Optoway SPS-23100WG 1 *********************************************************************************************************************************************************************** SPS-23100WG/SPS-23100BWG/SPS-23100AWG (RoHS Compliant) 10.3 Gb/s / 100 km / 1550 nm Digital Diagnostic SFP+ LC SINGLE-MODE TRANSCEIVER *********************************************************************************************************************************************************************** FEATURES DESCRIPTION l l l l l l l l l l l l l l The SPS-23100WG series single mode transceiver is small form factor pluggable module for bi-directional serial optical data communications such as IEEE 802.3ae 10GBASE-ZR/ZW and 10G Fibre Channel. It is with the SFP+ 20-pin connector to allow hot plug capability. Digital diagnostic functions are available via an I2C. This module is designed for single mode fiber and operates at a nominal wavelength of 1550 nm. A guaranteed minimum optical link budget of 24 dB is offered which can correspond to a link distance of over 100 km (assuming worst case fiber loss of 0.22 dB/km). The transmitter section uses a temperature-stabilized 1550 nm electrical-modulated laser (EML) and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated InGaAs avalanche photo detector preamplifier mounted in an optical header and a limiting post-amplifier IC. Support 9.95 Gbps to 10.5 Gbps Complaint with SFP+ MSA Compliant to IEEE 802.3ae 10GBASE-ZR/ZW SFF-8472 Digital Diagnostic Function Temperature-stabilized 1550 nm EML Transmitter Distance up to 100 km at SM Fiber AC/AC Coupling according to MSA Single +3.3 V Power Supply Low Power Consumption RoHS 6/6 Compliant 0 to 70oC Operating: SPS-23100WG -5 to 85oC Operating: SPS-23100BWG -40 to 85oC Operating: SPS-23100AWG Class 1 Laser International Safety Standard IEC-60825 Compliant APPLICATIONS l 100 km 10G Ethernet l 100 km OC-192 / STM-64 l 100 km 10G Fibre Channel LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. ORDER INFORMATION P/No. SPS-23100WG SPS-23100BWG SPS-23100AWG Bit Rate (Gb/s) 10GBASE Distance (km) Wavelength (nm) Package Temp. (oC) RoHS Compliant 10.3 10.3 10.3 ZR / ZW ZR / ZW ZR / ZW 100 100 100 1550 EML 1550 EML 1550 EML SFP+ with DMI SFP+ with DMI SFP+ with DMI 0 to 70 -5 to 85 -40 to 85 Yes Yes Yes Absolute Maximum Ratings Parameter Storage Temperature Relative Humidity Operating Case Temperature Symbol Tstg RH Topr Power Supply Voltage Receiver Input Optical Power Vcc Mip Min -40 5 0 -5 -40 -0.5 Max 85 85 70 85 85 3.6 -4 Units o C % o C V dBm Notes Non-condensing SPS-23100WG SPS-23100BWG SPS-23100AWG Average power *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 12/1/2010 V2.0 Optoway SPS-23100WG 2 *********************************************************************************************************************************************************************** Recommended Operating Conditions Parameter Power Supply Voltage Operating Case Temperature Relative Humidity Power Supply Current Symbol Vcc Topr Min 3.135 0 -5 -40 5 RH ICC (TX+RX) Typ 3.3 85 330 350 9.95 / 10.3 Data Rate Max 3.465 70 85 85 % 500 650 10.5 Units / Notes V o C / SPS-23100WG o C / SPS-23100BWG o C / SPS-23100AWG Non-condensing mA / SPS-2380WG mA / SPS-2380A(B)WG Gb/s Transmitter Optical Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3.47V) Parameter Average Launch Power Output Center Wavelength Output Spectrum Width Side Mode Suppression Ratio Extinction Ratio Relative Intensity Noise Transmitter and Dispersion Penalty Average Launch Power of OFF Transmitter Symbol Po, Avg λc σλ SMSR ER RIN TDP Min 1 1530 Typ 1550 Max +5 1565 1 Units dBm nm nm dB -130 3 dB/Hz dB -30 dBm 30 8.2 Notes 1 -20 dB width 1. Output power is power coupled into a 9/125 µm single-mode fiber. Receiver Optical Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3.47V) Parameter Sensitivity in Average Power Receiver Overload LOS -- Deasserted LOS -- Asserted Wavelength of Operation Symbol Sen1 PMAX LOSD LOSA λc Min Typ -8 ---35 1530 ------- Max -23 -27 --1565 Units dBm dBm dBm dBm nm Typ Max Units 9.95 / 10.3 100 10.5 Notes 2 Transition: low to high Transition: high to low 2. Measured with average power; BER < 10-12 and PRBS 231-1 at 10.3125 Gb/s.. Electrical Characteristics Parameter Symbol High-Speed Signal (CML) Interface Specification Input Data Rate Differential Input Impedance Rin Differential Data Input Amplitude Output Data Rate Differential Output Impedance Rout Differential Data Output Amplitude Low-Speed Signal (LVTTL) Interface Specification Input High Voltage Input Low Voltage Output High Voltage Output Low Voltage Min 340 850 Gb/s Ω mVpp Gb/s Ω mVpp 2.0 GND 2.4 GND Vcc+0.3 0.8 Vcc 0.5 V V V V 120 9.95 / 10.3 100 820 10.5 Notes Internally AC coupled Internally AC coupled ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 12/1/2010 V2.0 Optoway SPS-23100WG 3 *********************************************************************************************************************************************************************** CONNECTION DIAGRAM PIN Signal Name 1 2 VEET TX_Fault 3 TX_Disable 4 SDA 5 SDL 6 7 MOD-ABS RS0 8 9 RX_LOS RS1 10 VEER Description PIN Signal Name Transmitter Signal Ground Transmitter Fault Indication. Logic “1” Output = Laser Fault. Logic “0” Output = Normal Operation Logic “1” Input (or no connection) = Laser off, Logic “0” = Laser on. Modulation Definition 2 – Two wires serial ID Interface Modulation Definition 1 – Two wires serial ID Interface Modulation Definition 0 – Ground in Module RX Rate Select (LVTTL). This pin has an internal 30k pulldown to ground. A signal on this pin will not affect module performance. Loss of Signal Out (OC). TX Rate Select (LVTTL). This pin has an internal 30k pulldown to ground. A signal on this pin will not affect module performance. Receiver Signal Ground Description 11 12 VEER RD- Receiver Signal Ground Inverse Receiver Data Out 13 RD+ Receiver Data Out 14 VEER Receiver Signal Ground 15 VCCR Receiver Power – 3.3V±5% 16 17 VCCT VEET Transmitter Power – 3.3V±5% Transmitter Signal Ground 18 19 TD+ TD- Transmitter Data In Inverse Transmitter Data In 20 VEET Transmitter Signal Ground MODULE DEFINITION Module Definition PIN 4 PIN 5 PIN 6 Interpretation by Host 4 SDA SCL MOD-ABS Serial module definition protocol Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, SDA and SDL appear as no connector (NC) and MOD-ABS is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E2PROM protocol of the ATMEL AT24C01A/02/04 family of components. ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 12/1/2010 V2.0 Optoway SPS-23100WG 4 *********************************************************************************************************************************************************************** RECOMMENDED CIRCUIT SCHEMATIC Vee T Tx_DISABLE Tx_FAULT (1,17,20) 3 Tx_DISABLE 2 Tx_FAULT 10 KΩ TD + LD Driver 18 TD + Z=50Ω 100Ω TD - 19 TD Z=50Ω Vcc T 4 .7 μH 16 Vcc 3.3V 0.1μF 22 μF 0.1μF SerDes IC 0.1μF Vcc R 15 0.1μF RD - 22 μF 4 .7 μH 12 Protocol IC RD Z=50Ω 100Ω POST Amp RD + 13 RD + Z=50Ω depending on SERDES 10 KΩ LOS Vee R 30KΩ 8 RS1 9 RS0 7 30KΩ MOD_ABS EEPROM SCL SDA LOSS OF SINGAL (10,11,14) TX Rate Select RX Rate Select 6 MODULE DETECT 5 SCL 4 SDA 10 KΩ SFP+ module 10 KΩ 10 KΩ Vcc 3.3V PACKAGE DIAGRAM Units in mm Note: Specifications subject to change without notice. ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 12/1/2010 V2.0 Optoway SPS-23100WG 5 *********************************************************************************************************************************************************************** REVISION HISTORY Version 1.0 2.0 Subject Release Date Initial datasheet 1) Add SPS-23100BWG for extended temperature version 2) Add SPS-23100AWG for industrial temperature version 2010/7/1 2010/12/1 ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 12/1/2010 V2.0