RD-XS&RD-XD Series Fixed input,Isolated 0.5W Twin Output DC/DC Converters SELECTION G UIDE Input Output Output Voltage Voltage1 Voltage2 Output Current1 Output Current2 (V) (V) (V) (MA) (MA) RD050503XD 5 5 3.3 100 FEATURES RD050505XD 5 5 5 100 RD050509XD 5 5 9 RoHS compliant RD050512XD 5 5 RD050515XD 5 RD050503XS Efficiency (%) MTTF 1 (KHRS) 152 70 1615 100 70 1615 100 56 80 669 12 100 42 80 339 5 15 100 34 80 187 5 5 3.3 100 152 70 1615 RD050505XS 5 5 5 100 100 70 1615 RD050509XS 5 5 9 100 56 80 669 RD050512XS 5 5 12 100 42 80 339 RD050515XS 5 5 15 100 34 80 187 RD120505XD 12 5 5 100 100 70 489 RD120509XD 12 5 9 100 56 80 343 RD120512XD 12 5 12 100 42 80 229 RD120515XD 12 5 15 100 34 80 148 RD120505XS 12 5 5 50 50 84 135 RD120505XS 12 5 5 100 100 70 489 RD120509XS 12 5 9 100 56 80 343 RD120512XS 12 5 12 100 42 80 229 RD120515XS 12 5 15 100 34 80 148 RD240505XS 24 5 5 100 100 81 395 RD240509XS 24 5 9 100 56 82 289 RD240512XS 24 5 12 100 42 84 186 RD240515XS 24 5 15 100 34 84 150 RD240505XD 24 5 5 100 100 81 395 RD240509XD 24 5 9 100 56 82 289 RD240512XD 24 5 12 100 42 84 186 RD240515XD 24 5 15 100 34 84 150 Order code ◆ Efficiency up to 80% ◆ Power density up to 0.9W/cm3 ◆ Wide temperature performance at full ◆ 0.5 Watt load,-40°C to 85 °C Twin independent outputs ◆ UV 94V-0 package material ◆ No heatsink required ◆ Footprint from 1.17cm2 ◆ Industry standard pinout ◆ Power sharing on output ◆ Input/output isolation 1KVDC ◆ 3.3V,5V,9V,12V and 15V output ◆ Internal SMD construction ◆ Fully encapsulated with toroidal Magnetics ◆ No external components required ◆ MTTF up to 1.6 million hours ◆ PCB mounting ◆ Custom solutions available ◆ MODEL SE LECTION ① ② ③ ④ INPUT CHA RACTE RI STICS ⑤ RD 05 05 X S ①Product Series ③Output Voltage ⑤SIP Package Parameter ②Input Voltage ④Fixed Input Voltage range Conditions Min. Typ. Max Units Continuous operation,5V input types 4.5 5 5.5 . V Continuous operation,12V input types 10.8 12 13.2 V Continuous operation,24V input types 21.6 24 26.4 V APPLICATIONS The RD-X(S)D series of DC/DC converters are ideally suited to applications where a potential difference exists between loads,e.g. Motor control circuits.The twin outputs offer cost and space savings by consolidating two DC/DC converters into one package.All of the rated power may be drawn from a single output provided the total load does not exceed 1 watt. ABSOLUTE MAX IMUM RATIN GS Parameter Conditions 2 Short-circuit protection 1 second Lead temperature 1.5mm from case for 10 seconds 300℃ Input voltage VIN,D05 types 7V Input voltage VIN,D12 types 15V 1.Calculated using MIL-HDBK-217FN2 calculation model with nominal input voltage at full load. 2.Supply voltage must be disconnected at the end of the short circuit duration. All specifications typical at TA=25°C,nominal input voltage and rated output current unless otherwise specified. http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 1 of 4 RD-XS&RD-XD Series OUTPUT CHA RACTE RI STICS Parameter Conditions 1 Min. Typ. TA=-40℃ to 120℃ Rated Power Voltage Set Point Accuracy Line regulation 2 Load regulation Ripple and Noise Max. Units 1 W See tolerance envelope D050503X(S)D (High Vin to low Vin) 1.0 1.25 %% All other variants (High Vin to low Vin) 1.0 1.20 %% 10% load to rated load,3.3V output types 15 % 10% load to rated load,5V output types 15 % 10% load to rated load,9V output types 10 % 10% load to rated load,12V output types 10 % 10% load to rated load,15V output types 10 % BW=DC to 20MHz,All output types 75 mVp-p Max. Units ISOLAT ION CHA RACTE RI STIC S Parameter Isolation test voltage Resistance Conditions Min. Flash tested for 1 second 1000 VDC 1 GΩ Viso=500VDC Typ. GENERAL CHA RACTE RI STICS Parameter Switching frequency Conditions Min. All input types Typ. Max. 100 Units kHz TEMPERATU RE CHARACTERI STIC S Parameter Conditions Specification All output types Min. Storage Cooling Typ. Max. Units 0 70 ℃ -55 150 ℃ Free air convection TEMPERATU RE DERATI NG G RAPH TOLERANCE ENVELOPE D-X(S)D-1W 1.See derating graph. 2.See derating curve. All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified.Another 24V& 48V products, please inquire Our technical department! http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 2 of 4 RD-XS&RD-XD Series TECHNICAL NOTES ISOLATION VOLTAGE "Hi Pot Test","Flash Tested","Withstand Voltage","Dielectric Withstand Voltage"&”Isolation Test Voltage" are all terms that relate to the same thing, a test voltage. Applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Professional Power Module D-X(S)D series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1KVDC for 1 second. A question commonly asked is,"What is the continuous voltage that can be applied across the part in normal operation?" For a part holding no specific agency approvals, such as the D-X(S)D series ,both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC.The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier, but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circ uits and any user acssible circuitry according to safety standard requirements. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials. Construction and environment. The D-X(S)D series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus impl ying that the number of tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing. but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. This consideration equally applies to agency recognized parts for better than functional isolation where the wire e namel insulation is always supplemented by a further insulation system of physical spacing or barriers. OUTPUT RIPPLE REDUCT ION By using the values of inductance and capacitance stated, the output ripple at the rated load is lowered to 5mV p-p max. Component selection Capacitor: Ceramic chip capacitors are recommended. It is required that the ESR(Equivalent Series Resistance)should be as low as possible.X7R types are recommended. The voltage rating should be at least twice(except for 15V output),the rated output voltage of the DC/DC converter. Inductor: The rated current of the inductor should not be less than of the output of the DC/DC converter. At the rated current, the DC resistance of the inductor should be such that the voltage drop across the inductor is <2% of the rated voltage of the DC/DC converter. The SRF(Self Resonant Frequency) should be >20MHz. OUTPUT RIPPLE REDUCT ION Ripple&Noise Characterisation Method Ripple and noise measurements are performed with the following test configuration. C1 1uF X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter C2 10uF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter with an ESR of less than 100mΩ at 100 KHz C3 100nF multilayer ceramic capacitor, general purpose with an ESR of less than 100mΩ at 100 KHz R1 450Ω resistor, carbon film,±1% tolerance R2 50Ω BNC termination T1 3T of the caox cable through a ferrite toroid RLOAD Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires Measured values are multiplied by 10 to obtain the specified values. Differential Mode Noise Test Schematic http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 3 of 4 RD-XS&RD-XD Series PACKA GE SPEC IFICAT ION S MECHANICAL DIMENSIONS DIP package PIN CONNECTIONS SIP package PI N C ONNE C TI ONS- 14 PI N DIP PI N C ONNE C TI ONS- 7 P I N SI P pin Function pin Function 1 -VI N 1 +VI N 7 NC 2 -VI N 8 -VOUT2 4 +VOUT1 9 +VOUT2 5 -VOUT1 10 -VOUT1 6 +VOUT2 11 +VOUT1 7 -VOUT2 14 +VI N NC - Not available for electrical connection. All dimensions in inches ±0.01(mm±0.25mm).All pins on a 0.1(2.54) pitch and within ±0.01(0.25)of true position. RECOMMENDED FOOTPRINT DETAILS 14 Pin DIP Package 7 Pin SIP Package Unless otherwise stated all dimensions in inches ±0.01(mm ±0.25mm). TUBE OUTLINE DIMENSIONS 14 Pin DIP Tube 7 Pin SIP Tube Unless otherwise stated all dimensions in inches ±0.02(mm ±0.5mm). Tube length (14 Pin DIP) : 20.47 (520mm ±2mm). Tube length (7 Pin SIP) : 20.47 (520mm ±2mm). Tube Quantity :25 RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. Microdc Professional Power Module,Inc. Tel:0086-20-86000646 E-mail:[email protected] Website:http://www.microdc.cn Microdc Professional Power module,Inc.makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. Specifications are subject to change without notice. 2010 Microdc Professional Power Module, Inc. Guangzhou http://www.microdc.cn REACH COMPLIANT INFORMATION This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 4 of 4