IS Series Ultra Low Profile Power Resistors F e at u r e s •Heatsinkable •Rugged construction •Low profile •Ultra low profile thick•High power film on steel •Pulse handling capability •175W to 270W sizes •Non-flammable •Single fixing heatsink mountable •Low inductances •Available with fast-on terminals or wire leads uses •Braking resistors •In-rush current limiter •Bleeder resistor •Power switching •Soft charging S ERIE S S P ECI F ICATI O N S Power Resistance Rating Range Type (watts) (Ω) IS175 175 5Ω to 10KΩ IS200 200 5Ω to 10KΩ IS250 250 5Ω to 10KΩ IS270 270 5Ω to 10KΩ Construction Tolerance 10%, 20% 10%, 20% 10%, 20% 10%, 20% Dielectric Termination Glass Overcoat Resistive Glaze Stainless Steel characteristics TCR <250ppm (surface temp less than 150°C) Derating Maximum element 365°C temperature Over-voltage rating 5X rated power for up to for up to 1 second Resistive element Thick Film Derating element surface temp. at 100% to 0% power at 200°C surface temp. Power rating dependent on mounting and heatsink thermal capacity % Rated Power Working voltage Not to exceed 300V 120 100 80 60 40 20 0 0 Hot spot surface 200°C max. temperature Pulsed load at full Max. 1%ΔR; (see Fig 1) pulse power rating Mounted on a 0.06°C/W heatsink with 1,000 cycles forced air cooling, air temperature 25°C (ref AH32430 12" long) Solder Silver solder is recommended for IS Series resistors. Leaching of the silver in the termination will occur if non-silver solder is used. 60/40 tin-lead solders are not recommended for use with the IS Series product. Screw torque 3.5 Nm 50 100 150 200 Resistor Surface Temp., oC 250 THIS PRODUCT IS DESIGNED FOR USE WITH PROPER HEATSINKING. Maximum base plate temperature of the resistor must be monitored and kept within specified limits to establish the power rating. Best technique is to attach a thermocouple to the side of the base plate of the resistor. (continued) 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • [email protected] 137 IS Series Ultra Low Profile Power Resistors d i m e ns i ons (in/mm) Thickness: 0.062 in. / 1.57mm ±.1 L Type Wattage L ±0.2mm W ±0.2mm IS175 175 1.94/49.30 1.41/35.90 IS200 200 2.40/61.00 1.60/40.60 IS250 250 4.00/101.60 2.76/70.00 IS270 270 4.80/122.00 2.76/70.00 ØD nom. 0.13/3.20 0.21/5.30 0.21/5.30 0.21/5.30 Wt. nom (oz/g) 0.44/12.60 0.60/17.10 1.78/50.80 2.12/60.70 W D T e r m i n a t i on O p t i ons Solder pad only SnAg (96S) Flying leads Push-on connectors 9mm 0.250" 9mm 10" 14AWG O R D ERI N G I N F O R M ATI O N Tolerance K = 10% RoHS M = 20% Compliant IS200C47RKE Series Wattage Termination Resistance Insulated 175 A = Tinned pad 3 digits Steel 200 B = Soldered lead 47R = 47Ω 250 C = Fast on terminal 270 138 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • [email protected] 0.032"