2x5mm RECTANGULAR LED LAMP Part Number: WP113HDT Bright Red Features Description Low power consumption. The Bright Red source color devices are made with Gallium Reliable and rugged. Phosphide Red Light Emitting Diode. Excellent uniformity of light output. Suitable for level indicator. Long life - solid state reliability. RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAF2582 REV NO: V.5B DATE: JAN/05/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101000530 Selection Guide Part No. Dice WP113HDT Bright Red (GaP) Viewing Angle [1] Iv (mcd) [2] @ 10mA Lens Type Min. Typ. 2θ1/2 0.2 0.6 110° Red Diffused Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Bright Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 700 nm IF=20mA Bright Red 635 nm IF=20mA Spectral Line Half-width Bright Red 45 nm IF=20mA C Capacitance Bright Red 40 pF VF=0V;f=1MHz VF [2] Forward Voltage Bright Red 2.25 2.5 V IF=20mA IR Reverse Current Bright Red 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Bright Red Units 62.5 mW DC Forward Current 25 mA Peak Forward Current [1] 130 mA 5 V Power dissipation Reverse Voltage Operating/Storage Temperature -40°C To +85°C Lead Solder Temperature [2] 260°C For 3 Seconds Lead Solder Temperature [3] 260°C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. SPEC NO: DSAF2582 REV NO: V.5B DATE: JAN/05/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101000530 Bright Red WP113HDT SPEC NO: DSAF2582 REV NO: V.5B DATE: JAN/05/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101000530 PACKING & LABEL SPECIFICATIONS WP113HDT Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF2582 REV NO: V.5B DATE: JAN/05/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101000530 SPEC NO: DSAF2582 REV NO: V.5B DATE: JAN/05/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101000530 SPEC NO: DSAF2582 REV NO: V.5B DATE: JAN/05/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101000530