T-1 3/4 (5mm) SOLID STATE LAMP Part Number: WP7113SGD14V Super Bright Green ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z Low power consumption. z The Super Bright Green source color devices are made z Popular T-1 3/4 diameter package. with Gallium Phosphide Green Light Emitting Diode. z Electrostatic discharge and power surge could damage z General purpose leads. the LEDs. z Reliable and rugged. z Long life - solid state reliability. z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs. z Available on tape and reel. z All devices, equipments and machineries must be z 14V internal resistor. electrically grounded. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAF2428 REV NO: V.6B DATE: JAN/26/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101011662 Selection Guide Part No. Dice WP7113SGD14V Lens Type Super Bright Green (GaP) Viewing Angle [1] Iv (mcd) [2] V= 14V Min. Typ. 2θ1/2 10 22 30° Green Diffused Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Super Bright Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 565 nm VF=14V Super Bright Green 568 nm VF=14V Spectral Line Half-width Super Bright Green 30 nm VF=14V IF Forward Current Super Bright Green 10.5 13.5 mA VF=14V IR Reverse Current Super Bright Green 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Wavelength value is traceable to the CIE127-2007 compliant national standards. 3. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Super Bright Green Units Power dissipation 160 mW Forward Voltage 16 V Reverse Voltage 5 V Operating Temperature -40°C To +70°C Storage Temperature -40°C To +85°C Lead Solder Temperature [1] 260°C For 3 Seconds Lead Solder Temperature [2] 260°C For 5 Seconds Notes: 1. 2mm below package base. 2. 5mm below package base. SPEC NO: DSAF2428 REV NO: V.6B DATE: JAN/26/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101011662 Super Bright Green WP7113SGD14V SPEC NO: DSAF2428 REV NO: V.6B DATE: JAN/26/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101011662 PACKING & LABEL SPECIFICATIONS WP7113SGD14V Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF2428 REV NO: V.6B DATE: JAN/26/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101011662 SPEC NO: DSAF2428 REV NO: V.6B DATE: JAN/26/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101011662 SPEC NO: DSAF2428 REV NO: V.6B DATE: JAN/26/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101011662