ML6206S ML6206S Series Low ESR Cap. Compatible Positive Voltage Regulator Application Features Battery Powered Equipment Palmtops Portable Cameras and Video Recorders Reference Voltage Sources General Description CMOS Low Power Consumption : Typical 1.0uAat Vout=3.0V Output Voltage Range : 1.5V to 5.0V in 0.1V increments HighlyAccurate: Output Voltage + 3% for 1.5V to 1.9V Output Voltage + 2% for 2.0V to 5.0V Maximum Output Current: 250mA (within the maximum power dissipation, Vout=5.0V) Small Input-Output Voltage Differential: 0.16V at 100mAand 0.4V at 200mA Input stability: Typ. 0.2%/V PackageAvailable: SOT- 23 (250mW), SOT- 89 (500mW) & TO - 92 (300mW) Reverse Battery Protection Block Diagram The ML6206S series are highly precise, low power consumption, high voltage, positive voltage output, three-pin regulator. It provides high output current even when the input/output voltage differential is small. The ML6206S consists of a high-precision voltage reference, an error correction circuit and reverse battery protection. Absolute Maximum Ratings Parameter Input Voltage Output Current Output Voltage SOT-23 Continuous Total Power Dissipation SOT-89 TO-92 Operating Ambient Temperature Storage Temperature Symbol VIN IOUT VOUT Ratings 6 500 VSS-0.3 ~VIN+0.3 250 Units V mA V Pd 500 mW Topr Tstg 300 -40 ~ +70 -40 ~ +70 P1/14 o C C o November 2009 ML6206S Pin Configuration SOT-23 Package Pin Number SOT23 SOT89 TO-92 1 1 1 3 2 2 2 3 3 SOT-89 TO-92 Pin Name Function VSS VIN VOUT Ground Power Input Output Standard Circuit Note on Use 1. Oscillation may occur as a result of the impedance present between the power supply and the IC’s input. Please use a capacitor (CIN) of at least 1uF, when the impedance is 10 ohm or more. With a large output current, Voltage output can be stabilised by increasing capacitor (CIN) size. If CIN is small and capacitor (CL) size is increased, oscillation may occur. In such cases, Voltage output can be stabilised by either increasing the size of CIN or decreasing the size of CL. 2. Please ensure that output current (IOUT) is less than Pd / (VIN-VOUT) and does not exceed the stipulated Continuous Total Power Dissipation value (Pd). Test Circuit Test Circuit 2 Test Circuit 1 P2/14 November 2009 ML6206S Electrical Characteristic ML6206S302 VOUT(T)=3.0V(Note 1) Parameter Output Voltage Maximum Output Current Load Stability Input –Output Voltage Differential (Note 3) Supply Current Input Stability Input Voltage Current Limiter Symbol VOUT(E) (Note 2) IOUT max VOUT Vdif1 Vdif2 ISS VOUT VIN * VOUT VIN Ishort Conditions IOUT=40mA VIN=4.0V VIN=4.0V, VOUT(E) 2.7V VIN=4.0V, 1mAIOUT100mA IOUT=80mA IOUT=150mA VIN=4.0V IOUT=40mA VOUT(T)+1.0VVIN6V Min Typ Max Units Circuit 2.940 3.000 3.060 V 1 mA mV mV mV uA 1 1 1 1 2 0.30 %V 1 6 V mA 1 350 25 80 250 1.0 0.01 1.8 VIN = VOUT+1.5V, VOUT=VSS 100 Note : 1. VOUT(T) = Specified Output Voltage. 2. VOUT(E) = Effective Output Voltage (i.e. the output voltage when (VOUT(T)+1.0V) is provided at the VIN pin while maintaining a certain IOUT value). 3. Vdif = VIN1(Note 4) – VOUT(E) 4. VIN1 = The input voltage at the time 98% of VOUT (E) is output (input voltage has been gradually reduced). P3/14 November 2009 ML6206S Typical Performance Characteristics 1) Output Voltage vs. Output Current ML6206S153 ML6206S302 2) Current Limit ML6206S153 ML6206S302 P4/14 ML6206S502 November 2009 ML6206S 3) Output Voltage vs. Input Voltage ML6206S153 ML6206S302 4) Supply Current vs. Input Voltage ML6206S153 ML6206S302 5) Output Voltage vs. Ambient Temperature ML6206S153 ML6206S302 P5/14 November 2009 ML6206S 6) Supply Current vs. Ambient Temperature ML6206S153 ML6206S302 7) Input Transient Response 1 ML6206S153 P6/14 November 2009 ML6206S ML6206S302 8) Input Transient Response 2 ML6206S153 ML6206S302 P7/14 November 2009 ML6206S 9) Load Transient Response ML6206S272 Load Current 50mA to 100mA Load Current 10mA to 50mA Load Current 10mA to 100mA P8/14 November 2009 ML6206S 10) Power Supply Rejection Ratio ML6206S153 ML6206S153 ML6206S302 ML6206S302 Ordering Information Designator ①② ③ ④ ⑤ ⑥ Description Output Voltage eg. 30=3.0V 50=5.0V Output Voltage Accuracy 2 = + 2.0% 3 = + 3.0% Package Type M = SOT-23 P = SOT-89 T = TO-92 Device Orientation R = Embossed Tape (Orientation of Device : Right) L = Embossed Tape (Orientation of Device : Left) B = Bag (TO-92) H = Paper Tape (TO-92) ML6206S①②③④⑤⑥ G = ROHS Part P9/14 November 2009 ML6206S Marking SOT-23 : Designator Description 1 Type Y = Positive Voltage Regulator 2,3 Output Voltage eg. 30 = 3.0V 4 Internal Code SOT-89 : Designator 1 2,3 4 5 Description Type Y = Positive Voltage Regulator Output Voltage eg. 30 = 3.0V Output Voltage Accuracy 2 = + 2.0% 3 = + 3.0% Internal Code TO-92 : Designator 1 2,3 4 5 6, 7 8, 9 Description Type Y = Positive Voltage Regulator Output Voltage eg. 30 = 3.0V Output Voltage Accuracy 2 = + 2.0% 3 = + 3.0% Internal code Year Code eg. 09 = Year 2009 Week Code eg. 10 = Week 10 P10/14 November 2009 ML6206S Packaging Information SOT-89 : SOT-23 : (0.8) 0.15 0.4 -0.1 -0.05 1.5 0.1 4.5 0.1 -0.1 -0.05 1.72 0.1 1.1 mm min. 0.2 4.25 max 2.45 0.15 +1.2 -0.0.1 1.6 2.8 0.2 0 ~ 0.1 (0.95) 0.42 0.06 0.42 0.06 0.4 0.04 1.1 0.1 1.9 0.2 0.49 0.06 2.9 0.2 1.5 0.1 1.5 0.1 TO-92 : 1.27 4.2 max 1.27 5.2 max 12.7 min 5.3 max Units : mm Recommended Pattern Layout 2.2 2.4 0.9 SOT-89 : 3.7 SOT-23 : 45º 1.5 1.9 0.8 45º 1.0 1. 0 1.0 1.6 P11/14 November 2009 ML6206S Tape and Reel Information SOT-23 : SIZE (mm) A 178 0.8 B 2 0.2 C 13 0.2 D 21 0.8 G 8 0.5 H 60 3,000 pcs / reel SOT-23 Taping Specifications : 4 0.1 1.5 + 0.1 -0 4 0.1 8 0.2 3.5 0.05 1.75 0.1 2 0.05 1.1 0.1 Direction of feed Direction of feed “L” type Orientation of Device: Left Reverse Type “R” type Orientation of Device: Right Standard Type P12/14 November 2009 ML6206S SOT-89 : SIZE (mm) B 2 0.2 C 13 0.2 D 21 0.8 G 12 0.5 H 60 1.5 + 0.1 0 12.0 0.2 5.65 0.05 1.5 0.1 2.0 0.05 178 0.8 1,000 pcs / reel SOT-89 Taping Specifications : 4.0 0.1 A 8.0 0.1 Direction of feed Direction of feed “L” type Orientation of Device: Left Reverse Type “R” type Orientation of Device: Right Standard Type P13/14 November 2009 ML6206S TO-92 Taping Specifications : W W1 WO L1 H0 H W2 H1 P P2 t F D PO P PO P2 SIZE (mm) 12.7 1.0 12.7 0.3 6.35 0.4 F 2.5 -0.15 W WO W1 W2 H H0 H1 D t L1 18.0 1.0 6.0 0.3 9.0 0.5 0.5 MAX 19.0 0.5 16.0 0.5 32.25 MAX 4.0 0.2 0.6 0.2 3.5 MIN 2,000 pcs / box +0.45 Minilogic reserves the rights to change the information and specifications without prior notice.The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. P14/14 November 2009