DATASHEET ULTRACAPACITOR CELL INTEGRATION KIT FEATURES AND BENEFITS Simple design and assembly Maximize system lifetime by protecting individual cell against over voltage during rated system use Compatible with BCAP3000, 2000, 1500, 1200 and 650 TYPICAL APPLICATIONS Fast prototyping Application specific modules PRODUCT SPECIFICATIONS ELECTRICAL Turn-on threshold (VOn) Turn-off threshold On-state current Off-state current Allowable operating voltage range Balancing resistor value BKIT-MCINT BKIT-MCIHT 2.6 ± .05 V (VOn- 0.03) to (VOn- 0.1) V 225 ± 25 mA <60 uA -1.0 V to 3.0 V - 49.9 Ω -40°C to +65°C -40°C to +85°C -40°C to +65°C -40°C to +85°C 0% to 90% 0% to 70% 0% to 90% 0% to 70% ENVIRONMENT Operating Temperature Range Storage Temperature Range Humidity Non-condensing at +25°C Non-condensing at +50°C Page 1 Document number: 1006286.7 maxwell.com DATASHEET ULTRACAPACITOR CELL INTEGRATION KIT INCLUDED IN INTEGRATION KIT PACKAGE 3 x Rivets (AD41-43ABS, 1100 Aluminum) 3 x PCBA (93.4 x 38.1mm) + Rivets 5 x Buss Bars (31.8 x 94.8 x 3.2mm, 6061 Aluminum) 12 x Washers (M12 DIN137B Steel) 12 x Retaining Nuts (M12-1.75 x 6mm Steel) ORDERING INFORMATION Integration Kit with active PCBA: BKIT-MCINT (Part number 106927) Integration Kit with passive PCBA: BKIT-MCIHT (Part number 108320) MOUNTING RECOMMENDATIONS For complete assembly instructions please refer to the Integration Kit User Manual (document number 1011158). Torque each connection to 12 ± 2 Nm. Maxwell Technologies cell balance boards are designed to limit any over voltage of the individual capacitors during proper rated system use. The circuit is capable of sinking up to 250mA of current to reduce over voltage on cells. When cells are balanced, the circuit draws less than 60μA (approximately 1% of the typical leakage current of a 3000 F cell), so there is no need to externally control the circuit. Bus Bar Drawing *Refer to user manual for product variant details. Product dimensions are in millimeters and for reference only unless otherwise identified. Product dimensions and specifications may change without notice. Please contact Maxwell Technologies directly for any technical specifications critical to application. All products featured on this datasheet are covered by the following U.S. patents and their respective foreign counterparts: 6643119, 7295423, 7342770, 7352558, 7384433, 7440258, 7492571, 7508651, 7791860, 7791861, 7816891, 7859826, 7883553, 7935155, 8072734, 8098481, 8279580, and patents pending. Maxwell Technologies, Inc. Global Headquarters 3888 Calle Fortunada San Diego, CA 92123 USA Tel: +1 858 503 3300 Fax: +1 858 503 3301 Maxwell Technologies SA Route de Montena 65 CH-1728 Rossens Switzerland Tel: +41 (0)26 411 85 00 Fax: +41 (0)26 411 85 05 Maxwell Technologies, GmbH Leopoldstrasse 244 80807 München Germany Tel: +49 (0)89 / 4161403 0 Fax: +49 (0)89 / 4161403 99 MAXWELL TECHNOLOGIES, MAXWELL, MAXWELL CERTIFIED INTEGRATOR, ENABLING ENERGY’S FUTURE, BOOSTCAP, C CELL, D CELL and their respective designs and/or logos are either trademarks or registered trademarks of Maxwell Technologies, Inc. and may not be copied, imitated or used, in whole or in part, without the prior written permission from Maxwell Technologies, Inc. All contents copyright © 2013 Maxwell Technologies, Inc. All rights reserved. No portion of these materials may be reproduced in any form, or by any means, without prior written permission from Maxwell Technologies, Inc. Page 2 Document number: 1006286.7 maxwell.com Maxwell Technologies, Inc. Shanghai Trading Co. Ltd. Unit A2BC, 12th Floor Huarun Times Square 500 Zhangyang Road, Pudong Shanghai 200122, P.R. China Tel: +86 21 3852 4000 Fax: +86 21 3852 4099