB for Fractional
-150
dBc/Hz
100 kHz
Add 3 dB for Fractional
-153
dBc/Hz
0.9
V
1.8/3.3
V
Logic Inputs
Vsw
Logic Outputs
VOH Output High Voltage
VOL Output Low Voltage
Output Impedance
0
100
Maximum DC current to a load
V
200
Ω
1.5
mA
[1] Measured with 100 Ω external termination. See “1.3.2 Reference Input Stage” section for more details.
[2] Slew rate of ≥ 0.5 ns/V is recommended, see “1.3.2 Reference Input Stage” section for more details. Frequency is guaranteed across process
voltage and temperature from -40 °C to +85 °C.
[3] This maximum PD frequency can only be achieved if the minimum N value is respected. eg. In the case of fractional mode, the maximum PD
frequency = fvco/20 or 100 MHz, whichever is less.
3
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Parameter
Condition
Min.
Typ.
Max.
Units
AVDD, VCCHF, VCCPS,
3VRVDD,DVDD3V,VCCPD
3.1
3.3
3.5
V
VCC1,VCC2,VDDLS, VDDCP
4.8
5
5.2
V
Power Supply Voltages
3.3 V Supplies
5 V Supplies
Power Supply Currents
+5V Analog Charge Pump (VDDCP)
+5V VCO core + LO1 Buffer Only (VCC2)
+5V VCO core + LO2 Buffer Only (VCC2)
+5V VCO core + LO1 Buffer + LO2 Buffer
(VCC2)
+5V VCO Divider and RF/PLL Buffer (VCC1)
6
Single-Ended
Output[4]
Differential Output [4]
99
110
104
129
Single-Ended Output[4]
99
110
Differential Output [4]
104
129
Single-Ended Output[4]
108
130
Differential Output [4]
118
168
Fo/1 Mode
Fo/N (2,4...62) Mode
mA
27
52
+3.3V VCCPD, VCCPS, VCCHF, DVDD,
RVDD
73
48
Power Down - Crystal Off
Reg 01h=0,
Crystal Not Clocked
(5V and 3.3V combined)
1
µA
Power Down - Crystal On, 100 MHz
Reg 01h=0,
Crystal Clocked 100 MHz
5
mA
700
mV
Power on Reset
Typical Reset Voltage on DVDD
Min DVDD Voltage for No Reset
Power on Reset Delay
1.5
PLLs WITH INTEGRATED VCO - SMT
Electrical Specifications (Continued)
V
250
µs
-78
dBc/Hz
VCO Open Loop Phase Noise at fo @ 4 GHz
10 kHz Offset
100 kHz Offset
-108
dBc/Hz
1 MHz Offset
-134.5
dBc/Hz
10 MHz Offset
-156
dBc/Hz
100 MHz Offset
-171
dBc/Hz
-89
dBc/Hz
VCO Open Loop Phase Noise at fo @ 3 GHz/2 = 1.5 GHz
10 kHz Offset
100 kHz Offset
-119
dBc/Hz
1 MHz Offset
-143.7
dBc/Hz
10 MHz Offset
-160.7
dBc/Hz
100 MHz Offset
-167
dBc/Hz
[4] Minimum and Maximum current various by different Gain settings from 0 to 3
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
4
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Electrical Specifications (Continued)
PLLs WITH INTEGRATED VCO - SMT
Parameter
Min.
Typ.
Max.
Units
VCO Open Loop Phase Noise at fo @3 GHz/30 = 100 MHz
10 kHz Offset
-111
dBc/Hz
100 kHz Offset
-142
dBc/Hz
1 MHz Offset
-167
dBc/Hz
10 MHz Offset
-170
dBc/Hz
100 MHz Offset
-171
dBc/Hz
PLL Figure of Merit (FOM)
Floor Integer Mode (Fig 28)
Normalized to 1 Hz
-230
dBc/Hz
Floor Fractional Mode (Fig 28)
Normalized to 1 Hz
-227
dBc/Hz
Flicker (Both Modes) (Fig 28)
Normalized to 1 Hz
-268
dBc/Hz
15
MHz/V
14.5
MHz/V
16.2
MHz/V
14.6
MHz/V
15.4
MHz/V
14.8
MHz/V
2
MHz/V
VCO Characteristics
VCO Tuning Sensitivity at 3862 MHz
VCO Tuning Sensitivity at 3643 MHz
VCO Tuning Sensitivity at 3491 MHz
VCO Tuning Sensitivity at 3044 MHz
VCO Tuning Sensitivity at 2558 MHz
VCO Tuning Sensitivity at 2129 MHz
VCO Supply Pushing
5
Condition
Measured with 2.5 V
on VTUNE; see Fig 7
Measured with 2.5 V
on VTUNE; see Fig 7
Measured with 2.5 V
on VTUNE; see Fig 7
Measured with 2.5 V
on VTUNE; see Fig 7
Measured with 2.5 V
on VTUNE; see Fig 7
Measured with 2.5 V
on VTUNE; see Fig 7
Measured with 2.5 V
on VTUNE
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Typical Performance Characteristics
Figure 2. Closed Loop Fractional Phase
Noise at 3600 MHz, Divided by 1 to 62 [1][5]
-80
-80
PHASE NOISE(dBc/Hz)
PHASE NOISE(dBc/Hz)
-100
-120
-140
-160
-120
-140
-160
-180
-200
-100
1
10
100
1000
10000
-180
100000
1
10
Div1
Div4
Div16
Div2
Div8
Div32
Div62
Figure 3. Closed Loop Phase Noise at
3300 MHz, Divided by 1 to 62 [2][5]
PHASE NOISE(dBc/Hz)
PHASE NOISE (dBc/Hz)
100000
Div1
Div4
Div16
Div2
Div8
Div32
Div62
-100
-120
-140
-160
-120
-140
-160
-180
1
10
100
1000
10000
-200
100000
1
10
OFFSET (KHz)
100
1000
10000
100000
OFFSET (KHz)
Div1
Div4
Div16
Div2
Div8
Div32
Div62
Figure 5. Closed Loop Phase Noise at
3300MHz for different Loop Filter [4][5]
Div1
Div4
Div16
Div2
Div8
Div32
Div62
Figure 6. Free Running VCO Phase Noise
-80
-40
-60
PHASE NOISE(dBc/Hz)
-100
PHASE NOISE(dBc/Hz)
10000
-80
-100
-120
-140
-160
-180
-200
1000
Figure 4. Closed Loop Phase Noise at
3300 MHz, Divided by 1 to 62 [3][5]
-80
-180
100
OFFSET (KHz)
OFFSET (KHz)
PLLs WITH INTEGRATED VCO - SMT
Figure 1. Closed Loop Fractional Phase
Noise at 4100 MHz, Divided by 1 to 62[1][5]
-80
-100
-120
-140
-160
1
10
100
1000
10000
100000
-180
1
10
OFFSET (KHz)
INT MODE, Loop Filter BW 186 KHz, Integrated Jitter 94 fs
FRAC MODE, Loop Filter BW 186 KHz, Integrated Jitter 124 fs
INT MODE, Loop Filter BW 58 KHz, Integrated Jitter 141 fs
FRAC MODE, Loop Filter BW 58 KHz, Integrated Jitter 141 fs
100
1000
10000
100000
OFFSET (KHz)
4090 MHz
3570 MHz
2627 MHz
3861 MHz
3120 MHz
2185 MHz
[1] Measured with 122.88 MHz Xtal, 61.44 MHz PD frequency, Loop Filter #1, CP = 2.54 mA, Offset Dn = 435 uA.
[2] Measured with 100 MHz Xtal, 50 MHz PD frequency, Loop Filter #1, CP = 2.54 mA, Offset Dn = 435 uA.
[3] Measured with 100 MHz Xtal, 50 MHz PD frequency, Loop Filter #2, CP = 2.54 mA, Offset Dn = 435 uA.
[4] Measured with 100 MHz Xtal, 50 MHz PD frequency, Loop Filter #1 and Loop Filter #2, CP= 2.54 mA. Offset Dn = 435 uA. Phase Noise integrated
from 1 kHz to 100 MHz
[5] Loop Filter designs are provided in Table 1
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
6
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Figure 7. Typical VCO Sensitivity
Figure 8. Typical Tuning Voltage After
Calibration [6]
80
TUNE VOLTAGE AFTER CALIBRATION (V)
5
KVCO (MHz/V)
60
50
40
30
20
10
0
0
1
2
3
4
5
4
3
2
1
fmin
fmax
0
1900 2100 2300 2500 2700 2900 3100 3300 3500 3700 3900 4100 4300
TUNING VOLTAGE (V)
VCO FREQUENCY(MHz)
ML core, Tuning Cap 15
H core, Tuning Cap 7
MH core, Tuning Cap 7
CL core, Tuning Cap 15
L core, Tuning Cap 15
CH core, Tuning Cap 15
Figure 9. Open Loop Phase Noise
vs. Temp
Calibrated at 85C, Measured at 85C
Calibrated at 85C, Measured at -40C
Calibrated at -40C, Measured at -40C
Calibrated at -40C, Measured at 85C
Calibrated at 27C, Measured at 27C
Figure 10. Single Sideband Integrated
Phase Noise [7]
0.3
-100
-110
100 kHz Offset
INTEGRATED JITTER (ps)
PHASE NOISE (dBc/Hz)
PLLs WITH INTEGRATED VCO - SMT
70
-120
-130
1 MHz Offset
-140
-150
-160
0.25
0.2
0.15
0.1
0.05
-170
100 MHz Offset
-180
30
100
0
300
1000
4000
0
500
1000
27 C
-40 C
15
15
10
10
5
0
-5
-10
2000
2500
3000
3500
4000
27 C
85 C
Figure 12. Single-Ended Output Power
(LO1_N, LO2_P) [9]
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
-40 C
85 C
Figure 11. Differential Output Power (LO1,
LO2) [8] [9]
1500
OUTPUT FREQUENCY (MHz)
FREQUENCY (MHz)
5
0
-5
100
1000
OUTPUT FREQUENCY (MHz)
ONE OUTPUT ENABLE(LO1 or LO2)
-10
100
1000
OUTPUT FREQUENCY (MHz)
BOTH OUTPUTS ENABLE(LO1&LO2)
[6] The HMC835LP6GE features an internal AutoCal process that seamlessly calibrates the HMC835LP6GE when a frequency change is executed.
Once calibrated, at any temperature, the calibration setting holds across the entire operating range of the HMC835LP6GE (-40 ˚C to +85 ˚C). Fig 10
shows that the tuning voltage of the HMC835LP6GE is maintained within a narrow operating range for worst case scenarios where calibration was
executed at one temperature extreme and the HMC835LP6GE is operating at the other extreme.
[7] 100 MHz Xtal, 50 MHz PD frequency. Loop Filter #1 with CP and Offset scaling. Phase Noise integrated from 1 kHz to 100 MHz
[8] This is the measured power into 50 Ohm load to ground on each of the differential output legs, LO_N & LO_P. Output power into differential 100
Ohm load is ~3dB higher.
[9] Gain Setting: Reg 16h[7:6] = 11 and Reg 16h[9:8] = 11; Divider Boost setting: Reg 16h[10] = 1 measured at 27C
7
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
15
10
10
5
0
5
0
-5
-5
-10
-10
100
100
1000
OUTPUT FREQUENCY (MHz)
1000
OUTPUT FREQUENCY (MHz)
85C
Figure 15. Typical Differential Output Power
vs10 Frequency and Gain [8]
-40C
27C
Figure 16. Fractional Spurious Performance
at 904 MHz, Exact Frequency Mode ON [10]
0
-40
5
PHASE NOISE (dBc/Hz)
OUTPUT POWER (dBm)
-20
0
-5
-60
-80
-100
-120
-140
-160
-10
500
1000
1500
2000
2500
3000
3500
-180
4000
1
OUTPUT FREQUENCY (MHz)
Gain 11
Gain 10
100
1000
10000
100000
OFFSET (kHz)
Gain 01
Gain 00
Figure 17. Fractional Spurious Performance
at 1804 MHz, Exact Frequency Mode ON [10]
Figure 18. Fractional Spurious Performance
at 2646.96 MHz, Exact Frequency Mode ON [11]
-40
0
-20
-60
PHASE NOISE(dBc/Hz)
-40
PHASE NOISE (dBc/Hz)
10
PLLs WITH INTEGRATED VCO - SMT
15
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
Figure 13. Single-Ended Output Power LO1_N or Figure 14. Typical Differential Output Power vs
LO2_P When Other Port operating Differential [9] Frequency and Temp(Max Gain 11) [8] [9]
-60
-80
-100
-120
-80
-100
-120
-140
-140
-160
-160
-180
-180
1
10
100
1000
OFFSET (kHz)
10000
100000
1
10
100
1000
10000
100000
OFFSET (KHz)
[10] 100 MHz Xtal, PD 50 MHz, Channel Spacing = 200 KHz, Loop Filter #1 from Table 1. Exact Frequency Mode ON.
[11] 122.88 Xtal, PD 61.44. Loop Filter #1 from Table 1 is used. Channel spacing 240 KHz. Exact Frequency Mode ON
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
-40
-120
-60
-130
-80
PHASE NOISE (dBc/Hz)
PHASE NOISE(dBc/Hz)
Figure 20. Low Frequency Performance [13]
-140
-100
-150
-120
-160
-140
-170
-160
-180
1
10
100
1000
10000
-180
0.1
100000
1
10
100
OFFSET (KHz)
1000
10000
100000
OFFSET (kHz)
Carrier Frequency = 33.0645 MHz
Carrier Frequency = 50 MHz
Carrier Frequency = 100 MHz
Figure 21. Typical Spurious Emissions at
3000.1 MHz, Fixed Reference [14]
Figure 22. Typical Spurious Emissions at
3000.1 MHz, Tunable Reference [15]
0
0
-20
-20
-40
-40
PHASE NOISE (dBc/Hz)
PHASE NOISE (dBc/Hz)
PLLs WITH INTEGRATED VCO - SMT
Figure 19. Fractional Spurious Performance at
2646.96 MHz, Exact Frequency Mode OFF [12]
-60
-80
-100
-120
-140
-160
-60
-80
-100
-120
-140
-160
-180
-180
1
10
100
1000
10000
100000
1
10
100
OFFSET (kHz)
10000
100000
Figure 24. Reference Input Sensitivity, Square
Wave [17]
-40
-220
-50
-222
-224
-60
FOM (dBc/Hz)
WORST SPUR (dBc)
Figure 23. Typical Spurious vs Offset from 3
GHz, Fixed vs. Tunable Reference [16]
-70
-80
-226
-228
-230
-90
-232
-100
3GHz +1kHz
1000
OFFSET (kHz)
3GHz +10kHz
3GHz +100kHz
3GHz +1000kHz
OUTPUT FREQUENCY
Fixed 50 MHz Reference
-234
-15
-12
-9
-6
-3
0
3
REFERENCE POWER (dBm)
Tunable Reference
14 MHz Square Wave
50 MHz Square Wave
25 MHz Square Wave
100 MHz Square Wave
[12] 122.88 Xtal, PD 61.44. Loop Filter #1 from Table 1 is used. Channel spacing 240 KHz. Exact Frequency Mode OFF
[13] 100 MHz Xtal, PD Frequency 50 MHz, Loop Filter #3 from Table 1 is used. CP = 2.54 mA. Set to Integer Mode.
[14] 100 MHz Xtal, PD Frequency 50 MHz,Loop Filter #1 from Table 1 is used. The plot shows an integer boundary spur inside the loop filter bandwidth.
[15] The tunable reference is used to change the reference frequency from 50 MHz in Fig 22 to 47.5 MHz in Fig 23 in order to distance the integer
boundary spur away from the carrier frequency so that it is filtered by the loop filter. Loop Filter Type 1 from Table 1 is used.
[16] The plot is generated by recoding the magnitude of the largest spur only at any offset, at each output frequency, while using a fixed 50MHz
reference, and a tunable 47.5 MHz reference.See detail procedure discussed in [17]. Contact Hittite Apps Support to obtain the required configuration
to achieve similar spurious performance throughout the operating range of the HMC835LP6GE.
[17] Measured from a 50 Ω source with a 100 Ω external resistor termination.
9
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Figure 25. Reference Input Sensitivity,
Sinusoidal Wave [17]
Figure 26. Phase Adjust at 0 degree[18]
-200
-205
500
AMPLITUDE (mV)
FOM (dBc/Hz)
-210
-215
-220
-225
0
-500
-230
-235
-1000
-20
-15
-10
-5
0
5
-500
-400
-300
REFERENCE POWER (dBm)
14 MHz sin
50 MHz sin
25 MHz sin
100 MHz sin
1000
500
500
AMPLITUDE(mV)
AMPLITUDE(mV)
0
100
200
300
Figure 28. Phase Adjust at 180 degree [20]
1000
0
-500
0
-500
-1000
-1000
-400
-200
0
200
-600
-400
TIME(ps)
-200
0
200
TIME(ps)
Figure 30. RF Output Return Loss Diff [21]
Figure 29. Figure of Merit
-200
0
-5
-210
RETURN LOSS (dB)
NORMALIZED PHASE NOISE (dBc/Hz)
-100
TIME(ps)
Figure 27. Phase Adjust at 90 degree [19]
-600
-200
PLLs WITH INTEGRATED VCO - SMT
1000
Typ FOM vs Offset
-220
FOM Floor
FOM 1/f Noise
-10
Return Loss (LO DIFFERENTIAL OUTPOUT)
-15
-20
-230
-25
-240
2
10
10
3
10
4
OFFSET (Hz)
10
5
10
6
-30
100
1000
OUTPUT FREQUENCY (MHz)
[18] Loop Filter #1 from Table 1 used. Phase adjust feature limited to Fundamental Mode operation (2050 to 4100MHz). The plot is capture by using
two identical HMC835LP6GE eval boards driven by the same 10MHz external reference source from instrument via on board HMC1031MS8E to
generate a 50 MHz reference frequency to lock with HMC835LP6GE, and captured with 26GHz 50 Ω high speed Oscilloscope. Seed value in Reg1A
for both HMC835LP6GE initially set to 0. Then Reg1A was adjusted in HMC835LP6GE #1 to bring the phase into alignment with HMC835LP6GE #2.
[19] Phase adjust feature limited to Fundamental Mode operation (2050 to 4100MHz). Starting condition as stated in [18] then HMC835LP6GE #2 seed
value Reg 1Ah set to 400000h. Required seed value calculated from (Phase Adjust (degrees)/360˚ x 224.
[20] Phase adjust feature limited to Fundamental Mode operation (2050 to 4100MHz). Starting condition as stated in [18] then HMC835LP6GE #2
seed value Reg 1Ah set to 800000h.
[21] Both LO1 and LO2 Output Buffer Enabled in Reg 17h[5:4] as 11.Differential or single-ended mode programmed in Reg 17h[9:8].
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
10
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Figure 31. RF Output Return Loss Diff [21]
Figure 32. Frequency Settling After
Frequency Change, AutoCal Enabled [22]
2.02
2.015
Return Loss (LO SINGLE ENDED OUTPOUT)
FREQUENCY (GHz)
RETURN LOSS (dB)
-5
-10
-15
-20
Settling Time to < 5 Degrees
Phase Error
2.01
2.005
2
1.995
Note: Loop Filter Bandwidth = 186 kHz, Loop Filter
Phase Margin = 48 degrees.This result is directly
affected by loop filter design. Faster settling time
is possilbe with wider loop filter bandwidth and lower
phase margin.
1.99
-25
1.985
-30
100
1.98
1000
0
20
40
Figure 33. Phase Settling After Frequency
Change, AutoCal Enabled [22]
200
2.02
FREQUENCY (GHz)
Settling Time to < 5 Degrees
Phase Error
50
0
-50
-100
0
20
40
60
80
Settling Time to < 5 Degrees
Phase Error
2.01
2.005
2
1.995
Note: Loop Filter Bandwidth = 186 kHz, Loop Filter
Phase Margin = 48 degrees.This result is directly
affected by loop filter design. Faster settling time
is possilbe with wider loop filter bandwidth and lower
phase margin.
1.99
Note: Loop Filter Bandwidth = 186 kHz, Loop Filter
Phase Margin = 48 degrees.This result is directly
affected by loop filter design. Faster settling time
is possilbe with wider loop filter bandwidth and lower
phase margin.
-150
1.985
1.98
100
0
20
40
TIME (us)
60
80
100
TIME (us)
Figure 35. Phase Settling After Frequency
Change, Manual Calibration [23]
200
Figure 36. External VCO Port Gain
(Ext VCO In to LO Out) [24]
FORWARD TRANMISSION GAIN (dB)
20
150
PHASE ERROR (DEGREES)
100
2.015
100
Settling Time to < 5 Degrees
Phase Error
100
50
0
-50
-100
Note: Loop Filter Bandwidth = 186 kHz, Loop Filter
Phase Margin = 48 degrees.This result is directly
affected by loop filter design. Faster settling time
is possilbe with wider loop filter bandwidth and lower
phase margin.
-150
-200
80
Figure 34. Frequency Settling After
Frequency Change, Manual Calibration [23]
150
-200
60
TIME (us)
OUTPUT FREQUENCY (MHz)
PHASE ERROR (DEGREES)
PLLs WITH INTEGRATED VCO - SMT
0
0
20
40
60
80
100
S21 Differential external input to Differential LO output
15
10
5
0
-5
TIME (us)
S21 Single-ended external input to Single-ended LO output
400
800
1200
1600
2000
2400
2800
OUTPUT FREQUENCY (MHz)
[22] The HMC835LP6GE features an internal AutoCal process that seamlessly calibrates the HMC835LP6GE when a frequency change is executed.
Typical frequency settling time that can be expected after any frequency change (Reg 03h or Reg 04h writes) is shown in Fig 31 with AutoCal enabled
(Reg 0Ah[11] = 0). Frequency hop of 5 MHz is shown in Fig 31, however the settling time is independent of the size of the frequency change. Any size
frequency size hop will have a similar settling time with AutoCal enabled. Loop BW = 186 kHz (Loop Filter #1 in Table 1).
[23] For applications that require fast frequency changes, the HMC835LP6GE supports manual calibration that enables faster settling times. Manual
calibration needs to be executed only once for each individual HMC835LP6GE, at any temperature, and is valid across all temperature operating
range of the HMC835LP6GE. More information about manual calibration is available in section 1.2.1.6. Frequency hop of 5 MHz is shown in Fig 33
and Fig 34 however the settling time is independent of the size of the frequency change. Any size frequency size hop will have a similar settling time
with AutoCal disabled (Reg 0Ah[11] = 1). Loop BW = 186 kHz (Loop Filter #1 in Table 1).
[24] 0dbm IN. External Buffer Bias is configured in Reg 18h[20:19] as 11. Both LO1 and LO2 Output Buffer Enabled in Reg 17h[5:4] as 11.Differential
or single-ended mode programmed in Reg 17h[9:8].
11
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Figure 38. HMC835LP6GE Mute and
Isolations
0
-40
Signal on LO2_N pin when LO2 Buffer is on,
LO2 Single-Ended Mode is on,
Mute Off
-24
-80
ISOLATION (dB)
PHASE NOISE(dBc/Hz)
-60
-100
-120
Signal on LO1_P pin when LO1 Buffer is on,
LO1 Single-Ended Mode is on,
Reg 17h[5:4]=1d, Reg17h[9:8]=0d
Mute Off
-48
-72
Signal on LO2_P pin when LO2 Buffer is off,
LO1 buffer is on, Reg 17h[5:4]=1d, Reg17h[9:8]=3d
Mute Off
Mute when unlock Reg 17h[7]=1
-140
-96
-160
-180
Mute On (Reg16h[5:0] = 0d)
1
10
100
1000
-120
100
10000
OFFSET (KHz)
FRQUENCY (MHz)
1000
3000
Table 1. Loop Filter Designs Used in Typical Performance Characteristics Graphs
Loop
Filter
ID
Loop
BW
(kHz)
Loop
Phase
Margin
C1
(pF)
C2
(nF)
C3
(pF)
C4
(pF)
R2
(Ω)
R3
(Ω)
R4
(Ω)
#1 [26]
161
53°
180
6.8
47
47
2200
1000
1000
#2 [27]
80
56°
56
22
220
220
1000
1000
1000
#3 [28]
214
61°
56
1.8
NA
NA
2200
0
0
#4 [29]
17
66°
3300
330
1500
4700
75
75
12
Loop Filter Design
PLLs WITH INTEGRATED VCO - SMT
Figure 37. HMC835LP6GE with External
VCO HMC384LP4E at 2213MHz [25]
[25] 50MHz PFD with Loop Filter Type 4 is used. In order to configure HMC835LP6GE to use with external VCO, Reg 17h need to be configured to
disable the on chip VCO and VCO to PLL path while enable External Buffer, second CP link and External IO switch. Reg 17h [0:11] as 3157d. Reg
0Bh[4] =1: PFD SWAP might be needed to be selected for active loop filter. Reg 0Bh[4] = 0: For use with positive tuning slope VCO and PASSIVE loop
filter. Reg 0Bh[4] = 1: For use with a NEGATIVE slope VCO or with a ACTIVE loop filter.
[26] Loop Filter #1 is suggested to use for best integrated phase noise. It is designed for 50 MHz PD frequency, CP =2 mA in Fractional Mode.
[27] Loop Filter #2 is suggested to use for best far out phase noise. It is designed for 50 MHz PD frequency, CP =2 mA in Fractional Mode.
[28] Loop Filter #3 is suggested to use for best low frequency phase noise used as reference source. It is designed for 50 MHz PD frequency, CP =2
mA in Integer Mode.
[29] Loop Filter #4 is a example to use HMC835LP6GE as a PLL and connect with external VCO.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
12
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
PLLs WITH INTEGRATED VCO - SMT
Table 2. Pin Descriptions
13
Pin Number
Function
1
VDDCP
Description
2
BIAS
External bypass decoupling for precision bias circuits, 3.5 V
NOTE: BIAS ref voltage cannot drive an external load. Must be measured with 10 GΩ meter such as
Agilent 34410A, normal 10 MΩ DVM will read erroneously.
3
CP1
Charge Pump output 1
4
CP2
Charge Pump output 2
Power Supply for charge pump analog section, 5.0V Nominal
5
RVDD
Reference supply, 3.3 V nominal.
6
XREFP
Reference Input. DC bias is generated internally. Normally AC coupled externally.
Digital supply, 3.3 V nominal
7
DVDD
8, 9, 10, 11,
12, 16, 21,
22, 23, 24
N/C
13
AUX0_SDO
Auxiliary SDO, digital output
14
AUX1_SCK
Auxiliary SCK, digital output
15
AUX2_SEN
Auxiliary SEN, digital output
No Connect
17
GND
18
LO2_P
RF Output LO2_P, positive side, used for differential or dual outputs only.
RF Output LO2_N, negative side, used in single-ended, differential, or dual output mode
19
LO2_N
20
GND
Ground
Ground
25
CHIP_EN
26
LO1_N
Chip Enable input.
RF output LO_N, negative side, used for single-ended, differential, or dual output mode
27
LO1_P
RF output LO_P, positive side, used for differential or dual outputs only.
28
VCC1
VCO analog supply 1.
VCO analog supply 2.
29
VCC2
30
VTUNE
31
SEN
Serial Port Enable (CMOS) logic input
32
SDI
Serial Port Data (CMOS) logic input
33
SCK
Serial Port Clock (CMOS) logic input
VCO varactor tuning port input.
34
LD_SDO
35
EXT_VCO_N
Lock Detect or Serial Data Output (CMOS) logic output.
External VCO negative input.
36
EXT_VCO_P
External VCO positive input.
37
VCCHF
Analog supply, 3.3 V nominal
38
VCCPS
Analog supply, Prescaler, 3.3 V nominal
39
VCCPD
Analog supply, Phase Detector, 3.3 V nominal
40
VDDLS
Analog supply, Charge Pump, 5.0 V nominal
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
Absolute Maximum Ratings
AVDD, RVDD, DVDD, VCCPD,
VCCHF, VCCPS
-0.3 V to +3.6 V
VPPCP, VDDLS, VCC1
-0.3 V to +5.5 V
VCC2
-0.3 V to +5.5 V
Operating Temperature
-40 °C to +85 °C
Storage Temperature
-65 °C to 150 °C
Maximum Junction Temperature
150 °C
Thermal Resistance (ѲJC)
(junction to case (ground paddle))
9 °C/W
Stresses above those listed under Absolute Maximum
Ratings may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device at these or any other conditions above those
indicated in the operational section of this specification
is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Reflow Soldering
Peak Temperature
260 °C
Time at Peak Temperature
40 sec
ESD Sensitivity (HBM)
Class 1B
Recommended Operating Conditions
Parameter
Condition
Min.
Typ.
Max.
Units
85
°C
Temperature
Ambient backside metal ground pad Temperature[1]
-40
Supply Voltage
AVDD, RVDD, DVDD, VCCPD, VCCHF, VCCPS
3.1
3.3
3.5
V
VPPCP, VDDLS, VCC1, VCC2,VDDCP
4.8
5
5.2
V
[1] Layout design guidlines set out in Qualification Test Report are strongly recommended with paddle at 85°C.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
14
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
PLLs WITH INTEGRATED VCO - SMT
Outline Drawing
NOTES:
1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND
SILICON IMPREGNATED.
2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY.
3. LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN.
4. DIMENSIONS ARE IN INCHES [MILLIMETERS].
5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
6. PAD BURR LENGTH SHALL BE 0.15mm MAX. PAD BURR HEIGHT SHALL BE 0.25mm
MAX.
7. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
8. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF
GROUND.
9. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
Package Marking [1]
HMC835LP6GE
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
H835
XXXX
[1] 4-Digit lot number XXXX
15
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm
impedance while the package ground leads and exposed paddle should be connected directly to the ground plane
similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from Hittite upon request.
Evaluation PCB Schematic
To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC835LP6GE from the “Search
by Part Number” pull down menu to view the product splash page.
PLLs WITH INTEGRATED VCO - SMT
Evaluation PCB
Evaluation Order Information
Item
Evaluation Kit
Contents
HMC835LP6GE Evaluation PCB
USB Interface Board
6’ USB A Male to USB B Female Cable
CD ROM (Contains User Manual, Evaluation PCB Schematic, Evaluation Software,
Hittite PLL Design Software)
Part Number
EKIT01-HMC835LP6G
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
16
HMC835LP6GE
v04.1113
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
17
Changing Evaluation Board Reference Frequency & CP Current Configuration
The evaluation board is provided with a 50 MHz on-board reference oscillator, and loop filter #1 configuration shown
in Table 1 (~161 kHz bandwidth). The default register configuration file included in the Hittite PLL Evaluation software
sets the comparison frequency to 50 MHz (R=1, ie. Reg 02h = 1).
As with all PLL’s and PLL with Integrated VCOs, modifying the comparison frequency or Charge Pump (CP) current
will result in changes to the loop dynamics and ultimately, phase noise profile. When making these changes there are
several items to keep in mind:
• CP Offset Current setting - Refer to Section 1.3.1.
• LD Configuration - Refer to Section 1.3.5.
To redesign the loop filter for a particular application, download Hittite’s PLL Design software tool by clicking on the
“Software Download” link on the HMC835LP6GE product page at www.hittite.com. Hittite PLL Design enables users
to accurately model and analyze performance of all Hittite PLLs, PLLs with Integrated VCOs, and Clock Generators.
It supports various loop filter topologies, and enables users to design custom loop filters and accurately simulate
resulting performance.
For evaluation purposes, the HMC835LP6GE evaluation board is shipped with an on-board, low cost, reasonable
noise 100 ppm, 50 MHz VCXO, enabling evaluation of most parameters including phase noise without any external
references.
Exact phase or frequency measurements require the HMC835LP6GE to use the same reference as the measuring
instrument. To accommodate this requirement, the HMC835LP6GE evaluation board includes the HMC1031MS8E; a
simple low current integer-N PLL that can lock the on-board VCXO to an external 10 MHz reference input commonly
provided by most test equipment. To lock the HMC835LP6GE to external 10 MHz reference simply connect the
external reference output to J2 input of the HMC835LP6GE evaluation board and change the HMC1031MS8E integer
divider value to 5 by changing the switch settings D1 = 1 (SW1-4 closed), and D0 = 0 (SW2-3 open), for more
information please see the HMC1031MS8E data sheet.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
Use HMC835LP6GE as PLL with external VCO Configuration
In general, in order to configure HMC835 with external VCO, Reg17h needs to be configured to disable the on chip
VCO and VCO to PLL path while enable external buffer, CP2 link and External IO switch. The recommended value for
Reg 17h is to be set as 3157d. Reg 19h[20:19] is also available to adjust the EXT VCO amp Input depending on the
external VCO RF output level.
Use HMC835LP6GE as PLL with on board external VCO
In order to demonstrate the ablity of using HMC835LP6GE as a PLL alone with external VCO, the evaluation board is
provided with a on board external VCO HMC384LP4E and Loop Filter Type 4 configuration shown in Table 1(~17 kHz
bandwidth). A 0 Ω resister on C40 and a 0.001 uF capcitor on C58 need to be soldered in order to convert the standard
HMC835LP6GE evaluation board to work with on board external VCO configuration.Jumper J4 needs to be put on for
HMC384LP4E power supply. Reg 0Bh[4] PFD invert needs to be set to 1 in order to work with on board active loop
filter. (0=For use with positive tuning slope VCO and PASSIVE loop filter. 1=For use with a NEGATIVE slope VCO or
with a ACTIVE loop filter)
Use HMC835LP6GE as PLL with off board external VCO
The evaluation board is provided with external VCO input ports (J10: EXT_VCO_P and J11: EXT_VCO_N). Prepopulated
loop filter can be modified according to external VCO characteristics.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
18
HMC835LP6GE
v04.1113
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
HMC835LP6GE Application Information
Large bandwidth (33 MHz to 4100 MHz), excellent phase noise and spurious performance, and phase noise floor (-167
dBc/Hz), coupled with a high level of integration make the HMC835LP6GE ideal for a variety of applications; as an
RF or IF stage LO.
Figure 36. HMC835LP6GE in a typical transmit chain
Figure 37. HMC835LP6GE in a typical receive chain
19
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
Figure 38. FRACTIONAL-N PLL WITH INTEGRATED VCO used as a tunable reference for HMC835LP6GE
Using the HMC835LP6GE with a tunable reference as shown in Fig 38, it is possible to drastically improve spurious
emissions performance across all frequencies. Example shown in Fig 23 Fig 24 shows that it is possible to achieve
spurious emissions as low as -95 dBc/Hz at 3 GHz. Please contact Hittite’s application support to obtain detailed
tunable reference information.
Power Supply
The HMC835LP6GE is a high performance low-noise device. In some cases phase noise and spurious performance
may be degraded by noisy power supplies. To achieve maximum performance and ensure that power supply noise
does not degrade the performance of the HMC835LP6GE it is highly recommended to use Hittite’s low noise high
PSRR (Power Supply Rejection Ratio) regulator, the HMC1060LP3E. Using the HMC1060LP3E lowers the design risk
and cost, and ensures that the performance shown in “Typical Performance Characteristics” can be achieved.
Power supply noise contribution to the PLL output phase noise can easily be modelled in the Hittite PLL Design tool.
To download Hittite’s PLL Design software tool, click on the “Software Download” link on the HMC835LP6GE product
page at www.hittite.com
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
20
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
1.0
Theory of Operation
PLLs WITH INTEGRATED VCO - SMT
The block diagram of HMC835LP6GE PLL with Integrated VCO is shown in Figure 39.
Figure 39. HMC835LP6GE PLL VCO Block Diagram
1.1
Overview
The PLL divides down the VCO output to the desired comparison frequency via the N-divider (integer value
set in Reg 03h, fractional value set in Reg 04h), compares the divided VCO signal to the divided reference
signal (reference divider set in Reg 02h) in the Phase Detector (PD), and drives the VCO tuning voltage
via the Charge Pump (CP) (configured in Reg 09h) to the VCO subsystem. Some of the additional PLL
subsystem functions include:
• Delta Sigma configuration (Reg 06h)
• Exact Frequency Mode (Configured in Reg 0Ch, Reg 06h,Reg 03h, and Reg 04h)
• Lock Detect (LD) Configuration (Reg 07h to configure LD, and Reg 0Fh to configure LD_SDO output
pin)
•
External CEN pin used as hardware enable pin.
Typically, only writes to the divider registers (integer part Reg 03h, fractional part Reg 04h,VCO Divide
Ratio part Reg 04h) are required for HMC835LP6GE output frequency changes.
Divider registers of the PLL (Reg 03h, and Reg 04h), set the fundamental frequency (2050 MHz to 4100
MHz) of the VCO. Output frequencies ranging from 33 MHz to 2050 MHz are generated by tuning to the
appropriate fundamental VCO frequency (2050 MHz to 4100 MHz) by programming N divider (Reg 03h,
and Reg 04h), and programming the output divider (divide by 1/2/4/6.../60/62, programmed in Reg 16h) in
the VCO register.
For detailed frequency tuning information and example, please see “1.3.7 Frequency Tuning” section.
21
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
1.2
VCO Subsystem
The VCO consists of a capacitor switched step tuned VCO and an output stage. In typical operation, the
VCO is programmed with the appropriate capacitor switch setting which is executed automatically by the
PLL AutoCal state machine if AutoCal is enabled (Reg 0Ah[11] = 0, see section “1.2.1 VCO Calibration” for
more information). The VCO tunes to the fundamental frequency (2050 MHz to 4100 MHz), and is locked by
the CP output from the PLL subsystem. The VCO controls the output stage of the HMC835LP6GE enabling
configuration of:
•
1.2.1
•
•
•
VCO Output divider settings configured in Reg 16h (divide by 2/4/6...60/62 to generate frequencies
from 33 MHz to 2050 MHz, or divide by 1 to generate fundamental frequencies between 2050 MHz
and 4100 MHz)
Output gain settings (Reg 16h[7:6], Reg 16h[9:8])
Single-ended or differential output operation (Reg 17h[9:8])
Always Mute (Reg 16h[5:0])
•
Mute when unlock (Reg 17h[7])
VCO Calibration
1.2.1.1 VCO Auto-Calibration (AutoCal)
The HMC835LP6GE uses a step tuned type VCO. A step tuned VCO is a VCO with a digitally selectable
capacitor bank allowing the nominal center frequency of the VCO to be adjusted or ‘stepped’ by switching
in/out VCO tank capacitors. A step tuned VCO allows the user to center the VCO on the required output
frequency while keeping the varactor tuning voltage optimized near the mid-voltage tuning point of the
HMC835LP6GE’s charge pump. This enables the PLL charge pump to tune the VCO over the full range of
operation with both a low tuning voltage and a low tuning sensitivity (kvco).
The VCO switches are normally controlled automatically by the HMC835LP6GE using the Auto-Calibration
feature. The Auto-Calibration feature is implemented in the internal state machine. It manages the selection
of the VCO sub-band (capacitor selection) when a new frequency is programmed. The VCO switches may
also be controlled directly via register Reg 15h for testing or for other special purpose operation.
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
To use a step tuned VCO in a closed loop, the VCO must be calibrated such that the HMC835LP6GE
knows which switch position on the VCO is optimum for the desired output frequency. The HMC835LP6GE
supports Auto-Calibration (AutoCal) of the step tuned VCO. The AutoCal fixes the VCO tuning voltage at
the optimum mid-point of the charge pump output, then measures the free running VCO frequency while
searching for the setting which results in the free running output frequency that is closest to the desired
phase locked frequency. This procedure results in a phase locked oscillator that locks over a narrow
voltage range on the varactor. A typical tuning curve for a step tuned VCO is shown in Fig 40.Note how
the tuning voltage stays in a narrow range over a wide range of output frequencies such as fast frequency
hopping.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
22
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
TUNE VOLTAGE AFTER CALIBRATION (V)
PLLs WITH INTEGRATED VCO - SMT
5
4
3
2
1
fmin
fmax
0
1900 2100 2300 2500 2700 2900 3100 3300 3500 3700 3900 4100 4300
VCO FREQUENCY(MHz)
Calibrated at 85C, Measured at 85C
Calibrated at 85C, Measured at -40C
Calibrated at -40C, Measured at -40C
Calibrated at -40C, Measured at 85C
Calibrated at 27C, Measured at 27C
Figure 40. Typical VCO Tuning Voltage After Calibration
The calibration is normally run automatically once for every change of frequency. This ensures optimum
selection of VCO switch settings vs. time and temperature. The user does not normally have to be concerned
about which switch setting is used for a given frequency as this is handled by the AutoCal routine. The
accuracy required in the calibration affects the amount of time required to tune the VCO. The calibration
routine searches for the best step setting that locks the VCO at the current programmed frequency, and
ensures that the VCO will stay locked and perform well over it’s full temperature range without additional
calibration, regardless of the temperature that the VCO was calibrated at.
Auto-Calibration can also be disabled allowing manual VCO tuning. Refer to section 1.2.1.6 for a description
of manual tuning.
1.2.1.2.2
Auto-reLock on Lock Detect Failure
It is possible by setting Reg 0Ah[17] to have the VCO subsystem automatically re-run the calibration
routine and re-lock itself if Lock Detect indicates an unlocked condition for any reason. With this option the
system will attempt to re-Lock only once.
1.2.1.3.3
VCO AutoCal on Frequency Change
Assuming Reg 0Ah[11]=0, the VCO calibration starts automatically whenever a frequency change is
requested. If it is desired to rerun the AutoCal routine for any reason, at the same frequency, simply rewrite
the frequency change with the same value and the AutoCal routine will execute again without changing
final frequency.
1.2.1.4.4
VCO AutoCal Time & Accuracy
The VCO frequency is counted for Tmmt, the period of a single AutoCal measurement cycle.
n
Tmmt = Txtal · R · 2
(EQ 1)
n
is set by Reg 0Ah[2:0] and results in measurement periods which are multiples of the PD
period, TxtalR.
R
is the reference path division ratio currently in use, Reg 02h
Txtal
is the period of the external reference (crystal) oscillator.
The VCO AutoCal counter will, on average, expect to register N counts, rounded down (floor) to the nearest
integer, every PD cycle.
N
23
is the ratio of the target VCO frequency, fvco, to the frequency of the PD, fpd, where N can
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
be any rational number supported by the N divider.
N = Nint + Nfrac / 2
24
(EQ 2)
The AutoCal state machine runs at the rate of the FSM clock, TFSM, where the FSM clock frequency cannot
be greater than 50 MHz.
m
TFSM = Txtal · 2
m
(EQ 3)
is 0, 2, 4 or 5 as determined by Reg 0Ah[14:13]
The expected number of VCO counts, V, is given by
n
V = floor (N · 2 )
(EQ 4)
The nominal VCO frequency measured, fvcom, is given by
n
fvcom = V · fxtal / (2 · R)
(EQ 5)
where the worst case measurement error, ferr , is:
n+1
ferr ≈ ±fpd / 2
(EQ 6)
PLLs WITH INTEGRATED VCO - SMT
N is set by the integer (Nint = Reg 03h) and fractional (Nfrac = Reg 04h) register contents
Figure 41. VCO Calibration
A 5-bit step tuned VCO, for example, nominally requires 5 measurements for calibration, worst case 6
measurements, and hence 7 VSPI data transfers of 20 clock cycles each. Total calibration time, worst
case, is given by:
n
Tcal = k128TFSM + 6TPD 2 + 7 · 20TFSM
(EQ 7)
or equivalently
n
m
Tcal = Txtal (6R · 2 + (140+(3 · 128)) · 2 )
(EQ 8)
For guaranteed hold of lock, across temperature extremes, the resolution should be better than
1/8th the frequency step caused by a VCO sub-band switch change. Better resolution settings will show no
improvement.
1.2.1.4.1.1
VCO AutoCal Example
The HMC835LP6GE must satisfy the maximum fpd limited by the two following conditions:
a. N ≥ 16 (fint), N ≥ 20.0 (ffrac), where N = f VCO/ fpd
b. fpd ≤ 100 MHz
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
24
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
PLLs WITH INTEGRATED VCO - SMT
Suppose the HMC835LP6GE output frequency is to operate at 2.01 GHz. Our example crystal frequency
is fxtal = 50 MHz, R=1, and m=0 (Fig 41), hence TFSM = 20 ns (50 MHz). Note, when using AutoCal, the
maximum AutoCal Finite State Machine (FSM) clock cannot exceed 50 MHz (see Reg 0Ah[14:13]). The
FSM clock does not affect the accuracy of the measurement, it only affects the time to produce the result.
This same clock is used to clock the 16 bit VCO serial port.
If time to change frequencies is not a concern, then one may set the calibration time for maximum accuracy,
and therefore not be concerned with measurement resolution.
Using an input crystal of 50 MHz (R=1 and fpd=50 MHz) the times and accuracies for calibration using
(EQ 6) and (EQ 8) are shown in Table 3. Where minimal tuning time is 1/8th of the VCO band spacing.
Across all VCOs, a measurement resolution better than 800 kHz will produce correct results. Setting
m = 0, n = 5, provides 781 kHz of resolution and adds 8.6 µs of AutoCal time to a normal frequency hop.
Once the AutoCal sets the final switch value, 8.64 µs after the frequency change command, the fractional
register will be loaded, and the loop will lock with a normal transient predicted by the loop dynamics. Hence
as shown in this example that AutoCal typically adds about 8.6 µs to the normal time to achieve frequency
lock. Hence, AutoCal should be used for all but the most extreme frequency hopping requirements.
Table 3. AutoCal Example with Fxtal = 50 MHz, R = 1, m = 0
Control Value
Reg0Ah[2:0]
n
2n
Tmmt
(µs)
Tcal
(µs)
Ferr Max
0
0
1
0.02
4.92
± 25 MHz
1
1
2
0.04
5.04
± 12.5 MHz
2
2
4
0.08
5.28
± 6.25 MHz
3
3
8
0.16
5.76
± 3.125 MHz
4
5
32
0.64
8.64
± 781 kHz
5
6
64
1.28
12.48
± 390 kHz
6
7
128
2.56
20.16
± 195 kHz
7
8
256
5.12
35.52
± 98 kHz
1.2.1.5 Manual VCO Calibration for Fast Frequency Hopping
If it is desirable to switch frequencies quickly it is possible to eliminate the AutoCal time by calibrating
the VCO in advance and storing the switch number vs frequency information in the host. This can be
done by initially locking the HMC835LP6GE on each desired frequency using AutoCal, then reading,
and storing the selected VCO switch settings. The VCO switch settings are available inReg 15h[8:1] after
every AutoCal operation. The host must then program the VCO switch settings directly when changing
frequencies. Manual writes to the VCO switches are executed immediately as are writes to the integer and
fractional registers when AutoCal is disabled. Hence frequency changes with manual control and AutoCal
disabled, requires a minimum of two serial port transfers to the HMC835LP6GE, once to set the VCO
switches, and once to set the PLL frequency.
If AutoCal is disabled Reg 0Ah[11]=1, the VCO will update its registers with the value written via Reg
15h[8:1] immediately.
1.2.2
Registers required for Frequency Changes in Fractional Mode
A large change of frequency, in fractional mode (Reg 06h[11]=1), may require Main Serial Port writes to:
1. The integer register intg, Reg 03h (only required if the integer part changes)
2. Manual VCO Tuning Reg 15h only required for manual control of VCO if Reg 0Ah[11]=1 (AutoCal
25
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
disabled)
3. VCO Divide Ratio and Gain Register
• Reg 16h[5:0] is required to change the VCO Output Divider value if needed.
•
Reg 16h[10:6] is required to change the Output Gain if needed.
4. The fractional register, Reg 04h. The fractional register write triggers AutoCal if Reg 0Ah[11]=0, and
is loaded into the Delta Sigma modulator automatically after AutoCal runs. If AutoCal is disabled, Reg
0Ah[11]=1, the fractional frequency change is loaded into the Delta Sigma modulator immediately
when the register is written with no adjustment to the VCO.
Small steps in frequency in fractional mode, with AutoCal enabled (Reg 0Ah[11]=0), usually only require a
single write to the fractional register. Worst case, 3 Main Serial Port transfers to the HMC835LP6GE could
be required to change frequencies in fractional mode. If the frequency step is small and the integer part of
the frequency does not change, then the integer register is not changed. In all cases, in fractional mode, it
is necessary to write to the fractional register Reg 04h for frequency changes.
1.2.3
Registers Required for Frequency Changes in Integer Mode
A change of frequency, in integer mode (Reg 06h[11]=0), requires Main Serial Port writes to:
1. VCO register
• Reg 15h only required for manual control of VCO if Reg 0Ah[11]=1 (AutoCal disabled)
• Reg 16h is required to change the VCO Output Divider value if needed
2. The integer register Reg 03h.
•
1.2.4
In integer mode, an integer register write triggers AutoCal if Reg 0Ah[11]=0, and is loaded into
the prescaler automatically after AutoCal runs. If AutoCal is disabled, Reg 0Ah[11]=1, the integer
frequency change is loaded into the prescaler immediately when written with no adjustment
to the VCO. Normally changes to the integer register cause large steps in the VCO frequency,
hence the VCO switch settings must be adjusted. AutoCal enabled is the recommended method
for integer mode frequency changes. If AutoCal is disabled (Reg 0Ah[11]=1), a prior knowledge of
the correct VCO switch setting and the corresponding adjustment to the VCO is required before
executing the integer frequency change.
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
VCO Output Mute Function
The HMC835LP6GE features an intelligent output mute function with the capability to disable the VCO
output while maintaining the PLL and VCO subsystems fully functional. The mute function is automatically
controlled by the HMC835LP6GE, and provides a number of mute control options including:
1. Always mute (Reg 16h[5:0] = 0d). This mode is used for manual mute control.
2. Automatically mute the outputs during VCO calibration (Reg 17h[7] = 1) that occurs during output
frequency changes.
This mode can be useful in eliminating any out of band emissions during freqeuncy changes, and ensuring
that the system emits only desired frequencies. It is enabled by writing Reg 17h[7] = 1. Typical isolation
when the HMC835LP6GE is muted is always better than 60 dB, and is ~ 30 dB better than disabling the
output buffers of the HMC835LP6GE via Reg 17h[5:4].
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
26
HMC835LP6GE
v04.1113
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
1.3
PLL Overview
1.3.1
Phase Detector (PD)
The Phase detector (PD) has two inputs, one from the reference path divider and one from the RF path
divider. When in lock these two inputs are at the same average frequency and are fixed at a constant
average phase offset with respect to each other. We refer to the frequency of operation of the PD as fpd.
Most formulae related to step size, delta-sigma modulation, timers etc., are functions of the operating
frequency of the PD, fpd. fpd is also referred to as the comparison frequency of the PD.
The PD compares the phase of the RF path signal with that of the reference path signal and controls the
charge pump output current as a linear function of the phase difference between the two signals. The
output current varies linearly over a full ±2π radians (±360°) of input phase difference.
1.3.1.1 Charge Pump
A simplified diagram of the charge pump is shown in Fig 42. The CP consists of 4 programmable current
sources, two controlling the CP Gain (Up Gain Reg 09h[13:7], and Down Gain Reg 09h[6:0]) and two
controlling the CP Offset, where the magnitude of the offset is set by Reg 09h [20:14], and the direction is
selected by Reg 09h [21]=1 for up and Reg 09h [22]=1 for down offset.
CP Gain is used at all times, while CP Offset is only recommended for fractional mode of operation.
Typically the CP Up and Down gain settings are set to the same value (Reg 09h[13:7] = Reg 09h[6:0]).
Figure 42. Charge Pump Gain & Offset Control
1.3.1.2.2
Charge Pump Switch
Charge pump Up and Down gains are set by Reg 09h[13:7] and Reg 09h[6:0] respectively. The current gain
of the pump in Amps/radian is equal to the gain setting of this register divided by 2π.
Typical CP gain setting is set to 2 to 2.5 mA, however lower values can also be used. Values < 1 mA may
result in degraded Phase Noise performance.
For example, if both Reg 09h[13:7] and Reg 09h[6:0] are set to ‘50d’ the output current of each pump will
be 1 mA and the phase frequency detector gain kp = 1 mA/2π radians, or 159 µA/rad.
27
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Charge Pump Phase Offset
In Integer Mode, the phase detector operates with zero offset. The divided reference and the divided
VCO arrive at the phase detector at the same time. Integer mode does not require any CP Offset current.
When operating in Integer Mode simply disable CP offset in both directions (Up and down), by writing Reg
09h[22:21] = ‘00’b.
In Fractional Mode CP linearity is of paramount importance. Any non-linearity degrades phase noise and
spurious performance. These non-linearities are eliminated by operating the PD with an average phase
offset, either positive or negative (either the reference or the VCO edge always arrives first at the PD).
In non-inverting configurations, a programmable CP offset current source is used to add DC current to the
loop filter and create the desired phase offset. Positive current causes the VCO to lead, negative current
causes the reference to lead.
The CP offset is controlled via Reg 09h[20:14]. The phase offset is scaled from 0 degrees, that is the
reference and the VCO path arrive in phase, to 360 degrees, where they arrive a full cycle late.
The recommended charge pump offset current a function of the PFD period and CP gain, and is provided
in (EQ 9). It is also plotted in Fig 43 vs. PD frequency for typical CP Gain currents.
(
)
(EQ 9)
Recommended CP Offset = min  4.3 × 10−9 × FPD × ICP ,0.25 × ICP 


where:
FPD: Comparison frequency of the Phase Detector (Hz)
ICP: is the full scale current setting (A) of the switching charge pump (set in Reg 09h[6:0], [13:7]
RECOMMENDED OFFSET CURRENT (uA)
700
CP Current = 2.5 mA
600
500
CP Current = 2 mA
400
PLLs WITH INTEGRATED VCO - SMT
1.3.1.3.3
300
200
CP Current = 1 mA
100
0
0
20
40
60
80
100
PHASE DETECTOR FREQUENCY (MHz)
Figure 43.Recommended CP offset current vs PD frequency for typical CP gain currents. Calculated using (EQ 9)
The required CP offset current should never exceed 25 % of the programmed CP current. It is recommended
to enable the Up Offset and disable the Down Offset by writing Reg 09h[22:21] = ‘10’b.
Operation with CP offset influences the configuration of the Lock Detect function. Refer to the description
of Lock Detect function in section 1.3.5.
When operating with PD frequency >=80MHz, the CP Offset current should be disabled for the frequency
change and then re-enabled after the PLL has settled. If the CP Offset current is enabled during a
frequency change it may not lock.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
28
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
1.3.1.4 Phase Detector Functions
Phase detector register Reg 0Bh allows manual access to control special phase detector features.
PLLs WITH INTEGRATED VCO - SMT
Setting Reg 0Bh[5] = 0, masks the PD up output, which prevents the charge pump from pumping up.`
Setting (Reg 0Bh[6]) = 0, masks the PD down output, which prevents the charge pump from pumping
down.
Clearing both Reg 0Bh[5] and Reg 0Bh[6] tri-states the charge pump while leaving all other functions
operating internally.
PD Force UP Reg 0Bh[9] = 1 and PD Force DN Reg 0Bh[10] = 1 allows the charge pump to be forced up
or down respectively. This will force the VCO to the ends of the tuning range which can be useful in VCO
testing.
1.3.2
Reference Input Stage
Figure 44. Reference Path Input Stage
The reference buffer provides the path from an external reference source (generally crystal based) to
the R divider, and eventually to the phase detector. The buffer has two modes of operation controlled by
Reg 08h[21]. High Gain (Reg 08h[21] = 0), recommended below 200 MHz, and High frequency (Reg 08h[21]
= 1), for 200 to 350 MHz operation. The buffer is internally DC biased, with 100 Ω internal termination. For
50 Ω match, an external 100 Ω resistor to ground should be added, followed by an AC coupling capacitor
(impedance < 1 Ω), then to the XREFP pin of the part.
At low frequencies, a relatively square reference is recommended to keep the input slew rate high. At higher
frequencies, a square or sinusoid can be used. The following table shows the recommended operating
regions for different reference frequencies. If operating outside these regions the part will normally still
operate, but with degraded reference path phase noise performance.
29
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Table 4. Reference Sensitivity Table
Slew > 0.5V/ns
Sinusoidal Input
Recommended Swing (Vpp)
Recommended Power Range (dBm)
Recommended
Min
Max
Recommended
Min
Max
< 10
YES
0.6
2.5
x
x
x
(MHz)
10
YES
0.6
2.5
x
x
x
25
YES
0.6
2.5
ok
8
15
50
YES
0.6
2.5
YES
6
15
100
YES
0.6
2.5
YES
5
15
150
ok
0.9
2.5
YES
4
12
200
ok
1.2
2.5
YES
3
8
Input referred phase noise of the PLL when operating at 50 MHz is between -148 and -150 dBc/Hz at 10
kHz offset depending upon the mode of operation. The input reference signal should be 10 dB better than
this floor to avoid deg­radation of the PLL noise contribution. It should be noted that such low levels are only
necessary if the PLL is the dominant noise contributor and these levels are required for the system goals.
1.3.3
Reference Path ’R’ Divider
The reference path “R” divider is based on a 14-bit counter and can divide input signals by values from 1
to 16,383 and is controlled via Reg 02h.
1.3.4
RF Path ’N’ Divider
The main RF path divider is capable of average divide ratios between 219-5 (524,283) and 20 in fractional
mode, and 219-1 (524,287) to 16 in integer mode.
1.3.5
Lock Detect
PLLs WITH INTEGRATED VCO - SMT
Square Input
Reference Input
Frequency
The Lock Detect (LD) function indicates that the HMC835LP6GE is indeed generating the desired
frequency. It is enabled by writing Reg 07h[11]=1. The HMC835LP6GE provides LD indicator in one of two
ways:
• As an output available on the LD_SDO pin of the HMC835LP6GE, (Configuration is required to use
the LD_SDO pin for LD purpose, for more information please see “1.8 Serial Port Open Mode” and
“1.3.5.3 Configuring LD_SDO Pin for LD Output” section).
• Or reading from Reg 12h[1], where Reg 12h[1] = 1 indicates locked and Reg 12h[1] = 0 indicates an
unlocked condition.
The device incorporates a self-calibrating or automatic ‘training’ feature to manage the LD configuration.
The simplest configuration is to use the training feature. If the training feature is not used, the user
must calculate the required configuration for reliable LD indication. Described below are details for LD
configuration with and without the training feature.
1.3.5.1 Lock Detect Configuration using Training
The HMC835LP6GE lock-detect functionality is self-calibrating. Typically the lock-detect training is only
required once on power-up, or each time the reference frequency or the R divider value (Reg 02h) is
changed.
To train the lock-detect circuitry of the HMC835LP6GE on power-up, set:
• set Reg 07h [11] = 1 to enable lock-detect counters
• set Reg 07h [14] = 1 to enable the lock-detect timer
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
30
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
• set Reg 07h [20] = 1 to train the lock-detect timer
PLLs WITH INTEGRATED VCO - SMT
These bits can all be written simultaneously.
On any change of the PD frequency (via either the external reference frequency, or the R divider setting
(Reg 02h)), the lock-detect circuit should be retrained by toggling Reg 07h [20] Off and then back On.
1.3.5.2 Lock Detect Configuration without Training (Manual)
The LD circuit expects the divided VCO edge and the divided reference edge to appear at the PD within a
user specified time period (window), repeatedly. Either signal may arrive first, only the difference in arrival
times is significant. The arrival of the two edges within the designated window increments an internal
counter. Once the count reaches and exceeds a user specified value (Reg 07h[2:0]) the HMC835LP6GE
declares lock.
Failure in registering the two edges in any one window resets the counter and immediately declares an
un-locked condition. Lock is deemed to be reestablished once the counter reaches the user specified
value (Reg 07h[2:0]) again.
Optimal spectral performance in fractional mode requires CP current and CP offset current configuration
discussed in detail in section “1.3.1”.
These settings in Reg 09h impact the required LD window size in fractional mode of operation. To function,
the required lock detect window size is provided by (EQ 10).


ICP Offset ( A)
1


+ 2.66 × 10−9 ( sec ) +
 FPD ( Hz ) × ICP ( A)
FPD ( Hz ) 

LD Window ( seconds ) =
in Fractional Mode
2
1
LD Window ( seconds ) =
in Integer Mode
2 × FPD
(EQ 10)
where:
FPD: is the comparison frequency of the Phase Detector
ICP Offset : is the Charge Pump Offset Current Reg 09h[20:14]
ICP: is the full scale current setting of the switching charge pump Reg 09h[6:0], or Reg 09h[13:7]
Table 5 provides the required Reg 07h settings to appropriately program the LD window size. From Table
5, simply select the closest value in the “LD Window Size” columns to the one calculated in (EQ 10) and
program Reg 07h[9:8] and Reg 07h[7:5] accordingly.
Table 5. Typical Lock Detect Window
LD Timer Speed
Reg07[9:8]
Fastest 00
31
Lock Detect Window Size
Nominal Value (ns)
6.5
8
11
17
29
53
100
195
01
7
8.9
10
7.1
9.2
12.8
21
36
68
130
255
13.3
22
38
72
138
Slowest 11
7.6
272
10.2
15.4
26
47
88
172
338
LD Timer Divide Setting
Reg07[7:5]
000
001
010
011
100
101
110
111
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Assuming, fractional mode, with a 50 MHz PD and
• Charge Pump gain of 2 mA (Reg 09h[13:7] = 64h, Reg 09h[6:0] = 64h),
• Down Offset (Reg 09h[22:21] = ‘10’b)
• Offset current magnitude of +400 µA (Reg 09h[20:14] = 50h)
Applying (EQ 11), the required LD window size is:
LD Window ( seconds )


0.4 x10−3 ( A)
1


+ 2.66 × 10−9 ( sec ) +
6
−
3
6
 50 × 10 ( Hz ) × 2 x10 ( A)
50 × 10 ( Hz ) 
=
13.33 nsec
2
(EQ 11)
Locating the Table 5 value that is closest to the (EQ 11) result, in this case 13.3 ≈ 13.33. To set the LD
window size, simply program Reg 07h[9:8] = ‘10’b and Reg 07h[7:5] = ‘010’b according to Table 5.
There is always a good solution for the lock detect window for a given operating point. The user should
understand however that one solution does not fit all operating points. As observed from (EQ 11), If charge
pump offset or PD frequency are changed significantly then the lock detect window may need to be
adjusted.
1.3.5.4 Configuring LD_SDO Pin for LD Output
Setting Reg 0Fh[4:0]=1 will display the Lock Detect Flag on LD_SDO pin of the HMC835LP6GE. If locked,
LD_SDO will be high. As the name suggests, LD_SDO pin is multiplexed between LD and SDO (Serial
Data Out) signals. Hence LD is available on the LD_SDO pin at all times except when a serial port read
is requested, in which case the pin reverts temporarily to the Serial Data Out pin, and returns to the Lock
Detect Flag after the read is completed.
LD can be made available on LD_SDO pin at all times by writing Reg 0Fh[6] = 1. In that case the
HMC835LP6GE will not provide any read-back functionality because the SDO signal is not available.
1.3.6
PLLs WITH INTEGRATED VCO - SMT
1.3.5.3 LD Window Configuration Example
Cycle Slip Prevention (CSP)
When changing VCO frequency and the VCO is not yet locked to the reference, the instantaneous
frequencies of the two PD inputs are different, and the phase difference of the two inputs at the PD varies
rapidly over a range much greater than ±2π radians. Since the gain of the PD varies linearly with phase
up to ±2π, the gain of a conventional PD will cycle from high gain, when the phase difference approaches
a multiple of 2π, to low gain, when the phase difference is slightly larger than a multiple of 0 radians. The
output current from the charge pump will cycle from maximum to minimum even though the VCO has not
yet reached its final frequency.
The charge on the loop filter small cap may actually discharge slightly during the low gain portion of the
cycle. This can make the VCO frequency actually reverse temporarily during locking. This phenomena is
known as cycle slipping. Cycle slipping causes the pull-in rate during the locking phase to vary cyclically.
Cycle Slipping increases the time to lock to a value greater than that predicted by normal small signal
Laplace analysis.
The HMC835LP6GE PD features an ability to reduce cycle slipping during frequency tunning. The Cycle
Slip Preven­tion (CSP) feature increases the PD gain during large phase errors.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
32
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
PLLs WITH INTEGRATED VCO - SMT
1.3.7
Frequency Tuning
HMC835LP6GE VCO subsystem always operates in fundamental frequency of operation (2050 MHz to
4100 MHz). The HMC835LP6GE generates frequencies below its fundamental frequency (33 MHz to 2050
MHz) by tuning to the appropriate fundamental frequency and selecting the appropriate Output Divider
setting (divide by 2/4/6.../60/62) in Reg 16h[5:0].
The HMC835LP6GE automatically controls frequency tuning in the fundamental band of operation, for
more information see “1.2.1 VCO Calibration”.
To tune to frequencies below the fundamental frequency range (<2050 MHz) it is required to tune the
HMC835LP6GE to the appropriate fundamental frequency, then select the appropriate output divider
setting (divide by 2/4/6.../60/62) in Reg 16h[5:0].
1.3.7.1 Integer Mode
The HMC835LP6GE is capable of operating in integer mode. For Integer mode set the following registers
a. Disable the Fractional Modulator, Reg 06h[11]=0
b. Bypass the Modulator circuit, Reg 06h[7]=1
In integer mode the VCO step size is fixed to that of the PD frequency. Integer mode typically has 3 dB
lower phase noise than fractional mode for a given PD operating frequency. Integer mode, however, often
requires a lower PD frequency to meet step size requirements. The fractional mode advantage is that
higher PD frequencies can be used, hence lower phase noise can often be realized in fractional mode.
Charge Pump offset should be disabled in integer mode Reg 09h[22:14] = 0h.
1.3.7.2.2
Integer Frequency Tuning
In integer mode the digital Δ∑ modulator is shut off and the N divider (Reg 03h) may be programmed to any
integer value in the range 16 to 219-1. To run in integer mode configure Reg 06h as described, then program
the integer portion of the frequency as explained by (EQ 12), ignoring the fractional part.
a. Disable the Fractional Modulator, Reg 06h[11] = 0
b. Bypass the delta-sigma modulator Reg 06h[7] = 1
c. To tune to frequencies (<2050 MHz), select the appropriate output divider valueReg 16h[5:0].
1.3.7.3 Fractional Mode
The HMC835LP6GE is placed in fractional mode by setting the following registers:
a. Enable the Fractional Modulator, Reg 06h[11]=1
b. Connect the delta sigma modulator in circuit, Reg 06h[7]=0
1.3.7.4.4
Fractional Frequency Tuning
This is a generic example, with the goal of explaining how to program the output frequency. Actual variables
are dependant upon the reference in use.
The HMC835LP6GE in fractional mode can achieve frequencies at fractional multiples of the reference.
The frequency of the HMC835LP6GE, fvco, is given by
fvco =
fxtal
R
(Nint + Nfrac) = fint + ffrac
fout = fvco / k
33
(EQ 12)
(EQ 13)
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
fout
is the output frequency after any potential dividers.
k
is 1 for fundamental, or k = 2,4,6,…58,60,62 depending on the selected output
divider value (Reg 16h[5:0])
Nint
is the integer division ratio, Reg 03h, an integer number between 20 and
524,284
Nfrac
is the fractional part, from 0.0 to 0.99999...,Nfrac=Reg 04h/224
R
is the reference path division ratio, Reg 02h
fxtal
is the frequency of the reference oscillator input
fpd
is the PD operating frequency, fxtal /R
As an example:
fout
k2
1402.5 MHz
fvco
2,805 MHz
fxtal
= 50 MHz
R
=1
fpd
= 50 MHz
Nint
= 56
Nfrac
= 0.1
Reg 04h
= round(0.1 x 224) = round(1677721.6) = 1677722
f VCO =
50e6
1
(56 +
fout =
f VCO
2
1677722
224
) = 2805 MHz + 1.192 Hz error
= 1402.5 MHz + 0.596 Hz error
(EQ 14)
PLLs WITH INTEGRATED VCO - SMT
Where:
(EQ 15)
In this example the output frequency of 1402.5 MHz is achieved by programming the 19-bit binary value
of 56d = 38h into intg_reg in Reg 03h, and the 24-bit binary value of 1677722d = 19999Ah into frac_reg in
Reg 04h. The 0.596 Hz quantization error can be eliminated using the exact frequency mode if required.
In this example the VCO output fundamental 2805 MHz is divided by 2 (Reg 16h[5:0] = 2h) = 1402.5 MHz.
1.3.7.5.5
Exact Frequency Tuning
Due to quantization effects, the absolute frequency precision of a fractional PLL is normally limited by
the number of bits in the fractional modulator. For example, a 24 bit fractional modulator has frequency
resolution set by the phase detector (PD ) comparison rate divided by 224. The value 224 in the denominator
is sometimes referred to as the modulus. Hittite PLLs use a fixed modulus which is a binary number. In
some types of fractional PLLs the modulus is variable, which allows exact frequency steps to be achieved
with decimal step sizes. Unfortunately small steps using small modulus values results in large spurious
outputs at multiples of the modulus period (channel step size). For this reason Hittite PLLs use a large
fixed modulus. Normally, the step size is set by the size of the fixed modulus. In the case of a 50 MHz PD
rate, a modulus of 224 would result in a 2.98 Hz step resolution, or 0.0596 ppm. In some applications it is
necessary to have exact frequency steps, and even an error of 3 Hz cannot be tol­erated.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
34
HMC835LP6GE
v04.1113
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Fractional PLLs are able to generate exact frequencies (with zero frequency error) if N can be
exactly represented in binary (eg. N = 50.0,50.5,50.25,50.75 etc.). Unfortunately, some common
frequencies cannot be exactly represented. For example, Nfrac = 0.1 = 1/10 must be approximated as
round((0.1 x 224)/ 224 ) ≈ 0.100000024. At fPD = 50 MHz this translates to 1.2 Hz error. Hittite’s exact frequency
mode addresses this issue, and can eliminate quantization error by programming the channel step size to
FPD/10 in Reg 0Ch to 10 (in this example). More generally, this feature can be used whenever the desired
frequency, f VCO, can be exactly represented on a step plan where there are an integer number of steps
(<224)
across
integer-N
boundaries.
Mathematically,
this
situation
is
satisfied
if:

fPD 
24 
2 
fVCOk
=
mod  fgcd  0=
where fgcd gcd(fVCO1, fPD ) and fgcd ≥ 


(EQ 16)
Where:
gcd stands for Greatest Common Divisor
fN = maximum integer boundary frequency < f VCO1
fPD = frequency of the Phase Detector
and f VCOk are the channel step frequencies where 0 < k < 224-1, As shown in Fig 44.
Figure 45. Exact Frequency Tuning
Some fractional PLLs are able to achieve this by adjusting (shortening) the length of the Phase Accumulator
(the denominator or the modulus of the Delta-Sigma modulator) so that the Delta-Sigma modulator
phase accumulator repeats at an exact period related to the interval frequency (f VCOk - f VCO(k-1)) in Fig 44.
Consequently, the shortened accumulator results in more frequent repeating patterns and as a result often
leads to spurious emissions at multiples of the repeating pattern period, or at harmonic frequencies of
f VCOk - f VCO(k-1). For example, in some applications, these intervals might represent the spacing between
radio channels, and the spurious would occur at multiples of the channel spacing.
The Hittite method on the other hand is able to generate exact frequencies between adjacent integer-N
boundaries while still using the full 24 bit phase accumulator modulus, thus achieving exact frequency
steps with a high phase detector comparison rate, which allows Hittite PLLs to maintain excellent phase
noise and spurious performance in the Exact Frequency Mode.
1.3.7.6.6
Using Hittite Exact Frequency Mode
If the constraint in (EQ 16) is satisfied, HMC835LP6GE is able to generate signals with zero frequency error
at the desired VCO frequency. Exact Frequency Mode may be re-configured for each target frequency, or
be set-up for a fixed fgcd which applies to all channels.
35
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Configuring Exact Frequency Mode For a Particular Frequency
1. Calculate and program the integer register setting Reg 03h = NINT = floor(f VCO/fPD), where the
floor function is the rounding down to the nearest integer. Then the integer boundary frequency
fN = NINT ∙ fPD
2. Calculate and program the exact frequency register value Reg 0Ch = fPD/fgcd, where
fgcd = gcd(f VCO,fPD)
 24


3. Calculate and program the fractional register setting Reg 04h NFRAC = ceil 


is the ceiling function meaning “round up to the nearest integer.”
2
( fVCOk − fN ) 
fPD
,


where ceil
Example: To configure the HMC835LP6GE for exact frequency mode at f VCO = 2800.2 MHz where Phase
Detector (PD) rate fPD = 61.44 MHz Proceed as follows:
Check (EQ 16) to confirm that the exact frequency mode for this f VCO is possible.
 fPD
 224

=
fgcd gcd(fVCO , fPD ) and fgcd ≥ 




)
(
fgcd = gcd 2800.2 × 106 ,61.44 × 106 = 120 × 103 >
61.44 × 106
= 3.662
224
Since (EQ 16) is satisfied, the HMC835LP6GE can be configured for exact frequency mode at
f VCO = 2800.2 MHz as follows:
f
1. NINT = Reg 03h = floor 


1
VCO
=

 fPD 
2. Reg 0Ch =
 2800.2 × 106 
 45
=
=
d 2Dh
 61.44 × 106 


floor 
61.44 × 106
61.44 × 106
d C00h
=
=
= 3072
=
3
6
20000
gcd 100 × 10 ,61.44 × 10
gcd ( fVCOk +1 − fVCOk ) , fPD
fPD
(
)
)
(
3. To program Reg 04h, the closest integer-N boundary frequency fN that is less than the
desired VCO frequency f VCO must be calculated. fN = fPD ∙ NINT. Using the current example:
fN =fPD × NINT =45 × 61.44 × 106 =2764.8 MHz.
(
)
 24
 224 f

2800.2 × 106 − 2764.8 × 106 
2
VCO − fN 
=
ceil
=
=
d 938000h

 9666560

fPD
61.44 × 106








Then=
Reg04h ceil 
(
)
PLLs WITH INTEGRATED VCO - SMT
1.3.7.6.1.1
1.3.7.7.7 Hittite Exact Frequency Channel Mode
If it is desirable to have multiple, equally spaced, exact frequency channels that fall within
the same interval (ie. fN ≤ f VCOk < fN+1) where f VCOk is shown in Fig 44 and 1 ≤ k ≤ 224,
it is possible to maintain the same integer-N (Reg 03h) and exact frequency register (Reg 0Ch) settings
and only update the fractional register (Reg 04h) setting. The Exact Frequency Channel Mode is possible
if (EQ 16) is satisfied for at least two equally spaced adjacent frequency channels, i.e. the channel step
size.
To configure the HMC835LP6GE for Exact Frequency Channel Mode, initially and only at the beginning,
integer (Reg 03h) and exact frequency (Reg 0Ch) registers need to be programmed for the smallest f VCO
frequency (f VCO1 in Fig 44), as follows:
1. Calculate and program the integer register setting Reg 03h = NINT = floor(f VCO1/fPD), where f VCO1
is shown in Fig 44 and corresponds to minimum channel VCO frequency. Then the lower integer
boundary frequency is given by fN = NINT ∙ fPD.
2. Calculate and program the exact frequency register value Reg 0Ch = fPD/fgcd,
where fgcd = gcd((f VCOk+1 - f VCOk),fPD) = greatest common divisor of the desired equidistant channel
spacing and the PD frequency ((f VCOk+1 - f VCOk) and fPD).
Then, to switch between various equally spaced intervals (channels) only the fractional register (Reg 04h)
needs to be programmed to the desired VCO channel frequency f VCOk in the following manner:
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
36
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
(
)
 224 f

VCOk − fN 

fPD




PLLs WITH INTEGRATED VCO - SMT

Reg 04h = NFRAC = ceil 
where fN = floor(f VCO1/fPD), and f VCO1, as shown in Fig 44, represents
the smallest channel VCO frequency that is greater than fN.
Example: To configure the HMC835LP6GE for Exact Frequency Mode for equally spaced intervals of 100
kHz where first channel (Channel 1) = f VCO1 = 2800.200 MHz and Phase Detector (PD) rate fPD = 61.44
MHz proceed as follows:
First check
that the exact frequency mode for this f VCO1 = 2800.2 MHz (Channel 1)
and f VCO2 = 2800.2 MHz + 100 kHz = 2800.3 MHz (Channel 2) is possible.
 fPD
 224

=
fgcd1 gcd(fVCO1, fPD ) and fgcd1 ≥ 

f
 and=
fgcd 2 gcd(fVCO2 , fPD ) and fgcd 2 ≥  PD

 224


)
(
=gcd ( 2800.3 × 10 ,61.44 × 10 ) =20 × 10




61.44 × 106
= 3.662
224
6
61.44 × 10
>
=3.662
224
fgcd1 = gcd 2800.2 × 106 ,61.44 × 106 = 120 × 103 >
fgcd 2
6
6
3
If (EQ 16) is satisfied for at least two of the equally spaced interval (channel) frequencies f VCO1,f VCO2 ,f VCO3 ,...
f VCON, as it is above, Hittite Exact Frequency Channel Mode is possible for all desired channel frequencies,
and can be configured as follows:
1. Reg 03h =
2. Reg 0Ch =
6 


VCO
1  floor  2800.2 × 10=
 45
=
=
d 2Dh
 fPD 
 61.44 × 106 




f
floor 
61.44 × 106
61.44 × 106
d C00h
=
=
= 3072
=
3
6
20000
gcd 100 × 10 ,61.44 × 10
gcd ( fVCOk +1 − fVCOk ) , fPD
fPD
(
)
)
(
where (f VCOk+1 - f VCOk) is the desired channel spacing (100 kHz in this example).
3. To program Reg 04h the closest integer-N boundary frequency fN that is less than the smallest
channel VCO frequency f VCO1 must be calculated. fN = floor(f VCO1/fPD). Using the current example:
 2800.2 × 106 
 =45 × 61.44 × 106 =2764.8 MHz
 61.44 × 106 


fN =fPD × floor 
Then
 224 f
( VCO1 − fN )  for channel 1 where f

Reg 04h ceil
=
=
VCO1 2800.2 MHz


f


PD


 24
2800.2 × 106 − 2764.8 × 106 
2
d 938000h
= ceil 
=
=
 9666560
61.44 × 106




)
(
4. To change from channel 1 (f VCO1 = 2800.2 MHz) to channel 2 (f VCO2 = 2800.3 MHz), only
Reg 04h needs to be programmed, as long as all of the desired exact frequencies f VCOk (Fig 44) fall
between the same integer-N boundaries (fN < f VCOk < fN+1). In that case
(
)
 24
2800.3 × 106 − 2764.8 × 106 
2
=
=
d 93EAABh
 9693867
61.44 × 106




Reg 04h = ceil 
37
, and so on.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Seed Register
The start phase of the fractional modulator digital phase accumulator (DPA) may be set to any desired
phase relative to the reference frequency, The phase is programmed in Reg 1Ah, and Exact Frequency
Mode is required. Phase = 2π x Reg1Ah/(224) via the seed register Reg 1Ah[23:0]. The HMC835LP6GE
will automatically reload the start phase (seed value) into the DPA every time a new fractional frequency is
selected. Certain zero or binary seed values may cause spurious energy correlation at specific frequencies.
For most cases a random, or non zero, non-binary start seed is recommended.
1.4
Soft Reset & Power-On Reset
The HMC835LP6GE features a hardware Power on Reset (POR). All chip registers will be reset to default
states approximately 250 µs after power up.
The PLL subsystem SPI registers may also be soft reset by an SPI write to register Reg 00h.
1.5
Power Down Mode
Power down the HMC835LP6GE by pulling CEN pin (pin 17) low (assuming no SPI overrides(Reg
01h[0]=1)). This will result in all analog functions and internal clocks disabled. Current consumption will
typically drop below 10 µA in Power Down state. The serial port will still respond to normal communication
in Power Down mode.
It is possible to ignore the CEN pin, by setting Reg 01h[0]=0. Control of Power Down Mode then comes
from the serial port register Reg 01h[1].
It is also possible to leave various blocks on when in Power Down (see Reg 01h), including:
a. Internal Bias Reference Sources Reg 01h[2]
b. PD Block
Reg 01h[3]
c. CP Block Reg 01h[4]
d. Reference Path Buffer Reg 01h[5]
e. VCO Path buffer Reg 01h[6]
f. Digital I/O Test pads Reg 01h[7]
PLLs WITH INTEGRATED VCO - SMT
1.3.8
To mute the output but leave the PLL and VCO locked please refer to 1.2.4 section.
1.6
General Purpose Output (GPO) Pin
The PLL shares the LD_SDO (Lock-Detect/Serial Data Out) pin to perform various functions. While the
pin is most commonly used to read back registers from chip via the SPI, it is also capable of exporting a
variety of signals and real time test waveforms (including Lock Detect). It is driven by a tri-state CMOS
driver with ~200 Ω Rout. It has logic associated with it to dynamically select whether the driver is enabled,
and to decide which data to export from the chip.
In its default configuration, after power-on-reset, the output driver is disabled, and only drives during
appropriately addressed SPI reads. This allows it to share the output with other devices on the same bus.
The pin driver is enabled if the chip is addressed - ie. The last 3 bits of SPI cycle = ‘000’b before the
rising edge of SEN. If SEN rises before SCK has clocked in an ‘invalid’ (non-zero) chip -address, the
HMC835LP6GE will start to drive the bus.
The FRACTIONAL-N PLL WITH INTEGRATED VCO will naturally switch away from the GPO data and
export the SDO during an SPI read. To prevent this automatic data selection, and always select the GPO
signal, set “Prevent AutoMux of SDO” (Reg 0Fh[6] = 1). The phase noise performance at this output is
poor and uncharacterized. The GPO output should not be toggling during normal operation because it may
degrade the spectral performance.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
38
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
PLLs WITH INTEGRATED VCO - SMT
Note that there are additional controls available, which may be helpful if sharing the bus with other devices:
•
To disable the driver completely, set Reg 08h[5] = 0 (it takes precedence over all else).
•
To disable either the pull-up or pull-down sections of the driver, Reg 0Fh[8] = 1 or Reg 0Fh[9] = 1
respectively.
Example Scenarios:
•
Drive SDO during reads, tri-state otherwise (to allow bus-sharing)
• No action required.
•
Drive SDO during reads, Lock Detect otherwise
• Set GPO Select Reg 0Fh [4:0] = ‘00001’b (which is default)
• Set “Prevent GPO driver disable” (Reg 0Fh[7] = 1)
•
Always drive Lock Detect
• Set “ Prevent AutoMux of SDO” Reg 0Fh[6] = 1
• Set GPO Select Reg 0Fh[4:0]= 00001 (which is default)
• Set “Prevent GPO driver disable” (Reg 0Fh[7] = 1))
The signals available on the GPO are selected in Reg 0Fh[4:0].
1.7
Chip Identification
The chip id information may be read by reading the content of read only register, chip_ID in Reg 00h.
For HMC835LP6GE, chip id is C7701Ah.
1.8
SERIAL PORT Overview
The SPI protocol has the following general features:
a. 3-bit chip address , enable the use of up to 8 devices connected to the serial bus
b. Simultaneous Write/Read during the SPI cycle
c. 5-bit address space
d. 3 wire for Write Only capability, 4 wire for Read/Write capability
Typical serial port operation can be run with SCLK at speeds up to 50 MHz.
1.8.1
Serial Port WRITE Operation
AVDD = DVDD = 3V, AGND = DGND = 0V
Table 6. SPI WRITE Timing Characteristics
Parameter
Conditions
t1
SDI setup time to SCLK Rising Edge
t2
t3
Min.
Typ.
Max
Units
3
ns
SCLK Rising Edge to SDI hold time
3
ns
SEN low duration
10
ns
t4
SEN high duration
10
ns
t5
SCLK 32 Rising Edge to SEN Rising Edge
10
ns
t6
Recovery Time
10
Max Serial port Clock Speed
ns
50
MHz
A typical WRITE cycle is shown in Fig 45.
a. The Master (host) places 24-bit data, d23:d0, MSB first, on SDI on the first 24 falling edges of SCLK.
b. the slave (HMC835LP6GE) shifts in data on SDI on the first 24 rising edges of SCLK
39
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
d. Slave shifts the register bits on the next 5 rising edges of SCLK (25-29).
e. Master places 3-bit chip address, a2:a0, MSB first, on the next 3 falling edges of SCLK (30-32). Hittite
reserves chip address a2:a0 = 000 for HMC835LP6GE.
f. Slave shifts the chip address bits on the next 3 rising edges of SCLK (30-32).
g. Master asserts SEN after the 32nd rising edge of SCLK.
h. Slave registers the SDI data on the rising edge of SEN.
i. Master clears SEN to complete the WRITE cycle.
Figure 46. Serial Port Timing Diagram - WRITE
1.8.2
Serial Port READ Operation
A typical READ cycle is shown in Fig 46.
PLLs WITH INTEGRATED VCO - SMT
c. Master places 5-bit register address to be written to, r4:r0, MSB first, on the next 5 falling edges of SCLK
(25-29)
In general, the LD_SDO line is always active during the WRITE cycle. During any SPI cycle LD_SDO will
contain the data from the current address written in Reg 00h[4:0]. If Reg 00h[4:0] is not changed then the
same data will always be present on LD_SDO when an Open Mode cycle is in progress. If it is desired to
READ from a specific address, it is necessary in the first SPI cycle to write the desired address to Reg
00h[4:0], then in the next SPI cycle the desired data will be available on LD_SDO.
An example of the two cycle procedure to read from any address follows:
a. The Master (host), on the first 24 falling edges of SCLK places 24-bit data, d23:d0, MSB first, on SDI
as shown in Fig 46. d23:d5 should be set to zero. d4:d0 = address of the register to be READ on the
next cycle.
b. the slave (HMC835LP6GE) shifts in data on SDI on the first 24 rising edges of SCK
c. Master places 5-bit register address , r4:r0, (the READ ADDRESS register), MSB first, on the next 5
falling edges of SCK (25-29). r4:r0=00000.
d. Slave shifts the register bits on the next 5 rising edges of SCK (25-29).
e. Master places 3-bit chip address, a2:a0, MSB first, on the next 3 falling edges of SCK (30-32). Chip
address is always ‘000’b.
f. Slave shifts the chip address bits on the next 3 rising edges of SCK (30-32).
g. Master asserts SEN after the 32nd rising edge of SCK.
h. Slave registers the SDI data on the rising edge of SEN.
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
40
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
PLLs WITH INTEGRATED VCO - SMT
i. Master clears SEN to complete the the address transfer of the two part READ cycle.
41
j. If one does not wish to write data to the chip during the second cycle , then it is recommended to
simply rewrite the same contents on SDI to Register zero on the READ back part of the cycle.
k. Master places the same SDI data as the previous cycle on the next 32 falling edges of SCK.
l. Slave (HMC835LP6GE) shifts the SDI data on the next 32 rising edges of SCK. On these same
edges, the slave places the desired read data (ie. data from the address specified in Reg 00h[4:0] of
the first cycle) on LD_SDO which automatically switches to SDO mode from LD mode, disabling the
LD output.
m. Master asserts SEN after the 32nd rising edge of SCK to complete the cycle and revert back to Lock
Detect on LD_SDO.
Table 7. SPI Read Timing Characteristics
Parameter
Conditions
Min.
Typ.
Max
Units
t1
SDI setup time to SCK Rising Edge
3
ns
t2
SCK Rising Edge to SDI hold time
3
ns
t3
SEN low duration
10
ns
t4
SEN high duration
10
t5
SCK Rising Edge to SDO time
t6
Recovery TIme
10
ns
t7
SCK 32 Rising Edge to SEN Rising Edge
10
ns
ns
8.2ns+0.2ns/pF
ns
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Figure 47. Serial Port Timing Diagram - READ
For more information on using the GPO pin while in SPI Mode please see section 1.8 Serial Port Overview
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
42
HMC835LP6GE
v04.1113
PLLs WITH INTEGRATED VCO - SMT
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
2.0
PLL Register Map
2.1
Reg 00h ID Register (Read Only) DEFAULT C7701A h
Bit
Type
[23:0]
RO
2.2
Name
chip_ID
Bit
Type
WO
Read Address
[5]
WO
[23:6]
WO
Bit
[0]
Default
24
C7701A
Description
Chip ID Number
Reg 00h Open Mode Read Address/RST Strobe Register (Write Only)
[4:0]
2.3
Width
Name
Width
Default
5
-
(WRITE ONLY) Read Address for next cycle
Description
Soft Reset
1
-
(WRITE ONLY) Soft Reset - (set to 0 during operation)
Not Defined
18
-
Not Defined (set to write 0h)
Reg 01h Chip Enable Register DEFAULT 3h
Type
R/W
Name
Chip Enable Pin Select
Width
1
Default
1
Description
1 = Chip enable via CHIP_EN pin, Reg 01h[0]=1 and
CHIP_EN pin low places the HMC835LP6GE in Power
Down Mode
0 = Chip enable via SPI - Reg 01h[0] = 0, CHIP_EN pin
ignored (see Power Down Mode description for more
details)
[1]
R/W
SPI Chip Enable
1
1
Controls Chip Enable (Power Down) if Reg 01h[0] =0
Reg 01h[0]=0 and Reg 01h[1]=1 - chip is enabled, CHIP_EN
pin don’t care
Reg 01h[0]=0 and Reg 01h[1]=0 - chip disabled, CHIP_EN
pin don’t care
(see Power Down Mode description for more information)
[2]
R/W
Keep Bias On
1
0
keeps internal bias generators on, ignores Chip enable
control
[3]
R/W
Keep PFD Pn
1
0
keeps PFD circuit on, ignores Chip enable control
[4]
R/W
Keep CP On
1
0
keeps Charge Pump on, ignores Chip enable control
[5]
R/W
Keep Reference Buffer ON
1
0
keeps Reference buffer block on, ignores Chip enable
control
[6]
R/W
Keep VCO Buffer ON
1
0
keeps VCO divider buffer on, ignores Chip enable control
[7]
R/W
Keep GPO Driver ON
1
0
keeps GPO output Driver ON, ignores Chip enable control
[9:8]
R/W
Reserved
2
0
Reserved
[23:10]
R/W
Spare
14
0
Don’t Care
2.4
Bit
Reg 02h REFDIV Register DEFAULT 1h
Type
Name
Width
Default
Description
[13:0]
R/W
rdiv
14
1
Reference Divider ’R’ Value (EQ 8)
min 1
max max 214-1 = 3FFFh = 16383d
[23:14]
R/W
Spare
10
0
Don’t Care
2.5
Bit
Reg 03h Frequency Register - Integer Part DEFAULT 19h
Type
Name
Width
Default
Description
Divider Integer part, used in all modes, see (EQ 10)
[18:0]
R/W
Integer Setting
19
25d
19h
Fractional Mode
min 20d
max 219 - 4 = 7FFFCh = 524,284d
Integer Mode
min 16d
max 219-1 = 7FFFFh = 524,287d
[23:19]
43
R/W
Spare
5
0
Don’t Care
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Bit
[23:0]
Reg 04h Frequency Register - Fractional Part DEFAULT 0h
Type
R/W
Name
Fractional Setting
Width
Default
24
0
Description
Divider Fractional part (24 bit unsigned) see Fractional Frequency
Tuning
Fractional Division Value = Reg4[23:0]/2^24
Used in Fractional Mode only
min 0
max 224-1 = FFFFFFh = 16,777,215d
2.7
Reg 05h Reserved DEFAULT 0h
Bit
Type
[23:0]
RO
2.8
Width
Default
24
0
Description
Reserved
Reg 06h Delta Sigma Modulator Register DEFAULT 30F0Ah
BIT
TYPE
[1:0]
R/W
[3:2]
Name
Reserved
R/W
NAME
Reserved
DSM Order
Width
Default
2
2
Reserved, don’t care
2
Select the Delta Sigma Modulator Type
0: 1st order
1: 2nd Order
2: 3rd Order - Recommended
3: Reserved
2
DESCRIPTION
0: Normal SPI Load - all register load on rising edge of SEN
1: Synchronous SPI - registers Reg 03h, Reg 04h , Reg 1Ah, Reg
0Ch wait to load synchronously on the next internal clock cycle.
Normally (When this bit is 0) SPI writes into the internal state
machines/counters happen asynchronously relative to the internal
clocks. This can create freq/phase disturbances if writing register
3, 4, 1A or 0C. When this bit is enabled, the internal SPI registers
are loaded synchronously with the internal clock. This means
that the data in the SPI shifter should be held constant for at least
2 PFD clock periods after SEN is asserted to allow this retiming to
happen cleanly.
[4]
R/W
Synchronous SPI Mode
1
0
[5]
R/W
Exact Frequency Mode
Enable
1
0
1: Exact Frequency Mode Enabled
0: Exact Frequency Mode Disabled
[6]
R/W
Reserved
1
0
Reserved
[7]
R/W
Fractional Bypass
1
0
PLLs WITH INTEGRATED VCO - SMT
2.6
0: Use Modulator, Required for Fractional Mode,
1: Bypass Modulator, Required for Integer Mode
Note: When enabled fractional modulator output is ignored, but
fractional modulator continues to be clocked if Reg 06h[11] =1.
This feature can be used to test the isolation of the digital fractional modulator from the VCO output in integer mode.
1: loads the modulator seed (start phase) whenever the fractional
register (Reg 04h) is written
[8]
R/W
Autoseed EN
1
1
[10:9]
R/W
Reserved
2
3
Reserved
[11]
R/W
Delta Sigma Modulator
Enable
1
1
0: Disable DSM, used for Integer Mode
1: Enable DSM Core, required for Fractional Mode
[22:12]
R/W
Reserved
11
48d
30h
Reserved
[23]
R/W
Spare
1
0
Don’t Care
0: when fractional register (Reg 04h) write changes frequency,
modulator starts at previous value (phase)
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
44
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
2.9
PLLs WITH INTEGRATED VCO - SMT
Bit
Reg 07h Lock Detect Register Check DEFAULT 200844h
Type
Name
Width
[2:0]
R/W
lkd_wincnt_max
3
Default
Description
4
lock detect window
sets the number of consecutive counts of divided VCO that
must land inside the Lock Detect Window to declare LOCK
0: 5
1: 32
2: 96
3: 256
4: 512
5: 2048
6: 8192
7: 65535
[4:3]
R/W
Reserved
2
00
Program 00
[7:5]
R/W
LD Timer Divide Setting
3
100
Only used with Manual LD Mode. See Table 5
[9:8]
R/W
LD Timer Speed
2
00
Only used with Manual LD Mode. See Table 5
[10]
R/W
Reserved
1
0
Program 0
[11]
R/W
LD Enable
1
1
0: LD disable
1: LD enable
[13:12]
R/W
Reserved
2
00
Program 00
[14]
R/W
LD Mode
1
0
0: Manual LD Mode
1: Automatic Training Mode
[15]
R/W
CSP Enable
1
0
0: Disabled
1: Enabled
[18:16]
R/W
Reserved
3
000
[19]
R/W
Reserved
1
0
Program 000
Program 0
0 to 1 transition triggers the training. Lock Detect Training
is only required after changing Phase Detector frequency.
[20]
R/W
Lock Detect Training
9
0
[21]
R/W
Reserved
1
1
Program 1
[23:22]
R/W
Spare
2
0
Don’t Care
2.10
After changing PD frequency a toggle Reg 07h[20] from 0
to 1 retrains the Lock Detect.
Reg 08h Analog EN Register Check DEFAULT 1BFFFh
Bit
Type
[4:0]
R/W
Name
Reserved
Width
Default
5
1Fh
Description
Reserved
0 - Pin LD_SDO disabled (Hi Z)
[5]
R/W
LD_SDO Driver Enable
1
1d
1 - and RegFh[7]=1 , Pin LD_SDO is always driven. This is
required for use as a GPO port
1 - and RegFh[7]=0 LD_SPI is off if the last Rx chip
address is not equal to ‘000’b, allowing a shared SPI with
other compatible parts
45
[9:6]
R/W
Reserved
4
Fh
Reserved
[10]
R/W
VCO Buffer and Prescaler
Bias Enable
1
1d
0: VCO Prescaler Bias Disable
1: VCO Prescaler Bias Enable
Only applies to External VCO
[20:11]
R/W
Reserved
10
37h
[21]
R/W
High Frequency Reference
1
0
Program to 1 for XTAL > 200 MHz, 0 otherwise
[22]
R/W
SDO Output Level
1
0
Output Logic Level on LD/SDO pin
0: 1.8 V Logic Levels
1: DVDD3V Logic Level
[23]
R/W
Reserved
1
0
Reserved
Reserved
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Bit
[6:0]
[13:7]
Reg 09h Charge Pump Register 547264h
Type
R/W
R/W
Name
CP DN Gain
Width
7
CP UP Gain
7
Default
Description
100d
64h
Charge Pump DN Gain Control 20 µA√step
Affects fractional phase noise and lock detect settings
0d = 0 µA
1d = 20 µA
2d = 40 µA
...
127d = 2.54mA
Default 2mA
100d
64h
Charge Pump UP Gain Control 20 µA per step
Affects fractional phase noise and lock detect settings
0d = 0 µA
1d = 20 µA
2d = 40 µA
...
127d = 2.54mA
Default 2mA
[20:14]
R/W
Offset Magnitude
7
81d
Charge Pump Offset Control 5 µA/step
Affects fractional phase noise and lock detect settings
0d = 0 µA
1d = 5 µA
2d = 10 µA
...
127d = 635 µA
Default 405µA
[21]
R/W
Offset UP enable
1
0
Sets Direction of Reg 09h[20:14] Up, 0- UP Offset Off
[22]
R/W
Offset DN enable
1
1
Sets Direction of Reg 09h[20:14] Down, 0- DN Offset Off
[23]
R/W
HiK charge pump Mode
1
0
Only recommended with external VCOs and Active Loop
Filters. When enabled the HMC835LP6GE increases CP
current by 3 mA, thereby improving phase noise performance, and increasing loop bandwidth
2.12
Bit
Reg 0Ah VCO AutoCal Configuration Register DEFAULT 2046h
Type
Name
Width
Default
Description
[2:0]
R/W
Vtune Resolution
3
6d
Used by internlan AutoCal state machine
R Divider Cycles
0-1
1-2
2-4
3-8
4 - 32
5 - 64
6 - 128
7 - 256
Ref div cycles for frequency measurement. Measurement
should last > 4 µsec.
Note: 1 does not work if R divider = 1.
[10:3]
R/W
Reserved
8
8d
Reserved
[11]
R/W
AutoCal Disable
1
0
0 = AutoCal Enabled
1 = AutoCal disabled
[12]
R/W
Reserved
1
0
Reserved
[14:13]
R/W
FSM/VSPI Clock Select
2
1
Set the AutoCal FSM and VSPI Clock (50 MHz maximum)
0: Input Crystal Reference
1: Input Crystal Reference/4
2: Input Crystal Reference/16
3: Input Crystal Reference/32
[16:15]
R/W
Reserved
2
0
Reserved
[17]
R/W
Reserved
1
0
Reserved
[23:18]
R/W
Reserved
5
0
Reserved
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
PLLs WITH INTEGRATED VCO - SMT
2.11
46
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
PLLs WITH INTEGRATED VCO - SMT
2.13
47
Reg 0Bh PD/CP Register DEFAULT 7C021h
BIT
TYPE
NAME
Width
Default
[3:0]
R/W
Reserved
4
1
Reserved
DESCRIPTION
PD Phase Select
1
0
Inverts the PD polarity (program to 0)
0- Use with a positive tuning slope VCO and Passive Loop Filter
(default when using internal VCO)
1- Use with a Negative Slope VCO or with an inverting Active Loop
Filter with a Positive Slope VCO (Only recommended when using an
External VCO, and an active loop filter)
R/W
PD Up Output Enable
1
1
Enables the PD UP output, see also Reg 0Bh[9]
R/W
PD Down Output Enable
1
1
Enables the PD DN output, see also Reg 0Bh[10]
[4]
R/W
[5]
[6]
[8:7]
R/W
Reserved
2
0
Reserved, Program to 0d.
[9]
R/W
Force CP UP
1
0
Forces CP UP output on if CP is not forced down - Use for Test only
[10]
R/W
Force CP DN
1
0
Forces CP DN output on if CP is not forced up - Use for Test only
[11]
R/W
Force CP Mid Rail
1
0
Force CP MId Rail - Use for Test only (if Force CP UP or Force CP
DN are enabled they have precedence)
[23:12]
R/W
Reserved
12
7Ch
2.14
BIT
[23:0]
Reserved
Reg 0Ch Exact Frequency Register DEFAULT 0h
TYPE
R/W
NAME
Number of Channels per Fpd
Width
24
Default
0
DESCRIPTION
Comparison Frequency divided by the correction rate. Must be an
integer. Frequencies at integer multiples of the correction rate will
have zero frequency error.
0: Disabled
1: Invalid
≥ 2 valid
max 224-1 = FFFFFFh = 16,777,215d
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
BIT
Reg 0Fh GPO Register DEFAULT 1h
TYPE
NAME
Width
Default
DESCRIPTION
Select signal to be output to SDO pin when enabled
DEFAULT LOCK DETECT
0: Data from Reg0F[5]
1: Lock Detect Output
2. Lock Detect Trigger
3: Lock Detect Window Output
4: Ring Osc Test
5. Pullup Hard from CSP
6. PullDN hard from CSP
7. Reserved
8: Reference Buffer Output
9: Ref Divider Output
10: VCO divider Output
11. Modulator Clock from VCO divider
12. Auxiliary Clock
13. Aux SPI Clock
14. Aux SPI Enable
15. Aux SPI Data Out
16. PD DN
17. PD UP
18. SD3 Clock Delay
19. SD3 Core Clock
20. AutoStrobe Integer Write
21. Autostrobe Frac Write
22. Autostrobe Aux SPI
23. SPI Latch Enable
24. VCO Divider Sync Reset
25. Seed Load Strobe
26.-29 Not Used
30. SPI Output Buffer En
31. Soft RSTB
Note: Only the default condition is tested during production.
[4:0]
R/W
GPO
5
1
[5]
R/W
GPO Test Data
1
0
1 - GPO Test Data when GPO_Select = 0
[6]
R/W
Prevent Automux SDO
1
0
1- Outputs GPO data only
0- Automuxes between SDO and GPO data
[7]
R/W
Prevent Auto tri-state SDO
1
0
Keep LD_SDO enabled, despite Rx chip address
[8]
R/W
Reserved
1
0
Reserved
[9]
R/W
Reserved
1
0
Reserved
[23:10]
R/W
Reserved
14
0
Reserved
2.16
PLLs WITH INTEGRATED VCO - SMT
2.15
Reg 10h Tuning Register (Read Only) DEFAULT 80h
BIT
TYPE
NAME
Width
Default
DESCRIPTION
[7:0]
R
VCO Tune Curve
8
0
VCO selection resulting from AutoCalibration.
0- maximum frequency
‘1111 1111’b- minimum frequency
[8]
R
VCO Tuning Busy
1
1
Indicates if the VCO tuning is in process
1- Busy
0- Not Busy
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
48
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
2.17
PLLs WITH INTEGRATED VCO - SMT
BIT
49
Reg 11h SAR Register (Read Only)
TYPE
NAME
Width
Default
219 -
DESCRIPTION
[18:0]
R
SAR Error Magnitude Count
19
1d
7FFFFh
[19]
R
SAR Error Sign
1
0
SAR Error Sign
0: positive
1: negative
[23:20]
R
Reserved
4
0
Reserved
2.18
SAR Error Magnitude Count
Reg 12h GPO/LD Register (Read Only)
BIT
TYPE
NAME
Width
Default
[0]
R
GPO Out
1
0
GPO Output
[1]
R
Lock Detect Out
1
0
Lock Detect Output
[23:2]
R
Reserved
22
7h
Reserved. May return different values after lock detect training
2.19
DESCRIPTION
Reg 13h BIST Register (Read Only)
BIT
TYPE
NAME
Width
Default
[16:0]
R
Reserved
16
4697d
1259h
DESCRIPTION
Reserved
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Reg 14h Auxiliary SPI Register DEFAULT 220h
BIT
TYPE
NAME
Width
Default
DESCRIPTION
[0]
R/W
Aux SPI Mode
1
0
[3:1]
R/W
Aux GPO Values
3
0
3 Output values can be set indivually when Reg 14h[0] = 1
[4]
R/W
Aux GPO 3.3 V
1
0
0- 1.8 V output out of the Auxiliary GPO pins
1- 3.3 V output out of the Auxiliary GPO pins
[8:5]
R/W
Reserved
4
1
Reserved
1- Use the 3 outputs as an SPI port
0- Use the 3 outputs as a static GPO port along with Reg 14h[3:1]
When set, CHIP_EN pin is used as a trigger for phase
synchronization. Can be used to synchronize multiple
[9]
[11:10]
R/W
R/W
Phase Sync
Aux SPI GPO Output
1
2
1
HMC835LP6GE, or, along with the Reg 1Ah value to phase step the
output.
(Exact Frequency Mode must be enabled)
0
Option to send GPO multiplexed data (eg. Lock Detect) to one of the
auxiliary outputs
0- None
1 - to [0]
2 - to [1]
3 - to [2]
[13:12]
R/W
Aux SPI Outputs
2
0
When the chip is disabled, the Aux SPI Outputs:
0 - Hi Z
1 - Continue driving
2 - Drive high
3 - Drive low
[23:14]
R/W
Reserved
10
0
Reserved
2.21
Reg 15h Manual VCO Config Register DEFAULT F48A0h
BIT
TYPE
NAME
Width
Default
DESCRIPTION
[0]
R/W
Vtune Preset Enable
1
0
[5:1]
R/W
Capacitor Switch Setting
5
16d
10h
[8:6]
R/W
Manual VCO Selection
3
2
selects the VCO core sub-band
[9]
R/W
Manual VCO Tune Enable
1
0
1-Manual VCO tuning enabled. Bits[8:0] are active for manual VCO
tuning.
0-Manual VCO tuning disabled. Bits[8:0] are ignored (under the
control of VCO Auto-calibration state machine)
[15:10]
R/W
Reserved
6
18d
12h
[16]
R/W
Enable Auto-Scale CP current
1
1
1 - Automatically scale CP current based on VCO frequency and
capacitor setting
0- Don’t scale CP current
[19:17]
R/W
Reserved
3
7d
Reserved
[23:20]
R/W
Spare
4
0
Don’t Care
1-Vtune Preset enabled (for manual VCO)
0-Vtune Preset controlled by VCO Auto-calibration state machine
PLLs WITH INTEGRATED VCO - SMT
2.20
capacitor switch setting
Reserved
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
50
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
2.22
PLLs WITH INTEGRATED VCO - SMT
BIT
NAME
Width
Default
DESCRIPTION
[5:0]
R/W
RF Divide Ratio
6
1
0 - Mute, VCO and PLL buffer On, RF output stages Off
1 - Fo
2 - Fo/2
3 - invalid, defaults to 2
4 - Fo/4
5 - invalid, defaults to 4
6 - Fo/6
...
60 - Fo/60
61 - invalid, defaults to 60
62 - Fo/62
> 62 - invalid, defaults to 62
[7:6]
R/W
LO Output Buffer Gain
Control
2
3
3 - Max Gain
2 - Max Gain - 3 dB
1 - Max Gain - 6 dB
0 - Max Gain - 9 dB
[9:8]
R/W
LO2 Output Buffer gain
Control
2
2
3 - Max Gain
2 - Max Gain - 3 dB
1 - Max Gain - 6 dB
0 - Max Gain - 9 dB
[10]
R/W
Divider Output Stage Gain
Control
1
1
1 - Max Gain
0 - Max Gain - 3 dB
[23:11]
R/W
Spare
13
0
Don’t Care
2.23
Reg 17h Modes Register DEFAULT 1ABh (See Figure 39)
BIT
TYPE
NAME
Width
Default
[0]
R/W
VCO SubSys Master Enable
1
1
[1]
R/W
VCO Enable
1
1
[2]
R/W
External VCO Buffer Enable
1
0
External VCO Buffer to output stage enable. Only used when locking
an external VCO.
[3]
R/W
PLL Buffer Enable
1
1
PLL Buffer Enable. Used when using an internal VCO.
DESCRIPTION
Master enable for the entire VCO Subsystem
1 - Enabled (Chip Enable required)
0 - Disabled
[4]
R/W
LO1 Output Buffer Enable
1
0
Enables LO1 (LO_P & LO_N pins) output buffer.
[5]
R/W
LO2 Output Buffer Enable
1
1
Enables the LO2 (LO2_N & LO2_P pins) output buffer
[6]
R/W
External Input Enable
1
0
Enables External VCO input
[7]
R/W
Pre Lock Mute Enable
1
1
Mute both output buffers until the PLL is locked
R/W
LO1 Output Single-Ended
Enable
1
Enables Single-Ended output mode for LO output
1- Single-ended mode, LO_N pin is enabled, and LO_P pin is
disabled
0- Differential mode, both LO_N and LO_P pins enabled
Please note that single-ended output is only available on LO_N pin.
[8]
51
Reg 16h Gain Divider Register DEFAULT 6C1h
TYPE
1
[9]
R/W
LO2 Output Single-Ended
Enable
1
0
Enables Single-Ended output mode for LO2 output
1- Single-ended mode, LO2_P pin is enabled, and LO2_N pin is
disabled
0- Differential mode, both LO2_N and LO2_P pins enabled
Please note that single-ended output is only available on LO2_N pin.
[10]
R/W
Reserved
1
0
Reserved
[11]
R/W
Charge Pump Output Select
1
0
Connects CP to CP1 or CP2 output.
0: CP1
1: CP2
[23:12]
R/W
Spare
12
0
Don’t Care
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC835LP6GE
v04.1113
FRACTIONAL-N PLL WITH INTEGRATED VCO
33 - 4100 MHz
Reg 18h Bias Register DEFAULT 54C1h
BIT
TYPE
NAME
Width
Default
[18:0]
R/W
Reserved
19
21697d
54C1h
[20:19]
R/W
External Input Buffer Bias
2
00
[23:21]
R/W
Spare
3
0
DESCRIPTION
Program to 54C3h
External input buffer bias setting.
>=1.5GHz program 11
<1.5GHz program 10
2.25
Reg 19h Cals Register DEFAULT AAAh
BIT
TYPE
NAME
Width
Default
[23:0]
R/W
Reserved
24
2730d
AAAh
2.26
BIT
[23:0]
Don’t Care
DESCRIPTION
Reserved. Program to AB2h.
Reg 1Ah Seed Register DEFAULT B29D0Bh
TYPE
R/W
NAME
Delta Sigma Modulator
Seed
Width
24
Default
DESCRIPTION
11705611d
B29D0Bh
Used to program output phase relative to the reference frequency.
(Exact Frequency Mode required). When not using Exact Frequency
Mode and Auto seed Enable Reg06h[8] =1, Reg1Ah sets the start
phase of output signal. If AutoSeed disable Reg06h[8] =0, Reg1Ah is
the start phase of the signal after every frequency change. (LO Phase
= 2π x Reg1Ah/(224).
For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
PLLs WITH INTEGRATED VCO - SMT
2.24
52