THA3001-12.80MHz Stratum-III Series TCVCXO October 2011 • Pletronics’ THA3001-12.8MHz is a temperature compensated crystal oscillator • Optional Voltage Control Function • HCMOS output. • The package is designed for high density surface mount designs. • Tape and Reel packaging is available. • Select Stratum-III frequencies available • 5 x 7 mm LCC Ceramic Package Pletronics Inc. certifies this device is in accordance with the RoHS 6/6 (2002/95/EC) and WEEE (2002/96/EC) directives. Pletronics Inc. guarantees the device does not contain the following: Cadmium, Hexavalent Chromium, Lead, Mercury, PBB’s, PBDE’s Weight of the Device: 0.10 grams Moisture Sensitivity Level: 1 As defined in J-STD-020D.1 Second Level Interconnect code: e4 Absolute Maximum Ratings: Parameter Unit VCC Supply Voltage -0.5V to +6.5V Vi Input Voltage -0.5V to VCC + 0.5V Vo Output Voltage -0.5V to VCC + 0.5V Thermal Characteristics The maximum die or junction temperature is 155oC The thermal resistance junction to board is 30 to 50oC/Watt depending on the solder pads, ground plane and construction of the PCB. ESD Rating Model Minimum Voltage Conditions Human Body Model 1500 MIL-STD-883 Method 3115 Charged Device Model 1000 JESD 22-C101 www.pletronics.com 425-776-1880 1 THA3001-12.80MHz Stratum-III TCXO / TCVCXO October 2011 Electrical Specification for specified Vcc over the specified temperature range Item Min TYP Frequency Range Max 12.80 Unit Condition MHz Frequency Stability 1 -0.28 +0.28 ppm Vcontrol @ 1.50 volts (Fmax-Fmin)/2 Holdover -0.37 +0.37 ppm GR-1244-CORE Frequency Calibration -0.5 +0.5 ppm Frequency offset at 25°C, 60 minutes after reflow Frequency Stability / Supply -0.1 +0.1 ppm Load: 10K ohm // 10 pF & Vcc + _ 5% Load Sensitivity -0.2 +0.2 ppm ±2% variation in magnitude from 10K ohm ±10% || 10 pF Long Term Stability (Aging) -3.4 +3.4 ppb After 15 years. %VS Load: 10K ohm + _ 10% // 10 pF + _ 10% Output Waveform CMOS Output VHIGH as % of Supply 90 Output VLOW as % of Supply 10 %VS TRISE and TFALL (10% to 90%) 6.5 nS % Duty Cycle at 50% Supply Phase Noise 10 Hz 100 Hz 1 kHz 10 kHz Jitter 40 50 60 - -90 -115 -135 -145 - - - 1.7 pS dBc/Hz V Supply Range VCC 3.15 3.3 3.45 Volts Supply Current ICC - - 7.0 mA 2.50 Volts Vcontrol Range Frequency Pullability Linearity 0.5 _ 9.2 + _ 10.0 + - ppm - 0.05 2.0 % Operating Temperature Range -40 +85 o C Storage Temperature Range -55 +95 o C www.pletronics.com 425-776-1880 Typical values for a 20.0 MHz oscillator at 25°C 10 Hz to 1 MHz offset from carrier 1.50 volts nominal In accordance with MIL-PRF-55310 2 THA3001-12.80MHz Stratum-III TCXO / TCVCXO October 2011 Phase Noise: MTIE: www.pletronics.com 425-776-1880 3 THA3001-12.80MHz Stratum-III TCXO / TCVCXO October 2011 Reliability: Environmental Compliance Parameter Condition Mechanical Shock MIL-STD-883 Method 2002, Condition B Vibration MIL-STD-883 Method 2007, Condition A Solderability MIL-STD-883 Method 2003 Thermal Shock MIL-STD-883 Method 1011, Condition A Part Marking: ffff.yww C PLExx.xxxx or ffff:yww C PLExx.xxxx ffff.yww = PLE = xx.xxxx = frequency in MHz . Year week Pletronics internal code * Marking will show 25.60 MHz. Actual output will be 12.80 Mhz Package Labeling Label is 1" x 2.6" (25.4mm x 66.7mm) Font is Courier New Bar code is 39-Full ASCII www.pletronics.com Label is 1" x 2.6" (25.4mm x 66.7mm) Font is Arial 425-776-1880 4 THA3001-12.80MHz Stratum-III TCXO / TCVCXO October 2011 Mecha nical: 4 3 1 2 3 4 2 1 Not to Scale Pad 1 Inches mm A 0.276 + _ 0.006 7.00 + _ 0.15 Function Note B 0.197 + _ 0.006 5.00 + _ 0.15 Vcontrol Input If this function is not specified, recommend connecting this pad to ground. C 0.099 max 2.50 max D1 0.039 1.00 2 Ground (GND) E1 0.197 5.00 3 Output F1 0.025 0.90 4 Supply Voltage (VCC) G1 0.118 3.00 H1 0.020 0.50 J1 0.051 1.30 K1 0.154 3.90 Recommend connecting appropriate power supply bypass capacitors as close as possible. 1 Contacts : Gold 11.8 µinches Typic dimensions 0.3 µm minimum over Nickel 50 to 350 µinches www.pletronics.com 425-776-1880 1.27 to 8.89 µm 5 THA3001-12.80MHz Stratum-III TCXO / TCVCXO October 2011 Temperature (°C) Reflow Cycle (typical for lead free processing) 260°C Maximum 10 Seconds Maximum 250 215°C±10°C 200 175°C±10°C 150 100 Approximately 50 Seconds 120 to 160 Seconds Allowed rate of temperature change Maximum 4°C per second The part may be reflowed 2 times without degradation. Tape and Reel: available for quantities of 250 to 1000 per reel, cut tape for < 250 Constant Dimensions Table 1 Tape Size D0 8mm D1 Min E1 P0 P2 1.0 T Max 0.6 0.6 0.1 2.0 _ +0.05 12mm 1.5 1.5 1.75 4.0 16mm +0.1 -0.0 1.5 _ +0.1 _ +0.1 24mm T1 Max S1 Min 2.0 _ +0.1 1.5 Variable Dimensions Table 2 Tape Size B1 Max E2 Min F P1 T2 Max W Max Ao, Bo & Ko 16 mm 12.1 14.25 7.5 _ +0.1 8.0 _ +0.1 8.0 16.3 Note 1 Note 1: Embossed cavity to conform to EIA-481-B Dimensions in mm Not to scale REEL DIMENSIONS A B inches 7.0 10.0 13.0 mm 177.8 254.0 330.2 inches 2.50 4.00 3.75 mm 63.5 101.6 95.3 Tape Width 16.4 +2.0 -0.0 16.0 C mm D mm 13.0 +0.5 / -0.2 16.4 +2.0 -0.0 16.4 +2.0 -0.0 Reel dimensions may vary from the above www.pletronics.com 425-776-1880 6 THA3001-12.80MHz Stratum-III TCXO / TCVCXO October 2011 IMPORTANT NOTICE Pletronics Incorporated (PLE) reserves the right to make corrections, improvements, modifications and other changes to this product at anytime. PLE reserves the right to discontinue any product or service without notice. Customers are responsible for obtaining the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to PLE’s terms and conditions of sale supplied at the time of order acknowledgment. PLE warrants performance of this product to the specifications applicable at the time of sale in accordance with PLE’s limited warranty. Testing and other quality control techniques are used to the extent PLE deems necessary to support this warranty. Except where mandated by specific contractual documents, testing of all parameters of each product is not necessarily performed. PLE assumes no liability for application assistance or customer product design. Customers are responsible for their products and applications using PLE components. To minimize the risks associated with the customer products and applications, customers should provide adequate design and operating safeguards. PLE products are not designed, intended, authorized or warranted to be suitable for use in life support applications, devices or systems or other critical applications that may involve potential risks of death, personal injury or severe property or environmental damage. Inclusion of PLE products in such applications is understood to be fully at the risk of the customer. Use of PLE products in such applications requires the written approval of an appropriate PLE officer. Questions concerning potential risk applications should be directed to PLE. PLE does not warrant or represent that any license, either express or implied, is granted under any PLE patent right, copyright, artwork or other intellectual property right relating to any combination, machine or process which PLE product or services are used. Information published by PLE regarding third-party products or services does not constitute a license from PLE to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from PLE under the patents or other intellectual property of PLE. Reproduction of information in PLE data sheets or web site is permissible only if the reproduction is without alteration and is accompanied by associated warranties, conditions, limitations and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. PLE is not responsible or liable for such altered documents. Resale of PLE products or services with statements different from or beyond the parameters stated by PLE for that product or service voids all express and implied warranties for the associated PLE product or service and is an unfair or deceptive business practice. PLE is not responsible for any such statements. Contacting Pletronics Inc. Pletronics Inc. 19013 36th Ave. West Lynnwood, WA 98036-5761 USA Tel: 425-776-1880 Fax: 425-776-2760 E-mail: [email protected] URL: www.pletronics.com Copyright © 2011, Pletronics Inc. www.pletronics.com 425-776-1880 7