SP1481E/SP1485E Enhanced Low Power Half

®
SP1481E/SP1485E
Enhanced Low Power Half-Duplex
RS-485 Transceivers
■ +5V Only
■ Low Power BiCMOS
■ Driver/Receiver Enable for Multi-Drop
configurations
■ Low Power Shutdown Mode
(SP1481E)
■ Enhanced ESD Specifications:
+15KV Human Body Model
+15KV IEC1000-4-2 Air Discharge
+8KV IEC1000-4-2 Contact Discharge
Now Available in Lead Free Packaging
DESCRIPTION
The SP1481E and the SP1485E are a family of half-duplex transceivers that meet the
specifications of RS-485 and RS-422 serial protocols with enhanced ESD performance. The
ESD tolerance has been improved on these devices to over +15KV for both Human Body
Model and IEC1000-4-2 Air Discharge Method. These devices are pin-to-pin compatible with
Sipex's SP481 and SP485 devices as well as popular industry standards. As with the original
versions, the SP1481E and the SP1485E feature Sipex's BiCMOS design allowing low power
operation without sacrificing performance. The SP1481E and SP1485E meet the requirements of the RS-485 and RS-422 protocols up to 20Mbps under load. The SP1481E is
equipped with a low power Shutdown mode.
RO 1
R
8 Vcc
RE 2
7B
DE 3
6A
DI 4
D
5 GND
SP481E and SP485E
Revc Date: 3/08/07
SP1481E Low Power Half-Duplex RS485 Transceivers
1
© Copyright 2005 Sipex Corporation
ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation of the device at
these ratings or any other above those indicated in the operation sections
of the specifications below is not implied. Exposure to absolute maximum
rating conditions for extended periods of time may affect reliability.
VCC............................................................................................................+7V
Input Voltages
Logic........................................................-0.3V to (VCC+0.5V)
Drivers..................................................-0.3V to (VCC+0.5V)
Receivers................................................................. ±15V
Output Voltages
Logic........................................................-0.3V to (VCC+0.5V)
Drivers...................................................................... ±15V
Receivers............................................-0.3V to (VCC+0.5V)
Storage Temperature.......................................................-65˚C to +150˚C
Power Dissipation per Package
8-pin NSOIC (derate 6.60mW/oC above +70oC)...........................550mW
8-pin PDIP (derate 11.8mW/oC above +70oC)............................1000mW
ELECTRICAL CHARACTERISTICS
TMIN to TMAX and VCC = 5V ± 5% unless otherwise noted.
PARAMETERS
SP1481E/SP1485E DRIVER
DC Characteristics
Differential Output Voltage
Differential Output Voltage
Differential Output Voltage
Change in Magnitude of Driver
Differential Output Voltage for
Complimentary States
Driver Common-Mode
Output Voltage
Input High Voltage
Input Low Voltage
Input Current
Driver Short-Circuit Current
VOUT = HIGH
VOUT = LOW
SP1481E/SP1485E DRIVER
AC Characteristics
Maximum Data Rate
MIN.
TYP.
MAX.
UNITS
CONDITIONS
3.5
2
VCC
VCC
Volts
Volts
1.5
VCC
Volts
Unloaded; R = ∞ ; see Figure 1
with load; R = 50Ω; (RS-422);
see Figure 1
with load; R = 27Ω; (RS-485);see Figure 1
0.2
Volts
R = 27Ω or R = 50Ω; see Figure 1
3
0.8
±10
Volts
Volts
Volts
µA
R = 27Ω or R = 50Ω; see Figure 1
Applies to DE, DI, RE
Applies to DE, DI, RE
Applies to DE, DI, RE
±250
±250
mA
mA
-7V ≤ VO ≤ +12V
-7V ≤ VO ≤ +12V
Mbps
RE = 5V, DE = 5V; RDIFF = 54Ω,
CL1 = CL2 = 100pF
tPLH; RDIFF = 54Ω, CL1 = CL2 = 100pF;
see Figures 3 and 5
tPLH; RDIFF = 54Ω, CLI = CL2 = 100pF;
See Figures 3 and 5
2.0
20
Driver Input to Output
20
30
ns
Driver Input to Output
(SP1485EMN ONLY)
20
40
ns
Driver Input to Output
20
30
ns
Driver Input to Output
(SP1485EMN ONLY)
Driver Skew
20
40
ns
3
5
ns
Driver Rise or Fall Time
8
20
ns
Driver Enable to Output High
closed
Driver Enable to Output Low
closed
Driver Disable Time from Low
closed
Driver Disable Time from High
closed
40
70
ns
tPHL; RDIFF = 54Ω, CL1 = CL2 = 100pF;
see Figures 3 and 5
tPHL; RDIFF = 54Ω, CL1 = CL2 = 100pF;
see Figures 3 and 5
see Figures 3 and 5,
tSKEW = | tDPLH - tDPHL |
From 10% to 90%; RDIFF = 54Ω,
CL1 = CL2 = 100pF; see Figures 3 & 6
CL = 100pF; see Figures 4 & 6; S2
40
70
ns
CL = 100pF; see Figures 4 & 6; S1
40
70
ns
CL = 100pF; see Figures 4 & 6; S1
40
70
ns
CL = 100pF; see Figures 4 & 6; S2
Revc Date: 3/08/07
SP1481E Low Power Half-Duplex RS485 Transceivers
2
© Copyright 2005 Sipex Corporation
SPECIFICATIONS (continued)
TMIN to TMAX and VCC = 5V ± 5% unless otherwise noted.
PARAMETERS
SP1481E/SP1485E RECEIVER
DC Characteristics
Differential Input Threshold
Differential Input Threshold
(SP1485EMN ONLY)
Input Hysteresis
Output Voltage High
Output Voltage Low
Three-State (High Impedance)
Output Current
Input Resistance
Input Current (A, B); VIN = 12V
Input Current (A, B); VIN = -7V
Short-Circuit Current
SP1481E/SP1485E RECEIVER
AC Characteristics
Maximum Data Rate
Receiver Input to Output
MIN.
TYP.
-0.2
-0.4
MAX.
UNITS
CONDITIONS
+0.2
+0.4
Volts
Volts
-7V ≤ VCM ≤ +12V
-7V ≤ VCM ≤ +12V
0.4
mV
Volts
Volts
VCM = 0V
IO = -4mA, VID = +200mV
IO = +4mA, VID = -200mV
µA
kΩ
mA
mA
mA
0.4V ≤ VO ≤ 2.4V; RE = 5V
-7V ≤ VCM ≤ +12V
DE = 0V, VCC = 0V or 5.25V, VIN = 12V
DE = 0V, VCC = 0V or 5.25V, VIN = -7V
0V ≤ VO ≤ VCC
RE = 0V, DE = 0V
tPLH; RDIFF = 54Ω,
CL1 = CL2 = 100pF; Figures 3 & 7
tPHL; RDIFF = 54Ω,
CL1 = CL2 = 100pF; Figures 3 & 7
RDIFF = 54Ω; CL1 = CL2 = 100pF;
Figures 3 & 7
20
3.5
±1
12
15
+1.0
-0.8
95
7
20
25
70
Mbps
ns
Receiver Input to Output
25
70
ns
Diff. Receiver Skew ItPLH-tPHLI
5
10
ns
45
70
ns
CRL = 15pF; Figures 2 & 8; S1 closed
45
45
45
70
70
70
ns
ns
ns
CRL = 15pF; Figures 2 & 8; S2 closed
CRL = 15pF; Figures 2 & 8; S1 closed
CRL = 15pF; Figures 2 & 8; S2 closed
200
600
ns
RE = 5V, DE = 0V
40
100
ns
CL = 100pF; See Figures 4 & 6; S2 closed
40
100
ns
CL = 100pF; See Figures 4 & 6; S1 closed
300
1000
ns
CL = 15pF; See Figures 2 & 8; S2 closed
300
1000
ns
CL = 15pF; See Figures 2 & 8; S1 closed
+5.25
Volts
Receiver Enable to
Output Low
Receiver Enable to
Output High
Receiver Disable from Low
Receiver Disable from High
SP1481E
Shutdown Timing
Time to Shutdown
50
Driver Enable from Shutdown
to Output High
Driver Enable from Shutdown
to Output Low
Receiver Enable from
Shutdown to Output High
Receiver Enable from
Shutdown to Output Low
POWER REQUIREMENTS
Supply Voltage
+4.75
Supply Current
SP1481E/1485E
No Load
SP1481E
Shutdown Mode
ENVIRONMENTAL AND MECHANICAL
Operating Temperature
Commercial (_C_)
0
Industrial (_E_)
-40
(_M_)
-40
Storage Temperature
-65
Package
Plastic DIP (_P)
NSOIC (_N)
Revc Date: 3/08/07
900
600
µA
µA
RE, DI = 0V or VCC; DE = VCC
RE = 0V, DI = 0V or 5V; DE = 0V
10
µA
DE = 0V, RE=VCC
+70
+85
+125
+150
°C
°C
°C
°C
SP1481E Low Power Half-Duplex RS485 Transceivers
3
© Copyright 2005 Sipex Corporation
PIN FUNCTION
R
RO 1
8
VCC
RE 2
7
B
DE 3
6
A
5
GND
Pin 1 – RO – Receiver Output.
Pin 2 – RE – Receiver Output Enable Active LOW.
Pin 3 – DE – Driver Output Enable Active HIGH.
Pin 4 – DI – Driver Input.
Pin 5 – GND – Ground Connection.
D
DI 4
SP485
Pin 6 – A – Driver Output/Receiver Input
Non-inverting.
Top View
Pin 7 – B – Driver Output/Receiver Input Inverting.
SP1481E and SP1485E
Pinout (Top View)
Pin 8 – Vcc – Positive Supply 4.75V<Vcc< 5.25V.
A
VOD
R
Test Point
Receiver
Output
R
CRL
VOC
1k
B
CL1
RDIFF
A
VCC
S1
S2
Figure 1. RS-485 Driver DC Test Load Circuit
DI
1k
A
Figure 2. Receiver Timing Test Load Circuit
RO
Output
Under C
L
Test
B
B
CL2
15pF
Figure 4. RS-485 Driver Timing Test Load #2 Circuit
f = 1MHz; tR < 1.0ns; tF < 1.0ns
+3V
1.5V
DI
1.5V
0V
B
VCC
S1
S2
Figure 3. RS-485 Driver/Receiver Timing Test Circuit
DRIVER
OUTPUT
500
tPLH
tPHL
VO 1/2VO
1/2VO
A
tDPLH
DIFFERENTIAL VO+
OUTPUT 0V
VA – VB VO–
tDPHL
tR
tF
tSKEW = | tDPLH - tDPHL |
Figure 5. Driver Propagation Delays
Revc Date: 3/08/07
SP1481E Low Power Half-Duplex RS485 Transceivers
4
© Copyright 2005 Sipex Corporation
INPUTS
RE
X
X
X
X
OUTPUTS
LINE
DI CONDITION
1
No Fault
0
No Fault
X
X
X
Fault
DE
1
1
0
1
B
0
1
Z
Z
INPUTS
RE
DE
0
0
0
0
0
0
1
0
A
1
0
Z
Z
OUTPUTS
A-B
R
+0.2V
1
-0.2V
0
Inputs Open
1
X
Z
Table 2. Receive Function Truth Table
Table 1. Transmit Function Truth Table
f = 1MHz; tR < 1.0ns; tF < 1.0ns
+3V
1.5V
DE
1.5V
0V
tZL
tLZ
5V
2.3V
A, B
VOL
VOH
A, B
2.3V
0V
Output normally LOW
0.5V
Output normally HIGH
0.5V
tZH
tHZ
Figure 6. Driver Enable and Disable Times
V0D2+
A–B
0V
INPUT
V0D2–
VOH
1.5V
R
VOL
tPHL
OUTPUT
0V
1.5V
tPLH
f = 1MHz; tR < 1.0ns; tF < 1.0ns
tSKEW = | tPHL - tPLH |
Figure 7. Receiver Propagation Delays
+3V
1.5V
RE
0V
f = 1MHz; tR < 1.0ns; tF < 1.0ns
tZL
1.5V
tLZ
5V
1.5V
R
VIL
Output normally LOW
0.5V
Output normally HIGH
0.5V
VIH
R
1.5V
0V
tZH
tHZ
Figure 8. Receiver Enable and Disable Times
Revc Date: 3/08/07
SP1481E Low Power Half-Duplex RS485 Transceivers
5
© Copyright 2005 Sipex Corporation
DESCRIPTION
Receivers
The SP1481E and SP1485E are half-duplex
differential transceivers that meet the requirements of RS-485 and RS-422. Fabricated with a
Sipex proprietary BiCMOS process, these products require a fraction of the power of older
bipolar designs.
The SP1481E and SP1485E receivers have differential inputs with an input sensitivity as low as
±200mV. Input impedance of the receivers is
typically 15kΩ (12kΩ minimum). A wide common mode range of -7V to +12V allows for large
ground potential differences between systems.
The receivers of the SP1481E and SP1485E
have a tri-state enable control pin. A logic LOW
on RE (pin 2) will enable the receiver, a logic
HIGH on RE (pin 2) will disable the receiver.
The RS-485 standard is ideal for multi-drop
applications and for long-distance interfaces.
RS-485 allows up to 32 drivers and 32 receivers
to be connected to a data bus, making it an ideal
choice for multi-drop applications. Since the
cabling can be as long as 4,000 feet, RS-485
transceivers are equipped with a wide (-7V to
+12V) common mode range to accommodate
ground potential differences. Because RS-485 is
a differential interface, data is virtually immune
to noise in the transmission line.
The receiver for the SP1481E and SP1485E will
operate up to at least 20Mbps. The receiver for
each of the two devices is equipped with the
fail-safe feature. Fail-safe guarantees that the
receiver output will be in a HIGH state when
the input is left unconnected.
Shutdown Mode
SP1481E
Drivers
The driver outputs of the SP1481E and SP1485E
are differential outputs meeting the RS-485 and
RS-422 standards. The typical voltage output
swing with no load will be 0 Volts to +5 Volts.
With worst case loading of 54Ω across the differential outputs, the drivers can maintain greater
than 1.5V voltage levels. The drivers of the
SP1481E, and SP1485E have an enable control
line which is active HIGH. A logic HIGH on DE
(pin 3) will enable the differential driver outputs.
A logic LOW on DE (pin 3) will tri-state the
driver outputs.
The SP1481E is equipped with a Shutdown
mode. To enable the Shutdown state, both the
driver and receiver must be disabled simultaneously.
A logic LOW on DE (pin 3) and a logic HIGH on
RE (pin 2) will put the SP1481E into Shutdown
mode. In Shutdown, supply current will drop to
typically 1µA.
ESD TOLERANCE
The SP1481E Family incorporates ruggedized
ESD cells on all driver output and receiver input
pins. The ESD structure is improved over our
previous family for more rugged applications
and environments sensitive to electro-static discharges and associated transients. The improved
ESD tolerance is at least ±15kV without damage
nor latch-up.
The transmitters of the SP1481E and SP1485E
will operate up to at least 20Mbps.
There are different methods of ESD testing
applied:
a) MIL-STD-883, Method 3015.7
b) IEC1000-4-2 Air-Discharge
c) IEC1000-4-2 Direct Contact
Revc Date: 3/08/07
SP1481E Low Power Half-Duplex RS485 Transceivers
6
© Copyright 2005 Sipex Corporation
generally used for testing ESD on equipment and
systems. For system manufacturers, they must
guarantee a certain amount of ESD protection
since the system itself is exposed to the outside
environment and human presence. The premise
with IEC1000-4-2 is that the system is required
to withstand an amount of static electricity when
ESD is applied to points and surfaces of the
equipment that are accessible to personnel during
normal usage. The transceiver IC receives most
of the ESD current when the ESD source is
applied to the connector pins. The test circuit for
IEC1000-4-2 is shown on Figure 8. There are
two methods within IEC1000-4-2, the Air
Discharge method and the Contact Discharge
method.
The Human Body Model has been the generally
accepted ESD testing method for semiconductors.
This method is also specified in MIL-STD-883,
Method 3015.7 for ESD testing. The premise of
this ESD test is to simulate the human body’s
potential to store electro-static energy and
discharge it to an integrated circuit. The
simulation is performed by using a test model as
shown in Figure 7. This method will test the
IC’s capability to withstand an ESD transient
during normal handling such as in manufacturing
areas where the ICs tend to be handled frequently.
The IEC-1000-4-2, formerly IEC801-2, is
R
RS
S
R
RC
C
SW2
SW2
SW1
SW1
Device
Under
Test
C
CS
S
DC Power
Source
Figure 7. ESD Test Circuit for Human Body Model
Contact-Discharge Module
R
RS
S
R
RC
C
RV
SW2
SW2
SW1
SW1
Device
Under
Test
C
CS
S
DC Power
Source
RS and RV add up to 330Ω for IEC1000-4-2.
Figure 8. ESD Test Circuit for IEC1000-4-2
Revc Date: 3/08/07
SP1481E Low Power Half-Duplex RS485 Transceivers
7
© Copyright 2005 Sipex Corporation
i➙
With the Air Discharge Method, an ESD voltage
is applied to the equipment under test (EUT)
through air. This simulates an electrically charged
person ready to connect a cable onto the rear of
the system only to find an unpleasant zap just
before the person touches the back panel. The
high energy potential on the person discharges
through an arcing path to the rear panel of the
system before he or she even touches the system.
This energy, whether discharged directly or
through air, is predominantly a function of the
discharge current rather than the discharge
voltage. Variables with an air discharge such as
approach speed of the object carrying the ESD
potential to the system and humidity will tend to
change the discharge current. For example, the
rise time of the discharge current varies with the
approach speed.
30A
15A
0A
t=0ns
voltage stored in the capacitor is then applied
through RS, the current limiting resistor, onto the
device under test (DUT). In ESD tests, the SW2
switch is pulsed so that the device under test
receives a duration of voltage.
For the Human Body Model, the current limiting
resistor (RS) and the source capacitor (CS) are
1.5kΩ an 100pF, respectively. For IEC-1000-42, the current limiting resistor (RS) and the source
capacitor (CS) are 330Ω an 150pF, respectively.
The higher CS value and lower RS value in the
IEC1000-4-2 model are more stringent than the
Human Body Model. The larger storage capacitor
injects a higher voltage to the test point when
SW2 is switched on. The lower current limiting
resistor increases the current charge onto the test
point.
The circuit model in Figures 7 and 8 represent
the typical ESD testing circuit used for all three
methods. The CS is initially charged with the DC
power supply when the first switch (SW1) is on.
Now that the capacitor is charged, the second
switch (SW2) is on while SW1 switches off. The
Driver Outputs
Receiver Inputs
Revc Date: 3/08/07
HUMAN BODY
MODEL
±15kV
±15kV
t=30ns
Figure 9. ESD Test Waveform for IEC1000-4-2
The Contact Discharge Method applies the ESD
current directly to the EUT. This method was
devised to reduce the unpredictability of the
ESD arc. The discharge current rise time is
constant since the energy is directly transferred
without the air-gap arc. In situations such as
hand held systems, the ESD charge can be directly
discharged to the equipment from a person already
holding the equipment. The current is transferred
on to the keypad or the serial port of the equipment
directly and then travels through the PCB and finally
to the IC.
SP1481E,
SP1485E
FAMILY
t➙
Air Discharge
IEC1000-4-2
Direct Contact
Level
±15kV
±15kV
±8kV
±8kV
4
4
SP1481E Low Power Half-Duplex RS485 Transceivers
8
© Copyright 2005 Sipex Corporation
PACKAGE: PLASTIC
DUAL–IN–LINE
(NARROW)
E1 E
D1 = 0.005" min.
(0.127 min.)
A1 = 0.015" min.
(0.381min.)
D
A = 0.210" max.
(5.334 max).
C
A2
B1
B
e = 0.100 BSC
(2.540 BSC)
Ø
L
eA = 0.300 BSC
(7.620 BSC)
ALTERNATE
END PINS
(BOTH ENDS)
DIMENSIONS (Inches)
Minimum/Maximum
(mm)
8–PIN
A2
0.115/0.195
(2.921/4.953)
B
0.014/0.022
(0.356/0.559)
B1
0.045/0.070
(1.143/1.778)
C
0.008/0.014
(0.203/0.356)
D
0.355/0.400
(9.017/10.160)
E
0.300/0.325
(7.620/8.255)
E1
0.240/0.280
(6.096/7.112)
L
0.115/0.150
(2.921/3.810)
Ø
0°/ 15°
(0°/15°)
Revc Date: 3/08/07
SP1481E Low Power Half-Duplex RS485 Transceivers
9
© Copyright 2005 Sipex Corporation
PACKAGE: PLASTIC
SMALL OUTLINE (SOIC)
(NARROW)
E
H
h x 45°
D
A
Ø
e
B
DIMENSIONS (Inches)
Minimum/Maximum
(mm)
A1
L
8–PIN
A
0.053/0.069
(1.346/1.748)
A1
0.004/0.010
(0.102/0.249
B
0.014/0.019
(0.35/0.49)
D
0.189/0.197
(4.80/5.00)
E
0.150/0.157
(3.802/3.988)
e
0.050 BSC
(1.270 BSC)
H
0.228/0.244
(5.801/6.198)
h
0.010/0.020
(0.254/0.498)
L
0.016/0.050
(0.406/1.270)
Ø
0°/8°
(0°/8°)
Revc Date: 3/08/07
SP1481E Low Power Half-Duplex RS485 Transceivers
10
© Copyright 2005 Sipex Corporation
ORDERING INFORMATION
Model
Temperature Range
Status
Package
SP1481ECN ......................... 0˚C to +70˚C ............................EOL........................................ 8-pin Narrow SOIC
SP1481ECP.......................... 0˚C to +70˚C .............................EOL........................................... 8-pin Plastic DIP
SP1481EEN ......................... .-40˚C to +85˚C .........................EOL........................................ 8-pin Narrow SOIC
SP1481EEP .......................... -40˚C to +85˚C ........................EOL............................................ 8-pin Plastic DIP
SP1485ECN .......................... 0˚C to +70˚C ...........................EOL........................................ 8-pin Narrow SOIC
SP1485ECP ........................... 0˚C to +70˚C ..........................EOL............................................ 8-pin Plastic DIP
SP1485EEN ........................... -40˚C to +85˚C .......................EOL........................................ 8-pin Narrow SOIC
SP1485EEP ........................... -40˚C to +85˚C .......................EOL............................................ 8-pin Plastic DIP
SP1485EMN .......................... -40˚C to +125˚C .....................EOL........................................ 8-pin Narrow SOIC
Please consult the factory for pricing and availability on a Tape-On-Reel option.
Available in lead free packaging. To order add "-L" suffix to part number. Example: SP1485EMN =
standard; SP1485EMN-L = lead free.
Revision information:
5/11/05: Added Lead Free information, removed Preliminary status.
3/8/06: Added Status column, EOL info.
Corporation
ANALOG EXCELLENCE
Sipex Corporation
Headquarters and
Sales Office
233 South Hillview Drive
Milpitas, CA 95035
TEL: (408) 934-7500
FAX: (408) 935-7600
Sales Office
22 Linnell Circle
Billerica, MA 01821
TEL: (978) 667-8700
FAX: (978) 670-9001
e-mail: [email protected]
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.
Revc Date: 3/08/07
SP1481E Low Power Half-Duplex RS485 Transceivers
11
© Copyright 2005 Sipex Corporation