Preliminary Datasheet LP28012 1.2A Single-chip Li-ion and Li-POL Charge General Description Features The LP28012 is a complete constant-current/ constant voltage linear charger for single cell lithium-ion batteries. Its ESOP8 package and low external component count make the LP28012 ideally suited for portable applications. No external sense resistor is needed, and no blocking diode is required due to the internal MOSFET architecture. Thermal feedback regulates the charge current to limit the die temperature during high power operation or high ambient temperature. The charge voltage is fixed at 4.2V, and the charge current can be ISET rammed externally with a single resistor. The LP28012 automatically terminates the charge cycle when the charge current drops to 1/10th the ISET rammed value after the final float voltage is reached. When the input supply is removed, the LP28012 automatically enters a low current state, dropping the battery drain current to less than 4µA. Other features include charge current monitor, under voltage lockout, automatic recharge and a status pin to indicate charge termination and the presence of an input voltage. Very Low Power Dissipation Short-circuit protection Programmable Charge Current Up to 1200mA No MOSFET, Sense Resistor or Blocking Diode Required Constant-Current/Constant-Voltage Operation with Thermal Regulation to Maximize Charge Rate Without Risk of Overheating 8µA Supply Current in Shutdown Drainage Charge Current Thermal Regulation Status Outputs for LED or System Interface Indicates Charge and Fault Conditions Consumption Available in TDFN-10 Package RoHS Compliant and 100% Lead (Pb)-Free Typical Application Circuit VIN LP28012 1 8 3 2 Order Information LP28012 10uF 5 BATT 10 1uF STAT2 BATTERY STAT1 GND ISET 6 Rset 2K □ □ □ ICHARG=1000/Rset F: Pb-Free Package Type QV: TDFN-10 Marking Information Device Marking Package Shipping LP28012 LPS QV:TDFN-10 3K/REEL Applications LP28012 Portable Media Players/Game Power Bank PDA/MID Bluetooth Applications LP28012 – 00 VIN EN Feb.-2014 Email: [email protected] XXXX www.lowpowersemi.com Page 1 of 10 Preliminary Datasheet LP28012 Functional Pin Description Package Type Pin Configurations TDFN-10 Pin Description PIN PIN No. 4,7,9 NC DESCRIPTION No Connector. Charge Current Program, Charge Current Monitor and Shutdown Pin. The charge current is programmed by connecting a 1% 6 Iset resistor(RPROG)to ground. When charging in constant-current mode, this pin servos to 1V. In all modes, the voltage on this pin can be used to measure the charge current using the following formula. Iset=1000/Riset. 5,11 GND 1 Vin 10 BATT 3 STAT2 2 STAT1 8 EN LP28012 – 00 VSS is the connection to system ground. VIN is the input power source. Connect to a wall adapter. BAT is the connection to the battery. Typically a 10µF Tantalum capacitor is needed for stability when there is no battery attached. When a battery is attached, only a 0.1µF ceramic capacitor is required. Open-Drain Charge Status Output. When the battery is charging, the STAT pin is pulled High by an internal N-channel MOSFET. When the charge cycle is completed, the pin is pulled Low. Open-Drain Charge Status Output. When the battery is charging, the STAT pin is pulled low by an internal N-channel MOSFET. When the charge cycle is completed, the pin is pulled High. Chip enable pin. Charging when the pin Voltage is floating and high, discharge when the pin in Low voltage. Feb.-2014 Email: [email protected] www.lowpowersemi.com Page 2 of 10 Preliminary Datasheet LP28012 Function Block Diagram 1 VCC 1X 1200X - BAT 5μA + MA 10 R1 CA - + 8 2 CE + VA - R2 SCHMITT SHDN STAT1 C1 - REF 1.22V + R3 1V R4 C2 3 STAT2 C3 LP28012 + 0.1V - R5 + - TO BAT 3μA VCC 2.9V 6 SET GND SET 5 Absolute Maximum Ratings Input Voltage to GND (VIN) ------------------------------------------------------------------------------- 3.9V to 7V BAT, ISET, STAT (VX) -----------------------------------------------------------------------------0.3V to VIN+0.3V BAT Short-Circuit Duration ------------------------------------------------------------------------------ Continuous BAT Pin Current ---------------------------------------------------------------------------------------------- 1200mA Maximum Junction Temperature ------------------------------------------------------------------------------ 125°C Operating Junction Temperature Range (TJ) ----------------------------------------------------- -40℃ to 85°C Maximum Soldering Temperature (at leads, 10 sec) ----------------------------------------------------- 260°C Thermal Information Maximum Power Dissipation (PD,TA<40°C) ----------------------------------------------------------------- 1.5W Thermal Resistance (JA) -----------------------------------------------------------------------------------------46℃/W LP28012 – 00 Feb.-2014 Email: [email protected] www.lowpowersemi.com Page 3 of 10 Preliminary Datasheet LP28012 Electrical Characteristics (The specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = 5V, unless otherwise noted.) SYMBOL VIN ICC PARAMETER CONDITIONS MIN TYP. MAX UNITS 2.65 5 7 V Charge Mode, RISET = 10k 300 2000 Standby Mode (Charge Terminated) 200 500 25 50 4.2 4.242 Adapter/USB Voltage Range Input Supply Current Shutdown Mode (RISET Not Connected, VCC < VBAT, or VCC < VUV) VFLOAT IBAT ITRIKL Regulated Output (Float) Voltage BAT Pin Current 0°C ≤ TA ≤ 85°C, IBAT = 40mA 4.158 RISET = 1k, Current Mode 1000 RISET = 2k, Current Mode 500 Standby Mode, VBAT = 4.2V Shutdown Trickle Charge Current 0 -2.5 -6 ±1 ±2 Sleep Mode, VCC = 0V VBAT < VTRIKL, RISET = 2k ±1 60 ±2 2.9 3.0 VTRIKL Trickle Charge Threshold Voltage RISET = 10k, VBAT Rising Trickle Charge Hysteresis Voltage RISET = 10k 120 VUV VCC Under voltage Lockout Threshold From VCC Low to High 3.9 VUVHYS VCC Under voltage Lockout Hysteresis VMSD VASD ITERM Manual Shutdown Threshold Voltage VCC – VBAT Lockout Threshold Voltage C/10 Termination Current Threshold 2.8 150 200 V mA Mode (RISET Not Connected) VTRHYS uA uA mA V mV V 300 mV ISET Pin Rising 2 V ISET Pin Falling 2.2 V VCC from Low to High 70 100 140 mV VCC from High to Low 5 30 50 mV RISET = 10k 0.085 0.10 0.115 mA/mA RISET = 2k 0.085 0.10 0.115 mA/mA VISET ISET Pin Voltage RISET = 10k, Current Mode 2 V ISTAT STAT Pin Weak Pull-Down Current VSTAT = 5V 5 uA VSTAT STAT Pin Output Low Voltage ISTAT = 5mA Recharge Battery Threshold Voltage VFLOAT - VRESTAT ΔVRESTAT 100 0.35 0.6 V 150 200 mV TLIM Junction Temperature in Constant Temperature Mode 120 °C RON Power FET “ON” Resistance (Between VCC and BAT) 600 mΩ Tss Soft-Start Time 100 uS 150 uA IISET LP28012 – 00 IBAT = 0 to IBAT =850V/RISET ISET Pin Pull-Up Current Feb.-2014 Email: [email protected] www.lowpowersemi.com Page 4 of 10 Preliminary Datasheet LP28012 – 00 Feb.-2014 Email: [email protected] www.lowpowersemi.com LP28012 Page 5 of 10 Preliminary Datasheet LP28012 Application Information The LP28012 is a single cell lithium-ion battery charger using a constant-current/constant-voltage algorithm. It can deliver up to 1200mA of charge current (using a good thermal PCB layout) with a final float voltage accuracy of ±1%. The LP28012 includes an internal P-channel power MOSFET and thermal regulation circuitry. No blocking diode or external current sense resistor is required; thus, the basic charger circuit requires only Charge Termination A charge cycle is terminated when the charge current falls to 1/10th the ISET rammed value after the final float voltage is reached. This condition is detected by using an internal, filtered comparator to monitor the ISET pin. When the ISET pin voltage falls below 100mV 1 for longer than tTERM (typically 1ms), two external components. Furthermore, the LP28012 is capable charging is terminated. The charge current is latched off and the of operating from a USB power source. LP28012 enters standby mode, where the input supply current drops to 200µA. (Note: C/10 termination is disabled in trickle Normal Charge Cycle charging and thermal limiting modes). A charge cycle begins when the voltage at the VCC pin rises When charging, transient loads on the BAT pin can cause the above the UVLO threshold level and a 1% ISET ram resistor is connected from the ISET pin to ground or when a battery is ISET pin to fall below 200mV for short periods of time before the DC charge current has dropped to 1/10th the ISET rammed connected to the charger output. If the BAT pin is less than 2.9V, value. The 1ms filter time (tTERM) on the termination comparator the charger enters trickle charge mode. In this mode, the ensures that transient loads of this nature do not result in LP28012 supplies approximately 1/10 the ISET rammed charge premature charge cycle termination. Once the average charge current to bring the battery voltage up to a safe level for full current drops below 1/10th the ISET rammed value, the current charging. (Note: The LP28012 does not include this LP28012 terminates the charge cycle and ceases to provide trickle charge feature). any current through the BAT pin. In this state, all loads on the When the BAT pin voltage rises above 2.9V, the charger enters BAT pin must be supplied by the battery. constant-current mode, where the ISET rammed charge current The LP28012 constantly monitors the BAT pin voltage in is supplied to the battery. When the BAT pin approaches the standby mode. If this voltage drops below the 4.05V recharge final float voltage (4.2V), the LP28012 enters constant-voltage threshold (VRESTAT), another charge cycle begins and current is mode and the charge current begins to decrease. When the once again supplied to the battery. To manually restart a charge charge current drops to 1/10 of the ISET rammed value, the cycle when in standby mode, the input voltage must be charge cycle ends. removed and reapplied, or the charger must be shut down and restarted using the ISET pin. Figure 1 shows the state diagram of a typical charge cycle. ISET ramming Charge Current The charge current is ISET rammed using a single resistor from the ISET pin to ground. The battery charge current is 600 times Charge Status Indicator (STAT) the current out of the ISET pin. The ISET ram resistor and the The charge status output has three different states: strong charge current are calculated using the following equations: pull-down (~10mA), weak pull-down (~20µA) and high impedance. The strong pull-down state indicates that the RSET=1000V/ICHG，ICHG= 1000V/RSET LP28012 is in a charge cycle. Once the charge cycle has terminated, the pin state is determined by under voltage lockout The charge current out of the BAT pin can be determined at any time by monitoring the ISET pin voltage using the following equation: IBAT= VSET x 500/RSET Note: Vset is 2Volts. conditions. A weak pull-down indicates that VCC meets the UVLO conditions and the LP28012 is ready to charge. High impedance indicates that the LP28012 is in under voltage lockout mode: either VCC is less than 100mV above the BAT pin voltage or insufficient voltage is applied to the VCC pin. A microprocessor can be used to distinguish between these three LP28012 – 00 Feb.-2014 Email: [email protected] www.lowpowersemi.com Page 6 of 10 Preliminary Datasheet LP28012 states—this method is discussed in the Applications Information section. Automatic Recharge Function Charging Charge END STAT1(pin2) Low High STAT2(pin3) High Low Thermal Limiting Once the charge cycle is terminated, the LP28012 continuously monitors the voltage on the BAT pin using a comparator with a 2ms filter time (tRECHARGE). A charge cycle restarts when the battery voltage falls below 4.05V (which corresponds to An internal thermal feedback loop reduces the ISET rammed charge current if the die temperature attempts to rise above a preset value of approximately 120°C. This feature protects the LP28012 from excessive temperature and allows the user to push the limits of the power handling capability of a given circuit board without risk of damaging the LP28012. The charge approximately 80% to 90% battery capacity). This ensures that the battery is kept at or near a fully charged condition and eliminates the need for periodic charge cycle initiations. STAT output enters a strong pull-down state during recharge cycles. Power Dissipation current can be set according to typical (not worst-case) ambient The conditions that cause the LP28012 battery charger to temperature charger will reduce charge current through thermal feedback can be automatically reduce the current in worst-case conditions. approximated by considering the total power dissipated in TDFN power considerations are discussed further in the the IC. For high charge currents, the LP28012 power Applications Information section. dissipation is approximately: with the assurance that the Under voltage Lockout (UVLO) An internal under voltage lockout circuit monitors the input voltage and keeps the charger in shutdown mode until VCC rises above the under voltage lockout threshold. The UVLO circuit Where PD is the total power dissipated within the IC, ADP is has a built-in hysteresis of 200mV. Furthermore, to protect the input supply voltage, against reverse current in the power MOSFET, the UVLO circuit the charge current and keeps the charger in shutdown mode if VCC falls to within 30mV to the regulator. VBAT is the battery voltage, PD_BUCK is PD_BUCK can IBAT is the power dissipation due be calculated as: of the battery voltage. If the UVLO comparator is tripped, the charger will not come out of shutdown mode until VCC rises 100mV above the battery voltage. Where Manual Shutdown VOUTB regulator, is the regulated output of the switching IOUTB is the regulator load and is the regulator At any point in the charge cycle, the LP28012 can be put into efficiency at that particular load. shutdown mode by removing RISET thus floating the ISET pin. It is not necessary to perform worst-case power dissipation This reduces the battery drain current to less than 2µA and the supply current to less than 50µA. A new charge cycle can be initiated by reconnecting the ISETram resistor. In manual shutdown, the STAT pin is in a weak pull-down state as long as VCC is high enough to exceed the UVLO conditions. scenarios because the LP28012 will automatically reduce the charge current to maintain the die temperature at approximately 125°C. However, the approximate ambient temperature at which the thermal feedback begins to protect the IC is: The STAT pin is in a high impedance state if the LP28012 is in under voltage lockout mode: either VCC is within 100mV of the BAT pin voltage or insufficient voltage is applied to the VCC pin. LP28012 – 00 Feb.-2014 Email: [email protected] www.lowpowersemi.com Page 7 of 10 Preliminary Datasheet LP28012 circumstances, the LP28012 can be used above 82.75°C, but Example: Consider the extreme case when an LP28012 is the charge current will be reduced from 250mA. The operating from a 6V supply providing 250mA to a 3V Li-Ion approximate current at a given ambient temperature can be battery, the switching regulator and the LDO are off. The ambient temperature above which the LP28012 will begin to reduce the 250mA charge current is approximately: (Correctly soldered to a 2500mm2 double-sided 1 oz. calculated: copper board, the LP28012 has a thermal resistance of approximately 43°C/W.) o T= o o Note: 1V = 1J/C = 1W/A If there is more power dissipation due to the switching Furthermore, the voltage at the ISET pin will change regulator or the LDO, the thermal regulation will kick in at a proportionally with the charge current as discussed in the somewhat lower temperature than this. In the above ISET ramming Charge Current section. LP28012 – 00 Feb.-2014 Email: [email protected] www.lowpowersemi.com Page 8 of 10 Preliminary Datasheet LP28012 PCB Layout Considerations It is important to pay special attention to the PCB layout. The following provides some guidelines: • To obtain optimal performance, the decoupling capacitor from VCC to V(IN) and the output filter capacitors from OUT to VSS should be placed as close as possible to the bq24080, with short trace runs to both signal and VSS pins. The VSS pin should have short trace runs to the GND pin. • All low-current VSS connections should be kept separate from the high-current charge or discharge paths from the battery. Use a single-point ground technique incorporating both the small-signal ground path and the power ground path. • The high-current charge paths into IN and from the OUT pins must be sized appropriately for the maximum charge current in order to avoid voltage drops in these traces. • The LP28012 is packaged in a thermally enhanced MLP package. The package includes a thermal pad to provide an effective thermal contact between the device and the printed circuit board (PCB). Full PCB design guidelines for this package are provided in the application note entitled, QFN/SON PCB Attachment LP28012 – 00 Feb.-2014 Email: [email protected] www.lowpowersemi.com Page 9 of 10 Preliminary Datasheet LP28012 Packaging Information LP28012 – 00 Feb.-2014 Email: [email protected] www.lowpowersemi.com Page 10 of 10