AM2520CGCK09

SUBMINIATURE SOLID STATE LAMP
Part Number: AM2520CGCK09
Green
Features
Description
z Subminiature package.
The Green source color devices are made with AlGaInP on
z Z-bend lead.
GaAs substrate Light Emitting Diode.
z Long life - solid state reliability.
z Low package profile.
z Moisture sensitivity level : level 3.
z Package : 1000pcs / reel.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
5. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAC3400
REV NO: V.10B
DATE: AUG/26/2013
PAGE: 1 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: D.N.Huang
ERP: 1202000450
Selection Guide
Part No.
Dice
AM2520CGCK09
Iv (mcd) [2]
@ 20mA
Lens Type
Green (AlGaInP)
Viewing
Angle [1]
Min.
Typ.
2θ1/2
400
800
20°
Water Clear
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Green
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
574
nm
IF=20mA
Green
570
nm
IF=20mA
Spectral Line Half-width
Green
20
nm
IF=20mA
C
Capacitance
Green
15
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Green
2.1
2.5
V
IF=20mA
IR
Reverse Current
Green
10
uA
VR=5V
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
Absolute Maximum Ratings at TA=25°C
Parameter
Green
Units
Power dissipation
75
mW
DC Forward Current
30
mA
Peak Forward Current [1]
150
mA
5
V
Reverse Voltage
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAC3400
REV NO: V.10B
DATE: AUG/26/2013
PAGE: 2 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: D.N.Huang
ERP: 1202000450
Green
AM2520CGCK09
SPEC NO: DSAC3400
REV NO: V.10B
DATE: AUG/26/2013
PAGE: 3 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: D.N.Huang
ERP: 1202000450
AM2520CGCK09
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAC3400
REV NO: V.10B
DATE: AUG/26/2013
PAGE: 4 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: D.N.Huang
ERP: 1202000450
PACKING & LABEL SPECIFICATIONS
AM2520CGCK09
Terms and conditions for the usage of this document
1.The information included in this document reflects representative usage scenarios and is intended
for technical reference only.
2.The part number, type, and specifications mentioned in this document are subject to future change
and improvement without notice. Before production usage customer should refer to the latest
datasheet for the updated specifications.
3.When using the products referenced in this document, please make sure the product is being
operated within the environmental and electrical limits specified in the datasheet. If customer usage
exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.
4.The information in this document applies to typical usage in consumer electronics applications.
If customer's application has special reliability requirements or have life-threatening liabilities,
such as automotive or medical usage, please consult with Kingbright representative for further
assistance.
5.The contents and information of this document may not be reproduced or re-transmitted without
permission by Kingbright.
6.All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAC3400
REV NO: V.10B
DATE: AUG/26/2013
PAGE: 5 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: D.N.Huang
ERP: 1202000450