3.2x1.6mm SMD CHIP LED LAMP Part Number: APTR3216ZGC/E Green ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 3.2mmx1.6mm SMT LED,1.05mm thickness. z The Green source color devices are made with InGaN Light Emitting Diode. z Low power consumption. z Electrostatic discharge and power surge could damage z Wide viewing angle. z Ideal for backlight and indicator. the LEDs. z It is recommended to use a wrist band or anti- z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be z RoHS compliant. electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAK0184 REV NO: V.4B DATE: APR/29/2015 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203010106 Selection Guide Part No. Dice APTR3216ZGC/E Green (InGaN) Water Clear Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 2θ1/2 400 650 120° Notes: 1. θ1 / 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value. 2. Luminous intensity / luminous Flux: + / -15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 520 nm IF=20mA Green 525 nm IF=20mA Spectral Line Half-width Green 35 nm IF=20mA C Capacitance Green 100 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 3.2 4 V IF=20mA IR Reverse Current Green 50 uA VR=5V Notes: 1. Wavelength: + / -1nm. 2. Forward Voltage: + / -0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Green Units Power dissipation 120 mW DC Forward Current 30 mA Peak Forward Current [1] 100 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1 / 10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAK0184 REV NO: V.4B DATE: APR/29/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203010106 Green APTR3216ZGC/E SPEC NO: DSAK0184 REV NO: V.4B DATE: APR/29/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203010106 APTR3216ZGC/E Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAK0184 REV NO: V.4B DATE: APR/29/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203010106 PACKING & LABEL SPECIFICATIONS APTR3216ZGC/E Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAK0184 REV NO: V.4B DATE: APR/29/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203010106