ISL83070EIBZA

ISL83070E, ISL83071E, ISL83072E, ISL83073E,
ISL83075E, ISL83076E, ISL83077E, ISL83078E
Data Sheet
October 5, 2012
±15kV ESD Protected, 3.3V, Full Fail-safe,
Low Power, High Speed or Slew Rate
Limited, RS-485/RS-422 Transceivers
The Intersil ISL8307XE are BiCMOS 3.3V powered, single
transceivers that meet both the RS-485 and RS-422
standards for balanced communication. These devices have
very low bus currents (+125mA/-100mA), so they present a
true “1/8 unit load” to the RS-485 bus. This allows up to 256
transceivers on the network without violating the RS-485
specification’s 32 unit load maximum, and without using
repeaters. For example, in a remote utility meter reading
system, individual meter readings are routed to a
concentrator via an RS-485 network, so the high allowed
node count minimizes the number of repeaters required.
Receiver (Rx) inputs feature a “Full Fail-Safe” design, which
ensures a logic high Rx output if Rx inputs are floating,
shorted, or terminated but undriven.
FN6115.5
Features
• Pb-Free (RoHS Compliant)
• RS-485 I/O Pin ESD Protection . . . . . . . . . . . . . ±15kV HBM
- Class 3 ESD Level on all Other Pins . . . . . . >7kV HBM
• Full Fail-safe (Open, Short, Terminated/Floating)
Receivers
• Hot Plug - Tx and Rx Outputs Remain Three-state During
Power-up (Only Versions with Output Enable Pins)
• True 1/8 Unit Load Allows up to 256 Devices on the Bus
• Single 3.3V Supply
• High Data Rates . . . . . . . . . . . . . . . . . . . . . . up to 20Mbps
• Low Quiescent Supply Current . . . . . . . . . . .800μA (Max)
- Ultra Low Shutdown Supply Current . . . . . . . . . . .10nA
• -7V to +12V Common Mode Input/Output Voltage Range
Hot Plug circuitry ensures that the Tx and Rx outputs remain
in a high impedance state while the power supply stabilizes.
• Half and Full Duplex Pinouts
The ISL83070E through ISL83075E utilize slew rate limited
drivers which reduce EMI, and minimize reflections from
improperly terminated transmission lines, or unterminated
stubs in multidrop and multipoint applications. Slew rate limited
versions also include receiver input filtering to enhance noise
immunity in the presence of slow input signals.
• Current Limiting and Thermal Shutdown for driver
Overload Protection
The ISL83070E, ISL83071E, ISL83073E, ISL83076E,
ISL83077E are configured for full duplex (separate Rx input
and Tx output pins) applications. The half duplex versions
multiplex the Rx inputs and Tx outputs to allow transceivers
with output disable functions in 8 lead packages.
• Three State Rx and Tx Outputs Available
• Tiny MSOP package offering saves 50% board space
Applications
• Automated Utility Meter Reading Systems
• High Node Count Systems
• Field Bus Networks
• Security Camera Networks
• Building Environmental Control/ Lighting Systems
• Industrial/Process Control Networks
TABLE 1. SUMMARY OF FEATURES
PART
NUMBER
HALF/FULL DATA RATE
DUPLEX
(Mbps)
SLEW-RATE
LIMITED?
HOT
PLUG?
# DEVICES
ON BUS
RX/TX
ENABLE?
QUIESCENT
ICC (μA)
LOW POWER
SHUTDOWN?
PIN
COUNT
ISL83070E
FULL
0.25
YES
YES
256
YES
510
YES
14
ISL83071E
FULL
0.25
YES
NO
256
NO
510
NO
8
ISL83072E
HALF
0.25
YES
YES
256
YES
510
YES
8
ISL83073E
FULL
0.5
YES
YES
256
YES
510
YES
14
ISL83075E
HALF
0.5
YES
YES
256
YES
510
YES
8
ISL83076E
FULL
20
NO
YES
256
YES
510
YES
14
ISL83077E
FULL
20
NO
NO
256
NO
510
NO
8
ISL83078E
HALF
20
NO
YES
256
YES
510
YES
8
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2005-2007, 2012. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Pinouts
RO 1
R
RE 2
DE 3
DI 4
D
8
VCC
VCC 1
7
B/Z
RO 2
6
A/Y
5
GND
ISL83070E, ISL83073E, ISL83076E
(14 LD SOIC)
TOP VIEW
ISL83071E, ISL83077E
(8 LD SOIC)
TOP VIEW
ISL83072E, ISL83075E, ISL83078E
(8 LD MSOP, SOIC)
TOP VIEW
R
DI 3
GND 4
D
8
A
7
B
6
Z
5
Y
14 VCC
NC 1
RO 2
13 NC
R
RE 3
11 B
DE 4
DI 5
Ordering Information
PART NUMBER
PART
(Notes 1, 2, 3) MARKING
ISL83070EIBZA 83070EIBZ
-40 to 85 14 Ld SOIC M14.15
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL83071EIBZA 83071 EIBZ -40 to 85 8 Ld SOIC
M8.15
ISL83072EIBZA 83072 EIBZ -40 to 85 8 Ld SOIC
M8.15
ISL83072EIUZA 3072Z
-40 to 85 8 Ld MSOP M8.118
ISL83073EIBZA 83073EIBZ
-40 to 85 14 Ld SOIC M14.15
ISL83075EIBZA 83075 EIBZ -40 to 85 8 Ld SOIC
GND 6
9 Y
GND 7
8 NC
TRANSMITTING
INPUTS
-40 to 85 8 Ld MSOP M8.118
ISL83076EIBZA 83076EIBZ
-40 to 85 14 Ld SOIC M14.15
ISL83077EIBZA 83077 EIBZ -40 to 85 8 Ld SOIC
M8.15
ISL83078EIBZA 83078 EIBZ -40 to 85 8 Ld SOIC
M8.15
-40 to 85 8 Ld MSOP M8.118
NOTES:
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details
on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special
Pb-free material sets, molding compounds/die attach materials,
and 100% matte tin plate plus anneal (e3 termination finish,
which is RoHS compliant and compatible with both SnPb and
Pb-free soldering operations). Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or
exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device
information page for ISL83070E, ISL83071E, ISL83072E,
ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E.
For more information on MSL please see tech brief TB363.
OUTPUTS
RE
DE
DI
Z
Y
X
1
1
0
1
X
1
0
1
0
0
0
X
High-Z
High-Z
1
0
X
High-Z*
High-Z*
M8.15
ISL83075EIUZA 3075Z
2
10 Z
D
Truth Tables
TEMP.
RANGE
(°C)
ISL83078EIUZA 3078Z
12 A
NOTE: *Shutdown Mode (See Note 10), except for ISL83071E/77E
RECEIVING
INPUTS
RE
DE
DE
Half Duplex Full Duplex
OUTPUT
A-B
RO
0
0
X
≥ -0.05V
1
0
0
X
≤ -0.2V
0
0
0
X
Inputs
Open/Shorted
1
1
0
0
X
High-Z*
1
1
1
X
High-Z
NOTE: *Shutdown Mode (See Note 10), except for ISL83071E/77E
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Pin Descriptions
PIN
FUNCTION
RO
Receiver output: If A - B ≥ -50mV, RO is high; If A - B ≤ -200mV, RO is low; RO = High if A and B are unconnected (floating) or shorted.
RE
Receiver output enable. RO is enabled when RE is low; RO is high impedance when RE is high. If the Rx enable function isn’t
required, connect RE directly to GND or through a 1kΩ to 3kΩ resistor to GND.
DE
Driver output enable. The driver outputs, Y and Z, are enabled by bringing DE high, and are high impedance when DE is low. If the
Tx enable function isn’t required, connect DE to VCC through a 1kΩ to 3kΩ resistor.
DI
Driver input. A low on DI forces output Y low and output Z high. Similarly, a high on DI forces output Y high and output Z low.
GND
Ground connection.
A/Y
±15kV HBM ESD Protected RS-485/RS-422 level, noninverting receiver input and noninverting driver output. Pin is an input if DE =
0; pin is an output if DE = 1.
B/Z
±15kV HBM ESD Protected RS-485/RS-422 level, Inverting receiver input and inverting driver output. Pin is an input if DE = 0; pin is
an output if DE = 1.
A
±15kV HBM ESD Protected RS-485/RS-422 level, noninverting receiver input.
B
±15kV HBM ESD Protected RS-485/RS-422 level, inverting receiver input.
Y
±15kV HBM ESD Protected RS-485/RS-422 level, noninverting driver output.
Z
±15kV HBM ESD Protected RS-485/RS-422 level, inverting driver output.
VCC
System power supply input (3.0V to 3.6V).
NC
No Connection.
3
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Typical Operating Circuits
+3.3V
+3.3V
+
8
0.1µF
0.1µF
+
8
VCC
1 RO
VCC
R
D
2 RE
B/Z
7
3 DE
A/Y
6
4 DI
RT
RT
DI 4
7
B/Z
DE 3
6
A/Y
RE 2
RO 1
R
D
GND
GND
5
5
ISL83072E, ISL83075E, ISL83078E
+3.3V
+3.3V
+
1
0.1µF
0.1µF
+
1
VCC
RT
A 8
2 RO
3 DI
VCC
R
B 7
RT
Z 6
Y
6
Z
D
7 B
Y 5
D
5
RO 2
R
8 A
GND
GND
4
4
DI 3
ISL83071E, ISL83077E
+3.3V
+3.3V
+
14
VCC
2 RO
R
A 12
0.1µF
0.1µF
RT
+
14
VCC
9 Y
B 11
D
10 Z
3 RE
DE 4
RE 3
4 DE
5 DI
DI 5
RT
Z 10
Y 9
D
11 B
R
12 A
GND
RO 2
GND
6, 7
6, 7
ISL83070E, ISL83073E, ISL83076E
4
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Absolute Maximum Ratings
Thermal Information
VCC to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Input Voltages
DI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V
DE, RE (Note 20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V
Input/Output Voltages
A, B, Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -9V to +13V
RO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (VCC +0.3V)
Short Circuit Duration
Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . See Specification Table
Thermal Resistance (Typical, Note 4)
θJA (°C/W)
8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . .
105
8 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . . .
140
14 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .
128
Maximum Junction Temperature (Plastic Package) . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
4. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications
Test Conditions: VCC = 3.0V to 3.6V; Unless Otherwise Specified. Typicals are at VCC = 3.3V, TA = +25°C
(Note 5).
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
(Note 19)
TYP
MAX
(Note 19) UNITS
DC CHARACTERISTICS
VOD
Driver Differential VOUT
RL = 100Ω (RS-422) (Figure 1A, Note 16)
Full
2
2.3
-
V
RL = 54Ω (RS-485) (Figure 1A)
Full
1.5
2
VCC
V
-
-
VCC
No Load
Change in Magnitude of Driver
Differential VOUT for
Complementary Output States
Driver Common-Mode VOUT
Change in Magnitude of Driver
Common-Mode VOUT for
Complementary Output States
Logic Input High Voltage
Logic Input Low Voltage
Logic Input Hysteresis
RL = 60Ω, -7V ≤ VCM ≤ 12V (Figure 1B)
Full
1.5
2.2
-
V
ΔVOD
RL = 54Ω or 100Ω (Figure 1A)
Full
-
0.01
0.2
V
VOC
RL = 54Ω or 100Ω (Figure 1A)
Full
-
2
3
V
ΔVOC
RL = 54Ω or 100Ω (Figure 1A)
Full
-
0.01
0.2
V
VIH
DI, DE, RE
Full
2
-
-
V
VIL
DI, DE, RE
Full
-
-
0.8
V
DE, RE, (Note 15)
25
-
100
-
mV
VHYS
Logic Input Current
IIN1
DI = DE = RE = 0V or VCC, (Note 18)
Full
-2
-
2
μA
Input Current (A, B, A/Y, B/Z)
IIN2
DE = 0V, VCC = 0V or
3.6V
VIN = 12V
Full
-
80
125
μA
VIN = -7V
Full
-100
-50
-
μA
RE = 0V, DE = 0V,
VCC = 0V or 3.6V
VIN = 12V
Full
-
10
40
μA
VIN = -7V
Full
-40
-10
-
μA
VIN = 12V
Full
-
10
40
μA
VIN = -7V
Full
-40
-10
-
μA
DE = VCC, -7V ≤ VY or VZ ≤ 12V (Note 7)
Full
-
-
±250
mA
-7V ≤ VCM ≤ 12V
Full
-200
-125
-50
mV
VCM = 0V
25
-
15
-
mV
Output Leakage Current (Y, Z) (Full
Duplex Versions Only, Note 13)
IIN3
Output Leakage Current (Y, Z)
in Shutdown Mode (Full Duplex,
Note 13)
IIN4
IOSD1
Driver Short-Circuit Current,
VO = High or Low
Receiver Differential Threshold
Voltage
VTH
ΔVTH
Receiver Input Hysteresis
5
RE = VCC, DE = 0V,
VCC = 0V or 3.6V
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Electrical Specifications
Test Conditions: VCC = 3.0V to 3.6V; Unless Otherwise Specified. Typicals are at VCC = 3.3V, TA = +25°C
(Note 5). (Continued)
PARAMETER
SYMBOL
Receiver Output High Voltage
TEST CONDITIONS
TEMP
(°C)
MIN
(Note 19)
TYP
MAX
(Note 19) UNITS
Full
VCC - 0.6
-
-
VOH
IO = -4mA, VID = -50mV
Receiver Output Low Voltage
VOL
IO = -4mA, VID = -200mV
Full
-
0.17
0.4
V
Three-State (high impedance)
Receiver Output Current (Note 13)
IOZR
0.4V ≤ VO ≤ 2.4V
Full
-1
0.015
1
μA
Receiver Input Resistance
RIN
-7V ≤ VCM ≤ 12V
Full
96
150
-
kΩ
0V ≤ VO ≤ VCC
Full
±7
30
±60
mA
Full
-
150
-
°C
DE = VCC,
RE = 0V or VCC
Full
-
510
800
μA
DE = 0V, RE = 0V
Full
-
480
700
μA
DE = 0V, RE = VCC, DI = 0V or VCC
Full
-
0.01
1
μA
RS-485 Pins (A, Y, B, Z)
Human Body Model (HBM), Pin to GND
25
-
±15
-
kV
All Other Pins
HBM, per MIL-STD-883 Method 3015
25
−
>±7
-
kV
VOD = ±1.5V, CD = 820pF (Figure 4, Note 17)
Full
250
800
-
kbps
Receiver Short-Circuit Current
IOSR
Thermal Shutdown Threshold
TSD
V
SUPPLY CURRENT
No-Load Supply Current (Note 6)
ICC
Shutdown Supply Current
(Note 13)
ISHDN
DI = 0V or VCC
ESD PERFORMANCE
DRIVER SWITCHING CHARACTERISTICS (ISL83070E, ISL83071E, ISL83072E, 250kbps)
Maximum Data Rate
fMAX
Driver Differential Output Delay
tDD
RDIFF = 54Ω, CD = 50pF (Figure 2)
Full
250
1100
1500
ns
Driver Differential Output Skew
tSKEW
RDIFF = 54Ω, CD = 50pF (Figure 2)
Full
-
6
100
ns
tR, tF
RDIFF = 54Ω, CD = 50pF (Figure 2)
Full
350
960
1600
ns
Driver Differential Rise or Fall Time
Driver Enable to Output High
tZH
RL = 500Ω, CL = 50pF, SW = GND (Figure 3),
(Notes 8, 13)
Full
-
26
600
ns
Driver Enable to Output Low
tZL
RL = 500Ω, CL = 50pF, SW = VCC (Figure 3),
(Notes 8, 13)
Full
-
200
600
ns
Driver Disable from Output High
tHZ
RL = 500Ω, CL = 50pF, SW = GND (Figure 3),
(Note 13)
Full
-
28
55
ns
Driver Disable from Output Low
tLZ
RL = 500Ω, CL = 50pF, SW = VCC (Figure 3),
(Note 13)
Full
-
30
55
ns
(Notes 10, 13)
Full
50
200
600
ns
Time to Shutdown
tSHDN
Driver Enable from Shutdown to
Output High
tZH(SHDN) RL = 500Ω, CL = 50pF, SW = GND (Figure 3),
(Notes 10, 11, 13)
Full
-
180
700
ns
Driver Enable from Shutdown to
Output Low
tZL(SHDN)
RL = 500Ω, CL = 50pF, SW = VCC (Figure 3),
(Notes 10, 11, 13)
Full
-
100
700
ns
VOD = ±1.5V, CD = 820pF (Figure 4, Note 17)
Full
500
1600
-
kbps
DRIVER SWITCHING CHARACTERISTICS (ISL83073E, ISL83075E, 500kbps)
Maximum Data Rate
fMAX
Driver Differential Output Delay
tDD
RDIFF = 54Ω, CD = 50pF (Figure 2)
Full
180
350
800
ns
Driver Differential Output Skew
tSKEW
RDIFF = 54Ω, CD = 50pF (Figure 2)
Full
-
1
30
ns
tR, tF
Driver Differential Rise or Fall Time
RDIFF = 54Ω, CD = 50pF (Figure 2)
Full
200
380
800
ns
Driver Enable to Output High
tZH
RL = 500Ω, CL = 50pF, SW = GND (Figure 3),
(Notes 8, 13)
Full
-
26
350
ns
Driver Enable to Output Low
tZL
RL = 500Ω, CL = 50pF, SW = VCC (Figure 3),
(Notes 8, 13)
Full
-
100
350
ns
6
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Electrical Specifications
Test Conditions: VCC = 3.0V to 3.6V; Unless Otherwise Specified. Typicals are at VCC = 3.3V, TA = +25°C
(Note 5). (Continued)
PARAMETER
TEMP
(°C)
MIN
(Note 19)
TYP
RL = 500Ω, CL = 50pF, SW = GND (Figure 3),
(Note 13)
Full
-
28
55
ns
RL = 500Ω, CL = 50pF, SW = VCC (Figure 3),
(Note 13)
Full
-
30
55
ns
(Notes 10, 13)
Full
50
200
600
ns
SYMBOL
TEST CONDITIONS
Driver Disable from Output High
tHZ
Driver Disable from Output Low
tLZ
Time to Shutdown
tSHDN
MAX
(Note 19) UNITS
Driver Enable from Shutdown to
Output High
tZH(SHDN) RL = 500Ω, CL = 50pF, SW = GND (Figure 3),
(Notes 10, 11, 13)
Full
-
180
700
ns
Driver Enable from Shutdown to
Output Low
tZL(SHDN)
RL = 500Ω, CL = 50pF, SW = VCC (Figure 3),
(Notes 10, 11, 13)
Full
-
100
700
ns
VOD = ±1.5V, CD = 350pF (Figure 4, Note 17)
Full
20
28
-
Mbps
DRIVER SWITCHING CHARACTERISTICS (ISL83076E, ISL83077E, ISL83078E, 20Mbps)
Maximum Data Rate
fMAX
Driver Differential Output Delay
tDD
RDIFF = 54Ω, CD = 50pF (Figure 2)
Full
-
27
40
ns
Driver Differential Output Skew
tSKEW
RDIFF = 54Ω, CD = 50pF (Figure 2)
Full
-
1
3
ns
ΔtDSKEW
Driver Output Skew, Part-to-Part
Driver Differential Rise or Fall Time
tR, tF
RDIFF = 54Ω, CD = 50pF (Figure 2, Note 14)
Full
-
-
11
ns
RDIFF = 54Ω, CD = 50pF (Figure 2)
Full
-
9
15
ns
Driver Enable to Output High
tZH
RL = 500Ω, CL = 50pF, SW = GND (Figure 3),
(Notes 8, 13)
Full
-
17
50
ns
Driver Enable to Output Low
tZL
RL = 500Ω, CL = 50pF, SW = VCC (Figure 3),
(Notes 8, 13)
Full
-
16
40
ns
Driver Disable from Output High
tHZ
RL = 500Ω, CL = 50pF, SW = GND (Figure 3),
(Note 13)
Full
-
25
40
ns
Driver Disable from Output Low
tLZ
RL = 500Ω, CL = 50pF, SW = VCC (Figure 3),
(Note 13)
Full
-
28
50
ns
(Notes 10, 13)
Full
50
200
600
ns
Time to Shutdown
tSHDN
Driver Enable from Shutdown to
Output High
tZH(SHDN) RL = 500Ω, CL = 50pF, SW = GND (Figure 3),
(Notes 10, 11, 13)
Full
-
180
700
ns
Driver Enable from Shutdown to
Output Low
tZL(SHDN)
RL = 500Ω, CL = 50pF, SW = VCC (Figure 3),
(Notes 10, 11, 13)
Full
-
90
700
ns
ISL83070E-75E
Full
12
20
-
Mbps
ISL83076E-78E
Full
20
35
-
Mbps
ISL83070E-75E
Full
25
70
120
ns
ISL83076E-78E
Full
25
33
60
ns
(Figure 5)
Full
-
1.5
4
ns
(Figure 5, Note 14)
Full
-
-
15
ns
RECEIVER SWITCHING CHARACTERISTICS (All Versions)
Maximum Data Rate
fMAX
Receiver Input to Output Delay
tPLH, tPHL
Receiver Skew | tPLH - tPHL |
tSKD
ΔtRSKEW
Receiver Skew, Part-to-Part
Receiver Enable to Output High
tZH
Receiver Enable to Output Low
tZL
Receiver Disable from Output High
7
tHZ
VID = ±1.5V (Note 17)
(Figure 5)
RL = 1kΩ, CL = 15pF,
SW = GND (Figure 6),
(Notes 9, 13)
ISL83070E-75E
Full
5
15
20
ns
ISL83076E-78E
Full
5
11
17
ns
RL = 1kΩ, CL = 15pF,
SW = VCC (Figure 6),
(Notes 9, 13)
ISL83070E-75E
Full
5
15
20
ns
ISL83076E-78E
Full
5
11
17
ns
RL = 1kΩ, CL = 15pF,
SW = GND (Figure 6),
(Note 13)
ISL83070E-75E
Full
5
12
20
ns
ISL83076E-78E
Full
4
7
15
ns
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Electrical Specifications
Test Conditions: VCC = 3.0V to 3.6V; Unless Otherwise Specified. Typicals are at VCC = 3.3V, TA = +25°C
(Note 5). (Continued)
PARAMETER
SYMBOL
Receiver Disable from Output Low
tLZ
Time to Shutdown
RL = 1kΩ, CL = 15pF,
SW = VCC (Figure 6),
(Note 13)
tSHDN
TEMP
(°C)
MIN
(Note 19)
TYP
ISL83070E-75E
Full
5
13
20
ns
ISL83076E-78E
Full
4
7
15
ns
TEST CONDITIONS
(Notes 10, 13)
MAX
(Note 19) UNITS
Full
50
180
600
ns
Receiver Enable from Shutdown to
Output High
tZH(SHDN) RL = 1kΩ, CL = 15pF, SW = GND (Figure 6),
(Notes 10, 12, 13)
Full
-
240
500
ns
Receiver Enable from Shutdown to
Output Low
tZL(SHDN)
RL = 1kΩ, CL = 15pF, SW = VCC (Figure 6),
(Notes 10, 12, 13)
Full
-
240
500
ns
NOTES:
5. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise
specified.
6. Supply current specification is valid for loaded drivers when DE = 0V.
7. Applies to peak current. See “Typical Performance Curves” for more information.
8. When testing devices with the shutdown feature, keep RE = 0 to prevent the device from entering SHDN.
9. When testing devices with the shutdown feature, the RE signal high time must be short enough (typically <100ns) to prevent the device from
entering SHDN.
10. Versions with a shutdown feature are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 50ns, the parts
are guaranteed not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See
“Low Power Shutdown Mode” on page 11.
11. Keep RE = VCC, and set the DE signal low time >600ns to ensure that the device enters SHDN.
12. Set the RE signal high time >600ns to ensure that the device enters SHDN.
13. Does not apply to the ISL83071E and ISL83077E.
14. ΔtSKEW is the magnitude of the difference in propagation delays of the specified terminals of two units tested with identical test conditions (VCC,
temperature, etc.). Only applies to the ISL83076E - 78E.
15. ISL83070E - ISL83075E only.
16. VCC ≥ 3.15V
17. Limits established by characterization and are not production tested.
18. If the Tx or Rx enable function isn’t needed, connect the enable pin to the appropriate supply (see “Pin Descriptions” table) through a 1kΩ to 3kΩ
resistor.
19. Parts are 100% tested at +25°C. Full temperature limits are guaranteed by bench and tester characterization.
20. If the DE or RE input voltage exceeds the VCC voltage by more than 500mV, then current will flow into the logic pin. The current is limited by a
340Ω resistor (so ≈13mA with VIN = 5V and VCC = 0V) so no damage will occur if VCC ≤ VIN ≤ 7V for short periods of time.
Test Circuits and Waveforms
VCC
RL/2
DE
DI
VCC
Z
DI
VOD
D
375Ω
DE
Z
VOD
D
Y
Y
RL/2
FIGURE 1A. VOD AND VOC
VOC
RL = 60Ω
VCM
-7V TO +12V
375Ω
FIGURE 1B. VOD WITH COMMON MODE LOAD
FIGURE 1. DC DRIVER TEST CIRCUITS
8
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Test Circuits and Waveforms (Continued)
3V
DI
1.5V
1.5V
0V
VCC
tPHL
tPLH
DE
Z
DI
RDIFF
D
CD
Y
SIGNAL
GENERATOR
OUT (Z)
VOH
OUT (Y)
VOL
90%
DIFF OUT (Y - Z)
+VOD
90%
10%
10%
tR
-VOD
tF
SKEW = |tPLH - tPHL|
FIGURE 2A. TEST CIRCUIT
FIGURE 2B. MEASUREMENT POINTS
FIGURE 2. DRIVER PROPAGATION DELAY AND DIFFERENTIAL TRANSITION TIMES
DE
Z
DI
500Ω
VCC
D
SIGNAL
GENERATOR
SW
Y
GND
50pF
3V
DE
NOTE 10
1.5V
1.5V
0V
tZH, tZH(SHDN)
PARAMETER
OUTPUT
RE
DI
SW
tHZ
Y/Z
X
1/0
GND
tLZ
Y/Z
X
0/1
VCC
tZH
Y/Z
0 (Note 8)
1/0
GND
tZL
Y/Z
0 (Note 8)
0/1
VCC
tZH(SHDN)
Y/Z
1 (Note 11)
1/0
GND
tZL(SHDN)
Y/Z
1 (Note 11)
0/1
VCC
OUTPUT HIGH
NOTE 10
tHZ
VOH - 0.25V
50%
OUT (Y, Z)
VOH
0V
tZL, tZL(SHDN)
tLZ
NOTE 10
VCC
OUT (Y, Z)
50%
OUTPUT LOW
FIGURE 3A. TEST CIRCUIT
VOL + 0.25V V
OL
FIGURE 3B. MEASUREMENT POINTS
FIGURE 3. DRIVER ENABLE AND DISABLE TIMES (EXCEPT ISL83071E, ISL83077E)
VCC
DE
+
Z
DI
54Ω
D
CD
Y
3V
DI
VOD
0V
-
SIGNAL
GENERATOR
+VOD
DIFF OUT (Y - Z)
-VOD
FIGURE 4A. TEST CIRCUIT
0V
FIGURE 4B. MEASUREMENT POINTS
FIGURE 4. DRIVER DATA RATE
9
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Test Circuits and Waveforms (Continued)
+1.5V
RE
GND
A
15pF
B
R
A
0V
0V
RO
-1.5V
tPLH
tPHL
VCC
SIGNAL
GENERATOR
1.5V
RO
1.5V
0V
FIGURE 5A. TEST CIRCUIT
FIGURE 5B. MEASUREMENT POINTS
FIGURE 5. RECEIVER PROPAGATION DELAY
RE
GND
B
A
R
1kΩ
RO
SW
SIGNAL
GENERATOR
NOTE 10
VCC
GND
RE
3V
1.5V
1.5V
15pF
0V
tZH, tZH(SHDN)
NOTE 10
PARAMETER
DE
A
OUTPUT HIGH
tHZ
V
VOH - 0.25V OH
SW
1.5V
RO
tHZ
X
+1.5V
GND
tLZ
X
-1.5V
VCC
tZH (Note 9)
0
+1.5V
GND
tZL, tZL(SHDN)
tZL (Note 9)
0
-1.5V
VCC
NOTE 10
tZH(SHDN) (Note 12)
0
+1.5V
GND
RO
tZL(SHDN) (Note 12)
0
-1.5V
VCC
0V
tLZ
VCC
1.5V
OUTPUT LOW
FIGURE 6A. TEST CIRCUIT
VOL + 0.25V V
OL
FIGURE 6B. MEASUREMENT POINTS
FIGURE 6. RECEIVER ENABLE AND DISABLE TIMES (EXCEPT ISL83071E, ISL83077E)
Application Information
Receiver Features
RS-485 and RS-422 are differential (balanced) data
transmission standards for use in long haul or noisy
environments. RS-422 is a subset of RS-485, so RS-485
transceivers are also RS-422 compliant. RS-422 is a pointto-multipoint (multidrop) standard, which allows only one
driver and up to 10 (assuming one unit load devices)
receivers on each bus. RS-485 is a true multipoint standard,
which allows up to 32 one unit load devices (any
combination of drivers and receivers) on each bus. To allow
for multipoint operation, the RS-485 spec requires that
drivers must handle bus contention without sustaining any
damage.
These devices utilize a differential input receiver for maximum
noise immunity and common mode rejection. Input sensitivity
is better than ±200mV, as required by the RS-422 and RS-485
specifications.
Another important advantage of RS-485 is the extended
common mode range (CMR), which specifies that the driver
outputs and receiver inputs withstand signals that range from
+12V to -7V. RS-422 and RS-485 are intended for runs as
long as 4000’, so the wide CMR is necessary to handle
ground potential differences, as well as voltages induced in
the cable by external fields.
10
Receiver input resistance of 96kΩ surpasses the RS-422
spec of 4kΩ, and is eight times the RS-485 “Unit Load (UL)”
requirement of 12kΩ minimum. Thus, these products are
known as “one-eighth UL” transceivers, and there can be up
to 256 of these devices on a network while still complying
with the RS-485 loading spec.
Receiver inputs function with common mode voltages as great
as +9V/-7V outside the power supplies (i.e., +12V and -7V),
making them ideal for long networks where induced voltages,
and ground potential differences, are realistic concerns.
All the receivers include a “full fail-safe” function that
guarantees a high level receiver output if the receiver inputs
are unconnected (floating) or shorted. Fail-safe with shorted
inputs is achieved by setting the Rx upper switching point to
-50mV, thereby ensuring that the Rx sees 0V differential as a
high input level.
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Receivers easily meet the data rates supported by the
corresponding driver, and all receiver outputs (except on the
ISL83071E and ISL83077E) are tri-statable via the active
low RE input.
Driver Features
The RS-485, RS-422 driver is a differential output device
that delivers at least 1.5V across a 54Ω load (RS-485), and
at least 2V across a 100Ω load (RS-422). The drivers feature
low propagation delay skew to maximize bit width, and to
minimize EMI.
All drivers are tri-statable via the active high DE input, except
on the ISL83071E and ISL83077E.
The 250kbps and 500kbps driver outputs are slew rate
limited to minimize EMI, and to reduce reflections in
unterminated or improperly terminated networks. Outputs of
the ISL83076E through ISL83078E drivers are not limited,
so faster output transition times allow data rates of at least
20Mbps.
Hot Plug Function
When a piece of equipment powers up, there is a period of
time where the processor or ASIC driving the RS-485 control
lines (DE, RE) is unable to ensure that the RS-485 Tx and
Rx outputs are kept disabled. If the equipment is connected
to the bus, a driver activating prematurely during power up
may crash the bus. To avoid this scenario, the ISL8307XE
versions with output enable pins incorporate a “Hot Plug”
function. During power up, circuitry monitoring VCC ensures
that the Tx and Rx outputs remain disabled for a period of time,
regardless of the state of DE and RE. This gives the
processor/ASIC a chance to stabilize and drive the RS-485
control lines to the proper states.
ESD Protection
All pins on these devices include class 3 (>7kV) Human
Body Model (HBM) ESD protection structures, but the
RS-485 pins (driver outputs and receiver inputs)
incorporate advanced structures allowing them to survive
ESD events in excess of ±15kV HBM. The RS-485 pins are
particularly vulnerable to ESD damage because they
typically connect to an exposed port on the exterior of the
finished product. Simply touching the port pins, or
connecting a cable, can cause an ESD event that might
destroy unprotected ICs. These new ESD structures
protect the device whether or not it is powered up, protect
without allowing any latchup mechanism to activate, and
without degrading the RS-485 common mode range of -7V
to +12V. This built-in ESD protection eliminates the need
for board level protection structures (e.g., transient
suppression diodes), and the associated, undesirable
capacitive load they present.
Data Rate, Cables, and Terminations
RS-485, RS-422 are intended for network lengths up to
4000’, but the maximum system data rate decreases as the
transmission length increases. Devices operating at 20Mbps
are limited to lengths less than 100’, while the 250kbps
11
versions can operate at full data rates with lengths of several
thousand feet.
Twisted pair is the cable of choice for RS-485, RS-422
networks. Twisted pair cables tend to pick up noise and
other electromagnetically induced voltages as common
mode signals, which are effectively rejected by the
differential receivers in these ICs.
Proper termination is imperative, when using the 20Mbps
devices, to minimize reflections. Short networks using the
250kbps versions need not be terminated, but, terminations
are recommended unless power dissipation is an overriding
concern.
In point-to-point, or point-to-multipoint (single driver on bus)
networks, the main cable should be terminated in its
characteristic impedance (typically 120Ω) at the end farthest
from the driver. In multi-receiver applications, stubs
connecting receivers to the main cable should be kept as
short as possible. Multipoint (multi-driver) systems require
that the main cable be terminated in its characteristic
impedance at both ends. Stubs connecting a transceiver to
the main cable should be kept as short as possible.
Built-In Driver Overload Protection
As stated previously, the RS-485 spec requires that drivers
survive worst case bus contentions undamaged. These
devices meet this requirement via driver output short circuit
current limits, and on-chip thermal shutdown circuitry.
The driver output stages incorporate short circuit current
limiting circuitry which ensures that the output current never
exceeds the RS-485 spec, even at the common mode
voltage range extremes. Additionally, these devices utilize a
foldback circuit which reduces the short circuit current, and
thus the power dissipation, whenever the contending voltage
exceeds either supply.
In the event of a major short circuit condition, devices also
include a thermal shutdown feature that disables the drivers
whenever the die temperature becomes excessive. This
eliminates the power dissipation, allowing the die to cool. The
drivers automatically re-enable after the die temperature
drops about +15°. If the contention persists, the thermal
shutdown/re-enable cycle repeats until the fault is cleared.
Receivers stay operational during thermal shutdown.
Low Power Shutdown Mode
These CMOS transceivers all use a fraction of the power
required by their bipolar counterparts, but some also include a
shutdown feature that reduces the already low quiescent ICC to
a 10nA trickle. These devices enter shutdown whenever the
receiver and driver are simultaneously disabled (RE = VCC
and DE = GND) for a period of at least 600ns. Disabling both
the driver and the receiver for less than 50ns guarantees that
the transceiver will not enter shutdown.
Note that receiver and driver enable times increase when the
transceiver enables from shutdown. Refer to Notes 8 through
12, at the end of the “Electrical Specifications” table on page 8
for more information.
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Typical Performance Curves
VCC = 3.3V, TA = +25°C; Unless Otherwise Specified
2.35
DIFFERENTIAL OUTPUT VOLTAGE (V)
DRIVER OUTPUT CURRENT (mA)
120
100
80
60
40
20
0
0
0.5
1.0
1.5
2.0
2.5
3.0
DIFFERENTIAL OUTPUT VOLTAGE (V)
2.25
RDIFF = 100Ω
2.20
2.15
2.10
2.05
2.00
RDIFF = 54Ω
1.95
1.90
1.85
-40
3.5
-25
0
25
50
75
85
TEMPERATURE (°C)
FIGURE 7. DRIVER OUTPUT CURRENT vs DIFFERENTIAL
OUTPUT VOLTAGE
FIGURE 8. DRIVER DIFFERENTIAL OUTPUT VOLTAGE vs
TEMPERATURE
200
0.52
ISL83072/75/78E, DE = VCC, RE = X
ISL83076E/77/78E
150
0.51
Y OR Z = LOW
100
ISL83070E THRU ISL83075E
0.50
50
ICC (mA)
OUTPUT CURRENT (mA)
2.30
0
0.48
-50
Y OR Z = HIGH
-100
-150
ISL83070/73/76E, DE = X, RE = 0V; ISL83071/77E
0.49
ISL83072/75/78E, DE = 0V, RE = 0V
0.47
ISL8307XE
-7 -6
-4
-2
0
2
4
6
OUTPUT VOLTAGE (V)
8
10
0.46
-40
12
FIGURE 9. DRIVER OUTPUT CURRENT vs SHORT CIRCUIT
VOLTAGE
-25
0
25
TEMPERATURE (°C)
50
75
85
FIGURE 10. SUPPLY CURRENT vs TEMPERATURE
8.0
1220
1200
SKEW (ns)
PROPAGATION DELAY (ns)
7.5
1180
1160
1140
1120
tPHL
7.0
6.5
6.0
1100
|CROSS PT. OF Y↑ AND Z↓ - CROSS PT. OF Y↓ AND Z↑|
tPLH
1080
-40
-25
0
25
TEMPERATURE (°C)
50
75
85
FIGURE 11. DRIVER DIFFERENTIAL PROPAGATION DELAY
vs TEMPERATURE (ISL83070E, ISL83071E,
ISL83072E)
12
5.5
-40
-25
0
25
TEMPERATURE (°C)
50
75
85
FIGURE 12. DRIVER DIFFERENTIAL SKEW vs
TEMPERATURE (ISL83070E, ISL83071E,
ISL83072E)
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
VCC = 3.3V, TA = +25°C; Unless Otherwise Specified (Continued)
370
1.4
365
1.2
360
1.0
SKEW (ns)
PROPAGATION DELAY (ns)
Typical Performance Curves
355
350
340
0.6
tPHL
345
0.4
tPLH
-40
0
-25
25
TEMPERATURE (°C)
0.8
|CROSS PT. OF Y↑ AND Z↓ - CROSS PT. OF Y↓ AND Z↑|
50
0.2
-40
85
75
FIGURE 13. DRIVER DIFFERENTIAL PROPAGATION DELAY
vs TEMPERATURE (ISL83073E, ISL83075E)
-25
0
25
TEMPERATURE (°C)
50
85
75
FIGURE 14. DRIVER DIFFERENTIAL SKEW vs
TEMPERATURE (ISL83073E, ISL83075E)
0.95
32
31
0.90
PROPAGATION DELAY (ns)
30
0.85
29
SKEW (ns)
28
27
tPHL
26
tPLH
25
24
0.65
|CROSS PT. OF Y↑ AND Z↓ - CROSS PT. OF Y↓ AND Z↑|
0
25
TEMPERATURE (°C)
50
85
75
RDIFF = 54Ω, CD = 50pF
DI
5
0
5
RO
0
2.5
B/Z
2.0
1.5
1.0
A/Y
0.5
0
TIME (400ns/DIV)
FIGURE 17. DRIVER AND RECEIVER WAVEFORMS,
LOW TO HIGH (ISL83070E, ISL83071E,
ISL83072E)
13
0
25
TEMPERATURE (°C)
50
85
75
FIGURE 16. DRIVER DIFFERENTIAL SKEW vs
TEMPERATURE (ISL83076E, ISL83077E,
ISL83078E)
DRIVER OUTPUT (V)
3.0
DRIVER INPUT (V)
FIGURE 15. DRIVER DIFFERENTIAL PROPAGATION DELAY
vs TEMPERATURE (ISL83076E, ISL83077E,
ISL83078E)
-25
RDIFF = 54Ω, CD = 50pF
DI
5
0
5
RO
0
DRIVER INPUT (V)
-25
0.60
-40
RECEIVER OUTPUT (V)
22
-40
RECEIVER OUTPUT (V)
0.75
0.70
23
DRIVER OUTPUT (V)
0.80
3.0
2.5
A/Y
2.0
1.5
1.0
B/Z
0.5
0
TIME (400ns/DIV)
FIGURE 18. DRIVER AND RECEIVER WAVEFORMS,
HIGH TO LOW (ISL83070E, ISL83071E,
ISL83072E)
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
5
RO
0
3.0
2.5
B/Z
2.0
1.5
1.0
A/Y
0.5
0
DI
0
5
RO
0
3.0
2.5
A/Y
2.0
1.5
1.0
B/Z
0.5
0
TIME (200ns/DIV)
TIME (200ns/DIV)
0
5
RO
0
3.0
2.5
B/Z
2.0
1.5
1.0
RECEIVER OUTPUT (V)
5
DRIVER INPUT (V)
DI
FIGURE 20. DRIVER AND RECEIVER WAVEFORMS,
HIGH TO LOW (ISL83073E, ISL83075E)
DRIVER OUTPUT (V)
DRIVER OUTPUT (V)
RECEIVER OUTPUT (V)
FIGURE 19. DRIVER AND RECEIVER WAVEFORMS,
LOW TO HIGH (ISL83073E, ISL83075E)
RDIFF = 54Ω, CD = 50pF
A/Y
0.5
0
TIME (10ns/DIV)
FIGURE 21. DRIVER AND RECEIVER WAVEFORMS,
LOW TO HIGH (ISL83076E, ISL83077E,
ISL83078E)
14
5
DRIVER INPUT (V)
0
RDIFF = 54Ω, CD = 50pF
RDIFF = 54Ω, CD = 50pF
DI
5
0
5
RO
0
DRIVER INPUT (V)
DI
5
RECEIVER OUTPUT (V)
RDIFF = 54Ω, CD = 50pF
DRIVER INPUT (V)
VCC = 3.3V, TA = +25°C; Unless Otherwise Specified (Continued)
DRIVER OUTPUT (V)
DRIVER OUTPUT (V)
RECEIVER OUTPUT (V)
Typical Performance Curves
3.0
2.5
A/Y
2.0
1.5
1.0
B/Z
0.5
0
TIME (10ns/DIV)
FIGURE 22. DRIVER AND RECEIVER WAVEFORMS,
HIGH TO LOW (ISL83076E, ISL83077E,
ISL83078E)
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Typical Performance Curves
VCC = 3.3V, TA = +25°C; Unless Otherwise Specified (Continued)
RECEIVER OUTPUT CURRENT (mA)
35
VOL, +25°C
30
Die Characteristics
25
VOH, +25°C
20
SUBSTRATE POTENTIAL (POWERED UP):
VOL, +85°C
GND
TRANSISTOR COUNT:
15
VOH, +85°C
535
10
PROCESS:
5
0
Si Gate BiCMOS
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
RECEIVER OUTPUT VOLTAGE (V)
FIGURE 23. RECEIVER OUTPUT CURRENT vs RECEIVER
OUTPUT VOLTAGE
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
15
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Package Outline Drawing
M8.118
8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE
Rev 4, 7/11
5
3.0±0.05
A
DETAIL "X"
D
8
1.10 MAX
SIDE VIEW 2
0.09 - 0.20
4.9±0.15
3.0±0.05
5
0.95 REF
PIN# 1 ID
1
2
B
0.65 BSC
GAUGE
PLANE
TOP VIEW
0.55 ± 0.15
0.25
3°±3°
0.85±010
H
DETAIL "X"
C
SEATING PLANE
0.25 - 0.36
0.08 M C A-B D
0.10 ± 0.05
0.10 C
SIDE VIEW 1
(5.80)
NOTES:
(4.40)
(3.00)
1. Dimensions are in millimeters.
(0.65)
(0.40)
(1.40)
TYPICAL RECOMMENDED LAND PATTERN
16
2. Dimensioning and tolerancing conform to JEDEC MO-187-AA
and AMSEY14.5m-1994.
3. Plastic or metal protrusions of 0.15mm max per side are not
included.
4. Plastic interlead protrusions of 0.15mm max per side are not
included.
5. Dimensions are measured at Datum Plane "H".
6. Dimensions in ( ) are for reference only.
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Package Outline Drawing
M8.15
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 4, 1/12
DETAIL "A"
1.27 (0.050)
0.40 (0.016)
INDEX
6.20 (0.244)
5.80 (0.228)
AREA
0.50 (0.20)
x 45°
0.25 (0.01)
4.00 (0.157)
3.80 (0.150)
1
2
8°
0°
3
0.25 (0.010)
0.19 (0.008)
SIDE VIEW “B”
TOP VIEW
2.20 (0.087)
SEATING PLANE
5.00 (0.197)
4.80 (0.189)
1.75 (0.069)
1.35 (0.053)
1
8
2
7
0.60 (0.023)
1.27 (0.050)
3
6
4
5
-C-
1.27 (0.050)
0.51(0.020)
0.33(0.013)
SIDE VIEW “A
0.25(0.010)
0.10(0.004)
5.20(0.205)
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1. Dimensioning and tolerancing per ANSI Y14.5M-1994.
2. Package length does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
3. Package width does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
4. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
5. Terminal numbers are shown for reference only.
6. The lead width as measured 0.36mm (0.014 inch) or greater above the
seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch).
7. Controlling dimension: MILLIMETER. Converted inch dimensions are not
necessarily exact.
8. This outline conforms to JEDEC publication MS-012-AA ISSUE C.
17
FN6115.5
October 5, 2012
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Package Outline Drawing
M14.15
14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 1, 10/09
8.65
A 3
4
0.10 C A-B 2X
6
14
DETAIL"A"
8
0.22±0.03
D
6.0
3.9
4
0.10 C D 2X
0.20 C 2X
7
PIN NO.1
ID MARK
5
0.31-0.51
B 3
(0.35) x 45°
4° ± 4°
6
0.25 M C A-B D
TOP VIEW
0.10 C
1.75 MAX
H
1.25 MIN
0.25
GAUGE PLANE C
SEATING PLANE
0.10 C
0.10-0.25
1.27
SIDE VIEW
(1.27)
DETAIL "A"
(0.6)
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSEY14.5m-1994.
3. Datums A and B to be determined at Datum H.
(5.40)
4. Dimension does not include interlead flash or protrusions.
Interlead flash or protrusions shall not exceed 0.25mm per side.
5. The pin #1 indentifier may be either a mold or mark feature.
(1.50)
6. Does not include dambar protrusion. Allowable dambar protrusion
shall be 0.10mm total in excess of lead width at maximum condition.
7. Reference to JEDEC MS-012-AB.
TYPICAL RECOMMENDED LAND PATTERN
18
FN6115.5
October 5, 2012