EURO CASSETES PSE 100 Series 6 0 - 1 0 0 W AT T S D C / D C S I N G L E O U T P U T FEATURES • • • • • • Under voltage logic alarm. Conformally coating, tropic. Reverse input voltage protection. High efficiency. Fully encapsulated, meets IP30 standard. Convectional cooled. SPECIFICATIONS INPUT STANDARDS Voltage See table Safety EN/IEC60950-1: 2001 Isolation Input – Output: 2kVdc (Input code A, B) Input – Output: 2.5kVac / 4kVdc (Input code C/ D) Input – Case: 2kVdc (Input code A, B) Input – Case: 2.5kVac / 4kVdc (Input – code C/ D) Output – Case: 2kVdc EMI standards IEC/EN61000-6-2, EN55011/EN55022 level B Immunity standartds EN/IEC 61000-6-2, EN/IEC 6100-4-2 EN/IEC 61000-4-3, EN/IEC 6100-4-4 EN/IEC 61000-4-5, EN/IEC 61000-4-6 C-Tick AS/NZS CISPR11: 2002 Group1 Class A Reverse voltage protection Yes. OPTIONS OUTPUT Voltage See table. Current See table. Source regulation 0.2%. Load regulation 0.2% (0-100% load) Output ripple (100kHz) 10mV p-p (typical) Voltage adjustment 90% - 110%. Current limit protection 105%. Under voltage logic alarm 90% of nominal output. Soft start Yes. Start-up time 1s. Hold-up time 2-10ms Efficiency 80-88% -25°C to +70°C (100% load, O/P > 10V). -25°C to +55°C (100% load, O/P < 10V). Temperature coefficient 0.02% / °C. Cooling Convectional cooling. Storage temperature -40°C to 85°C. Conformal coating Conformal coated to withstand non-condensing tropical environment RH 95% MECHANICAL 484 – B – Overvoltage protection (OVP) The output voltage is limited to 15% nominal output voltage. A thyristor short- circuit the output. Undervoltage alarm with relay The logic alarm output is replaced with Relay with selectable alarm logic NO or NC. C - S - H - E1 - Built in series diode A series diode on the output, when output is connected in parallel with other power supplies to achieve redundancy. Output power might be derated. The voltage sensing can be put at the load to compensate for voltage drop. This is standard feature on 5V output. Inrush current limit with NTC Only for C-input code. Reduce the inrush current during the start up. The input voltage range will be affected. 2.5kVac isolation input/case, option On A and B inputs. The emission level increase to level A. ENVIRONMENTAL Operating temperature A Mechanical dimensions 3U x 8TE x 167mm Weight 0.85kg Mounting Consult Powerbox for mounting options E2 - 2.5kVac isolation output/case The emission level will increase to level A. T - Train input Input voltage range according to train Standard EN50155 and IEC 60751. Euro panel, option L 8TE for PSE 100, 10TE for 5V output with extra cooler. N - - Wall mounting panels Wall mounting panel with connector holder The female connector has to be chosen. H15 screw type female, H15-S H15 fast-on 6.3mm female, H15-T Din rail TS35 clips, option Q Doc. No. PBC9 Rev.C 28-4-11 PSE 100 Series SELECTION TABLE MODEL NUMBER INPUT OUTPUT COOLING POWER PSE100A5 10-30V 5V 20A Convection 100W PSE100A13.2 10-30V 13.2V 7.6A Convection 100W PSE100A15 10-30V 15V 6.7A Convection 100W PSE100A24 10-30V 24V 4.2A Convection 100W PSE100A48 10-30V 48V 2.1A Convection 100W PSE100B5 20-72V 5V 20A Convection 100W PSE100B13.2 20-72V 13.2V 7.6A Convection 100W PSE100B15 20-72V 15V 6.7A Convection 100W PSE100B24 20-72V 24V 4.2A Convection 100W PSE100B48 20-72V 48V 2.1A Convection 100W PSE100C5 50-150V 5V 20A Convection 100W PSE100C13.2 50-150V 13.2V 7.6A Convection 100W PSE100C15 50-150V 15V 6.7A Convection 100W PSE100C24 50-150V 24V 4.2A Convection 100W PSE100C48 50-150V 48V 2.1A Convection 100W PSE100D5 90-270V 5V 20A Convection 100W PSE100D13.2 90-270V 13.2V 7.6A Convection 100W PSE100D15 90-270V 15V 6.7A Convection 100W PSE100D24 90-270V 24V 4.2A Convection 100W PSE100D48 90-270V 48V 2.1A Convection 100W EURO CASSETES 1 0 0 W AT T S D C / D C S I N G L E O U T P U T TECHNICAL ILLUSTRATIONS Doc. No. PBC9 Rev.C 28-4-11 Powering Progress – www.powerbox.com.au 485