Surface Mount Solutions

Surface Mount
Solutions
Attenuators
Resistors
Terminations
Surface Mount Solutions
SERIES ANT, ANR
RESISTORS & TERMINATIONS
High Power, Aluminum Nitride, Thin Film, Drop-in – 10-600 Watts, DC-4 GHz
GENERAL INFORMATION
NOTES
1. Input power ratings are based on flange
temperature of 100° C maximum.
2. 50 and 100 Ohms standard. Other values
from 10-500 Ohms available on special order.
Contact factory for details. Standard tolerance ±5%.
Specify resistance value when ordering.
3. VSWR applies to termination style only.
These high power devices are designed to dissipate power in RF
circuits when mounted to an appropriate heat sink. The terminations provide a low VSWR under maximum power conditions. The
resistor configurations are typically used in “Wilkinson” type power
divider networks, or to terminate 3 dB stripline or microstrip hybrids.
Aluminum nitride is used for those applications where the use and
disposal of beryllium oxide is a concern.
% OF RATED POWER
AVERAGE POWER DERATING CURVE
GENERAL SPECIFICATIONS
Resistive Element
Substrate
Cover
Mounting Flange
Tab
Thin Film
Aluminum Nitride
Alumina Ceramic
Copper, Nickel Plated per QQ-N-290
Beryllium Copper, Gold Plated per MIL-G-4520 4
POWER DERATING
100
75
50
25
0
25
100
125
75
50
FLANGE TEMPERATURE — °C
150
PERFORMANCE SPECIFICATIONS
Model
ANT & ANR 300-10
ANT & ANR 515-40
ANT & ANR 515-80
ANT & ANR 800-100
ANT & ANR 870-150
ANT & ANR 975-200
ANT & ANR 1250-400
ANT & ANR 1900-600
Frequency
Range
DC-4.0 GHz
DC-2.5 GHz
DC-1.0 GHz
DC-2.0 GHz
DC-2.0 GHz
DC-1.0 GHz
DC-500 MHz
DC-500 MHz
Input Power
(Watts Avg.)
10
40
80
100
150
200
400
600
VSWR (Typical)
(Note 3)
1.25:1
1.15:1
1.25:1
1.25:1
1.25:1
1.25:1
1.50:1
1.50:1
Capacitance
(pF) (Typ.)
1.0
1.0
1.6
1.4
4.5
4.5
7.0
15.0
Figure
No.
1
2
2
3
4
5
6
7
PHYSICAL DIMENSIONS
TERMINATIONS (ANT) SERIES
RESISTORS (ANR) SERIES
ANT 300-10 — 10 WATTS
Flange Mounted
ANR 300-10 — 10 WATTS
Flange Mounted
FIGURES
FIG. 1
.005±.001 [0.13±0.03]
.110 [2.79]
.030 [0.76]
.125 [3.17] MIN
.040 [1.02]
.100 [2.54]
.300 [7.62]
.062 [1.57]
.200 [5.08]
.100 [2.54]
.116 [ 2.95]
.160 [4.06]
MAX
.200 [5.08]
ANT 515-40 — 40 WATTS
ANT 515-80 — 80 WATTS
Flange Mounted
ANR 515-40 — 40 WATTS
ANR 515-80 — 80 WATTS
Flange Mounted
FIG. 2
.095 [2.41]
.125 [3.18]
.250 [6.35]
.125 [3.18]
.250 [6.35]
MIN
.116 [2.95]
ANT 800-100 — 100 WATTS
Flange Mounted
ANR 800-100 — 100 WATTS
Flange Mounted
.160
MAX
.062 [1.57]
.060 [1.52] TYP
FIG. 3
.250 [6.35]
MIN
.130 [3.3]
.003±.001
[0.08±0.03]
.515
(13.08)
.800 [20.32]
.560 [14.22]
.130 [3.30]
THRU 2 PLS
.115 [2.92]
.120 [3.05]
.230 [5.84]
.150 [3.81] MIN
.040 [1.02]
.005±.001 [0.13±0.03]
TAB THICKNESS
.400 [10.16]
.150 [3.81] MAX
.108 [2.74]
.060 [1.52]
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
REV 04/11
SERIES ANT, ANR
RESISTORS & TERMINATIONS
PHYSICAL DIMENSIONS
TERMINATIONS (ANT) SERIES
RESISTORS (ANR) SERIES
FIGURES
ANT 870-150 — 150 WATTS
Flange Mounted
ANR 870-150 — 150 WATTS
Flange Mounted
FIG. 4
.870 [22.10]
.560 [14.22]
.161 [4.09]
THRU 2 PLS
.155 [3.94]
.375 [9.52]
.125 [3.18] MIN
.120 [3.05]
.187 [4.76]
.108 [2.74]
.250 [6.35]
.003±.001 [0.08±0.03]
.160 [4.06] MAX
.062 [1.57]
ANT 975-200 — 200 WATTS
Flange Mounted
ANR 975-200 — 200 WATTS
Flange Mounted
FIG. 5
.975 [24.77]
.725 [18.41]
.300 [7.62]
.125 [3.17]
.188 [4.76]
.375 [9.52]
.125 [3.18] MIN
.120 [3.05]
.003±.001 [0.08±0.03]
.375 [9.53]
.200 [5.08] MAX
.125 [3.17]
THRU 2 PLS
.110 [2.79]
.171 [4.34]
ANT 1250-400 — 400 WATTS
Flange Mounted
ANR 1250-400 — 400 WATTS
Flange Mounted
FIG. 6
1.250[31.8]
.171[4.34]
.003±.001
[0.08±0.03]
.500
[12.7]
.120[3.05]
TYP.
.160[4.06]
DIA TYP.
.125
[3.18]
MIN.
500[12.7]
.250[6.4]
.125[3.18]
.875
[22.23]
ANT 1900-600 — 600 WATTS
Flange Mounted
ANR 1900-600 — 600 WATTS
Flange Mounted
FIG. 7
.210[5.33]
MAX.
1.900 [48.26]
1.550 [39.37]
1.000 [25.40]
.175 [4.45]
.125 [3.18]
.270 [6.86]
1.040
[26.42]
.500 [12.70]
.125 [3.18] MIN
C
L
.250 [6.35]
.166 [4.22]
THRU 4 PLS
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
300 Dino Drive, Ann Arbor, MI 48103
Tel: 888-244-6638 or 734-426-5553 • Fax: 734-426-5557
www.aeroflex.com/inmet • [email protected]
.005±.001 [0.13±0.03]
.195 [4.95]
.250 [6.35]
MAX
A3RS91.1
High Power Chip Termination
100 Watts
When properly mounted on an appropriate heat sink, this chip
device provides high power dissipation capabilities. Ideal
for ferrite isolator applications, the improved thin film design
technology and laser trimming provide proven RF power
capabilities to meet the demands of today's CDMA and
WCDMA system requirements. Aluminum Nitride is featured
for those applications where the use and disposal of Beryllium
oxide is a concern.
• Environmentally friendly AlN substrate
• High performance, thin film element
• Power 100 Watts
• New adhesion process results in improved
terminal strength
• On-chip matching network improves frequency
performance over the DC-3 GHz frequency range
PHYSICAL DIMENSIONS
SPECIFICATIONS
Parameters
Specifications
Frequency Range
DC to 3 GHz
Power
100 Watts*
VSWR
1.10:1 max
Resistance
50 Ohms +/- 5%
Operating Temperature
-55 °C to 150 °C
Substrate
Aluminum Nitride
.225 REF
[5,72] REF
.045
[1,14]
.350REF
[8,89]REF
* Refer to average power derating curve chart.
TYPICAL PERFORMANCE
.050
[1,27]
.040 REF
[1,02]
A3RS91.1
WRAP AROUND
AVERAGE POWER DERATING CURVE
% OF RATED POWER
100
75
50
25
0
25
50
75
100
125
150
CHIP BASE TEMP ºC
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
300 Dino Drive, Ann Arbor, MI 48103
Tel: 888-244-6638 or 734-426-5553 • Fax: 734-426-5557
www.aeroflex.com/inmet • [email protected]
REV 04/11
SERIES ANC
RESISTORS, TERMINATIONS
High Power Chip, Aluminum Nitride – 50 & 100 Ohms
GENERAL INFORMATION
When mounted on an appropriate heat sink, these chip devices
provide high power dissipation in terminations and as balancing
resistors in Wilkinson power divider networks. Laser trimming
provides maximum RF power capability. Aluminum nitride
is used for those applications where the use and disposal of
beryllium oxide is a concern.
ORDERING INFORMATION
EXAMPLE: Typical Model No.
ANC
NPC
T 250-250 X
50R0 (See Note 1 Below)
or
1000 J
Prefix
PHYSICAL DIMENSIONS
Tinning (See Note 2)
H = Sn96
T = Sn63
Tolerance Key
F = 1%
G = 2%
J = 5% (Standard)
Size
Terminal type (X or G)
(NARROW FILM)
(FULL FILM)
TOP
VIEW
Ohmic Value (Note 1)
W
A
NOTES
1. Resistance value is expressed using military 4-digit call-out.
50R0 = 50 Ohms
1000 = 100 Ohms
B
Other values from 10–500 Ohms may be available as special order.
Contact factory for availability.
B
TYPE X
(RESISTOR)
2. Tinning with Sn96 “Lead Free” high temperature solder will maintain RoHS
compliance.
50 Ohms
or
100 Ohms
T
L
B
TYPE G
(TERMINATION)
GENERAL SPECIFICATIONS
Solderable Terminals
Electroplated Silver over Nickel
Substrate
Aluminum Nitride
Resistive Element
Thin Film
50 Ohms
ONLY
T
L
0.005
[0.13]
MAX
PERFORMANCE SPECIFICATIONS
W
Model Prefix
in
L
[mm]
in
T
[mm]
in
A
[mm]
in
B
[mm]
in
Capacitance Termination
(pF)
VSWR
[mm]
Typical
Typical
Power
CW
FREQ.
GHz
ANC 50-50
0.050 [1,27] 0.050 [1,27] 0.010 [0,25]
N/A
0.010 [0,25]
0.5
1.25
5
DC-4.0
ANC 50-100
0.050 [1,27] 0.100
[2,5] 0.010 [0,25]
N/A
0.020 [0,51]
1.0
1.25
10
DC-2.0
N/A
DC-4.0
ANC 100-200
0.100
[2,5] 0.200
[5,1] 0.040 [1,02]
0.030 [0,76]
1.0
1.25
10
ANC 200-200
0.200
[5,1] 0.200
[5,1] 0.040 [1,02] 0.085
[2,2]
0.040 [1,02]
1.2
1.25
30
DC-4.0
ANC 250-250-40
0.250
[6,4] 0.250
[6,4] 0.040 [1,02] 0.085
[2,2]
0.050 [1,27]
1.0
1.15
40
DC-2.5
ANC 250-250-80
0.250
[6,4] 0.250
[6,4] 0.040 [1,02]
N/A
0.050 [1,27]
1.6
1.25
80
DC-1.0
ANC 250-375
0.250
[6,4] 0.375
[9,5] 0.040 [1,02]
N/A
0.050 [1,27]
4.5
1.25
125
DC-1.0
ANC 350-225
0.350
[8,9] 0.225
[5,7] 0.040 [1,02] 0.045
[1,14] 0.050 [1,27]
1.4
1.25
100
DC-2.0
ANC 375-375
0.375
[9,5] 0.375
[9,5] 0.040 [1,02] 0.250
[6,4] 0.050 [1,27]
4.5
1.25
200
DC-1.0
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
300 Dino Drive, Ann Arbor, MI 48103
Tel: 888-244-6638 or 734-426-5553 • Fax: 734-426-5557
www.aeroflex.com/inmet • [email protected]
REV 04/11
SERIES KAC
Surface Mount Terminations (SMT)
High Power, Aluminum Nitride (AlN), 10 - 150 Watts
GENERAL INFORMATION
Aeroflex / Inmet’s series of High PowerSurface MountTerminations
are ideal for high frequency applications where small size and
low costs are an important design criteria. The ability of these
chips to be directly mounted to the PC Board eliminates the need
for expensive mounting flanges and input tabs. Large solderable
surface areas on the bottom of the chips allows for higher power
dissipation in smaller sizes. All KAC series chips are manufactured using environmentally friendly Aluminum Nitride ceramic
and are classified as RoHS compliant.
ORDERING INFORMATION
EXAMPLE: Typical Model No.
KAC
NPC
T 100-200A X
Z 50R0
G
Prefix
Tinning (Optional)
H = Sn96
T = Sn63
PHYSICAL DIMENSIONS
Size
Terminal type
Ohmic Value
Tolerance, G = 2% (Standard)
NOTE
Tinning with Sn96 “Lead Free” high temperature solder will maintain RoHS
compliance.
GENERAL SPECIFICATIONS
Substrate
Aluminum Nitride
Solderable Terminals
Electroplated Silver over Nickel
Resistive Element
Proprietary Thick Film
Operating Temperature
-55 to +150ºC
Impedance (Nominal)
50 Ohms
PERFORMANCE SPECIFICATIONS
W
Model Prefix
KAC 60 – 120A
in
L
(mm)
in
T
(mm)
in
A
(mm)
in
B
(mm)
in
C
(mm)
in
(mm)
0.060 (1,52) 0.120 (3,05) 0.025 (0,64) 0.054 (1,37) 0.026 (0,66) 0.013 (0,33)
KAC 100 – 200A 0.100
Power
CW
Frequency
GHz
1.25
10
DC – 4.0
1.25
20
DC – 2.5
VSWR
(2,5)
0.200 (5,1) 0.040 (1,02) 0.050 (1.27) 0.025 (0,64) 0.035 (0,89)
KAC 250 – 250A 0.250
(6,4)
0.250 (6,4) 0.040 (1,02) 0.040 (1,02) 0.043 (1,09) 0.020 (0,51)
1.25
75
DC – 4.0
KAC 250 – 375A 0.250
(6,4)
0.375 (9,5) 0.040 (1,02) 0.135 (3,43) 0.058 (1,47) 0.060 (1,52)
1.25
100
DC – 3.0
KAC 375 – 375A 0.375
(9,5)
0.375 (9,5) 0.040 (1,02) 0.125 (3,18) 0.057 (1,48) 0.030 (0,76)
1.25
150
DC – 3.0
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
300 Dino Drive, Ann Arbor, MI 48103
Tel: 888-244-6638 or 734-426-5553 • Fax: 734-426-5557
www.aeroflex.com/inmet • [email protected]
REV 04/11
SERIES PCX
HIGH POWER COAXIALTERMINATIONS
DC to 6 GHz
GENERAL INFORMATION
The PCX Series High Power Terminations are designed to
dissipate RF power when mounted to a heat sink or chill plate.
Power levels up to 500 watts in 50 ohm impedance are available in units with SMA or Type N, male or female connectors.
High stability thin film resistive elements on beryllium oxide
substrates are used to insure stable VSWR performance over
temperature and environmental conditions.
NOTES
1. Input power ratings based on case temperature of 85°C maximum.
2. Connectors: SMA - Stainless Steel Passivated per MIL-C-39012,
Type N - Nickel Plated Brass per MIL-C-39012
3. Housing: Copper, Nickel Plated per QQ-N-290
PERFORMANCE SPECIFICATIONS
Part Number
Input Power (Watts)
(Note 1)
Frequency
Range
Connector Type
(Note 2)
VSWR
(Typical)
Outline
PCX050-F-50
PCX050-M-50
50
DC - 6 GHz
SMA Female
SMA Male
DC-3 GHz:
3 - 6 GHz:
1.25:1
1.35:1
A
PCX050-F-100
PCX050-M-100
100
DC - 3 GHz
SMA Female
SMA Male
DC- 3 GHz:
1.25:1
A
PCX050-F-150
PCX050-M-150
PCX100-F-150
PCX100-M-150
150
DC - 2 GHz
SMA Female
SMA Male
N Female
N Male
DC - 1 GHz:
1 - 2 GHz:
1.15:1
1.40:1
B
PCX050-F-250
PCX050-M-250
PCX100-F-250
PCX100-M-250
250
DC -800 MHz
SMA Female
SMA Male
N Female
N Male
DC - 200 MHz: 1.15:1
200 - 400 MHz: 1.40:1
400-800 MHz: 1.30:1
B
PCX100-M-500
500
DC - 200 MHz
N Male
DC - 200 MHz:
B
1.15:1
PHYSICAL DIMENSIONS
.960[24.38]
.625
[15.88]
"Y"
.090
[2.29]
"X"
1.25
[31.8]
1.375
1.25
[34.93] [31.8]
MODEL
"X"
"Y"
"Z"
PCX050-F-50
.375
[9.53]
.560
[14.22]
.260
[6.60]
PCX050-M-50
.507
[12.88]
.560
[14.22]
.260
[6.60]
PCX050-F-100
.375
[9.53]
.560
[14.22]
.260
[6.60]
PCX050-M-100
.507
[12.88]
.560
[14.22]
.260
[6.60]
.120 [3.05] DIA.
4 HOLES
"Z"
.125 [3.18]
SMA 50 & 100 WATTS
OUTLINE A (Shown with SMA)
1.625
[41.28]
.875
[22.23]
2.000
[50.8]
1.625
[41.28]
1.060
[26.92]
.180
[4.57]
"X"
.375
[9.53]
1.250
[31.8]
.187 [4.75]
.215 [5.46] DIA.
4 HOLES
"Y"
MODEL
"X"
"Y"
PCX050-F-150, 250
[9.53]
[13.08]
.375
.515
PCX050-M-150, 250
[9.53]
[13.08]
.375
.515
PCX100-F-150, 250, 500
[18.69]
[12.9]
.736
.508
PCX100-M-150, 250, 500
[20.8]
[12.9]
.819
.508
SMA OR N CONNECTORS
150, 250 & 500 WATTS
OUTLINE B (Shown with TYPE N)
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
300 Dino Drive, Ann Arbor, MI 48103
Tel: 888-244-6638 or 734-426-5553 • Fax: 734-426-5557
www.aeroflex.com/inmet • [email protected]
REV 04/11
SERIES PPC, NPC
RESISTORS, TERMINATIONS
High Power Chip – 50 & 100 Ohms
GENERAL INFORMATION
When mounted on an appropriate heat sink, these chip devices
provide high power dissipation in terminations and as balancing
resistors in Wilkinson power divider networks. Laser trimming
provides maximum peak and average RF power capability.
ORDERING INFORMATION
EXAMPLE: Typical Model No.
PPC
or
NPC
T
25-50 X X
50R0 (See Note A Below)
or
1000
J
Physical Dimensions
Prefix
Tinning (see Note 4)
H = Sn96
T = Sn63
Size
TOP
VIEW
Tolerance Key
W
F = 1%
G = 2%
J = 5% (Standard)
Terminal type (X, W or G)
Ohmic Value (Note A)
B
B
NOTE A
Resistance value is expressed using military 4-digit call-out.
50R0 = 50 Ohms
1000 = 100 Ohms
TYPE X
Other values from 10–500 Ohms may be available as special order.
Contact factory for availability.
L
GENERAL SPECIFICATIONS
Solderable Terminals
50 Ohms
or
100 Ohms
T
B
B
Electroplated Silver over Nickel (PPC)
Gold over Nickel alloy (NPC)
Substrate
Beryllium Oxide Ceramic
Resistive Element
Thin Film and Thick Film*
TYPE G
T
50 Ohms
ONLY
L
NOTES
0.005[0.13] MAX
1. The “L” and “T” dimensions are for the substrate only and do not include
terminal thickness or optional tinning thickness.
B
B
2. Thermal Resistance (R°) is measured in °C/W between resistive film and
mounting surface.
3. The CW power rating is based on maximum film temperature of +150°C and with
maximum heatsink temperature of +100°C. Power is based on infinite and ideal
heatsink. Type “W” termination style does not have full back plane metallization
and typically handles 1/10 the rated power.
TYPE W
(Note 3)
50 Ohms
or
100 Ohms
T
L
4. Tinnning with Sn96 “Lead Free” high temperature solder will maintain RoHS
compliance.
PERFORMANCE SPECIFICATIONS
W
Model
Prefix
in
[mm]
L
(Note 1)
in
[mm]
T
(Note 1)
in
[mm]
B
in
[mm]
Capacitance
(pF) Typical
RØ °
C/W Max.
(Note 2)
C/W
Power
Freq.
GHz (**)
DC-4.0
*PPC 100-200A
0.100
[2,5]
0.200
[5,1]
0.040
[1,02]
0.030
[0,76]
0.8
0.80
20W
*PPC 250-250A
0.250
[6,4]
0.250
[6,4]
0.040
[1,02]
0.050
[1,27]
1.2
0.30
40W
DC-2.5
*PPC 250-375A
0.250
[6,4]
0.375
[9,53]
0.040
[1,02]
0.050
[1,27]
3.5
0.15
150W
DC-1.0
NPC 25-50
0.025
[0,64]
0.050
[1,27]
0.010
[0,25]
0.012 [0,305]
0.3
3.90
3W
*NPC 50-50
0.050
[1,27]
0.050
[1,27]
0.010
[0,25]
0.012 [0,305]
0.5
1.90
5W
DC-10
*NPC 50-100
0.050
[1,27]
0.100
[2,5]
0.010
[0,25]
0.017
[0,43]
1.0
0.72
10W
DC-4.0
NPC 75-150
0.075
[1,91]
0.150
[3,8]
0.010
[0,25]
0.020
[0,51]
1.8
0.29
15W
DC-4.0
DC-12.4
* Low cost thick film models available on these sizes. Consult factory for specifications.
** Typical VSWR for all terminations is 1.25:1
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
300 Dino Drive, Ann Arbor, MI 48103
Tel: 888-244-6638 or 734-426-5553 • Fax: 734-426-5557
www.aeroflex.com/inmet • [email protected]
REV 04/11
SERIES PPA
ATTENUATORS
High Power – DC-4 GHz
The Aeroflex/Inmet PPA Series of attenuators utilize a Beryllium
Oxide chip and thin film technology to provide devices which
can dissipate up to 100 Watts of RF power. The PPA series
must be thermally bonded to a heat sink, using the mounting
holes provided, in order to operate within the temperature
rating indicated. The flange temperatures must not exceed
100°C under rated power conditions.
GENERAL SPECIFICATIONS
ORDERING INFORMATION
The Power Attenuators listed are available in 1 dB increments
from 1 thru 20 dB. Specify by selecting any of the series listed
and add the attenuation value desired to the basic series
designation. (See Note 3)
Desired dB
Value
Power
50 Ohms
Operating Temp.
–55 °C to +150°C
Attenuation Stability 0.0001 dB/dB/°C
PPA 20-10
Basic
Series PPA
Impedance
Substrate
Beryllium Oxide Ceramic
Resistive Element
Proprietary Thin Film
Flange
Copper, Nickel Plated per QQ-N-290
Tabs
Beryllium Copper, Gold Plated per MIL-G-45204
Cover
Alumina Ceramic
PERFORMANCE SPECIFICATIONS
Attenuation(1)
1 dB Increments
(dB)
Frequency(1)
Range
PPA 10
11-20
1-20
DC-4 GHz
10
1-10
±0.5
±1.0
±0.5
±2.0
±1.0
±3.0
PPA 20
6-9
10-15
16-20
1-20
DC-4 GHz
20
1-5
±0.5
±0.5
±0.75
±1.0
±0.5
±0.5
±1.0
±2.0
±0.5
±1.0
±1.5
±3.0
PPA 50
1-20
DC-1 GHz
50
±0.3 DC-500 MHz
±0.5 500 MHz-1 GHz
PPA 100
1-20
DC-500 MHz
100
±0.5
Model
Input
Power
(Watts)
Attenuation Accuracy (1)
(dB)
DC-1 GHz
1-2.5 GHz
dB
VSWR
(Typical)2
2.5-4 GHz
1.3:1
1.15:1 – DC-1.0 GHz
1.35:1 – 1.0-2.5 GHz
1.50:1 – 2.5-4.0 GHz
1.25:1 – DC-500 MHz
1.50:1 – 500 MHz–1 GHz
1.25:1 – DC-200 MHz
1.50:1 – 200-500 MHz
PHYSICAL DIMENSIONS
.040 [1.02] x
.005±.001 THK
[0.13±0.03]
NOTES
1. Custom products
.116 [2.95] DIA.
are available
at higher
MIN.
frequencies .125 [3.18]
TYP
with optimized
VSWR and
attenuation
accuracy over
narrow frequency .100 [2.54]
bandwidths.
2. VSWR as measured
in a 0.125” ground
plane stripline circuit.
3. Standard values
1, 2, 3, 4, 5, 6, 10, 20 dB.
Non-std values available
as special order.
.160 [4.06] MAX.
.003±.001 [0.08±0.03]
.375 [9.52]
.060 [1.52] TYP
.175 [4.45]
.171 [4.34]
.125 [3.18]
THRU 2 PLS
.300 [7.62]
.100 [2.54]
.200 [5.08]
.062 [1.58]
.375 [9.53]
.250 [6.35]
MIN TYP
.725 [18.42]
.110 [2.79]
.125 [3.18]
.105 [2.67]
.200 [5.08]
MAX
.975 [24.77]
PPA10 OUTLINE
.003±.001 [0.08±0.03]
1.250 [31.75]
.875 [22.23]
.060 [1.52] x
.003±.001 THK
[0.08±0.03]
.150 [3.81] MAX.
.250 [6.35] MIN.
TYP
PPA50 OUTLINE
.171 [4.34]
.405 [10.29]
.188 [4.76]
.116 [2.95] DIA.
.515 [13.08]
.250 [6.35]
MIN
.125 [3.18]
.250 [6.35]
.125 [3.18]
.500 [12.70]
.250 [6.35]
.250 [6.35]
MIN TYP
.062 [1.58]
.125 [3.18]
.060 [1.52] TYP
.500 [12.70]
.160 [4.06]
THRU PLS
.105 [2.67]
PPA20 OUTLINE
.210 [5.33]
MAX
PPA100 OUTLINE
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
300 Dino Drive, Ann Arbor, MI 48103
Tel: 888-244-6638 or 734-426-5553 • Fax: 734-426-5557
www.aeroflex.com/inmet • [email protected]
REV 04/11
SERIES PCA, PCAA
ATTENUATORS, CHIP
Low Power – DC-18 GHz
FEATURES
• Laser Trimmed
• Temperature Stable
GENERAL INFORMATION
The PCA and PCAA Series consists of a laser trimmed distributed thin film element on an alumina ceramic substrate with
solderable terminals. Two sizes are available. The PCA size
operates to 12.4 GHz and the PCAA size operates to 18.0 GHz.
Both sizes are available with leads and wrap around conductors for ease of installation. The PCAF and PCAAF options are
designed for “flip-chip” application in lower frequency circuits.
PCA & PCAA SERIES DATA
• Substrate: 96% Alumina
• Solderable Terminals: Electroplated Silver over Nickel
• Resistive Element: Proprietary Thin Film
• Wrap around Ground Terminal available, “W” option
• Wrap around-all terminals—“F” option
• Standard values 1, 2, 3, 4, 5, 6, 10, 20 dB
• Non-std. values available as special order
GENERAL SPECIFICATIONS
ORDERING INFORMATION
The attenuators listed are available in 1 dB increments from 1
through 20 dB. When ordering, to specify the correct part number for the desired attenuation value, select any of the series
listed and add the attenuation value desired to the basic series
designation.
Basic Option(s)
Series
L
W
F
EXAMPLES:
0.0001 dB/dB/°C
POWER DERATING
(x)
(x)
Attenuation Stability
% OF RATED POWER
PCA
or
PCAA
50 Ohms
–55°C to +150°C
AVERAGE POWER DERATING CURVE
Options (Note 4)
L = Lead/Tab (Gold Plated BeCu)
W = Wrap around ground only
F = Wrap around all terminals (flip-chip)
T = Tinned terminals (any terminal type) Sn63
H = Tinned terminals (any terminal type) Sn96
G = Gold plated terminals
EXAMPLE:
Impedance
Operating Temperature
25
0
85
25
150°C
NOTES
dB
Value
Option(s)
T
H
G
100
75
50
1. Performance of other dB values vary dependent on attenuation.
Contact factory for specifications for fractional dB values.
2. Performance is based on device mounted in matched 50 Ohm line.
3. Rated power 1.5 Watts input PCA, 100 mw PCAA.
PCAW-T3
PCAAF-G3
4. Tinning with Sn96 “Lead Free” high temperature solder will maintain RoHS
compliance.
PERFORMANCE SPECIFICATIONS
Increments
(dB)
Note 1
DC - 4 GHz
PCA, PCAA
Series
Attenuation Accuracy (dB) Note 2
4 - 8 GHz
8 - 12.4 GHz
12.4 - 18 GHz
PCA, PCAA
PCA, PCAA
PCAA
Series
Series
Series Only
DC - 4 GHz
PCA, PCAA
Series
VSWR (Typical) Note 2
4 - 8 GHz
8 - 12.4 GHz 12.4 - 18 GHz
PCA, PCAA
PCA, PCAA
PCAA
Series
Series
Series Only
1-3
± 0.5
± 0.5
± 0.5
± 0.5
1.25
1.35
1.50
4-6
± 0.5
± 0.5
± 0.5
± 0.75
1.25
1.35
1.50
1.50
7 - 10
± 0.5
± 0.5
± 0.75
± 1.0
1.25
1.35
1.50
1.50
11 - 15
±0.75
+0.5
-3.0
+0.5
-4.0
—
1.25
1.35
1.50
—
16 - 20
± 1.0
+0.5
-4.0
—
—
1.25
1.35
—
—
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
1.50
SERIES PCA, PCAA
ATTENUATORS, CHIP
Low Power – DC-18 GHz
PHYSICAL DIMENSIONS
PCAW
(WRAP AROUND GROUND TERMINAL ONLY)
PCA
.025[0.64]
MIN
.025[0.64]
MIN
.010
[0.25]
.060 [1.52]
TYP.
.125
[3.18]
.060[1.52]
TYP.
.125
[3.18]
.150
[3.8]
GROUND
.150
[3.8]
.015[0.38] MIN
WRAP AROUND GROUND
.015[0.38]
MIN
PCAF (WRAP AROUND ALL TERMINALS)
PCAL (LEAD/COVER)
.150
[3.8]
.010
[0.25]
.250 [6.4]
MIN
.040 [1.02]
MAX
MAXIMUM
FREQUENCY
4 GHz
.010
[0.25]
.025 MIN
[0.64]
.125
[3.18]
.060 [1.52]
TYP.
.125
[3.18]
WRAP
AROUND
TERM TYP
(SIDE WRAP
OPTIONAL)
.150
[3.8]
.060±.003
[1.52±0.08]
TYP.
WRAP AROUND GROUND
(SIDE WRAP OPTIONAL)
.003±.001
[0.08±0.03]
.015 [0.38]
MIN
PCAAW
(WRAP AROUND GROUND TERMINAL ONLY)
PCAA
.025 [0.64]
TYP.
.025 [0.64]
TYP.
.010
[0.25]
.020 [0.5] TYP.
.060
[1.52]
.010
[0.25]
.020[0.5] TYP.
.060
[1.52]
.075
[1.9]
.075
[1.9]
GROUND
.015[0.38] MIN
WRAP AROUND GROUND
.015 [0.38] MIN
PCAAF (WRAP AROUND ALL TERMINALS)
PCAAL (LEAD/COVER)
.075 .250 [6.4]
[1.9]
MIN
.040 [1.02]
MAX
.060
[1.52]
.025 [0.64]
TYP.
.010
[0.25]
.020 [0.5] TYP.
.060
[1.52]
.020±.003
[0.5±0.08]
TYP.
.003±.001
[0.08±0.03]
MAXIMUM
FREQUENCY
8 GHz
WRAP AROUND TERM TYP
(SIDE WRAP OPTIONAL)
.075
[1.9]
WRAP AROUND GROUND
(SIDE WRAP OPTIONAL)
.015 [0.38] MIN
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
300 Dino Drive, Ann Arbor, MI 48103
Tel: 888-244-6638 or 734-426-5553 • Fax: 734-426-5557
www.aeroflex.com/inmet • [email protected]
REV 04/11
SERIES PPR, PPT
RESISTORS & TERMINATIONS
High Power, Thin Film, Drop-in – 10-650 Watts, DC-4 GHz
GENERAL INFORMATION
These high power devices are designed to dissipate power in
RFcircuits when mounted to an appropriate heat sink. The terminations provide a low VSWR under maximum power conditions. The resistor configurations are typically used in
“Wilkinson” type power divider networks, or to terminate 3 dB
stripline or microstrip hybrids.
NOTES
1. Input power ratings are based on flange temperature of 100° C maximum.
2. 50 and 100 Ohms standard. Other values from 10-500 Ohms available on
special order. Contact factory for details. Standard tolerance ±5%.
Specify resistance value when ordering.
3. VSWR applies to termination style only.
% OF RATED POWER
AVERAGE POWER DERATING CURVE
GENERAL SPECIFICATIONS
Resistive Element
Substrate
Cover
Mounting Flange
Tab
Thin Film and Thick Film*
Beryllium Oxide Ceramic
Alumina Ceramic
Copper,Nickel Plated per QQ-N-290
Beryllium Copper,Gold Plated per MIL-G-45204
POWER DERATING
100
75
50
25
0
25
100
125
75
50
FLANGE TEMPERATURE — °C
150
* Low cost thick film models available on some sizes.Consult Factory for specifications.
PERFORMANCE SPECIFICATIONS
Model
PPR & PPT 300-10-3*
PPR & PPT 515-20-3*
Frequency
Range
DC-4.0 GHz
DC-2.0 GHz
Input Power
(Watts Avg.)
10
20
PPT 515-30-4
PPR & PPT 515-30*
DC-4.0 GHz
DC-2.0 GHz
30
30
PPR & PPT 800-40-3
PPT 800-100A
PPR & PPT 870-150-3*
DC-4.0 GHz
DC-2.0 GHz
DC-1.0 GHz
40
100
150
PPR & PPT 975-250-3
DC-1.0 GHz
250
PPR & PPT 1250-400
PPR &PPT 1900-800
DC-500 MHz
DC-500 MHz
400
VSWR (Typical)
(Note 3)
1.35:1 —DC-4.0 GHz
1.10:1 —DC-1.0 GHz
1.25:1 —1.0-2.0 GHz
1.20:1 —DC-40 GHz
1.10:1 —DC-1.0 GHz
1.25:1 —1.0-2.0 GHz
1.25:1 —DC-4.0 GHz
1.25:1 —DC-2.0 GHz
1.20:1 —DC-500 MHz
1.35:1 —500-1000 MHz
1.25:1 —DC-500 MHz
1.35:1 —500-1000 MHz
1.50:1 —DC-500 MHz
1.25:1 —DC-200 MHz
1.50:1 —200-500 MHz
650
Capacitance
(pF) (Typ.)
0.8
0.8
Figure
No.
1
2
1.2
0.8
3
4
1.4
1.4
5
6
3.5
7
5.0
8
7.0
10.2
9
10
PHYSICAL DIMENSIONS
TERMINATIONS (PPT) SERIES
RESISTORS (PPR) SERIES
FIGURES
PPT 300-10-3 — 10 WATTS
Flange Mounted
PPR 300-10-3 — 10 WATTS
Flange Mounted
FIG. 1
.030 [0.76]
.125 [3.17] MIN
.005±.001 [0.13±0.03]
.110 [2.79]
.040 [1.02]
.100 [2.54]
.300 [7.62]
.062 [1.57]
.200 [5.08]
.116 [ 2.95]
.160 [4.06]
MAX
.100 [2.54]
.200 [5.08]
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
REV 4/11
SERIES PPR, PPT
RESISTORS & TERMINATIONS
PHYSICAL DIMENSIONS
TERMINATIONS (PPT) SERIES
RESISTORS (PPR) SERIES
FIGURES
PPT 515-20-3 — 20 WATTS
Flange Mounted
PPR 515-20-3 — 20 WATTS
Flange Mounted
FIG. 2
.095 [2.41]
.160 [4.06]
MAX
.062 [1.57]
.060 [1.52] TYP
.125 [3.18]
.250 [6.35]
.125 [3.18]
.250 [6.35]
MIN
.116 [2.95]
PPT 515-30-4 — 30 WATTS
Flange Mounted
.250 [6.35]
MIN
.130 [3.30]
.003±.001
[0.08±0.03]
.515
[13.08]
FIG. 3
.515
[13.08]
.150 [3.81]
MAX
.062 [1.57]
.116 [2.95]
.250 [6.35]
MIN
Offered as a
Termination Only!
.250 [6.35]
.125 [3.18]
.250 [6.35]
MIN
.125 [3.18]
.110 [2.79]
.003±.001
[0.08±0.03]
.060 [1.52] TYP
.095 [2.41]
PPT 515-30 — 30 WATTS
Flange Mounted
PPR 515-30 — 30 WATTS
Flange Mounted
FIG. 4
.095 [2.41]
.160 [4.06]
MAX
.062 [1.57]
.060 [1.52] TYP
.125 [3.18]
.250 [6.35]
.125 [3.18]
.250 [6.35]
MIN
.116 [2.95]
PPT 800-40-3 — 40 WATTS
Flange Mounted
PPR 800-40-3 — 40 WATTS
Flange Mounted
FIG. 5
.250 [6.35]
MIN
.130 [3.30]
.003±.001
[0.08±0.03]
.515
(13.08)
.800 [20.32]
.560 [14.22]
.130 [3.30]
THRU 2 PLS
.115 [2.92]
.120 [3.05]
.230 [5.84]
.150 [3.81] MIN
.400 [10.16]
.150 [3.81] MAX
.060 [1.52]
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
.040 [1.02]
.005±.001 [0.13±0.03]
TAB THICKNESS
.108 [2.74]
SERIES PPR, PPT
RESISTORS & TERMINATIONS
PHYSICAL DIMENSIONS
TERMINATIONS (PPT) SERIES
RESISTORS (PPR) SERIES
PPT 800-100A — 100 WATTS
Flange Mounted
FIGURES
FIG. 6
.130 [3.30]
THRU 2 PLS
.800 [20.32]
.560 [14.22]
.115 [2.92]
.120 [3.05]
.230 [5.84]
Offered as a
Termination Only!
.150 [3.81] MIN
.040 [1.02]
.005±.001 [0.13±0.03]
TAB THICKNESS
.400 [10.16]
.150 [3.81] MAX
.108 [2.74]
.060 [1.52]
PPT 870-150-3 — 150 WATTS
Flange Mounted
PPR 870-150-3 — 150 WATTS
Flange Mounted
FIG. 7
.870 [22.10]
.560 [14.22]
.161 [4.09]
THRU 2 PLS
.155 [3.94]
.375 [9.52]
.125 [3.18] MIN
.120 [3.05]
.187 [4.76]
.108 [2.74]
.250 [6.35]
.003±.001 [0.08±0.03]
.160 [4.06] MAX
.062 [1.57]
PPT 975-250-3 — 250 WATTS
Flange Mounted
PPR 975-250-3 — 250 WATTS
Flange Mounted
FIG. 8
.975 [24.77]
.725 [18.41]
.300 [7.62]
.125 [3.17]
.188 [4.76]
.375 [9.52]
.125 [3.18] MIN
.120 [3.05]
.003±.001 [0.08±0.03]
.375 [9.53]
.200 [5.08] MAX
.125 [3.17]
THRU 2 PLS
.110 [2.79]
.171 [4.34]
PPT 1250-400 — 400 WATTS
Flange Mounted
PPR 1250-400 — 400 WATTS
Flange Mounted
FIG. 9
1.250[31.8]
.171[4.34]
.003±.001
[0.08±0.03]
.500
[12.7]
.120[3.05]
TYP.
.160[4.06]
DIA TYP.
.125
[3.18]
MIN.
500[12.7]
.250[6.4]
.125[3.18]
.875
[22.23]
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
.210[5.33]
MAX.
SERIES PPR, PPT
RESISTORS & TERMINATIONS
PHYSICAL DIMENSIONS
TERMINATIONS (PPT) SERIES
RESISTORS (PPR) SERIES
FIGURES
PPT 1900-800 — 650 WATTS
Flange Mounted
PPR 1900-800 — 650 WATTS
Flange Mounted
FIG. 10
1.900 [48.26]
1.550 [39.37]
1.000 [25.40]
.175 [4.45]
.125 [3.18]
.270 [6.86]
1.040
[26.42]
.500 [12.70]
.125 [3.18] MIN
C
L
.250 [6.35]
.166 [4.22]
THRU 4 PLS
KEY: Inches [Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
300 Dino Drive, Ann Arbor, MI 48103
Tel: 888-244-6638 or 734-426-5553 • Fax: 734-426-5557
www.aeroflex.com/inmet • [email protected]
.005±.001 [0.13±0.03]
.195 [4.95]
.250 [6.35]
MAX
Mounting Application Notes
Mounting of High Power Flange Devices
When mounting High Power Flange Devices
in a circuit, there are several key issues that
should be taken into account.
Heat Sink Design
The heat sink the device is mounted to must
be designed to maintain the temperature
(design) while it is dissipating the power
(heat) given it by the device. (The derating
specifications are given in the applicable
data sheets.)
Flatness of mating surfaces
Flatness of the heat sink and of the mounting area of the device (flange) should be
0.001” maximum. The idea is to have the
best possible contact between the heat sink
and the device.
Thermal Compound
To fill any microscopic voids or air gaps the
use of thermal compound is recommended
to a thickness of 0.002” maximum.
Stress Relief on Tab
Although it is not always possible in High
Frequency applications a small loop for
stress relief on the solder tab is recommended. This reduces any mechanical
stress on the joints.
Mounting of Chip Devices
Apply a small amount of thermal
compound to the mounting area of
the flange of the device. Spread it
completely on the flange using a razor
blade or other smooth tool. When seating
the device, align the tab/tabs over the
corresponding area on the circuit board.
Screw down the device using the recommended torque for the appropriate screw
size in the table below. Aeroflex / Inmet
recommends the use of a lock washer
and a flat washer in the installation.
See Figure 1
Thread Size
Torque Setting
2-56
4 inch-pounds
4-40
6 inch pounds
6-32
8 inch pounds
8-32
12 inch pounds
10-32
18 inch pounds
Solder the tab/tabs using SN63 (179° C
eutectic) solder and a small amount of
RMA flux. After all the solder is complete
all of the flux must now be removed using
a cleaning agent.
Figure 1: High Power Flange Device Mounting
TAB WITH STRESS RELIEF
DEVICE
THERMAL COMPOUND
SUBSTRATE
HEATSINK
This application note covers the recommended mounting techniques for the proper
conduction cooling and RF performance
of a surface mounted (flangeless) chip
attenuator, termination or resistor.
Initial Considerations
There are two primary considerations for
a surface mounted power device; Power
Dissipation and RF Performance. In order
to remove the dissipated power from this
type chip they must be provided with
adequate conductive cooling. This will
prevent excessive chip temperatures
leading to damage and early failure of the
device. RF performance is also dependent
on proper mounting. Since these devices
are being mounted to a circuit board,
inductance to ground is introduced by the
vias to the ground plane. To reduce this
effect and lower the thermal resistance
between the component and ground plane,
the following items are recommended:
1. Maximize the use of thermally conductive vias around and under the device.
2. Use of heavy copper cladding (2 oz.) on
the circuit board as a heat spreader.
Solders
Aeroflex / Inmet recommends the use of the
solders in the chart below when installing a
surface mount chip. Also listed are recommended platings for the heatsink/baseplate
that a device might be mounted to instead
of a circuit board.
Mounting
The first step when mounting a chip device
to the circuit board is to determine the
proper size and location of the solder
pads. Aeroflex / Inmet recommends providing
pads that are 0.010” to 0.020” over the
device’s termination size and are centered
on the axis of the chip. This allows for selfcentering of the chip and a proper solder
fillet formation. Skewing and “tombstoning”
can occur if this is not followed. See Figure 2
Preparation
1. Before any solder attachment, parts and
circuit boards must be free of any oils
or dirt. Isopropyl alcohol can be used
for this task.
2. Apply a small amount of RMA flux (MILF-14256) to the areas to be soldered.
3. SN63 solder is generally recommended
for use. This may be a preform, solder
paste or wire. If preforms are used,
select a size that is 0.005”to 0.010”
larger than the size of the pad.
4. When soldering is complete the circuit
board must be cleaned to remove any
flux residue. This can be done in an
ultrasonic cleaner or vapor degreaser.
Flux manufacturers have recommended
solvents or cleaning solutions for their
products.
Solder Type
Liquidous Temp. (degrees C.)
Recommended Platings for Heatsink/Baseplates
SN63
183 eutectic
Nickel, Silver
SN96
221 eutectic
Nickel, Silver
80Au/20Sn
280 eutectic
Gold over Nickel
Figure 2: Proper Mounting Techniques
DEVICE
SURFACE MOUNT
Pretinning
Pretinning can be done with either a solder
pot or by depositing and reflowing solder
on the device. (Aeroflex-Inmet can supply
pretinned devices, SN63 or SN96).
PCB PADS
Tabs
When attaching tabs to a device we
recommend using SN96 (221° C) to attach
the tab to the chip. Then, solder the tab to
the circuit board using SN63 (183 ° C).
Wire Bonding
Attach the device to the circuit board
using solder as described above. Clean
and remove any flux residues. Ultrasonically
bond wire or ribbon to gold termination
pads using a wedge or ball bonder.
NOTE: Gold plated chips are required
for this method.
Tuning
Maximum VSWR, as specified on the data
sheet, can be achieved without additional
tuning. Lower VSWR can be achieved
with stub or lumped element tuning.
However, this can result in a narrower
useable bandwidth.
OPENING IS
APPROXIMATELY
THE FILM AREA
OF THE CHIP
TAB WITH STRESS RELIEF
SUBSTRATE
DEVICE
SUBSTRATE
HEATSINK
300 Dino Drive, Ann Arbor, MI 48103
Tel: 888-244-6638 or 734-426-5553 • Fax: 734-426-5557
www.aeroflex.com/inmet • [email protected]
REV 5/11