160 MHz SAW Filter 4 MHz Bandwidth Part Number: SF0160CD02254T DESCRIPTION • • • 160 MHz SAW bandpass filter with 4 MHz bandwidth. 22.1 x 12.7 mm DIP package. RoHS compliant. TYPICAL PERFORMANCE Horizontal: Vertical from Top: S11 (150 to 170 MHz) Frequency : Relative Magnitude : Relative magnitude : Phase Linearity : Group Delay : 2 10 1 5 100 MHz/div dB/div dB/div deg/div ns/div S22 (150 to 170 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0160CD02254T Rev A 11-Mar-2010 ECN 36650 Page 1 of 3 160 MHz SAW Filter 4 MHz Bandwidth Part Number: SF0160CD02254T SPECIFICATION Parameter Center Frequency (Fc) 1 3 dB Bandwidth 40 dB Bandwidth Device Delay Insertion Loss Phase Linearity 2 Passband Variation 2 Rejection (10 to 156 MHz) Rejection (156 to Fo-2.9 MHz) Rejection (Fo+2.9 to 164 MHz) Rejection (164 to 280 MHz) Source and Load Impedance Ambient Temperature Notes: Min 159.90 4.00 50 45 45 50 - Typ 160.00 4.17 5.28 2.76 23.3 2.7 0.45 54 48 48 54 50 25 Max 160.10 5.80 25.0 5 0.7 - Units MHz MHz MHz µsec dB deg p-p dB p-p dB dB dB dB ohms °C 1. All specified bandwidths are centered at or referenced to this frequency. 2. Computed as the delta of the highest and lowest points inside the 3 dB Bandwidth. MAXIMUM RATINGS Parameter Storage Temperature Range Input Power Level Min Typ Max -40 - 25 10 85 13 Units ˚C dBm MATCHING CIRCUIT Ls1 Input 50 Ω Single-ended 1 Ls2 7 Cp1 Cp2 14 Output 50 Ω Single-ended 8 Typical component values: Ls1 Cp1 = = 100 33 nH pF Ls2 Cp2 = = 100 24 nH pF Notes: 1. Recommend use of 2% tolerance matching components. Inductor Q=45. 2. Component values are for reference only and may change depending on board layout. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0160CD02254T Rev A 11-Mar-2010 ECN 36650 Page 2 of 3 160 MHz SAW Filter 4 MHz Bandwidth Part Number: SF0160CD02254T PACKAGE OUTLINE Units: mm Tolerances are ±0.15 mm except where indicated and for the overall length and width, which are nominal values. Pin Configuration: Input: Input return: Output: Output return: Ground: 1 14 7 8 2,9 ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0160CD02254T Rev A 11-Mar-2010 ECN 36650 Page 3 of 3