F49L320UA/F49L320BA (2F)

ESMT
F49L320UA/F49L320BA (2F)
Flash
32 Mbit (4M x 8/2M x 16)
3V Only CMOS Flash Memory
1. FEATURES
z
z
z
z
z
z
z
z
z
z
z
z
Single supply voltage 2.7V-3.6V
Fast access time
- Random access time: 70/90 ns
- Page access times: 30ns
z
4,194,304x8 / 2,097,152x16 switchable by BYTE pin
Compatible with JEDEC standard
- Pin-out, packages and software commands compatible
with single-power supply Flash
Low power consumption
- 20mA typical active current
- 25uA typical standby current 
100,000 program/erase cycles typically
20 Years Data Retention 
Command register architecture
- Byte / Word Programming (9μs/11μs typical)
- Byte Mode: eight 8KB, sixty three 64KB sectors.
- Word Mode: eight 4K word, sixty-three 32K word sectors.
Page read mode device
- 8 words page size
Auto Erase (chip & sector) and Auto Program
- Any combination of sectors can be erased concurrently;
Chip erase also provided
- Automatically program and verify data at specified
address
Erase Suspend/Erase Resume
- Suspend or Resume erasing sectors to allow the
read/program in another sector
Secured Silicon Sector
- 128word sector for permanent, secure identification
through an 8- word random Electronic Serial Number
- May be programmed and locked at the factory or by the
customer
- Accessible through a command sequence
z
z
z
z
z
z
z
z
Ready/Busy (RY/ BY )
- RY/ BY output pin for detection of program or erase
operation completion
End of program or erase detection
- Data polling
- Toggle bits
Hardware reset
- Hardware pin ( RESET ) resets the internal state machine to
the read mode
Sector Group Protection / Chip Unprotection
- Hardware Protect/Unprotect any combination of sectors from
a program or erase operation.
CFI (Common Flash Interface) complaint
- Provides device-specific information to the system, allowing
host software to easily reconfigure to different Flash devices
WP /ACC input pin
- Write protect ( WP ) function allows protection of two
outermost boot sectors, regardless of sector protect status
- Acceleration (ACC) function provides accelerated program
times
Low VCC Write inhibit is equal to or less than VLKO
Boot Sector Architecture
- U = Upper Boot Block
- B = Bottom Boot Block
Packages available:
- 48-pin TSOPI
- All Pb-free products are RoHS-Compliant
2. ORDERING INFORMATION
Product ID
F49L320UA-70TG2F
F49L320BA-70TG2F
F49L320UA-90TG2F
F49L320BA-90TG2F
Boot
Speed
Package
Comments
Upper
Bottom
Upper
Bottom
70 ns
70 ns
90 ns
90 ns
TSOPI
TSOPI
TSOPI
TSOPI
Pb-free
Pb-free
Pb-free
Pb-free
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
1/57
ESMT
F49L320UA/F49L320BA (2F)
3. GENERAL DESCRIPTION
The F49L320UA/F49L320BA is a 32 Megabit, 3V only CMOS
Flash memory device organized as 4M bytes of 8 bits or 2M
words of 16bits. This device is packaged in standard 48-pin
TSOP. It is designed to be programmed and erased both in
system and can in standard EPROM programmers.
With access times of 70 ns and 90 ns, the
F49L320UA/F49L320BA allows the operation of high-speed
microprocessors. The device has separate chip enable CE ,
write enable WE , and output enable OE controls. ESMT’s
memory devices reliably store memory data even after
100,000 program and erase cycles.
The F49L320UA/F49L320BA is entirely pin and command
set compatible with the JEDEC standard for 32 Megabit
Flash memory devices. Commands are written to the
command register using standard microprocessor write
timings. Register contents serve as input to an internal
state-machine that controls the erase and programming
circuitry. Write cycles also internally latch addresses and
data needed for the programming and erase operations.
Reading data out of the device is similar to reading from
other Flash or EPROM devices.
Elite Semiconductor Memory Technology Inc.
The F49L320UA/F49L320BA features a sector erase
architecture. The device array is divided into eight 8KB,
sixty-three 64KB for byte mode. The device memory
array is divided into eight 4K word, sixty-three 32K word
sectors for word mode. Sectors can be erased
individually or in groups without affecting the data in other
sectors. Multiple-sector erase and whole chip erase
capabilities provide the flexibility to revise the data in the
device.
The sector group protect/chip unprotect feature disables
both program and erase operations in any combination of
the sectors of the memory. This can be achieved
in-system or via programming equipment.
A low VCC detector inhibits write operations on loss of
power. End of program or erase is detected by the
Ready/Busy status pin, Data Polling of DQ7, or by the
Toggle Bit I feature on DQ6. Once the program or erase
cycle has been successfully completed, the device
internally resets to the Read mode. The command
register using standard microprocessor write timings.
Publication Date :
Revision: 1.0
Jul. 2012
2/57
ESMT
F49L320UA/F49L320BA (2F)
4. PIN CONFIGURATION (TOP VIEW)
4.1
TSOPI 48L, 12mm X 20mm Body, 0.5mm Pin Pitch
4.2
Pin Description
Symbol
Pin Name
A0~A20
Address Input
DQ0~DQ14
Data Input/Output
Functions
To provide memory addresses.
To output data when Read and receive data when Write.
The outputs are in tri-state when OE or CE is high.
Q15 (Word mode) /
LSB addr (Byte Mode)
To bi-direction date I/O when BYTE is High
CE
Chip Enable
To activate the device when CE is low.
OE
Output Enable
To gate the data output buffers.
WE
Write Enable
To control the Write operations.
DQ15/A-1
To input address when BYTE is Low
RESET
Reset
Hardware Reset Pin/Sector Group Protect & Chip Unprotect
WP /ACC
Write Protect / Acceleration
Hardware Write Protect / Programming Acceleration Pin
BYTE
Word/Byte selection input
To select word mode or byte mode
RY/ BY
VCC
VSS
NC
Ready/Busy
Power Supply
Ground
No connection
To check device operation status
To provide power
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
3/57
ESMT
F49L320UA/F49L320BA (2F)
5. SECTOR STRUCTURE
Table 1: F49L320UA Sector Address Table
Sector
Group
1
2
3
4
5
6
7
8
9
Sector
Sector Size
Address range
Sector Address
Byte Mode
Word Mode
Byte Mode (x8)
Word Mode (x16)
A20
A19
A18
A17
A16
A15
A14
A13
A12
SA0
64Kbytes
32Kwords
000000-00FFFF
00000-07FFF
0
0
0
0
0
0
X
X
X
SA1
64Kbytes
32Kwords
010000-01FFFF
08000-0FFFF
0
0
0
0
0
1
X
X
X
SA2
64Kbytes
32Kwords
020000-02FFFF
10000-17FFF
0
0
0
0
1
0
X
X
X
SA3
64Kbytes
32Kwords
030000-03FFFF
18000-1FFFF
0
0
0
0
1
1
X
X
X
SA4
64Kbytes
32Kwords
040000-04FFFF
20000-27FFF
0
0
0
1
0
0
X
X
X
SA5
64Kbytes
32Kwords
050000-05FFFF
28000-2FFFF
0
0
0
1
0
1
X
X
X
SA6
64Kbytes
32Kwords
060000-06FFFF
30000-37FFF
0
0
0
1
1
0
X
X
X
SA7
64Kbytes
32Kwords
070000-07FFFF
38000-3FFFF
0
0
0
1
1
1
X
X
X
SA8
64Kbytes
32Kwords
080000-08FFFF
40000-47FFF
0
0
1
0
0
0
X
X
X
SA9
64Kbytes
32Kwords
090000-09FFFF
48000-4FFFF
0
0
1
0
0
1
X
X
X
SA10
64Kbytes
32Kwords
0A0000-0AFFFF
50000-57FFF
0
0
1
0
1
0
X
X
X
SA11
64Kbytes
32Kwords
0B0000-0BFFFF
58000-5FFFF
0
0
1
0
1
1
X
X
X
SA12
64Kbytes
32Kwords
0C0000-0CFFFF
60000-67FFF
0
0
1
1
0
0
X
X
X
SA13
64Kbytes
32Kwords
0D0000-0DFFFF
68000-6FFFF
0
0
1
1
0
1
X
X
X
SA14
64Kbytes
32Kwords
0E0000-0EFFFF
70000-77FFF
0
0
1
1
1
0
X
X
X
SA15
64Kbytes
32Kwords
0F0000-0FFFFF
78000-7FFFF
0
0
1
1
1
1
X
X
X
SA16
64Kbytes
32Kwords
100000-10FFFF
80000-87FFF
0
1
0
0
0
0
X
X
X
SA17
64Kbytes
32Kwords
110000-11FFFF
88000-8FFFF
0
1
0
0
0
1
X
X
X
SA18
64Kbytes
32Kwords
120000-12FFFF
90000-97FFF
0
1
0
0
1
0
X
X
X
SA19
64Kbytes
32Kwords
130000-13FFFF
98000-9FFFF
0
1
0
0
1
1
X
X
X
SA20
64Kbytes
32Kwords
140000-14FFFF
A0000-A7FFF
0
1
0
1
0
0
X
X
X
SA21
64Kbytes
32Kwords
150000-15FFFF
A8000-AFFFF
0
1
0
1
0
1
X
X
X
SA22
64Kbytes
32Kwords
160000-16FFFF
B0000-B7FFF
0
1
0
1
1
0
X
X
X
SA23
64Kbytes
32Kwords
170000-17FFFF
B8000-BFFF
0
1
0
1
1
1
X
X
X
SA24
64Kbytes
32Kwords
180000-18FFFF
C0000-C7FFF
0
1
1
0
0
0
X
X
X
SA25
64Kbytes
32Kwords
190000-19FFFF
C8000-CFFFF
0
1
1
0
0
1
X
X
X
SA26
64Kbytes
32Kwords
1A0000-1AFFFF
D0000-D7FFF
0
1
1
0
1
0
X
X
X
SA27
64Kbytes
32Kwords
1B0000-1BFFFF
D8000-DFFFF
0
1
1
0
1
1
X
X
X
SA28
64Kbytes
32Kwords
1C0000-1CFFFF
E0000-E7FFF
0
1
1
1
0
0
X
X
X
SA29
64Kbytes
32Kwords
1D0000-1DFFFF
E8000-EFFFF
0
1
1
1
0
1
X
X
X
SA30
64Kbytes
32Kwords
1E0000-1EFFFF
F0000-F7FFF
0
1
1
1
1
0
X
X
X
SA31
64Kbytes
32Kwords
1F0000-1FFFFF
F8000-FFFFF
0
1
1
1
1
1
X
X
X
SA32
64Kbytes
32Kwords
200000-20FFFF
100000-107FFF
1
0
0
0
0
0
X
X
X
SA33
64Kbytes
32Kwords
210000-21FFFF
108000-10FFFF
1
0
0
0
0
1
X
X
X
SA34
64Kbytes
32Kwords
220000-22FFFF
110000-117FFF
1
0
0
0
1
0
X
X
X
SA35
64Kbytes
32Kwords
230000-23FFFF
118000-11FFFF
1
0
0
0
1
1
X
X
X
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
4/57
ESMT
F49L320UA/F49L320BA (2F)
Table 1: F49L320UA Sector Address Table - Continued
Sector
Group
Sector
Sector Size
Address range
Sector Address
Byte Mode
Word Mode
Byte Mode (x8)
Word Mode (x16)
A20
A19
A18
A17
A16
A15
A14
A13
A12
SA36
64Kbytes
32Kwords
240000-24FFFF
120000-127FFF
1
0
0
1
0
0
X
X
X
SA37
64Kbytes
32Kwords
250000-25FFFF
128000-12FFFF
1
0
0
1
0
1
X
X
X
SA38
64Kbytes
32Kwords
260000-26FFFF
130000-137FFF
1
0
0
1
1
0
X
X
X
SA39
64Kbytes
32Kwords
270000-27FFFF
138000-13FFFF
1
0
0
1
1
1
X
X
X
SA40
64Kbytes
32Kwords
280000-28FFFF
140000-147FFF
1
0
1
0
0
0
X
X
X
SA41
64Kbytes
32Kwords
290000-29FFFF
148000-14FFFF
1
0
1
0
0
1
X
X
X
SA42
64Kbytes
32Kwords
2A0000-2AFFFF
150000-157FFF
1
0
1
0
1
0
X
X
X
SA43
64Kbytes
32Kwords
2B0000-2BFFFF
158000-15FFFF
1
0
1
0
1
1
X
X
X
SA44
64Kbytes
32Kwords
2C0000-2CFFFF
160000-167FFF
1
0
1
1
0
0
X
X
X
SA45
64Kbytes
32Kwords
2D0000-2DFFFF
168000-16FFFF
1
0
1
1
0
1
X
X
X
SA46
64Kbytes
32Kwords
2E0000-2EFFFF
170000-177FFF
1
0
1
1
1
0
X
X
X
SA47
64Kbytes
32Kwords
2F0000-2FFFFF
178000-17FFFF
1
0
1
1
1
1
X
X
X
SA48
64Kbytes
32Kwords
300000-30FFFF
180000-187FFF
1
1
0
0
0
0
X
X
X
SA49
64Kbytes
32Kwords
310000-31FFFF
188000-18FFFF
1
1
0
0
0
1
X
X
X
SA50
64Kbytes
32Kwords
320000-32FFFF
190000-197FFF
1
1
0
0
1
0
X
X
X
SA51
64Kbytes
32Kwords
330000-33FFFF
198000-19FFFF
1
1
0
0
1
1
X
X
X
SA52
64Kbytes
32Kwords
340000-34FFFF
1A0000-1A7FFF
1
1
0
1
0
0
X
X
X
SA53
64Kbytes
32Kwords
350000-35FFFF
1A8000-1AFFFF
1
1
0
1
0
1
X
X
X
SA54
64Kbytes
32Kwords
360000-36FFFF
1B0000-1B7FFF
1
1
0
1
1
0
X
X
X
SA55
64Kbytes
32Kwords
370000-37FFFF
1B8000-1BFFFF
1
1
0
1
1
1
X
X
X
SA56
64Kbytes
32Kwords
380000-38FFFF
1C0000-1C7FFF
1
1
1
0
0
0
X
X
X
SA57
64Kbytes
32Kwords
390000-39FFFF
1C8000-1CFFFF
1
1
1
0
0
1
X
X
X
SA58
64Kbytes
32Kwords
3A0000-3AFFFF
1D0000-1D7FFF
1
1
1
0
1
0
X
X
X
SA59
64Kbytes
32Kwords
3B0000-3BFFFF
1D8000-1DFFFF
1
1
1
0
1
1
X
X
X
SA60
64Kbytes
32Kwords
3C0000-3CFFFF
1E0000-1E7FFF
1
1
1
1
0
0
X
X
X
SA61
64Kbytes
32Kwords
3D0000-3DFFFF
1E8000-1EFFFF
1
1
1
1
0
1
X
X
X
SA62
64Kbytes
32Kwords
3E0000-3EFFFF
1F0000-1F7FFF
1
1
1
1
1
0
X
X
X
17
SA63
8Kbytes
4Kwords
3F0000-3F1FFF
1F8000-1F8FFF
1
1
1
1
1
1
0
0
0
18
SA64
8Kbytes
4Kwords
3F2000-3F3FFF
1F9000-1F9FFF
1
1
1
1
1
1
0
0
1
19
SA65
8Kbytes
4Kwords
3F4000-3F5FFF
1FA000-1FAFFF
1
1
1
1
1
1
0
1
0
20
SA66
8Kbytes
4Kwords
3F6000-3F7FFF
1FB000-1FBFFF
1
1
1
1
1
1
0
1
1
21
SA67
8Kbytes
4Kwords
3F8000-3F9FFF
1FC000-1FCFFF
1
1
1
1
1
1
1
0
0
22
SA68
8Kbytes
4Kwords
3FA000-3FBFFF
1FD000-1FDFFF
1
1
1
1
1
1
1
0
1
23
SA69
8Kbytes
4Kwords
3FC000-3FDFFF
1FE000-1FEFFF
1
1
1
1
1
1
1
1
0
24
SA70
8Kbytes
4Kwords
3FE000-3FFFFF
1FF000-1FFFFF
1
1
1
1
1
1
1
1
1
10
11
12
13
14
15
16
Note: Byte Mode: address range A20 : A-1, Word mode : address range A20 : A0
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
5/57
ESMT
F49L320UA/F49L320BA (2F)
Table 2: F49L320BA Sector Address Table
Sector
Group
Sector
1
Sector Size
Address range
Byte Mode
Word Mode
Byte Mode (x8)
SA0
8Kbytes
4Kwords
000000-001FFF
00000-00FFF
2
SA1
8Kbytes
4Kwords
002000-003FFF
3
SA2
8Kbytes
4Kwords
4
SA3
8Kbytes
5
SA4
6
Sector Address
A19
A18
A17
A16
A15
A14
A13
A12
0
0
0
0
0
0
0
0
0
01000-01FFF
0
0
0
0
0
0
0
0
1
004000-005FFF
02000-02FFF
0
0
0
0
0
0
0
1
0
4Kwords
006000-007FFF
03000-03FFF
0
0
0
0
0
0
1
1
1
8Kbytes
4Kwords
008000-009FFF
04000-04FFF
0
0
0
0
0
0
1
0
0
SA5
8Kbytes
4Kwords
00A000-00BFFF
05000-05FFF
0
0
0
0
0
0
1
0
1
7
SA6
8Kbytes
4Kwords
00C000-00DFFF
06000-06FFF
0
0
0
0
0
0
1
1
0
8
SA7
8Kbytes
4Kwords
00E000-00FFFF
07000-07FFF
0
0
0
0
0
0
1
1
1
SA8
64Kbytes
32Kwords
010000-01FFFF
08000-0FFFF
0
0
0
0
0
1
X
X
X
SA9
64Kbytes
32Kwords
020000-02FFFF
010000-017FFF
0
0
0
0
1
0
X
X
X
SA10
64Kbytes
32Kwords
030000-03FFFF
018000-01FFFF
0
0
0
0
1
1
X
X
X
SA11
64Kbytes
32Kwords
040000-04FFFF
020000-027FFF
0
0
0
1
0
0
X
X
X
SA12
64Kbytes
32Kwords
050000-05FFFF
028000-02FFFF
0
0
0
1
0
1
X
X
X
SA13
64Kbytes
32Kwords
060000-06FFFF
030000-037FFF
0
0
0
1
1
0
X
X
X
SA14
64Kbytes
32Kwords
070000-07FFFF
038000-03FFFF
0
0
0
1
1
1
X
X
X
SA15
64Kbytes
32Kwords
080000-08FFFF
040000-047FFF
0
0
1
0
0
0
X
X
X
SA16
64Kbytes
32Kwords
090000-09FFFF
048000-04FFFF
0
0
1
0
0
1
X
X
X
SA17
64Kbytes
32Kwords
0A0000-0AFFFF
050000-057FFF
0
0
1
0
1
0
X
X
X
SA18
64Kbytes
32Kwords
0B0000-0BFFFF
058000-05FFFF
0
0
1
0
1
1
X
X
X
SA19
64Kbytes
32Kwords
0C0000-0CFFFF
060000-067FFF
0
0
1
1
0
0
X
X
X
SA20
64Kbytes
32Kwords
0D0000-0DFFFF
068000-06FFFF
0
0
1
1
0
1
X
X
X
SA21
64Kbytes
32Kwords
0E0000-0EFFFF
070000-077FFF
0
0
1
1
1
0
X
X
X
SA22
64Kbytes
32Kwords
0F0000-0FFFFF
078000-07FFFF
0
0
1
1
1
1
X
X
X
SA23
64Kbytes
32Kwords
100000-10FFFF
080000-087FFF
0
1
0
0
0
0
X
X
X
SA24
64Kbytes
32Kwords
110000-11FFFF
088000-08FFFF
0
1
0
0
0
1
X
X
X
SA25
64Kbytes
32Kwords
120000-12FFFF
090000-097FFF
0
1
0
0
1
0
X
X
X
SA26
64Kbytes
32Kwords
130000-13FFFF
098000-09FFFF
0
1
0
0
1
1
X
X
X
SA27
64Kbytes
32Kwords
140000-14FFFF
0A0000-0A7FFF
0
1
0
1
0
0
X
X
X
SA28
64Kbytes
32Kwords
150000-15FFFF
0A8000-0AFFFF
0
1
0
1
0
1
X
X
X
SA29
64Kbytes
32Kwords
160000-16FFFF
0B0000-0B7FFF
0
1
0
1
1
0
X
X
X
SA30
64Kbytes
32Kwords
170000-17FFFF
0B8000-0BFFFF
0
1
0
1
1
1
X
X
X
SA31
64Kbytes
32Kwords
180000-18FFFF
0C0000-0C7FFF
0
1
1
0
0
0
X
X
X
SA32
64Kbytes
32Kwords
190000-19FFFF
0C8000-0CFFFF
0
1
1
0
0
1
X
X
X
SA33
64Kbytes
32Kwords
1A0000-1AFFFF
0D0000-0D7FFF
0
1
1
0
1
0
X
X
X
SA34
64Kbytes
32Kwords
1B0000-1BFFFF
0D8000-0DFFFF
0
1
1
0
1
1
X
X
X
9
10
11
12
13
14
15
Elite Semiconductor Memory Technology Inc.
Word Mode (x16) A20
Publication Date :
Revision: 1.0
Jul. 2012
6/57
ESMT
F49L320UA/F49L320BA (2F)
Table 2: F49L320BA Sector Address Table - Continued
Sector
Group
16
17
18
19
20
21
22
23
24
Sector
Sector Size
Address range
Byte Mode
Word Mode
Byte Mode (x8)
SA35
64Kbytes
32Kwords
1C0000-1CFFFF
0E0000-0E7FFF
SA36
64Kbytes
32Kwords
1D0000-1DFFFF
SA37
64Kbytes
32Kwords
SA38
64Kbytes
SA39
Sector Address
Word Mode (x16) A20
A19
A18
A17
A16
A15
A14
A13
A12
0
1
1
1
0
0
X
X
X
0E8000-0EFFFF
0
1
1
1
0
1
X
X
X
1E0000-1EFFFF
0F0000-0F7FFF
0
1
1
1
1
0
X
X
X
32Kwords
1F0000-1FFFFF
0F8000-0FFFFF
0
1
1
1
1
1
X
X
X
64Kbytes
32Kwords
200000-20FFFF
100000-107FFF
1
0
0
0
0
0
X
X
X
SA40
64Kbytes
32Kwords
210000-21FFFF
108000-10FFFF
1
0
0
0
0
1
X
X
X
SA41
64Kbytes
32Kwords
220000-22FFFF
110000-117FFF
1
0
0
0
1
0
X
X
X
SA42
64Kbytes
32Kwords
230000-23FFFF
118000-11FFFF
1
0
0
0
1
1
X
X
X
SA43
64Kbytes
32Kwords
240000-24FFFF
120000-127FFF
1
0
0
1
0
0
X
X
X
SA44
64Kbytes
32Kwords
250000-25FFFF
128000-12FFFF
1
0
0
1
0
1
X
X
X
SA45
64Kbytes
32Kwords
260000-26FFFF
130000-137FFF
1
0
0
1
1
0
X
X
X
SA46
64Kbytes
32Kwords
270000-27FFFF
138000-13FFFF
1
0
0
1
1
1
X
X
X
SA47
64Kbytes
32Kwords
280000-28FFFF
140000-147FFF
1
0
1
0
0
0
X
X
X
SA48
64Kbytes
32Kwords
290000-29FFFF
148000-14FFFF
1
0
1
0
0
1
X
X
X
SA49
64Kbytes
32Kwords
2A0000-2AFFFF
150000-157FFF
1
0
1
0
1
0
X
X
X
SA50
64Kbytes
32Kwords
2B0000-2BFFFF
158000-15FFFF
1
0
1
0
1
1
X
X
X
SA51
64Kbytes
32Kwords
2C0000-2CFFFF
160000-167FFF
1
0
1
1
0
0
X
X
X
SA52
64Kbytes
32Kwords
2D0000-2DFFFF
168000-16FFFF
1
0
1
1
0
1
X
X
X
SA53
64Kbytes
32Kwords
2E0000-2EFFFF
170000-177FFF
1
0
1
1
1
0
X
X
X
SA54
64Kbytes
32Kwords
2F0000-2FFFFF
178000-17FFFF
1
0
1
1
1
1
X
X
X
SA55
64Kbytes
32Kwords
300000-30FFFF
180000-187FFF
1
1
0
0
0
0
X
X
X
SA56
64Kbytes
32Kwords
310000-31FFFF
188000-18FFFF
1
1
0
0
0
1
X
X
X
SA57
64Kbytes
32Kwords
320000-32FFFF
190000-197FFF
1
1
0
0
1
0
X
X
X
SA58
64Kbytes
32Kwords
330000-33FFFF
198000-19FFFF
1
1
0
0
1
1
X
X
X
SA59
64Kbytes
32Kwords
340000-34FFFF
1A0000-1A7FFF
1
1
0
1
0
0
X
X
X
SA60
64Kbytes
32Kwords
350000-35FFFF
1A8000-1AFFFF
1
1
0
1
0
1
X
X
X
SA61
64Kbytes
32Kwords
360000-36FFFF
1B0000-1B7FFF
1
1
0
1
1
0
X
X
X
SA62
64Kbytes
32Kwords
370000-37FFFF
1B8000-1BFFFF
1
1
0
1
1
1
X
X
X
SA63
64Kbytes
32Kwords
380000-38FFFF
1C0000-1C7FFF
1
1
1
0
0
0
X
X
X
SA64
64Kbytes
32Kwords
390000-39FFFF
1C8000-1CFFFF
1
1
1
0
0
1
X
X
X
SA65
64Kbytes
32Kwords
3A0000-3AFFFF
1D0000-1D7FFF
1
1
1
0
1
0
X
X
X
SA66
64Kbytes
32Kwords
3B0000-3BFFFF
1D8000-1DFFFF
1
1
1
0
1
1
X
X
X
SA67
64Kbytes
32Kwords
3C0000-3CFFFF
1E0000-1E7FFF
1
1
1
1
0
0
X
X
X
SA68
64Kbytes
32Kwords
3D0000-3DFFFF
1E8000-1EFFFF
1
1
1
1
0
1
X
X
X
SA69
64Kbytes
32Kwords
3E0000-3EFFFF
1F0000-1F7FFF
1
1
1
1
1
0
X
X
X
SA70
64Kbytes
32Kwords
3F0000-3FFFFF
1F8000-1FFFFF
1
1
1
1
1
1
X
X
X
Note: Byte Mode: address range A20 : A-1, Word mode : address range A20 : A0
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
7/57
ESMT
F49L320UA/F49L320BA (2F)
6. FUNCTIONAL BLOCK DIAGRAM
BYTE
CE
OE
WE
RESET
WP/ACC
RY/BY
A0~A20
CONTROL
INPUT
LOGIC
ADDRESS
LATCH
AND
BUFFER
PROGRAM / ERASE HIGH
VOLTAGE
FLASH
ARRAY
STATE
REGISTER
ARRAY
SOURCE
HV
Y-PASS GATE
SENSE
AMPLIFIER
WRITE
STATE
MACHINE
(WSM)
PGM
DATA
HV
COMMAND
DATA
DECODER
COMMAND
DATA LATCH
PROGRAM
DATA
LOATCH
DQ0~DQ14
I/O BUFFER
DQ15 / A-1
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
8/57
ESMT
F49L320UA/F49L320BA (2F)
7. FUNCTIONAL DESCRIPTION
7.1 Device operation
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The register is composed of
latches that store the command, address and data
information needed to execute the command. The contents
of the register serve as inputs to the internal state machine.
The state machine outputs dictate the function of the device.
The F49L320UA/F49L320BA features various bus
operations as Table 3.
Table 3: F49L320UA/F49L320BA Operation Modes Selection
Operation
Read
Write(Note1)
Accelerated
Program
OE
WE
RESET
WP /ACC
Addresses
(Note 2)
DQ0-DQ7
L
L
L
H
H
L
H
H
L/H
(Note 4)
AIN
AIN
DOUT
(Note 5)
DOUT
(Note 5)
L
H
L
H
VID
AIN
(Note 5)
(Note 5)
DQ8-DQ14
= High-Z,
DQ15 = A-1
X
High-Z
High-Z
High-Z
H
X
L/H
L/H
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
H
L
VID
L/H
(Note 5)
X
X
L
H
L
VID
(Note 4)
X
X
SA, A6 = L,
A1 = H, A0 =L
SA, A6 = H,
A1 = H, A0 = L
(Note 5)
X
X
X
X
X
VID
(Note 4)
AIN
(Note 5)
(Note 5)
High-Z
X
H
X
L
Chip Unprotect
(Note 3)
Temporary Sector
Group Unprotect
Notes: 1.
BYTE =VIL
H
X
Output Disable
Reset
Sector Group
Protect (Note 3)
BYTE =VIH
VCC
± 0.3
H
L
VCC
± 0.3
L
X
Standby
DQ8-DQ15
CE
When the ACC pin is at VID, the device enters the accelerated program mode.
2. Addresses are A20:A0 in word mode ( BYTE = VIH), A20:A-1 in byte mode ( BYTE = VIL).
3. The sector group protect and chip unprotect functions may also be implemented via programming equipment.
4. If WP /ACC = VIL, the two outermost boot sectors remain protected. If WP /ACC = VIH, the two outermost boot sector
protection depends on whether they were last protected or unprotected. If WP /ACC = VID, all sectors are unprotected.
5. DIN or DOUT as required by command sequence, data polling, or sector group protection algorithm.
Write Protect / Accelerated Program ( WP /ACC)
The WP /ACC pin provides two functions. The write protect
( WP ) function provides a hardware method of protecting
certain boot sectors without using VID. The ACC function
allows faster manufacturing throughput at the factory with an
external high voltage (VID).
If the system asserts VIL on the WP /ACC pin, the device
disables program and erase functions in the two outermost
8-Kbyte boot sectors independently of whether those sectors
were protected or unprotected using the sector group protect
and chip unprotect method. The two outermost 8-Kbyte boot
sectors are the two sectors containing the lowest addresses
in a bottom-boot configured device, or the two sectors
containing the highest addresses in a top-boot configured
device.
If the system asserted VIH on the WP /ACC pin, the device
reverts to whether the two outermost 8-Kbyte boot sectors
were last set to be protected or unprotected. That is, sector
protection or unprotection for these two sectors depends on
Elite Semiconductor Memory Technology Inc.
whether they were last protected or unprotected using the
sector group protect and chip unprotect method.
If the system asserts VID on this pin, the device automatically
enters the accelerated program mode, temporarily unprotects
any protected sectors, and uses the higher voltage on the pin
to reduce the time required for program operations.
Removing VID from the WP /ACC pin returns the device to
normal operation.
Note that the WP /ACC pin must not be at VID for operations
other than accelerated programming, or device damage may
result. In addition, the WP /ACC pin must not be left floating
or unconnected; inconsistent behavior of the device may
result.
Publication Date :
Revision: 1.0
Jul. 2012
9/57
ESMT
F49L320UA/F49L320BA (2F)
Table 4: F49L320UA/F49L320BA Auto-Select Mode (High Voltage Method)
Description
Mode
Manufacturer ID:
ESMT
CE
OE
WE
L
L
H
Device ID:
F49L320UA
Word
L
L
H
Byte
L
L
H
Device ID:
F49L320BA
Word
L
L
H
Byte
L
L
H
A20
to
A12
A11
to
A10
A9
A8
to
A7
A6
A5
to
A4
A3
A2
A1
A0
DQ8
to
DQ15
L
H
L
H
L
L
X
X
X
VID
X
L
X
L
L
H
H
X
X
VID
X
L
X
L
L
L
H
X
X
VID
X
L
X
L
L
L
H
22h
F6h
X
F6h
22h
F9h
X
F9h
X
Sector Protection
Verification
L
Sector Silicon
Sector Indicator Bit
(DQ7) F49L320UA
L
Sector Silicon
Sector Indicator Bit
(DQ7) F49L320BA
L
L
H
SA
X
VID
X
L
X
L
L
H
L
X
X
L
H
X
X
VID
X
L
X
L
L
H
H
X
X
L
H
X
X
VID
X
L
X
L
L
H
DQ7
to
DQ0
8Ch
7Fh
7Fh
7Fh
H
X
01h
(protected)
00h
(unprotected)
8D (factory
locked)
0D (not factory
locked)
9D (factory
locked)
1D (not factory
locked)
Notes:
L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care.
1. Manufacturer and device codes may also be accessed via the software command sequence in Table 5.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
10/57
ESMT
Reset Mode :
Hardware Reset
When the RESET pin is driven low for at least a period of
tRP, the device immediately terminates any operation in
progress, tri-states all output pins, and ignores all read/write
commands for the duration of the RESET pulse. The device
also resets the internal state machine to reading array data.
The operation that was interrupted should be reinitiated later
once the device is ready to accept another command
sequence, to ensure the data integrity.
The current is reduced for the duration of the RESET pulse.
When RESET is held at VSS ±0.3V, the device draws CMOS
standby current (ICC4). If RESET is held at VIL but not within
VSS±0.3V, the standby current will be greater.
The RESET pin may be tied to system reset circuitry. A
system reset would thus reset the Flash memory, enabling
the system to read the boot-up firm-ware from the Flash
memory.
If RESET is asserted during a program or erase embedded
algorithm operation, the RY/ BY pin remains a "0" (busy) until
the internal reset operation is complete, which requires a time
of tREADY (during Embedded Algorithms). The system can thus
monitor RY/ BY to determine whether the reset operation is
complete.
If RESET is asserted when a program or erase operation is
not executing, i.e. the RY/ BY is “1”, the reset operation is
completed within a time of tREADY (not during Embedded
Algorithms). The system can read data after tRH when the
RESET pin returns to VIH. Refer to the AC Characteristics
tables 17 for Hardware Reset section & Figure 24 for the
timing diagram.
F49L320UA/F49L320BA (2F)
See “Read Command” section for more information. Refer to
the AC Read Operations table 14 for timing specifications and
to Figure 5 for the timing diagram. ICC1 in the DC
Characteristics table represents the active current
specification for reading array data.
Page Read
The device is capable of fast page mode read and the page
size is 8 words. After initial page access is accomplished, this
mode provides faster read access speed for random
locations within a page. Address bits A20–A3 select an 8
word page, and address bits A2–A0 select a specific word
within that page. Table 3.3 shows how the page is selected
by address bits A2-A0. This is an asynchronous operation
with the microprocessor supplying the specific word location.
The random or initial page access is tACC or tCE and
subsequent page read accesses (as long as the locations
specified by the microprocessor falling within that page) is
equivalent to tPACC. When CE is de-asserted (= VIH), the
reassertion of CE for subsequent access has access time of
tACC or tCE. Here again, CE selects the device and OE is
the output control and should be used to gate data to the
output inputs if the device is selected. Fast page mode
accesses are obtained by keeping A20–A3 constant and
changing A2–A0 to select the specific word within that page.
Word
A2
A1
A0
Word 0
0
0
0
Word 1
0
0
1
Word 2
0
1
0
Word 3
0
1
1
Word 4
1
0
0
Read Mode
Word 5
1
0
1
To read array data from the outputs, the system must drive
the CE and OE pins to VIL. CE is the power control and
Word 6
1
1
0
Word 7
1
1
1
selects the device. OE is the output control and gates array
data to the output pins. WE should remain at VIH. The
internal state machine is set for reading array data upon
device power-up, or after a hardware reset. This ensures that
no spurious alteration of the memory content occurs during
the power transition.
No command is necessary in this mode to obtain array data.
Standard microprocessor’s read cycles that assert valid
addresses on the device address inputs produce valid data
on the device data outputs. The device remains enabled for
read access until the command register contents are altered.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
11/57
ESMT
F49L320UA/F49L320BA (2F)
Write Mode
Automatic Sleep Mode
To write a command or command sequence (which includes
programming data to the device and erasing sectors of
memory), the system must drive WE and CE to VIL, and
The automatic sleep mode minimizes Flash device energy
consumption. The device automatically enables this mode
when addresses remain unchanged for over 250ns. The
automatic sleep mode is independent of the CE , WE , and
OE to VIH. The “Program Command” section has details on
programming data to the device using standard command
sequences.
An erase operation can erase one sector, multiple sectors, or
the entire device. Tables 1 and 2 indicate the address space
that each sector occupies. A “sector address” consists of the
address bits required to uniquely select a sector. The
“Software Command Definitions” section has details on
erasing a sector or t he entire chip, or suspending/resuming
the erase operation.
When the system writes the auto-select command sequence,
the device enters the auto-select mode. The system can then
read auto-select codes from the internal register (which is
separate from the memory array) on DQ7–DQ0. Standard
read cycle timings apply in this mode. Refer to the Auto-select
Mode and Auto-select Command sections for more
information. ICC2 in the DC Characteristics table represents
the active current specification for the write mode. The “AC
Characteristics” section contains timing specification tables
and timing diagrams for write operations.
Elite Semiconductor Memory Technology Inc.
OE control signals. Standard address access timings
provide new data when addresses are changed. While in
sleep mode, output data is latched and always available to
the system. ICC4 in the DC Characteristics table represents
the automatic sleep mode current specification.
Word / Byte Mode
This pin controls the I/O configuration of device. When
BYTE = VIH or Vcc ± 0.3V. The I/O configuration is x16 and t
he pin of D15/A-1 is bi-direction Data I/O. However, BYTE =
VIL or VSS ± 0.3V. The I/O configuration would be x8 and The
pin of DQ15/A-1 only address input pin. You must define the
function of this pin before enable this device.
Publication Date :
Revision: 1.0
Jul. 2012
12/57
ESMT
F49L320UA/F49L320BA (2F)
Temporary Sector Group Unprotect Mode
This feature allows
protected sectors to
activated by setting
During this mode,
temporary unprotection of previously
change data in-system. This mode is
the RESET pin to VID(10V -10.5V).
all formerly protected sectors are
un-protected and can be programmed or erased by selecting
the sector addresses. Once VID is removed from the RESET
pin, all the previously protected sectors are protected again.
Start
RESET = V ID (Note 1)
Perform Erase or
Program Operation
Operation Completed
RESET = V I H
Temporary Sector
Unprotect Completed
(Note 2)
Notes:
1. All protected sectors unprotected.
2. All previously protected sectors are protected once again.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
13/57
ESMT
Output Disable Mode
With the OE is at a logic high level (VIH), outputs from the
devices are disabled. This will cause the output pins in a high
impedance state
F49L320UA/F49L320BA (2F)
Figure 17 shows the algorithms and Figure 16 shows the
timing
diagram.
This
method
uses
standard
microprocessor bus cycle timing. For chip unprotect, all
unprotected sectors must first be protected prior to the first
chip unprotect write cycle.
The alternate method intended only for programming
Standby Mode
equipment requires VID on address pin A9, OE , and
RESET .
When CE and RESET are both held at VCC ± 0.3V, the
device enter CMOS Standby mode. If CE and RESET are
held at VIH, but not within the range of VCC ± 0.3V, the device
will still be in the standby mode, but the standby current will
be larger.
Auto-select Mode
If the device is deselected during auto algorithm of erasure or
programming, the device draws active current ICC2 until the
operation is completed. ICC3 in the DC Characteristics table
represents the standby current specification.
The device requires standard access time (tCE) for read
access from either of these standby modes, before it is ready
to read data.
Sector Group Protect / Chip Unprotect Mode
The hardware sector group protect feature disables both
program and erase operations in any sector. The hardware
chip unprotect feature re-enables both the program and erase
operations in previously protected sectors. Sector group
protect/chip unprotect can be implemented via two methods.
The primary method requires VID on the RESET pin only,
and can be implemented either in-system or via programming
equipment.
The auto-select mode provides manufacturer and device
identification and sector protection verification, through
outputs on DQ7–DQ0. This mode is primarily intended for
programming equipment to automatically match a device to
be programmed with its corresponding programming
algorithm. However, the auto-select codes can also be
accessed in-system through the command register.
When using programming equipment, this mode requires
VID (10 V to 10.5 V) on address pin A9. While address pins
A3, A2, A1, and A0 must be as shown in Table 4.
To verify sector protection, all necessary pins have to be
set as required in Table 4, the programming equipment
may then read the corresponding identifier code on
DQ7-DQ0.
To access the auto-select codes in-system, the host
system can issue the auto-select command via the
command register, as shown in Table 5. This method does
not require VID. See “Software Command Definitions” for
details on using the auto-select mode.
7.2 Software Command Definitions
Writing specific address and data commands or sequences
into the command register initiates the device operations.
Table 5 defines the valid register command sequences.
Writing incorrect address and data values or writing them in
the improper sequence resets the device to reading array
data.
Elite Semiconductor Memory Technology Inc.
All addresses are latched on the falling edge of WE or CE ,
whichever happens later. All data is latched on the rising
edge of WE or CE , whichever happens first. Refer to the
corresponding timing diagrams in the AC Characteristics
section.
Publication Date :
Revision: 1.0
Jul. 2012
14/57
ESMT
F49L320UA/F49L320BA (2F)
Table 5: F49L320UA/F49L320BA Software Command Definitions
Command Sequence
Cycles
Read Note 5
Reset Note 6
1
1
Word
Manufacturer ID
4
Autoselect Note 7
Word
Byte
Word
Device ID,
F49L320BA
Byte
Secured Silicon Sector Word
Factory Protect
Byte
F49L320UA Note 8
Secured Silicon Sector Word
Factory Protect
Byte
F49L320BA Note 8
Device ID,
F49L320UA
Sector Erase
Erase Suspend Note 11
Erase Resume Note 12
4
4
555
AAA
555
AAA
555
AAA
AAA
Byte
Word
Byte
Word
Byte
AA
AA
AA
1
4
6
6
1
1
2AA
555
2AA
555
2AA
555
555
AA
555
AAA
555
AAA
55
AA
555
AAA
555
AAA
555
AAA
XXX
XXX
55
55
55
AA
555
AAA
555
AAA
555
AAA
AAA
90
90
55
555
AAA
555
AAA
X06
XX8C
XX7F
XX7F
XX7F
8C
7F
7F
7F
22F6
F6
22F9
F9
8D/0D
X06
(SA)
X02
9D/1D
XX00
(SA)
X04
XX01
00
01
90
XXX
00
A0
PA
PD
90
AAA
55
X00
X04
X08
X0C
X00
X04
X08
X0C
X01
X02
X01
X02
X03
X03
90
555
55
2AA
555
2AA
555
90
555
55
555
AA
90
AAA
2AA
AAA
4
55
2AA
AA
555
3
555
555
555
4
Byte
Word
2AA
AA
4
Word
Byte
Exit Secured Silicon Sector Word
Region
Byte
Word
CFI Query Note 10
Byte
Chip Erase
4
Bus Cycle Note1~4
3rd
4th
5th
6th
Addr Data Addr Data Addr Data Addr Data
RD
F0
AAA
Word
Enter Secured Silicon
Sector Region
Program
RA
XXX
555
Byte
Sector Protect Verify
Note 9
1st
2nd
Addr Data Addr Data
88
98
AA
AA
AA
2AA
555
2AA
555
2AA
555
55
55
55
555
AAA
555
AAA
555
AAA
80
80
555
AAA
555
AAA
AA
AA
2AA
555
2AA
555
55
555
AAA
10
55
SA
30
B0
30
Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE or CE pulse, whichever
happens later.
PD = Data to be programmed at location PA. Data latches on the rising edge of WE or CE pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits A20–A12 uniquely select any sector.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
15/57
ESMT
F49L320UA/F49L320BA (2F)
Notes:
1. All values are in hexadecimal.
2. Except for the read cycle and the fourth cycle of the autoselect command sequence, all bus cycles are write cycles.
3. Data bits DQ15–DQ8 are don’t cares for unlock and command cycles.
4. Address bits A20–A11 are don’t cares for unlock and command cycles, unless SA or PA required.
5. No unlock or command cycles required when reading array data.
6. The Reset command is required to return to reading array data when device is in the autoselect mode, or if DQ5 goes high
(while the device is providing status data).
7. The fourth cycle of the autoselect command sequence is a read cycle.
8. For upper boot device, the data is 8Dh for factory locked and 0Dh for not factory locked. For bottom boot device, the data is
9Dh for factory locked and 1Dh for not factory locked.
9. The data is 00h for an unprotected sector and 01h for a protected sector. See “Autoselect Command Sequence” for more
information.
10. Command is valid when device is ready to read array data or when device is in autoselect mode.
11. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase operation.
12. The Erase Resume command is valid only during the Erase Suspend mode.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
16/57
ESMT
F49L320UA/F49L320BA (2F)
Reset Command
Program Command
Writing the reset command to the device resets the device to
reading array data. Address bits are all don’t cares for this
command.
The program command sequence programs one byte into
the device. Programming is a four-bus-cycle operation.
The program command sequence is initiated by writing two
unlock write cycles, followed by the program set-up
command. The program address and data are written next,
which in turn initiate the Embedded Program algorithm.
The system is not required to provide further controls or
timings. The device automatically provides internally
generated program pulses and verifies the programmed
cell margin.
The reset command may be written between the sequence
cycles in an erase command sequence before erasing
begins. This resets the device to reading array data. Once
erasure begins, however, the device ignores reset commands
until the operation is complete.
The reset command may be written between the sequence
cycles in a program command sequence before programming
begins. This resets the device to reading array data (also
applies to programming in Erase Suspend mode). Once
programming begins, however, the device ignores reset
commands until the operation is complete.
The reset command may be written between the sequence
cycles in an auto-select command sequence. Once in the
auto-select mode, the reset command must be written to
return to reading array data (also applies to auto-select during
Erase Suspend).
If DQ5 goes high (see “DQ5: Exceeded Timing Limits”
section) during a program or erase operation, writing the reset
command returns the device to reading array data (also
applies during Erase Suspend).
Read Command
The device is automatically set to reading array data after
device power-up. No commands are required to retrieve data.
The device is also ready to read array data after completing
an Embedded Program or Embedded Erase algorithm.
When the device accepts an Erase Suspend command, the
device enters the Erase Suspend mode. The system can read
array data using the standard read timings, except that if it
reads an address within erase-suspended sectors, the device
outputs status data. After completing a programming
operation in the Erase Suspend mode, the system may once
again read array data with the same exception. See “Erase
Suspend/Erase Resume Commands” for more information on
this mode.
The system must issue the reset command to re-enable the
device for reading array data if DQ5 goes high, or while in the
auto-select mode. See the “Reset Command” section. See
also the “Read Mode” in the “Device Operations section for
more information. Refer to Figure 5 for the timing diagram.
Elite Semiconductor Memory Technology Inc.
When the Embedded Program algorithm is complete, the
device then returns to reading array data and addresses
are no longer latched. The system can determine the
status of the program operation by using DQ7, DQ6, or
RY/ BY . See “Write Operation Status” section for more
information on these status bits.
Any commands written to the device during the Embedded
Program Algorithm are ignored. Note that a hardware reset
immediately terminates the programming operation. The
Program command sequence should be reinitiated once
the device has reset to reading array data, to ensure data
integrity.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed from a “0”
back to a “1”. Attempting to do so may halt the operation
and set DQ5 to “1”, or cause the Data Polling algorithm to
indicate the operation was successful. However, a
succeeding read will show that the data is still “0”. Only
erase operations can convert a “0” to a ”1”.
Chip Erase Command
Chip erase is a six-bus cycle operation. The chip erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase
algorithm.
The device does not require the system to preprogram
prior to erase. The Embedded Erase algorithm
automatically preprograms and verifies the entire memory
for an all zero data pattern prior to electrical erase.
Any commands written to the chip during the Embedded
Erase algorithm are ignored. Note that a hardware reset
during the chip erase operation immediately terminates the
operation. The Chip Erase command sequence should be
reinitiated once the device has returned to reading array
data, to ensure the data integrity.
Publication Date :
Revision: 1.0
Jul. 2012
17/57
ESMT
The system can determine the status of the erase operation
by using DQ7, DQ6, DQ2, or RY/ BY . See “Write Operation
Status” section for more Information on these status bits.
When the Embedded Erase algorithm is complete, the device
returns to reading array data and addresses are no longer
latched. See the Erase/Program Operations tables in “AC
Characteristics” for parameters.
Sector Erase Command
Sector erase is a six-bus cycle operation. The sector erase
command sequence is initiated by writing two unlock cycles,
followed by a set-up command. Two additional unlock write
cycles are then followed by the address of the sector to be
erased, and the sector erase command.
The device does not require the system to preprogram the
memory prior to erase. The Embedded Erase algorithm
automatically programs and verifies the sector for an all zero
data pattern prior to electrical erase. The system is not
required to provide any controls or timings during these
operations.
After the command sequence is written, a sector erase
time-out of 50 µs begins. Driving the time-out period,
additional sector addresses and sector erase commands may
be written. Loading the sector erase buffer may be done in
any sequence, and the number of sectors may be from one
sector to all sectors. The time between these additional
cycles must be less than 50 s, otherwise the last address and
command might not be accepted, and erasure may begin.
It is recommended that processor interrupts be disabled
during this time to ensure all commands are accepted. The
interrupts can be re-enabled after the last Sector Erase
command is written. If the time between additional sector
erase commands can be assumed to be less than 50 µs, the
system need not monitor DQ3.
Any command other than Sector Erase or Erase Suspend
during the time-out period resets the device to reading array
data. The system must rewrite the command sequence and
any additional sector addresses and commands.
The system can monitor DQ3 to determine if the sector erase
timer has timed out. (See the “DQ3: Sector Erase Timer”
section.) The time-out begins from the rising edge of the final
WE pulse in the command sequence.
Elite Semiconductor Memory Technology Inc.
F49L320UA/F49L320BA (2F)
Once the sector erase operation has begun, only the Erase
Suspend command is valid. All other commands are
ignored. Note that a hardware reset during the sector erase
operation immediately terminates the operation. The
Sector Erase command sequence should be reinitiated
once the device has returned to reading array data, to
ensure the data integrity.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are no
longer latched. The system can determine the status of the
erase operation by using DQ7, DQ6, DQ2, or RY/ BY .
(Refer to “Write Operation Status” section for more
information on these status bits.)
Refer to the Erase/Program Operations tables in the “AC
Characteristics” section for parameters.
Sector Erase Suspend/Resume Command
The Erase Suspend command allows the system to
interrupt a sector erase operation and then read data from,
or program data to, any sector not selected for erasure
(The device “ erase suspends” all sect or selected for
erasure.). This command is valid only during the sector
erase operation, including the 50 µs time-out period during
the sector erase command sequence. The Erase Suspend
command is ignored if written during the chip erase
operation or Embedded Program algorithm. Addresses are
“don’t -cares” when writing the Erase Suspend command
as shown in Table 5.
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum of
20µs to suspend the erase operation. However, when the
Erase Suspend command is written during the sector erase
time-out, the device immediately terminates the time-out
period and suspends the erase operation.
Reading at any address within erase-suspended sectors
produces status data on DQ7–DQ0. The system can use
DQ7, or DQ6 and DQ2 together, to determine if a sector is
actively erasing or is erase-suspended. See “Write
Operation Status” section for more information on these
status bits.
After an erase-suspended program operation is complete,
the system can once again read array data within
non-suspended sectors. The system can determine the
status of the program operation using the DQ7 or DQ6
Publication Date :
Revision: 1.0
Jul. 2012
18/57
ESMT
F49L320UA/F49L320BA (2F)
status bits, just as in the standard program operation. See
“Write Operation Status” f or more information.
The system may also write the auto-select command
sequence when the device is in the Erase Suspend mode.
The device allows reading auto-select codes even at
addresses within erasing sectors, since the codes are not
stored in the memory array. When the device exits the
auto-select mode, the device reverts to the Erase Suspend
mode, and is ready for another valid operation.
After an erase-suspended program operation is complete, the
system can once again read array data within non-suspended
sectors. The system can determine the status of the program
operation using the DQ7 or DQ6 status bits, just as in the
standard program operation. See “Write Operation Status” f or
more information.
The system may also write the auto-select command
sequence when the device is in the Erase Suspend mode.
The device allows reading auto-select codes even at
addresses within erasing sectors, since the codes are not
stored in the memory array. When the device exits the
auto-select mode, the device reverts to the Erase Suspend
mode, and is ready for another valid operation.
The system must write the Erase Resume command
(address bits are “don’t care” as shown in Table 5) to exit the
erase suspend mode and continue the sector erase
operation. Further writes of the Resume command are
ignored. Another Erase Suspend command can be written
after the device has resumed erasing.
Auto-select Command
The auto-select command sequence allows the host
system to access the manufacturer and devices codes,
and determine whether or not a sector is protected. Table 6
shows the address and data requirements. This method is
an alternative to that shown in Table 4, which is intended
for PROM programmers and requires VID on address bit
A9.
The auto-select command sequence is initiated by writing
two unlock cycles, followed by the auto-select command.
The device then enters the auto-select mode, and the
system may read at any address any number of times,
without initiating another command sequence. The read
cycles at address 04H, 08H, 0CH, and 00H retrieves the
ESMT manufacturer ID. A read cycle at address 01H
retrieves the device ID. A read cycle containing a sector
address(SA) and the address 02H returns 01H if that
sector is protected, or 00H if it is unprotected. Refer to
Tables 1 and 2 for valid sector addresses.
The system must write the reset command to exit the
auto-select mode and return to reading array data.
7.3 Write Operation Status
The device provides several bits to determine the status of a
write operation: RY/ BY , DQ7, DQ6, DQ5, DQ3, DQ2, and.
Table 7 and the following subsections describe the functions
of these bits. RY/ BY , DQ7, and DQ6 each offer a method for
determining whether a program or erase operation is
complete or in progress.
Table 7: Write Operation Status
Status
Embedded Program Algorithm
In Progress
Exceeded
Time Limits
DQ7
(Note1)
DQ6
DQ5
DQ3
(Note2)
DQ7
Toggle
0
N/A
0
Toggle
No
Toggle
0
1
No
Toggle
Toggle
0
N/A
Toggle
1
DQ2
RY/ BY
0
Embedded Erase Algorithm
Reading Erase Suspended
Sector
Erase Suspended Mode Reading Non-Erase
Suspended Sector
Erase Suspend Program
Data
Data
Data
Data
Data
1
DQ7
Toggle
0
N/A
0
Embedded Program Algorithm
DQ7
Toggle
1
N/A
Embedded Erase Algorithm
Erase Suspend Program
0
DQ7
Toggle
Toggle
1
1
1
N/A
N/A
No
Toggle
Toggle
N/A
1
0
0
0
0
Notes:
1. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
2. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.
See “DQ5: Exceeded Timing Limits” for more information.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
19/57
ESMT
F49L320UA/F49L320BA (2F)
RY/ BY :
Ready/Busy
Timings (During Embedded Algorithms), Figure 20 shows
the Data Polling algorithm.
The RY/ BY is a dedicated, open-drain output pin that
indicates whether an Embedded Algorithm is in progress or
complete. The RY/ BY status is valid after the rising edge of
the final WE pulse in the command sequence. Since RY/ BY
is an open-drain output, several RY/ BY pins can be tied
together in parallel with a pull-up resistor to VCC.
DQ6:Toggle BIT I
If the output is low (Busy), the device is actively erasing or
programming. (This includes programming in the Erase
Suspend mode.) If the output is high (Ready), the device is
ready to read array data (including during the Erase Suspend
mode), or is in the standby mode. Table 7 shows the outputs
for RY/ BY .
DQ7: Data Polling
The DQ7 indicates to the host system whether an Embedded
Algorithm is in progress or completed, or whether the device
is in Erase Suspend mode. The Data Polling is valid after the
rising edge of the final WE pulse in the program or erase
command sequence.
During the Embedded Program algorithm, the device outputs
on DQ7 the complement of the datum programmed to DQ7.
This DQ7 status also applies to programming during Erase
Suspend. When the Embedded Program algorithm is
complete, the device outputs the true data on DQ7. The
system must provide the program address to read valid status
information on DQ7. If a program address falls within a
protected sector, Data Polling on DQ7 is active for
approximately 1 µs, then the device returns to reading array
data.
During the Embedded Erase algorithm, Data Polling produces
a “0” on DQ7. When the Embedded Erase algorithm is
complete, or if the device enters the Erase Suspend mode,
Data Polling produces a “1” on DQ7. The system must
provide an address within any of the sectors selected for
erasure to read valid status information on DQ7.
After an erase command sequence is written, if all sectors
selected for erasing are protected, Data Polling on DQ7 is
active for approximately 100 µs, then the device returns to
reading array data. If not all selected sectors are protected,
the Embedded Erase algorithm erases the unprotected
sectors, and ignores the selected sectors that are protected.
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7~DQ0
on the following read cycles. This is because DQ7 may
change asynchronously with DQ0–DQ6 while Output Enable
( OE ) is asserted low. Refer to Figure 22, Data Polling
Elite Semiconductor Memory Technology Inc.
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete, or
whether the device has entered the Erase Suspend mode.
Toggle Bit I may be read at any address, and is valid after
the rising edge of the final WE pulse in the command
sequence (prior to the program or erase operation), and
during the sector erase time-out.
During an Embedded Program or Erase algorithm
operation, successive read cycles to any address cause
DQ6 to toggle. The system may use either OE or CE to
control the read cycles. When the operation is complete,
DQ6 stops toggling.
When an erase command sequence is written, if all
sectors selected for erasing are protected, DQ6 toggles
for approximately 100 µs, then returns to reading array
data. If not all selected sectors are protected, the
Embedded Erase algorithm erases the unprotected
sectors, and ignores the selected sectors that are
protected.
The system can use DQ6 and DQ2 together to determine
whether a sector is actively erasing or is
erase-suspended. When the device is actively erasing (i.e.
the Embedded Erase algorithm is in progress), DQ6
toggles. When the device enters the Erase Suspend
mode, DQ6 stops toggling. However, the system must
also use DQ2 to determine which sectors are erasing or
erase-suspended. Alternatively, the system can use DQ7.
If a program address falls within a protected sector, DQ6
toggles for approximately 2µs after the program command
sequence is written, then returns to reading array data.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded Program
algorithm is complete. Table 7 shows the outputs for
Toggle Bit I on DQ6. Figure 21 shows the toggle bit
algorithm. Figure 23 shows the toggle bit timing diagrams.
Figure 27 shows the differences between DQ2 and DQ6 in
graphical form. Refer to the subsection on DQ2: Toggle Bit
II.
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates
whether a particular sector is actively erasing (that is, the
Embedded Erase algorithm is in progress), or whether that
sector is erase-suspended. Toggle Bit II is valid after the
rising edge of the final or CE , whichever happens first, in
the command sequence.
Publication Date :
Revision: 1.0
Jul. 2012
20/57
ESMT
DQ2 toggles when the system reads at addresses within
those sectors that have been selected for erasure. (The
system may use either OE or CE to control the read
cycles.) But DQ2 cannot distinguish whether the sector is
actively erasing or is erase-suspended.
DQ6, by comparison, indicates whether the device is actively
erasing, or whether is in erase-suspended, but cannot
distinguish which sectors are selected for erasure. Thus, both
status bits are required for sector and mode information.
Refer to Table 7 to compare outputs for DQ2 and DQ6.
Figure 21 shows the toggle bit algorithm in flowchart form.
See also the DQ6: Toggle Bit I subsection. Figure 23 shows
the toggle bit timing diagram. Figure 27 shows the differences
between DQ2 and DQ6 in graphical form.
Reading Toggle Bits DQ6/ DQ2
Refer to Figure 21 for the following discussion. Whenever the
system initially begins reading toggle bit status, it must read
DQ7–DQ0 at least twice in a row to determine whether a
toggle bit is toggling. Typically, the system would note and
store the value of the toggle bit after the first read. After the
second read, the system would compare the new value of the
toggle bit with the first. If the toggle bit is not toggling, the
device has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the following
read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the system
should note whether the value of DQ5 is high (see the section
on DQ5). If it is, the system should then determine again
whether the toggle bit is toggling, since the toggle bit may
have stopped toggling just as DQ5 went high. If the toggle bit
is no longer toggling, the device has successfully completed
the program or erase operation. If it is still toggling, the device
did not completed the operation successfully, and the system
must write the reset command to return to reading array data.
The remaining scenario is that the system initially determines
that the toggle bit is toggling and DQ5 has not gone high. The
system may continue to monitor the toggle bit and DQ5
through successive read cycles, determining the status as
described earlier. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the
beginning of the algorithm when it returns to determine the
status of the operation.
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
Elite Semiconductor Memory Technology Inc.
F49L320UA/F49L320BA (2F)
exceeded the specified limits(internal pulse count). Under
these conditions DQ5 will produce a "1". This time-out
condition indicates that the program or erase cycle was
not successfully completed. Data Polling and Toggle Bit
are the only operating functions of the device under this
condition.
If this time-out condition occurs during sector erase
operation, it specifies that a particular sector is bad and it
may not be reused. However, other sectors are still
functional and may be used for the program or erase
operation. The device must be reset to use other sectors.
Write the Reset command sequence to the device, and
then execute program or erase command sequence. This
allows the system to continue to use the other active
sectors in the device.
If this time-out condition occurs during the chip erase
operation, it specifies that the entire chip is bad or
combination of sectors are bad.
If this time-out condition occurs during the programming
operation, it specifies that the sector containing that byte is
bad and this sector may not be reused, however other
sectors are still functional and can be reused.
The time-out condition will not appear if a user tries to
program a non blank location without erasing. Please note
that this is not a device failure condition since the device
was incorrectly used.
DQ3:Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer does
not apply to the chip erase command.) If additional sectors
are selected for erasure, the entire timeout also applies
after each additional sector erase command.
When the time-out is complete, DQ3 switches from “ 0” to
“ 1.” If the time between additional sector erase commands
from the system can be assumed to be less than 50 µs,
the system need not monitor DQ3.
When the sector erase command sequence is written, the
system should read the status on DQ7 (Data Polling) or
DQ6 (Toggle Bit I) to ensure the device has accepted the
command sequence, and then read DQ3. If DQ3 is “ 1”,
the internally controlled erase cycle has begun; all further
commands (except Erase Suspend) are ignored until the
erase operation is complete.
If DQ3 is “0”, the device will accept additional sector erase
commands. To ensure the command has been accepted,
the system software should check the status of DQ3 prior
to and following each subsequent sector erase command.
If DQ3 is high on the second status check, the last
command might not have been accepted. Table 7 shows
the outputs for DQ3.
Publication Date :
Revision: 1.0
Jul. 2012
21/57
ESMT
F49L320UA/F49L320BA (2F)
Customer Lockable : Secured Silicon Sector NOT
Programmed or Protected at the Factory
Factory Locked : Secured Silicon Sector
Programmed and Protected at the Factory
The customer lockable version allows the Secured Silicon
Sector to be programmed once, and then permanently locked
after it ships. Note that the accelerated programming (ACC) is
not available when programming the Secured Silicon Sector.
The Secured Silicon Sector feature provides a 256 –byte
Flash memory region that enables permanent part
identification through an Electronic Serial Number (ESN).
The Secured Silicon Sector uses a Secured Silicon Sector
Indicator Bit (DQ7) to indicate whether or not the Secured
Silicon Sector is locked when shipped from the factory.
Factory Locked version the Bit (DQ7) set to 1, Customer
Lockable version the Bit (DQ7) set to 0.
The Secured Silicon Sector area can be protected using the
following procedures:
„
Write the three-cycle Enter Secured silicon Region
command sequence, and then follow the in-system
sector group protect algorithm as shown in Figure 17.
of page41, except that RESET may be either VIH or
VID. This allows in system protection of the Secured
Silicon Sector without raising any device pin to a high
voltage. Note that this method is only applicable to the
Secured silicon Sector.
„
To verify the protect/unprotect status of the Secured
Silicon Sector, follow the algorithm shown in below
table.
Once the Secured Silicon Sector protection must be used
with caution since, once protected, there is no procedure
available for unprotecting the Secured silicon Sector area,
and none of the bits in the Secured Silicon Sector memory
space can be modified in any way.
In a factory locked device, the Secured Silicon Sector
cannot be modified in any way. The device is available
pre-programmed with one of the following:
1.
2.
3.
A random, secure ESN only.
Customer code through the Express Flash service.
Both a random, secure ESN and customer code
through the Express Flash device.
In device that have an ESN, a Bottom Boot device has the
16-byte (8-word) ESN in sector 0 at address
00000H-0000FH in byte mode(or 00000H~00007H in
word mode).In the Top Boot device, the ECN is in sector
70 at addresses 3FFF00h-3FFF0Fh in byte mode ( or
1FFF80h-1FFF87h in word mode). In the uniform device,
the ESN is in sector 63 at addresses 3FFF00h-3FFF0Fh in
byte mode (or 1FFF80h- 1FFF87h in word mode).
Customers may opt to have their code programmed by
ESMT through the Express-Flash service. ESMT
programs the customer’s code, with or without the random
ESN. The devices are then shipped from the ESMT factory
with the Secured Silicon Sector locked.
Note:
Elite Semiconductor Memory Technology Inc.
1.
After entering Secured Silicon Sector mode, user can
program Secured Silicon Sector (means to write ESN
code) and do Secured Silicon Sector protection once
when device is customer lockable version.
2.
Enter Secured Silicon Sector mode, the under
functions are not allowed except for CFI.
a. Sector Erase/Erase Suspend/Resume.
b. Chip Erase.
3.
Secured Silicon Sector mode doesn’t have “Erase”
and “Unprotect” function.
Publication Date :
Revision: 1.0
Jul. 2012
22/57
ESMT
F49L320UA/F49L320BA (2F)
Upper Boot Device Secured Silicon Sector Addresses
Sector Address
A20~12
Sector Size
( bytes/words)
( x8 )
Address Range
( x16 )
Address Range
111111111
256/128
3FFF00h-3FFFFFh
1FFF80h-1FFFFFh
Bottom Boot Device Secured Silicon Sector Addresses
Sector Address
A20~12
Sector Size
( bytes/words)
( x8 )
Address Range
( x16 )
Address Range
000000000
256/128
000000h-0000FFh
000000h-00007Fh
7.4 More Device Operations
Hardware Data Protection
Logical Inhibit
The command sequence requirement of unlock cycles for
programming or erasing provides data protection against
inadvertent writes. In addition, the following hardware data
protection measures prevent accidental erasure or
programming, which might otherwise be caused by spurious
system level signals during VCC power-up and power-down
transitions, or from system noise.
Write cycles are inhibited by holding any one of OE = VIL,
CE = VIH or WE = VIH. To initiate a write cycle, CE and
Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any
write cycles. This protects data during VCC power-up and
power-down. The command register and all internal
program/erase circuits are disabled, and the device resets.
Subsequent writes are ignored until VCC is greater than VLKO.
The system must provide the proper signals to the control
pins to prevent unintentional writes when VCC is greater than
VLKO.
Write Pulse "Glitch" Protection
Noise pulses of less than 5 ns (typical) on CE or WE do
not initiate a write cycle.
Elite Semiconductor Memory Technology Inc.
WE must be a logical zero while OE is a logical one.
Power Supply Decoupling
In order to reduce power switching effect, each device
should have a 0.1uF ceramic capacitor connected between
its VCC and GND.
Power-Up Sequence
The device powers up in the Read Mode. In addition, the
memory contents may only be altered after successful
completion of the predefined command sequences.
Power-Up Write Inhibit
If WE = CE = VIL and OE = VIH during power up, the
device does not accept commands on the rising edge of
WE . The internal state machine is automatically reset to
reading array data on power-up.
Publication Date :
Revision: 1.0
Jul. 2012
23/57
ESMT
F49L320UA/F49L320BA (2F)
8. COMMON FLASH MEMORY INTERFACE (CFI)
The Common Flash Interface (CFI) specification outlines
device and host system software interrogation handshake,
which allows specific vendor-specified software algorithms
to be used for entire families of devices. Software support
can then be device-independent, JEDEC ID-independent,
and forward- and backward- compatible for the specified
flash device families. Flash vendors can standardize their
existing interfaces for long-term compatibility.
This device enters the CFI Query mode when the system
writes the CFI Query command, 98h, to address 55h in
word mode (or address AAh in byte mode), any time the
device is ready to array data. The system can read CFI
information at the address given in Tables 8-10 in word
mode, the upper address bits (A7-MSB) must be all zeros.
To terminate reading CFI data, the system must write the
reset command.
The system can also write the CFI query command when the
device is in the autoselect mode. The device enters the CFI
query mode, and the system can read CFI data at the
addresses given in Tables 8-10. The system must write the
reset command to return the device to the autoselect mode.
Table 8: CFI Query Identification String
Addresses
(Word Mode)
Address
(Byte Mode)
Data
10h
11h
12h
20h
22h
24h
0051h
0052h
0059h
Query Unique ASCII string “QRY”
13h
14h
26h
28h
0002h
0000h
Primary OEM Command Set
15h
16h
2Ah
2Ch
0040h
0000h
Address for Primary Extended Table
17h
18h
2Eh
30h
0000h
0000h
Alternate OEM Command Set (00h = none exists)
19h
1Ah
32h
34h
0000h
0000h
Address for Alternate OEM Extended Table (00h = none exists)
Description
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
24/57
ESMT
F49L320UA/F49L320BA (2F)
Table 9: System Interface String
Addresses
(Word Mode)
Address
(Byte Mode)
Data
1Bh
36h
0027h
1Ch
38h
0036h
1Dh
3Ah
0000h
VCC Min. (write/erase)
D7~D4 : volt, D3~D0 : 100 millivolt
VCC Max. (write/erase)
D7~D4 : volt, D3~D0 : 100 millivolt
VPP Min. voltage (00h = no VPP pin present)
1Eh
3Ch
0000h
VPP Max. voltage (00h = no VPP pin present)
1Fh
3Eh
0004h
Typical timeout per single byte/word write 2N μs
20h
40h
0000h
Typical timeout for Min. size buffer write 2N μs (00h = not supported)
21h
42h
000Ah
Typical timeout per individual block erase 2N ms
22h
44h
0000h
Typical timeout for full chip erase 2N ms (00h = not supported)
23h
46h
0005h
Max. timeout for byte/word write 2N word times typical
24h
48h
0000h
Max. timeout for buffer write 2N word times typical
25h
4Ah
0004h
Max. timeout per individual block erase 2N word times typical
26h
4Ch
0000h
Max. timeout per full chip erase 2N word times typical (00h = not supported)
Description
Table 10: Device Geometry Definition
Addresses
(Word Mode)
Address
(Byte Mode)
Data
27h
28h
29h
2Ah
2Bh
2Ch
2Dh
2Eh
2Fh
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
3Ah
3Bh
3Ch
4Eh
50h
52h
54h
56h
58h
5Ah
5Ch
5Eh
60h
62h
64h
66h
68h
6Ah
6Ch
6Eh
70h
72h
74h
76h
78h
0016h
0002h
0000h
0000h
0000h
0002h
0007h
0000h
0020h
0000h
003Eh
0000h
0000h
0001h
0000h
0000h
0000h
0000h
0000h
0000h
0000h
0000h
Description
Device Size = 2N byte
Flash Device Interface description (refer to CFI publication 100)
Max. number of byte in multi-byte write = 2N
(00h = not supported)
Number of Erase Block Regions within device
Erase Block Region 1 Information
(refer to the CFI specification or CFI publication 100)
Erase Block Region 2 Information
Erase Block Region 3 Information
Erase Block Region 4 Information
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
25/57
ESMT
F49L320UA/F49L320BA (2F)
Table 11: Primary Vendor-Specific Extended Query
Addresses
(Word Mode)
Address
(Byte Mode)
Data
40h
41h
42h
43h
80h
82h
84h
86h
0050h
0052h
0049h
0031h
44h
88h
0031h
45h
8Ah
0000h
46h
8Ch
0002h
47h
8Eh
0004h
48h
90h
0001h
49h
92h
0004h
4Ah
94h
0000h
4Bh
96h
0000h
4Ch
98h
0002h
4Dh
9Ah
00B5h
4Eh
9Ch
00C5h
4Fh
9Eh
000Xh
Description
Query-unique ASCII string “ PRI”
Major version number, ASCII
Minor version number, ASCII
Address Sensitive Unlock
0 = Required, 1 = Not Required
Erase Suspend
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
Erase Protect
0 = Not Supported, X = Number of sectors in per group
Sector Group Temporary Unprotect
00 = Not Supported, 01 = Supported
Sector Group Protect/Chip Unprotect scheme
Simultaneous Operation
00 = Not Supported, 01 = Supported
Burst Mode Type
00 = Not Supported, 01 = Supported
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
ACC (Acceleration) Supply Minimum
00h = Not Supported, D7-D4 : Volt, D3-D0 : 100mV
ACC (Acceleration) Supply Maximum
00h = Not Supported, D7-D4 : Volt, D3-D0 : 100mV
Top / Bottom Boot Sector Flag
(02h = Bottom Boot device, 03h = Top Boot Device)
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
26/57
ESMT
F49L320UA/F49L320BA (2F)
9. ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . . . –65°C to +150°C
Ambient Temperature
with Power Applied. . . . . . . .. . . . . . . –65°C to +125°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . –0.5 V to +4.0 V
A9, OE , and RESET (Note 2) . . . –0.5 V to +10.5V
All other pins (Note 1). . . . . . . . . . –0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) .. . .. 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is –0.5 V. During
voltage transitions, input or I/O pins may overshoot VSS
to –2.0 V for periods of up to 20 ns. See Figure 1.
Maximum DC voltage on input or I/O pins is VCC +0.5 V.
During voltage transitions, input or I/O pins may overshoot
to VCC +2.0 V for periods up to 20 ns. See Figure 2.
2. Minimum DC input voltage on pins A9, OE , and RESET
is -0.5 V. During voltage transitions, A9, OE , and
RESET may overshoot VSS to –2.0 V for periods of up to
20 ns. See Figure 1. Maximum DC input voltage on pin A9
is +10.5V which may overshoot to 14V periods up to 20
ns.
3. No more than one output may be shorted to ground at a
time. Duration of the short circuit should not be greater
than one second.
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This
is a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating
conditions for extended periods may affect device reliability.
Figure 1. Maximum Negative Overshoot Waveform
20 n s
20 n s
+0.8V
-0.5V
-2.0V
20 n s
Figure 2. Maximum Positive Overshoot Waveform
20 n s
Vc c
+2.0V
Vc c
+0.5V
2.0V
20 n s
Elite Semiconductor Memory Technology Inc.
20 n s
Publication Date :
Revision: 1.0
Jul. 2012
27/57
ESMT
F49L320UA/F49L320BA (2F)
10. OPERATING RANGES
Operating Temperature Ambient Temperature ( TA) . . . . . . . . . . . 0 °C to +70°C
VCC Supply Voltages VCC for all devices . . . . . . . . . . . . . . . . . . . . .2.7 V to 3.6 V
Operating ranges define those limits between which the functionality of the device is guaranteed.
Table 12: Capacitance TA = 25°C , f = 1.0 MHz
Symbol
Description
Conditions
CIN1
CIN2
COUT
Input Capacitance
Control Pin Capacitance
Output Capacitance
VIN = 0V
VIN = 0V
VOUT = 0V
Min.
Typ.
Max.
Unit
8
12
12
pF
pF
pF
11. DC CHARACTERISTICS
Table 13: DC Characteristics (TA = 0°C to 70°C, VCC = 2.7V to 3.6V)
Symbol
ILI
ILIT
ILO
ICC1
Description
Input Leakage Current
A9 Input Leakage Current
Output Leakage Current
VCC Active Read Current
ICC3
Typ.
Max.
Unit
±1
35
±1
uA
uA
uA
VIN = VSS or VCC, VCC = VCC max.
VCC = VCC max; A9=10.5V
VOUT = VSS or VCC, VCC = VCC max
CE = VIL, OE = VIH
( Byte Mode )
CE = VIL, OE = VIH
( Word Mode )
ICC2
Min.
Conditions
@5MHz
9
25
mA
@1MHz
2
5
mA
@5MHz
9
40
mA
@1MHz
2
5
mA
VCC Active write Current
CE = VIL, OE = VIH
20
50
mA
VCC Standby Current
CE ; RESET = VCC ± 0.3V
25
100
uA
RESET = VSS ± 0.3V
25
100
uA
ICC5
VCC Standby Current
During Reset
Automatic sleep mode
VIH = VCC ± 0.3V; VIL = VSS ± 0.3V
25
100
uA
ICC6
VCC Active Page Read Current
OE = VIH, 8 word Page Read
10
15
mA
IACC
ACC Accelerated Program
Current, Word or Byte
CE = VIL, OE = VIH
5
15
VIL
VIH
Input Low Voltage(Note 1)
Input High Voltage
-0.5
0.7x VCC
10
30
0.8
VCC + 0.3
mA
mA
V
V
10
10.5
V
0.45
V
V
V
V
ICC4
VID
VOL
VOH1
VOH2
VLKO
Voltage for WP /ACC (Write
Protect / Program Acceleration),
Auto-Select and Temporary
Sector Group Unprotect
Output Low Voltage
Output High Voltage(TTL)
Output High Voltage
Low VCC Lock-out Voltage
ACC pin
VCC pin
VCC =3.3V
IOL = 4.0mA, VCC = VCC min
IOH = -2mA, VCC = VCC min
IOH = -100uA, VCC min
0.7x VCC
VCC -0.4
2.3
2.5
Notes:
1. VIL min. = -1.0V for pulse width is equal to or less than 50 ns.
VIL min. = -2.0V for pulse width is equal to or less than 20 ns.
2. VIH max. = VCC + 1.5V for pulse width is equal to or less than 20 ns
If VIH is over the specified maximum value, read operation cannot be guaranteed.
3. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
28/57
ESMT
F49L320UA/F49L320BA (2F)
12. AC CHARACTERISTICS
TEST CONDITIONS
Figure 3. Test Setup
Figure 4. Input Waveforms and Measurement Levels
3.0V
0V
1.5V
1.5V
Test Poin t s
In p u t
Out pu t
A C TE S TIN G : In p u t s a r e d ri v e n a t 3 . 0 V f o r a l o g i c " 1 " a n d 0 V f o r a l o g i c " 0 "
In p u t p u l s e r i s e a n d f a l l t i m e s a r e < 5 n s .
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
29/57
ESMT
F49L320UA/F49L320BA (2F)
12.1 Read Operation
Table 14: Read Operations (TA = 0°C to 70°C, VCC = 2.7V~3.6V)
Symbol
Description
tRC
tACC
Read Cycle Time (Note 1)
Address to Output Delay
tCE
tPACC
tOE
tDF
tOEH
tOH
Conditions
-70
Min.
70
-90
Max.
Min.
90
Max.
Unit
CE = OE = VIL
70
90
ns
ns
CE to Output Delay
Page Access Time
OE = VIL
OE to Output Delay
CE = VIL
70
30
30
90
30
35
ns
ns
ns
OE High to Output Float
(Note2)
Output Enable Read
Toggle and
Hold Time
Data Polling
Address to Output hold
CE = VIL
25
30
ns
CE = OE = VIL
0
0
ns
10
10
ns
0
0
ns
Notes:
1. Not 100% tested.
2. tDF is defined as the time at which the output achieves the open circuit condition and data is no longer driven.
Figure 5. Read Timing Waveform
tRC
Addresses Stabl e
Addr es s
tAC C
CE
tDF
tOE
OE
tOEH
WE
tCE
tOH
High-Z
Ou t pu t s
High-Z
Output Vali d
RESET
RY/BY
0V
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
30/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 6. Page Read Operation Timings Waveform
Sam e Page
A20-A3
Aa
A2-A0
tACC
Data
Ab
Ac
tPACC
tPACC
Qa
Qb
Ad
tPACC
Qc
Qd
CE
OE
12.2 Program/Erase Operation
Table 15: WE Controlled Program/Erase Operations (TA = 0°C to 70°C, VCC = 2.7V~3.6V)
-70
-90
Unit
Symbol
Description
Min.
Max.
Min.
Max.
tWC
Write Cycle Time (Note 1)
70
90
ns
tAS
Address Setup Time
0
0
ns
tAH
Address Hold Time
45
45
ns
tDS
Data Setup Time
35
45
ns
tDH
Data Hold Time
0
0
ns
tOES
Output Enable Setup Time
0
0
ns
Read Recovery Time Before
tGHWL
0
ns
0
Write ( OE High to WE low)
0
tCS
0
ns
CE Setup Time
Hold
Time
tCH
0
ns
0
CE
tWP
Write Pulse Width
35
35
ns
tWPH
Write Pulse Width High
30
30
ns
Programming Operation
Byte
9(typ.)
9(typ.)
tWHWH1
us
(Note 2)
Word
11(typ.)
11(typ.)
Accelerated Programming Operation,
tWHWH1
8 (typ.)
8 (typ.)
us
Word or Byte (Note2)
tWHWH2
Sector Erase Operation (Note 2)
0.7(typ.)
0.7(typ.)
sec
tVCS
VCC Setup Time (Note 1)
50
50
us
0
0
ns
tRB
Recovery Time from RY/ BY
90
90
ns
tBUSY
Program/Erase Valid to RY/ BY Delay
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
31/57
ESMT
F49L320UA/F49L320BA (2F)
Table 16: CE Controlled Program/Erase Operations (TA = 0°C to 70°C, VCC = 2.7V~3.6V)
-70
-90
Symbol
Description
Unit
Min.
Max.
Min.
Max.
tWC
Write Cycle Time (Note 1)
70
90
ns
tAS
Address Setup Time
0
0
ns
tAH
Address Hold Time
45
45
ns
tDS
Data Setup Time
35
45
ns
tDH
Data Hold Time
0
0
ns
tOES
Output Enable Setup Time
0
0
ns
tGHEL
Read Recovery Time Before Write
0
0
ns
0
tWS
0
ns
WE Setup Time
0
tWH
0
ns
WE Hold Time
35
35
ns
tCP
CE Pulse Width
30
30
ns
tCPH
CE Pulse Width High
Byte
9 (typ.)
9 (typ.)
us
Programming Operation
tWHWH1
(Note2)
Word
11(typ.)
11(typ.)
us
Accelerated Programming Operation,
tWHWH1
8 (typ.)
8 (typ.)
us
Word or Byte (Note2)
tWHWH2
Sector Erase Operation (Note2)
0.7(typ.)
0.7(typ.)
sec
Notes:
1. Not 100% tested.
2. See the "Erase and Programming Performance" section for more information.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
32/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 7. Write Command Timing Waveform
VCC
Addr es s
3V
VIH
ADD Valid
VIL
tAH
tAS
VIH
WE
VIL
tOES
tWP
tWPH
tCW C
CE
VIH
VIL
tCS
OE
tCH
VIH
VIL
tDS
Dat a
VIH
VIL
Elite Semiconductor Memory Technology Inc.
tDH
DIN
Publication Date :
Revision: 1.0
Jul. 2012
33/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 8. Embedded Programming Timing Waveform
Pr ogr am C omm an d S equ en ce ( l as t t wo cycl e)
tAS
tWC
PA
PA
5 55 h
Addr es s
Read Stat us D at a ( last t w o cycl e)
PA
tAH
CE
tCH
tGHWL
OE
tW HW H1
tWP
WE
tWPH
tCS
tDS tDH
A0 h
Dat a
PD
St at u s
DOUT
tB US Y
tRB
RY/BY
tVCS
VCC
Notes:
1. PA = Program Address, PD = Program Data, DOUT is the true data the program address.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
34/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 9. Embedded Programming Algorithm Flowchart
Start
W rite Data AAH Address 555H
W rite Data 55H Address 2AAH
W rite Data A0H Address 555H
In c r e m e n t
address
W rite Program Data/Address
Data Poll
from system
No
Verify W ork OK?
Ye s
No
Last address?
Ye s
Embedded Program Completed
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
35/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 10. CE Controlled Program Timing Waveform
555 for prog ram PA f or p rog r am
2AA for erase
SA for sector erase
555 for ch ip eras e
Data Pol li n g
PA
Addr es s
tWC
tAS
tAH
tWH
WE
tG HEL
OE
tCP
tWHWH1
or 2
CE
tCPH
tWS
tBUSY
tDS
tDH
Dat a
DQ7 DOUT
tRH
A0 f o r p r og r a m PD f o r p r o g r a m
30 f or sect or erase
55 for erase
10 f or ch ip erase
RESET
RY/BY
Notes:
1. PA = Program Address, PD = Program Data, DOUT = Data Out, DQ7 = complement of data written to device
2. Figure indicates the last two bus cycles of the command sequence..
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
36/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 11. Embedded Chip Erase Timing Waveform
Read Statu s Dat a
Er as e Com mand Sequ en ce( last t w o cycl e)
tAS
tWC
5 55 h
2AAh
Addr es s
VA
VA
tAH
CE
tCH
tGHWL
OE
tW HW H2
tWP
WE
tWPH
tCS
tDS tDH
5 5h
Dat a
In
Progress Complete
1 0h
tBUSY
tRB
RY/BY
tVCS
VCC
Notes:
SA = Sector Address (for Sector Erase), VA = Valid Address for reading status data (see "Write Operation Status").
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
37/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 12. Embedded Chip Erase Algorithm Flowchart
Start
W rite Data AAH Address 555H
W rite Data 55H Address 2AAH
W rite Data 80H Address 555H
W rite Data AAH Address 555H
W rite Data 55H Address 2AAH
W rite Data 10H Address 555H
Data Poll from System
No
Data = FFh?
Ye s
Embedded Chip Erease Completed
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
38/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 13. Embedded Sector Erase Timing Waveform
Read Statu s Dat a
Er as e Com mand Sequ en ce( last t w o cycl e)
tAS
tWC
SA
2AAh
Addr es s
VA
VA
tAH
CE
tCH
tGHWL
OE
tW HW H2
tWP
WE
tWPH
tCS
tDS tDH
55 h
Dat a
In
Progress Complete
3 0h
tBUSY
tRB
RY/BY
tVCS
VCC
Notes:
SA = Sector Address (for Sector Erase), VA = Valid Address for reading status data (see "Write Operation Status").
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
39/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 14. Embedded Sector Erase Algorithm Flowchart
Start
W rite Data AAH Address 5 55H
W rite Data 55 H Address 2AAH
W rite Data 80H Address 555H
W rite Data AAH Add ress 555H
W rit e Data 55H Address 2AAH
W rite Data 3 0H Address SA
Last Sector
to Erase
No
Yes
Data Po ll fro m System
No
Data = FFH?
Embedde d Sector Ere ase Co mplete d
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
40/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 15. Erase Suspend/Erase Resume Flowchart
Start
W rite Data B0H
Tog gle Bi t c h ec kin g Q 6
not toggled
No
ERASE SUSPEND
Ye s
Read Array or
Program
Readi ng or
Pr og r am m in g En d
No
Ye s
W rite Data 30H
ERASE RESUME
Continue Erase
An oth er
Er ase Suspend?
No
Ye s
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
41/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 16. In-System Sector Group Protect/ Chip Unprotect Timing Waveform ( RESET Control)
VID
VIH
RESET
SA,A 6
A1,A0
Valid*
Valid*
Sec t or P r ot ec t Sec tor U npr ot ec t
60 h
Dat a
1us
6 0h
Vali d*
Ver if y
St at u s
4 0h
Sector Protect = 150us
Sec t or Un p r ot ect = 15m s
CE
WE
OE
Notes:
When sector group protect, A6=0, A1=1, A0=0.
When chip unprotect, A6=1, A1=1, A0=0.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
42/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 17. In-System Sector Group Protect/ Chip Unprotect Algorithm ( RESET = VID)
Start
Start
PLSCNT = 1
PLSCNT = 1
Protect all sector :
The indicated portion
of the sector protect
algorithm must be
performed for all
unprotected sectors
prior to issuing the
first sector
unprotect address
RESET = V I D
W ait 1μ s?
Temporary Sector
Unprotect Mode
No
RESET = V I D
W ait 1μ s?
First W rite
Cyc le = 6 0 h ?
No
First W rite
Cyc le = 6 0 h ?
Ye s
Ye s
Set up sector
address
No
Al l s ec t o r s
pr otected ?
Ye s
Sector Protect :
W rite 60h to sector
address with
A6 = 0, A1 = 1,
A0 = 0
Set up first
sector address
W ait 150 μ s?
Sector Unprotect :
W rite 60h to sector
address with
A6 = 1, A1 = 1,
A0 = 0
Verify Sector
Protect : W rite 40h
to sector address
with A6 = 0,
A1 = 1, A0 = 0
In c r e m e n t
PL SC NT
Temporary Sector
Unprotect Mode
Reset
PLSCNT = 1
Read from
sector address
with A6 = 0,
A1 = 1, A0 = 0
W ait 15 ms?
Verify Sector
Unprotect : W rite
40h to sector
address with
A6 = 1, A1 = 1,
A0 =0
In c r e m e n t
PL SC NT
No
PLSCNT = 25?
Ye s
Dev ice failed
No
Data = 01h?
Read from
sector address
with A6 = 1,
A1 = 1, A0 =0
Ye s
Protect another
s e c to r ?
Ye s
No
Remove V I D
from RESET
W rite reset
command
Set up
next sector
address
No
PLSCNT
= 1000?
No
Data = 00h?
Ye s
Ye s
Dev ice failed
Last sector
v erified ?
No
Ye s
Sector Protect
Algorithm
Sector Protect
c o m p le te
Sector Unprotect
Algorithm
Remove V I D
from RESET
W rite reset
command
Sector Protect
c o m p le te
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
43/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 18. Sector Group Protect Timing Waveform (A9, OE Control)
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
44/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 19. Sector Group Protection Algorithm (A9, OE Control)
Start
Set up sector address
PLSCNT = 1
OE = V ID , A9 = V ID , CE = V I L
A6 = V IL
Activ ate W E Pluse
Time out 150us
Set W E = V I H , CE = OE = V I L
A9 should remain V I D
Read from Sector
Address = SA, A0=1, A1 = 1
No
No
PLSCNT = 32?
Data = 01H?
Ye s
Dev ice Failed
Ye s
Protect Another
Sector?
Remov e VID from A9
W rite reset command
Sector Protection
C o m p l e te
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
45/57
ESMT
F49L320UA/F49L320BA (2F)
WRITE OPERATION STATUS
Figure 20. Data Polling Algorithm
Start
Read DQ7~DQ0
Add. = VA(1)
Ye s
DQ7 = Data?
No
No
D Q5 = 1?
Ye s
Read DQ7~DQ0
Add. = VA
Ye s
DQ7 = Data?
(2 )
No
FAIL
Pass
Notes:
1. VA =Valid address for programming.
2. DQ7 should be re-checked even DQ5 = "1" because DQ7 may change simultaneously with DQ5.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
46/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 21. Toggle Bit Algorithm
Start
Read DQ7 ~ DQ0
Read DQ7 ~ DQ0
Toggle Bit = DQ6
Toggle?
(Note 1)
No
Ye s
No
D Q 5 = 1?
Ye s
Re ad D Q7 ~D Q 0 Tw ice
Toggle bit D Q6
= Tog gle?
(Note 1,2)
No
Ye s
Program / Erase operation
Not complete, write
reset command
Program / Erase
operation complete
Notes:
1. Read toggle bit twice to determine whether or not it is toggle.
2. Recheck toggle bit because it may stop toggling as DQ5 change to "1".
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
47/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 22. Data Polling Timings (During Embedded Algorithms)
tRC
Addr es s
VA
VA
tAC C
tCE
CE
tCH
tOE
OE
tOEH
tDF
WE
tO H
High-Z
DQ7
Complement
Complement
Tr u e
Vai l d Dat a
DQ0~DQ6
Statu s Data
Statu s Data
Tr u e
Vai l d Dat a
High-Z
tB US Y
RY/BY
Notes:
VA = Valid Address. Figure shows first status cycle after command sequence, last status read cycle, and array data read
cycle.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
48/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 23. Toggle Bit Timing Waveforms (During Embedded Algorithms)
tRC
VA
Addr es s
VA
VA
VA
tAC C
tCE
CE
tCH
tOE
OE
tOEH
tDF
WE
tOH
DQ6/DQ2
High-Z
tBUSY
Vai ld
Status
(fi rst re ad )
Vaild
Status
(sec ond read )
Vai ld D ata
Vaild D ata
(stops tog gling )
RY/BY
Notes:
VA = Valid Address; not required for DQ6. Figure shows first status cycle after command sequence, last status read cycle,
and array data read cycle.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
49/57
ESMT
F49L320UA/F49L320BA (2F)
12.3 Hardware Reset Operation
Table 17: AC CHARACTERISTICS
Symbol
Description
tRH
RESET Pin Low (During Embedded Algorithms)
to Read or Write (See Note)
RESET Pin Low (NOT During Embedded
Algorithms) to Read or Write (See Note)
RESET Pulse Width (During Embedded
Algorithms)
RESET High Time Before Read(See Note)
tRB
RY/ BY Recovery Time(to CE , OE go low)
tREADY1
tREADY2
tRP
All Speed Options
Unit
Max
20
us
Max
500
ns
Min
500
ns
Min
50
ns
Min
0
ns
Notes:
Not 100% tested
Figure 24. RESET Timing Waveform
RY/BY
CE, OE
tRH
RESET
tRP
tREA DY2
Reset Timing NOT during Automatic Algorithms
tREA DY1
RY/BY
tRB
CE, OE
RESET
tRP
Re set Tim ing du ring Auto matic Algo rithm s
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
50/57
ESMT
F49L320UA/F49L320BA (2F)
12.4 Temporary Sector Group Unprotect Operation
Table 18: Temporary Sector Group Unprotect
Symbol
All Speed Options
Unit
Min
500
ns
Min
4
us
Description
tVIDR
VID Rise and Fall Time (See Note)
RESET Setup Time for Temporary Sector Group
tRSP
Unprotect
Notes: Not 100% tested
Figure 25. Temporary Sector Group Unprotect Timing Diagram
12V
10
RESET
0 or VCC
0 or VCC
tVIDR
tVIDR
Program or Er ase Com man d Seq uence
CE
WE
tRSP
RY/BY
Figure 26. Accelerated Program Timing Diagram
VID
WP/ACC
VIL or VIH
VIL or VIH
tVIDR
tVIDR
Figure 27. DQ6 vs DQ2 for Erase and Erase Suspend Operations
En ter E m bedde d
Er as in g
Er as e
S u s pe n d
WE
Enter Eras e
Suspend Program
Er as e
Su s pen d
Pr ogr am
Er as e
Resume
Er as e
Su s pen d
Read
Er as e
Er as e
Com pl et e
DQ6
DQ2
Notes:
The system can use OE or CE to toggle DQ2 / DQ6, DQ2 toggles only when read at an address within an erase-suspended.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
51/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 28. Temporary Sector Group Unprotect Algorithm
Start
RESET = V ID (Note 1)
Program Erase or Program Operation
Operation Completed
RESET = V I H
Temporary Sector Unprotect Completed (Note 2)
Notes:
1. All protected status are temporary unprotect.
VID = 10V~10.5V
2. All previously protected sectors are protected again.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
52/57
ESMT
F49L320UA/F49L320BA (2F)
Figure 29. ID Code Read Timing Waveform
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
53/57
ESMT
F49L320UA/F49L320BA (2F)
13. ERASE AND PROGRAMMING PERFORMANCE
Table 19: Erase and Programming Performance (Note.1)
Limits
Parameter
Unit
Typ.(2)
Max.(3)
Sector Erase Time
0.7
15
sec
Chip Erase Time
25
50
sec
Byte Programming Time
9
300
us
Word Programming Time
11
360
us
Accelerated Byte/Word Programming Time
8
210
us
Byte Mode
36
108
sec
Word Mode
24
72
sec
Chip Programming Time
Erase/Program Cycles (1)
Data Retention
100,000
cycles
20
years
Notes:
1.Not 100% Tested, Excludes external system level over head.
2.Typical values measured at 25 ° C, 3.3V.
3.Maximum values measured at 85° C, 2.7V.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
54/57
ESMT
F49L320UA/F49L320BA (2F)
14. PACKAGE DIMENSION
48-LEAD
Symbol
A
A1
A2
b
b1
c
c1
TSOP(I) ( 12x20 mm )
Dimension in mm
Min Norm Max
------- ------- 1.20
0.05 ------- 0.15
0.95 1.00
1.05
0.17 0.22
0.27
0.17 0.20
0.23
0.10 ------- 0.21
0.10 ------- 0.16
Dimension in inch
Dimension in mm
Symbol
Min Norm Max
Min Norm Max
------- ------- 0.047
D
20.00 BSC
0.006 ------- 0.002
D1
18.40 BSC
0.037 0.039 0.041
E
12.00 BSC
0.007 0.009 0.011
0.50 BSC
e
0.007 0.008 0.009
L
0.50 0.60
0.70
0.004 ------- 0.008
θ
0O
------8O
0.004 ------- 0.006
Elite Semiconductor Memory Technology Inc.
Dimension in inch
Min Norm Max
0.787 BSC
0.724 BSC
0.472 BSC
0.020 BSC
0.020 0.024 0.028
0O
------8O
Publication Date :
Revision: 1.0
Jul. 2012
55/57
ESMT
F49L320UA/F49L320BA (2F)
Revision History
Revision
Date
0.1
2010.09.06
Original
1.0
2012.07.02
1. Delete "Preliminary"
2. Add page read mode
Elite Semiconductor Memory Technology Inc.
Description
Publication Date :
Revision: 1.0
Jul. 2012
56/57
ESMT
F49L320UA/F49L320BA (2F)
Important Notice
All rights reserved.
No part of this document may be reproduced or duplicated in any form or
by any means without the prior permission of ESMT.
The contents contained in this document are believed to be accurate at
the time of publication. ESMT assumes no responsibility for any error in
this document, and reserves the right to change the products or
specification in this document without notice.
The information contained herein is presented only as a guide or
examples for the application of our products. No responsibility is
assumed by ESMT for any infringement of patents, copyrights, or other
intellectual property rights of third parties which may result from its use.
No license, either express , implied or otherwise, is granted under any
patents, copyrights or other intellectual property rights of ESMT or
others.
Any semiconductor devices may have inherently a certain rate of failure.
To minimize risks associated with customer's application, adequate
design and operating safeguards against injury, damage, or loss from
such failure, should be provided by the customer when making
application designs.
ESMT's products are not authorized for use in critical applications such
as, but not limited to, life support devices or system, where failure or
abnormal operation may directly affect human lives or cause physical
injury or property damage. If products described here are to be used for
such kinds of application, purchaser must do its own quality assurance
testing appropriate to such applications.
Elite Semiconductor Memory Technology Inc.
Publication Date :
Revision: 1.0
Jul. 2012
57/57