DATA SHEET CLL130-0101A5-27AM1B1

DATA SHEET
CLL130-0101A5-27AM1B1
and
are trademarks or registered trademarks of CITIZEN HOLDINGS CO., LTD. JAPAN.
is a trademark or a registered trademark of CITIZEN ELECTRONICS CO., LTD. JAPAN.
Ref.CE-P2159 09/12
DATA SHEET
1/13
1. Scope of Application
These data sheet are applied to the chip type LED lamp , model CLL130-0101A5-27AM1B1
2. Part code
CLL130-0101A5-27AM1B1
[1]
[2]
[3]
[4]
[5] [6] [7]
[1]Series
CLL : LED for general lighting
[2]Outline dimensions
130 : 2.0(L) x 1.6(W) x 0.75(H)
[3]Dies in series quantity
01 :
1
[4]Dies in parallel quantity
01 :
1
[5]Correlated color temperature
27 : 2700K
[6]Chromaticity range
A : ANSI C78,377-2008
[7]CRI
M1 : Ra Min 80 Type
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
2/13
3. Outline drawing
Unit ：mm
Tolerance ：±0.1mm
4. Performance
( 1 ) Absolute Maximum Rating
Parameter
Symbol
Raiting Value
Unit
Power Dissipation
PD
292
mW
Forward Current
IF
85
mA
Forward Pulse Current
IFP
100
mA
Minimum current
IF min
5
mA
Reverse Current
IR
1
mA
Operating Temperature
TOP
-30 ～ +85
C
Storage Temperature
TST
-40 ～ +100
C
120
C
Junction Temperature
Tj
Max
*1
*2
*1 Forward Current : Duty<=1/10 , Pulse Width<=10msec
*2 D.C. Current : Tj = Ts + Rj-s × PD
Pulse Current : Tj = Ts + Rj-s × Pw(Power Dissipation / One-Pulse) × Duty
*Ts : Solder terminal(Anode)temperature
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
( 2 ) Electro-optical Characteristics
Symbol Condition
Parameter
IF=50mA
Forward Voltage
VF
Thermal Resistance Rj-s *1 Junction-solder
IF=50mA
Luminous Flux
Φv
General Color Rendering Index
IF=50mA
Ra
Min.
2.65
13.4
80
3/13
Typ.
2.95
45
16.8
-
Tｓ=25C
Unit
V
C/W
lm
-
Max.
3.25
20.2
-
*1 Thermal Resistance : Junction - Solder terminal (Anode)
Ranking (Condition : IF=50mA , Ts=25C)
Parameter
Symbol
Forward Voltage
VF
Luminous Flux
ΦV
Rank
Q
R
S
C
D
Min.
2.65
2.85
3.05
13.4
16.8
Max.
2.85
3.05
3.25
16.8
20.2
0
0
x
0.4813
0.4688
0.4585
0.4703
0.4813
x
0.4703
0.4585
0.4483
0.4593
y
0.4319
0.4290
0.4104
0.4132
0.4319
y
0.4132
0.4104
0.3919
0.3944
Unit
V
lm
Chromaticity coordinates ( Condition : IF=50mA ,Ts=25C)
Color Rank
1
Color Rank
3
x
0.4688
0.4562
0.4468
0.4585
0.4688
x
0.4585
0.4468
0.4373
0.4483
y
0.4290
0.4260
0.4077
0.4104
0.4290
y
0.4104
0.4077
0.3893
0.3919
Color Rank
2
Color Rank
4
*1 The tolerance of measurement at our tester is VF±3% , ΦV±7% , Chromaticity(x,y)±0.01
*For an order, products within the rank listed above will be delivered.
Except designation of a delivery proportion of each rank.
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
4/13
x, y Chromaticity
0.44
0.43
0.42
2
y
1
0.41
0.40
3
4
0.39
0.38
0.43
0.44
0.45
0.46
0.47
0.48
0.49
x
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
5/13
5. Characteristics
・Forward Current vs. Forward Voltage
・Forward Current vs. Relative Luminous Intensity
Ts=25C
3.1
VF [V]
3.0
2.9
2.8
2.7
2.6
2.5
2.4
0
20
40
60
IF [mA]
80
120%
100%
80%
60%
40%
20%
0%
20
40
60
IF [mA]
80
100
・Solder Temperature vs. Chromaticity Coordinate
IF =50mA
0.020
0.015
⊿x
0.015
⊿x
0.010
⊿y
0.010
⊿y
0.005
⊿x,⊿y
⊿x,⊿y
140%
0
Ts=25C
0.020
160%
100
・Forward Current vs. Chromaticity Coordinate
Ts=25C
180%
Relative Luminous Intensity
[a.u.]
3.2
0.000
-0.005
0.005
0.000
-0.005
-0.010
-0.010
-0.015
-0.015
-0.020
-0.020
0
20
40
60
IF [mA]
80
100
・Solder Temperature vs. Forward Voltage
Relative Luminous Intensity
[a.u.]
3.0
2.9
2.8
2.7
2.6
0
20
40
60
80
20
40
60
Ts [C]
80
100
・Solder Temperature vs. Relative Luminous Intensity
IF =50mA
3.1
VF [V]
0
100
IF =50mA
120%
100%
80%
60%
40%
20%
0%
0
Ts [C]
20
40
60
Ts [C]
80
100
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
6/13
90
80
70
60
50
40
30
20
10
0
・Spectrum
Relative Emission Intensity
[a.u.]
IF [ｍA]
・Solder Temperature vs. Allowable Forward Current
0
25
50
75
100
125
IF =50mA, Ts=25C
120%
100%
80%
60%
40%
20%
0%
350
150
450
550
650
750
850
λ [nm]
Ts [C]
・Directive Characteristic
IF=50mA Ts=25℃
-40°
-30°
-50°
-20° -10°
100%
10° 20°
30°
40°
50°
80%
θ=0
θ
60°
-60°
60%
-70°
40%
-80°
20%
80°
-90°
0%
90°
70°
IF=50mA Ts=25℃
-40°
-50°
-30°
-20° -10°
100%
10° 20°
30°
40°
50°
80%
θ=0
-60°
60%
60°
-70°
40%
70°
-80°
20%
80°
-90°
0%
90°
θ
LED chip is mounted on White color PCB.
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
7/13
6. Reliability
(1) Details of the tests
Test Item
Continuous Operation Test
Test Condition
Ta=60C, IF=50mA , 1000 hours(with Al-fin)
Ta=85C, IF=50mA , 1000 hours(with Al-fin)
Low Temperature Storage Test
Ta=-40C , 1000 hours
High Temperature Storage Test
Ta=100C, 1000 hours
Moisture-proof Test
Ta=60C, 90%RH, 1000 hours
Thermal Shock Test
Ta=-40C 30minutes～100C 30minuets, 100cycle
(2) Judgment Criteria of Failure for Reliability Test
Ta=25C
Symbol Measuring Condition Judgment Criteria for Failure
Measuring Item
IF=50mA
VF
Forward Voltage
> U×1.2
IF=50mA
Luminous Flux
< S×0.7
Φv
U defines the upper limit of the specified characteristics. S defines the initial value.
Note : Measurement shall be taken between 2 hours and 24 hours, and the test pieces should be
return to the normal ambient conditions after the completion of each test.
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
8/13
7. Taping Specifications (in accordance with JIS standard)
(1) Shape and Dimensions of Reel
21 ±0.8
(Unit: mm)
13 ±0.5
+1
0
0
3
60
180 -
2 ±0.5
Name.
Qty
Lot No.
9 ±0.3
11.4 ±1.0
(Unit: mm)
3 .5 0 ±0 .0 5
1.5-+0.1
0
(2 .2 4 )
(1)
8 ±0 .2
1 .7 5 ±0 .1
(2) Dimensions of Tape
(2)
(1)
(0.9)
2 ±0.05
(1.84)
0.25 ±0.05
(
1.0)
(2)
Polarity
4 ±0.1
4 ±0.1
Progressive direction
(3) Configuration of Tape
(END)
more than 40mm Mounted with CITILED
(START)
Leading part more than 400mm
Unloaded tape
(4) Quantity: 2500pcs/reel
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
9/13
8. Packing Specifications
8-1. Moisture-proof Packing
To prevent moisture absorption during transportation and storage, reels are packed in
aluminum envelopes which contain a desiccant.
Aluminum envelop
Reel
Desiccant
Polyester Zip fastener
Label
8-2. Storage
To prevent moisture absorption, it is strongly recommended that reels (in bulk or
taped) should be stored in the dry box (or the desiccator) with a desiccant as the
appropriate storage place. If not, the following is recommended.
Temperature :
Humidity :
5~30C
60%RH max.
The devices should be mounted as soon as possible after unpacking. If you store the
unpacked reels, please store them in the dry box or seal them into the envelop again.
Moisture Sensitive Level 1. (IPC/JEDEC J-STD-020C)
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
10/13
9. Precautions
9-1. Soldering
(1) Lead free soldering
1) Following soldering paste is recommended
Melting temperature : 216 ~ 220C.
Composition : Sn 3.5Ag 0.75Cu
2) The temperature profile at the top surface of the parts is recommended as shown
below.
T e m p e ra tu re
3) It is requested that products should be handled after their temperature has dropped
down to the normal room temperature
4 °C/sec. Max
4 °C/sec. Max
220 °C
160 ~ 180 °C
140sec
260°C Max
3sec. Max
60 ~ 70sec
Time
9-2. Washing
(1) When washing after soldering is needed, following conditions are requested.
a) Washing solvent: Pure Water
b) Temperature, time: 50C or less × 30 seconds max or 30C or less × 3 minutes max.
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
11/13
9-3. Eye Safety
- The International Electrical Commission (IEC) published in 2006 IEC 62471
”2006 Photobiological safety oflamps and lamp systems ” which includes LEDs within its scope.
When sorting single LEDs according to IEC 62471, most LEDs can be classified as belonging to
either Exempt Group or Risk Group 1.
- Optical characteristics of LEDs such as radiant flux, spectrum and light distribution are factors
that affect the risk group determination of the LED, and especially a high-power LED,
that emits light containing blue wavelengths, may have properties equivalent to those of Risk Group 2.
- Great care should be taken when directly viewing an LED that is driven at high current,
has multiple uses as a module or when focusing the light with optical instruments,
as these actions may greatly increase the hazard to your eyes.
- In addition, LED sources that were included within the scope of IEC 60825-1 /
Edition 1.2 “laser safety standard”, published 2001 were removed from the scope of
the IEC 60825-1 / Edition 2.0 revised 2007.
- However, keep in mind that some countries and regions have adopted standards based
on the IEC laser safety standard IEC 60825-1:2001 which includes LEDs within its scope.
9-4. Other directions
(1) It is requested to avoid any stress added to the resin portion while it is heated.
(2) It is requested to avoid any friction by sharp metal nail etc. to the resin portion.
(3) If the product might to be used under the following conditions, the customer must evaluate
its appropriateness them. This product is not designed for use under the following conditions.
in places where the product might:
- get wet due to rain
- suffer from damage caused by salt.
- be exposed to corrosive gas such as Cl, H2S, NH3, SO2, NOx and so on.
- be exposed to dust, fluid or oil.
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
12/13
10. Designing precautions
1. The current limiting resistor should be placed in the circuit so that is driven within its
rating. Also avoid reverse voltage (over-current) applied instantaneously when ON or OFF.
2. When pulse driving current is applied, average current consumption should be within the
rating. Also avoid reverse voltage applied when put off.
3. Recommended soldering pattern
< For reflow soldering >
Anode Pad
Outline
Center
Cathode Pad
Unit : mm
Mountability and solderability need to be optimized with actual conditions
such as amount of solder, reflow temperature applied in the process.
4. When assembling the circuit board into the finished products, care must be taken to avoid
the component parts from touching other parts.
5. When using multiple LEDs, it is required to connect a current limiting resistor on
each path which the current flows to the LEDs.
(ex-1)
(ex-2)
(ex-3)
R
R
R
R
R
R
R
6. Other
This product complies with RoHS directives.
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12
DATA SHEET
13/13
11. Precautions with regard to product use
1. This document is provided for reference purposes only so that CITIZEN ELECTRONICS'
products are used as intended. CITIZEN ELECTRONICS neither makes warranties or
representations with respect to the accuracy or completeness of the information contained
in this document nor grants any license to any intellectual property rights or any any other
rights of CITIZEN ELECTRONICS or any third party with respect to the information
in this document.
2. All information included in this document such as product data, diagrams, charts,
is current as of the date this document is issued.
Such information, however, is subject to change without any prior notice.
Before purchasing or using any CITIZEN ELECTRONICS' products listed in this document,
please confirm the latest product information with a CITIZEN ELECTRONICS' sales office,
and formal specifications must be exchanged and signed by both parties prior to mass production.
3. CITIZEN ELECTRONICS has used reasonable care in compiling the information
included in this document,
but CITIZEN ELECTRONICS assumes no liability whatsoever for any damages incurred as
a result of errors or omissions in the information included in this document.
4. Absent ａ written signed agreement, except as provided in the relevant terms and conditions of
sale for product, and to the maximum extent allowable by law, CITIZEN ELECTRONICS
assumes no liability whatsoever, including without limitation, indirect, consequential, special,
or incidental damages or loss, including without limitation, loss of profits, loss of opportunities,
business interruption and loss of data, and disclaims any and all express or implied warranties
and conditions related to sale, use of product, or information, including warranties
or conditions of merchantability, fitness for a particular purpose, accuracy of information,
or no infringement.
5. Though CITIZEN ELECTRONICS works continually to improve products' quality and reliability,
products can malfunction or fail. Customers are responsible for complying with safety standards
and for providing adequate designs and safeguards to minimize risk and avoid situations
in which a malfunction or failure of a product could cause loss of human life,
bodily injury or damage to property, including data loss or corruption.
In addition, customers are also responsible for determining the appropriateness of
use of any information contained in this document such as application cases not only with
evaluating by their own but also by the entire system.
CITIZEN ELECTRONICS assumes no liability for customers' product design or applications.
6. Please contact CITIZEN ELECTRONICS' sales office if you have any questions regarding
the information contained in this document, or if you have any other inquiries.
Symbol
CITILED
Name
CLL130-0101A5-27AM1B1
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P2159 09/12