3.0mmx1.5mm SMD CHIP LED LAMP Part Number: APL3015SECK-F01 Super Bright Orange Features Description z 3.0mmx1.5mm SMT LED, 1.4mm thickness. The Super Bright Orange device is made with AlGaInP (on z Low power consumption. GaAs substrate) light emitting diode chip. z Ideal for backlight and indicator. z Various colors and lens types available. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAF1075 REV NO: V.6A DATE: NOV/01/2013 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203001611 Selection Guide Part No. Dice APL3015SECK-F01 Iv (mcd) [2] @ 20mA Lens Type Super Bright Orange (AlGaInP) Water Clear Viewing Angle [1] Min. Typ. 350 600 *120 *350 2θ1/2 70° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Super Bright Orange λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 610 nm IF=20mA Super Bright Orange 601 nm IF=20mA Spectral Line Half-width Super Bright Orange 29 nm IF=20mA C Capacitance Super Bright Orange 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Orange 2.1 2.5 V IF=20mA IR Reverse Current Super Bright Orange 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Parameter Super Bright Orange Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 195 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAF1075 REV NO: V.6A DATE: NOV/01/2013 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203001611 Super Bright Orange APL3015SECK-F01 SPEC NO: DSAF1075 REV NO: V.6A DATE: NOV/01/2013 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203001611 APL3015SECK-F01 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAF1075 REV NO: V.6A DATE: NOV/01/2013 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203001611 PACKING & LABEL SPECIFICATIONS APL3015SECK-F01 Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF1075 REV NO: V.6A DATE: NOV/01/2013 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203001611