NVELJ048Z-M3

NICHIA STS-DA1-3721 <Cat.No.150312>
NICHIA CORPORATION
SPECIFICATIONS FOR WARM WHITE LED
NVELJ048Z-M3
● Built-in ESD Protection Device
● RoHS Compliant
NICHIA STS-DA1-3721 <Cat.No.150312>
SPECIFICATIONS
(1) Absolute Maximum Ratings
Symbol
Absolute Maximum Rating
Unit
Forward Current
Item
IF
3300
mA
Pulse Forward Current
IFP
4950
mA
Allowable Reverse Current
IR
85
mA
Power Dissipation
PD
168
W
Operating Temperature
Topr
-40~105
°C
Storage Temperature
Tstg
-40~100
°C
Junction Temperature
TJ
150
°C
* Absolute Maximum Ratings at TC=25°C.
* IFP conditions with pulse width ≤10ms and duty cycle ≤10%.
* The operating Temperature (Topr) range is the range of case temperatures.
(2) Initial Electrical/Optical Characteristics
Item
Symbol
Condition
Typ
Max
Unit
Forward Voltage
VF
IF=1800mA
47.2
-
V
Luminous Flux
Φv
IF=1800mA
5120
-
lm
-
IF=1800mA
0.4338
-
-
-
IF=1800mA
0.4030
-
-
RθJC
-
0.40
0.44
°C/W
Chromaticity Coordinate
Thermal Resistance
x
y
* Characteristics at TC=25°C.
* Luminous Flux value as per CIE 127:2007 standard.
* Chromaticity Coordinates as per CIE 1931 Chromaticity Chart.
* RθJC is Thermal Resistance from junction to TC measuring point.
1
NICHIA STS-DA1-3721 <Cat.No.150312>
RANKS
Item
Rank
Forward Voltage
Luminous Flux
Min
Max
Unit
V
-
43.4
51.0
Q0558
5580
6840
Q0524
5240
6420
Q0495
4950
6050
Q0460
4600
5640
Q0435
4350
5330
lm
Color Ranks
Center Point
Rank sm273
Rank sm303
Rank sm353
Rank sm403
Rank sm453
x
0.4578
0.4338
0.4073
0.3818
0.3611
y
0.4101
0.4030
0.3917
0.3797
0.3658
* Ranking at TC=25°C.
* Forward Voltage Tolerance: ±0.46V
* Luminous Flux Tolerance: ±7%
* Chromaticity Coordinate Tolerance: ±0.005
* The color rank has a chromaticity range within a 3-step MacAdam ellipse.
* LEDs from the above ranks will be shipped.
The rank combination ratio per shipment will be decided by Nichia.
Luminous Flux Ranks by Color Rank
Ranking by
Luminous Flux
Ranking by
Q0435
Q0460
Q0495
Q0524
Q0558
Color Coordinates
sm273
sm303
sm353
sm403
sm453
2
NICHIA STS-DA1-3721 <Cat.No.150312>
CHROMATICITY DIAGRAM
0.50
0.45
sm273
sm303
sm353
y
0.40
黒体放射軌跡
Blackbody Locus
sm403
sm453
0.35
3000K
2700K
3500K
4000K
4500K
0.30
0.25
0.30
0.35
0.40
0.45
0.50
0.55
x
3
NICHIA STS-DA1-3721 <Cat.No.150312>
OUTLINE DIMENSIONS
* 本製品はRoHS指令に適合しております。
This product complies with RoHS Directive.
* 括弧で囲まれた寸法は参考値です。
The dimension(s) in parentheses are for reference purposes.
管理番号 No.
NVExJ048x
STS-DA7-7290A
(単位 Unit:±0.3)
mm)
(単位 Unit: mm, 公差 Tolerance:
発光部中心の位置精度 ±0.3mm
The center of emitting area to be centered ±0.3mm.
22
Cathode
19
(14.6)
Anode
(16.6)
24
項目 Item
内容 Description
パッケージ材質
Package Materials
電極材質
Electrodes Materials
セラミックス
Ceramics
シリコーン樹脂
（拡散剤+蛍光体入り）
Silicone Resin
(with diffuser and phosphor)
金メッキ
Au-plated
質量
Weight
1.8g(TYP)
封止樹脂材質
Encapsulating Resin
Materials
A
K
保護素子
Protection Device
4
NICHIA STS-DA1-3721 <Cat.No.150312>
SOLDERING
• Recommended Hand Soldering Condition
Temperature
380°C Max
Soldering Time
5sec Max
* Hand soldering must not be performed more than once.
* Since the silicone used in the encapsulating resin frame is soft, do not press on the encapsulating resin frame or resin area.
Pressure can cause nicks, chip-outs, encapsulant delamination and deformation, and wire breaks, decreasing reliability.
* Repairing should not be done after the LEDs have been soldered.
It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
* When soldering, do not apply stress to the LED while the LED is hot.
* When using a pick and place machine, choose an appropriate nozzle for this product. Using a pick-and-place nozzle
with a smaller diameter than the size of the LED's emitting surface will cause damage to the emitting surface
and may also cause the LED not to illuminate.
* When flux is used, it should be a halogen free flux. Ensure that the manufacturing process is not designed in a manner
where the flux will come in contact with the LEDs.
* During and/or after soldering an electric wire to the electrode, ensure that tension is not applied to the electric wire.
This may cause the electrode to be damaged and/or reduce the adhesive strength of the electrode to the package.
* If soldering is used to join electric wires to the electrodes, the adhesive strength of the electrode to the package
may be reduced depending on the substances that are found in the solder paste and/or the type of the wire cover that is used.
Ensure that there are no issues with the materials that will be used in the chosen application prior to use.
5
NICHIA STS-DA1-3721 <Cat.No.150312>
TRAY DIMENSIONS
6
NICHIA STS-DA1-3721 <Cat.No.150312>
PACKAGING - TRAY PACK
7
NICHIA STS-DA1-3721 <Cat.No.150312>
LOT NUMBERING CODE
Lot Number is presented by using the following alphanumeric code.
YMxxxx - RRR
Y - Year
Year
Y
2014
E
2015
F
2016
G
2017
H
2018
I
2019
J
M - Month
Month
M
Month
M
1
1
7
7
2
2
8
8
3
3
9
9
4
4
10
A
5
5
11
B
6
6
12
C
xxxx-Nichia's Product Number
RRR-Ranking by Color Coordinates, Ranking by Luminous Flux
8
NICHIA STS-DA1-3721 <Cat.No.150312>
DERATING CHARACTERISTICS
NVExJ048Z-Mx
管理番号 No. STS-DA7-7756
ケース温度測定部温度-許容順電流特性
Temperature at Measure Point on
a Case vs
Derating1
Allowable Forward Current
許容順電流
Allowable Forward Current(mA)
5000
4000
(78, 3300)
3000
2000
(105, 2080)
1000
0
0
20
40
60
80
100
120
ケース温度測定部温度
Temperature at Measure Point on a Case(°C)
デューティー比-許容順電流特性
Duty Ratio vs
Duty
Allowable Forward Current
10000
T A =25°C
許容順電流
Allowable Forward Current(mA)
4950
3300
1000
100
1
10
100
デューティー比
Duty Ratio(%)
9
NICHIA STS-DA1-3721 <Cat.No.150312>
OPTICAL CHARACTERISTICS
NVELJ048Z-M3
管理番号 No. STS-DA7-7743
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
発光スペクトル
Spectrum
TA =25°C
IFP=1800mA
Spectrum
1.0
相対発光強度
Relative Emission Intensity(a.u.)
0.8
0.6
0.4
0.2
0.0
400
450
500
550
600
650
700
750
800
波長
Wavelength(nm)
Directivity1
指向特性
Directivity
-20°
-10°
0°
TA =25°C
IFP=1800mA
10°
20°
-30°
30°
-40°
40°
放射角度
Radiation Angle
-50°
50°
-60°
60°
-70°
70°
80°
-80°
-90°
90°
1
0.5
0
0.5
1
相対照度
Relative Illuminance(a.u.)
10
NICHIA STS-DA1-3721 <Cat.No.150312>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
NVELJ048Z-M3
管理番号 No. STS-DA7-7744
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電圧-順電流特性
Forward Voltage vs
Forward Current
周囲温度-順電圧特性
Ambient Temperature vs
Forward Voltage
VfIf
TA =25°C
10000
IFP=1800mA
60
4950
55
順電圧
Forward Voltage(V)
順電流
Forward Current(mA)
TaVf
1800
1000
50
45
40
100
35
35
40
45
50
55
60
-60 -40 -20
順電圧
Forward Voltage(V)
順電流-相対光束特性
Forward Current vs
Relative Luminous Flux
TA =25°C
周囲温度-相対光束特性
Ambient Temperature vs
Relative Luminous Flux
40
60
80
100 120
相対光束
Relative Luminous Flux(a.u.)
2.0
1.5
1.0
TaIv
IFP=1800mA
1.4
2.5
相対光束
Relative Luminous Flux(a.u.)
20
周囲温度
Ambient Temperature(°C)
IfIv
3.0
0
1.2
1.0
0.8
0.6
0.5
0.0
0.4
0
1000
2000
3000
4000
順電流
Forward Current(mA)
5000
6000
-60 -40 -20
0
20
40
60
80
100 120
周囲温度
Ambient Temperature(°C)
11
NICHIA STS-DA1-3721 <Cat.No.150312>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
NVELJ048Z-M3
管理番号 No. STS-DA7-7745
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電流-色度 特性
Forward Current vs
Chromaticity Coordinate
Ifxy
TA =25°C
0.42
0.41
y
4950mA
1800mA
0.40
100mA
0.39
0.38
0.41
0.42
0.43
0.44
0.45
x
周囲温度-色度 特性
Ambient Temperature vs
Chromaticity Coordinate
Taxy
IFP= 1800mA
0.42
-40˚C
0.41
y
0˚C
25˚C
0.40
105˚C
0.39
0.38
0.41
0.42
0.43
0.44
0.45
x
12
NICHIA STS-DA1-3721 <Cat.No.150312>
RELIABILITY
(1) Tests and Results
Reference
Test
Standard
Temperature Cycle
Duration
JEITA ED-4701
-40°C(30min)~25°C(5min)~
100 105
100°C(30min)~25°C(5min)
High Temperature
JEITA ED-4701
Storage
200 201
Temperature Humidity
JEITA ED-4701
Storage
100 103
Low Temperature
JEITA ED-4701
Storage
200 202
High Temperature
Operating Life
Electrostatic Discharges
Test
Test Conditions
Failure
Criteria
#
Units
Failed/Tested
100cycles
#1
0/10
TA=100°C
1000hours
#1
0/10
TA=60°C, RH=90%
1000hours
#1
0/10
TA=-40°C
1000hours
#1
0/10
TC=78°C, IF=3300mA
1000hours
#1
0/10
#1
0/10
JEITA ED-4701
HBM, 2kV, 1.5kΩ, 100pF, 3pulses,
300 304
alternately positive or negative
NOTES:
Measurements are performed after allowing the LEDs to return to room temperature.
(2) Failure Criteria
Criteria #
#1
Items
Conditions
Failure Criteria
Forward Voltage(VF)
IF=1800mA
>Initial value×1.1
Luminous Flux(ΦV)
IF=1800mA
<Initial value×0.7
13
NICHIA STS-DA1-3721 <Cat.No.150312>
CAUTIONS
(1) Storage
Conditions
Storage
Temperature
Humidity
Time
Before Opening Aluminum Bag
≤30°C
≤90%RH
Within 1 Year from Delivery Date
After Opening Aluminum Bag
≤30°C
≤70%RH
≤168hours
● After opening the moisture-proof aluminum bag, the products should go through the soldering process
within the range of the conditions stated above. Unused remaining LEDs should be stored with silica gel desiccants
in a hermetically sealed container, preferably the original moisture-proof bags for storage.
● Although the leads or electrode pads (anode and cathode) of the product are plated with gold,
prolonged exposure to a corrosive environment might cause the gold plated the leads or electrode pads to tarnish.
If unused LEDs remain, they must be stored in a hermetically sealed container.
Nichia recommends using the original moisture-proof bag for storage.
● Do not use sulfur-containing materials in commercial products. Some materials, such as seals and adhesives, may contain sulfur.
The contaminated plating of LEDs might cause an open circuit. Silicone rubber is recommended as a material for seals.
Bear in mind, the use of silicones may lead to silicone contamination of electrical contacts inside the products,
caused by low molecular weight volatile siloxane.
● To prevent water condensation, please avoid large temperature and humidity fluctuations for the storage conditions.
● Do not store the LEDs in a dusty environment.
● Do not expose the LEDs to direct sunlight and/or an environment where the temperature is higher than
normal room temperature.
(2) Directions for Use
● When designing a circuit, the current through each LED must not exceed the Absolute Maximum Rating.
Operating at a constant current per LED is recommended. In case of operating at a constant voltage, Circuit B is recommended.
If the LEDs are operated with constant voltage using Circuit A, the current through the LEDs may vary due to the variation
in Forward Voltage characteristics of the LEDs.
...
...
● This product should be operated using forward current. Ensure that the product is not subjected to
either forward or reverse voltage while it is not in use. In particular, subjecting it to continuous reverse voltage
may cause migration, which may cause damage to the LED die. When used in displays that are not used for a long time,
the main power supply should be switched off for safety.
● Pulse width modulation (PWM) is recommended for dimming LEDs as color point changes with drive current.
● It is recommended to operate the LEDs at a current greater than 10% of the sorting current to stabilize the LED characteristics.
● Ensure that excessive voltages such as lightning surges are not applied to the LEDs.
● For outdoor use, necessary measures should be taken to prevent water, moisture and salt air damage.
(3) Handling Precautions
● Do not handle the LEDs with bare hands as it will contaminate the LED surface and may affect the optical characteristics:
it might cause the LED to be deformed and/or the wire to break, which will cause the LED not to illuminate.
● When handling the product with tweezers, be careful not to apply excessive force to the resin.
Otherwise, The resin can be cut, chipped, delaminate or deformed, causing wire-bond breaks and catastrophic failures.
● Dropping the product may cause damage.
● Do not stack assembled the products. Failure to comply can cause the resin portion of the product to be cut, chipped,
delaminated and/or deformed. It may cause wire to break, leading to catastrophic failures.
14
NICHIA STS-DA1-3721 <Cat.No.150312>
(4) Design Consideration
● Volatile organic compounds that have been released from materials present around the LEDs (e.g. housing, packing,
adhesive, secondary lens, lens cover, etc.) may penetrate the LED lens and/or encapsulating resin.
If the LEDs are being used in a hermetically sealed environment, these volatile compounds can discolor after being exposed
to heat and/or photon energy and it may greatly reduce the LED light output and/or cause a color shift.
In this case, ventilating the environment may improve the reduction in light output and/or color shift.
Perform a light-up test of the chosen application for optical evaluation to ensure that there are no issues,
especially if the LEDs are planned to be used in a hermetically sealed environment.
● Excessive forces on this product can cause the ceramic package to crack.
It is recommended to use a holder when fixing this product to a chassis.
● It is recommended to use a thermal film or thermal grease between the product and a chassis for increased heat dissipation.
(5) Electrostatic Discharge (ESD)
● The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability.
When handling the products, the following measures against electrostatic discharge are strongly recommended:
Eliminating the charge
Grounded wrist strap, ESD footwear, clothes, and floors
Grounded workstation equipment and tools
ESD table/shelf mat made of conductive materials
● Ensure that tools (e.g. soldering irons), jigs and machines that are being used are properly grounded and
that proper grounding techniques are used in work areas. For devices/equipment that mount the LEDs,
protection against surge voltages should also be used.
● If tools or equipment contain insulating materials such as glass or plastic,
the following measures against electrostatic discharge are strongly recommended:
Dissipating static charge with conductive materials
Preventing charge generation with moisture
Neutralizing the charge with ionizers
(6) Thermal Management
● Proper thermal management is an important when designing products with LEDs. LED die temperature is affected
by LED module thermal resistance and LED spacing. Please design products in a way that the LED die temperature
does not exceed the maximum Junction Temperature (TJ).
● The dice temperature of the products should be calculated, using the case temperature (TC) of the product incorporated
into the end-product, by the following equation.
TJ=TC+RθJC･W
*TJ=LED junction temperature: °C
TC=Case temperature: °C
RθJC=Thermal resistance from junction to TC measuring point: °C/W
W=Input power(IF×VF): W
15
NICHIA STS-DA1-3721 <Cat.No.150312>
(7) Cleaning
● The LEDs should not be cleaned with water, benzine, and/or thinner.
● If required, isopropyl alcohol (IPA) should be used. Other solvents may cause premature failure to the LEDs
due to the damage to the resin portion. The effects of such solvents should be verified prior to use.
In addition, the use of CFCs such as Freon is heavily regulated.
● When dust and/or dirt adheres to the LEDs, soak a cloth with Isopropyl alcohol (IPA), then squeeze it before wiping the LEDs.
● Ultrasonic cleaning is not recommended since it may have adverse effects on the LEDs
depending on the ultrasonic power and how LED is assembled.
If ultrasonic cleaning must be used, the customer is advised to make sure the LEDs will not be damaged prior to cleaning.
(8) Eye Safety
● In 2006, the International Electrical Commission (IEC) published IEC 62471:2006 Photobiological safety of lamps
and lamp systems, which added LEDs in its scope.
On the other hand, the IEC 60825-1:2007 laser safety standard removed LEDs from its scope.
However, please be advised that some countries and regions have adopted standards
based on the IEC laser safety standard IEC 60825-1:20112001, which still includes LEDs in its scope.
Most of Nichia's LEDs can be classified as belonging into either the Exempt Group or Risk Group 1.
High-power LEDs, that emit light containing blue wavelengths, may be classified as Risk Group 2.
Please proceed with caution when viewing directly any LEDs driven at high current, or viewing LEDs
with optical instruments which may greatly increase the damages to your eyes.
● Viewing a flashing light may cause eye discomfort. When incorporating the LED into your product,
please be careful to avoid adverse effects on the human body caused by light stimulation.
(9) Others
● The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment,
communications equipment, measurement instruments and household appliances).
Consult Nichia's sales staff in advance for information on the applications in which exceptional quality
and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or
health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control system, automobiles,
traffic control equipment, life support systems and safety devices).
● The customer shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent
from Nichia. When defective LEDs are found, the customer shall inform Nichia directly before disassembling or analysis.
● The specifications and appearance of this product may change without notice;
Nichia does not guarantee the contents of this specification. Both the customer and Nichia
will agree on the official specifications of supplied products before the volume production of a program begins.
16