HT83F02 External Voice Memory Flash MCU

HT83F02
External Voice Memory Flash MCU
Features
· Operating voltage: 2.4V~5.5V
· Two 8-bit programmable timer counter with 8-stage
prescaler and one time base counter
· System clock: 4MHz~12MHz
· Three oscillators:
· 12-bit high quality voltage type D/A output
External Crystal - HXT
External RC - ERC
Internal RC - HIRC
· Fully integrated internal 4MHz, 8MHz and 12MHz
oscillator requires no external components
· Up to 19 I/O pins
· Two sets of Serial Interfaces Module - SIM for SPI
or I2C, shared with PB
· PWM circuit direct drive speaker
· Watchdog Timer function
· 8-level subroutine nesting
· 2.7V Low voltage detection, tolerance 5%
· 2.4V Low voltage reset, tolerance 5%
· Power-down function and wake-up feature reduce
power consumption
· 63 powerful instructions
· 2K´16 Flash Program Memory
· 28-pin SOP package
· 208´8 Data Memory
General Description
This device is excellent solutions for versatile voice and
sound effect product applications with their efficient
MCU instructions providing the user with programming
capability for powerful custom applications. The system
frequency can be up to 12MHz at an operating voltage
of 5V and include a power-down function to reduce
power consumption. A full choice of HXT, ERC and
HIRC oscillator functions are provided including a fully
integrated system oscillator which requires no external
components for its implementation.
The Flash type voice of MCU has Flash type Program
Memory and Connect External flash through SPI Serial
Interface. Offering users the convenience of Flash
Memory multi-programming features, this device also
includes a wide range of functions and features which
include a voice synthesizer and tone generator.
This device is designed for applications which require
multiple I/Os and sound effects, such as voice and melody. It can provide various sampling rates and beats,
tone levels, tempos for speech synthesizer and melody
generator. It also includes two integrated high quality,
voltage type DAC outputs and voltage type PWM outputs.
Rev. 1.40
The MCU flash voice memory capacity determine by
user, into which the user can download their voice data.
1
April 19, 2011
HT83F02
Block Diagram
The following block diagram illustrates the main functional blocks.
W a tc h d o g
T im e r
F la s h In - C ir c u it
P r o g r a m m in g ( IC P )
F la s h R O M
P ro g ra m
M e m o ry
R e s e t
C ir c u it
8 - b it
R IS C
M C U
C o re
S ta c k
L o w
V o lta g e
D e te c tio n
R A M D a ta
M e m o ry
W a tc h d o g
T im e r O s c illa to r
In te rru p t
C o n tr o lle r
H IR C
O s c illa to r
E R C /C ry s ta l
O s c illa to r
P W M
I/O
P o rts
8 - b it
T im e r
S P I
F u n c tio n
D /A
C o n v e rte rs
I2C
F u n c tio n
Pin Assignment
P A 1
1
2 8
P A 2
P B 0 /S D O B /S D A B
3
2 6
P A 4
2 7
2
P A 0
2 5
4
P B 1 /S C K B /S C L B
2 4
5
P B 2 /S D IB
2 3
6
P B 4 /S D O A /S D A A
2 2
7
P B 5 /S C K A /S C L A
P B 6 /S D IA
P B 7 /S C S A
P C 1 /O S C 1
P C 2 /O S C 2
V S S A
A U D
V D D A
2 1
8
2 0
9
1 9
1 0
1 8
1 1
1 7
1 2
1 6
1 3
1 5
1 4
P A 3
P A 5
P A 6
P A 7
V S S
V D D
V D D _ P B IO
P C 0 /R E S
V S S P
P W M 2
P W M 1
V D D P
H T 8 3 F 0 2
2 8 S O P -A
Rev. 1.40
2
April 19, 2011
HT83F02
Pin Description
Pin Name
I/O
Options
I/O
Bidirectional 8-bit I/O port, Each bit can be configured as a wake-up input by
Wake-up,
configuration option. Software instructions determine if the pin is a CMOS outPull-high
put or Schmitt trigger input. Configuration options determine which pins on
or None
this port have pull-high resistors.
PB0/SDOB/SDAB
PB1/SCKB/SCLB
PB2/SDIB
PB3/SCSB
PB4/SDOA/SDAA
PB5/SCKA/SCLA
PB6/SDIA
PB7/SCSA
I/O
Pull-high
or None
Bidirectional 8-bit I/O port. Software instructions determine if the pin is a
CMOS output or Schmitt trigger input. Configuration options determine which
pins on this port have pull-high resistors. Pins PB0~PB3 are pin-shared with
SIMB control pins SDOB/SDAB, SCKB/SCLB, SDIB and SCSB respectively.
Pins PB4~PB7 are pin-shared with SIMA control pins SDOA/SDAA,
SCKA/SCLA, SDIA and SCSA respectively.
VSS
¾
¾
Negative digital power supply, ground
VDD
¾
¾
Positive digital power supply
VDD_PBIO
¾
¾
PB I/O external positive power supply(determine by option)
I
¾
Schmitt trigger reset input or PC0 I/O pin. Configuration option determines if
the pin is as a reset pin or GPIO pin. Software instructions determine if this pin
has pull-high resistor.
OSC1, OSC2 are connected to an external RC network, external crystal or no
connection, determined by configuration option, for the internal system clock.
If the ERC system clock option is selected, pin OSC2 can be as PC2. If the
IRC system clock option is selected, the OSC1/OSC2 pins will be IO pins
PC1/PC2. Software instructions determine which pins on this port have
pull-high resistors.
PA0~PA7
PC0/RES
Description
PC1/OSC1
PC2/OSC2
¾
Crystal,
ERC or
IRC
VSSA
¾
¾
AUD
O
CMOS
VDDA
¾
¾
Positive DAC circuit power supply
VDDP
¾
¾
PWM positive power supply
PWM1, PWM2
O
¾
PWM circuit direct speaker drive
VSSP
¾
¾
PWM negative power supply, ground
Negative DAC circuit power supply, ground
Audio output for driving external transistor or power amplifier.
Note: Each pin on PA can be programmed through a configuration option to have a wake-up function.
Individual pins can be selected to have pull-high resistors.
Absolute Maximum Ratings
Supply Voltage ...........................VSS+2.4V to VSS+5.5V
Storage Temperature ..........................-50°C to +125°C
Input Voltage..............................VSS-0.3V to VDD+0.3V
IOL Total ..............................................................150mA
Total Power Dissipation .....................................500mW
Operating Temperature.........................-40°C to +85°C
IOH Total............................................................-100mA
Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed
in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
Rev. 1.40
3
April 19, 2011
HT83F02
D.C. Characteristics
Ta=25°C
Test Conditions
Symbol
Parameter
Min.
Typ.
Max.
Unit
fSYS=8MHz
2.4
¾
5.5
V
fSYS=10MHz
2.7
¾
5.5
V
fSYS=12MHz
3.3
¾
5.5
V
fSYS=6MHz
2.4
¾
5.5
V
fSYS=8MHz
2.7
¾
5.5
V
fSYS=12MHz
2.7
¾
5.5
V
fSYS=8MHz
2.4
¾
5.5
V
fSYS=12MHz
2.7
¾
5.5
V
¾
0.8
1.5
mA
¾
2.5
4.0
mA
¾
1.0
2.0
mA
¾
2.3
4.5
mA
¾
1.1
2.5
mA
¾
2.7
5.5
mA
¾
0.7
1.5
mA
¾
1.7
3.0
mA
¾
1.0
2.0
mA
¾
2.1
4.5
mA
¾
1.4
3.0
mA
¾
3.1
6.0
mA
¾
0.5
1.2
mA
¾
1.2
2.5
mA
¾
1.1
2.0
mA
¾
2.2
4.5
mA
¾
1.4
3.0
mA
¾
3.2
6.0
mA
No load, system HALT,
WDT enable, fSYS=12MHz
¾
1.1
5.0
mA
¾
4.1
10.0
mA
No load, system HALT,
WDT disable, fSYS=12MHz
¾
0.2
1.0
mA
¾
0.4
2.0
mA
7
13
¾
mA
15
30
¾
mA
-3.5
-5
¾
mA
-8.0
-12
¾
mA
70
100
¾
mA
125
180
¾
mA
VDD
VDD1
VDD2
VDD3
Operating Voltage
(Crystal OSC)
Operating Voltage
(External RC OSC)
Operating Voltage
(High Frequency Internal RC OSC)
¾
¾
¾
3V
5V
IDD1
Operating Current
(Crystal OSC, fSYS=fH)
3V
5V
3V
5V
3V
5V
IDD2
Operating Current
(ERC OSC, fSYS=fH)
3V
5V
3V
5V
3V
5V
IDD3
Operating Current
(HIRC OSC, fSYS=fH)
3V
5V
3V
5V
ISTB1
ISTB2
IOL1
Standby Current
(Crystal, ERC, HIRC OSC)
3V
Standby Current
(Crystal, ERC, HIRC OSC)
3V
5V
5V
3V
I/O Port Sink Current
Conditions
No load, fH=8MHz,
WDT enable
No load, fH=10MHz,
WDT enable
No load, fH=12MHz,
WDT enable
No load, fH=6MHz,
WDT enable
No load, fH=8MHz,
WDT enable
No load, fH=12MHz,
WDT enable
No load, fH=4MHz,
WDT enable
No load, fH=8MHz,
WDT enable
No load, fH=12MHz,
WDT enable
VOL=0.1VDD
5V
IOH1
3V
I/O Port Source Current
VOH=0.9VDD
5V
IOL2
3V
PWM1/PWM2 Sink Current
VOL=0.1VDD
5V
Rev. 1.40
4
April 19, 2011
HT83F02
Test Conditions
Symbol
Parameter
VDD
IOH2
3V
PWM1/PWM2 Sink Current
VOH=0.9VDD
5V
VIL1
VIH1
VIL2
VIH2
VIL3
VIH3
VIL4
VIH4
RPH
IAUD
Min.
Typ.
Max.
Unit
-38
-55
¾
mA
-80
-115
¾
mA
Conditions
3V
¾
¾
1.0
¾
V
5V
¾
¾
2.0
¾
V
3V
¾
¾
1.9
¾
V
5V
¾
¾
3.0
¾
V
3V
¾
¾
1.4
¾
V
5V
¾
¾
2.8
¾
V
3V
¾
¾
2.1
¾
V
5V
¾
¾
3.7
¾
V
Input Low Voltage for PB I/O Ports
(PBVDD=VDD)
3V
¾
¾
1.1
¾
V
5V
¾
¾
2.2
¾
V
Input High Voltage for PB I/O Ports
(PBVDD=VDD)
3V
¾
¾
1.9
¾
V
5V
¾
¾
3.0
¾
V
Input Low Voltage for PB I/O Ports
(PBVDD=VDD_PBIO)
3V
¾
¾
1.3
¾
V
5V
¾
¾
2.5
¾
V
Input Low Voltage for PB I/O Ports
(PBVDD=VDD_PBIO)
3V
¾
¾
1.6
¾
V
5V
¾
¾
2.6
¾
V
3V
¾
20
60
100
kW
5V
¾
10
30
50
kW
Input Low Voltage for PA I/O Ports
Input High Voltage for PA I/O Ports
Input Low Voltage (RES)
Input High Voltage (RES)
Pull-high Resistance
3V
VOH=0.9VDD
¾
-4.5
¾
mA
5V
VOH=0.9VDD
¾
-10.5
¾
mA
AUD Current Source
VLVR
Low Voltage Reset Voltage
¾
LVR 2.4V option
2.28
2.40
2.52
V
VLVD
Low Voltage Detection Voltage
¾
LVR 2.7V option
2.565
2.700
2.835
V
Rev. 1.40
5
April 19, 2011
HT83F02
A.C. Characteristics
Ta=25°C
Test Conditions
Symbol
Parameter
System Clock
(Crystal OSC)
fSYS1
fSYS2
System clock (External RC OSC)
fSYS3
System clock (HI RC OSC)
tRES
External Reset Low Pulse Width
tSST
System Start-up Timer Period
(wake-up from HALT)
Min.
Typ.
Max.
Unit
¾
2
¾
8
MHz
2.7V~
5.5V
¾
2
¾
10
MHz
3.3V~
5.5V
¾
2
¾
12
MHz
-2% ´
Typ.
8
2% ´
Typ.
MHz
-2% ´
Typ.
8
2% ´
Typ.
MHz
1
¾
¾
ms
fSYS=XTAL
¾
1024
¾
tSYS
fSYS=ERC or HIRC OSC
¾
15~16
¾
tSYS
¾
1
¾
¾
tSYS
VDD
Conditions
2.4V~
5.5V
5V
Ta=25°C,
External RERC=120kW
3V/5V Ta=25°C
¾
¾
¾
tINT
Interrupt Pulse Width
¾
¾
7
¾
8
ms
tLVR
Low Voltage Width to Reset
¾
¾
320
840
1200
ms
tLVD
LVD Time
¾
¾
15
¾
¾
ms
Note: tSYS=1/fSYS
tSUB=1/fSUB
Rev. 1.40
6
April 19, 2011
HT83F02
Power-on Reset Characteristics
Test Conditions
Symbol
Parameter
VDD
Conditions
Min.
Typ.
Max.
Unit
VPOR
VDD Start Voltage to Ensure
Power-on Reset
¾
¾
¾
¾
100
mV
RRVDD
VDD raising rate to Ensure
Power-on Reset
¾
¾
0.035
¾
¾
V/ms
tPOR
Minimum Time for VDD Stays at
VPOR to Ensure Power-on Reset
¾
¾
1
¾
¾
ms
V
D D
tP
O R
R R
V D D
V
P O R
T im e
Characteristics Curves
R vs. F (External RC) Chart Characteristics Curve at 25°C
R
1 4
v s . F C h a rt
F re q u e n c y (M H z )
1 2
1 0
V
8
D D
= 3 .3 V
6
4
2
Rev. 1.40
8 2
1 0 0
1 2 0
R (k W )
7
1 5 9
2 4 0
April 19, 2011
HT83F02
T vs. F (External RC) Chart Characteristics Curve
T v s . F C h a rt
1 .0 3
1 .0 2
(2 5 ° C )
1 .0 1
fO
S C
fO
S C
8 M H z , V
D D
= 3 .3 V
1 .0 0
0 .9 9
0 .9 8
9 0
2 5
-4 5
T (° C )
V vs. F (HIRC) Chart Characteristics Curve at 25°C - Trimmed at 5V
V v s . F C h a rt
1 6
1 4
1 2 M H z
F re q u e n c y (M H z )
1 2
1 0
8 M H z
8
6
4 M H z
4
2
Rev. 1.40
2 .5
3 .0
3 .5
4 .0
V
8
D D
(V )
4 .5
5 .0
5 .5
6 .0
April 19, 2011
HT83F02
V vs. F (HIRC) Chart Characteristics Curve at 25°C - Trimmed at 3V
V v s . F C h a rt
1 6
1 4
F re q u e n c y (M H z )
1 2
1 2 M H z
1 0
8
8 M H z
6
4
2
4 M H z
Rev. 1.40
2 .5
3 .0
3 .5
4 .0
V
9
D D
(V )
4 .5
5 .0
5 .5
6 .0
April 19, 2011
HT83F02
System Architecture
generated non-overlapping clocks, T1~T4. The Program Counter is incremented at the beginning of the T1
clock during which time a new instruction is fetched. The
remaining T2~T4 clocks carry out the decoding and execution functions. In this way, one T1~T4 clock cycle
forms one instruction cycle. Although the fetching and
execution of instructions takes place in consecutive instruction cycles, the pipelining structure of the
microcontroller ensures that instructions are effectively
executed in one instruction cycle. The exception to this
are instructions where the contents of the Program
Counter are changed, such as subroutine calls or
jumps, in which case the instruction will take one more
instruction cycle to execute.
A key factor in the high-performance features of the
Holtek range of microcontrollers is attributed to the internal system architecture. The range of devices take advantage of the usual features found within RISC
microcontrollers providing increased speed of operation
and enhanced performance. The pipelining scheme is
implemented in such a way that instruction fetching and
instruction execution are overlapped, hence instructions
are effectively executed in one cycle, with the exception
of branch or call instructions. An 8-bit wide ALU is used
in practically all operations of the instruction set. It carries out arithmetic operations, logic operations, rotation,
increment, decrement, branch decisions, etc. The internal data path is simplified by moving data through the
Accumulator and the ALU. Certain internal registers are
implemented in the Data Memory and can be directly or
indirectly addressed. The simple addressing methods of
these registers along with additional architectural features ensure that a minimum of external components is
required to provide a functional I/O control system with
maximum reliability and flexibility.
For instructions involving branches, such as jump or call
instructions, two machine cycles are required to complete instruction execution. An extra cycle is required as
the program takes one cycle to first obtain the actual
jump or call address and then another cycle to actually
execute the branch. The requirement for this extra cycle
should be taken into account by programmers in timing
sensitive applications.
Clocking and Pipelining
The main system clock, derived from either a Crystal,
ERC or IRC oscillator, is subdivided into four internally
O s c illa to r C lo c k
( S y s te m C lo c k )
P h a s e C lo c k T 1
P h a s e C lo c k T 2
P h a s e C lo c k T 3
P h a s e C lo c k T 4
P ro g ra m
C o u n te r
P ip e lin in g
P C
P C + 1
F e tc h In s t. (P C )
E x e c u te In s t. (P C -1 )
P C + 2
F e tc h In s t. (P C + 1 )
E x e c u te In s t. (P C )
F e tc h In s t. (P C + 2 )
E x e c u te In s t. (P C + 1 )
System Clocking and Pipelining
1
M O V A ,[1 2 H ]
3
C P L [1 2 H ]
2
C A L L D E L A Y
4
F e tc h In s t. 1
E x e c u te In s t. 1
F e tc h In s t. 2
E x e c u te In s t. 2
5
:
6
D E L A Y :
:
N O P
F e tc h In s t. 3
F lu s h P ip e lin e
F e tc h In s t. 6
E x e c u te In s t. 6
F e tc h In s t. 7
Instruction Fetching
Rev. 1.40
10
April 19, 2011
HT83F02
Program Counter
cause program branching, so an extra cycle is needed
to pre-fetch. Further information on the PCL register can
be found in the Special Function Register section.
During program execution, the Program Counter is used
to keep track of the address of the next instruction to be
executed. It is automatically incremented by one each
time an instruction is executed except for instructions,
such as ²JMP² or ²CALL², that demand a jump to a
non-consecutive Program Memory address. Note that
the Program Counter width varies with the Program
Memory capacity depending upon which device is selected. However, it must be noted that only the lower 8
bits, known as the Program Counter Low Register, are
directly addressable by user.
Stack
This is a special part of the memory which is used to
save the contents of the Program Counter only. The
stack has 8 levels and is neither part of the data nor part
of the program space, and can neither be read from nor
written to. The activated level is indexed by the Stack
Pointer, SP, which can also neither be read from nor
written to. At a subroutine call or interrupt acknowledge
signal, the contents of the Program Counter are pushed
onto the stack. At the end of a subroutine or an interrupt
routine, signaled by a return instruction, ²RET² or
²RETI², the Program Counter is restored to its previous
value from the stack. After a device reset, the Stack
Pointer will point to the top of the stack.
When executing instructions requiring jumps to
non-consecutive addresses such as a jump instruction,
a subroutine call, interrupt or reset, etc., the
microcontroller manages program control by loading the
required address into the Program Counter. For conditional skip instructions, once the condition has been
met, the next instruction, which has already been
fetched during the present instruction execution, is discarded and a dummy cycle takes its place while the correct instruction is obtained.
P ro g ra m
T o p o f S ta c k
The lower byte of the Program Counter, known as the
Program Counter Low register or PCL, is available for
program control and is a readable and writable register.
By transferring data directly into this register, a short
program jump can be executed directly, however, as
only this low byte is available for manipulation, the
jumps are limited to the present page of memory, that is
256 locations. When such program jumps are executed
it should also be noted that a dummy cycle will be inserted.
B o tto m
S ta c k L e v e l 1
S ta c k L e v e l 2
S ta c k
P o in te r
P ro g ra m
M e m o ry
S ta c k L e v e l 3
o f S ta c k
C o u n te r
S ta c k L e v e l 8
If the stack is full and an enabled interrupt takes place,
the interrupt request flag will be recorded but the acknowledge signal will be inhibited. When the Stack
Pointer is decremented, by RET or RETI, the interrupt
will be serviced. This feature prevents stack overflow allowing the programmer to use the structure more easily.
The lower byte of the Program Counter is fully accessible under program control. Manipulating the PCL might
Program Counter
Mode
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
Initial Reset
0
0
0
0
0
0
0
0
0
0
0
Timer Base Overflow
0
0
0
0
0
0
0
0
1
0
0
Timer Counter 0 Overflow
0
0
0
0
0
0
0
1
0
0
0
Timer Counter 1 Overflow
0
0
0
0
0
0
0
1
1
0
0
SIMA Interrupt
0
0
0
0
0
0
1
0
0
0
0
SIMB Interrupt
0
0
0
0
0
0
1
0
1
0
0
Skip
Program Counter + 2
Loading PCL
*10
*9
*8
@7
@6
@5
@4
@3
@2
@1
@0
Jump, Call Branch
#10
#9
#8
#7
#6
#5
#4
#3
#2
#1
#0
Return from Subroutine
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
Program Counter
Note:
*10~*0: Program counter bits
#10~#0: Instruction code bits
Rev. 1.40
S10~S0: Stack register bits
@7~@0: PCL bits
11
April 19, 2011
HT83F02
· Location 000H
However, when the stack is full, a CALL subroutine instruction can still be executed which will result in a stack
overflow. Precautions should be taken to avoid such
cases, which might cause unpredictable program
branching.
This vector is reserved for use by the device reset for
program initialisation. After a device reset is initiated, the
program will jump to this location and begin execution.
· Location 004H
This vector is used by the external interrupt. If the external interrupt pin on the device goes low, the program will jump to this location and begin execution if
the external interrupt is enabled and the stack is not
full.
Arithmetic and Logic Unit - ALU
The arithmetic-logic unit or ALU is a critical area of the
microcontroller that carries out arithmetic and logic operations of the instruction set. Connected to the main
microcontroller data bus, the ALU receives related instruction codes and performs the required arithmetic or
logical operations after which the result will be placed in
the specified register. As these ALU calculation or operations may result in carry, borrow or other status
changes, the status register will be correspondingly updated to reflect these changes. The ALU supports the
following functions:
· Location 008H
This vector is used by the 8-bit Timer 0. If a overflow
occurs, the program will jump to this location and begin execution if the timer interrupt is enabled and the
stack is not full.
· Location 00CH
This vector is used by the 8-bit Timer1. If a overflow
occurs, the program will jump to this location and begin execution if the timer interrupt is enabled and the
stack is not full.
· Arithmetic operations ADD, ADDM, ADC, ADCM,
SUB, SUBM, SBC, SBCM, DAA
· Location 010H
· Logic operations AND, OR, XOR, ANDM, ORM,
This vector is used by the SIMA Bus interrupt service
program. If the SIMA Bus interrupt resulting from a
slave address is matched or if 8 bits of data have been
received or transmitted successfully from the I2C interface, or 8 bits of data have been received or transmitted successful from SPI interface, the program will
jump to this location and begin execution if the interrupt is enabled and the stack is not full.
XORM, CPL, CPLA
· Rotation RRA, RR, RRCA, RRC, RLA, RL, RLCA,
RLC
· Increment and Decrement INCA, INC, DECA, DEC
· Branch decision JMP, SZ, SZA, SNZ, SIZ, SDZ, SIZA,
SDZA, CALL, RET, RETI
· Location 014H
Flash Program Memory
This vector is used by the SIMB Bus interrupt service
program. If the SIMB Bus interrupt resulting from a
slave address is matched or if 8 bits of data have been
received or transmitted successfully from the I2C interface, or 8 bits of data have been received or transmitted successful from SPI interface, the program will
jump to this location and begin execution if the interrupt is enabled and the stack is not full.
The Program Memory is the location where the user
code or program is stored. For this device series the
Program Memory is Flash type, which means it can be
programmed and re-programmed a large number of
times, allowing the user the convenience of code modification on the same device. By using the appropriate
programming tools, this Flash device offers users the
flexibility to conveniently debug and develop their applications while also offering a means of field programming
and updating.
0 0 0 H
0 0 4 H
Structure
0 0 8 H
The Program Memory has a capacity of 2K by 16 bits.
The Program Memory is addressed by the Program
Counter and also contains data, table information and
interrupt entries. Table data, which can be setup in any
location within the Program Memory, is addressed by
separate table pointer registers.
0 0 C H
0 1 0 H
0 1 4 H
Special Vectors
0 1 5 H
Within the Program Memory, certain locations are reserved for special usage such as reset and interrupts.
7 F F H
In itia lis a tio n
V e c to r
T im e B a s e
In te rru p t V e c to r
T im e r C o u n te r 0
In te rru p t V e c to r
T im e r C o u n te r 1
In te rru p t V e c to r
S IM A
In te rru p t V e c to r
S IM B
In te rru p t V e c to r
1 6 b its
Program Memory Structure
Rev. 1.40
12
April 19, 2011
HT83F02
The following diagram illustrates the addressing/data
flow of the look-up table.
Look-up Table
Any location within the Program Memory can be defined
as a look-up table where programmers can store fixed
data. To use the look-up table, table pointers are used to
setup the address of the data that is to be accessed from
the Program Memory. However, as some devices possess only a low byte table pointer and other devices possess both a high and low byte pointer it should be noted
that depending upon which device is used, accessing
look-up table data is implemented in slightly different
ways.
P ro g ra m C o u n te r
H ig h B y te
T B L H
H ig h B y te o f T a b le C o n te n ts
B y te o f T a b le C o n te n ts
Table Program Example
The following example shows how the table pointer and
table data is defined and retrieved from the devices.
This example uses raw table data located in the last
page which is stored there using the ORG statement.
The value at this ORG statement is ²700H² which refers
to the start address of the last page within the
2048´16-bit Program Memory of the microcontroller.
The table pointer is setup here to have an initial value of
²06H². This will ensure that the first data read from the
data table will be at the Program Memory address
²706H² or 6 locations after the start of the last page.
Note that the value for the table pointer is referenced to
the first address of the present page if the ²TABRDC[m]²
instruction is being used. The high byte of the table data
which in this case is equal to zero will be transferred to
the TBLH register automatically when the ²TABRDL [m]²
instruction is executed.
Any unused bits in this transferred higher order byte will
be read as ²0².
?
?
S p e c ifie d b y [m ]
L o w
Look-up Table
There are two Table Pointer Registers known as TBLP
and TBHP in which the lower order and higher order address of the look-up data to be retrieved must be respectively first written. The additional TBHP register allows
the complete address of the look-up table to be defined
and consequently allow table data from any address
and any page to be directly accessed. For this device,
after setting up both the low and high byte table pointers,
the table data can then be retrieved from any area of
Program Memory using the TABRDC [m] instruction or
from the last page of the Program Memory using the
TABRDL [m] instruction. When either of these instructions are executed, the lower order table byte from the
Program Memory will be transferred to the user defined
Data Memory register [m] as specified in the instruction.
The higher order table data byte from the Program
Memory will be transferred to the TBLH special register.
tempreg1 db
tempreg2 db
:
:
P ro g ra m
M e m o ry
T B L P
; temporary register #1
; temporary register #2
mov a,06h
; initialise table pointer - note that this address is referenced
mov tblp,a
:
:
; to the last page or present page
tabrdl
;
;
;
;
tempreg1
dec tblp
tabrdl
:
:
org 700h
dc
transfers value in table referenced by table pointer
to tempregl
data at prog. memory address ²706H² transferred to
tempreg1 and TBLH
; reduce value of table pointer by one
tempreg2
;
;
;
;
;
;
;
;
transfers value in table referenced by table pointer
to tempreg2
data at prog.memory address ²705H² transferred to
tempreg2 and TBLH
in this example the data ²1AH² is transferred to
tempreg1 and data ²0FH² to register tempreg2
the value ²00H² will be transferred to the high byte
register TBLH
; sets initial address of HT83F02 last page
00Ah, 00Bh, 00Ch, 00Dh, 00Eh, 00Fh, 01Ah, 01Bh
:
:
Rev. 1.40
13
April 19, 2011
HT83F02
recommended that simultaneous use of the table read
instructions should be avoided. However, in situations
where simultaneous use cannot be avoided, the interrupts should be disabled prior to the execution of any
main routine table-read instructions. Note that all table
related instructions require two instruction cycles to
complete their operation.
Because the TBLH register is a read-only register and
cannot be restored, care should be taken to ensure its
protection if both the main routine and Interrupt Service
Routine use table read instructions. If using the table
read instructions, the Interrupt Service Routines may
change the value of the TBLH and subsequently cause
errors if used again by the main routine. As a rule it is
Table Location
Instruction
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
TABRDC [m]
P10
P9
P8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
1
1
1
@7
@6
@5
@4
@3
@2
@1
@0
Table Location
Note:
*10~*0: Current Program ROM table
@7~@0: Write @7~@0 to TBLP pointer register
P10~P8: Write P12~P8 to TBHP pointer register
W r ite r C o n n e c to r
S ig n a ls
In Circuit Programming
The provision of Flash type Program Memory provides
the user with a means of convenient and easy upgrades
and modifications to their programs on the same device.
As an additional convenience, Holtek has provided a
means of programming the microcontroller in-circuit using a 5-pin interface. This provides manufacturers with
the possibility of manufacturing their circuit boards complete with a programmed or un-programmed
microcontroller, and then programming or upgrading the
program at a later stage. This enables product manufacturers to easily keep their manufactured products supplied with the latest program releases without removal
and re-insertion of the device.
MCU Programming
Pins
M C U P r o g r a m m in g
P in s
W r ite r _ V D D
V D D
R E S
R E S
D A T A
D A T A
C L K
C L K
W r ite r _ V S S
V S S
*
*
*
Function
PA0
Serial Data Input/Output
PA2
Serial Clock
RES
Device Reset
VDD
Power Supply
VSS
Ground
T o o th e r C ir c u it
Note: * may be resistor or capacitor. The resistance
of * must be greater than 1kW or the capacitance
of * must be less than 1nF.
The Program Memory can be programmed serially
in-circuit using this 5-wire interface. Data is downloaded
and uploaded serially on a single pin with an additional
line for the clock. Two additional lines are required for
the power supply and one line for the reset. The technical details regarding the in-circuit programming of the
devices are beyond the scope of this document and will
be supplied in supplementary literature.
Programmer Pin
MCU Pins
RES
PC0
DATA
PA0
CLK
PA2
Programmer and MCU Pins
During the programming process the RES pin will be
held low by the programmer disabling the normal operation of the microcontroller and taking control of the PA0
and PA2 I/O pins for data and clock programming purposes. The user must there take care to ensure that no
other outputs are connected to these two pins.
Rev. 1.40
14
April 19, 2011
HT83F02
Data Memory
Special Purpose Data Memory
The Data Memory is a volatile area of 8-bit wide RAM internal memory and is the location where temporary information is stored. Divided into two sections, the first of
these is an area of RAM where special function registers
are located. These registers have fixed locations and
are necessary for correct operation of the device. Many
of these registers can be read from and written to directly under program control, however, some remain
protected from user manipulation. The second area of
RAM Data Memory is reserved for general purpose use.
All locations within this area are read and write accessible under program control.
This area of Data Memory, is located in Bank, where
registers, necessary for the correct operation of the
microcontroller, are stored. Most of the registers are
both readable and writable but some are protected and
are readable only, the details of which are located under
the relevant Special Function Register section. Note
that for locations that are unused, any read instruction to
these addresses will return the value ²00H².
Special Function Registers
To ensure successful operation of the microcontroller,
certain internal registers are implemented in the Data
Memory area. These registers ensure correct operation
of internal functions such as timers, interrupts, etc., as
Structure
The Data Memory has a bank, known as Bank, which is
implemented in 8-bit wide RAM. The RAM Data Memory
is located in Bank 0 which is also subdivided into two sections, the Special Purpose Data Memory and the General
Purpose Data Memory. The length of these sections is
dictated by the type of microcontroller chosen.
0 0 H
0 1 H
0 2 H
0 3 H
0 4 H
0 5 H
0 6 H
0 7 H
0 8 H
0 9 H
0 A H
0 B H
0 C H
0 D H
0 E H
0 F H
1 0 H
1 1 H
1 2 H
1 3 H
1 4 H
1 5 H
1 6 H
1 7 H
1 8 H
1 9 H
1 A H
1 B H
1 C H
1 D H
1 E H
1 F H
2 0 H
2 1 H
2 2 H
2 3 H
2 4 H
2 5 H
2 6 H
2 7 H
2 8 H
2 9 H
2 A H
2 B H
2 C H
2 D H
2 E H
2 F H
3 0 H
The start address of the RAM Data Memory for all devices is the address ²00H², and the last Data Memory
address is ²FFH². Registers which are common to all
microcontrollers, such as ACC, PCL, etc., have the
same Data Memory address.
0 0 H
2 F H
3 0 H
F F H
S p e c ia l P u r p o s e
D a ta M e m o ry
G e n e ra l P u rp o s e
D a ta M e m o ry
(2 0 8 B y te s )
RAM Data Memory Structure
Note: Most of the RAM Data Memory bits can be
directly manipulated using the ²SET [m].i² and
²CLR [m].i² instructions with the exception of a
few dedicated bits. The RAM Data Memory can
also be accessed through the Memory Pointer
registers MP.
General Purpose Data Memory
All microcontroller programs require an area of
read/write memory where temporary data can be stored
and retrieved for use later. It is this area of RAM memory
that is known as General Purpose Data Memory. This
area of Data Memory is fully accessible by the user program for both read and write operations. By using the
²SET [m].i² and ²CLR [m].i² instructions individual bits
can be set or reset under program control giving the
user a large range of flexibility for bit manipulation in the
Data Memory.
F F H
IA R 0
M P 0
A C C
P C L
T B L P
T B L H
W D T S
S T A T U S
IN T C
T M R 0
T M R 0 C
T M R 1
T M R 1 C
P A
P A C
P B
P B C
P C
P C C
IN T C H
S IM
S IM
S IM
S IM A R B
D
D
P W
P W
P W
V
C 0 B
C 1 B
D R B
/S IM C 2 B
A L
A H
M C
M L
M H
O L
S IM
S IM
S IM
S IM A R A
P C
C 0 A
C 1 A
D R A
/S IM C 2 A
P H C
U s e r D a ta R A M
: U n u s e d ,
re a d a s "0 0 "
Special Purpose Data Memory Structure
Rev. 1.40
15
April 19, 2011
HT83F02
operation to these registers but rather to the memory location specified by their corresponding Memory Pointer,
MP0. As the Indirect Addressing Registers are not physically implemented, reading the Indirect Addressing
Registers indirectly will return a result of ²00H² and writing to the registers indirectly will result in no operation.
well as external functions such as I/O data control. The
location of these registers within the Data Memory begins at the address ²00H². Any unused Data Memory locations between these special function registers and the
point where the General Purpose Memory begins is reserved and attempting to read data from these locations
will return a value of ²00H².
Memory Pointer - MP0
Indirect Addressing Register - IAR0
For all devices, two Memory Pointers, known as MP0 is
provided. These Memory Pointers are physically implemented in the Data Memory and can be manipulated in
the same way as normal registers providing a convenient way with which to address and track data. When
any operation to the relevant Indirect Addressing Registers is carried out, the actual address that the
microcontroller is directed to, is the address specified by
the related Memory Pointer.
The Indirect Addressing Registers, IAR0, although having their locations in normal RAM register space, do not
actually physically exist as normal registers. The
method of indirect addressing for RAM data manipulation uses these Indirect Addressing Registers and Memory Pointers, in contrast to direct memory addressing,
where the actual memory address is specified. Actions
on the IAR0 registers will result in no actual read or write
The following example shows how to clear a section of four Data Memory locations already defined as locations adres1
to adres4.
data .section ¢data¢
adres1
db ?
adres2
db ?
adres3
db ?
adres4
db ?
block
db ?
code .section at 0 ¢code¢
org 00h
start:
mov
mov
mov
mov
a,04h
block,a
a,offset adres1
mp0,a
; setup size of block
loop:
clr
inc
sdz
jmp
IAR0
mp0
block
loop
; clear the data at address defined by MP0
; increment memory pointer
; check if last memory location has been cleared
; Accumulator loaded with first RAM address
; setup memory pointer with first RAM address
continue:
The important point to note here is that in the example shown above, no reference is made to specific Data Memory
addresses.
Rev. 1.40
16
April 19, 2011
HT83F02
Accumulator - ACC
By writing directly to this register, the appropriate division ratio for the Watchdog Timer clock source can be
setup. Note that only the lower 3 bits are used to set division ratios between 1 and 128.
The Accumulator is central to the operation of any
microcontroller and is closely related with operations
carried out by the ALU. The Accumulator is the place
where all intermediate results from the ALU are stored.
Without the Accumulator it would be necessary to write
the result of each calculation or logical operation such
as addition, subtraction, shift, etc., to the Data Memory
resulting in higher programming and timing overheads.
Data transfer operations usually involve the temporary
storage function of the Accumulator; for example, when
transferring data between one user defined register and
another, it is necessary to do this by passing the data
through the Accumulator as no direct transfer between
two registers is permitted.
Status Register - STATUS
This 8-bit register contains the zero flag (Z), carry flag
(C), auxiliary carry flag (AC), overflow flag (OV), power
down flag (PDF), and watchdog time-out flag (TO).
These arithmetic/logical operation and system management flags are used to record the status and operation of
the microcontroller.
With the exception of the TO and PDF flags, bits in the
status register can be altered by instructions like most
other registers. Any data written into the status register
will not change the TO or PDF flag. In addition, operations related to the status register may give different results due to the different instruction operations. The TO
flag can be affected only by a system power-up, a WDT
time-out or by executing the ²CLR WDT² or ²HALT² instruction. The PDF flag is affected only by executing the
²HALT² or ²CLR WDT² instruction or during a system
power-up.
Program Counter Low Register - PCL
To provide additional program control functions, the low
byte of the Program Counter is made accessible to programmers by locating it within the Special Purpose area
of the Data Memory. By manipulating this register, direct
jumps to other program locations are easily implemented. Loading a value directly into this PCL register
will cause a jump to the specified Program Memory location, however, as the register is only 8-bit wide, only
jumps within the current Program Memory page are permitted. When such operations are used, note that a
dummy cycle will be inserted.
The Z, OV, AC and C flags generally reflect the status of
the latest operations.
· C is set if an operation results in a carry during an ad-
dition operation or if a borrow does not take place during a subtraction operation; otherwise C is cleared. C
is also affected by a rotate through carry instruction.
Look-up Table Registers - TBLP, TBLH
These two special function registers are used to control
operation of the look-up table, which is stored in the Program Memory. TBLP is the table pointer and indicates
the location where the table data is located. Its value
must be setup before any table read commands are executed. Its value can be changed, for example using the
²INC² or ²DEC² instructions, allowing for easy table data
pointing and reading. TBLH is the location where the
high order byte of the table data is stored after a table
read data instruction has been executed. Note that the
lower order table data byte is transferred to a user defined location.
· AC is set if an operation results in a carry out of the
Watchdog Timer Register - WDTS
· TO is cleared by a system power-up or executing the
low nibbles in addition, or no borrow from the high nibble into the low nibble in subtraction; otherwise AC is
cleared.
· Z is set if the result of an arithmetic or logical operation
is zero; otherwise Z is cleared.
· OV is set if an operation results in a carry into the high-
est-order bit but not a carry out of the highest-order bit,
or vice versa; otherwise OV is cleared.
· PDF is cleared by a system power-up or executing the
²CLR WDT² instruction. PDF is set by executing the
²HALT² instruction.
²CLR WDT² or ²HALT² instruction. TO is set by a
WDT time-out.
The Watchdog feature of the microcontroller provides
an automatic reset function giving the microcontroller a
means of protection against spurious jumps to incorrect
Program Memory addresses. To implement this, a timer
is provided within the microcontroller which will issue a
reset command when its value overflows. To provide
variable Watchdog Timer reset times, the Watchdog
Timer clock source can be divided by various division ratios, the value of which is set using the WDTS register.
Rev. 1.40
In addition, on entering an interrupt sequence or executing a subroutine call, the status register will not be
pushed onto the stack automatically. If the contents of
the status registers are important and if the subroutine
can corrupt the status register, precautions must be
taken to correctly save it.
17
April 19, 2011
HT83F02
b 7
T O
P D F
O V
Z
A C
b 0
C
S T A T U S R e g is te r
A r
C a
A u
Z e
ith m e
r r y fla
x ilia r y
r o fla g
O v e r flo w
g
tic /L o g ic O p e r a tio n F la g s
c a r r y fla g
fla g
S y s te m M
P o w e r d o w
W a tc h d o g
N o t im p le m
a n
n
tim
e
a g e m e n t F la g s
fla g
e - o u t fla g
n te d , re a d a s "0 "
Status Register
Interrupt Control Register - INTC, INTCH
Input/Output Ports and Control Registers
Two 8-bit register, known as the INTC and INTCH registers, controls the operation of both external and internal
timer interrupts. By setting various bits within these registers using standard bit manipulation instructions, the
enable/disable function of the external and timer interrupts can be independently controlled. A master interrupt bit within this register, the EMI bit, acts like a global
enable/disable and is used to set all of the interrupt enable bits on or off. This bit is cleared when an interrupt
routine is entered to disable further interrupt and is set
by executing the ²RETI² instruction.
Within the area of Special Function Registers, the I/O
registers and their associated control registers play a
prominent role. All I/O ports have a designated register
correspondingly labeled as PA, PB and PC. These labeled I/O registers are mapped to specific addresses
within the Data Memory as shown in the Data Memory
table, which are used to transfer the appropriate output
or input data on that port. With each I/O port there is an
associated control register labeled PAC, PBC and PCC,
also mapped to specific addresses with the Data Memory. The control register specifies which pins of that port
are set as inputs and which are set as outputs. To setup
a pin as an input, the corresponding bit of the control
register must be set high, for an output it must be set
low. During program initialization, it is important to first
setup the control registers to specify which pins are outputs and which are inputs before reading data from or
writing data to the I/O ports. One flexible feature of these
registers is the ability to directly program single bits using the ²SET [m].i² and ²CLR [m].i² instructions. The
ability to change I/O pins from output to input and vice
versa by manipulating specific bits of the I/O control registers during normal program operation is a useful feature of these devices.
Note: In situations where other interrupts may require
servicing within present interrupt service routines, the EMI bit can be manually set by the program after the present interrupt service routine
has been entered.
Timer Registers
All devices contain two 8-bit Timers whose associated
registers are known as TMR0 and TMR1 which is the location where the associated timer's 8-bit value is located. Their associated control registers, known as
TMR0C and TMR1C, contain the setup information for
these timers.
Port C Pull-high Control Register - PCPHC
Note that all timer registers can be directly written to in
order to preload their contents with fixed data to allow
different time intervals to be setup.
b 7
P C P H C 2
Port C pull-high control register, PCPHC, is used to set
the Port C pull high function.
P C P H C 1
b 0
P C P H C 0
P C P H C
R e g is te r
C o n tr o l th e P o r t C P u ll- H ig h
1 : e n a b k e
0 : d is a b le - d e fa u lt
N o t im p le m e n te d , r e a d a s " 0 "
Port C Pull-High Control Register
Rev. 1.40
18
April 19, 2011
HT83F02
Voice Control and Audio output Registers DAL, DAH, VOL
used for input and output operations. For input operation, these ports are non-latching, which means the inputs must be ready at the T2 rising edge of instruction
²MOV A,[m]², where m denotes the port address. For
output operation, all the data is latched and remains unchanged until the output latch is rewritten.
The devices include a single 12-bit current type DAC
function for driving an external 8W speaker through an
external NPN transistor or Power Amplifier. The programmer must writer the voice data to these DAL/DAH
registers. The programmer can control the DAC volume
with 8-levels via the VOL register.
Pull-high Resistors
Many product applications require pull-high resistors for
their switch inputs usually requiring the use of an external resistor. To eliminate the need for these external resistors, all I/O pins, when configured as an input have
the capability of being connected to an internal pull-high
resistor. These pull-high resistors are selectable via
configuration or software options and are implemented
using a weak PMOS transistor. Note that if the pull-high
option is selected, then all I/O pins on that port will be
connected to pull-high resistors, individual pins can be
selected for pull-high resistor options.
Pulse Width Modulator Registers PWMC, PWML, PWMH
Each device contains a single 12-bit PWM function for
driving an external 8W speaker. The programmer must
writer the voice data to PWML/PWMH register. The programmer can control the PWM volume with 9-levels via
the VOL register.
Serial Interface Module(SIM) Registers SIMC0A/B, SIMC1A/B, SIMC2A/B, SIMARA/B,
SIMDRA/B
Port A Wake-up
Each SIM contains SPI and I2C function for communicating with other microcontroller or SPI Flash Memory. All
devices contain an integrated I2C and SPI bus which interfaces to the external shared pins SDA, SCL and
SCSB, SCK, SDI, SDO with PB on the microcontroller.
The I2C correct setup and data transfer operation of this
2-line bidirectional bus utilizes 4 special function registers. The SIMARA/B register sets the slave address of
the device while the SIMC0A/B is the control register
that enables or disables the device as well as select
whether it is in I2C or SPI mode. The SIMC1A/B register
is the I2C status register while the SIMDRA/B register is
the input/output data register. The SPI correct setup and
data transfer operation of this 3-line bidirectional bus utilizes 3 special function registers. The SIMC0A/B is the
control register that enables or disables the device as
well as select whether it is in I2C or SPI mode. The
SIMC2A/B register is the SPI status register while the
SIMDRA/B register is the input/output data register.
Each device has a HALT instruction enabling the
microcontroller to enter a Power Down Mode and preserve power, a feature that is important for battery and
other low-power applications. Various methods exist to
wake-up the microcontroller, one of which is to change
the logic condition on one of the Port A pins from high to
low. After a ²HALT² instruction forces the microcontroller
into entering a HALT condition, the processor will remain idle or in a low-power state until the logic condition
of the selected wake-up pin on Port A changes from high
to low. This function is especially suitable for applications that can be woken up via external switches. Note
that each pin on Port A can be selected individually to
have this wake-up feature.
I/O Port Control Registers
Each I/O port has its own control register PAC, PBC and
PCC, to control the input/output configuration. With this
control register, each CMOS output or input with or without pull-high resistor structures can be reconfigured dynamically under software control. Each pin of the I/O
ports is directly mapped to a bit in its associated port
control register. For the I/O pin to function as an input,
the corresponding bit of the control register must be written as a ²1². This will then allow the logic state of the input pin to be directly read by instructions. When the
corresponding bit of the control register is written as a
²0², the I/O pin will be setup as a CMOS output. If the pin
is currently setup as an output, instructions can still be
used to read the output register. However, it should be
noted that the program will in fact only read the status of
the output data latch and not the actual logic status of
the output pin.
Input/Output Ports
Holtek microcontrollers offer considerable flexibility on
their I/O ports. With the input or output designation of every pin fully under user program control, pull-high options for all ports and wake-up options on certain pins,
the user is provided with an I/O structure to meet the
needs of a wide range of application possibilities.
Depending upon which device or package is chosen,
the microcontroller range provides from 19 bidirectional
input/output lines labeled with port names PA, PB, PC
etc. These I/O ports are mapped to the Data Memory
with specific addresses as shown in the Special Purpose Data Memory table. All of these I/O ports can be
Rev. 1.40
19
April 19, 2011
HT83F02
C o n tr o l B it
D a ta B u s
Q
D
W r ite C o n tr o l R e g is te r
C K
P A 0 ~ P A 7
R e a d C o n tr o l R e g is te r
D a ta B it
Q
D
W r ite D a ta R e g is te r
C K
S
Q
M
R e a d D a ta R e g is te r
S y s te m
D D
W e a k
P u ll- u p
Q
S
C h ip R e s e t
V
P u ll- H ig h
O p tio n
U
X
W a k e -u p
W a k e - u p O p tio n
PA Input/Output Port
D a ta B u s
D
W r ite C o n tr o l R e g is te r
Q
C K
R e a d C o n tr o l R e g is te r
W r ite D a ta R e g is te r
P B 0
P B 1
P B 2
P B 3
P B 4
P B 5
P B 6
P B 7
R e a d
/S D
/S C
/S D
/S C
/S D
/S C
/S D
/S C
D a
O B /S
K B /S
IB
S B
O A /S
K A /S
IA
S A
ta R e
D A B
C L B
D A A
C L A
g is te r
P B 0
P B 1
P B 2
P B 3
P B 4
P B 5
P B 6
P B 7
D a ta B it
Q
D
C K
S
D D
W e a k
P u ll- u p
Q
S
C h ip R e s e t
V
P u ll- H ig h
O p tio n
C o n tr o l B it
Q
M
M
U
U
/S D
/S C
/S D
/S C
/S D
/S C
/S D
/S C
O B /S
K B /S
IB
S B
O A /S
K A /S
IA
S A
D A B
C L B
D A A
C L A
X
A n a lo g S w itc h O p tio n
X
PB Input/Output Port
Pin-shared Functions
· Serial interface module
The flexibility of the microcontroller range is greatly enhanced by the use of pins that have more than one function. Limited numbers of pins can force serious design
constraints on designers but by supplying pins with
multi-functions, many of these difficulties can be overcome. For some pins, the chosen function of the
multi-function I/O pins is set by configuration options
while for others the function is set by application program control.
The device pins, PB4~PB7, are pin-shared with pins
SDAA, SCLA, SCSA, SCKA, SDIA, SDOA. The
choice of which function is used is selected using the
SIMC0A register.
· I/O pin structures
The following diagrams illustrate the I/O pin internal
structures. As the exact logical construction of the I/O
pin may differ from these drawings, they are supplied
as a guide only to assist with the functional understanding of the I/O pins.
Note also that the specified pins refer to the largest
device package, therefore not all pins specified will
exist on all devices.
· Serial interface module
The device pins, PB0~PB3, are pin-shared with pins
SDAB, SCLB, SCSB, SCKB, SDIB, SDOB. The
choice of which function is used is selected using the
SIMC0B register.
Rev. 1.40
20
April 19, 2011
HT83F02
Programming Considerations
Configuring the Timer Input Clock Source
Within the user program, one of the first things to consider is port initialization. After a reset, all of the I/O data
and port control registers will be set high. This means
that all I/O pins will default to an input state, the level of
which depends on the other connected circuitry and
whether pull-high options have been selected. If the port
control registers, PAC, PBC, PCC etc., are then programmed to setup some pins as outputs, these output
pins will have an initial high output value unless the associated port data registers, PA, PB, PC etc., are first
programmed. Selecting which pins are inputs and which
are outputs can be achieved byte-wide by loading the
correct values into the appropriate port control register
or by programming individual bits in the port control register using the ²SET [m].i² and ²CLR [m].i² instructions.
Note that when using these bit control instructions, a
read-modify-write operation takes place. The
microcontroller must first read in the data on the entire
port, modify it to the required new bit values and then rewrite this data back to the output ports.
The clock source for the 8-bit timers is the system clock
divided by four. The 8-bit timer clock source is also first divided by a, the division ratio of which is conditioned by the
three lower bits of the associated timer control register.
Timer Registers - TMR0, TMR1
The timer registers are special function registers located
in the special purpose Data Memory and is the place
where the actual timer value is stored. All devices contain two 8-bit timers, whose registers are known as
TMR0 and TMR1. The value in the timer registers increases by one each time an internal clock pulse is received. The timer will count from the initial value loaded
by the preload register to the full count of FFH for the
8-bit timer at which point the timer overflows and an internal interrupt signal is generated. The timer value will
then be reset with the initial preload register value and
continue counting.
S y s te m
Port A has the additional capability of providing wake-up
functions. When the device is in the Power Down Mode,
various methods are available to wake the device up.
One of these is a high to low transition of any of the Port
A pins. Single or multiple pins on Port A can be setup to
have this function.
C lo c k
T 1
T 2
T 3
T 4
T 1
T 2
T 3
T 4
P o rt D a ta
W r ite to P o r t
R e a d fro m
P o rt
Read/Write Timing
Note that to achieve a maximum full range count of FFH
for the 8-bit timer, the preload registers must first be
cleared to all zeros. It should be noted that after
power-on, the preload registers will be in an unknown
condition. Note that if the Timer Counters are in an OFF
condition and data is written to their preload registers,
this data will be immediately written into the actual counter. However, if the counter is enabled and counting, any
new data written into the preload data register during
this period will remain in the preload register and will
only be written into the actual counter the next time an
overflow occurs. Note also that when the timer registers
are read, the timer clock will be blocked to avoid errors,
however, as this may result in certain timing errors, programmers must take this into account.
Timers
The provision of timers form an important part of any
microcontroller, giving the designer a means of carrying
out time related functions. These devices contain two
count up timers of 8-bit capacity. The provision of an internal prescaler to the clock circuitry of the timer gives
added range to the timer.
There are two types of register related to each Timer.
The first is the register that contains the actual value of
the timer and into which an initial value can be
preloaded. Reading from this register retrieves the contents of the Timer. All devices can have the timer clock
configured to come from the internal clock source.
D a ta B u s
P r e lo a d R e g is te r
T 1 P S C 2 ~ T 1 P S C 0
T 0 P S C 2 ~ T 0 P S C 0
fS
Y S
P r e s c a le r
(1 /2 ~ 1 /2 5 6 )
T 1 T M 1
T 0 T M 1
R e lo a d
T 1 T M 0
T 0 T M 0
T im e r M o d e C o n tr o l
T im e r
T 0 O N
T 1 O N
8 - B it C o u n te r
O v e r flo w
to In te rru p t
8-bit Timer Structure
Rev. 1.40
21
April 19, 2011
HT83F02
Timer Control Registers - TMR0C, TMR1C
the Timer increments by one. When it is full and overflows, an interrupt signal is generated and the Timer will
reload the value already loaded into the preload register
and continue counting. The interrupt can be disabled by
ensuring that the Timer Interrupt Enable bit in the Interrupt Control Register, INTC, is reset to zero.
Each timer has its respective timer control register,
known as TMR0C and TMR1C. It is the timer control
register together with their corresponding timer registers
that control the full operation of the timers. Before the
timers can be used, it is essential that the appropriate
timer control register is fully programmed with the right
data to ensure its correct operation, a process that is
normally carried out during program initialization. Bits 7
and 6 of the Timer Control Register, must be set to the
required logic levels. Bit 6 of the registers must always
be written with a ²1², and bit 7 must always be written
with a ²0². The timer-on bit, which is bit 4 of the Timer
Control Register and known as T0ON/ T1ON, depending upon which timer is used, provides the basic on/off
control of the respective timer. setting the bit high allows
the timer to run, clearing the bit stops the timer. For the
8-bit timers, which have prescalers, bits 0~2 of the
Timer Control Register determines the division ratio of
the input clock prescaler.
Prescaler
All of the 8-bit timers possess a prescaler. Bits 0~2 of
their associated timer control register, define the
pre-scaling stages of the internal clock source of the
Timer. The Timer overflow signal can be used to generate signals for the Timer interrupt.
Programming Considerations
The internal system clock is used as the timer clock
source and is therefore synchronized with the overall
operation of the microcontroller. In this mode, when the
appropriate timer register is full, the microcontroller will
generate an internal interrupt signal directing the program flow to the respective internal interrupt vector.
Configuring the Timer
When the Timer is read, the clock is blocked to avoid errors, however as this may result in a counting error, this
should be taken into account by the programmer. Care
must be taken to ensure that the timers are properly initialized before using them for the first time. The associated timer enable bits in the interrupt control register must
be properly set otherwise the internal interrupt associated
with the timer will remain inactive. The edge select, timer
mode and clock source control bits in timer control register must also be correctly set to ensure the timer is properly configured for the required application. It is also
important to ensure that an initial value is first loaded into
the timer registers before the timer is switched on; this is
because after power-on the initial values of the timer registers are unknown. After the timer has been initialized
the timer can be turned on and off by controlling the enable bit in the timer control register.
The Timer is used to measure fixed time intervals, providing an internal interrupt signal each time the Timer
overflows. To do this the Operating Mode Select bit pair
in the Timer Control Register must be set to the correct
value as shown.
Control Register Operating Mode
Select Bits
Bit7 Bit6
1
0
The internal clock, fSYS, is used as the Timer clock. However, this clock source is further divided by a prescaler,
the value of which is determined by the Prescaler Rate
Select bits, which are bits 0~2 in the Timer Control Register. After the other bits in the Timer Control Register
have been setup, the enable bit, which is bit 4 of the
Timer Control Register, can be set high to enable the
Timer to run. Each time an internal clock cycle occurs,
P r e s c a le r O u tp u t
In c re m e n t
T im e r C o n tr o lle r
T im e r + 1
T im e r + 2
T im e r + N
T im e r + N
+ 1
Timer Mode Timing Diagram
Rev. 1.40
22
April 19, 2011
HT83F02
b 7
T n M 1 T n M 0
T n O N
b 0
T n P S C 2 T n P S C 1 T n P S C 0
T M R 0 C /T M R 1 C
T im e r P r e s c a
T 0 P S C 2 T 0
T 1 P S C 2 T 1
0
0
0
0
1
1
1
1
R e g is te r
le r R a te S e le c t
P S C 1
T 0 P S C 0
P S C 1
T 1 P S C 0
0
0
0
1
1
0
1
1
0
0
0
1
1
0
1
1
T im e r
1 :2
1 :4
1 :8
1 :1
1 :3
1 :6
1 :1
1 :2
N o t im p le m e n t e d , r e a d a s " d o n 't c a r e "
R a te
6
2
4
2 8
5 6
T im e r C o u n tin g E n a b le
1 : e n a b le
0 : d is a b le
N o t im p le m e n te d , r e a d a s " 0 "
O p e r a tin g M o d e S e le c t
T 0 T M 0
T 0 T M 1
T 1 T M 0
T 1 T M 1
n o
0
0
n o
1
0
tim
0
1
1
1
n o
m o d
m o d
e r m
m o d
e a v a ila b le
e a v a ila b le
o d e
e a v a ila b le
Timer Control Register (n=0 or 1)
Timer Program Example
The following example program section is based on the device, which contain two 8-bit timers. Programming the timer
for other devices is conducted in a very similar way. The program shows how the timer registers are setup along with
how the interrupts are enabled and managed. Points to note in the example are how, for the 8-bit timer. Note how the
timer is turned on by setting bit 4 of the respective timer control register. The timer can be turned off in a similar way by
clearing the same bit. This example program sets the timer to be in the timer mode which uses the internal fsys as their
clock source, and produce a timer 0 interrupt per 1ms.
#include HT83F02.inc
jmp begin
:
org 04h
;
reti
org 08h
;
jmp tmr0int
;
org 0Ch
reti
org 10h
reti
org 14h
reti
:
;
Tmr0int:
:
;
:
reti
:
begin:
;
mov a,06h
;
mov tmr0,a
;
mov a,094
;
mov tmr0c,a
;
;
mov a,05h
;
mov intc,a
;
Rev. 1.40
time base vector
timer 0 interrupt vector
jump here when timer 0 overflows every 1ms
internal timer 0 interrupt routine
timer 0 main program placed here
setup timer 0 registers
setup timer 0 low byte
flow byte must be setup before high byte
setup timer 0 control register
setup timer mode and clock source is fsys/32 prescaler
setup interrupt register
enable global interrupt
enable timer 0 interrupt
23
April 19, 2011
HT83F02
Time Base
The Time Base function will generate a regular interrupt
signal synchronised to the system clock which can be
used by the application as a time base signal.
flag is the TBF flag in the same register. A time base of
1ms will therefor be generated from a system clock of
4MHz and a time base of 0.5ms will be generated from a
system clock source of 8MHz.
Time Base Operation
Time base Example
The Time Base operation is a very simple function for
the generation of a regular time signal. This is implemented by generating a regular interrupt signal whose
enable/disabled and request flags are in the INTC register. The clock source for the time base is the internal
S y s te m
C lo c k /4
¸
1 0 2 4
The following example program section is based on the
device. The program shows how the Time Base registers are setup along with how the interrupts are enabled
and managed. The points to note in the example are
how the Time Base is turned on by setting bit 4 of the
INTC register. The Time Base can be turned off in a similar way by clearing the same bit. This example program
sets the Time Base which uses the internal system clock
as their clock source, and produces a time base interrupt every 0.5ms from a system source clock of 8MHz.
O v e r flo w
to In te rru p t
fSYS/4 clock source, which is then divided internally by a
value of 1024. It is this divided signal that generates the
internal interrupt. The Time Base Interrupt is enabled by
the ETBI bit in the INTC register and interrupt request
#include HT83F02.inc
jmp begin
:
org 04h
jmp time_base_int
org 08h
reti
org 0Ch
reti
org 10h
reti
org 14h
reti
:
; time base vector
; jump here when time base overflows per 0.5ms
; time base interrupt routine
time_base_int:
:
; time base main program placed here
:
reti
:
begin:
mov
mov
Rev. 1.40
a,03h
intc,a
; setup interrupt register
; enable global and time base interrupt
; enable time base
24
April 19, 2011
HT83F02
Serial Interface
The device contains both SPI and I2C serial interface
functions, which allows two methods of easy communication with external peripheral hardware. As the SPI and
I2C function share the same external pins and internal
registers their function must first be chosen by selecting
the correct configuration option.
Serial Data Output lines, SCK is the Serial Clock line
and SCS is the Slave Select line. As the SPI interface
pins are pin-shared with segment pins and with the I2C
function pins, the SPI interface must first be enabled
by selecting the correct configuration option. After the
SPI configuration option has been selected it can then
also be selected using the SIMEN bit in the SIMC0
register.
SPI Interface
The SPI interface is often used to communicate with external peripheral devices such as sensors, Flash or
EEPROM memory devices etc. Originally developed by
Motorola, the four line SPI interface is a synchronous
serial data interface that has a relatively simple communication protocol simplifying the programming requirements when communicating with external hardware
devices.
The SPI function in this device offers the following features:
¨
Full duplex synchronous data transfer
¨
Both Master and Slave modes
¨
LSB first or MSB first data transmission modes
¨
Transmission complete flag
Several other configuration options also exist to setup
various SPI interface options as follows:
· SPI Interface Operation
The SPI interface is a full duplex synchronous serial
data link. Communication between devices connected to the SPI interface is carried out in a
slave/master mode with all data transfer initiations being implemented by the master. Multiple slave devices
can be connected to the SPI serial bus with each device controlled using its slave select line. The SPI is a
four line interface with pin names SDI, SDO, SCK and
SCS. Pins SDI and SDO are the Serial Data Input and
¨
SPI pin enabled
¨
WCOL bit enabled or disabled
¨
CSEN bit enabled or disabled
The status of the SPI interface pins is determined
by a number of factors, whether the device is in
master or slave mode and upon the condition of certain control bits such as CSEN and SIMEN.
D a ta B u s
S IM D R
( R e c e iv e d D a ta R e g is te r )
D 7 D 6 D 5 D 4 D 3 D 2 D 1 D 0
M
X
M L S
In te r n a l B a u d R a te C lo c k
S C K
E N
C lo c k P o la r ity
a n d , s ta rt
B u ffe r
S D O
S IM E N
M
U
X
M
a n d , s ta rt
S D O
U
S D I
U
X
M a s te r o r S la v e
S IM E N
a n d , s ta rt
E N
T R F
C 0 C 1 C 2
In te r n a l B u s y F la g
S IM E N
A N D
W r ite S B D R
W r ite S IM D R
W r ite S IM D R
W C O L F la g
E n a b le /D is a b le
S C S
M a s te r o r S la v e
S IM E N
C S E N
Block Diagram
Rev. 1.40
25
April 19, 2011
HT83F02
Master (SIMEN=1)
Slave (SIMEN=1)
Master/Salve
(SIMEN=0)
CSEN=1
CSEN=0
CSEN=0
SCS line=0
(CSEN=1)
SCS line=1
(CSEN=1)
SCS
Z
L
Z
Z
I, Z
I, Z
SDO
Z
O
O
O
O
Z
SDI
Z
I, Z
I, Z
I, Z
I, Z
Z
Z
L(CPOL=1)
H(CPOL=0)
L(CPOL=1)
H(CPOL=0)
I, Z
I, Z
Z
SCK
²Z² floating, ²H² output high, ²L² output low, ²I² Input, ²O²output level, ²I,Z² input floating (no pull-high)
SPI Interface Pin Status
· SPI Registers
The SIMDR A/B register is used to store the data being transmitted and received. There are two control
registers associated with the SPI interface, SIMC0
A/B and SIMC2 A/B and one data register known as
SIMDRA/B. The SIMC1 A/B register is not used by the
SPI function. Register SIMC0 A/B is used to control
the enable/disable function, the power down control
and to set the data transmission clock frequency. Register SIMC2 A/B is used for other control functions
such as LSB/MSB selection, write collision flag etc.
The following gives further explanation of each bit:
¨
SIMEN A/B
The SIMEN A/B bit is the overall on/off control for
the SPI interface. When the SIMEN A/B bit is
cleared to zero to disable the SPI interface, the SDI,
SDO A/B, SCK A/B and SCS A/B lines will be in a
floating condition and the SPI operating current will
be reduced to <0.1mA at 5V. When the bit is high the
SPI interface is enabled. Note that when the SIMEN
A/B bit changes from low to high the contents of the
SPI control registers will be in an unknown condition
and should therefore be initialised by the application program.
¨
SIM0 A/B~SIM2 A/B
These three bits control the Master/Slave selection
and also setup the SPI interface clock speed when
in the Master Mode. The SPI clock is a function of
the system clock whether it be RC type or Crystal
type. If the Slave Mode is selected then the clock
will be supplied by the external Master device.
The following gives further explanation of each bit:
¨
TRF A/B
The TRF A/B bit is the Transmit/Receive Complete
flag and is cleared by the application program and
can be used to generate an interrupt. When the bit
is high the data has been transmitted or received. If
the bit is low the data is being transmitted or has not
yet been received.
Rev. 1.40
¨
WCOL A/B
The WCOL A/B bit is used to detect if a data collision has occurred. If this bit is high it means that
data has been attempted to be written to the SMDR
A/B register during a data transfer operation. This
writing operation will be ignored if data is being
transferred. The bit can be cleared by the application program. Note that using the CSEN A/B bit can
be disabled or enabled via configuration option.
¨
CSEN A/B
The CSEN A/B bit is used as an on/off control for the
SCS A/B pin. If this bit is low then the SCS A/B pin
will be disabled and placed into a floating condition.
If the bit is high the SCS A/B pin will be enabled and
used as a select pin.
¨
MLS A/B
The MLS A/B is used to select how the data is transferred, either MSB or LSB first. Setting the bit high
will select MSB first and low for LSB first.
Note that the SIMC2 A/B register is the same as the
SIMAR A/B register used by the I2C interface.
· SPI Communication
After the SPI interface is enabled by setting the
SIMEN A/B bit high, then in the Master Mode, when
data is written to the SIMDR A/B register, transmission/reception will begin simultaneously. When the
data transfer is complete, the TRF A/B flag will be set
automatically. In the Slave Mode, when the clock signal from the master has been received, any data in the
SIMDR register will be transmitted and any data on
the SDI A/B pin will be shifted into the SIMDR A/B register. The master should output an SCS A/B signal before a clock signal is provided and slave data transfers
should be enabled/disabled before/after an SCS A/B
signal is received.
26
April 19, 2011
HT83F02
S IM E N = 1 , C S E N = 0 ( E x te r n a l P u ll- H ig h )
S C S
S IM E N , C S E N = 1
S C K (C K P O L B = 1 , C K E G = 0 )
S C K (C K P O L B = 0 , C K E G = 0 )
S C K (C K P O L B = 1 , C K E G = 1 )
S C K (C K P O L B = 0 , C K E G = 1 )
S D O
(C K E G = 0 )
D 7 /D 0
D 6 /D 1
D 5 /D 2
D 4 /D 3
D 3 /D 4
D 2 /D 5
D 1 /D 6
D 0 /D 7
S D O
(C K E G = 1 )
D 7 /D 0
D 6 /D 1
D 5 /D 2
D 4 /D 3
D 3 /D 4
D 2 /D 5
D 1 /D 6
D 0 /D 7
S D I D a ta C a p tu re
W r ite to S IM D
SPI Master Mode Timing
S C S
S C K (C K P O L B = 1 )
S C K (C K P O L B = 0 )
S D O
S D I D a ta C a p tu re
D 7 /D 0
D 6 /D 1
D 5 /D 2
D 4 /D 3
D 3 /D 4
D 2 /D 5
D 1 /D 6
D 0 /D 7
D 2 /D 5
D 1 /D 6
D 0 /D 7
W r ite to S IM D
( S D O d o e s n o t c h a n g e u n til fir s t S C K e d g e )
SPI Slave Mode Timing - CKEG=0
S C S
S C K (C K P O L B = 1 )
S C K (C K P O L B = 0 )
S D O
S D I D a ta C a p tu re
D 7 /D 0
D 6 /D 1
D 5 /D 2
D 4 /D 3
D 3 /D 4
W r ite to S IM D
( S D O c h a n g e s a s s o o n a s w r itin g o c c u r s ; S D O
is flo a tin g if S C S = 1 )
N o te : F o r S P I s la v e m o d e , if S IM E N = 1 a n d C S E N = 0 , S P I is a lw a y s e n a b le d
a n d ig n o r e s th e S C S le v e l.
SPI Slave Mode Timing - CKEG=1
Rev. 1.40
27
April 19, 2011
HT83F02
b 7
S IM 2 A /B
S IM 1 A /B
b 0
S IM 0 A /B
S IM E N
S IM C 0 A /B
A /B
R e g is te r
N o t im p le m e n te d , r e a d a s " 0 "
S P I O n /O ff c o n tro l
1 : e n a b le
0 : d is a b le
N o t im p le m e n te d
S P I M a s te
S IM 2 A /B
0
0
0
0
1
1
1
1
r /S la v e a n d C lo c k C o n tr o l
S IM 1 A /B
S IM 0 A /B
0
m a s te r, fS Y S /4
0
1
m a s te r, fS Y S /1 6
0
0
m a s te r, fS Y S /6 4
1
1
m a s te r, fS Y S
1
0
re s e rv e d
0
1
s la v e
0
0
re s e rv e d
1
1
re s e rv e d
1
SPI Control Register - SIMC0A/B
b 7
C K P O L A /B
C K E G
A /B
b 0
M L S A /B C S E N A /B W C O L A /B T R F A /B
S IM C 2 A /B R e g is te r
T r a n s m it/R e c e iv e c o m p le te fla g
1 : d a ta tr a n s fe r c o m p le te
0 : d a ta tr a n s fe r in c o m p le te
W r ite c o llis io n fla g
1 : d a ta c o llis io n
0 : n o c o llis io n
S C S A /B p in e n a b le
1 : e n a b le
0 : d is a b le , S C S A /B flo a tin g
D a ta s h ift o r d e r
1 : M S B fir s t
0 : L S B fir s t
S P I c lo c k e d g e s e le c tio n
1 : fa llin g e d g e
0 : r is in g e d g e
S P I c lo c k p o la r ity s e le c tio n
1 : lo w le v e l
0 : h ig h le v e l
N o t im p le m e n te d , r e a d a s " 0 "
SPI Control Register - SIMC2A/B
Rev. 1.40
28
April 19, 2011
HT83F02
A
S P I tra n s fe r
m a s te r
m a s te r o r
s la v e
S IM [2 :0 ]= 0 0 0 ,
0 0 1 ,0 1 0 ,0 1 1
W r ite D a ta
in to S IM D R
C le a r W C O L
s la v e
Y
W C O L = 1 ?
S IM [2 :0 ]= 1 0 1
N
c o n fig u r e
C S E N a n d M L S
T r a n s m is s io n
c o m p le te d ?
(T R F = 1 ? )
Y
R e a d D a ta
fro m S IM D R
S IM E N = 1
C le a r T R F
A
T ra n s fe r
F in is h e d ?
N
Y
E N D
SPI Transfer Control Flowchart
Rev. 1.40
29
April 19, 2011
HT83F02
I2C Interface
The SIMDRA/B register is used to store the data being
transmitted and received on the I2C bus. Before the
microcontroller writes data to the I2C bus, the actual
data to be transmitted must be placed in the
SIMDRA/B register. After the data is received from the
I2C bus, the microcontroller can read it from the
SIMDRA/B register. Any transmission of data to the
I2C bus or reception of data from the I2C bus must be
made via the SIMDRA/B register.
The SIMARA/B register is the location where the slave
address of the microcontroller is stored. Bits 1~7 of
the SIMARA/B register define the microcontroller
slave address. Bit 0 is not defined. When a master device, which is connected to the I2C bus, sends out an
address, which matches the slave address in the
SIMARA/B register, the microcontroller slave device
will be selected.
Note that the SIMARA/B register is the same register
as SIMC2A/B which is used by the SPI interface.
The SIMC0A/B register is used for the I2C overall
on/off control.
2
The I C bus is a bidirectional 2-line communication interface originally developed by Philips. The possibility of
transmitting and receiving data on only 2 lines offers
many new application possibilities for microcontroller
based applications.
· I2C Interface Operation
As the I2C interface pins are pin-shared with segment
pins and with the SPI function pins, the I2C interface
must first be enabled by selecting the correct configuration option.
There are two lines associated with the I2C bus, the
first is known as SDA and is the Serial Data line, the
second is known as SCL line and is the Serial Clock
line. As many devices may be connected together on
the same bus, their outputs are both open drain types.
For this reason it is necessary that external pull-high
resistors are connected to these outputs. Note that no
chip select line exists, as each device on the I2C bus is
identified by a unique address which will be transmitted and received on the I2C bus.
When two devices communicate with each other on
the bidirectional I2C bus, one is known as the master
device and one as the slave device. Both master and
slave can transmit and receive data, however, it is the
master device that has overall control of the bus. For
this device, which only operates in slave mode, there
are two methods of transferring data on the I2C bus,
the slave transmit mode and the slave receive mode.
· I2C Configuration Option
There are several configuration options associated
with the I2C interface. One of these is to enable the
RNICA/B bit function which selects the RNICA/B bit in
SIMC1A/B register. Another configuration option determines the debounce time of the I2C interface. This
add a debounce delay time to the external clock to reduce the possibility of glitches on the clock line causing erroneous operation. The debounce time if
selected can be chosen to be either 1 or 2 system
clocks.
· I2C Registers
There are three control registers associated with the
I2C bus, SIMC0A/B, SIMC1A/B and SIMARA/B and
one data register, SIMDRA/B.
b 7
S A 6 A /B
S A 5 A /B
S A 4 A /B
S A 3 A /B
S A 2 A /B
S A 1 A /B
S A 0 A /B
b 0
S IM A R A /B
R e g is te r
N o t im p le m e n te d , r e a d a s " 0 "
I2C
d e v ic e s la v e a d d r e s s
Slave Address Register - SIMARA/B
b 7
S IM 2 A /B
S IM 1 A /B
S IM 0 A /B
S IM E N A /B
b 0
S IM C 0 A /B
R e g is te r
N o t im p le m e n te d , r e a d a s " 0 "
I2C O n /O ff c o n tro l
1 : e n a b le
0 : d is a b le
N o t im p le m e n te d
I2C M a s te
S IM 2 A /B
0
0
0
0
1
1
1
1
r /S la v e a n d c lo c k
S IM 1 A /B
S IM
0
0
N o
1
0
N o
0
1
N o
1
1
N o
0
0
N o
1
0
N o
0
1
I2C
1
1
N o
c o n
0 A
t u s
t u s
t u s
t u s
t u s
t u s
m o
t u s
tro l
/B
e d
e d
e d
e d
e d
e d
d e
e d
I2C Control Register - SIMC0A/B
Rev. 1.40
30
April 19, 2011
HT83F02
b 7
H C F A /B
H A A S A /B
H B B A /B
H T X A /B
T X A K A /B
b 0
S R W A /B R N IC A /B R X A K A /B
S IM C 1 A /B
R e g is te r
R e c e iv e a c k n o w le d g e fla g
1 : n o t a c k n o w le d g e d
0 : a c k n o w le d g e d
I2 C r u n in g c lo c k
1 : I2 C r u n in g is n o t u s in g in te r n a l c lo c k
0 : I2 C r u n in g is u s in g in te r n a l c lo c k
M a s te r d a ta r e a d /w r ite r e q u e s t fla g
1 : re q u e s t d a ta re a d
0 : r e q u e s t d a ta w r ite
T r a n s m it a c k n o w le d g e fla g
1 : d o n 't a c k n o w le d g e
0 : a c k n o w le d g e
T r a n s m it/R e c e iv e m o d e
1 : tr a n s m it m o d e
0 : r e c e iv e m o d e
I2 C b u s b u s fla g
1 : b u s y
0 : n o t b u s y
C a llin g a d d r e s s m a tc h e d fla g
1 : m a tc h e d
0 : n o t m a tc h e d
D a ta tr a n s fe r fla g
1 : tr a n s fe r c o m p le te
0 : tr a n s fe r n o t c o m p le te
I2C Control Register - SIMC1A/B
The following gives further explanation of each bit:
¨
¨
SRWA/B
The SRWA/B bit is the Slave Read/Write bit. This bit
determines whether the master device wishes to
transmit or receive data from the I2C bus. When the
transmitted address and slave address match, that
is when the HAASA/B bit is set high, the device will
check the SRWA/B bit to determine whether it
should be in transmit mode or receive mode. If the
SRWA/B bit is high, the master is requesting to read
data from the bus, so the device should be in transmit mode. When the SRWA/B bit is zero, the master
will write data to the bus, therefore the device
should be in receive mode to read this data.
¨
RNICA/B
The RNICA/B bit is used as I2C running clock from
Internal or external clock. If this bit is low then I2C
running using internal clock and it will not wake-up
when I2C interrupts in the Power Down Mode. If the
bit is high I2C running using external clock and it will
wake-up when I2C interrupts in the Power Down
Mode.
¨
RXAKA/B
The RXAKA/B flag is the receive acknowledge flag.
When the RXAKA/B bit has been reset to zero it
means that a correct acknowledge signal has been
received at the 9th clock, after 8 bits of data have
been transmitted. When in the transmit mode, the
transmitter checks the RXAKA/B bit to determine if
the receiver wishes to receive the next byte. The
transmitter will therefore continue sending out data
until the RXAKA/B bit is set to ²1². When this occurs, the transmitter will release the SDAA/B line to
allow the master to send a STOP signal to release
the bus.
SIMENA/B
The SIMENA/B bit determines if the I2C bus is enabled or disabled. If data is to be transferred or received on the I2C bus then this bit must be set high.
The following gives further explanation of each bit:
¨
HCFA/B
The HCFA/B flag is the data transfer flag. This flag
will be zero when data is being transferred. Upon
completion of an 8-bit data transfer the flag will go
high and an interrupt will be generated.
¨
HASSA/B
The HASSA/B flag is the address match flag. This
flag is used to determine if the slave device address
is the same as the master transmit address. If the
addresses match then this bit will be high, if there is
no match then the flag will be low.
¨
HBBA/B
The HBBA/B flag is the I2C busy flag. This flag will
be high when the I2C bus is busy which will occur
when a START signal is detected. The flag will be
reset to zero when the bus is free which will occur
when a STOP signal is detected.
¨
HTXA/B
The HTXA/B flag is the transmit/receive mode bit.
This flag should be set high to set the transmit mode
and low for the receive mode.
¨
TXAKA/B
The TXAKA/B flag is the transmit acknowledge flag.
After the receipt of 8-bits of data, this bit will be
transmitted to the bus on the 9th clock. To continue
receiving more data, this bit has to be reset to zero
before further data is received.
Rev. 1.40
31
April 19, 2011
HT83F02
S T A R T s ig n a l
fro m M a s te r
S e n d s la v e a d d r e s s
a n d R /W b it fr o m M a s te r
A c k n o w le d g e
fr o m s la v e
S e n d d a ta b y te
fro m M a s te r
A c k n o w le d g e
fr o m s la v e
S T O P s ig n a l
fro m M a s te r
I2C Bus Communication
· Start Signal
The START signal can only be generated by the master device connected to the I2C bus and not by the
microcontroller, which is only a slave device. This
START signal will be detected by all devices connected to the I2C bus. When detected, this indicates
that the I2C bus is busy and therefore the HBB bit will
be set. A START condition occurs when a high to low
transition on the SDA line takes place when the SCL
line remains high.
2
Communication on the I C bus requires four separate
steps, a START signal, a slave device address transmission, a data transmission and finally a STOP signal.
When a START signal is placed on the I2C bus, all devices on the bus will receive this signal and be notified of
the imminent arrival of data on the bus. The first seven
bits of the data will be the slave address with the first bit
being the MSB. If the address of the microcontroller
matches that of the transmitted address, the HAAS bit in
the SIMC1 register will be set and an I2C interrupt will be
generated. After entering the interrupt service routine,
the microcontroller slave device must first check the
condition of the HAAS bit to determine whether the interrupt source originates from an address match or from
the completion of an 8-bit data transfer. During a data
transfer, note that after the 7-bit slave address has been
transmitted, the following bit, which is the 8th bit, is the
read/write bit whose value will be placed in the SRW bit.
This bit will be checked by the microcontroller to determine whether to go into transmit or receive mode. Before any transfer of data to or from the I2C bus, the
microcontroller must initialise the bus, the following are
steps to achieve this:
· Slave Address
The transmission of a START signal by the master will
be detected by all devices on the I2C bus. To determine which slave device the master wishes to communicate with, the address of the slave device will be
sent out immediately following the START signal. All
slave devices, after receiving this 7-bit address data,
will compare it with their own 7-bit slave address. If the
address sent out by the master matches the internal
address of the microcontroller slave device, then an
internal I2C bus interrupt signal will be generated. The
next bit following the address, which is the 8th bit, defines the read/write status and will be saved to the
SRW bit of the SIMC1 register. The device will then
transmit an acknowledge bit, which is a low level, as
the 9th bit. The microcontroller slave device will also
set the status flag HAAS when the addresses match.
As an I2C bus interrupt can come from two sources,
when the program enters the interrupt subroutine, the
HAAS bit should be examined to see whether the interrupt source has come from a matching slave address or from the completion of a data byte transfer.
When a slave address is matched, the device must be
placed in either the transmit mode and then write data
to the SIMDR register, or in the receive mode where it
must implement a dummy read from the SIMDR register to release the SCL line.
Step 1
Write the slave address of the microcontroller to the I2C
bus address register SIMAR.
Step 2
Set the SIMEN bit in the SIMC0 register to ²1² to enable
the I2C bus.
Step 3
Set the EHI bit of the interrupt control register to enable
the I2C bus interrupt.
Rev. 1.40
32
April 19, 2011
HT83F02
S C L
S ta rt
S R W
S la v e A d d r e s s
0
1
S D A
1
1
0
1
0
1
D a ta
S C L
1
0
0
1
A C K
0
A C K
0
1
0
S to p
0
S D A
S = S
S A =
S R =
M = S
D = D
A = A
P = S
S
ta rt (1
S la v e
S R W
la v e d
a ta (8
C K (R
to p (1
S A
b it)
A d d r e s s ( 7 b its )
b it ( 1 b it)
e v ic e s e n d a c k n o w le d g e b it ( 1 b it)
b its )
X A K b it fo r tr a n s m itte r , T X A K b it fo r r e c e iv e r 1 b it)
b it)
S R
M
D
A
D
A
S
S A
S R
M
D
A
D
A
P
2
I C Communication Timing Diagram
· SRW Bit
the MSB first and the LSB last. After receipt of 8-bits of
data, the receiver must transmit an acknowledge signal, level ²0², before it can receive the next data byte.
If the transmitter does not receive an acknowledge bit
signal from the receiver, then it will release the SDA
line and the master will send out a STOP signal to release control of the I2C bus. The corresponding data
will be stored in the SIMDR register. If setup as a
transmitter, the microcontroller slave device must first
write the data to be transmitted into the SIMDR register. If setup as a receiver, the microcontroller slave device must read the transmitted data from the SIMDR
register.
The SRW bit in the SIMC1 register defines whether
the microcontroller slave device wishes to read data
from the I2C bus or write data to the I2C bus. The
microcontroller should examine this bit to determine if
it is to be a transmitter or a receiver. If the SRW bit is
set to ²1² then this indicates that the master wishes to
read d a t a f r o m t h e I 2 C b u s , t h e r e f o r e t h e
microcontroller slave device must be setup to send
data to the I2C bus as a transmitter. If the SRW bit is
²0² then this indicates that the master wishes to send
data to the I2C bus, therefore the microcontroller slave
device must be setup to read data from the I2C bus as
a receiver.
S C L
· Acknowledge Bit
S D A
After the master has transmitted a calling address,
any slave device on the I2C bus, whose own internal
address matches the calling address, must generate
an acknowledge signal. This acknowledge signal will
inform the master that a slave device has accepted its
calling address. If no acknowledge signal is received
by the master then a STOP signal must be transmitted
by the master to end the communication. When the
HAAS bit is high, the addresses have matched and
the microcontroller slave device must check the SRW
bit to determine if it is to be a transmitter or a receiver.
If the SRW bit is high, the microcontroller slave device
should be setup to be a transmitter so the HTX bit in
the SIMC1 register should be set to ²1² if the SRW bit
is low then the microcontroller slave device should be
setup as a receiver and the HTX bit in the SIMC1 register should be set to ²0².
S ta r t b it
D a ta
s ta b le
D a ta
a llo w
c h a n g e
S to p b it
Data Timing Diagram
· Receive Acknowledge Bit
When the receiver wishes to continue to receive the
next data byte, it must generate an acknowledge bit,
known as TXAK, on the 9th clock. The microcontroller
slave device, which is setup as a transmitter will check
the RXAK bit in the SIMC1 register to determine if it is
to send another data byte, if not then it will release the
SDA line and await the receipt of a STOP signal from
the master.
· Data Byte
The transmitted data is 8-bits wide and is transmitted
after the slave device has acknowledged receipt of its
slave address. The order of serial bit transmission is
Rev. 1.40
33
April 19, 2011
HT83F02
S ta rt
N o
N o
Y e s
H A A S = 1
?
Y e s
Y e s
H T X = 1
?
S R W = 1
?
N o
R e a d fro m
S IM D R
S E T H T X
C L R H T X
C L R T X A K
R E T I
W r ite to
S IM D R
D u m m y R e a d
F ro m S IM D R
R E T I
R E T I
Y e s
R X A K = 1
?
N o
C L R H T X
C L R T X A K
W r ite to
S IM D R
D u m m y R e a d
fro m S IM D R
R E T I
R E T I
I2C Bus ISR Flow Chart
S ta rt
W r ite S la v e
A d d re s s to S IM A R
S E T S IM [2 :0 ]= 1 1 0
S E T S IM E N
D is a b le
I2C B u s
In te rru p t= ?
E n a b le
C L R E S IM I
P o ll S IM F to d e c id e
w h e n to g o to I2C B u s IS R
S E T E S IM I
W a it fo r In te r r u p t
G o to M a in P r o g r a m
G o to M a in P r o g r a m
I2C Bus Initialisation Flow Chart
Rev. 1.40
34
April 19, 2011
HT83F02
Interrupts
rupt vector. The microcontroller will then fetch its next
instruction from this interrupt vector. The instruction at
this vector will usually be a JMP statement which will
take program execution to another section of program
which is known as the interrupt service routine. Here is
located the code to control the appropriate interrupt. The
interrupt service routine must be terminated with a RETI
statement, which retrieves the original Program Counter
address from the stack and allows the microcontroller to
continue with normal execution at the point where the interrupt occurred.
Interrupts are an important part of any microcontroller
system. When an internal function such as a Time Base
or Timer requires microcontroller attention, their corresponding interrupt will enforce a temporary suspension
of the main program allowing the microcontroller to direct attention to their respective needs. Each device
contains a Time Base interrupt and two internal timer interrupt functions. The Time Base interrupt is controlled
by bit 1 of INTC register, while the internal interrupt is
controlled by the Timer Counter overflow.
Interrupt Register
The various interrupt enable bits, together with their associated request flags, are shown in the accompanying
diagram with their order of priority.
Overall interrupt control, which means interrupt enabling
and flag setting, is controlled using two registers, known
as INTC and INTCH, which are located in the Data
Memory. By controlling the appropriate enable bits in
these registers each individual interrupt can be enabled
or disabled. Also when an interrupt occurs, the corresponding request flag will be set by the microcontroller.
The global enable flag if cleared to zero will disable all
interrupts.
Once an interrupt subroutine is serviced, all the other interrupts will be blocked, as the EMI bit will be cleared automatically. This will prevent any further interrupt nesting
from occurring. However, if other interrupt requests occur during this interval, although the interrupt will not be
immediately serviced, the request flag will still be recorded. If an interrupt requires immediate servicing
while the program is already in another interrupt service
routine, the EMI bit should be set after entering the routine, to allow interrupt nesting. If the stack is full, the interrupt request will not be acknowledged, even if the
related interrupt is enabled, until the Stack Pointer is
decremented. If immediate service is desired, the stack
must be prevented from becoming full.
Interrupt Operation
A timer or Time Base overflow or by setting their corresponding request flag, if their appropriate interrupt enable bit is set. When this happens, the Program
Counter, which stores the address of the next instruction
to be executed, will be transferred onto the stack. The
Program Counter will then be loaded with a new address which will be the value of the corresponding interb 7
T 1 F
T 0 F
T B F
E T 1 I
E T 0 I E T B I
b 0
E M I
IN T C R e g is te r
M a s te r In te r r u p t G lo b a l E n a b le
1 : g lo b a l e n a b le
0 : g lo b a l d is a b le
T im e B a s e In te r r u p t E n a b le
1 : e n a b le
0 : d is a b le
T im e r 0 In te r r u p t E n a b le
1 : e n a b le
0 : d is a b le
T im e r 1 In te r r u p t E n a b le
1 : e n a b le
0 : d is a b le
T im e B a s e In te r r u p t R e q u e s t F la g
1 : a c tiv e
0 : in a c tiv e
T im e r 0 In te r r u p t R e q u e s t F la g
1 : a c tiv e
0 : in a c tiv e
T im e r 1 In te r r u p t R e q u e s t F la g
1 : a c tiv e
0 : in a c tiv e
N o im p le m e n te d , r e a d a s " 0 "
Interrupt Control Register
Rev. 1.40
35
April 19, 2011
HT83F02
b 7
S IB F
b 0
E S IB I E S IA I IN T C H
S IA F
R e g is te r
C o n tr o l s e r ia l in te r fa c e A in te r r u p t
1 : e n a b le
0 : d is a b le
C o n tr o l s e r ia l in te r fa c e B in te r r u p t
1 : e n a b le
0 : d is a b le
N o im p le m e n te d , r e a d a s " 0 "
S e r ia l in te r fa c e in te r r u p t A r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
S e r ia l in te r fa c e in te r r u p t B r e q u e s t fla g
1 : a c tiv e
0 : in a c tiv e
N o im p le m e n te d , r e a d a s " 0 "
INTCH Register
A u to m a tic a lly C le a r e d b y IS R
M a n u a lly S e t o r C le a r e d b y S o ftw a r e
A u to m a tic a lly D is a b le d b y IS R
C a n b e E n a b le d M a n u a lly
T im e B a s e
R e q u e s t F la g E IF
E E I
T im e r 0
In te r r u p t R e q u e s t F la g T 0 F
E T 0
T im e r 1
In te r r u p t R e q u e s t F la g T 1 F
E T 1
S IM A
In te r r u p t R e q u e s t F la g S IA F
E S IA I
S IM B
In te r r u p t R e q u e s t F la g S IB F
E S IB I
P r io r ity
E M I
H ig h
In te rru p t
P o llin g
L o w
Interrupt Structure
Interrupt Priority
Time Base Interrupt
Interrupts, occurring in the interval between the rising
edges of two consecutive T2 pulses, will be serviced on
the latter of the two T2 pulses, if the corresponding interrupts are enabled. In case of simultaneous requests, the
accompanying table shows the priority that is applied.
Each device contains a Time Base whose corresponding interrupt enable bits are known as ETBI and is located in the INTC register. For a Time Base generated
interrupt to occur, the corresponding Time Base interrupt enable bit must be first set. Time Base also has a
corresponding Time Base interrupt request flag, which
is known as TBF, also located in the INTC register.
When the master interrupt and corresponding timer interrupt enable bits are enabled, the stack is not full, and
when the corresponding timer overflows a subroutine
call to the corresponding Time Base interrupt vector will
occur. The corresponding Program Memory vector locations for the Time Base is 04H. After entering the interrupt execution routine, the corresponding interrupt
request flag, TBF will be reset and the EMI bit will be
cleared to disable other interrupts.
Interrupt
Vector
HT83F02
Priority
Time Base Interrupt
04H
1
Timer 0 Overflow
08H
2
Timer 1 Overflow
0CH
3
SIM A Interrupt
10H
4
SIM B Interrupt
14H
5
Interrupt Source
Suitable masking of the individual interrupts using the
INTC and INTCH registers can prevent simultaneous
occurrences.
Rev. 1.40
36
April 19, 2011
HT83F02
For an I2C interrupt to occur, the corresponding interrupt
enable bit ESIIA/B must be first set. An actual I2C interrupt will be initialized when the SIMA/B interrupt request
flag, SIFA/B, is set, a situation that will occur when a
matching I2C slave address is received or from the completion of an I2C data byte transfer. When the interrupt is
enabled, the stack is not full and a SIMA/B interrupt occurs, a subroutine call to the SIMA/B interrupt vector at
location 14H, will take place When an I2C interrupt occurs, the interrupt request flag SIFA/B will be reset and
the EMI bit will be cleared to disable other interrupts.
Timer Interrupt
For a timer generated interrupt to occur, the corresponding timer interrupt enable bit must be first set. Each device contains two 8-bit timers whose corresponding
interrupt enable bits are known as ET0 and ET1and are
located in the INTC register. Each timer also has a corresponding timer interrupt request flag, which are
known as T0F and T1F, also located in the INTC register. When the master interrupt and corresponding timer
interrupt enable bits are enabled, the stack is not full,
and when the corresponding timer overflows a subroutine call to the corresponding timer interrupt vector will
occur. The corresponding Program Memory vector locations for Timer 0 and Timer1 are 08H and 0CH. After entering the interrupt execution routine, the corresponding
interrupt request flags, T0F or T1F will be reset and the
EMI bit will be cleared to disable other interrupts.
Programming Considerations
By disabling the interrupt enable bits, a requested interrupt can be prevented from being serviced, however,
once an interrupt request flag is set, it will remain in this
condition in the INTC or INTCH register until the corresponding interrupt is serviced or until the request flag is
cleared by a software instruction.
Serial Interface Module - SIM - Interrupt
SIMA/B Interrupts include both the SPI and I2C Interrupts. The SIMA/B Mode is determined by the SIM2A/B,
SIM1A/B and SIM0A/B bits in the SIMC0A/B register.
It is recommended that programs do not use the ²CALL
subroutine² instruction within the interrupt subroutine.
Interrupts often occur in an unpredictable manner or
need to be serviced immediately in some applications. If
only one stack is left and the interrupt is not well controlled, the original control sequence will be damaged
once a ²CALL subroutine² is executed in the interrupt
subroutine.
For a SPI Interrupt to occur, the global interrupt enable
bit, EMI, and the corresponding SIMA/B interrupt enable
bit, ESII, must be first set. The SIMENA/B bit in the
SIMC0A/B register must also be set. An actual SPI Interrupt will take place when the flag, SIFA/B, is set, a situation that will occur when 8-bits of data are transferred
or received from either of the SPI interfaces. When the
interrupt is enabled, the stack is not full and an SIMA/B
interrupt occurs, a subroutine call to the SIMA/B interrupt vector at location 10H, will take place. When the interrupt is serviced, the SPIA/B interrupt request flag,
SIFA/B, will be automatically reset and the EMI bit will be
automatically cleared to disable other interrupts.
Rev. 1.40
All of these interrupts have the capability of waking up
the processor when in the Power Down Mode. Only the
Program Counter is pushed onto the stack. If the contents of the register or status register are altered by the
interrupt service program, which may corrupt the desired control sequence, then the contents should be
saved in advance.
37
April 19, 2011
HT83F02
Reset and Initialisation
A reset function is a fundamental part of any
microcontroller ensuring that the device can be set to
some predetermined condition irrespective of outside
parameters. The most important reset condition is after
power is first applied to the microcontroller. In this case,
internal circuitry will ensure that the microcontroller, after a short delay, will be in a well defined state and ready
to execute the first program instruction. After this
power-on reset, certain important internal registers will
be set to defined states before the program commences. One of these registers is the Program Counter,
which will be reset to zero forcing the microcontroller to
begin program execution from the lowest Program
Memory address.
V D D
tR
S S T T im e - o u t
D D
S T D
In te rn a l R e s e t
Power-On Reset Timing Chart
For most applications a resistor connected between
VDD and the RES pin and a capacitor connected between VSS and the RES pin will provide a suitable external reset circuit. Any wiring connected to the RES
pin should be kept as short as possible to minimise
any stray noise interference.
In addition to the power-on reset, situations may arise
where it is necessary to forcefully apply a reset condition
when the microcontroller is running. One example of this
is where after power has been applied and the
microcontroller is already running, the RES line is forcefully pulled low. In such a case, known as a normal operation reset, some of the microcontroller registers remain
unchanged allowing the microcontroller to proceed with
normal operation after the reset line is allowed to return
high. Another type of reset is when the Watchdog Timer
overflows and resets the microcontroller. All types of reset operations result in different register conditions being setup.
V D D
1 0 0 k W
R E S
0 .1 m F
V S S
Basic Reset Circuit
For applications that operate within an environment
where more noise is present the Enhanced Reset Circuit shown is recommended.
0 .0 1 m F
1 0 0 k W
Reset Functions
0 .1 m F
· Power-on Reset
V D D
R E S
1 0 k W
There are five ways in which a microcontroller reset can
occur, through events occurring both internally and externally:
V S S
Enhanced Reset Circuit
The most fundamental and unavoidable reset is the
one that occurs after power is first applied to the
microcontroller. As well as ensuring that the Program
Memory begins execution from the first memory address, a power-on reset also ensures that certain
other registers are preset to known conditions. All the
I/O port and port control registers will power up in a
high condition ensuring that all pins will be first set to
inputs.
Although the microcontroller has an internal RC reset
function, if the VDD power supply rise time is not fast
enough or does not stabilise quickly at power-on, the
internal reset function may be incapable of providing
proper reset operation. For this reason it is recommended that an external RC network is connected to
the RES pin, whose additional time delay will ensure
that the RES pin remains low for an extended period
to allow the power supply to stabilise. During this time
delay, normal operation of the microcontroller will be
inhibited. After the RES line reaches a certain voltage
value, the reset delay time tRSTD is invoked to provide
an extra delay time after which the microcontroller will
begin normal operation. The abbreviation SST in the
figures stands for System Start-up Timer.
Rev. 1.40
0 .9 V
R E S
More information regarding external reset circuits is
located in Application Note HA0075E on the Holtek
website.
· RES Pin Reset
This type of reset occurs when the microcontroller is
already running and the RES pin is forcefully pulled
low by external hardware such as an external switch.
In this case as in the case of other reset, the Program
Counter will reset to zero and program execution initiated from this point.
R E S
S S T T im e - o u t
0 .4 V
D D
0 .9 V
tR
D D
S T D
In te rn a l R e s e t
RES Reset Timing Chart
38
April 19, 2011
HT83F02
· Watchdog Time-out Reset during Normal Operation
The following table indicates the way in which the various components of the microcontroller are affected after
a power-on reset occurs.
The Watchdog time-out Reset during normal operation is the same as a hardware RES pin reset except
that the Watchdog time-out flag TO will be set to ²1².
Item
W D T T im e - o u t
tR
S S T T im e - o u t
S T D
In te rn a l R e s e t
WDT Time-out Reset during Normal Operation
Timing Chart
Program Counter
Reset to zero
Interrupts
All interrupts will be disabled
WDT
Clear after reset, WDT begins
counting
Timer
All Timer will be turned off
Prescaler
The Timer Prescaler will be
cleared
Input/Output Ports
I/O ports will be setup as inputs
Stack Pointer
Stack Pointer will point to the top
of the stack
· Watchdog Time-out Reset during Power Down
The Watchdog time-out Reset during Power Down is
a little different from other kinds of reset. Most of the
conditions remain unchanged except that the Program Counter and the Stack Pointer will be cleared to
²0² and the TO flag will be set to ²1². Refer to the A.C.
Characteristics for tSST details.
W D T T im e - o u t
tS
S S T T im e - o u t
Condition After RESET
S T
WDT Time-out Reset during Power Down
Timing Chart
Reset Initial Conditions
The different types of reset described affect the reset
flags in different ways. These flags, known as PDF and
TO are located in the status register and are controlled
by various microcontroller operations, such as the
Power Down function or Watchdog Timer. The reset
flags are shown in the table:
TO PDF
RESET Conditions
0
0
RES reset during power-on
u
u
RES or LVR reset during normal operation
1
u
WDT time-out reset during normal operation
1
1
WDT time-out reset during Power Down
Note: ²u² stands for unchanged
Rev. 1.40
39
April 19, 2011
HT83F02
The different kinds of resets all affect the internal registers of the microcontroller in different ways. To ensure reliable
continuation of normal program execution after a reset occurs, it is important to know what condition the microcontroller
is in after a particular reset occurs. The following table describes how each type of reset affects each of the
microcontroller internal registers. Note that where more than one package type exists the table will reflect the situation
for the larger package type.
Register
Reset
(Power-on)
WDT Time-out
RES Reset
(Normal Operation) (Normal Operation)
RES Reset
(HALT)
WDT Time-out
from HALT
MP0
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
ACC
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
PCL
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
TBLP
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
WDTS
0000 0111
0000 0111
0000 0111
0000 0111
uuuu uuuu
STATUS
--00 xxxx
-- 1u uuuu
--uu uuuu
-- 01 uuuu
--11 uuuu
INTC
-000 0000
-000 0000
-000 0000
-000 0000
-uuu uuuu
TMR0
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
TMR0C
0100 0000
0100 0000
0100 0000
0100 0000
uuuu uuuu
TMR1
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
TMR1C
0100 0000
0100 0000
0100 0000
0100 0000
uuuu uuuu
PA
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PAC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PB
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PBC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PC
---- -111
---- -111
---- -111
---- -111
---- -uuu
PCC
---- -111
---- -111
---- -111
---- -111
---- -uuu
INTCH
--00 --00
--00 --00
--00 --00
--00 --00
--uu --uu
DAL
xxxx ----
uuuu ----
uuuu ----
uuuu ----
uuuu ----
DAH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
PWMC
0--- 0000
0--- 0000
0--- 0000
0--- 0000
u--- uuuu
PWML
xxxx ----
uuuu ----
uuuu ----
uuuu ----
uuuu ----
PWMH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
VOL
xxxx -xxx
uuuu -uuu
uuuu -uuu
uuuu -uuu
uuuu -uuu
SIMC0A
111x xx0-
111x xx0-
111x xx0-
111x xx0-
uuux xxu-
SIMC1A
100x x0x1
100x x0x1
100x x0x1
100x x0x1
uuux xuxu
SIMDRA
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
SIMARA/
SIMC2A
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
SIMC0B
111x xx0-
111x xx0-
111x xx0-
111x xx0-
uuux xxu-
SIMC1B
100x x0x1
100x x0x1
100x x0x1
100x x0x1
uuux xuxu
SIMDRB
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
SIMARB/
SIMC2B
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
PCPHC
---- -000
---- -000
---- -000
---- -000
---- -uuu
Note: ²u² stands for unchanged
²x² stands for unknown
²-² stands for undefined
Rev. 1.40
40
April 19, 2011
HT83F02
Oscillator
open-drain type, a pull high resistor should be connected if it to be used to monitor the internal frequency.
Although this is a cost effective oscillator configuration,
the oscillation frequency can vary with VDD, temperature and process variations and is therefore not suitable
for applications where timing is critical or where accurate oscillator frequencies are required. For the value of
the external resistor ROSC refer to the Holtek website for
typical RC Oscillator vs. Temperature and VDD characteristics graphics. Note that it is the only microcontroller
internal circuitry together with the external resistor, that
determine the frequency of the oscillator. The external
capacitor shown on the diagram does not influence the
frequency of oscillation.
Various oscillator options offer the user a wide range of
functions according to their various application requirements. Three types of system clocks can be selected
while various clock source options for the Watchdog
Timer are provided for maximum flexibility. All oscillator
options are selected through the configuration options.
The three methods of generating the system clock are:
· External crystal/resonator oscillator
· External RC oscillator
· Internal RC oscillator
One of these three methods must be selected using the
configuration options.
More information regarding the oscillator is located in
Application Note HA0075E on the Holtek website.
O S C 1
R
External Crystal/Resonator Oscillator
The simple connection of a crystal across OSC1 and
OSC2 will create the necessary phase shift and feedback for oscillation, and will normally not require external capacitors. However, for some crystals and most
resonator types, to ensure oscillation and accurate frequency generation, it may be necessary to add two
small value external capacitors, C1 and C2. The exact
values of C1 and C2 should be selected in consultation
with the crystal or resonator manufacturer¢s specification. The external parallel feedback resistor, Rp, is normally not required but in some cases may be needed to
assist with oscillation start up.
fS
Ca
Cb
Rf
13~15pF
800kW
O S C 1
R p
C 2
R f
O S C 2
C a
C b
The internal RC oscillator is a fully integrated system oscillator requiring no external components. The internal
RC oscillator has three fixed frequencies of either
4MHz, 8MHz or 12MHz selected by configuration options. Device trimming during the manufacturing process and the inclusion of internal frequency
compensation circuits are used to ensure that the influence of the power supply voltage, temperature and process variations on the oscillation frequency are
minimised. As a result, at a power supply of either 3.3V
or 5V and at a temperature of 25°C degrees, the fixed
oscillation frequency of 4MHz, 8MHz or 12MHz will have
a tolerance within 2%. Note that if this internal system
clock option is selected, as it requires no external pins
for its operation, I/O pins PC1 and PC2 are free for use
as normal I/O pins.
In te r n a l
O s c illa to r
C ir c u it
T o in te r n a l
c ir c u its
N o te : 1 . R p is n o r m a lly n o t r e q u ir e d .
2 . A lth o u g h n o t s h o w n O S C 1 /O S C 2 p in s h a v e a p a r a s itic
c a p a c ita n c e o f a r o u n d 7 p F .
I/O
O S C 1
I/O
O S C 2
Internal RC Oscillator -- HIRC
Crystal/Resonator Oscillator
Watchdog Timer Oscillator
The WDT oscillator is a fully self-contained free running
on-chip RC oscillator with a typical period of 65ms at 5V
requiring no external components. When the device enters the Power Down Mode, the system clock will stop
running but the WDT oscillator continues to free-run and
to keep the watchdog active. However, to preserve
power in certain applications the WDT oscillator can be
disabled via a configuration option.
External RC Oscillator
Using the external system RC oscillator requires that a
resistor, with a value between 150kW and 300kW, is connected between OSC1 and VSS. The generated system
clock divided by 4 will be provided on OSC2 as an output which can be used for external synchronization purposes. Note that as the OSC2 output is an NMOS
Rev. 1.40
O S C 2
Internal RC Oscillator
Oscillator Internal Component Values
C 1
/4 N M O S O p e n D r a in
External RC Oscillator
Internal Ca, Cb, Rf Typical Values @ 5V, 25°C
11~13pF
Y S
O S C
41
April 19, 2011
HT83F02
Power Down Mode and Wake-up
Power Down Mode
Wake-up
All of the Holtek microcontrollers have the ability to enter
a Power Down Mode, also known as the HALT Mode or
Sleep Mode. When the device enters this mode, the normal operating current, will be reduced to an extremely
low standby current level. This occurs because when
the device enters the Power Down Mode, the system
oscillator is stopped which reduces the power consumption to extremely low levels, however, as the device
maintains its present internal condition, it can be woken
up at a later stage and continue running, without requiring a full reset. This feature is extremely important in application areas where the MCU must have its power
supply constantly maintained to keep the device in a
known condition but where the power supply capacity is
limited such as in battery applications.
After the system enters the Power Down Mode, it can be
woken up from one of various sources listed as follows:
· An external reset
· An external falling edge on Port A
· A system interrupt
· A WDT overflow
If the system is woken up by an external reset, the device will experience a full system reset, however, if the
device is woken up by a WDT overflow, a Watchdog
Timer reset will be initiated. Although both of these
wake-up methods will initiate a reset operation, the actual source of the wake-up can be determined by examining the TO and PDF flags. The PDF flag is cleared by a
system power-up or executing the clear Watchdog
Timer instructions and is set when executing the ²HALT²
instruction. The TO flag is set if a WDT time-out occurs,
and causes a wake-up that only resets the Program
Counter and Stack Pointer, the other flags remain in
their original status.
Entering the Power Down Mode
There is only one way for the device to enter the Power
Down Mode and that is to execute the ²HALT² instruction in the application program. When this instruction is
executed, the following will occur:
Each pin on Port A can be setup via an individual configuration option to permit a negative transition on the pin
to wake-up the system. When a Port A pin wake-up occurs, the program will resume execution at the instruction following the ²HALT² instruction.
· The system oscillator will stop running and the appli-
cation program will stop at the ²HALT² instruction.
· The Data Memory contents and registers will maintain
their present condition.
· The WDT will be cleared and resume counting if the
If the system is woken up by an interrupt, then two possible situations may occur. The first is where the related
interrupt is disabled or the interrupt is enabled but the
stack is full, in which case the program will resume execution at the instruction following the ²HALT² instruction.
In this situation, the interrupt which woke-up the device
will not be immediately serviced, but will rather be serviced later when the related interrupt is finally enabled or
when a stack level becomes free. The other situation is
where the related interrupt is enabled and the stack is
not full, in which case the regular interrupt response
takes place. If an interrupt request flag is set to ²1² before entering the Power Down Mode, the wake-up function of the related interrupt will be disabled.
WDT clock source is selected to come from the WDT
oscillator. The WDT will stop if its clock source originates from the system clock.
· The I/O ports will maintain their present condition.
· In the status register, the Power Down flag, PDF, will
be set and the Watchdog time-out flag, TO, will be
cleared.
Standby Current Considerations
As the main reason for entering the Power Down Mode
is to keep the current consumption of the MCU to as low
a value as possible, perhaps only in the order of several
micro-amps, there are other considerations which must
also be taken into account by the circuit designer if the
power consumption is to be minimized. Special attention must be made to the I/O pins on the device. All
high-impedance input pins must be connected to either
a fixed high or low level as any floating input pins could
create internal oscillations and result in increased current consumption. Care must also be taken with the
loads, which are connected to I/Os, which are setup as
outputs. These should be placed in a condition in which
minimum current is drawn or connected only to external
circuits that do not draw current, such as other CMOS
inputs. Also note that additional standby current will also
be required if the configuration options have enabled the
Watchdog Timer internal oscillator.
Rev. 1.40
No matter what the source of the wake-up event is, once
a wake-up situation occurs, a time period equal to 1024
system clock periods will be required before normal system operation resumes. However, if the wake-up has
originated due to an interrupt, the actual interrupt subroutine execution will be delayed by an additional one or
more cycles. If the wake-up results in the execution of
the next instruction following the ²HALT² instruction, this
will be executed immediately after the 1024 system
clock period delay has ended.
42
April 19, 2011
HT83F02
Low Voltage Reset - LVR
system clock divided by 4. Note that if the WDT configuration option has been disabled, then any instruction relating to its operation will result in no operation.
The microcontroller contains a low voltage reset circuit
in order to monitor the supply voltage of the device,
which is selected via a configuration option. If the supply
voltage of the device drops to within a range of
0.9V~VLVR such as might occur when changing the
battery, the LVR will automatically reset the device internally.
The internal WDT oscillator has an approximate period
of 65ms at a supply voltage of 5V. If selected, it is first divided by 256 via an 8-stage counter to give a nominal
period of 17ms. Note that this period can vary with VDD,
temperature and process variations. For longer WDT
time-out periods the WDT prescaler can be utilized. By
writing the required value to bits 0, 1 and 2 of the WDTS
register, known as WS0, WS1 and WS2, longer time-out
periods can be achieved. With WS0, WS1 and WS2 all
equal to 1, the division ratio is 1:128 which gives a maximum time-out period of about 2.1s.
Low Voltage Detector - LVD
This Low Voltage Detect internal function provides a
means for the user to monitor when the power supply
voltage falls below a certain fixed level as specified in
the DC characteristics. Bit 2 of PWMC register and Low
Voltage Detector option are used to control the overall
function of the LVD. Low Voltage Detector option is the
enable/disable control bit, when select disable the overall function of the LVD will be disabled.
A configuration option can select the instruction clock,
which is the system clock divided by 4, as the WDT clock
source instead of the internal WDT oscillator. If the instruction clock is used as the clock source, it must be
noted that when the system enters the Power Down
Mode, as the system clock is stopped, then the WDT
clock source will also be stopped. Therefore the WDT
will lose its protecting purposes. In such cases the system cannot be restarted by the WDT and can only be restarted using external signals. For systems that operate
in noisy environments, using the internal WDT oscillator
is therefore the recommended choice.
Bit 2 is the LVD detector output bit and is known as
LVDF. Under normal operation, and when the power
supply voltage is above the specified VLVD value in the
DC characteristic section, the LVDF bit will remain at a
zero value. If the power supply voltage should fall below
this VLVD value then the LVDF bit will change to a high
value indicating a low voltage condition. Note that the
LVDF bit is a read-only bit. By polling the LVDF bit in the
PWMC register, the application program can therefore
determine the presence of a low voltage condition.
Under normal program operation, a WDT time-out will
initialise a device reset and set the status bit TO. However, if the system is in the Power Down Mode, when a
WDT time-out occurs, only the Program Counter and
Stack Pointer will be reset. Three methods can be
adopted to clear the contents of the WDT and the WDT
prescaler. The first is an external hardware reset, which
means a low level on the RES pin, the second is using
the watchdog software instructions and the third is via a
²HALT² instruction.
Operation
The Low Voltage Detector must first be enabled using a
configuration option.
The LVD control bit is bit 2 of the PWMC regsiter and is
known as LVDF. Under normal operation, and when the
power supply voltage is above the specified VLVD value
in the DC characteristic section, the LVDF bit will remain
at a zero value. If the power supply voltage should fall below this VLVD value then the LVDF bit will change to a
high value indicating a low voltage condition. Note that
the LVDF bit is a read-only bit. By polling the LVDF bit in
the PWMC register, the application program can therefore determine the presence of a low voltage condition.
There are two methods of using software instructions to
clear the Watchdog Timer, one of which must be chosen
by configuration option. The first option is to use the single ²CLR WDT² instruction while the second is to use
the two commands ²CLR WDT1² and ²CLR WDT2². For
the first option, a simple execution of ²CLR WDT² will
clear the WDT while for the second option, both ²CLR
WDT1² and ²CLR WDT2² must both be executed to
successfully clear the WDT. Note that for this second
option, if ²CLR WDT1² is used to clear the WDT, successive executions of this instruction will have no effect,
only the execution of a ²CLR WDT2² instruction will
clear the WDT. Similarly, after the ²CLR WDT2² instruction has been executed, only a successive ²CLR WDT1²
instruction can clear the Watchdog Timer.
Watchdog Timer
The Watchdog Timer is provided to prevent program
malfunctions or sequences from jumping to unknown locations, due to certain uncontrollable external events
such as electrical noise. It operates by providing a device reset when the WDT counter overflows. The WDT
clock is supplied by one of two sources selected by configuration option: its own self-contained dedicated internal WDT oscillator, or the instruction clock which is the
Rev. 1.40
43
April 19, 2011
HT83F02
b 7
W S 2
W S 1
b 0
W S 0
W D T S R e g is te r
W D T p r e s c a le r r a te s e le c t
W D T
W S 0
W S 1
W S 2
1
0
0
0
1
1
0
0
1
0
1
0
1
1
1
0
1
0
0
1
1
1
0
1
1
0
1
1
1
1
1
1
:1
R a te
:2
:4
:8
:1 6
:3 2
:6 4
:1 2 8
N o t u s e d
Watchdog Timer Register
C L R
C L R
W D T 1 F la g
W D T 2 F la g
C le a r W D T T y p e
C o n fig u r a tio n O p tio n
1 o r 2 In s tr u c tio n s
fS
Y S
/4
W D T O s c illa to r
C L R
W D T C lo c k S o u r c e
C o n fig u r a tio n O p tio n
C L R
8 - b it C o u n te r
(¸ 2 5 6 )
7 - b it P r e s c a le r
W D T C lo c k S o u r c e
W S 0 ~ W S 2
8 -to -1 M U X
W D T T im e - o u t
Watchdog Timer
Voice Output
b 7
D 3
The device contains an internal 12-bit DAC function
which can be used for audio signal generation.
D 2
D 1
b 0
D 0
D A L R e g is te r
N o t u s e d , re a d a s "0 "
Voice Control
D A L R e g is te r
Two internal registers DAL and DAH contain the 12-bit
digital value for conversion by the internal DAC. There is
also a DAC enable/disable control bit in the PWMC control register for overall on/off control of the DAC circuit. If
the DAC circuit is not enabled, the DAH/DAL value outputs will be invalid. Writing a ²1² to the DAC bit in bit1 of
PWMC will enable the enable DAC circuit, while writing
a ²0² to the DAC bit will disable the DAC circuit.
b 7
D 1 1
D 1 0
D 9
D 8
D 7
D 6
D A H
b 7
D 5
b 0
D 4
R e g is te r
b 0
V O L 2 V O L 1 V O L 0
A u d io o u tp u t
D A H
R e g is te r
A u d io o u tp u t
V O L R e g is te r
D A C v o lu m e c o n tr o l d a ta
N o t u s e d , re a d a s "0 "
U s e d b y P W M
Audio Output and Volume Control - DAL, DAH, VOL
V o ic e C o n tr o l R e g is te r
The audio output is 12-bits wide whose highest 8-bits
are written into the DAH register and whose lowest four
bits are written into the highest four bits of the DAL register. Bits 0~3 of the DAL register are always read as zero.
There are 8 levels of volume which are setup using the
VOL register. Only the lowest 3-bits of this register are
used for volume control.
o u tp u t
VOL[2:0]
DAC Volume Control
111
High Volume
­
110
101
100
011
010
001
000
Rev. 1.00
44
¯
Low Volume
August 31, 2010
HT83F02
Pulse Width Modulation Output
b 7
P 3
All devices include a single 12-bit PWM function which
can directly drive external audio components such as
speakers.
P 2
P 1
b 0
P 0
P W M L R e g is te r
N o t u s e d , re a d a s "0 "
P W M
P u ls e W id th M o d u la to r D a ta L o w
Pulse Width Modulator Operation
b 7
P 1 1
The PWM output is provided on two complimentary outputs on the PWM1 and PWM2 pins, providing a differential output pair and thus capable of higher drive power.
These two pins can directly drive a piezo buzzer or an 8
ohm speaker without using external components. The
PWM outputs can also be used single ended, where the
signal is provided on the PWM1 output, and again can
also be used by itself alone to drive a piezo buzzer or an 8
ohm speaker without external components. This single
end output drive type is chosen using the SINGLE_PWM
bit in the PWMC register.
P 1 0
P 9
P 8
P 7
P 6
b 0
P 5
P 4
P W M H
P W M
o u tp u t
R e g is te r
R e g is te r
o u tp u t
P u ls e W id th M o d u la to r D a ta H ig h R e g is te r
b 7
V 3
V 2
V 1
b 0
V 0
V O L R e g is te r
U s e d b y a u d io o u tp u t
N o t u s e d , re a d a s "0 "
P W M
V o ic e C o n tr o l R e g is te r
If the MSB_SIGN bit is low, then the signal that is provided on PWM1and PWM2 will obtain a GND level voltage after setting the PWMCC bit high. If the MSB_SIGN
bit is high, then the signal that is provided on PWM2 and
PWM1 will have a GND level voltage when the PWMCC
bit is set high.
v o lu m e c o n tr o l d a ta
V[3:0]
PWM Volume Control
1xxx
High Volume
­
0111
0110
0101
0100
The two PWM outputs will initially be at low levels, and if
the PWM function is stopped will also return to a low
level. If the PWMCC bit changes from low to high then
the PWM function will start running and latch new data.
If the data is not updated then the old value will remain. If
the PWMCC bit changes from high to low, at the end of
the duty cycle, the PWM output will stop.
0011
0010
¯
Low Volume
0001
0000
P W M 1
P W M 2
S p e a k e r
0 .0 1 m F *
0 .0 1 m F *
N o te : " * " F o r r e d u c in g th e d ig ita l n o is e th a t P W M m a y
c a u s e , c a n c o n s id e r in c r e m e n t c a p a c ito r s .
b 7
M S B _ S IG N
S IN G L E _ P W M
L V D F
D A C
b 0
P W M C C
P W M C
R e g is te r
P W M E n a b le
1 : e n a b le
0 : d is a b le
D A C e n a b le
1 : e n a b le
0 : d is a b le
L V D d e te c tio n fla g
1 : L V D d e te c tio n
0 : L V D n o n - d e te c tio n
S in g le P W M O u tp u t
1 : s in g le o u tp u t
0 : d u a l o u tp u ts
N o t im p le m e n te d , r e a d a s " 0 "
P 1 1 P a r a lle l D a ta P o la r ity
1 : P 1 1 n o n - in v e r t
0 : P 1 1 in v e r t
Pulse Width Modulator Control Register
Rev. 1.40
45
April 19, 2011
HT83F02
Configuration Options
Configuration options refer to certain options within the MCU that are programmed into the device during the programming process. During the development process, these options are selected using the HT-IDE software development
tools. As these options are programmed into the device using the hardware programming tools, once they are selected
they cannot be changed later by the application software.
No.
Options
I/O Options
1
PA0~PA7: wake-up enable or disable
2
PA0~PA7: pull-high enable or disable
3
PB0~PB7: pull-high enable or disable
Oscillator Options
4
OSC type selection: ERC, crystal or HIRC
HIRC Options
5
HIRC option: 4MHz, 8MHz, 12MHz
Watchdog Options
6
WDT: enable or disable
7
WDT clock source: WDTOSC or T1
PB I/O Port Output Voltage Options
8
VDD_PBIO/VDD type selection: VDD_PBIO or VDD for Port B, SPI, I2C I/O per bit
LVR Option
9
LVR function: enable or disable
LVD Option
10
LVD function: enable or disable
Reset Options
11
Reset function: PC0 or reset pin
SIMA Options
12
SIMA Function: enable or disable
13
SPIA S/W CSEN: enable or disable
14
SPIA S/W WCOL: enable or disable
15
I2CA RNIC: enable or disable
16
I2CA debounce time: 0/1/2 system clocks
SIMB Options
17
SIMB Function: enable or disable
18
SPIB S/W CSEN: enable or disable
19
SPIB S/W WCOL: enable or disable
20
I2CB RNIC: enable or disable
21
I2CB debounce time: 0/1/2 system clocks
Rev. 1.40
46
April 19, 2011
HT83F02
Application Circuits
VDD=2.4V~5.5V
Rev. 1.40
47
April 19, 2011
HT83F02
Instruction Set
subtract instruction mnemonics to enable the necessary
arithmetic to be carried out. Care must be taken to ensure correct handling of carry and borrow data when results exceed 255 for addition and less than 0 for
subtraction. The increment and decrement instructions
INC, INCA, DEC and DECA provide a simple means of
increasing or decreasing by a value of one of the values
in the destination specified.
Introduction
Central t o t h e s u c c e s s f u l o p e r a t i o n o f a n y
microcontroller is its instruction set, which is a set of program instruction codes that directs the microcontroller to
perform certain operations. In the case of Holtek
microcontrollers, a comprehensive and flexible set of
over 60 instructions is provided to enable programmers
to implement their application with the minimum of programming overheads.
Logical and Rotate Operations
For easier understanding of the various instruction
codes, they have been subdivided into several functional groupings.
The standard logical operations such as AND, OR, XOR
and CPL all have their own instruction within the Holtek
microcontroller instruction set. As with the case of most
instructions involving data manipulation, data must pass
through the Accumulator which may involve additional
programming steps. In all logical data operations, the
zero flag may be set if the result of the operation is zero.
Another form of logical data manipulation comes from
the rotate instructions such as RR, RL, RRC and RLC
which provide a simple means of rotating one bit right or
left. Different rotate instructions exist depending on program requirements. Rotate instructions are useful for
serial port programming applications where data can be
rotated from an internal register into the Carry bit from
where it can be examined and the necessary serial bit
set high or low. Another application where rotate data
operations are used is to implement multiplication and
division calculations.
Instruction Timing
Most instructions are implemented within one instruction cycle. The exceptions to this are branch, call, or table read instructions where two instruction cycles are
required. One instruction cycle is equal to 4 system
clock cycles, therefore in the case of an 8MHz system
oscillator, most instructions would be implemented
within 0.5ms and branch or call instructions would be implemented within 1ms. Although instructions which require one more cycle to implement are generally limited
to the JMP, CALL, RET, RETI and table read instructions, it is important to realize that any other instructions
which involve manipulation of the Program Counter Low
register or PCL will also take one more cycle to implement. As instructions which change the contents of the
PCL will imply a direct jump to that new address, one
more cycle will be required. Examples of such instructions would be ²CLR PCL² or ²MOV PCL, A². For the
case of skip instructions, it must be noted that if the result of the comparison involves a skip operation then
this will also take one more cycle, if no skip is involved
then only one cycle is required.
Branches and Control Transfer
Program branching takes the form of either jumps to
specified locations using the JMP instruction or to a subroutine using the CALL instruction. They differ in the
sense that in the case of a subroutine call, the program
must return to the instruction immediately when the subroutine has been carried out. This is done by placing a
return instruction RET in the subroutine which will cause
the program to jump back to the address right after the
CALL instruction. In the case of a JMP instruction, the
program simply jumps to the desired location. There is
no requirement to jump back to the original jumping off
point as in the case of the CALL instruction. One special
and extremely useful set of branch instructions are the
conditional branches. Here a decision is first made regarding the condition of a certain data memory or individual bits. Depending upon the conditions, the program
will continue with the next instruction or skip over it and
jump to the following instruction. These instructions are
the key to decision making and branching within the program perhaps determined by the condition of certain input switches or by the condition of internal data bits.
Moving and Transferring Data
The transfer of data within the microcontroller program
is one of the most frequently used operations. Making
use of three kinds of MOV instructions, data can be
transferred from registers to the Accumulator and
vice-versa as well as being able to move specific immediate data directly into the Accumulator. One of the most
important data transfer applications is to receive data
from the input ports and transfer data to the output ports.
Arithmetic Operations
The ability to perform certain arithmetic operations and
data manipulation is a necessary feature of most
microcontroller applications. Within the Holtek
microcontroller instruction set are a range of add and
Rev. 1.40
48
April 19, 2011
HT83F02
Bit Operations
Other Operations
The ability to provide single bit operations on Data Memory is an extremely flexible feature of all Holtek
microcontrollers. This feature is especially useful for
output port bit programming where individual bits or port
pins can be directly set high or low using either the ²SET
[m].i² or ²CLR [m].i² instructions respectively. The feature removes the need for programmers to first read the
8-bit output port, manipulate the input data to ensure
that other bits are not changed and then output the port
with the correct new data. This read-modify-write process is taken care of automatically when these bit operation instructions are used.
In addition to the above functional instructions, a range
of other instructions also exist such as the ²HALT² instruction for Power-down operations and instructions to
control the operation of the Watchdog Timer for reliable
program operations under extreme electric or electromagnetic environments. For their relevant operations,
refer to the functional related sections.
Instruction Set Summary
The following table depicts a summary of the instruction
set categorised according to function and can be consulted as a basic instruction reference using the following listed conventions.
Table Read Operations
Table conventions:
Data storage is normally implemented by using registers. However, when working with large amounts of
fixed data, the volume involved often makes it inconvenient to store the fixed data in the Data Memory. To overcome this problem, Holtek microcontrollers allow an
area of Program Memory to be setup as a table where
data can be directly stored. A set of easy to use instructions provides the means by which this fixed data can be
referenced and retrieved from the Program Memory.
Mnemonic
x: Bits immediate data
m: Data Memory address
A: Accumulator
i: 0~7 number of bits
addr: Program memory address
Description
Cycles
Flag Affected
1
1Note
1
1
1Note
1
1
1Note
1
1Note
1Note
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
C
1
1
1
1Note
1Note
1Note
1
1
1
1Note
1
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
1
1Note
1
1Note
Z
Z
Z
Z
Arithmetic
ADD A,[m]
ADDM A,[m]
ADD A,x
ADC A,[m]
ADCM A,[m]
SUB A,x
SUB A,[m]
SUBM A,[m]
SBC A,[m]
SBCM A,[m]
DAA [m]
Add Data Memory to ACC
Add ACC to Data Memory
Add immediate data to ACC
Add Data Memory to ACC with Carry
Add ACC to Data memory with Carry
Subtract immediate data from the ACC
Subtract Data Memory from ACC
Subtract Data Memory from ACC with result in Data Memory
Subtract Data Memory from ACC with Carry
Subtract Data Memory from ACC with Carry, result in Data Memory
Decimal adjust ACC for Addition with result in Data Memory
Logic Operation
AND A,[m]
OR A,[m]
XOR A,[m]
ANDM A,[m]
ORM A,[m]
XORM A,[m]
AND A,x
OR A,x
XOR A,x
CPL [m]
CPLA [m]
Logical AND Data Memory to ACC
Logical OR Data Memory to ACC
Logical XOR Data Memory to ACC
Logical AND ACC to Data Memory
Logical OR ACC to Data Memory
Logical XOR ACC to Data Memory
Logical AND immediate Data to ACC
Logical OR immediate Data to ACC
Logical XOR immediate Data to ACC
Complement Data Memory
Complement Data Memory with result in ACC
Increment & Decrement
INCA [m]
INC [m]
DECA [m]
DEC [m]
Rev. 1.40
Increment Data Memory with result in ACC
Increment Data Memory
Decrement Data Memory with result in ACC
Decrement Data Memory
49
April 19, 2011
HT83F02
Mnemonic
Description
Cycles
Flag Affected
Rotate Data Memory right with result in ACC
Rotate Data Memory right
Rotate Data Memory right through Carry with result in ACC
Rotate Data Memory right through Carry
Rotate Data Memory left with result in ACC
Rotate Data Memory left
Rotate Data Memory left through Carry with result in ACC
Rotate Data Memory left through Carry
1
1Note
1
1Note
1
1Note
1
1Note
None
None
C
C
None
None
C
C
Move Data Memory to ACC
Move ACC to Data Memory
Move immediate data to ACC
1
1Note
1
None
None
None
Clear bit of Data Memory
Set bit of Data Memory
1Note
1Note
None
None
Jump unconditionally
Skip if Data Memory is zero
Skip if Data Memory is zero with data movement to ACC
Skip if bit i of Data Memory is zero
Skip if bit i of Data Memory is not zero
Skip if increment Data Memory is zero
Skip if decrement Data Memory is zero
Skip if increment Data Memory is zero with result in ACC
Skip if decrement Data Memory is zero with result in ACC
Subroutine call
Return from subroutine
Return from subroutine and load immediate data to ACC
Return from interrupt
2
1Note
1note
1Note
1Note
1Note
1Note
1Note
1Note
2
2
2
2
None
None
None
None
None
None
None
None
None
None
None
None
None
Read table (current page) to TBLH and Data Memory
Read table (last page) to TBLH and Data Memory
2Note
2Note
None
None
No operation
Clear Data Memory
Set Data Memory
Clear Watchdog Timer
Pre-clear Watchdog Timer
Pre-clear Watchdog Timer
Swap nibbles of Data Memory
Swap nibbles of Data Memory with result in ACC
Enter power down mode
1
1Note
1Note
1
1
1
1Note
1
1
None
None
None
TO, PDF
TO, PDF
TO, PDF
None
None
TO, PDF
Rotate
RRA [m]
RR [m]
RRCA [m]
RRC [m]
RLA [m]
RL [m]
RLCA [m]
RLC [m]
Data Move
MOV A,[m]
MOV [m],A
MOV A,x
Bit Operation
CLR [m].i
SET [m].i
Branch
JMP addr
SZ [m]
SZA [m]
SZ [m].i
SNZ [m].i
SIZ [m]
SDZ [m]
SIZA [m]
SDZA [m]
CALL addr
RET
RET A,x
RETI
Table Read
TABRDC [m]
TABRDL [m]
Miscellaneous
NOP
CLR [m]
SET [m]
CLR WDT
CLR WDT1
CLR WDT2
SWAP [m]
SWAPA [m]
HALT
Note: 1. For skip instructions, if the result of the comparison involves a skip then two cycles are required,
if no skip takes place only one cycle is required.
2. Any instruction which changes the contents of the PCL will also require 2 cycles for execution.
3. For the ²CLR WDT1² and ²CLR WDT2² instructions the TO and PDF flags may be affected by
the execution status. The TO and PDF flags are cleared after both ²CLR WDT1² and
²CLR WDT2² instructions are consecutively executed. Otherwise the TO and PDF flags
remain unchanged.
Rev. 1.40
50
April 19, 2011
HT83F02
Instruction Definition
ADC A,[m]
Add Data Memory to ACC with Carry
Description
The contents of the specified Data Memory, Accumulator and the carry flag are added. The
result is stored in the Accumulator.
Operation
ACC ¬ ACC + [m] + C
Affected flag(s)
OV, Z, AC, C
ADCM A,[m]
Add ACC to Data Memory with Carry
Description
The contents of the specified Data Memory, Accumulator and the carry flag are added. The
result is stored in the specified Data Memory.
Operation
[m] ¬ ACC + [m] + C
Affected flag(s)
OV, Z, AC, C
ADD A,[m]
Add Data Memory to ACC
Description
The contents of the specified Data Memory and the Accumulator are added. The result is
stored in the Accumulator.
Operation
ACC ¬ ACC + [m]
Affected flag(s)
OV, Z, AC, C
ADD A,x
Add immediate data to ACC
Description
The contents of the Accumulator and the specified immediate data are added. The result is
stored in the Accumulator.
Operation
ACC ¬ ACC + x
Affected flag(s)
OV, Z, AC, C
ADDM A,[m]
Add ACC to Data Memory
Description
The contents of the specified Data Memory and the Accumulator are added. The result is
stored in the specified Data Memory.
Operation
[m] ¬ ACC + [m]
Affected flag(s)
OV, Z, AC, C
AND A,[m]
Logical AND Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical AND operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²AND² [m]
Affected flag(s)
Z
AND A,x
Logical AND immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical AND
operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²AND² x
Affected flag(s)
Z
ANDM A,[m]
Logical AND ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical AND operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²AND² [m]
Affected flag(s)
Z
Rev. 1.40
51
April 19, 2011
HT83F02
CALL addr
Subroutine call
Description
Unconditionally calls a subroutine at the specified address. The Program Counter then increments by 1 to obtain the address of the next instruction which is then pushed onto the
stack. The specified address is then loaded and the program continues execution from this
new address. As this instruction requires an additional operation, it is a two cycle instruction.
Operation
Stack ¬ Program Counter + 1
Program Counter ¬ addr
Affected flag(s)
None
CLR [m]
Clear Data Memory
Description
Each bit of the specified Data Memory is cleared to 0.
Operation
[m] ¬ 00H
Affected flag(s)
None
CLR [m].i
Clear bit of Data Memory
Description
Bit i of the specified Data Memory is cleared to 0.
Operation
[m].i ¬ 0
Affected flag(s)
None
CLR WDT
Clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
CLR WDT1
Pre-clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared. Note that this instruction works in conjunction with CLR WDT2 and must be executed alternately with CLR WDT2 to have effect. Repetitively executing this instruction without alternately executing CLR WDT2 will have no
effect.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
CLR WDT2
Pre-clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared. Note that this instruction works in conjunction with CLR WDT1 and must be executed alternately with CLR WDT1 to have effect. Repetitively executing this instruction without alternately executing CLR WDT1 will have no
effect.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
Rev. 1.40
52
April 19, 2011
HT83F02
CPL [m]
Complement Data Memory
Description
Each bit of the specified Data Memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice versa.
Operation
[m] ¬ [m]
Affected flag(s)
Z
CPLA [m]
Complement Data Memory with result in ACC
Description
Each bit of the specified Data Memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice versa. The complemented result
is stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m]
Affected flag(s)
Z
DAA [m]
Decimal-Adjust ACC for addition with result in Data Memory
Description
Convert the contents of the Accumulator value to a BCD ( Binary Coded Decimal) value resulting from the previous addition of two BCD variables. If the low nibble is greater than 9 or
if AC flag is set, then a value of 6 will be added to the low nibble. Otherwise the low nibble
remains unchanged. If the high nibble is greater than 9 or if the C flag is set, then a value of
6 will be added to the high nibble. Essentially, the decimal conversion is performed by adding 00H, 06H, 60H or 66H depending on the Accumulator and flag conditions. Only the C
flag may be affected by this instruction which indicates that if the original BCD sum is
greater than 100, it allows multiple precision decimal addition.
Operation
[m] ¬ ACC + 00H or
[m] ¬ ACC + 06H or
[m] ¬ ACC + 60H or
[m] ¬ ACC + 66H
Affected flag(s)
C
DEC [m]
Decrement Data Memory
Description
Data in the specified Data Memory is decremented by 1.
Operation
[m] ¬ [m] - 1
Affected flag(s)
Z
DECA [m]
Decrement Data Memory with result in ACC
Description
Data in the specified Data Memory is decremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m] - 1
Affected flag(s)
Z
HALT
Enter power down mode
Description
This instruction stops the program execution and turns off the system clock. The contents
of the Data Memory and registers are retained. The WDT and prescaler are cleared. The
power down flag PDF is set and the WDT time-out flag TO is cleared.
Operation
TO ¬ 0
PDF ¬ 1
Affected flag(s)
TO, PDF
Rev. 1.40
53
April 19, 2011
HT83F02
INC [m]
Increment Data Memory
Description
Data in the specified Data Memory is incremented by 1.
Operation
[m] ¬ [m] + 1
Affected flag(s)
Z
INCA [m]
Increment Data Memory with result in ACC
Description
Data in the specified Data Memory is incremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m] + 1
Affected flag(s)
Z
JMP addr
Jump unconditionally
Description
The contents of the Program Counter are replaced with the specified address. Program
execution then continues from this new address. As this requires the insertion of a dummy
instruction while the new address is loaded, it is a two cycle instruction.
Operation
Program Counter ¬ addr
Affected flag(s)
None
MOV A,[m]
Move Data Memory to ACC
Description
The contents of the specified Data Memory are copied to the Accumulator.
Operation
ACC ¬ [m]
Affected flag(s)
None
MOV A,x
Move immediate data to ACC
Description
The immediate data specified is loaded into the Accumulator.
Operation
ACC ¬ x
Affected flag(s)
None
MOV [m],A
Move ACC to Data Memory
Description
The contents of the Accumulator are copied to the specified Data Memory.
Operation
[m] ¬ ACC
Affected flag(s)
None
NOP
No operation
Description
No operation is performed. Execution continues with the next instruction.
Operation
No operation
Affected flag(s)
None
OR A,[m]
Logical OR Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical OR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²OR² [m]
Affected flag(s)
Z
Rev. 1.40
54
April 19, 2011
HT83F02
OR A,x
Logical OR immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical OR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²OR² x
Affected flag(s)
Z
ORM A,[m]
Logical OR ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical OR operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²OR² [m]
Affected flag(s)
Z
RET
Return from subroutine
Description
The Program Counter is restored from the stack. Program execution continues at the restored address.
Operation
Program Counter ¬ Stack
Affected flag(s)
None
RET A,x
Return from subroutine and load immediate data to ACC
Description
The Program Counter is restored from the stack and the Accumulator loaded with the
specified immediate data. Program execution continues at the restored address.
Operation
Program Counter ¬ Stack
ACC ¬ x
Affected flag(s)
None
RETI
Return from interrupt
Description
The Program Counter is restored from the stack and the interrupts are re-enabled by setting the EMI bit. EMI is the master interrupt global enable bit. If an interrupt was pending
when the RETI instruction is executed, the pending Interrupt routine will be processed before returning to the main program.
Operation
Program Counter ¬ Stack
EMI ¬ 1
Affected flag(s)
None
RL [m]
Rotate Data Memory left
Description
The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit
0.
Operation
[m].(i+1) ¬ [m].i; (i = 0~6)
[m].0 ¬ [m].7
Affected flag(s)
None
RLA [m]
Rotate Data Memory left with result in ACC
Description
The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit
0. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; (i = 0~6)
ACC.0 ¬ [m].7
Affected flag(s)
None
Rev. 1.40
55
April 19, 2011
HT83F02
RLC [m]
Rotate Data Memory left through Carry
Description
The contents of the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7
replaces the Carry bit and the original carry flag is rotated into bit 0.
Operation
[m].(i+1) ¬ [m].i; (i = 0~6)
[m].0 ¬ C
C ¬ [m].7
Affected flag(s)
C
RLCA [m]
Rotate Data Memory left through Carry with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7 replaces
the Carry bit and the original carry flag is rotated into the bit 0. The rotated result is stored in
the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; (i = 0~6)
ACC.0 ¬ C
C ¬ [m].7
Affected flag(s)
C
RR [m]
Rotate Data Memory right
Description
The contents of the specified Data Memory are rotated right by 1 bit with bit 0 rotated into
bit 7.
Operation
[m].i ¬ [m].(i+1); (i = 0~6)
[m].7 ¬ [m].0
Affected flag(s)
None
RRA [m]
Rotate Data Memory right with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated right by 1 bit with bit 0 rotated into bit 7. The rotated result is stored in the Accumulator and the contents of the Data
Memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); (i = 0~6)
ACC.7 ¬ [m].0
Affected flag(s)
None
RRC [m]
Rotate Data Memory right through Carry
Description
The contents of the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0
replaces the Carry bit and the original carry flag is rotated into bit 7.
Operation
[m].i ¬ [m].(i+1); (i = 0~6)
[m].7 ¬ C
C ¬ [m].0
Affected flag(s)
C
RRCA [m]
Rotate Data Memory right through Carry with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0 replaces the Carry bit and the original carry flag is rotated into bit 7. The rotated result is
stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); (i = 0~6)
ACC.7 ¬ C
C ¬ [m].0
Affected flag(s)
C
Rev. 1.40
56
April 19, 2011
HT83F02
SBC A,[m]
Subtract Data Memory from ACC with Carry
Description
The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Accumulator. Note that if the result
of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or
zero, the C flag will be set to 1.
Operation
ACC ¬ ACC - [m] - C
Affected flag(s)
OV, Z, AC, C
SBCM A,[m]
Subtract Data Memory from ACC with Carry and result in Data Memory
Description
The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is
positive or zero, the C flag will be set to 1.
Operation
[m] ¬ ACC - [m] - C
Affected flag(s)
OV, Z, AC, C
SDZ [m]
Skip if decrement Data Memory is 0
Description
The contents of the specified Data Memory are first decremented by 1. If the result is 0 the
following instruction is skipped. As this requires the insertion of a dummy instruction while
the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program
proceeds with the following instruction.
Operation
[m] ¬ [m] - 1
Skip if [m] = 0
Affected flag(s)
None
SDZA [m]
Skip if decrement Data Memory is zero with result in ACC
Description
The contents of the specified Data Memory are first decremented by 1. If the result is 0, the
following instruction is skipped. The result is stored in the Accumulator but the specified
Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not
0, the program proceeds with the following instruction.
Operation
ACC ¬ [m] - 1
Skip if ACC = 0
Affected flag(s)
None
SET [m]
Set Data Memory
Description
Each bit of the specified Data Memory is set to 1.
Operation
[m] ¬ FFH
Affected flag(s)
None
SET [m].i
Set bit of Data Memory
Description
Bit i of the specified Data Memory is set to 1.
Operation
[m].i ¬ 1
Affected flag(s)
None
Rev. 1.40
57
April 19, 2011
HT83F02
SIZ [m]
Skip if increment Data Memory is 0
Description
The contents of the specified Data Memory are first incremented by 1. If the result is 0, the
following instruction is skipped. As this requires the insertion of a dummy instruction while
the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program
proceeds with the following instruction.
Operation
[m] ¬ [m] + 1
Skip if [m] = 0
Affected flag(s)
None
SIZA [m]
Skip if increment Data Memory is zero with result in ACC
Description
The contents of the specified Data Memory are first incremented by 1. If the result is 0, the
following instruction is skipped. The result is stored in the Accumulator but the specified
Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not
0 the program proceeds with the following instruction.
Operation
ACC ¬ [m] + 1
Skip if ACC = 0
Affected flag(s)
None
SNZ [m].i
Skip if bit i of Data Memory is not 0
Description
If bit i of the specified Data Memory is not 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two
cycle instruction. If the result is 0 the program proceeds with the following instruction.
Operation
Skip if [m].i ¹ 0
Affected flag(s)
None
SUB A,[m]
Subtract Data Memory from ACC
Description
The specified Data Memory is subtracted from the contents of the Accumulator. The result
is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will
be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
Operation
ACC ¬ ACC - [m]
Affected flag(s)
OV, Z, AC, C
SUBM A,[m]
Subtract Data Memory from ACC with result in Data Memory
Description
The specified Data Memory is subtracted from the contents of the Accumulator. The result
is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will
be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
Operation
[m] ¬ ACC - [m]
Affected flag(s)
OV, Z, AC, C
SUB A,x
Subtract immediate data from ACC
Description
The immediate data specified by the code is subtracted from the contents of the Accumulator. The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will
be set to 1.
Operation
ACC ¬ ACC - x
Affected flag(s)
OV, Z, AC, C
Rev. 1.40
58
April 19, 2011
HT83F02
SWAP [m]
Swap nibbles of Data Memory
Description
The low-order and high-order nibbles of the specified Data Memory are interchanged.
Operation
[m].3~[m].0 « [m].7 ~ [m].4
Affected flag(s)
None
SWAPA [m]
Swap nibbles of Data Memory with result in ACC
Description
The low-order and high-order nibbles of the specified Data Memory are interchanged. The
result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC.3 ~ ACC.0 ¬ [m].7 ~ [m].4
ACC.7 ~ ACC.4 ¬ [m].3 ~ [m].0
Affected flag(s)
None
SZ [m]
Skip if Data Memory is 0
Description
If the contents of the specified Data Memory is 0, the following instruction is skipped. As
this requires the insertion of a dummy instruction while the next instruction is fetched, it is a
two cycle instruction. If the result is not 0 the program proceeds with the following instruction.
Operation
Skip if [m] = 0
Affected flag(s)
None
SZA [m]
Skip if Data Memory is 0 with data movement to ACC
Description
The contents of the specified Data Memory are copied to the Accumulator. If the value is
zero, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the
program proceeds with the following instruction.
Operation
ACC ¬ [m]
Skip if [m] = 0
Affected flag(s)
None
SZ [m].i
Skip if bit i of Data Memory is 0
Description
If bit i of the specified Data Memory is 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two
cycle instruction. If the result is not 0, the program proceeds with the following instruction.
Operation
Skip if [m].i = 0
Affected flag(s)
None
TABRDC [m]
Read table (current page) to TBLH and Data Memory
Description
The low byte of the program code (current page) addressed by the table pointer (TBLP) is
moved to the specified Data Memory and the high byte moved to TBLH.
Operation
[m] ¬ program code (low byte)
TBLH ¬ program code (high byte)
Affected flag(s)
None
TABRDL [m]
Read table (last page) to TBLH and Data Memory
Description
The low byte of the program code (last page) addressed by the table pointer (TBLP) is
moved to the specified Data Memory and the high byte moved to TBLH.
Operation
[m] ¬ program code (low byte)
TBLH ¬ program code (high byte)
Affected flag(s)
None
Rev. 1.40
59
April 19, 2011
HT83F02
XOR A,[m]
Logical XOR Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical XOR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²XOR² [m]
Affected flag(s)
Z
XORM A,[m]
Logical XOR ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical XOR operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²XOR² [m]
Affected flag(s)
Z
XOR A,x
Logical XOR immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical XOR
operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²XOR² x
Affected flag(s)
Z
Rev. 1.40
60
April 19, 2011
HT83F02
Package Information
28-pin SOP (300mil) Outline Dimensions
2 8
1 5
A
B
1
1 4
C
C '
G
D
E
H
a
F
· MS-013
Symbol
Nom.
Max.
A
0.393
¾
0.419
B
0.256
¾
0.300
C
0.012
¾
0.020
C¢
0.697
¾
0.713
D
¾
¾
0.104
E
¾
0.050
¾
F
0.004
¾
0.012
G
0.016
¾
0.050
H
0.008
¾
0.013
a
0°
¾
8°
Symbol
A
Rev. 1.40
Dimensions in inch
Min.
Dimensions in mm
Min.
Nom.
Max.
9.98
¾
10.64
B
6.50
¾
7.62
C
0.30
¾
0.51
C¢
17.70
¾
18.11
D
¾
¾
2.64
E
¾
1.27
¾
F
0.10
¾
0.30
G
0.41
¾
1.27
H
0.20
¾
0.33
a
0°
¾
8°
61
April 19, 2011
HT83F02
Product Tape and Reel Specifications
Reel Dimensions
D
T 2
A
C
B
T 1
SOP 28W (300mil)
Symbol
Description
Dimensions in mm
A
Reel Outer Diameter
330.0±1.0
B
Reel Inner Diameter
100.0±1.5
C
Spindle Hole Diameter
D
Key Slit Width
T1
Space Between Flange
T2
Reel Thickness
Rev. 1.40
13.0
+0.5/-0.2
2.0±0.5
24.8
+0.3/-0.2
30.2±0.2
62
April 19, 2011
HT83F02
Carrier Tape Dimensions
P 0
D
P 1
t
E
F
W
D 1
P
C
B 0
K 0
A 0
R e e l H o le
IC
p a c k a g e p in 1 a n d th e r e e l h o le s
a r e lo c a te d o n th e s a m e s id e .
SOP 28W (300mil)
Symbol
Description
Dimensions in mm
W
Carrier Tape Width
24.0±0.3
P
Cavity Pitch
12.0±0.1
E
Perforation Position
1.75±0.10
F
Cavity to Perforation (Width Direction)
11.5±0.1
D
Perforation Diameter
1.5
D1
Cavity Hole Diameter
1.50
P0
Perforation Pitch
4.0±0.1
P1
Cavity to Perforation (Length Direction)
2.0±0.1
A0
Cavity Length
10.85±0.10
B0
Cavity Width
18.34±0.10
K0
Cavity Depth
2.97±0.10
t
Carrier Tape Thickness
0.35±0.01
C
Cover Tape Width
21.3±0.1
Rev. 1.40
63
+0.1/-0.0
+0.25/-0.00
April 19, 2011
HT83F02
Holtek Semiconductor Inc. (Headquarters)
No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan
Tel: 886-3-563-1999
Fax: 886-3-563-1189
http://www.holtek.com.tw
Holtek Semiconductor Inc. (Taipei Sales Office)
4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan
Tel: 886-2-2655-7070
Fax: 886-2-2655-7373
Fax: 886-2-2655-7383 (International sales hotline)
Holtek Semiconductor Inc. (Shenzhen Sales Office)
5F, Unit A, Productivity Building, No.5 Gaoxin M 2nd Road, Nanshan District, Shenzhen, China 518057
Tel: 86-755-8616-9908, 86-755-8616-9308
Fax: 86-755-8616-9722
Holtek Semiconductor (USA), Inc. (North America Sales Office)
46729 Fremont Blvd., Fremont, CA 94538
Tel: 1-510-252-9880
Fax: 1-510-252-9885
http://www.holtek.com
Copyright Ó 2011 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used
solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable
without further modification, nor recommends the use of its products for application that may present a risk to human life
due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices
or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information,
please visit our web site at http://www.holtek.com.tw.
Rev. 1.40
64
April 19, 2011