MIL-PRF-38534 & 38535 CERTIFIED FACILITY
M.S.KENNEDY CORP.
RAD HARD ULTRA LOW
DROPOUT POSITIVE ADJUSTABLE
LINEAR REGULATOR
5824RH
FEATURES:
Manufactured using
Space Qualified RH1573 Die
Replaces IR OMR9604 and IRUH33PA13A
Total Dose Hardened to 300 Krads(Si) (Method 1019.7 Condition A)
Ultra Low Dropout for Reduced Power Consumption
External Shutdown Function
Latching Overload Protection
Optimized for 3.3V Input
1.265V to (VIN-0.4V) Output Voltage Range
Output Current Limit
Available in 2 Lead Form Options: Straight and Gullwing
Available to DSCC SMD 5962F09208
ELDRS Tested to 100 Krads(Si) (Method 1019.7 Condition D)
Neutron Tested to 1.0x10¹² n/cm² (Method 1017.2)
DESCRIPTION:
The MSK5824RH is a rad hard adjustable linear regulator capable of delivering 3.0 amps of output current. Typical
dropout is only 0.30 volts with a 3 amp load. An external shutdown function is ideal for power supply sequencing. This
device also has internal latching overload protection. The MSK5824RH is radiation hard and specifically designed for space/
satellite applications. The device is packaged in a hermetically sealed space efficient 8 pin flatpack that is electrically
isolated from the internal circuitry allowing for direct heat sinking.
EQUIVALENT SCHEMATIC
TYPICAL
APPLICATIONS
TYPICAL APPLICATIONS
PIN-OUT INFORMATION
Satellite System Power Supplies
Switching Power Supply Post Regulators
Constant Voltage/Current Regulators
Microprocessor Power Supplies
1
2
3
4
GND
GND
SHUTDOWN
ADJUST
8
7
6
5
VIN
VIN
VOUT
VOUT
CASE=ISOLATED
1
8548-58 Rev. H 6/14
9
ABSOLUTE MAXIMUM RATINGS
VIN
VSD
IOUT
TC
Supply Voltage
+7V
Shutdown Voltage
10v
Output Current 7
3.5A
Case Operating Temperature Range
MSK5824K/H RH
-55°C to +125°C
MSK5824RH
-40°C to +85°C
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
TST
TLD
○
Storage Temperature Range
Lead Temperature Range
(10 Seconds)
Power Dissipation
Junction Temperature
○
PD
TC
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
12
○
○
○
○
○
○
○
○
○
○
-65°C to +150°C
○
○
○
○
300°C
See SOA Curve
150°C
○
○
○
○
○
○
○
○
○
○
○
ELECTRICAL SPECIFICATIONS
NOTES:
1 Unless otherwise specified, VIN=3.3V, VSHUTDOWN=0V and IOUT=50mA. See figure 2 for typical test circuit.
2 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
3 Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise requested.
4 Military grade devices ("H" and "K" suffix) shall be 100% tested to subgroups 1,2,3 and 4.
5 Dropout limited by minimum value of VIN.
6 Subgroup 1,4 TC=+25°C
Subgroup 2
TC=+125°C
Subgroup 3
TA=-55°C
7 Output current limit is dependent upon the values of VIN and VOUT. See application notes "Over Current Latch" and "Current Limit and SOA".
8 Refer to typical performance curves.
9 Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
10 Pre and post irradiation limits at 25°C, up to 300Krad TID, are identical unless otherwise specified.
11 Reference DSCC SMD 5962F09208 for electrical specification for devices purchased as such.
12 Internal solder reflow temperature is 180°C, do not exceed.
2
8548-58 Rev. H 6/14
APPLICATION NOTES
PIN FUNCTIONS
OUTPUT CAPACITOR SELECTION
VIN- These pins provide power to all internal circuitry including bias, start-up, thermal limit and overcurrent latch. Input
voltage range is 2.9V to 6.5V but the MSK5824RH is optimized for 3.3V input. See MSK5826RH for 5V input version.
The MSK5824RH contains three internal 4.7μF tantalum
output capacitors, type CWR19HB475KCBB.The capacitor
are rated for 15V maximum applied voltage and have been
surge tested in accordance with condition B of MIL-PRF55365. The system designer must ensure proper de-rating
in accordance with their system requiremenets.
Low ESR output capacitors are required to maintain regulation and stability. Four CWR29FB227 (AVX PN
TAZH227K010L) tantalum capacitors in parallel with ceramic decoupling capacitors (0.1μF typical) provides sufficient gain and phase margin for most applications. The
maximum ESR specification for the CWR29FB227 capacitor is 180mΩ at 100kHz and is sufficient for many applications. MSK has found through full WCCA that screening for a maximum ESR of 57mΩ ensures EOL stability
criteria to be met for many applications with the most
stringent requirements. The typical ESR of the
TAZH227K010L from AVX is 49mΩ . Analysis of the final design is recommended to ensure stability requirements are met.
GND - Internally connected to ground, these pins should
be connected externally by the user to the circuit ground.
SHUTDOWN - There are two functions to the SHUTDOWN
pin. It may be used to disable the output voltage or to
reset a current latch condition. To activate the shutdown/
reset functions the user must apply a voltage greater than
1.6V to the SHUTDOWN pin. The voltage applied to the SHUTDOWN pin can be greater than the input voltage. The output
voltage will turn on when the SHUTDOWN pin is pulled below the threshold voltage. If the SHUTDOWN pin is not used,
it should be connected to ground. It should be noted that
with the shutdown pin tied to ground, a current latch condition can only be reset by cycling power off, then on.
VOUT - These are the output pins for the device.
ADJUST - This pin is used to set the output voltage. Connect a resistor between the adjust pin (4) and the output
pins (5 and 6) to fix the output voltage at the desired
value. Use the following equations to determine the nominal value of the adjust resistor (RADJ).
VOUT=VREF x (1 + RADJ/1KΩ)
RADJ=(VOUT/VREF - 1) x 1KΩ
OVERCURRENT LATCH
Overcurrent protection is provided by the MSK5824RH
series through the use of a timed latch off circuit. The
internal latch timeout is triggered by an overcurrent condition. To allow for start up surge currents, the timeout is
approximately 22mS at 25°C. If the overcurrent condition remains at the end of the timeout cycle, the regulator
will latch off until the latch is reset. To reset the latch,
toggle the shutdown pin high then low or cycle VIN off
then back on. At elevated temperatures or input voltages
the device may simply limit the output current without
activating the latch feature. A thermal limit condition will
trigger the latch with no time out delay.
FIGURE 1
INPUT POWER SUPPLY BYPASSING
CURRENT LIMIT AND SOA
The MSK5824RH contains an internal 4.7μF tantalum input capacitor, type CWR19HB475CBB. The capacitor is rated
for 15V maximum applied voltage and has been surge tested
in accordance with condition B of MIL-PRF-55365. The system designer must ensure proper de-rating in accordance
with their system requirements. To maximize transient response and minimize power supply transients it is recommended that two 47μF tantalum capacitors are connected
between VIN and ground. A 0.1μF ceramic capacitor should
also be used for high frequency bypassing. See typical application circuit.
The MSK5824RH current limit function is directly affected
by the input and output voltages. Figure 1 illustrates the relationship between VIN and ICL for various output voltages. It
is very important for the user to consult the SOA curve when
using input voltages which result in current limit conditions
beyond 3.5 Amps. When using input voltages which result in
current limit above 3.5 Amps, the user must maintain output
current within the SOA curve to avoid damage to the device.
The current limit is adjusted internally for an input voltage of
3.3V.
3
8548-58 Rev. H 6/14
APPLICATION NOTES CONT.
THERMAL LIMITING
The MSK5824RH control circuitry has a thermal shutdown temperature of approximately 150°C. This thermal shutdown can be used as a protection feature, but
for continuous operation, the junction temperature of the
pass transistor must be maintained below 150°C. Proper
heat sink selection is essential to maintain these conditions. Exceeding the thermal limit activates the latch feature of the MSK5824RH. Toggle the shutdown pin high then
low or cycle power to reset the latch. See shutdown pin
description and overcurrent latch description for more information.
TYPICAL APPLICATIONS CIRCUIT
HEAT SINK SELECTION
To select a heat sink for the MSK5824RH, the following
formula for convective heat flow may be used.
Governing Equation:
TJ = PD X (RθJC + RθCS + RθSA) + TA
Where
TJ
PD
RθJC
RθCS
RθSA
TA
=
=
=
=
=
=
Junction Temperature
Total Power Dissipation
Junction to Case Thermal Resistance
Case to Heat Sink Thermal Resistance
Heat Sink to Ambient Thermal Resistance
Ambient Temperature
Power Dissipation=(VIN-VOUT) x IOUT
Next, the user must select a maximum junction temperature. The absolute maximum allowable junction temperature is 150°C. The equation may now be rearranged
to solve for the required heat sink to ambient thermal
resistance (RθSA).
Example:
An MSK5824RH is connected for VIN=+3.3V and
VOUT=+2.5V. IOUT is a continuous 3A DC level. The ambient temperature is +25°C. The maximum desired junction temperature is +125°C.
RθJC=6.5°C/W and RθCS=0.15°C/W for most thermal
greases
Power Dissipation=(3.3V-2.5V) x (3A)
=2.4 Watts
Solve for RθSA:
RθSA=
125°C - 25°C
- 6.5°C/W - 0.15°C/W
2.4W
= 35.0°C/W
In this example, a heat sink with a thermal resistance
of no more than 35.0°C/W must be used to maintain a
junction temperature of no more than 125°C.
FIGURE 2
START UP CURRENT
The MSK5824RH sinks increased current during startup
to bring up the output voltage. Reference the "Saturated
Drive Current vs. Input Voltage graph in the typical performance curves of this data sheet and the "Understanding Startup Surge Current With MS Kennedy's RH1573
Based Rad Hard LDO Regulators" application note in the
application notes section of the MS Kennedy Web site
for more information.
http://www.mskennedy.com/
TOTAL DOSE RADIATION TEST
PERFORMANCE
Radiation performance curves for TID, Neutron and
ELDRS testing have been generated for all radiation testing performed by MS Kennedy. These curves show performance trends throughout the TID test process and
are located in the MSK5826RH radiation test report. The
complete radiation test report is available in the RAD HARD
PRODUCTS section on the MSK website.
http://www.mskennedy.com/store.asp?pid=9951&catid=19680
4
8548-58 Rev. H 6/14
TYPICAL PERFORMANCE CURVES
5
8548-58 Rev. H 6/14
MECHANICAL SPECIFICATIONS
ESD TRIANGLE INDICATES PIN 1
WEIGHT=5.8 GRAMS TYPICAL
ALL DIMENSIONS ARE SPECIFIED IN INCHES
ORDERING INFORMATION
MSK5824 K RH
LEAD CONFIGURATIONS
BLANK= STRAIGHT
RADIATION HARDENED
SCREENING
BLANK= INDUSTRIAL; H=MIL-PRF-38534 CLASS H;
K=MIL-PRF-38534 CLASS K
GENERAL PART NUMBER
The above example is a Class K regulator with straight leads.
NOTE: See DSCC SMD 5962F09208 for DSCC part number options.
6
8548-58 Rev. H 6/14
MECHANICAL SPECIFICATIONS
ESD TRIANGLE INDICATES PIN 1
WEIGHT=5.5 GRAMS TYPICAL
ALL DIMENSIONS ARE SPECIFIED IN INCHES
ORDERING INFORMATION
MSK5824 K RH G
LEAD CONFIGURATIONS
G=GULL WING
RADIATION HARDENED
SCREENING
BLANK= INDUSTRIAL; H=MIL-PRF-38534 CLASS H;
K=MIL-PRF-38534 CLASS K
GENERAL PART NUMBER
The above example is a Class K regulator with gull wing formed leads.
NOTE: See DSCC SMD 5962F09208 for DSCC part number options.
7
8548-58 Rev. H 6/14
REVISION HISTORY
M.S. Kennedy Corp.
Phone (315) 701-6751
FAX (315) 701-6752
www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make
changes to its products or specifications without notice, however, and assumes no liability for the use of its products.
Please visit our website for the most recent revision of this datasheet.
8
8548-58 Rev. H 6/14