IS31SE5000-UTLS2-EB

IS31SE5000 IR SENSOR FOR TOUCHLESS MOTION AND PROXIMITY
DESCRIPTION
PROCEDURE
The IS31SE5000 is a low-power, reflectance-based
infrared light sensor with advanced signal processing
and a digital output. The sensor can detect the
movement of nearby objects, making touchless motion
possible.
The IS31SE5000 evaluation board is fully assembled
and tested. Follow the steps listed below to verify
board operation.
The IS31SE5000 uses one infrared LED to transmit
and 2-channel receivers which pick up the reflectance
signal from the 2 photodiodes to perform touchless
motion detection. When a horizontal motion or an
object approaches, the flag bits in the IS31SE5000
status register will be triggered and an interrupt signal
is generated to inform the master to read the flag bit
through I2C interface.
1)
Connect the ground terminal of the power supply
to the GND and the positive terminal to the VCC.
Or connect the DC power to the connector (DC
IN).
2)
Turn on the power supply and pay attention to the
supply current. If the current exceeds 800mA,
please check for circuit fault.
FEATURES
EVALUATION BOARD OPERATION









Supply voltage from 2.7V~5.5V
400kHz I2C compatible interface
1µA shutdown current
0.6mA low supply current
Detection range can be adjusted
Motion Mode and Proximity Mode
Integrated signal processing and digital output
Auto interrupt clear
Package in UTQFN-12 (2mm × 2mm)
QUICK START
Figure 1: Photo of IS31SE5000 Evaluation Board
Caution: Do not turn on the power supply until all connections
are completed.
The evaluation board is controlled by an LPC922.
IS31SE5000 evaluation board supports both Motion
and Proximity Modes. Pressing a button switch will
select between 4 operating modes.
1)
Mode 1(Default): Motion Mode (The emitting
current is 400mA and detect distance is 9cm). The
Right LED will light when an object moves from
left to right directly above the IRLED and Photo
diode. The Left LED will light when an object
moves from right to left directly above the IRLED
and Photo diode.
2)
Mode 2:Motion Mode (The emitting current is
210mA and detect distance is 7.5cm). The Right
LED will light when an object moves from left to
right directly above the IRLED and Photo diode.
The Left LED will light when an object moves from
right to left directly above the IRLED and Photo
diode.
3)
Mode 3:Proximity Mode (The emitting current is
400mA and detect distance is 15cm). Both the
Left and Right LEDs will light when an object is
close to the IRLED and Photo diode.
4)
Mode 4:Proximity Mode (The emitting current is
210mA and detect distance is 12cm). Both the
Left and Right LEDs will light when an object is
close to the IRLED and Photo diode.
SOFTWARE SUPPORT
RECOMMENDED EQUIPMENT
Please refer to the integrated program.

The jumper JP1 is closed by default. If you want to
use an external MCU to control IS31SE5000, JP1
should be opened, the on board MCU will stop
working and its I2C ports will be high impedance.
Connect the external MCU to the I2C connector TP3
to control the IC.
5.0V, 2A power supply
ABSOLUTE MAXIMUM RATINGS

≤ 5.5V power supply
Caution: Do not exceed the conditions listed above, otherwise
the board will be damaged.
Integrated Silicon Solution, Inc. – www.issi.com
Rev. A, 01/06/2015
Please refer to the datasheet to get more information about
IS31SE5000.
1
IS31SE5000 IR SENSOR FOR TOUCHLESS MOTION AND PROXIMITY
ORDERING INFORMATION
Part No.
Temperature Range
Package
IS31SE5000-UTLS2-EB
-40°C ~ +85°C (Industrial)
UTQFN-12, Lead-free
Table 1: Ordering Information
For pricing, delivery, and ordering information, please contacts ISSI’s analog marketing team at
[email protected] or (408) 969-6600.
3V
BP
0R
R8
10
LDO
C6
C7
NC
1uF
VCC
C2
1uF
SDA
1
JP1
2
3
RST
4
5
3V
K1
R5
100K
6
7
INT
8
9
MODE
VCC
10
P0.0
P0.1
P1.7
P0.2
P1.6
P0.3
RST
P0.4
GND
P0.5
OSC1
OSC2
VDD
P0.6
INT1/P1.4
T1/P0.7
INT0/P1.3
T0/P1.2
TXD/P1.0
RXD/P1.1
20
SDA
19
SCL
18
SDB
17
P0.4
16
P0.5
R4 R1 R3 R2
100K 4.7K 4.7K 4.7K
4
SCL
3
INT
2
SDB
1
1uF
3V
13
12
11
8
RX1
D4
SDA
SCL
7
RX2
D5
INTB
SDB
12
GND
TP3
3V
C5
Optional (Note 1)
D3
IS31SE5000
15
14
11
IRLED
3V
U2
OPEN=EXT CTRL
D2
U1
0R
EN
GND
Vdd Vout
2
1
R9
VCC
C3
10nF
4
U3
5
1uF
3
C4
Right
R7
1k
R6
1k
3V
P0.5
P0.4
RST
GND
5
4
3
2
1
CON1
TP4
VCC
TP1
C1
DC IN
ICP
NC
GND
INT
SDA
SCL
SDB
1
2
3
4
5
TP2
LPC922
Left
Figure 2: IS31SE5000 Application Schematic
Integrated Silicon Solution, Inc. – www.issi.com
Rev. A, 01/06/2015
2
IS31SE5000 IR SENSOR FOR TOUCHLESS MOTION AND PROXIMITY
BILL OF MATERIALS
Name
Symbol
Description
Qty
Supplier
Part No.
Sensor IC
U1
IR sensor for touch less motion
and proximity
1
ISSI
IS31SE5000
MCU
U2
Microcontroller
1
NXP
LPC922
LDO
U3
Low-dropout regulator
1
PAM
PAM3101
LED Blue
Left, Right
Diode, LED Blue, SMD
2
Everlight
19-217/BHC-ZL1M2RY/3T
Resistor
R1~R3
RES,4.7k,1/16W,±5%,SMD
3
Yageo
RC0603JR-074K7L
Resistor
R4, R5
RES,100k,1/16W,±5%,SMD
2
Yageo
RC0603JR-07100KL
Resistor
R6, R7
RES,1k,1/16W,±5%,SMD
2
Yageo
RC0603JR-071KL
Resistor
R8
RES,0Ω,1/10W,±5%,SMD
1
Yageo
RL0805JR-070RL
Resistor
R9
RES,0Ω,1/16W,±5%,SMD
1
Yageo
RL0603JR-070RL
Capacitor
C1, C6
Not connect
2
Capacitor
C2,C4
CAP,1µF,25V,±10%,SMD
2
Yageo
CC0805KKX7R8BB105
Capacitor
C5,C7
CAP,1µF,50V,±10%,SMD
2
Yageo
CC0603KKX7R9BB105
Capacitor
C3
CAP,10nF,50V,±10%,SMD
1
Yageo
CC0603KKX7R9BB103
IRLED
D2
IRLED
1
Everlight
IR11-21C/TR8
PD
D4,D5
Photodiodes
2
Everlight
PD15-22C-R/TR8
PD
D3
Not connect (Note 1)
Note 1: There is only one photodiode can be put in D4 or D3 locations. Two locations make more choice for customers to select
distance between photodiode and IRLED.
Bill of Materials, refer to Figure 2 above.
Integrated Silicon Solution, Inc. – www.issi.com
Rev. A, 01/06/2015
3
IS31SE5000 IR SENSOR FOR TOUCHLESS MOTION AND PROXIMITY
0
0
3
1
2
5
4
3
2
1
2
2
2
0
2
2
1
1
0
Figure 3: Board Component Placement Guide - Top Layer
Figure 4: Board PCB Layout - Top Layer
Integrated Silicon Solution, Inc. – www.issi.com
Rev. A, 01/06/2015
4
IS31SE5000 IR SENSOR FOR TOUCHLESS MOTION AND PROXIMITY
Figure 5: Board Component Placement Guide - Bottom Layer
Figure 6: Board PCB Layout - Bottom Layer
Copyright © 2015 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its
products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services
described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information
and before placing orders for products.
Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction
of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness.
Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction,
that:
a.) the risk of injury or damage has been minimized;
b.) the user assume all such risks; and
c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances
Integrated Silicon Solution, Inc. – www.issi.com
Rev. A, 01/06/2015
5