TESTING
2 A CAPACITY RELAY
WITH HIGH SURGE
VOLTAGE & HIGH
BREAKDOWN VOLTAGE
15
.591
7.4
.291
8.2
.323
15
.591
7.4
.291
8.4
.331
mm inch
TX RELAYS
FEATURES
• Breakdown voltage between contacts and coil: 2,000 V
• Surge withstand between contacts and coil: 2,500 V
• High contact capacity: 2 A 30 V DC
• Surface-mount type available
SPECIFICATIONS
Contact
Characteristics
Arrangement
Initial contact resistance, max.
(By voltage drop 6 V DC 1 A)
Contact material
Nominal switching capacity
(resistive load)
Max. switching power
(resistive load)
Rating
Max. switching voltage
Max. switching current
Min. switching capacity ❇1
Nominal
operating
power
Single side stable
Expected
life (min.
operations)
2 A 30 V DC
resistive
Electrical
(at 20 cpm) 1 A 30 V DC
resistive
1 coil latching
2 coil latching
Mechanical (at 180 cpm)
2 Form C
100 mΩ
Gold-clad silver alloy
2 A 30 V DC
60 W
220 V DC
2A
10 µA 10 mV DC
140 mW (1.5 to 24 V DC)
270 mW (48 V DC)
100 mW (1.5 to 24 V DC)
200 mW (1.5 to 24 V DC)
108
105
5×105
Notes:
❇1This value can change due to the switching frequency, environmental conditions,
and desired reliability level, therefore it is recommended to check this with the actual load. (SX relays are available for low level load switching [10 µA 1 mV DC –
10 mA 10 V DC])
❇2The upper limit for the ambient temperature is the maximum temperature that
can satisfy the coil temperature rise. Under the packing condition, allowable temperature range is from –40 to +70°C –40°C to +158°F.
Remarks
* Specifications will vary with foreign standards certification ratings.
*1 Measurement at same location as "Initial breakdown voltage" section.
*2 By resistive method, nominal voltage applied to the coil; contact carrying current:
2 A.
*3 Nominal voltage applied to the coil, excluding contact bounce time.
4
* Nominal voltage applied to the coil, excluding contact bounce time without diode.
*5 Half-wave pulse of sine wave: 6 ms; detection time: 10 µs.
*6 Half-wave pulse of sine wave: 6 ms.
*7 Detection time: 10 µs.
*8 Refer to 6. Conditions for operation, transport and storage mentioned in
AMBIENT ENVIRONMENT.
Initial insulation resistance*1
Between open contacts
Initial
breakdown Between contact sets
voltage
Between contact and
coil
Between open
contacts
Initial surge (10×160 µs)
voltage
Between contacts
and coil (2×10 µs)
Temperature rise*2 (at 20°C)
Min. 1,000 MΩ (at 500 V DC)
1,000 Vrms for 1 min.
(Detection current: 10 mA)
1,000 Vrms for 1 min.
(Detection current: 10 mA)
2,000 Vrms for 1 min.
(Detection current: 10 mA)
1,500 V (FCC Part 68)
2,500 V (Telcordia)
Max. 50°C
Max. 4 ms (Approx. 2 ms)
Operate time [Set time]*3 (at 20°C)
[Max. 4 ms (Approx. 2 ms)]
Max. 4 ms (Approx. 1 ms)
Release time [Reset time]*4 (at
20°C)
[Max. 4 ms (Approx. 2 ms)]
Min. 750 m/s2 {75 G}
Functional*5
Shock resistance
Destructive*6
Min. 1,000 m/s2 {100 G}
196 m/s2 {20 G}, 10 to 55 Hz
Functional*7
at double amplitude of 3.3 mm
Vibration resistance
294 m/s2 {30G}, 10 to 55 Hz
Destructive
at double amplitude of 5 mm
–40°C to +85°C (up to 24 V coil)
Conditions for operation, transport and Ambient tem- –40°F to +185°F (up to 24 V coil)
perature ❇2
–40°C to +70°C (48 V coil)
storage*8
(Not freezing and
–40°F to +158°F (48 V coil)
condensing at low
Humidity
5 to 85% R.H.
temperature)
Unit weight
Approx. 2 g .071 oz
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
TX
ORDERING INFORMATION
Ex. TX
Contact arrangement
2
SA
Surface-mount availability
–
L
–
H
–
Operating function Terminal shape
Nil: Standard PC board terminal type or
Nil: self-clinching terminal type
SA: Standard surface-mount terminal type
SL : High connection reliability surface-mount
SL : terminal type
SS: Space saving surface-mount terminal type
–
3V
Z
Coil voltage (DC)
Packing style
Nil: Standard PC 1.5, 3, 4.5, 5, 6, Nil: Tube packing
board terminal or 9, 12, 24, 48* V Z: Tape and reel
surface-mount
packing(picked
terminal
from the 8/9/10/12
H: Self-clinching
-pin side
terminal
Notes: 1. Tape and reel (picked from 1/3/4/5-pin side) is also available by request. Part number suffix “-X” is
*48 V coil type: Single side stable only
2: 2 Form C
Nil: Single side
Nil: stable
L: 1 coil latching
L2: 2 coil latching
needed when ordering.
(ex.) TX2SA-3 V-X
2. Tape and reel packing symbol “-Z” or “-X” are not marked on the relay.
TYPES AND COIL DATA (at 20°C 68°F)
1) Standard PC board terminal type and self-clinching terminal type
1. Single side stable
Part No.
Standard PC
board terminal
TX2-1.5 V
TX2-3 V
TX2-4.5 V
TX2-5 V
TX2-6 V
TX2-9 V
TX2-12 V
TX2-24 V
TX2-48 V
Nominal
voltage,
V DC
Pick-up
voltage,
V DC (max.)
Drop-out
voltage,
V DC (min.)
1.5
3
4.5
5
6
9
12
24
48
1.13
2.25
3.38
3.75
4.5
6.75
9
18
36
0.15
0.3
0.45
0.5
0.6
0.9
1.2
2.4
4.8
Nominal
voltage,
V DC
Set voltage,
V DC (max.)
Reset voltage,
V DC (max.)
1.5
3
4.5
5
6
9
12
24
1.13
2.25
3.38
3.75
4.5
6.75
9
18
1.13
2.25
3.38
3.75
4.5
6.75
9
18
Self-clinching
terminal
Nominal
voltage,
V DC
Set voltage,
V DC (max.)
Reset voltage,
V DC (max.)
TX2-L2-H-1.5 V
TX2-L2-H-3 V
TX2-L2-H-4.5 V
TX2-L2-H-5 V
TX2-L2-H-6 V
TX2-L2-H-9 V
TX2-L2-H-12 V
TX2-L2-H-24 V
1.5
3
4.5
5
6
9
12
24
1.13
2.25
3.38
3.75
4.5
6.75
9
18
1.13
2.25
3.38
3.75
4.5
6.75
9
18
Self-clinching
terminal
TX2-H-1.5 V
TX2-H-3 V
TX2-H-4.5 V
TX2-H-5 V
TX2-H-6 V
TX2-H-9 V
TX2-H-12 V
TX2-H-24 V
TX2-H-48 V
Nominal
operating
current,
mA (±10%)
93.8
46.7
31
28.1
23.3
15.5
11.7
5.8
5.6
Coil
resistance,
Ω (±10%)
16
64.3
145
178
257
579
1,028
4,114
8,533
Nominal
operating
power,
mW
140
140
140
140
140
140
140
140
270
Max.
allowable
voltage,
V DC
2.2
4.5
6.7
7.5
9
13.5
18
36
57.6
Nominal
operating
power,
mW
100
100
100
100
100
100
100
100
Max.
allowable
voltage,
V DC
2.2
4.5
6.7
7.5
9
13.5
18
36
Nominal
operating
power,
mW
200
200
200
200
200
200
200
200
Max.
allowable
voltage,
V DC
2.2
4.5
6.7
7.5
9
13.5
18
36
2. 1 Coil latching
Part No.
Standard PC
board terminal
TX2-L-1.5 V
TX2-L-3 V
TX2-L-4.5 V
TX2-L-5 V
TX2-L-6 V
TX2-L-9 V
TX2-L-12 V
TX2-L-24 V
Self-clinching
terminal
TX2-L-H-1.5 V
TX2-L-H-3 V
TX2-L-H-4.5 V
TX2-L-H-5 V
TX2-L-H-6 V
TX2-L-H-9 V
TX2-L-H-12 V
TX2-L-H-24 V
Nominal
operating
current,
mA (±10%)
66.7
33.3
22.2
20
16.7
11.1
8.3
4.2
Coil
resistance,
Ω (±10%)
22.5
90
202.5
250
360
810
1,440
5,760
3. 2 Coil latching
Part No.
Standard PC
board terminal
TX2-L2-1.5 V
TX2-L2-3 V
TX2-L2-4.5 V
TX2-L2-5 V
TX2-L2-6 V
TX2-L2-9 V
TX2-L2-12 V
TX2-L2-24 V
Notes:
1. Specified value of pick-up, drop-out, set and reset voltage is with the condition of
square wave coil pulse.
Nominal
operating
current,
mA (±10%)
133.9
66.7
44.5
40
33.3
22.2
16.7
8.3
Coil
resistance,
Ω (±10%)
11.2
45
101.2
125
180
405
720
2,880
2. Standard packing: Tube: 40 pcs.; Case: 1,000 pcs.
3. In case of 5 V transistor drive circuit, it is recommended to use 4.5 V type relay.
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
TX
2) Surface-mount terminal type
1. Single side stable
Part No.
TX2S❍-1.5 V
TX2S❍-3 V
TX2S❍-4.5 V
TX2S❍-5 V
TX2S❍-6 V
TX2S❍-9 V
TX2S❍-12 V
TX2S❍-24 V
TX2S❍-48 V
Nominal
voltage,
V DC
Pick-up voltage,
V DC (max.)
Drop-out
voltage,
V DC (min.)
1.5
3
4.5
5
6
9
12
24
48
1.13
2.25
3.38
3.75
4.5
6.75
9
18
36
0.15
0.3
0.45
0.5
0.6
0.9
1.2
2.4
4.8
Nominal
voltage,
V DC
Set voltage,
V DC (max.)
Reset voltage,
V DC (max.)
1.5
3
4.5
5
6
9
12
24
1.13
2.25
3.38
3.75
4.5
6.75
9
18
Nominal
voltage,
V DC
1.5
3
4.5
5
6
9
12
24
Nominal
operating
current,
mA (±10%)
93.8
46.7
31
28.1
23.3
15.5
11.7
5.8
5.6
Coil resistance,
Ω (±10%)
Nominal
operating power,
mW
Max. allowable
voltage,
V DC
16
64.3
145
178
257
579
1,028
4,114
8,533
140
140
140
140
140
140
140
140
270
2.2
4.5
6.7
7.5
9
13.5
18
36
57.6
Nominal
operating
current,
mA (±10%)
Coil resistance,
Ω (±10%)
Nominal
operating power,
mW
Max. allowable
voltage,
V DC
1.13
2.25
3.38
3.75
4.5
6.75
9
18
66.7
33.3
22.2
20
16.7
11.1
8.3
4.2
22.5
90
202.5
250
360
810
1,440
5,760
100
100
100
100
100
100
100
100
2.2
4.5
6.7
7.5
9
13.5
18
36
Set voltage,
V DC (max.)
Reset voltage,
V DC (max.)
Nominal
operating
current,
mA (±10%)
Coil resistance,
Ω (±10%)
Nominal
operating power,
mW
Max. allowable
voltage,
V DC
1.13
2.25
3.38
3.75
4.5
6.75
9
18
1.13
2.25
3.38
3.75
4.5
6.75
9
18
133.9
66.7
44.5
40
33.3
22.2
16.7
8.3
11.2
45
101.2
125
180
405
720
2,880
200
200
200
200
200
200
200
200
2.2
4.5
6.7
7.5
9
13.5
18
36
2. 1 coil latching
Part No.
TX2S❍-L-1.5 V
TX2S❍-L-3 V
TX2S❍-L-4.5 V
TX2S❍-L-5 V
TX2S❍-L-6 V
TX2S❍-L-9 V
TX2S❍-L-12 V
TX2S❍-L-24 V
3. 2 coil latching
Part No.
TX2S❍-L2-1.5 V
TX2S❍-L2-3 V
TX2S❍-L2-4.5 V
TX2S❍-L2-5 V
TX2S❍-L2-6 V
TX2S❍-L2-9 V
TX2S❍-L2-12 V
TX2S❍-L2-24 V
❍: For each surface-mounted terminal variation, input the following letter.
SA type: A , SL type: L , SS type: S
Notes:
1. Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
2. Standard packing: Tube: 40 pcs.; Case: 1,000 pcs.
3. Tape and reel packing is also available for surface-mount type by request. Part number suffix "-X" or "-Z" is needed when ordering.
In this case, "X" or "Z" are not marked on the relay.
Quantity in tape and reel: 500 pcs.
• TX2SA-L-3V-Z
(ex.) • TX2SA-3V-X
Picked from the 1/3/4/5-pin side
Picked from the 8/9/10/12-pin side
4. In case of 5 V transistor drive circuit, it is recommended to use 4.5 V type relay.
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
TX
DIMENSIONS
mm inch
1. Single side stable and 1 coil latching type
15
Standard PC board terminal
.591
PC board pattern
(Copper-side view)
7.4
.291
0.65 8.2
.026 .323
0.5
.020
1.15
.045
Self clinching terminal
2.54
.100
3.5
.138
5.08
.200
5.08
.200
2.54
.100
Schematic (Bottom view)
Single side stable
1 coil latching
(Deenergized condition)
(Reset condition)
10.16
.400
+
0.25
.010
5.08
.200
–
8-1.0 dia
8-.039 dia
15
.591
7.4
.291
1
3 4 5
12
10 9 8
–
+
Direction indication*
Tolerance: ±0.1 ±.004
1
3 4 5
12
10 9 8
Direction indication*
*Orientation stripe located on top of relay.
0.65 8.2
.026 .323
0.5
.020
1.15
.045
3.5
.138
5.08
.200
5.08
.200
2.54
.100
0.25
.010
General tolerance: ±0.3 ±.012
Surface-mount terminal
SA type
1 5.08
.039 .200
15
.591
7.4
.291
8.2
.323
0.5
.020
5.08
.200
0.65
2.54 .026
.100
0.5
.020
5.08
.200
SS type
5.08
.200
1 5.08
.039 .200
Max.
10.0
.390
5.08
.200
Self clinching terminal
3 4 5
12
10 9 8
1
3 4 5
–
+
Direction indication
Direction indication
2.54
.100
6.24
.246
0.25
.010
7.4±0.5
.291±.020
15
.591
Tolerance: ±0.1 ±.004
PC board pattern
(Copper side view)
7.4
.291
12.7
.500
2.54
.100
3.5
.138
5.08
.200
1
+
2.54
.100
2.16
.085
0.65 8.2
.026 .323
0.5
.020
1.15
.045
10 9 8
7.24
.285
7.4
.291
0.65
2.54 .026
.100
12
3.16
.124
General tolerance: ±0.3 ±.012
2. Coil latching type
Standard PC board terminal
For glue-pad
15
.591
5.08
0.25
.200
9.4±0.5 .010
.370±.020
8.2
.323
0.5
.020
0.3
.012
1 5.08
.039 .200
Max.
10.0
.390
15
.591
–
7.24
.285
7.4
.291
0.65
2.54 .026
.100
Schematic (Top view)
Single side stable
1 coil latching
(Deenergized condition)
(Reset condition)
1.6
.0.63
3.16
.124
5.08
.200
0.25
9.4±0.5 .010
.370±.020
8.2
.323
2.54
.100
8.4
.331
15
.591
SL type
Suggested mounting pad
(Top view)
5.08
.200
2.54
.100
15
.591
5.08
.200
0.25
.010
10-1.0 dia
10-.039 dia
7.4
.291
Schematic (Bottom view)
2 coil latching (Reset condition)
1
3 4 5 6
+
–
+
–
12
10 9 8 7
Direction indication*
Tolerance: ±0.1 ±.004
0.65 8.2
.026 .323
0.5
.020
1.15
.045
3.5
.138
5.08
.200
5.08
.200
2.54
.100
0.25
.010
General tolerance: ±0.3 ±.012
Surface-mount terminal
SA type
Suggested mounting pad (Top view)
15
.591
8.2
.323
0.5
.020
5.08
.200
5.08
.200
0.25
9.4±0.5 .010
.370±.020
0.65
2.54 .026
.100
0.5
.020
5.08
.200
SS type
0.65
2.54 .026
.100
For glue-pad
2.54
.100
3.16
.124
7.24
.285
7.4
.291
8.2
.323
5.08
.200
15
.591
5.08
0.25
.200
9.4±0.5 .010
.370±.020
0.65
2.54 .026
.100
1 5.08
.039 .200
Max.
10.0
.390
2.54
.100
2.16
.085
5.08
.200
6.24
.285
0.25
.010
7.4±0.5
.291±.020
General tolerance: ±0.3 ±.012
Schematic (Top view)
2 coil latching (Reset condition)
12
Tolerance: ±0.1 ±.004
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
10 9 8
+
+
1
0.3
.012
1 5.08
.039 .200
Max.
10.0
.390
15
.591
0.5
.020
1.6
.0.63
7.24
.285
7.4
.291
8.2
.323
2.54
.100
3.16
.124
8.4
.331
15
.591
SL type
1 5.08
.039 .200
7.4
.291
7
–
–
3
4 5
Direction indication
6
TX
REFERENCE DATA
1. Maximum switching capacity
2. Life curve
3. Mechanical life
Ratio against the rated voltage, %V
Tested sample: TX2-5V, 10 pcs.
Operating frequency: 180 cpm
3.0
100
No. of operations ×104
Switching current, A
2.0
DC resistive load
1.0
0.5
0.4
0.3
50
30V DC
resistive load
30
20
10
0.2
100
90
80
Pick-up voltage
70
Max.
60
Min.
50
40
30
Drop-out voltage
20
Max.
Min.
10
0
20 30
0
50
100
200 300
Contact voltage, V
0
1.0
2.0
Switching current, A
10
100
1,000
No. of operations, ×104
10,000
4. Electrical life
5-(1). Coil temperature rise
Tested sample: TX2-5V, 6 pcs.
Operating frequency: 20 cpm
Tested sample: TX2-5V, 6 pcs.
Point measured: Inside the coil
Ambient temperature: 25°C 77°F, 85°C 185°F
Change of contact resistance
100
90
90
80
Pick-up voltage
70
Max.
60
Min.
50
40
Drop-out voltage
Max.
30
20
70
80
70
60
50
40
Max.
30
Min.
+25°C +77°F
+85°C +185°F
60
50
40
30
2A
2A
20
0A
0A
20
Min.
0
1
2
3
4 5 6 7 8 9
No. of operations, ×104
10
10
0
10
1
2
3
4 5 6 7 8 9
4
No. of operations, ×10
5-(2). Coil temperature rise
6-(1). Operate and release time (with diode)
Tested sample: TX2-48V, 6 pcs.
Point measured: Inside the coil
Ambient temperature: 25°C 77°F, 70°C 158°F
Tested sample: TX2-5V, 10 pcs.
+25°C +77°F
+70°C +158°F
60
50
2A
40
2A
0A
30
0A
20
0
4
Max.
3
Min.
2
Max.
Min.
0
100 110 120 130 140 150
No. of operations, ×104
120 130 140 150
No. of operate, ×104
5
Operate time
Release time
1
10
100 110
6-(2). Operate and release time (without diode)
5
Operate and release time, ms
70
0
10
Operate and release time, ms
10
Temperature rise, °C
Temperature rise, °C
100
Contact resistance, mΩ
Ratio against the rated voltage, %V
Change of pick-up and drop-out voltage
Operate time
Release time
4
Max.
Min.
3
2
Max.
Min.
1
70
80
90
100 110 120
Coil applied voltage, %V
0
70
80
90
100 110 120
Coil applied voltage, %V
8. Distribution of set and reset voltage
9. Ambient temperature characteristics
Tested sample: TX2-5V, 50 pcs.
Tested sample: TX2-L2-12V, 30 pcs.
Tested sample: TX2-5V, 5 pcs.
10
0
0
10 20 30 40 50 60 70 80 90 100
Ratio against the rated voltage, %V
Rate of change, %
Quantity
Drop-out voltage
20
Set voltage
Reset voltage
15
Pick-up voltage
;;;;;;;
;;;;;;
Quantity
30
;
;
;
;
;;;;;;;;;;
;;;;;
7. Distribution of pick-up and drop-out voltage
10
–40 –20
5
0
40
20
Pick-up voltage
20 40 60 80
Ambient temperature, °C
–20
–40
0
0
10 20 30 40 50 60 70 80 90 100
Ratio against the rated voltage, %V
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
Drop-out
voltage x
x
TX
10. Distribution of contact resistance
11-(1). High frequency characteristics
11-(2). High frequency characteristics
Tested sample: TX2-5V, 30 pcs. (30 × 4 contacts)
Tested sample: TX2-12V, 2 pcs.
Isolation characteristics
Tested sample: TX2-12V, 2 pcs.
Insertion loss characteristics
1
3 4 5
12
10 9 8
20
15
10
5
0 20
Terminal
Nos. 3-4, 9-10
100
50
0.4
0.2
10
30
40
50
Contact resistance, mΩ
100
Frequency, MHz
1,000
12-(2). Malfunctional shock (latching)
Tested sample: TX2-5V, 6 pcs
Tested sample: TX2-L2-12V, 6 pcs.
Z XX'
Y
1000m/s 2
Deenergized condition
Energized condition
Z'
Y
Y'
Z XX'
X
1000m/s2
Z
1000m/s2
1000m/s 2
Z'
1000m/s2
X'
1000m/s 2
Z'
1000m/s2
X'
0
–5
ON
OFF OFF
Drop-out voltage
–5
OFF
2
4 6
8 10
.079 .157 .236 .315 .394
Inter-relay distance
1,000
13-(3). Influence of adjacent mounting
Rate of change, %
Rate of change, %
ON
Rate of change, %
Rate of change, %
Rate of change, %
ON
13-(2). Influence of adjacent mounting
Pick-up voltage
0
100
Frequency, MHz
1000m/s 2
Y'
13-(1). Influence of adjacent mounting
5
10
Reset state
Set state
Z
1000m/s2
1000m/s 2
Y'
0
Y
1000m/s 2
X
1000m/s2
5
0.8
0.6
12-(1). Malfunctional shock (single side stable)
Z'
Y
Y'
1.0
ON
5
Pick-up voltage
0
ON
–5
ON
Rate of change, %
0
Insertion loss, dB
25
(BOTTOM VIEW)
Isolation, dB
Quantity
30
;;;;;;;
;
;;;;;;;;;
;;;;;;;;;;
;
;;;;;;;;
35 Terminal
Nos. 4-5, 8-9
OFF
5
Drop-out voltage
0
OFF
–5
OFF
0
, mm inch
2
4 6
8 10
.079 .157 .236 .315 .394
Inter-relay distance
5
Pick-up voltage
ON
0
ON
–5
ON
ON
5
0
OFF
Drop-out voltage
OFF
–5
OFF
OFF
0
, mm inch
2
4 6
8 10
.079 .157 .236 .315 .394
Inter-relay distance
, mm inch
14. Pulse dialing test
Circuit
+
458 Ω
0.08
µF
48V DC
–
0.08
µF
458 Ω
Wire spring relay
4
3
Ratio against the rated voltage, %V
Change of pick-up and drop-out voltage
Change of contact resistance
100
100
90
90
80
Pick-up voltage
70
Max.
Min.
60
50
40
Drop-out voltage
30
20
Contact resistance, mΩ
Tested sample: TX2-5V, 6 pcs.
(35 mA 48 V DC wire spring relay load)
Max.
Min.
70
60
50
Max.
40
Min.
30
20
10
10
0
80
10
20
30
40
4
No. of operation, ×10
50
Note: Data of surface-mount type are the same as those of PC board terminal type.
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
0
10
20
30
40
No. of operations, ×104
50
TX
Notes
1. Packing style
1) The relay is packed in a tube with the
relay orientation mark on the left side, as
shown in the figure below.
2) Tape and reel packing (surface-mount
terminal type)
(1) Tape dimensions
(i) SA type
(2) Dimensions of plastic reel
mm inch
21 ±0.6 dia.
.827 ±.024 dia.
mm inch
2.0 ±0.5
.079 ±.020
Orientation (indicates PIN No.1)stripe
+0.1
0 dia.
Relay polarity bar 1.5 +.004
.059 0 dia. 2.0
(Z type)
.079
1.75
.069
4.0
.157
0.4
.016
100 ±1 dia.
3.937 ±.039 dia.
C
A
Stopper (gray)
Stopper (green)
B
11.5
.453
D
16.0 10.0 .394
.630
TX/TX-D/TX-S
-SMD relays
15.5
.610
24.0 ±0.3
±0.2
.945 ±.012 9.2±.008
.362
Tape coming out direction
(ii) SL type
mm inch
+0.1
0 dia.
Relay polarity bar 1.5 +.004
.059 0 dia. 2.0
(Z type)
.079
1.75
.069
4.0
.157
0.4
.016
11.5
.453
15.5
.610
TX/TX-D/TX-S
-SMD relays
16.0
.630
10.0
.394
Tape coming out direction
24.0 ±0.3
.945 ±.012
10.8±0.2
.425±.008
(iii) SS type
mm inch
+0.1
0 dia.
Relay polarity bar 1.5 +.004
.059 0 dia. 2.0
(Z type)
.079
2.2 dia.
.087 dia.
4.0
1.75
.157
.069
0.4
.016
11.5
.453
15.5
.610
TX/TX-D/TX-S
-SMD relays
16.0
.630
Tape coming out direction
8.0 24.0 ±0.3
±.012
.315 .945 10.8±0.2
.425±.008
For Cautions for Use, see Relay Technical Information.
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
370 ±2 dia.
14.567 ±.079 dia.
±0.5
13 dia.
.512 ±.020 dia.
24.4+20
.961+.079
0
2.0±0.2
.079±.008